74VCX16374 LOW VOLTAGE 16-BIT D-TYPE FLIP FLOP (3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS ■ ■ ■ ■ ■ ■ ■ ■ 3.6V TOLERANT INPUTS AND OUTPUTS HIGH SPEED: tPD = 3.0 ns (MAX.) at VCC = 3.0 to 3.6V tPD = 3.9 ns (MAX.) at VCC = 2.3 to 2.7V tPD = 7.8 ns (MAX.) at VCC = 1.8V POWER-DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24 mA (MIN) at VCC = 3.0V |IOH| = IOL = 18 mA (MIN) at VCC = 2.3V |IOH| = IOL = 6 mA (MIN) at VCC = 1.8V OPERATING VOLTAGE RANGE: VCC (OPR) = 1.8V to 3.6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 16374 LATCH-UP PERFORMANCE EXCEEDS 300mA ESD PERFORMANCE: HBM >2000V; MM > 200V T (TSSOP48 Package) ORDER CODES : 74VCX16374T PIN CONNECTION DESCRIPTION The VCX16374 is a low voltage CMOS 16-BIT D-TYPE FLIP FLOP with 3 STATE OUTPUT NON INVERTING fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 1.8 to 3.6V applications; it can be interfaced to 3.6V signal enviroment for both inputs and outputs. These 16 bit D-Type flip-flops are controlled by two clock inputs (nCK) and two output enable inputs (nOE). On the positive transition of the (nCK), the nQ outputs will be set to the logic state that were setup at the nD inputs. While the (nOE) input is low, the 8 outputs (nQ) will be in a normal state (high or low logic level) and while high level the outputs will be in a high impedance state. Any output control does not affect the internal operation of flip flops; that is, the old data can be retained or the new data can be entered even while the outputs are off. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. December 1999 1/11 74VCX16374 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION IEC LOGIC SYMBOLS PIN No SYMBOL NAME AND FUNCT ION 1 1OE 2, 3, 5, 6, 8, 9, 11, 12 1Q0 to 1Q7 3 State Outputs 13, 14, 16, 17, 19, 20, 22, 23 2Q0 to 2Q7 3 State Outputs 24 2OE 3 State Output Enable Input (Active LOW) 25 2CK Clock Input (LOW to HIGH, edge triggered) 36, 35, 33, 32, 30, 29, 27, 26 2D0 to 2D7 Data Inputs 47, 46, 44, 43, 41, 40, 38, 37 1D0 to 1D7 Data Inputs 48 1CK Clock Input (LOW to HIGH, edge triggered) 4, 10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive Supply Voltage 3 State Output Enable Input (Active LOW) TRUTH TABLE INPUT S CK D H X X Z X NO CHANGE L Q L L L L H H X:”H” or ”L” Z: High Impedance 2/11 OUTPUTS OE 74VCX16374 LOGIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Supply Voltage -0.5 to + 4.6 V VI DC Input Voltage -0.5 to + 4.6 V VO DC Output Voltage (OFF state) VO DC Output Voltage (High or Low State) (note1) VCC -0.5 to + 4.6 V -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 50 mA IOK DC Output Diode Current (note2) ± 50 mA IO DC Output Source/Sink Current ± 50 mA DC VCC or Ground Current Per Supply Pin ± 100 mA 400 mW ICC orIGND PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 o 300 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 1) IO absolute maximum rating must be observed 2) VO < GND, VO > VCC RECOMMENDED OPERATING CONDITIONS Symbol VCC Value Unit Supply Voltage Parameter 1.8 to 3.6 V -0.3 to 3.6 V VI Input Voltage VO Output Voltage (OFF state) 0 to 3.6 V VO Output Voltage (High or Low State) 0 to VCC V IOH, IOL High or Low Level Output Current (VCC = 3.0 to 3.6V) ± 24 mA IOH, IOL High or Low Level Output Current (VCC = 2.3 to 2.7V) ± 18 mA IOH, IOL High or Low Level Output Current (VCC = 1.8V) ±6 mA Top dt/dv Operating Temperature: Input Transition Rise or Fall Rate (V CC = 3.0V) (note 1) -40 to+85 0 to 10 o C ns/V 1) VIN from0.8V to 2.0V, VCC = 3.0V 3/11 74VCX16374 DC SPECIFICATIONS (2.7V < VCC ≤ 3.6V unless otherwise specified) Symb ol Parameter Test Co nditi ons VIH High Level Input Voltage VIL Low Level Input Voltage VOH High Level Output Voltage Min. Max. V 0.8 IO=-100 µA VCC-0.2 IO=-12 mA 2.2 IO=-18 mA 2.4 3.0 IO=-24 mA 2.2 2.7 to 3.6 IO=100 µA 0.2 IO=12 mA 0.4 IO=18 mA 0.4 IO=24 mA 0.55 2.7 to 3.6 VI = VIH or VIL 3.0 Low Level Output Voltage Un it 2.0 2.7 to 3.6 2.7 VOL Value -40 to 85 o C V CC (V) VI = VIH or VIL 2.7 3.0 3.0 V V V Input Leakage Current 2.7 to 3.6 VI = 0 to 3.6 V ±5 µA IOZ 3 State Output Leakage Current 2.7 to 3.6 VI = VIH orVIL VO = 0 to 3.6V ±10 µA Ioff Power Off Leakage Current 0 VI orVO = 0 to 3.6V 10 µA ICC Quiescent Supply Current µA II ∆ICC ICC incr. per input 2.7 to 3.6 2.7 to 3.6 VI = VCC orGND 20 VI orVO = VCC to 3.6 V ±20 VIH = VCC -0.6V 750 µA DC SPECIFICATIONS (2.3V < VCC ≤ 2.7V unless otherwise specified) Symb ol Parameter Test Co nditi ons VIH High Level Input Voltage VIL Low Level Input Voltage VOH High Level Output Voltage Un it Max. 1.6 V 0.7 IO=-100 µA 2.3 to 2.7 VI = VIH or VIL 2.0 IO=-12 mA 1.8 2.3 IO=-18 mA 1.7 2.3 to 2.7 IO=100 µA 0.2 IO=12 mA 0.4 IO=18 mA 0.6 2.3 2.3 VI = VIH or VIL V VCC-0.2 IO=-6 mA 2.3 Low Level Output Voltage Min. 2.3 to 2.7 2.3 VOL Value -40 to 85 o C V CC (V) V V Input Leakage Current 2.3 to 2.7 VI = 0 to 3.6 V ±5 µA IOZ 3 State Output Leakage Current 2.3 to 2.7 VI = VIH orVIL VO = 0 to 3.6V ±10 µA Ioff Power Off Leakage Current 0 VI orVO = 0 to 3.6V 10 µA ICC Quiescent Supply Current 2.3 to 2.7 VI = VCC orGND 20 VI orVO = VCC to 3.6 V ±20 µA II 4/11 74VCX16374 DC SPECIFICATIONS (1.8V ≤ VCC ≤ 2.3V unless otherwise specified) Symb ol Parameter Test Co nditi ons Value VIH High Level Input Voltage VIL Low Level Input Voltage VOH High Level Output Voltage VOL Low Level Output Voltage Min. 1.8 1.8 1.8 Max. 0.7VCC 1.8 to 2.3 1.8 Un it -40 to 85 o C V CC (V) V 0.2VCC VI = VIH or VIL IO=-100 µA VCC-0.2 IO=-6 mA 1.4 VI = VIH or VIL IO=100 µA 0.2 IO=6 mA 0.3 V V V Input Leakage Current 1.8 VI = 0 to 3.6 V ±5 µA IOZ 3 State Output Leakage Current 1.8 VI = VIH orVIL VO = 0 to 3.6V ±10 µA Ioff Power Off Leakage Current 0 VI orVO = 0 to 3.6V 10 µA ICC Quiescent Supply Current VI = VCC orGND 20 VI orVO = VCC to 3.6 V ±20 µA II 1.8 DYNAMIC SWITCHING CHARACTERISTICS (Ta = 25oC, Input tr = tf = 2.0ns, CL = 30pF, RL = 500Ω) Symb ol Parameter Test Con dition s T A = 25 C VOLV Min . 1.8 3.3 0.8 Dynamic Low Voltage Quiet Output (note 1, 3) 1.8 -0.25 2.5 VIL = 0 V VIH = VCC VIL = 0 V VIH = VCC 3.3 VOHV T yp. Dynamic Low Voltage Quiet Output (note 1, 3) 2.5 Dynamic High Voltage Quiet Output (note 2, 3) 1.8 2.5 3.3 Un it o V CC (V) VOLP Value Max. 0.25 0.6 -0.6 V V -0.8 VIL = 0 V VIH = VCC 1.5 1.9 V 2.2 1) Number ofoutputs defined as ”n”. Measured with”n-1” outputs switching from HIGH to LOW or LOW t o HIGH. The remaining output is measured in the LOW state. 2) Number ofoutputs defined as ”n”. Measured with”n-1” outputs switching from HIGH to LOW or LOW t o HIGH. The remaining output is measured in the HIGH state. 3) Parameters guaranteed by design. 5/11 74VCX16374 AC ELECTRICAL CHARACTERISTICS (CL = 30 pF, RL = 500 Ω, Input tr = tf = 2.0 ns) Symb ol Parameter V CC (V) tPLH tPHL Propagation Delay Time CK to Qn tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time ts th tw fMAX tOSLH tOSHL Setup Time, HIGH or LOW level Dn to CK Hold Time, HIGH or LOW level Dn to CK CK Pulse Width, HIGH Clock Pulse Frequency Output to Output Skew Time (note 1, 2) Test Con dition Waveform 1.8 2.3 to 2.7 Value -40 to 85 o C Min. Max. 1.5 7.8 1.0 3.9 3 3.0 to 3.6 1.8 2.3 to 2.7 3.0 to 3.6 1.8 2.3 to 2.7 3.0 to 3.6 0.8 1.5 1.0 0.8 1.5 1.0 0.8 2 2 1.8 2.3 to 2.7 2.5 1.5 1 3.0 to 3.6 1.8 2.3 to 2.7 3.0 to 3.6 1.8 2.3 to 2.7 3.0 to 3.6 1 ns ns ns ns 100 200 250 1 ns ns 1.5 1.0 1.0 1.0 4.0 1.5 1.5 1 1.8 2.3 to 2.7 3.0 to 3.6 1.8 2.3 to 2.7 3.0 to 3.6 3.0 9.2 4.6 3.5 6.8 3.8 3.5 Un it MHz 0.75 0.5 0.5 ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any twooutputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tpHLn|) CAPACITIVE CHARACTERISTICS Symb ol Parameter Test Co nditi ons Valu e Min. T yp. Input Capacitance 1.8, 2.5 or 3.3 VIN = 0V or VCC 6 COUT Output Capacitance 1.8, 2.5 or 3.3 VIN = 0V or VCC 7 CPD Power Dissipation Capacitance (note 1) 1.8, 2.5 or 3.3 fIN = 10MHz VIN = 0V or VCC 20 CIN Un it T A = 25 oC V CC (V) Max. pF pF pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. Average operting current can be obtained by the following equation. I CC(opr) = CPD • VCC • fIN + ICC/16 (per circuit) 6/11 74VCX16374 TEST CIRCUIT T EST SW IT CH tPLH , tPHL Open tPZL , tPLZ (VCC = 3.0 to 3.6V) 6V tPZL , tPLZ (VCC = 2.3 to 2.7V or 1.8V) 2VCC tPZH , tPHZ GND CL = 30 pF or equivalent (includes jigand probe capacitance) RL = R1 = 500Ω orequivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM SYMBOL VALUES Symbol VIH V CC 3.0 to 3.6V 2.3 to 2.7V 1.8V 2.7V VCC VCC VM 1.5V VCC/2 VCC/2 VX VOL + 0.3V VOL + 0.15V VOL + 0.15V VY VOH - 0.3V VOH - 0.15V VOH - 0.15V 7/11 74VCX16374 WAVEFORM 1: PROPAGATION DELAYS, SETUP AND HOLD TIMES (f=1MHz; 50% duty cicle) 8/11 74VCX16374 WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIMES (f=1MHz; 50% duty cicle) WAVEFORM 3: PULSE WIDTH 9/11 74VCX16374 TSSOP48 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. A MIN. 1.1 MAX. 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.5 12.6 0.408 0.492 0.496 E 7.95 8.1 8.25 0.313 0.319 0.325 E1 6.0 6.1 6.2 0.236 0.240 0.244 e 0.5 BSC 0.0197 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b K e E1 PIN 1 IDENTIFICATION 1 L E c D 10/11 TYP. 74VCX16374 Information furnished is believed to be accurate and reliable. However, STMicroelectronic s assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com . 11/11