Astec Integrated Power 240 Watts AK80A Total Power: Input Voltages: No. of Outputs: 240 Watts 24V Single Electrical Specs Input Input Range 18 to 36 VDC Efficiency 83% typical (5V @ 40A); 87% typical (12V @ 18A); 87% typical (15V @ 16A) Output Load Regulation Line Regulation Noise/Ripple Remote sense Output Voltage Adjust Range Transient Response Special Features • High efficiency - up to 87% • 500 KHz fixed frequency • 85°C baseplate operating temperature (with no derating) • Low output ripple and noise • Excellent transient response • High reliability - over 1 million hours MTBF • Wide input voltage range • TTL compatible enable control • Parallelable • Adjustable output voltage and current limit • Temperature monitor output • Overtemperature and short circuit protection • Regulation to zero load Environmental Operating temperature (baseplate): 0.3% typical down to no load 0.1% typical 100 mV typical (output below 5V) 2% typical (output 5V and over) Up to 0.5V Current Share Accuracy Overvoltage Protection Current Limit ±10% of nominal output 10% typical deviation with 300µs recovery (25-75% full load) 5% typical 130% nominal Vo 115% Io max Control Voltage Adjust Enable Current Limit Adjust Clock Input (external sync) Clock Output (internal clock) Power Good/Identification Temperature Monitor Output 90 to 110% Vo TTL compatible (low to enable) 20 to 100% Io rated 3.5 to 5Vp-p @ 1MHz ± 10% 4.4 to 5.5Vp-p @ 1MHz ± 0.5% High (Vo) = power good 10 mV/°K (2.73V = 0°C) Notes 0°C to +85°C Nominal values apply with sense pins connected and other control pins unconnected. Storage temperature: -40°C to +105°C Specifications subject to change without notice. Overtemperature protection: 90°C typical MTBF: > 1 million hours (50°C baseplate) Safety UL CSA VDE EN CE 52 UL 1950 E132002 CSA22.2-234 LR53982C CSA22.2-950 IEC950 20366-3336-1002 & 1008 60950 CEMark (LVD) North America (USA): 1-888-41-ASTEC Europe (UK): 44 (1384) 842-211 Asia (HK): 852-2437-9662 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 AK80A Ordering Information Input Voltage Output Voltage Output Current Model Number 24V 24V 24V 24V 3.3V 5V 12V 15V 40A 30A 14A 12A AK80A-024L-033F40 AK80A-024L-050F30 AK80A-024L-120F14 AK80A-024L-150F12 24V 24V 8A AK80A-024L-240F08 Please contact Astec for information on other output voltages, power ranges and configurations. Pin Assignments 31. +ve 32. –ve 21. +ve 22. +ve 23. +ve 24. +ve 26. -ve 27. -ve 28. -ve 29. -ve 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. +SENSE PG/ID V ADJ -SENSE S COM C SHARE CLK OUT CLK IN ENABLE C LIM ADJ TEMP MON PRI AUX 12.7 (0.50) Control Pins 8 PRIMARY SIDE CONTROL PINS 8 OUTPUT PINS 4 SECONDARY SIDE CONTROL PINS 2 INPUT PINS Secondary side controls 32 Primary side controls 31 9 12 8 5 3 4 2 1 29 28 27 26 24 23 22 21 61.0 (2.40) Output AMPSS™ POWER MODULE Input THERMAL BASE PLATE* 116.8 (4.60) + O/P C SHARE CLK OUT 5 9 S COM 2 1 + SENSE Load 3 4 – SENSE 12 Temperature monitor output (e.g. to fan control circuit) ENABLE PG/ID goes high (to Vo) to indicate power good. Resistance between PG/ID and +O/P with no power applied indicates nominal O/P voltage, where 1K Ohm = 1 volt (eg 3K3 = 3.3 V). – O/P 18 to 36V or 36 to 72V C SHARE CLK IN 5 8 S COM 9 12 2 1 + SENSE + O/P + I/P 8 5 9 12 2 1 + SENSE Load – I/P 3 4 – SENSE – O/P 3 4 – SENSE ENABLE Enable (close to enable) Astec Integrated Power 8 Output voltage adjust Current limit adjust www.astec.com 53