CDP68HC68P1 CMOS Serial 8-Bit Input/Output Port October 2000 Features Description • Fully Static Operation The CDP68HC68P1 is a serially addressed 8-bit Input/Output port that allows byte or individual bit control. It consists of three registers, an output buffer and control logic. Data is shifted in and out of the device via shift register that utilizes the SPI (Serial Peripheral Interface) bus. The I/O port data flow is controlled by the Data Direction Register and data is stored in the Data Register that outputs or senses the logic levels at the buffered I/O pins. All inputs, including the serial interface are Schmitt triggered. This device also features a compare function that compares the data register and port pin values for 4 programmable conditions and sets a software accessible flag if the condition is satisfied. The user also has the option of bit-set or bit-clear when writing to the data register. • Operating Voltage Range 3-6V • Compatible with Intersil/Motorola SPI Bus • 2 External Address Pins Tied to VDD or VSS to Allow Up to 4 Devices to Share the Same Chip Enable • Versatile Bit-Set and Bit-Clear Capability • Accepts Either SCK Clock Polarity - SCK Voltage Level is Latched When Chip Enable Goes Active • All Inputs are Schmitt-Trigger • 8-Bit I/O Port - Each Bit can be Individually Programmed as an Input or Output Via an 8-Bit Data Direction Register Ordering Information • Programmable On Board Comparator • Simultaneous Transfer of Compare Information to CPU During Read or Write - Separate Access Not Required PART NUMBER TEMP. RANGE (oC) PKG. NO. PACKAGE CDP68HC68P1E -55 to 85 16 Ld PDIP E16.3 CDP68HC68P1M -55 to 85 16 Ld SOIC M16.15 CDP68HC68P1D -55 to 125 16 Ld SBDIP D16.3 Pinout CDP68HC68P1 (PDIP, SOIC, SBDIP) (D, E, M, SUFFIX) TOP VIEW ID0 1 16 VDD ID1 2 15 D1 MISO 3 14 D2 MOSI 4 13 D3 SCK 5 12 D4 CE 6 11 D5 DO 7 10 D6 VSS 8 9 D7 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 2000 1 File Number 1858.2 CDP68HC68P1 MOSI MISO SHIFT REGISTER CE SCK ID1 ID0 CONTROL LOGIC COMPARATOR DIRECTION REGISTER DIRECTION REGISTER INPUT/OUTPUT D0 - D7 FIGURE 1. SINGLE PORT I/O BLOCK DIAGRAM CHIP ENABLE CE DATA IN MOSI DATA OUT MISO CLOCK CDP68HC68P1 I/O PORT DATA IN/OUT D0 - D7 SCK ID0 CHIP ID1 IDENTIFY FIGURE 2. SINGLE PORT I/O Pin Description ID0 1 16 VDD ID1 2 15 D1 MISO 3 14 D2 MOSI 4 13 D3 SCK 5 12 D4 CE 6 11 D5 DO 7 10 D6 VSS 8 9 D7 MOSI - Master-out, Slave in pin. Data bytes are shifted in at this pin most significant bit first. This pin will retain its previous logic state if its driving line becomes Hi-Z. SCK - Serial clock input. This input causes serial data to be latched from the MOSI input and shifted out on the MISO output. CE - A negative chip enable input. A high to low transition on this pin latches the inactive SCK polarity and compare flag and indicates the start of a data transfer. The serial interface logic is enabled only when CE is low. This pin will retain its previous logic state if its driving line becomes Hi-Z. ID0, ID1 - Chip identify pins, normally tied to VDD to VSS. The 4 possible combinations of these pins allow 4 I/Os to share a common chip enable. When the levels at these pins match those of the identify bits in the control word, the serial bus is enabled. The chip identify pins will retain their previous logic state if the lines driving them become Hi-Z. D0 -D7 - I/O Port pins. Individual programmable inputs or outputs. VDD and VSS - Positive and negative power supply line. All pins except the power supply lines and MISO have Schmitt-trigger buffered inputs. MISO - Master-in, Slave out pin. Data bytes are shifted out at this pin most significant bit first. When the chip enable signal is high, this pin is Hi-Z. 2 CDP68HC68P1 Absolute Maximum Ratings Thermal Information DC Supply Voltage Range, (VDD) . . . . . . . . . . . . . . . . -0.5V to +7V (Voltage Referenced to VSS Terminal) Input Voltage Range, All Inputs . . . . . . . . . . . . . -0.5V to VDD +0.5V DC Input Current, Any One Input. . . . . . . . . . . . . . . . . . . . . . . . .±10mA Power Dissipation Per Package (PD) TA = -40oC to 60oC (Package Type E) . . . . . . . . . . . . . . . 500mW TA = 60oC to 85oC (Package Type E) Derate Linearly at . . . . . . . . . . . . . . . . . . . . . 12mW/oC to 200mW TA = -55oC to 100oC (Package Type D) . . . . . . . . . . . . . . 500mW TA = 100oC to 125oC (Package Type D) Derate Linearly at . . . . . . . . . . . . . . . . . . . . . . 2mW/oC to 200mW TA = -40oC to 60oC (Package Type M) (Note 1) . . . . . . . . 300mW TA = 60oC to 85oC (Package Type M) (Note 1) Derate Linearly at . . . . . . . . . . . . . . . . . . . . . . 5mW/oC to 175mW Thermal Resistance (Typical, Note 2) θJA (oC/W) θJC (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . 90 NA SOIC Package . . . . . . . . . . . . . . . . . . . 160 NA SBDIP Package . . . . . . . . . . . . . . . . . . 85 22 Device Dissipation Per Output Transistor . . . . . . . . . . . . . . . 100mW TA = Full Package Temperature Range (All Package Types) Maximum Storage Temperature Range (TSTG) . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) At Distance 1/16in ± 1/32in. (1.59 ± 0.79mm) . . . . . . . . . . . 265oC (SOIC - Lead Tips Only) Operating Conditions For maximum reliability, operating conditions should be selected so that operation is always within the following ranges: Temperature Range (TA) Package Type D . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Package Type E, M . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 85oC DC Operating Voltage Range . . . . . . . . . . . . . . . . . . 3V Min, 6V Max Serial Clock Frequency, fSCK, VDD = 3V . . . . . . . . . . 1.05MHz Max Serial Clock Frequency, fSCK, VDD = 4.5V. . . . . . . . . . 2.1MHz Max Input Voltage Range, VIH . . . . . . . . . . . . . . . . . . . . VDD +0.3V Max Input Voltage Range, VIL . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V Min CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Printed circuit board mount: 57mm x 57mm minimum area x 1.6mm thick G10 epoxy glass, or equivalent. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Static Electrical Specifications PARAMETER Output Voltage TA = -40oC to 85oC, VDD = 3.3V ±10%, Unless Otherwise Specified. TEST CONDITIONS SYMBOL MIN (NOTE 3) TYP MAX UNITS VOH IOH = -0.4mA, VDD = 3V 2.7 - - V VOL IOL = 0.4mA, VDD = 3V - - 0.3 V Input Voltage D0 - D7 Positive Trigger Threshold VP 1.85 - 2.4 V Negative Trigger Threshold VN 0.85 - 1.35 V Hysteresis VIH 0.85 - 1.25 V ID0, ID1, MOSI, SCK, CE Positive Trigger Threshold VP 1.3 - 1.9 V Negative Trigger Threshold VN 0.8 - 1.2 V Hysteresis VIH 0.5 - 0.95 V IIN - - ±1 µA Standby Device Current IDDS - 1 15 µA Three-State Output Leakage Current IOUT - - ±10 µA VIN = VIL, VIH - 0.1 1 mA VIN = 0V, f = 1MHz, TA = 25oC - 4 6 pF Input Voltage Input Leakage Current Operating Device Current (Note 4) Input Capacitance IOPER CIN NOTES: 3. Typical values are for TA = 25oC and nominal VDD. 4. Outputs open circuited; cycle time = Min. tCYCLE, duty = 100%. 3 CDP68HC68P1 Static Electrical Specifications PARAMETER Output Voltage At TA = -40oC to 85oC, VDD = 5V ±10%, Unless Otherwise Specified. TEST CONDITIONS SYMBOL MIN (NOTE 5) TYP MAX UNITS VOH IOH = -1.6mA, VDD = 4.5V 3.7 - - V VOL IOL = 1.6mA, VDD = 4.5V - - 0.4 V VOH IOH ≤ 20µA, VDD = 4.5V 4.4 - - V VOL IOL ≤ 20µA, VDD = 4.5V - - 0.1 V Input Voltage D0 - D7 Positive Trigger Threshold VP 2.15 - 3.05 V Negative Trigger Threshold VN 1.35 - 2 V Hysteresis VIH 0.8 - 1.2 V ID0, ID1, MOSI, SCK, CE Positive Trigger Threshold VP 3.15 - 3.85 V Negative Trigger Threshold VN 1.7 - 2.25 V Hysteresis VIH 1.3 - 1.7 V IIN - - ±1 µA Standby Device Current IDDS - 1 15 µA Three-State Output Leakage Current IOUT - - ±10 µA VIN = VIL, VIH - 0.2 2 mA VIN = 0V, f = 1MHz, TA = 25oC - 4 6 pF Input Voltage Input Leakage Current Operating Device Current (Note 6) Input Capacitance IOPER CIN NOTES: 5. Typical values are for TA = 25oC and nominal VDD. 6. Outputs open circuited; cycle time = Min, tCYCLE, duty = 100%. VDD ±10%, VSS = 0V DC, TA = -40oC to 85oC, CL = 200pF. See Figures 8 and 9. Dynamic Electrical Specifications - Bus Timing VDD = 3.3V VDD = 5V SYMBOL MIN MAX MIN MAX UNITS Chip Enable Set-Up Time tEVCV 200 - 100 - ns Chip Enable after Clock Hold Time tCVEX 250 - 125 - ns Clock Width High tWH 400 - 200 - ns Clock Width Low tWL 400 - 200 - ns Data In to Clock Set-Up Time tDVCV 200 - 100 - ns Data In after Clock Hold Time tCVDX 200 - 100 - ns Clock to Data Propagation Delay tCVDV - 200 - 100 ns Chip Disable to Output High Z tEXQZ - 200 - 100 ns Output Rise Time tr - 200 - 100 ns Output Fall Time tf - 200 - 100 ns tCVQX - 200 - 100 ns tREC 200 - 200 - ns PARAMETER Clock to Data Out Archive Clock Recovery Time 4 CDP68HC68P1 Waveforms MISO HI Z C07 COMPARE FLAG C06 D7 D6 D0 HI Z tr, tf MOSI X C07 C06 C05 C04 C00 tDVCV D7 D6 D0 X tDVCV tCVDX tCVDX CE tWL tWH tREC tCVEX SCK tEVCV FIGURE 3. PORT-PIN DATA CHANGES MOSI X MISO C07 C06 HI Z C05 C04 C07 C06 C00 X COMPARE FLAG D7 D6 tCVQX D0 HI Z tEXQZ tCVDV CE tWL tREC tWH tCVEX SCK tEVCV FIGURE 4. READ CYCLE TIMING WAVEFORMS Introduction CE The single port I/O is serially accessed via the synchronous SPI bus. It features 8 data pins that are programmed as inputs or outputs. Serial access consists of a two-byte operation. The first byte shifted in is the control byte that configures the device. The second byte transferred is the data byte that is read from or written to the data register or data direction register. This data byte can also be programmed to act as a mask to set or clear individual bits. SHIFT INTERNAL STROBE SCK (CPOL = 1) CE SHIFT INTERNAL STROBE Functional Description SCK (CPOL = 0) MOSI OR MISO MSB The single port I/O consists of three byte-wide registers, (data direction, data and shift) an input/output buffer and control logic circuitry (See Figure 1). Data is transferred between the I/O data and data direction registers via the shift register. Once the I/O port is selected, the first byte shifted in to the shift register is the control byte that selects the register (the Data or Data direction register), determines data transfer direction (read or write) and sets the compare feature and function (mask or data) of the byte immediately MSB - 1 NOTE: CPOL and CPHA are bits in the CDP68HC05C4B and CDP68HC05C16B MCU control register and determine inactive clock polarity and phase. CPHA must always equal 1. FIGURE 5. DATA TRANSFERS UTILIZING CLOCK INPUT 5 CDP68HC68P1 following the control byte, the data byte (See Addressing the Single Port I/O). Each bit of the data register may be individually programmed as an input or output. A logic low in a data direction bit programs that pin as an input, a logic high makes it an output. A read operation of data register pins programmed as inputs reflects the current logic level present at the buffered port pins. A read operation of those data register pins programmed as outputs indicates the last value written to that location. At power-up, all port pins are configured as unterminated inputs. Two chip identify pins are used to allow up to 4 I/O ports to share the same chip enable signal. The first two bits shifted in are compared with the hardwired levels at the chip identify pins to enable the selected I/O for serial data transfer. Note that when chip enable becomes true, the compare flag is latched for all devices sharing the same chip enable. Byte. As shown in Table 1, the values for CM1 and CM0 will sense one of four separate conditions. Compare Function Data Format The value of a port pin (D0 - D7), configured as an input, is compared with the corresponding bit value (DR0 - DR7) stored in the Data Register. Pins configured as outputs are assumed to have the same value as the corresponding bit stored in the Data Register. The compare function is programmed via C01 and C00 (CM1, CM0) of the Address During write operations, the data byte that follows the control byte is normally the data word that is transferred to the data or data direction register. Control bits 2 and 3 (DF0 and DF1) change the interpretation of this data as shown in Table 2. Note that one or more bits can be set or cleared in either register without having to write to bits not requiring change. The compare flag is set to one when the programmed condition is satisfied. Otherwise, the flag is cleared to zero. The compare flag is latched when the device is enabled (a transition of CE from “High” to “Low”). TABLE 1. CM1 CM0 CONDITION 0 0 At least one non-match 0 1 All match 1 0 All are non-match 1 1 At least one match TABLE 2. C03 DF1 C02 DF0 0 X Data following the control word will be written to the selected register. 1 0 Data following the control word is a mask. Those bits which are a 1 will cause that register flip-flop to be cleared to 0. Those which are a 0 will cause that register flip-flop to be unchanged. 1 1 Data following the control word is a mask. Those bits which are a 1 will cause that register flip-flop to be set to 1; those which are a 0 will cause that register flip-flop to be unchanged. OPERATION TABLE 3. EXAMPLE DATA PREVIOUS REGISTER VALUE NEW REGISTER VALUE C07 C06 C05 1 0 X C01 C00 11110000 10101010 11110000 C07 C06 C05 1 1 1 C01 C00 11110000 10101010 11111010 C07 C06 C05 1 1 0 C01 C00 11110000 10101010 00001010 C07 C06 C05 1 1 X C01 C00 00000000 10101010 10101010 CONTROL X = Don’t Care CE SCK OR SCK MOSI X C07 C06 C05 C04 C03 C02 C01 C01 INPUT MISO Z Z Z C07 C06 C05 C04 X = DON’T CARE Z = HIGH IMPEDANCE * = COMPARE FLAG FIGURE 6. CONTROL BYTE 6 C03 * OUTPUT CDP68HC68P1 Addressing the Single Port I/O C04 (R/W): Read/Write. Low when data is to be transferred from the SPI I/O to the CPU (read) and high when the I/O is receiving data from the CPU (write). The Serial Peripheral Interface (SPI) utilized by the I/O Port is a serial synchronous bus for control and data transfers. It consists of a SCK clock input pin that shifts data out of the I/O port (MISO, MASTER IN, SLAVE OUT) and latches data presented at the input pin, MOSI (master out, slave in). Data is transferred most significant bit first. There is one SCK clock for each bit transferred and bits are transferred in groups of eight. C03 (DF1), C02 (DF0): Data Format Bits. These have meaning only when R/W is high. During a write operation, DF1 and DF0 control how the byte following the control word is interpreted. See Data Format. C01 (CM1), C00 (CM0): Compare Mode Select. These bits select one of four events which will set the internal Condition Flag. See Compare Operation. When the I/O port is selected by bringing the chip enable pin low, the logic level at the SCK input is sampled to determine the internal latching and shift polarity for input and output signals on the SPI. (See Figure 3). Read Operation The first byte shifted in when the chip is selected is always the control byte followed by one or more bytes that become data or a mask for the data and data direction register. As the control byte is being shifted in one the MOSI line, data on the MOSI line shifts out. (See Figure 4). 7 6 5 4 3 2 1 0 ID1 ID0 RS R/W DF1 DF0 CM1 CM0 During a read operation, the CPU transfers data from the I/O by first sending a control byte on the MOSI line while the chip-selected I/O sends compare information followed by one or more data bytes on the MISO line. The selected register will be continuously read if CE is held low after the first data byte is shifted out. Write Operation C07 (ID1), C06 (ID0): Chip-Identify bits. During a write operation, the data byte follows the control byte for the selected register. While this byte is being shifted in, old data from that register is shifted out. If CE remains low after the data byte is shifted in, MISO becomes high impedance and the new data is placed in the selected register. At the time the eighth data bit is strobed into the data pins (D0 - D7) will change as indicated in Figure 7. C05 (RS): Register Select. When RS is low, the data register is selected. When RS is high, the Direction Register is selected. CE MOSI MISO Z C07 C06 C05 0 C03 C02 C01 C00 X X X X X X X X Z Z C07 C06 C05 0 C03 * 8-BIT DATA WORD X = DON’T CARE Z = HIGH IMPEDANCE * = COMPARE FLAG FIGURE 7. READ BYTES CE MOSI MISO Z C07 C06 C05 1 C03 C02 C01 C00 8-BIT DATA WORD Z Z C07 C06 C05 1 C03 * PREVIOUS 8-BIT WORD Z = HIGH IMPEDANCE * = COMPARE FLAG FIGURE 8. READ BYTES MOSI D3 D2 D1 D0 SCK D0 - D7 PREVIOUS FIGURE 9. PORT-PIN DATA CHANGES 7 NEW CDP68HC68P1 Ceramic Dual-In-Line Metal Seal Packages (SBDIP) D16.3 MIL-STD-1835 CDIP2-T16 (D-2, CONFIGURATION C) 16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE LEAD FINISH c1 -A- -DBASE METAL E SYMBOL b1 M (b) M -Bbbb S C A - B S INCHES (c) SECTION A-A D S D BASE PLANE Q S2 -C- SEATING PLANE A L S1 eA A A b2 b e ccc M C A - B S D S eA/2 c NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. 5. Dimension Q shall be measured from the seating plane to the base plane. 6. Measure dimension S1 at all four corners. 7. Measure dimension S2 from the top of the ceramic body to the nearest metallization or lead. 8. N is the maximum number of terminal positions. 9. Braze fillets shall be concave. 10. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 11. Controlling dimension: INCH. MILLIMETERS MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.840 - 21.34 - E 0.220 0.310 5.59 7.87 - e aaa M C A - B S D S MIN 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 5 S1 0.005 - 0.13 - 6 S2 0.005 - 0.13 - 7 α 90o 105o 90o 105o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2 N 16 16 8 Rev. 0 4/94 8 CDP68HC68P1 Dual-In-Line Plastic Packages (PDIP) E16.3 (JEDEC MS-001-BB ISSUE D) N 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AD E BASE PLANE -C- A2 SEATING PLANE A L D1 e B1 D1 B 0.010 (0.25) M A1 eC C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8, 10 eA C 0.008 0.014 C D 0.735 0.775 D1 0.005 - E 0.300 0.325 E1 0.240 0.280 6.10 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 9 e 0.100 BSC eA 0.300 BSC eB - L 0.115 N 16 0.204 0.355 18.66 - 19.68 5 0.13 - 5 7.62 8.25 6 7.11 5 2.54 BSC - 7.62 BSC 6 0.430 - 0.150 2.93 16 10.92 7 3.81 4 9 Rev. 0 12/93 CDP68HC68P1 Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) N INDEX AREA H 0.25(0.010) M 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M E INCHES -B- 1 2 SYMBOL 3 L SEATING PLANE -A- h x 45o A D -C- e α B 0.25(0.010) M C 0.10(0.004) C A M B S NOTES: 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. MAX MILLIMETERS MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e A1 MIN 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α 16 0o 16 8o 0o 7 8o Rev. 0 12/93 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 10 ASIA Intersil Ltd. 8F-2, 96, Sec. 1, Chien-kuo North, Taipei, Taiwan 104 Republic of China TEL: 886-2-2515-8508 FAX: 886-2-2515-8369