ETC LN533RAMRS(LNM233AS02)

Numeric Display
3 Digit 8.0mm (.3”) Series
12 11 10 9
7
a
f D1
e
g
D2
b
D3
c
dp
d
1
2
3
4
Red
Red
Green
Green
4.0
5
6
7.0
10°
Assignment
Common Anode D1
Common Cathode D1
3
Cathode d
Anode d
4
Common Anode D2
Common Cathode D2
5
Common Anode D3
Common Cathode D3
6
Cathode dp
Anode dp
7
Cathode b
Anode b
8
Cathode f
Anode f
9
Cathode a
Anode a
10
Cathode e
Anode e
11
Cathode g
Anode g
12
No Pin
No Pin
3 – φ 1.0
2.5
Anode c
2
*9.20
0.65
1.0
Pin
Assignment
No.
1
Cathode c
8
7.0
3.5
LN533RAMRS ········· LNM233AS02 ··········
LN533RKMRS ········· LNM233KS02 ··········
LN533GAMGS ········· LNM333AS02 ··········
LN533GKMGS ········· LNM333KS02 ··········
Terminal Connection
21.0 +− 00.35
Lighting Color
13.0
8.0
1.0
Global Prat No.
5.0 +− 1.0
0.5 6.5
0.75
Conventional Part No.
Unit: mm
0.75
1.5
11 – φ 0.45
*2.54
2.54 × 5.0 = 12.7
Lead wire dimension
■ Absolute Maximum Ratings (Ta = 25°C)
Lighting Color
Red
Green
IFP(mA)∗
65
65
VR(V)
5
5
IO
IO /d.p
IF
Typ Min Typ
5
70
70
200
5
70
70
200
10
1000 300 300
10
1000 300 300
µcd µcd µcd mA
VF
Typ Max
2.03 2.8
2.03 2.8
2.03 2.8
2.03 2.8
V
V
PD(mW)
34
34
IF(mA)
12
12
Topr(°C)
−25 ∼ +80
−25 ∼ +80
Tstg(°C)
−30 ∼ +85
−30 ∼ +85
Pulse width 1 msec. The condition of IFP is duty 10%, Pulse width 1 msec
■ Electro−Optical Characteristics (Ta = 25°C)
Conventional
Part No.
LN533RAMRS
LN533RKMRS
LN533GAMGS
LN533GKMGS
Unit
Lighting
Color
Red
Red
Green
Green
−
Common
Anode
Cathode
Anode
Cathode
−
IO  IF
λP
Typ
700
700
565
565
nm
∆λ
Typ
100
100
30
30
nm
IF  VF
10000
IF
10
10
10
10
mA
IR
Max
10
10
10
10
µA
VR
5
5
5
5
V
IF  T a
100
3000
30
1000
500
S
MR S
RA MR
3
53 RA
LN 533
LN
300
100
1
3
5
10
30
Forward Current
20
Forward Current
50
Forward Current
5000
L
LN N5
53 33G
3G A
KM MG
GS S
Luminous Intensity
25
10
5
3
50
100
1
15
10
5
0
1.6
1.8
2.0
2.2
Forward Voltage
2.4
0
20
40
60
80
100
Ambient Temperature
313
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.
Please read the following notes before using the datasheets
A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may appear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.
2001 MAR