ETC NL74VCXH16373DT

NL74VCXH16373
Low-Voltage 1.8/2.5/3.3V
16-Bit Transparent Latch
With 3.6V–Tolerant Inputs and Outputs
(3–State, Non–Inverting)
The NL74VCXH16373 is an advanced performance, non–inverting
16–bit transparent latch. It is designed for very high–speed, very
low–power operation in 1.8V, 2.5V or 3.3V systems. The VCX16373
is byte controlled, with each byte functioning identically, but
independently. Each byte has separate Output Enable and Latch
Enable inputs. These control pins can be tied together for full 16–bit
operation.
When operating at 2.5V (or 1.8V) the part is designed to tolerate
voltages it may encounter on either inputs or outputs when interfacing
to 3.3V busses. It is guaranteed to be over–voltage tolerant to 3.6V.
The NL74VCXH16373 contains 16 D–type latches with 3–state
3.6V–tolerant outputs. When the Latch Enable (LEn) inputs are
HIGH, data on the Dn inputs enters the latches. In this condition, the
latches are transparent, (a latch output will change state each time its D
input changes). When LE is LOW, the latch stores the information that
was present on the D inputs a setup time preceding the
HIGH–to–LOW transition of LE. The 3–state outputs are controlled
by the Output Enable (OEn) inputs. When OE is LOW, the outputs are
enabled. When OE is HIGH, the standard outputs are in the high
impedance state, but this does not interfere with new data entering into
the latches. The data inputs include active bushold circuitry,
eliminating the need for external pull–up resistors to hold unused or
floating inputs at a valid logic state.
• Designed for Low Voltage Operation: VCC = 1.65–3.6V
• 3.6V Tolerant Inputs and Outputs
• High Speed Operation: 3.0ns max for 3.0 to 3.6V
•
•
•
http://onsemi.com
48
1
TSSOP–48
DT SUFFIX
CASE 1201
MARKING DIAGRAM
48
NL74VCXH16373DT
AWLYYWW
1
A
WL
YY
WW
= Assembly Location
= Wafer Lot
= Year
= Work Week
PIN NAMES
3.9ns max for 2.3 to 2.7V
6.8ns max for 1.65 to 1.95V
Static Drive: ±24mA Drive at 3.0V
±18mA Drive at 2.3V
±6mA Drive at 1.65V
Supports Live Insertion and Withdrawal
Includes Active Bushold to Hold Unused or Floating Inputs at a Valid
Logic State
IOFF Specification Guarantees High Impedance When VCC = 0V†
•
• Near Zero Static Supply Current in All Three Logic States (20µA)
Substantially Reduces System Power Requirements
• Latchup Performance Exceeds ±300mA @ 125°C
• ESD Performance: Human Body Model >2000V; Machine Model
Pins
Function
OEn
LEn
D0–D15
O0–O15
Output Enable Inputs
Latch Enable Inputs
Inputs
Outputs
ORDERING INFORMATION
Package
Shipping
NL74VCXH16373DT
Device
TSSOP
39 / Rail
NL74VCXH16373DTR
TSSOP
2500 / Reel
>200V
†NOTE: To ensure the outputs activate in the 3–state condition, the output
enable pins should be connected to VCC through a pull–up resistor. The
value of the resistor is determined by the current sinking capability of the
output connected to the OE pin.
 Semiconductor Components Industries, LLC, 2000
May, 2000 – Rev. 0
Powered by ICminer.com Electronic-Library Service CopyRight 2003
1
Publication Order Number:
NL74VCXH16373/D
NL74VCXH16373
OE1 1
48 LE1
O0 2
47 D0
O1 3
46 D1
GND 4
45 GND
O2 5
44 D2
O3 6
43 D3
VCC 7
O4 8
42 VCC
41 D4
O5 9
OE1
LE1
D0
D1
40 D5
GND 10
39 GND
O6 11
38 D6
O7 12
37 D7
O8 13
36 D8
O9 14
35 D9
GND 15
D2
D3
34 GND
O10 16
33 D10
O11 17
32 D11
VCC 18
O12 19
31 VCC
30 D12
O13 20
29 D13
GND 21
28 GND
O14 22
27 D14
O15 23
26 D15
OE2 24
25 LE2
D4
D5
D6
D7
1
OE2
48
LE2
nLE
47
D
nLE
46
D
nLE
44
D
nLE
43
D
nLE
41
D
nLE
40
D
nLE
38
D
nLE
37
D
Figure 1. 48–Lead Pinout
(Top View)
25
O0
36
D8
3
Q
O1
35
D9
5
Q
O2
33
D10
6
Q
O3
32
D11
8
Q
O4
30
D12
9
Q
O5
29
D13
11
Q
O6
27
D14
12
Q
O7
26
D15
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
nLE
D
13
Q
14
Q
16
Q
17
Q
19
Q
20
Q
22
Q
23
Q
O8
O9
O10
O11
O12
O13
O14
O15
Figure 2. Logic Diagram
1
OE1 48
LE1
25
LE2 24
OE2
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
Inputs
2
Q
24
47
46
44
43
41
40
38
37
36
35
33
32
30
29
27
26
EN1
EN2
EN3
EN4
1
1∇
1
2∇
1
3∇
1
4∇
Outputs
2
3
5
6
8
9
11
12
13
14
16
17
19
20
22
23
O0
O1
O2
O3
O4
O5
O6
O7
O8
O9
O10
O11
O12
O13
O14
O15
Inputs
Outputs
LE1
OE1
D0:7
O0:7
LE2
OE2
D8:15
O8:15
X
H
X
Z
X
H
X
Z
H
L
L
L
H
L
L
L
H
L
H
H
H
L
H
H
L
L
X
O0
L
L
X
O0
H = High Voltage Level; L = Low Voltage Level; Z = High Impedance State; X = High or Low Voltage Level and Transitions Are Acceptable, for
ICC reasons, DO NOT FLOAT Inputs. O0 = No Change.
http://onsemi.com
2
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373
ABSOLUTE MAXIMUM RATINGS*
Symbol
Parameter
VCC
DC Supply Voltage
VI
VO
Value
Condition
Unit
–0.5 to +4.6
V
DC Input Voltage
–0.5 ≤ VI ≤ +4.6
V
DC Output Voltage
–0.5 ≤ VO ≤ +4.6
Output in 3–State
V
–0.5 ≤ VO ≤ VCC + 0.5
Note 1.; Outputs Active
V
IIK
DC Input Diode Current
–50
VI < GND
mA
IOK
DC Output Diode Current
–50
VO < GND
mA
+50
VO > VCC
mA
IO
DC Output Source/Sink Current
±50
mA
ICC
DC Supply Current Per Supply Pin
±100
mA
IGND
DC Ground Current Per Ground Pin
±100
mA
TSTG
Storage Temperature Range
–65 to +150
°C
* Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or
conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions
is not implied.
1. IO absolute maximum rating must be observed.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Operating
Data Retention Only
Min
Typ
Max
Unit
1.65
1.2
3.3
3.3
3.6
3.6
V
–0.3
3.6
V
0
0
VCC
3.6
V
VCC
Supply Voltage
VI
Input Voltage
VO
Output Voltage
IOH
HIGH Level Output Current, VCC = 3.0V – 3.6V
–24
mA
IOL
LOW Level Output Current, VCC = 3.0V – 3.6V
24
mA
IOH
HIGH Level Output Current, VCC = 2.3V – 2.7V
–18
mA
IOL
LOW Level Output Current, VCC = 2.3V – 2.7V
18
mA
IOH
HIGH Level Output Current, VCC = 1.65 – 1.95V
–6
mA
IOL
LOW Level Output Current, VCC = 1.65 – 1.95V
6
mA
TA
Operating Free–Air Temperature
–40
+85
°C
∆t/∆V
Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V, VCC = 3.0V
0
10
ns/V
(Active State)
(3–State)
http://onsemi.com
3
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373
DC ELECTRICAL CHARACTERISTICS
TA = –40°C to +85°C
Symbol
VIH
VIL
VOH
VOL
II
II(HOLD)
II (OD)
2.
3.
4.
5.
Characteristic
Condition
Min
HIGH Level Input Voltage (Note 2.)
1.65V ≤ VCC < 2.3V
0.65 x VCC
2.3V ≤ VCC ≤ 2.7V
1.6
2.7V < VCC ≤ 3.6V
2.0
LOW Level Input Voltage (Note 2.)
HIGH Level Output Voltage
LOW Level Output Voltage
Input Leakage Current
Minimum Bushold Input Current
Minimum Bushold Over–Drive
C rrent Needed to Change State
Current
IOZ
3–State Output Current
IOFF
ICC
Power–Off Leakage Current
Quiescent Supply Current (Note 5.)
0.35 x VCC
2.3V ≤ VCC ≤ 2.7V
0.7
2.7V < VCC ≤ 3.6V
0.8
1.65V ≤ VCC ≤ 3.6V; IOH = –100µA
VCC – 0.2
VCC = 1.65V; IOH = –6mA
1.25
VCC = 2.3V; IOH = –6mA
2.0
VCC = 2.3V; IOH = –12mA
1.8
VCC = 2.3V; IOH = –18mA
1.7
VCC = 2.7V; IOH = –12mA
2.2
VCC = 3.0V; IOH = –18mA
2.4
VCC = 3.0V; IOH = –24mA
2.2
Unit
V
1.65V ≤ VCC < 2.3V
V
V
1.65V ≤ VCC ≤ 3.6V; IOL = 100µA
0.2
VCC = 1.65V; IOL = 6mA
0.3
VCC = 2.3V; IOL = 12mA
VCC = 2.3V; IOL = 18mA
0.4
VCC = 2.7V; IOL = 12mA
0.4
VCC = 3.0V; IOL = 18mA
0.4
VCC = 3.0V; IOL = 24mA
0.55
1.65V ≤ VCC ≤ 3.6V; 0V ≤ VI ≤ 3.6V
±5.0
V
0.6
VCC = 3.0V, VIN = 0.8V
75
VCC = 3.0V, VIN = 2.0V
–75
VCC = 2.3V, VIN = 0.7V
45
VCC = 2.3V, VIN = 1.6V
–45
VCC = 1.65V, VIN = 0.57V
25
VCC = 1.65V, VIN = 1.07V
–25
VCC = 3.6V, (Note 3.)
450
VCC = 3.6V, (Note 4.)
–450
VCC = 2.7V, (Note 3.)
300
VCC = 2.7V, (Note 4.)
–300
VCC = 1.95V, (Note 3.)
200
VCC = 1.95V, (Note 4.)
–200
µA
µA
µA
1.65V ≤ VCC ≤ 3.6V; 0V ≤ VO ≤ 3.6V;
VI = VIH or VIL
±10
µA
VCC = 0V; VI or VO = 3.6V
10
µA
1.65V ≤ VCC ≤ 3.6V; VI = GND or VCC
20
µA
1.65V ≤ VCC ≤ 3.6V; 3.6V ≤ VI, VO ≤ 3.6V
±20
µA
750
µA
∆ICC
Increase in ICC per Input
2.7V < VCC ≤ 3.6V; VIH = VCC – 0.6V
These values of VI are used to test DC electrical characteristics only.
An external driver must source at least the specified current to switch from LOW–to–HIGH
An external driver must source at least the specified current to switch from HIGH–to–LOW
Outputs disabled or 3–state only.
http://onsemi.com
4
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Max
NL74VCXH16373
AC CHARACTERISTICS (Note 6.; tR = tF = 2.0ns; CL = 30pF; RL = 500Ω)
Limits
TA = –40°C to +85°C
VCC = 3.0V to 3.6V
Symbol
Parameter
VCC = 2.3V to 2.7V
VCC = 1.65 to 1.95V
Waveform
Min
Max
Min
Max
Min
Max
Unit
tPLH
tPHL
Propagation Delay
Dn to On
1
0.8
0.8
3.0
3.0
1.0
1.0
3.4
3.4
1.5
1.5
6.8
6.8
ns
tPLH
tPHL
Propagation Delay
LE to On
1
0.8
0.8
3.0
3.0
1.0
1.0
3.9
3.9
1.5
1.5
7.8
7.8
ns
tPZH
tPZL
Output Enable Time to
High and Low Level
2
0.8
0.8
3.5
3.5
1.0
1.0
4.6
4.6
1.5
1.5
9.2
9.2
ns
tPHZ
tPLZ
Output Disable Time From
High and Low Level
2
0.8
0.8
3.5
3.5
1.0
1.0
3.8
3.8
1.5
1.5
6.8
6.8
ns
ts
Setup Time, High or Low Dn to LE
3
1.5
1.5
2.5
ns
th
Hold Time, High or Low Dn to LE
3
1.0
1.0
1.0
ns
tw
LE Pulse Width, High
3
1.5
1.5
4.0
ns
tOSHL
tOSLH
Output–to–Output Skew
(Note 7.)
0.5
0.5
0.5
0.5
0.75
0.75
ns
6. For CL = 50pF, add approximately 300ps to the AC maximum specification.
7. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter
guaranteed by design.
DYNAMIC SWITCHING CHARACTERISTICS
TA = +25°C
Symbol
VOLP
VOLV
VOHV
Characteristic
Condition
Typ
Unit
Dynamic LOW Peak Voltage
VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V
0.25
V
(Note 8.)
VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V
0.6
VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V
0.8
Dynamic LOW Valley Voltage
VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V
–0.25
(Note 8.)
VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V
–0.6
VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V
–0.8
Dynamic HIGH Valley Voltage
VCC = 1.8V, CL = 30pF, VIH = VCC, VIL = 0V
1.5
(Note 9.)
VCC = 2.5V, CL = 30pF, VIH = VCC, VIL = 0V
1.9
V
V
VCC = 3.3V, CL = 30pF, VIH = VCC, VIL = 0V
2.2
8. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW or LOW–to–HIGH. The remaining output is
measured in the LOW state.
9. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW or LOW–to–HIGH. The remaining output is
measured in the HIGH state.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
Condition
Typical
Unit
CIN
Input Capacitance
Note 10.
6
pF
COUT
Output Capacitance
Note 10.
7
pF
CPD
Power Dissipation Capacitance
Note 10., 10MHz
20
pF
10. VCC = 1.8, 2.5 or 3.3V; VI = 0V or VCC.
http://onsemi.com
5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373
VIH
Vm
Dn
Vm
0V
tPLH
tPHL
VOH
Vm
On
Vm
VOL
WAVEFORM 1 – PROPAGATION DELAYS
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 3. AC Waveforms
VIH
Dn
Vm
Vm
OEn
VIH
Vm
Vm
0V
tPZH
0V
ts
tPHZ
VIH
VOH
Vy
LEn
Vm
On
th
tw
Vm
Vm
≈ 0V
0V
tPLH, tPHL
tPZL
On
tPLZ
≈ VCC
VOH
On
Vm
Vm
VOL
Vx
VOL
WAVEFORM 3 – LE to On PROPAGATION DELAYS, LE MINIMUM
PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns except when noted
WAVEFORM 2 – OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 4. AC Waveforms
VCC
Symbol
3.3V ±0.3V
2.5V ±0.2V
1.8V ±0.15V
VIH
2.7V
VCC
VCC
Vm
1.5V
VCC/2
VCC/2
Vx
VOL + 0.3V
VOL + 0.15V
VOL + 0.15V
Vy
VOH – 0.3V
VOH – 0.15V
VCC
VOH – 0.15V
PULSE
GENERATOR
RL
DUT
CL
RT
TEST
RL
SWITCH
tPLH, tPHL
Open
tPZL, tPLZ
6V at VCC = 3.3 ±0.3V;
VCC× 2 at VCC = 2.5 ±0.2V; 1.8V ±0.15V
tPZH, tPHZ
GND
CL = 30pF or equivalent (Includes jig and probe capacitance)
RL = 500Ω or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
Figure 5. Test Circuit
http://onsemi.com
6
Powered by ICminer.com Electronic-Library Service CopyRight 2003
6V or VCC × 2
OPEN
GND
NL74VCXH16373
VIH
Vm
Dn
Vm
0V
tPLH
tPHL
VOH
Vm
On
Vm
VOL
WAVEFORM 4 – PROPAGATION DELAYS
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 6. AC Waveforms
VIH
Vm
OEn
VIH
Dn
Vm
Vm
Vm
0V
tPZH
0V
ts
tPHZ
VIH
VOH
Vy
LEn
Vm
On
th
tw
Vm
≈ 0V
Vm
0V
tPLH, tPHL
tPZL
On
tPLZ
VOH
≈ VCC
On
Vm
Vm
VOL
Vx
VOL
WAVEFORM 6 – LE to On PROPAGATION DELAYS, LE MINIMUM
PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns except when noted
WAVEFORM 5 – OUTPUT ENABLE AND DISABLE TIMES
tR = tF = 2.0ns, 10% to 90%; f = 1MHz; tW = 500ns
Figure 7. AC Waveforms
VCC
Symbol
3.3V ±0.3V
2.7V
VIH
2.7V
2.7V
Vm
1.5V
1.5V
Vx
VOL + 0.3V
VOL + 0.3V
Vy
VOH – 0.3V
VOH – 0.3V
http://onsemi.com
7
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373
AC CHARACTERISTICS (tR = tF = 2.0ns; CL = 50pF; RL = 500Ω)
Limits
TA = –40°C to +85°C
VCC = 3.0V to 3.6V
Symbol
Parameter
VCC = 2.7V
Waveform
Min
Max
Max
Unit
tPLH
tPHL
Propagation Delay
Dn to On
4
1.0
1.0
3.6
3.6
Min
4.3
4.3
ns
tPLH
tPHL
Propagation Delay
LE to On
4
1.0
1.0
3.9
3.9
4.6
4.6
ns
tPZH
tPZL
Output Enable Time to
High and Low Level
5
1.0
1.0
4.7
4.7
5.7
5.7
ns
tPHZ
tPLZ
Output Disable Time From
High and Low Level
5
1.0
1.0
4.1
4.1
4.5
4.5
ns
tOSHL
tOSLH
Output–to–Output Skew
(Note 11.)
0.5
0.5
0.5
0.5
ns
11. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter
guaranteed by design.
VCC
PULSE
GENERATOR
RL
DUT
RT
CL
RL
SWITCH
TEST
tPLH, tPHL
Open
tPZL, tPLZ
6V at VCC = 3.3 ±0.3V;
VCC× 2 at VCC = 2.5 ±0.2V; 1.8V ±0.15V
tPZH, tPHZ
GND
CL = 50pF or equivalent (Includes jig and probe capacitance)
RL = 500Ω or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
Figure 8. Test Circuit
http://onsemi.com
8
Powered by ICminer.com Electronic-Library Service CopyRight 2003
6V or VCC × 2
OPEN
GND
NL74VCXH16373
PACKAGE DIMENSIONS
TSSOP
DT SUFFIX
CASE 1201–01
ISSUE A
48X
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
K
K1
K REF
0.12 (0.005)
M
T U
S
V
S
T U
S
J J1
48
25
SECTION N–N
M
0.254 (0.010)
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
5. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
6. DIMENSIONS A AND B ARE TO BE
DETERMINED AT DATUM PLANE –W–.
B
–U–
L
N
1
24
A
–V–
PIN 1
IDENT.
N
F
DETAIL E
D
C
0.25 (0.010)
–W–
0.076 (0.003)
–T– SEATING
DETAIL E
PLANE
MILLIMETERS
MIN
MAX
12.40
12.60
6.00
6.20
–––
1.10
0.05
0.15
0.50
0.75
0.50 BSC
0.37
–––
0.09
0.20
0.09
0.16
0.17
0.27
0.17
0.23
7.95
8.25
0_
8_
H
G
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
É
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
É
ÉÉ
ÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
É
ÉÉ
ÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
ÉÉÉÉ
ÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
É
ÉÉ
ÉÉÉÉ
ÉÉÉÉÉÉÉ
F
K
L
M
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
G
48 Leads
Package Footprint
http://onsemi.com
9
Powered by ICminer.com Electronic-Library Service CopyRight 2003
INCHES
MIN
MAX
0.488
0.496
0.236
0.244
–––
0.043
0.002
0.006
0.020
0.030
0.0197 BSC
0.015
–––
0.004
0.008
0.004
0.006
0.007
0.011
0.007
0.009
0.313
0.325
0_
8_
NL74VCXH16373
10 PITCHES
CUMULATIVE
TOLERANCE ON
TAPE
±0.2 mm
(±0.008”)
P0
K
P2
D
t
TOP
COVER
TAPE
E
A0
+
K0
SEE
NOTE 2
B1
SEE NOTE 2
F
+
B0
W
+
D1
FOR COMPONENTS
2.0 mm × 1.2 mm
AND LARGER
P
EMBOSSMENT
FOR MACHINE REFERENCE
ONLY
INCLUDING DRAFT AND RADII
CONCENTRIC AROUND B0
CENTER LINES
OF CAVITY
USER DIRECTION OF FEED
*TOP COVER
TAPE THICKNESS (t1)
0.10 mm
(0.004”) MAX.
R MIN.
TAPE AND COMPONENTS
SHALL PASS AROUND RADIUS “R”
WITHOUT DAMAGE
EMBOSSED
CARRIER
BENDING RADIUS
10°
100 mm
(3.937”)
MAXIMUM COMPONENT ROTATION
EMBOSSMENT
1 mm MAX
TYPICAL
COMPONENT CAVITY
CENTER LINE
TAPE
1 mm
(0.039”) MAX
TYPICAL
COMPONENT
CENTER LINE
250 mm
(9.843”)
CAMBER (TOP VIEW)
ALLOWABLE CAMBER TO BE 1 mm/100 mm NONACCUMULATIVE OVER 250 mm
Figure 9. Carrier Tape Specifications
EMBOSSED CARRIER DIMENSIONS (See Notes 1 and 2)
Tape
Size
B1
Max
24mm
20.1mm
(0.791”)
D
D1
E
F
K
P
P0
P2
R
T
W
1.5 + 0.1mm
–0.0
(0.059
+0.004” –0.0)
1.5mm
Min
(0.060”)
1.75
±0.1 mm
(0.069
±0.004”)
11.5
±0.10 mm
(0.453
±0.004”)
11.9 mm
Max
(0.468”)
16.0
±0.1 mm
(0.63
±0.004”)
4.0
±0.1 mm
(0.157
±0.004”)
2.0
±0.1 mm
(0.079
±0.004”)
30 mm
(1.18”)
0.6 mm
(0.024”)
24.3 mm
(0.957”)
1. Metric Dimensions Govern–English are in parentheses for reference only.
2. A0, B0, and K0 are determined by component size. The clearance between the components and the cavity must be within 0.05 mm min to
0.50 mm max. The component cannot rotate more than 10° within the determined cavity
http://onsemi.com
10
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373
t MAX
13.0 mm ±0.2 mm
(0.512” ±0.008”)
1.5 mm MIN
(0.06”)
A
20.2 mm MIN
(0.795”)
50 mm MIN
(1.969”)
FULL RADIUS
G
Figure 10. Reel Dimensions
REEL DIMENSIONS
Tape Size
A Max
G
t Max
24 mm
360 mm
(14.173”)
24.4 mm + 2.0 mm, –0.0
(0.961” + 0.078”, –0.00)
30.4 mm
(1.197”)
DIRECTION OF FEED
BARCODE LABEL
POCKET
Figure 11. Reel Winding Direction
http://onsemi.com
11
Powered by ICminer.com Electronic-Library Service CopyRight 2003
HOLE
NL74VCXH16373
CAVITY
TAPE
TOP TAPE
TAPE TRAILER
(Connected to Reel Hub)
NO COMPONENTS
160 mm MIN
COMPONENTS
TAPE LEADER
NO COMPONENTS
400 mm MIN
DIRECTION OF FEED
Figure 12. Tape Ends for Finished Goods
User Direction of Feed
Figure 13. Reel Configuration
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (M–F 1:00pm to 5:00pm Munich Time)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (M–F 1:00pm to 5:00pm Toulouse Time)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (M–F 12:00pm to 5:00pm UK Time)
Email: [email protected]
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, England, Ireland
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–8549
Phone: 81–3–5740–2745
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
http://onsemi.com
12
Powered by ICminer.com Electronic-Library Service CopyRight 2003
NL74VCXH16373/D