QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER QS52805T/AT FEATURES: DESCRIPTION − − The QS52805T clock buffer/driver circuits can be used for clock buffering schemes where low skew is a key parameter. This device offers two banks of five non-inverting outputs. This device provides low propagation delay buffering with on-chip skew of 0.7ns for same-transition, same-bank signals. − − − − − − 10 output, low skew signal buffer Guaranteed low skew: • 0.7ns output skew (same bank) • 0.9ns output skew (different bank) • 1ns part-to-part skew 25Ω on-chip resistors available for low noise Input hysteresis for better noise margin Monitor output Undershoot clamp diodes on all inputs Std. and A speed grades Available in QSOP and SOIC packages The QS52805T has on-chip series termination resistors for lower noise clock signals. The QS52805T series resistor version is recommended for driving unterminated lines with capacitive loading and other noise sensitive clock distribution circuits. These clock buffer products are designed for use in high-performance workstations and in embedded and personal computing systems. Several devices can be used in parallel or scattered throughout a system for guaranteed low skew, system-wide clock distribution networks. The QS52805T is characterized for operation at -40°C to +85°C. FUNCTIONAL BLOCK DIAGRAM OE A 5 OA 5 IN A OA 1 MON 5 OB 5 IN B OB 1 OE B NOTE: This device has 25Ω series termination resistors on each clock output including monitor. INDUSTRIAL TEMPERATURE RANGE AUGUST 2000 1 c 1999 Integrated Device Technology, Inc. DSC-5480/- QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION Symbol VTERM(2) (1) Description Supply Voltage to Ground Max. – 0.5 to +7 Unit V V CC A 1 20 V CC B DC Output Voltage VOUT – 0.5 to +7 V OA1 2 19 OB1 VTERM(3) DC Input Voltage VIN – 0.5 to +7 V OA2 3 18 OB2 VAC AC Input Voltage (pulse width ≤20ns) -3 V OA3 4 17 OB3 IOUT DC Input Diode Current VIN < 0 -20 mA DC Output Current Max. Sink Current/Pin 120 mA 16 G ND B 15 OB4 7 14 OB5 G N DQ 8 13 MON O EA 9 12 O EB IN A 10 11 IN B G ND A 5 OA4 6 OA5 SO20-2 SO20-8 TSTG Storage Temperature – 65 to +150 °C TJ Junction Temperature 150 °C NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Vcc Terminals. 3. All terminals except Vcc. QSOP/ SOIC TOP VIEW CAPACITANCE (TA = +25OC, f = 1.0MHz, VIN = 0V) Pins CIN Typ. 4 Max. (1) 6 Unit pF COUT 7 9 pF NOTE: 1. This parameter is guaranteed but not production tested. PIN DESCRIPTION Pin Names OEA, OEB 2 I/O I Description Output Enable Inputs INA, INB I Clock Inputs OAn, OBn O Clock Outputs MON O Unbuffered Monitor Output QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40°C to +85°C, VCC = 5.0V ± 10% Symbol VIH Parameter Input HIGH Voltage Test Conditions Guaranteed Logic HIGH for All Inputs Min. 2 Typ.(1) — Max. — Unit V VIL Input LOW Voltage Guaranteed Logic LOW for All Inputs — — 0.8 V Vcc = Min., IIN = -18mA — –0.7 –1.2 V 2.4 — — V (3) VIC Clamp Diode Voltage VOH Output HIGH Voltage Vcc = Min., IOH = -12mA VOL Output LOW Voltage Vcc = Min., IOL = 12mA — — 0.5 V IIN Input Leakage Current Vcc = Max., VIN = Vcc or GND — — ±1 µA IOFF Input/Output Power Off Leakage Vcc = 0V, VIN or VOUT = Vcc or GND — — ±1 µA IOZ Output Leakage Current Vcc = Max., VOUT = Vcc or GND IOS Short Circuit Current ∆VT ROUT — — ±1 µA Vcc = Max., VOUT = GND –60 — –250 mA Input Hysteresis VTLH - VTHL for All Inputs — 0.2 — V Output Resistance Vcc = Min., IOL = 12mA — 28 — Ω (2,3) NOTES: 1. Typical values are at VCC = 5.0V, TA = 25°C. 2. Not more than one output should be used to test this high power condition. Duration is less than one second. 3. Guaranteed by design but not tested. POWER SUPPLY CHARACTERISTICS Parameter Quiescent Power Supply Current Test Conditions (1) VCC = Max., VIN = GND or Vcc ∆ICC Supply Current per Input HIGH ICCD Dynamic Power Supply Current per Output (2) IC Total Power Supply Current Examples (2,4) Symbol ICC Typ. (3) 0.005 Max. 0.5 Unit mA VCC = Max., VIN = 3.4V, fI = 0MHz 1 2.5 mA VCC = Max., VIN = GND or Vcc Outputs Enabled, 50% duty cycle VCC = Max., OEA = OEB = GND 50% duty cycle, fI = 10MHz Five outputs toggling Unused inputs = GND or Vcc VCC = Max., OEA = OEB = GND 50% duty cycle, fI = 2.5MHz All outputs toggling 0.08 0.18 mA/MHz VIN = GND or Vcc 6.6 9.5 mA VIN = GND or 3.4V 7.2 10.8 VIN = GND or Vcc 4.3 5.5 VIN = GND or 3.4V 5.6 8 NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Guaranteed by design but not tested. CL = 0pF. 3. Typical values are for reference only. Conditions are VCC = 5.0V, TA = 25°C. 4. IC = ICC + (∆ICC)(DH)(NT) + ICCD (fO)(NO) where: DH = Input Duty Cycle NT = Number of TTL HIGH inputs at DH (one or two) fO = Output Frequency NO = Number of outputs at fO 3 QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE SKEW CHARACTERISTICS OVER OPERATING RANGE TA = -40°C to +85°C, VCC = 5.0V ± 10% CLOAD = 50pF (no resistor) QS52805T Parameter (1) Symbol QS52805AT Min. Max. Min. Max. Unit tSK(01) Skew between two outputs, same transition, same bank — 0.7 — 0.7 ns tSK(02) Skew between two outputs, same transition, different banks — 0.9 — 0.9 ns tSK(P) Pulse Skew; opposite transition skew, same output (tPHL - tPLH) — 1 — 1 ns tSK(T) Part-to-part skew (2) — 1.5 — 1 ns NOTES: 1. Skew parameters are guaranteed across temperature range, but not tested. Skew parameters apply to propagation delays only. 2. tSK(T) only applies to devices of the same transition, part type, temperature, power supply voltage, loading, package, and speed grade. SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40°C to +85°C, VCC = 5.0V ± 10% CLOAD = 50pF (no resistor) QS52805T Symbol tPLH tPHL tPZL tPZH tPLZ tPHZ Parameter (1) Propagation Delay (2) tR Output Rise Time, 0.8V to 2V (3) tF Output Enable Time Output Disable Time Output Fall Time, 2V to 0.8V (3) QS52805AT Min. Max. Min. Max. Unit 1.5 6.5 1.5 5.8 ns 1.5 8 1.5 8 ns 1.5 7 1.5 7 ns — 1.5 — 1.5 ns — 1.5 — 1.5 ns NOTES: 1. Minimums guaranteed but not production tested. 2. The propagation delay other range indicated by Min. and Max. specifications results from process and environmental variables. These propagation delays do not imply limit skew. 3. This parameter is guaranteed but not tested. 4 QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS Parameter Tested Switch Position tPLZ, tPZL Closed All Others Open 500Ω V CC 6.0 V V IN V OUT Pulse Generator DUT 50 Ω 50pF 500Ω Pulse generator for all pulses: f ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns PROPAGATION DELAY PULSE SKEW — tSK(P) 3V 3V 1.5V INPUT 0V tPLH 1.5V INPUT tPHL 0V VOH 2.0V 1.5V 0.8V VOL OUTPUT tR tPHL tPLH VOH OUTPUT 1.5V VOL tF tSK(p) = t PHL - tPLH OUTPUT SKEW (SAME BANK) — tSK(O1) OUPUT SKEW (DIFFERENT BANKS) — tSK(O2) 3V 3V 1.5V INPUT 1.5V INPUT 0V 0V tPHL1 tPLH1 tPHLA tPLHA VOH OUTPUT 1 VOH OUTPUT A 1.5V 1.5V VOL tSK(01) tSK(01) VOL OUTPUT 2 tSK(02) tSK(02) VOH OUTPUT B 1.5V 1.5V VOL VOL tPLH2 tPLHB tPHL2 tSK(01) = tPLH2 - tPLH1 or tPHL2 - tPHL1 tPHLB tSK(02) = tPLHB - tPLHA or tPHLB - tPHLA PART-TO-PART SKEW — tSK(T) ENABLE AND DISABLE TIMES ENABLE DISABLE 3V 3V CONTROL INPUT 1.5V 0V tPLH1 tPLZ tPHL1 VOH 3V SWITCH CLOSED PART 1 OUTPUT 1.5V VOL tPHZ tSK(t) 0.3V VOH SWITCH OPEN 1.5V 0.3V V OL tPZH OUTPUT NORMALLY HIGH 1.5V INPUT 0V tPZL OUTPUT NORMALLY LOW VOH 1.5V tSK(t) PART 2 OUTPUT VOH 1.5V VOL 0V tPLH2 tPHL2 tSK(t) = t PLH2 - tPLH1 or tPHL2 - tPHL1 5 QS52805T/AT GUARANTEED LOW SKEW CMOS CLOCK DRIVER/BUFFER INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION QS XXXX XX Device Type Package Q SO Quarter Size Small Outline Package (SO20-8) Small Outline IC (SO20-2) Guaranteed Low Skew CMOS Clock Driver/Buffer 52805T 52805AT CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com* *To search for sales office near you, please click the sales button found on our home page or dial the 800# above and press 2. The IDT logo, QuickSwitch, and SynchroSwitch are registered trademarks of Integrated Device Technology, Inc. 6