ETC UC3770BQ

UC3770A
UC3770B
High Performance Stepper Motor Drive Circuit
FEATURES
DESCRIPTION
•
Full-Step, Half-Step and Micro-Step
Capability.
•
Bipolar Output Current up to 2A.
•
Wide Range of Motor Supply Voltage:
10–50V
•
Low Saturation Voltage
The UC3770A and UC3770B are high-performance full bridge drivers that offer higher current and lower saturation voltage than the
UC3717 and the UC3770. Included in these devices are LS-TTL
compatible logic inputs, current sense, monostable, thermal shutdown, and a power H-bridge output stage. Two UC3770As or
UC3770Bs and a few external components form a complete microprocessor-controllable stepper motor power system.
•
Wide Range of Current Control: 5mA–2A.
•
Current Levels Selected in Steps or Varied
Continuously.
•
Thermal Protection and Soft Intervention.
Unlike the UC3717, the UC3770A and the UC3770B require external high-side clamp diodes. The UC3770A and UC3770B are
identical in all regards except for the current sense thresholds.
Thresholds for the UC3770A are identical to those of the older
UC3717 permitting drop-in replacement in applications where
high-side diodes are not required. Thresholds for the UC3770B are
tailored for half stepping applications where 50%, 71%, and 100%
current levels are desirable.
The UC3770A and UC3770B are specified for operation from 0°C
to 70°C ambient.
BLOCK DIAGRAM
UDG-92039-1
SLUS403A - FEBRUARY 2000
UC3770A
UC3770B
ABSOLUTE MAXIMUM RATINGS
Logic Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Output Supply Voltage, VMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50V
Logic Input Voltage (Pins 7, 8, 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
Analog Input Voltage (Pin 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC
Reference Input Voltage (Pin 11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Logic Input Current (Pins 7, 8, 9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10mA
Analog Input Current (Pins 10, 11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –10mA
Output Current (Pins 1, 15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 2A
Junction Temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Note 1: All voltages are with respect to Gnd (DIL Pins 4, 5, 12, 13); all currents
are positive into, negative out of the specified terminal.
Note 2: Consult Unitrode Integrated Circuits databook for thermal limitations and
considerations of packages.
CONNECTION DIAGRAMS
DIL-16 (Top View)
J Or N Package
PACKAGE PIN FUNCTION
PLCC-28 (Top View)
Q Package
FUNCTION
PIN
Gnd
VM
N/C
AOUT
N/C
Emitters
Gnd
BOUT
Timing
VM
Gnd
VCC
I1
Phase
I0
N/C
Current
VR
N/C
Gnd
1-3
4
5
6
7
8
9
10
11
12
13-17
18
19
20
21
22
23
24
25-27
28
ELECTRICAL CHARACTERISTICS: (All tests apply with VM = 36V, VCC = 5V, VR = 5V, No Load, and 0°C<TA<70°C, unless
otherwise stated, TA = TJ.)
UC3770A
PARAMETER
TEST CONDITIONS
Supply Voltage VM (Pins 3, 14)
TYP
10
Logic Supply Voltage VCC (Pin 6)
Logic Supply Current ICC (Pin 6)
MIN
4.75
UC3770B
MAX
MIN
45
10
4.75
TYP
MAX UNITS
45
V
5
5.3
5
5.3
V
IO = I1 = H, IM = 0
15
25
15
25
mA
IO = I1 = L, IM = 0
18
28
18
28
mA
IO = I1 = H, IM = 1.3A
33
40
33
40
mA
Thermal Shutdown Temperature
+170
Logic Threshold (Pins 7, 8, 9)
0.8
°C
+170
2.0
0.8
2.0
V
Input Current Low (Pin 8)
VI = 0.4V
-100
-100
µA
Input Current Low (Pins 7, 9)
VI = 0.4V
-400
-400
µA
Input Current High (Pins 7, 8, 9)
VI = 2.4V
10
µA
Comparator Threshold (Pin 10)
VR = 5V, I0 = L, I1 = L
400
415
430
400
415
430
mV
VR = 5V, I0 = H, I1 = L
240
255
265
290
300
315
mV
VR = 5V, I0 = L, I1 = H
70
80
90
195
210
225
mV
±20
µA
35
ms
10
±20
Comparator Input Current (Pin 10)
Off Time
RT = 56k, CT = 820pF
25
2
30
35
25
30
UC3770A
UC3770B
ELECTRICAL CHARACTERISTICS (cont.): (All tests apply with VM = 36V, VCC = 5V, VR = 5V, No Load, and 0°C<TA<70°C,
unless otherwise stated, TA = TJ.)
UC3770A
PARAMETER
TEST CONDITIONS
MIN
TYP
UC3770B
MAX
Turn Off Delay
Sink Driver Saturation Voltage
Source Driver Saturation Voltage
Output Leakage Current
MIN
2
2
ms
0.8
0.8
V
IM = 1.3A
1.3
1.3
V
IM = 1.0A
1.3
1.3
V
IM = 1.3A
1.6
1.6
V
VM = 45V
100
100
µA
TA = +25°C
1.8
5.0
1.6
4.5
ICC – mA
VCE SAT HIGH – V
MAX UNITS
IM = 1.0A
TA = +25°C
1.4
1.2
4.0
3.5
1.0
3.0
0.8
2.5
0.6
0.2
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
OUTPUT CURRENT – A
OUTPUT CURRENT – A
Figure 1. Typical source saturation voltages vs. load
current
Figure 3. Typical supply current vs. load current.
POWER DISSIPATION (W)
TA = +25°C
VCE SAT LOW – V
TYP
1.4
1.2
1.0
0.8
0.6
0.4
0.2
5
4
3
2
1
0
0
0.5
1
1.5
OUTPUT CURRENT (A)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
OUTPUT CURRENT – A
Figure 2. Typical sink saturation voltages vs. load
current
Figure 4. Typical power dissipation vs. output
current.
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. 603-424-2410 • FAX 603-424-3460
3
2
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  2000, Texas Instruments Incorporated