REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Make changes to 1.2.2, Table I, and figure 1. 94-01-06 M. A. FRYE B Add device type 03. Add case outline 2. Changes to ICC, VRLINE2, VRLOAD2, IIB, VOL, VOH, AVOL, CMRR, and VSATL in table I. Update boilerplate. -rrp 01-02-22 R. MONNIN REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. OFFICER STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 http://www.dscc.dla.mil CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RESONANT-MODE POWER SUPPLY CONTROLLERS, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-03-30 REVISION LEVEL B SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 5962-92031 11 5962-E095-01 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92031 Federal stock class designator \ RHA designator (see 1.2.1) 01 M E X Device type (see 1.2.2) Device class designator (see 1.2.3) Case outline (see 1.2.4) Lead finish (see 1.2.5) / \/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 02 03 Circuit function UC1864 UC1865 UC1863 Resonant-mode power supply controller Resonant-mode power supply controller Resonant-mode power supply controller 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, nonJAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter E 2 Descriptive designator GDIP1-T16 or CDIP2-T16 CQCC1-N20 Terminals Package style 16 20 Dual-in-line Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 2 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage (VCC) .................................................................................... Output current (OUTPUT A and OUTPUT B): Source and sink ....................................................................................... Pulse ........................................................................................................ Power ground voltage .................................................................................. Inputs (+INPUT, -INPUT, ZERO, FAULT) .................................................... Error amp output current ............................................................................. Power dissipation (PD) at 70C ................................................................. Junction temperature (TJ) ............................................................................ Lead temperature (soldering, 10 seconds) .................................................. Storage temperature range ......................................................................... Thermal resistance, junction-to-case (JC) .................................................. Thermal resistance, junction-to-ambient (JA): Case E ..................................................................................................... Case 2 ...................................................................................................... 22 V dc 0.5 A 1.5 A 0.2 V -0.4 V to 7 V 2 mA 1 W 3/ +150C +300C -65C to +150C See MIL-STD-1835 85C/W 80C/W 1.4 Recommended operating conditions. Supply voltage (VCC) .................................................................................... 12 V dc Ambient operating temperature (TA) ............................................................ -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ 2/ 3/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. All voltages are with respect to signal ground and all currents are positive into the specified terminal. Derate at 12.5 mW at TA > 70C. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 3 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 58 (see MIL-PRF-38535, appendix A). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Min Unit ICC start ICC VCC = VCC(ON) – 0.3 V 1,2,3 All Max 300 A ICC run ICC VID = 100 mV 1,2,3 All 32 mA VOUT 12 V VCC 20 V, 1,2,3 All 4.8 5.2 V 1,2,3 All -150 -15 mA 1 All 4.95 5.05 V 4.85 5.15 5 V Generator section Output voltage -10 mA IOUT 0 mA Short circuit current IOS VOUT = 0 V VREF IOUT = 0 mA, TA = +25C Soft reference section Reference voltage 12 V VCC 20 V, 1,2,3 -200 A IOUT 200 A Line regulation VRLINE2 VCC = 12 V and 20 V 1,2,3 All -20 20 mV Load regulation VRLOAD2 IOUT = 200 A 1,2,3 All -30 30 mV Soft start current ISS V=2V 1,2,3 All -650 -350 A Restart delay current IRD V=2V 1,2,3 All 10 35 A 10 mV Error amplifier section (VID = V+INPUT – V-INPUT) Input offset voltage VIO VCM = 5 V, VOUT = 2 V, IOUT = 0 mA 1,2,3 All -10 Input bias current IIB VCM = 0 V 1,2,3 All -2 Output voltage, low VOL VID = -100 mV, 1,2,3 All Output voltage, high VOH VID = 100 mV, 1,2,3 All 3.9 V Voltage gain AVOL VCM = 5 V, IOUT = 0 mA, VOUT = 0.5 V and 3.7 V 1,2,3 All 70 dB Power supply rejection ratio PSRR VCM = 5 V, VOUT = 2 V, VCC = 12 V and 20 V 1,2,3 All 70 dB A 0.25 V IOUT = 200 A IOUT = -200 A See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 5 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Min Unit Max Error amplifier section – Continued. (VID = V+INPUT – V-INPUT) Common mode rejection ratio CMRR VOUT = 2 V, VCM = 0 V and 6 V 4,5,6 All 65 dB Unity gain bandwidth UGBW 3/ 4,5,6 All 0.5 MHz 4 All 450 550 425 575 45 55 42 58 Voltage controlled oscillator (VCO) section Maximum frequency fMAX VID (error amp) = 100 mV 5,6 Minimum frequency fMIN VID (error amp) = -100 mV 4 All 5,6 kHz kHz One shot section Zero comparator threshold VTHZ 1,2,3 All 0.45 0.55 V Maximum pulse width, OUTPUT A tMAX VZERO = 1 V 9,10,11 All 850 1150 ns Ratio of maximum to minimum pulse width tMIN/tMAX VZERO = 0 V 9,10,11 01, 03 2.5 5.5 % 9,11 02 4 7 Propagation delay tPD 3/ 3.8 7 Output low saturation (outputs A and B) VSATL IOUT = 20 mA Output high saturation (outputs A and B) VSATH IOUT = -200 mA, down from VCC 1,2,3 All 2.5 V Under-voltage lockout (UVLO), low saturation (outputs A and B) VSL A,B IOUT = 20 mA 1,2,3 All 1.5 V Rise and fall time tR, tF CL = 1 nF 9,10,11 All 45 ns 10 9,10,11 All 200 ns 1,2,3 All 0.5 V Output stage section IOUT = 200 mA 2.2 3/ See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 6 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Min Unit Max Fault comparator section Fault comparator threshold voltage VTHF Delay to output tDO 3/ 4/ 1,2,3 All 2.85 3.15 V 1,2,3 All 200 ns 1,2,3 01, 03 7 9 V 02 15 18 01, 03 6 8 9.5 11.5 Under-voltage lockout (UVLO) section VCC start threshold VCC stop threshold VSTT VSPT 1,2,3 02 V 1/ Unless otherwise specified, VCC = 12 V, voltage controlled oscillator capacitance CVCO = 1 nF, range resistance = 7.15 k, RMIN resistance = 86.6 k, capacitance = 200 pF, resistance = 4.02 k, and soft ref capacitance = 0.1 F. 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ If not tested, shall be guaranteed to the limits specified under table I herein. 4/ VIN = 0 V to 4 V, tR(VIN) 10 ns, and tPD = t(VOUT = 6 V) – t(VIN = 3 V). 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 7 Device types Case outlines Terminal number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 01, 02 and 03 01 and 03 E 2 Terminal symbol 5V SOFT REF +INPUT 5V -INPUT +INPUT E/A OUT -INPUT SIG GND E/A OUT RANGE SIG GND RMIN RANGE CVCO RMIN RC CVCO ZERO RC OUTPUT A ZERO PWR GND NC VCC NC OUTPUT B OUTPUT A FAULT PWR GND SOFT REF PWR GND ---VCC ---OUTPUT B ---NC ---FAULT NC = No connect FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 8 TABLE II. Electrical test requirements. Test requirements Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Group A test requirements (see 4.4) Group C end-point electrical parameters (see 4.4) Group D end-point electrical parameters (see 4.4) Group E end-point electrical parameters (see 4.4) Subgroups (in accordance with MIL-STD-883, method 5005, table I) Device class M 1 Subgroups (in accordance with MIL-PRF-38535, table III) Device class Q Device class V 1 1 1,2,3 1,2,3,4,5, 1/ 6,9,10,11 1,2,3,4,5,6, 9,10,11 1,2,3 1,2,3,4,5, 1/ 6,9,10,11 1,2,3,4,5,6, 9,10,11 1,2,3 1,2,3 1,2,3 1,2,3 --- --- --- 1,2,3,4,5, 1/ 6,9,10,11 1,2,3,4,5,6,9,10,11 1/ PDA applies to subgroup 1. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in MIL-PRF-38535, appendix B. 4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein. Quality conformance inspection for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4). 4.4.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 in table I, method 5005 of MIL-STD-883 shall be omitted. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 9 4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein. 4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883: a. Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. b. TA = +125C, minimum. c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. 4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein. 4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured (see 3.5 herein). a. End-point electrical parameters shall be as specified in table II herein. b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C, after exposure, to the subgroups specified in table II herein. c. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor prepared specification or drawing. 6.1.2 Substitutability. Device class Q devices will replace device class M devices. 6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus when a system application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43216-5000, or telephone (614) 692-0674. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 10 6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in MIL-PRF-38535 and MIL-HDBK-1331. 6.6 Sources of supply. 6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to this drawing. 6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-92031 A REVISION LEVEL B SHEET 11 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 01-02-22 Approved sources of supply for SMD 5962-92031 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. Standard microcircuit drawing PIN 1/ 5962-9203101MEA 5962-9203101M2A 5962-9203102MEA 5962-9203103QEA 5962-9203103Q2A 5962-9203103VEA 5962-9203103V2A Vendor CAGE number 01295 01295 3/ 01295 01295 01295 01295 Vendor similar PIN 2/ UC1864J/883 UC1864L/883 UC1865J/883 UC1863J/883 UC1863L/883 UC1863JQMLV UC1863LQMLV 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 01295 Vendor name and address Texas Instruments, Incorporated 13500 North Central Express way P.O. Box 655303 Dallas, TX 75265 Point of contact: 6412 Highway 75 South Sherman, TX 75090-0084 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.