GF9331 HDTV/SDTV Motion Co-processor DATA SHEET DEVICE OVERVIEW • support for 10/8-bit HDTV/SDTV input video signals The GF9331 is a high performance motion co-processor that is used in conjunction with Gennum's GF9330 HDTV/SDTV 10-bit De-interlacer. Together, the GF9331 and the GF9330 provide 10-bit broadcast quality de-interlacing for standard and high-definition video signals up to 1080p60. • seamless interface to Gennum's GF9330 high performance de-interlacer through a filter control bus • multi-directional edge detection and control • support for multiplexed and non-mutiplexed Y/C video • 3-field vertical motion detection and control • fully configurable to support custom video modes • ability to extract HVF information from embedded TRS • seamless interface to popular ADCs and NTSC/PAL decoders • user configuration through a dedicated host interface, supporting parallel and serial interfaces • 5V tolerant inputs Filter selection controls are sent to the GF9330 on a pixelby-pixel basis. The GF9331 integrates all the necessary line delays for the motion and edge detectors. The GF9331 also provides seamless interfaces to off-chip SDRAMs that form the required field delays. • 3.3V supply for device I/O and 2.5V for core logic APPLICATIONS • HDTV Up/Down Converters • Production Equipment • Video Walls • Projection Systems • Plasma Displays • LCD TVs • Home Theatre Systems • HD DVD Players Although the GF9330 can fully function as a standalone de-interlacer, the GF9331 provides added features in the form of a filter selection control bus that enables multi-directional edge and adaptive 3-field vertical motion detection. Edge detection and interpolation removes the edge artifacts that tend to occur while de-interlacing on shallow horizontal edges while vertical motion detection reduces motion artifacts. ORDERING INFORMATION PART NUMBER PACKAGE TEMP. RANGE GF9331-CBP 328 PIN BGA 0°C to 70°C Edge Detection Y/C Encoder Pre-filter Control bus to GF9330 Vertical Motion Detection Delay Y/C Delayed Video to GF9330 External Memory Interface BLOCK DIAGRAM Revision Date: October 2002 Document No. 18303 - 3 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected] www.gennum.com GF9331 FEATURES 1 2 3 4 5 6 7 8 9 RESET NC S2_DAT0 S2_DAT2 S2_DAT4 S2_DAT7 S2_DAT10 S2_DAT13 S2_CLK S2_ADDR2 10 11 12 13 14 15 16 17 18 19 20 S2_ADDR7 S2_ADDR10 S2_ADDR13 S2_CS S2_WE NC NC NC NC Y_OUT9 Y_IN9 NC S2_DAT1 S2_DAT3 S2_DAT5 S2_DAT8 S2_DAT11 S2_DAT14 S2_ADDR0 S2_ADDR3 S2_ADDR6 S2_ADDR9 S2_ADDR12 S2_CAS S2_RAS NC NC NC NC Y_OUT8 Y_IN8 Y_IN7 Y_IN6 NC S2_DAT6 S2_DAT9 S2_DAT12 S2_DAT15 S2_ADDR1 S2_ADDR4 S2_ADDR5 S2_ADDR8 S2_ADDR11 NC NC NC NC NC Y_OUT6 Y_OUT7 Y_IN5 Y_IN4 Y_IN3 NC NC NC NC NC NC NC NC NC NC NC NC NC NC Y_OUT3 Y_OUT4 Y_OUT5 Y_IN2 Y_IN1 Y_IN0 HOST_EN GND VDD_INT VDD_IO NC GND VDD_IO GND VDD_INT NC GND VDD_IO GND NC Y_OUT0 Y_OUT1 Y_OUT2 VCLK_IN NC MODE NC VDD_CLKD VDD_INT VDD_IO GND VDD_IO VDD_INT NC NC NC NC SER_MD STD4 STD3 STD2 VSS_CLKD VDD_INT GND VDD_INT NC NC NC NC MEMCLK_IN STD1 STD0 XVOCLK_SL GND GND GND NC NC NC C_OUT9 XVOCLK_IN NC C_IN9 C_IN8 VDD_IO TGND TGND TGND TGND VDD_IO NC C_OUT6 C_OUT7 C_OUT8 C_IN7 C_IN6 C_IN5 C_IN4 GND TGND TGND TGND TGND GND NC C_OUT3 C_OUT4 C_OUT5 C_IN0 C_IN1 C_IN2 C_IN3 VDD_INT TGND TGND TGND TGND GND NC C_OUT2 C_OUT1 C_OUT0 ED_MODE VM_MODE NC NC GND TGND TGND TGND TGND VDD_IO NC NC FIL_SEL3 FIL_SEL2 FVH_EN F_IN V_IN H_IN VDD_IO GND NC NC FIL_SEL1 FIL_SEL0 A_D CS R_W NC GND GND GND VDD_INT NC NC NC H_OUT DAT_IO4 DAT_IO5 DAT_IO6 DAT_IO7 NC VDD_INT VDD_IO VDD_IO VDD_INT NC NC NC V_OUT DAT_IO0 DAT_IO1 DAT_IO2 DAT_IO3 GND VDD_INT VDD_IO NC GND VDD_IO GND VDD_INT NC GND VDD_IO GND NC NC NC F_OUT TCLK TMS TDI GND NC NC NC NC NC NC NC NC NC NC NC NC NC GND GND GND GND GND NC NC NC S1_ADDR11 S1_ADDR8 S1_ADDR5 S1_ADDR2 S1_ADDR0 S1_DAT15 S1_DAT12 S1_DAT9 S1_DAT6 S1_DAT3 NC NC NC NC NC TDO NC NC S1_RAS S1_CAS S1_ADDR12 S1_ADDR9 S1_ADDR6 S1_ADDR3 S1_ADDR1 S1_DAT14 S1_DAT11 S1_DAT8 S1_DAT5 S1_DAT2 NC NC NC NC NC NC NC NC S1_WE S1_CS S1_ADDR13 S1_ADDR10 S1_ADDR7 S1_ADDR4 S1_CLK S1_DAT13 S1_DAT10 S1_DAT7 S1_DAT4 S1_DAT1 S1_DAT0 NC NC NC NC A B GF9331 C D E F TOP VIEW GF9331 PIN OUT 328 BGA G H J K L M N P R T U V W Y GND/TGND: 0V VDD_IO: +3.3V VDD_INT: +2.5V NC: No Connection Fig. 1 Top View Pin Out (328-pin BGA) 2 of 24 GENNUM CORPORATION 18303 - 3 PIN DESCRIPTIONS PIN GRID TYPE DESCRIPTION RESET A1 I Active low, asynchronous RESET. Resets all internal logic to default conditions. Should be applied on power up. VCLK_IN F1 I Video input clock. When the input is SDTV the input clock will be 27, 36, 54 or 72MHz. When the input format is HDTV, the input clock will be 74.25 or 74.25/1.001MHz. MEMCLK_IN H1 I Memory clock for SDRAM operation when VLCK_IN > 36MHz. 90MHz input (supplied by an off-chip crystal oscillator). XVOCLK_IN J1 I External video output clock. This input may be used instead of the internal clock doubler for the output clock. XVOCLK_SL H4 I Control signal input. When HIGH, selects external XVOCLK_IN source; when LOW, selects the internal clock doubler for generation of the output clock (required for SD only applications where XVOCLK_IN is used to supply S1_CLK and S2_CLK). Y_IN[9:0] B1,C1,C2,C3,D1,D2, D3,E1,E2,E3 I 8/10-bit input data bus for separate luminance or multiplexed luminance and colour difference video data. When supplying 8-bit data to the GF9331, Y_IN[1:0] will be set LOW and the 8-bit data supplied to Y_IN[9:2]. C_IN[9:0] J3,J4,K1,K2,K3,K4,L4, L3,L2,L1 I 8/10-bit input data bus for colour difference video data. When supplying 8-bit data to the GF9331, C_IN[1:0] will be set LOW and the 8-bit data supplied to C_IN[9:2]. F_IN N2 I Video timing control. F_IN identifies the ODD and EVEN fields in the incoming video signal. F_IN will be LOW in Field 1 and HIGH in Field 2. V_IN N3 I Video timing control. V_IN represents the vertical blanking signal associated with the incoming video signal. V_IN is HIGH during the vertical blanking interval and LOW during active video. H_IN N4 I Video timing control. H_IN represents the horizontal blanking signal associated with the incoming video signal. H_IN is HIGH during horizontal blanking and LOW during active video. FVH_EN N1 I Control signal input. When HIGH, the F_IN, V_IN, and H_IN input pins will be used for video data signaling. When LOW, embedded TRS’s will be detected for video data signaling. VM_MODE M2 I Control signal input. When HIGH, the vertical motion detection is enabled. ED_MODE M1 I Control signal input. When HIGH, the edge direction detection is enabled. STD[4:0] G2,G3,G4,H2,H3 I Video format definition. Defines the video standard when operating without the host interface. See Table 1. STD[4:0] is read into the device on a falling transition of HOST_EN or after a RESET. MODE F3 I Operating mode selection. When HIGH, the GF9331 motion coprocessing is enabled. When LOW, the GF9331 motion co-processing is bypassed. See section 8.0. MODE is read into the device on a falling transition of HOST_EN or after a RESET. HOST_EN E4 I Host interface enable. When set HIGH, the GF9331 is configured through the host interface. When set LOW, the GF9331 is manually configured via input pins. These values are loaded in on the falling transition of HOST_EN. SER_MD G1 I Host interface mode selection. Enables serial mode operation when HIGH. Enables parallel mode operation when LOW. CS P2 I Functions as an active low chip select input for host interface parallel mode operation. Functions as a serial clock input for host interface serial mode operation. 3 of 24 GENNUM CORPORATION 18303 - 3 GF9331 SYMBOL PIN DESCRIPTIONS (Continued) SYMBOL PIN GRID TYPE DESCRIPTION DAT_IO[7:0] R4,R3,R2,R1,T4,T3, T2,T1 I/O R_W P3 I Host interface Read/Write control for parallel mode. A read cycle is defined when HIGH, a write cycle is defined when LOW. A_D P1 I Host interface Address/Data control for parallel mode. The data bus contains an address when HIGH, a data word when LOW. In serial mode, this pin serves as the chip select (active low). Y_OUT[9:0] A20,B20,C20,C19,D20, D19,D18,E20,E19,E18 O Output data bus for separate luminance or multiplexed luminance and colour difference video data. C_OUT[9:0] H20,J20,J19,J18,K20, K19,K18,L18,L19,L20 O Output data bus for colour difference video data. FIL_SEL[3:0] M19,M20,N19,N20 O Filter selection control bus output to the GF9330. The FIL_SEL[3:0] bus is used to switch the GF9330’s internal directional filters on a pixel by pixel basis. H_OUT P20 O Output control signal. H_OUT is a horizontal blanking output. F_OUT T20 O Output control signal. F_OUT is an ODD/EVEN field indicator. V_OUT R20 O Output control signal. V_OUT is a vertical blanking output. S1_CLK Y10 O SDRAM bank 1 clock. S1_CS Y5 O Active low SDRAM chip select for Field Buffer 1. S1_RAS W4 O Active low SDRAM row address strobe for Field Buffer 1. S1_CAS W5 O Active low SDRAM column address strobe for Field Buffer 1. S1_WE Y4 O Active low SDRAM write enable for Field Buffer 1. S1_ADDR[13:0] Y6,W6,V6,Y7,W7,V7, Y8,W8,V8,Y9,W9,V9, W10,V10 O SDRAM address for Field Buffer 1. S1_DAT[15:0] V11,W11,Y11,V12,W12, Y12,V13,W13,Y13,V14, W14,Y14,V15,W15, Y15,Y16 I/O SDRAM data for Field Buffer 1. S2_CLK A9 O SDRAM bank 2 clock. S2_CS A14 O Active low SDRAM chip select for Field Buffer 2. S2_RAS B15 O Active low SDRAM row address strobe for Field Buffer 2. S2_CAS B14 O Active low SDRAM column address strobe for Field Buffer 2. S2_WE A15 O Active low SDRAM write enable for Field Buffer 2. S2_ADDR[13:0] A13,B13,C13,A12,B12, C12,A11,B11,C11,C10, B10,A10,C9,B9 O SDRAM address for Field Buffer 2. S2_DAT[15:0] C8,B8,A8,C7,B7,A7, C6,B6,A6,C5,B5,A5, B4,A4,B3,A3 I/O SDRAM data for Field Buffer 2. TDI U3 I JTAG data input; connect to GND if not used. TMS U2 I JTAG mode select; connect to GND if not used. Host interface bi-directional data bus for parallel mode. In serial mode, DAT_IO[7] serves as the serial data output pin and DAT_IO[0] serves as the serial data input pin. 18303 - 3 GF9331 4 of 24 GENNUM CORPORATION PIN DESCRIPTIONS (Continued) PIN GRID TYPE DESCRIPTION TCLK U1 I JTAG test clock; connect to GND if not used. TDO W1 O JTAG data output. VDD_CLKD F5 NA 2.5 V supply for the internal clock doubler. VSS_CLKD G5 NA Ground connection for the internal clock doubler. VDD_IO E7,E10,E15,F7,F15,J5, J16,M16,N5,R7,R15,T7, T10,T15 NA 3.3 V supply. VDD_INT E6,E12,F6,F16,G6,G16, L5,P16,R6,R16,T6,T12 NA 2.5 V supply. GND / TGND E5,E9,E11,E14,E16, F14,G15,H5,H6, H16,J9,J10,J11,J12,K5, K9,K10,K11,K12,K16, L9,L10,L11,L12,L16, M5,M9,M10,M11,M12, N16,P5,P6,P15,T5,T9, T11,T14,T16,U4,U18, U19,U20,V1,V2 NA Device ground / Thermal ground (electrically equivalent). NC A2,A16,A17,A18,A19, B2,B16,B17,B18,B19, C4,C14,C15,C16,C17, C18,D4,D5,D6,D7,D8, D9,D10,D11,D12,D13, D14,D15,D16,D17,E8, E13,E17,F2,F4,F17, F18,F19,F20,G17,G18, G19,G20,H17,H18, H19,J2,J17,K17,L17, M3,M4,M17,M18,N17, N18,P4,P17,P18,P19, R5,R17,R18,R19,T8, T13,T17,T18,T19,U5, U6,U7,U8,U9,U10,U11, U12,U13,U14,U15,U16, U16,U17,V3,V4,V5,V16, V17,V18,V19,V20,W2, W3,W16,W17,W18, W19,W20,Y1,Y2,Y3, Y17,Y18,Y19,Y20 NA No connection. GF9331 SYMBOL 5 of 24 GENNUM CORPORATION 18303 - 3 ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE Input cells used in the design are able to withstand 3.3V or 5V CMOS input signals, as well as TTL compatible inputs without degrading performance or long-term reliability. VDDIO -0.5 to TBD V VDDCORE -0.5 to TBD V ESD Tolerance Input Voltage Range (any input) VIN -0.5 < VIN < +4.6V The GF9331 has 2kV ESD protection. ESD testing is done in accordance with Gennum’s standard ESD testing procedure. Operating Temperature Range TA 0°C < TA < 70°C Storage Temperature Range TS -40°C < TS < 125°C 3.3V Supply for Device I/0 and 2.5V for Core Logic The GF9331 operates from a single +3.3V supply for device I/O and a single +2.5V supply for core logic. Device I/O Supply Voltage Device Core Supply Voltage Lead Temperature (soldering 10 seconds) 260°C DC ELECTRICAL CHARACTERISTICS VDDIO = 3.0 to 3.6V, VDDCORE = 2.25 to 2.75V, TA = 0 to 70°C, unless otherwise shown PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS NOTES VDDIO +3.0 +3.3 +3.6 V 1 VDDCORE +2.25 +2.5 +2.75 V 1 VDDIO=3.3V ΙDDIO - 43 - mA 1 VDDCORE=2.5V ΙDDCORE - 456 - mA 1 ΙIN=0V or IIN=VDD ΙLEAK - - 10 µA 1 Tristate Leakage Current ΙTRILEAK - - 10 µA 1 Input Logic LOW Voltage VIL - - 0.8 V 1 Input Logic HIGH Voltage VIH 2.1 - - V 1 Device I/O Supply Voltage Device Core Supply Voltage Device I/O Supply Current Device Core Supply Current Input Leakage Current Output Logic LOW Voltage ΙOL= 4mA VOL - 0.2 0.4 V 1 Output Logic HIGH Voltage ΙOH= -4mA VOH 2.7 - - V 1 NOTES: 1. Production, test and QA are performed at room tempature. 6 of 24 GENNUM CORPORATION 18303 - 3 GF9331 SYMBOL 5V Tolerant Inputs AC ELECTRICAL CHARACTERISTICS - Video Interfaces The Video Interface signals include VCLK_IN, Y_IN[9:0], C_IN[9:0], FIL_SEL[3:0], F_IN, V_IN, H_IN, FVH_EN, FF_EN, Y_OUT[9:0], C_OUT[9:0], H_OUT, F_OUT and V_OUT. VDDIO = 3.0 to 3.6V, VDDCORE = 2.25 to 2.75V, TA = 0 to 70°C, unless otherwise shown PARAMETER CONDITIONS MIN TYP MAX UNITS NOTES Clock Input Frequency FHSCI - 74.25 83 MHz 1, 2 Input Data Setup Time tSU 2.5 - - ns 1, 3 Input Data Hold Time tIH 1.5 - - ns 1, 3 40 - 60 % 1 Input Clock Duty Cycle Output Data Delay Time VDDIO=3.6V, CL=15pF load tOD - - 10.0 ns 1 Output Data Hold Time VDDIO=3.6V, CL=15pF load tOH 2.0 - - ns 1 Output Enable Time VDDIO=3.6V, CL=15pF load tOEN - - 10 ns 1 Output Disable Time VDDIO=3.6V, CL=15pF load tODIS - - 10 ns 1 Output Data Rise/Fall Time VDDIO=3.6V, CL=15pF load tODRF - - 2.0 ns 1, 4 GF9331 SYMBOL NOTES: 1. Based on simulation results, verified during device characterization process. 2. Also supports 74.25/1.001MHz. 3. 50% levels. 4. 20% to 80% levels. 7 of 24 GENNUM CORPORATION 18303 - 3 AC ELECTRICAL CHARACTERISTICS - SDRAM Interfaces The SDRAM 1 Interface signals include S1_CLK, S1_CS, S1_RAS, S1_CAS, S1_WE, S1_ADDR[13:0] and S1_DAT[15:0]. The SDRAM 2 Interface signals include S2_CLK, S2_CS, S2_RAS, S2_CAS, S2_WE, S2_ADDR[13:0] and S2_DAT[15:0]. VDDIO = 3.0 to 3.6V, VDDCORE = 2.25 to 2.75V, TA = 0 to 70°C, unless otherwise shown PARAMETER CONDITIONS MIN TYP MAX UNITS NOTES Clock Input Frequency FHSCI_SD - 85 90 MHz 1 Input Data Setup Time tSU_SD 2.0 - - ns 1, 2 Input Data Hold Time tIH_SD 2.5 - - ns 1, 2 40 - 60 % 1 Input Clock Duty Cycle Output Data Delay Time VDDIO=3.6V, CL=15pF load tOD_SD - - 9.1 ns 1 Output Data Hold Time VDDIO=3.6V, CL=15pF load tOH_SD 2.0 - - ns 1 Output Enable Time VDDIO=3.6V, CL=15pF load tOEN_SD - - 20 ns 1, 4 Output Disable Time VDDIO=3.6V, CL=15pF load tODIS_SD - - 20 ns 1, 4 Output Data Rise/Fall Time VDDIO=3.6V, CL=15pF load tODRF_SD - - 2.0 ns 1, 3 GF9331 SYMBOL NOTES: 1. Based on simulation results, verified during device characterization process. 2. 50% levels. 3. 20% to 80% levels. 4. Two clock cycles allocated for data bus turnaround. AC ELECTRICAL CHARACTERISTICS - Host Interface The Host Interface signals include HOST_EN, SER_MD, CS, DAT_IO[7:0], R_W and A_D. VDDIO = 3.0 to 3.6V, VDDCORE = 2.25 to 2.75V, TA = 0 to 70°C, unless otherwise shown SYMBOL MIN TYP MAX UNITS NOTES Clock Input Frequency PARAMETER CONDITIONS FHSCI_HI - - 20 MHz 1 Input Data Setup Time tSU_HI 5 - - ns 1, 2 Input Data Hold Time tIH_HI 1.5 - - ns 1, 2 40 - 60 % 1 Input Clock Duty Cycle Output Data Delay Time VDDIO=3.6V, CL=15pF load tOD_HI - - 10.0 ns 1 Output Data Hold Time VDDIO=3.6V, CL=15pF load tOH_HI 2.0 - - ns 1 Output Enable Time VDDIO=3.6V, CL=15pF load tOEN_HI - - 15 ns 1 Output Disable Time VDDIO=3.6V, CL=15pF load tODIS_HI - - 15 ns 1 Output Data Rise/Fall Time VDDIO=3.6V, CL=15pF load tODRF_HI - - 2.0 ns 1, 3 NOTES: 1. Based on simulation results, verified during device characterization process. 2. 50% levels. 3. 20% to 80% levels. 8 of 24 GENNUM CORPORATION 18303 - 3 DETAILED DEVICE DESCRIPTION 1. INPUT DATA FORMATS GF9331 The GF9331 supports multiple input data formats with multiplexed or separate Y/C channels. Data is supplied to the GF9331 through the Y_IN[9:0] and the C_IN[9:0] busses. Table 1 outlines the data formats that the GF9331 supports according to the setting of STD[4:0] pins or host interface bits, STD[4:0]. Note: For all progressive video standards the GF9331 must be manually set to bypass mode (MODE=0, pin or register). See section 5.0 for host interface details. TABLE 1: Encoding of STD[4:0] for Selecting Input Data Format DESCRIPTION STD STD[4:0] 0 00000 1 00001 2 00010 525i (30/1.001) component 16x9 SMPTE 267M. Multiplexed Y Cb Cr data applied to Y_IN. C_IN should be set LOW. Note: Input clock is 36MHz. 3 00011 RESERVED 4 00100 625i (25Hz) component EBU tech. 3267E.. Multiplexed Y Cb Cr data applied to Y_IN. C_IN should be set LOW. Note: Input clock is 27MHz. 5 00101 RESERVED 6 00110 625i (25Hz) component 16x9 ITU-R BT.601-5 Part B. Multiplexed Y Cb Cr data applied to Y_IN. C_IN should be set LOW. Note: Input clock is 36MHz. 7 00111 RESERVED 8 01000 525p (60/1.001Hz) SMPTE 293M. Y Cb Cr data stream applied to Y_IN. C_IN should be set LOW. Timing information is extracted from embedded TRS sequences. Note: Input clock is 54MHz. 9 01001 RESERVED 10 01010 RESERVED 11 01011 RESERVED 12 01100 625p (50Hz) ITU-R BT.1358. Y Cb Cr data stream applied to Y_IN. C_IN should be set LOW. Timing information is extracted from embedded TRS sequences. Note: Input clock is 54MHz. 13 01101 625p (50Hz) 16 x 9 with 18MHz sampling. Y Cb Cr data stream applied to Y_IN. C_IN should be set LOW. Timing information is extracted from embedded TRS sequences. Note: Input clock is 72MHz. 14 01110 Generic SD input data format with 4:1:1 sampling. Y Cb Cr data is applied to both Y_IN and C_IN. The externally supplied F, V and H signals are used to synchronize the input data stream. Note: Input clock is 27MHz. 15 01111 Generic SD input data format with 4:2:2 sampling and single multiplexed Y Cb Cr input format. Y Cb Cr data applied to Y_IN. C_IN should be set LOW. The externally supplied F, V and H signals are used to synchronize the input data stream. Note: Input clock is 27 or 36MHz. 16 10000 720p (60 & 60/1.001Hz) SMPTE 296M-2001. Y Data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 17 10001 720p (30 & 30/1.001Hz) SMPTE 296M-2001.. Y Data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 18 10010 1080p (30 & 30/1.001Hz) SMPTE 274M. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 525i (30/1.001) component SMPTE 125M.. Multiplexed Y Cb Cr data applied to Y_IN. C_IN should be set LOW. Note: Input clock is 27MHz. RESERVED. 9 of 24 GENNUM CORPORATION 18303 - 3 TABLE 1: Encoding of STD[4:0] for Selecting Input Data Format DESCRIPTION STD[4:0] 19 10011 720p (50Hz) SMPTE 296M-2001. Y Data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 20 10100 1080p (25Hz) SMPTE 274M. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 21 10101 720p (25Hz) SMPTE 296M-2001. Y Data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 22 10110 1080p (24 & 24/1.001Hz) SMPTE 274M. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 23 10111 720p (24 & 24/1.001Hz) SMPTE 296M-2001.. Y Data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 24 11000 1080i (30 & 30/1.001Hz) SMPTE 274M. Y data applied to Y_IN. Cb/Cr data applied to C_IN. Note: Input clock is 74.25 MHz or 74.25/1.001MHz. 25 11001 1080p (30 & 30/1.001Hz in Segmented Frame Format) SMPTE RP211-2000. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 26 11010 1080i (25Hz) SMPTE 274. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 27 11011 1080p (25Hz in Segmented Frame Format) SMPTE RP211-2000. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 28 11100 1080i (25Hz) SMPTE 295M. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 29 11101 1080p ( 24 & 24/1.001Hz in Segmented Frame Format) SMPTE RP211-2000.. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 30 11110 1035i (30Hz) SMPTE 260M. Y data applied to Y_IN. Cb Cr data applied to C_IN. Note: Input clock is 74.25MHz. 31 11111 Generic HD input data format with 4:2:2 sampling and a separate Y/C format. Y Data applied to Y_IN. Cb Cr data applied to C_IN. The externally supplied F_IN, V_IN and H_IN signals are used to synchronize the input data stream. Note: Input clock is 74.25MHz or 74.25/1.001MHz. 2. INPUT SYNCHRONIZATION 2.2 The GF9331 obtains relevant timing information from either embedded TRS information or externally supplied H_IN, V_IN sand F_IN signals. The GF9331 supports generic input data formats with either 4:1:1 or 4:2:2 sampling structures that require up to 2046 active samples per line and have maximum total line width of 4096 (active + blanking) samples. In addition, there is a limit of 2048 lines per interlaced frame. The following host interface parameters are programmable to describe the generic input data format relative to the F_IN, V_IN and H_IN signals. See Figure 2. When FVH_EN is set HIGH using either the host interface or the external pin, the GF9331 relies on the externally supplied H_IN, V_IN and F_IN signals for timing information. When FVH_EN is set LOW, the GF9331 extracts the embedded TRS timing information from the video data stream and ignores any timing information present of the F_IN, V_IN and H_IN pins. 2.1 Support for Both 8-bit and 10-bit Input Data The GF9331 supports 8-bit and 10-bit input data. When operating with 8-bit input data, the two LSBs of the GF9331’s 10-bit input bus should be set LOW and the input data applied to the 8 MSBs of the input bus. Generic Input Format Signaling 2.2.1 H_BLANK_SIZE This parameter defines the number of samples that comprise the horizontal blanking region. This parameter has a maximum value of 4095 and is to be less than the total line width (active + blanking) sample size. Twelve bits within the host interface are dedicated to this parameter. The GF9331 stores and processes active video samples only (i.e. H_IN =0). 10 of 24 GENNUM CORPORATION 18303 - 3 GF9331 STD OUTPUT V H_BLANK_SIZE 0 F 1 0 1 EVEN FIELD ODD FIELD V_BLANK_SIZE_EVEN GF9331 ODD FIELD F_OFFSET_ODD V_OFFSET_ODD ODD FIELD EVEN FIELD V_BLANK_SIZE_ODD EVEN FIELD F_OFFSET_EVEN V_OFFSET_EVEN EVEN FIELD ODD FIELD Fig. 2 Generic Input Format Definition 2.2.2 V_BLANK_SIZE_ODD This parameter defines the number of lines that comprise the vertical blanking interval that follows the odd field. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. The GF9331 stores and processes active video samples only (i.e. V_IN =0). See Figure 2. 2.2.3 V_BLANK_SIZE_EVEN This parameter defines the number of lines that comprise the vertical blanking interval that follows the even field. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. The GF9331 stores and processes active video samples only (i.e. V_IN =0). See Figure 2. Vertical Blanking Region Last active line h v V_OFFSET_ODD/EVEN Fig. 3 V_Offset Definition 11 of 24 GENNUM CORPORATION 18303 - 3 2.2.4 V_OFFSET_ODD 2.2.9 F_POLARITY This parameter defines the number of lines from the V_IN pin EAV transition to the end of the odd active video field region. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. This parameter has been added to accommodate all video decoders which output nonstandard timing for the V _IN signal. See Figure 3. This parameter defines the polarity of the F_IN pin. Refer to Table 2 for F_POLARITY encoding. One bit within the host interface is dedicated to this parameter. This parameter defines the number of lines from the V_IN pin EAV transition to the end of the even active video field region. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. This parameter has been added to accommodate all video decoders which output nonstandard timing for the V_IN signal. See Figure 3. 2.2.6 F_OFFSET_ODD This parameter defines the number of lines from the F_IN pin EAV transition to the vertical blanking interval following the odd field. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. This parameter has been added to accommodate all video decoders which output non-standard timing for the F_IN signal. See Figure 2. 2.2.7 F_OFFSET_EVEN This parameter defines the number of lines from the F_IN pin EAV transition to the vertical blanking interval following the even field. This parameter has a maximum value of 255. Eight bits within the host interface are dedicated to this parameter. This parameter has been added to accommodate all video decoders which output non-standard timing for the F_IN signal. See Figure 2. This parameter defines the polarity of the V_IN pin. With V_POLARITY set LOW, a falling transition on the V_IN pin indicates the end of active video. With V_POLARITY set HIGH, a rising transition on the V_IN pin indicates the end of active video. One bit within the host interface is dedicated to this parameter. 3. SEAMLESS INTERFACE TO THE GF9330 HIGH PERFORMANCE DE-INTERLACER FOR DIRECTIONAL FILTER CONTROL The GF9330 can operate as a stand-alone de-interlacer or can operate in conjunction with the GF9331 Motion Coprocessor. The GF9331 contains adaptive muli-directional edge detectors, as well as a vertical motion detector. Edge sensitive control signals are fed directly to the GF9330. These control signals adaptively switch the GF9330’s internal de-interlacing filters on a pixel by pixel basis. These control signals are fed to the GF9330 by the GF9331 over the FIL_SEL[3:0] control bus. NOTE: The Y_OUT[9:0] pins of the GF9331 must be connected to the Y_IN[9:0] pins of the GF9330. The C_OUT[9:0] pins of the GF9331 must be connected to the C_IN[9:0] pins of the GF9330. The F_OUT, V_OUT and H_OUT pins of the GF9331 must be connected to the F_IN, V_IN and H_IN pins of the GF9330. The FIL_SEL[3:0] output of the GF9331 must be connected to the FIL_SEL[3:0] input of the GF9330. Refer to Figure 4 for a pictorial description of connections between the GF9330 and the GF9331. 2.2.8 H_POLARITY This parameter defines the polarity of the H_IN pin. With H_POLARITY set LOW, a falling transition on the H_IN pin indicates the end of active video. With H_POLARITY set HIGH, a rising transition on the H_IN pin indicates the end of active video. One bit within the host interface is dedicated to this parameter. TABLE 2: F_POLARITY F_POLARITY REGISTER F_IN PIN F_IN PIN FUNCTION 0 0 Even Field 0 1 Odd Field 1 0 Odd Field 1 1 Even Field 12 of 24 GENNUM CORPORATION 18303 - 3 GF9331 2.2.5 V_OFFSET_EVEN 2.2.10 V_POLARITY Y_IN[9:0] GF9331 C_IN[9:0] Y_OUT[9:0] Y_IN[9:0] C_OUT[9:0] C_IN[9:0] FIL_SEL[3:0] FIL_SEL[3:0] Y1_OUT[11:0] C1_OUT[11:0] GF9330 Y2_OUT[11:0] C2_OUT[11:0] GF9331 Fig. 4 Using the GF9331 with the GF9330 for Motion Adaptive De-interalcing with edge and vertical motion detection 4. SEAMLESS INTERFACE TO EXTERNAL SDRAMS 5. HOST INTERFACE The GF9331 requires two independent external field buffers, each implemented with a 1Mx16-bit (min) SDRAM configuration. This configuration supports all operational modes. The following external SDRAM devices are supported for the external field buffer function. The GF9331 provides both serial and parallel host interface control ports for the configuration of internal parameters. The GF9331 is also able to operate in stand-alone mode, with no host interface control. In stand-alone mode, the video standard STD[4:0] and mode of operation MODE (pins or registers, depending on the HOST_EN state). These values are loaded into the device on a falling transition of HOST_EN or after setting RESET LOW. • NEC: uPD4516161AG5, uPD4564163G5, uPD45128163G5 • Micron: MT48LC4M16A2, MT48LC8M16A2 • Samsung: K4S161622C, K4S641632C, K4S281632B Both the serial and parallel interfaces share common pins as described in Table 4. TABLE 4: Host Interface Common Pins GF9331 PIN NAME PARALLEL MODE SERIAL MODE CS CHIP select SCLK - Serial Clock DAT_IO0 Data/address (bit 0) SDI - Serial data in DAT_IO1 Data/address (bit 1) (NOT USED) DAT_IO2 Data/address (bit 2) (NOT USED) DAT_IO3 Data/address (bit 3) (NOT USED) DAT_IO4 Data/address (bit 4) (NOT USED) DAT_IO5 Data/address (bit 5) (NOT USED) DAT_IO6 Data/address (bit 6) (NOT USED) DAT_IO7 Data/address (bit 7) SDO - Serial data out A_D Address/data select SCS - Serial chip select R_W Read/write select (NOT USED) HOST_EN Host Interface enable Host Interface enable SER_MD low = Parallel mode enable high = Serial mode enable 13 of 24 GENNUM CORPORATION 18303 - 3 5.1 Host Interface Serial Mode HIGH or LOW. Before Auto-Configuring the device, the standard and mode must be set using either the host interface (HOST_EN = HIGH) or the external pins (with a falling transition of HOST_EN). This simplifies configuration while allowing customization of many features and format parameters. 5.1.3 Serial Data Word Description The serial data word consists of a 16-bit word as shown in Figure 7. Serial data is transmitted or received MSB first. MSB D15 MASTER (uC) SLAVE (GF9331) uC_SCLK SDI (DAT_IO0) uC_SDI SDO (DAT_IO7) D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 5.1.4 Serial Write Operation Fig.5 Host Interface Serial Mode 5.1.1 Serial Command Word Description The command word consists of a 16-bit word transmitted MSB first and contains a read/write bit, an Auto-Configure control bit, nine reserved bits and a 5-bit address as shown in Figure 6. MSB R/W D11 Fig. 7 Serial Data Word Bit Representation SCS (A_D) uC_SCS D12 Both command and data words are clocked into the GF9331 on the rising edge of the serial clock (SCLK), which may operate in either a continuous or burst fashion. The first bit (MSB) of the serial output (SDO) is available following the last falling SCLK edge of the "read" command word. The remaining bits are clocked out on the falling edges of SCLK. SCLK (CS) uC_SDO LSB D14 D13 All write cycles consist of a command word followed by a data word, both transmitted to the GF9331 via SDI. The first 16-bit word transmitted following a falling transition of SCS is a command word. Several write cycles may be performed while SCS is LOW. See Figure 8. LSB AC RSV RSV RSV RSV RSV RSV RSV RSV RSV A4 A3 A2 A1 A0 Fig. 6 Serial Command Word Bit Representation The R/W bit indicates a Read command if R/W = ‘1’, and a write command when R/W = ‘1’. 5.1.2 Auto-Configure The auto-configure feature will be executed when the Auto-Configure control bit is set (used during write operations only). All Auto-Configure registers will be updated to their appropriate settings based on the current video standard and operational mode. When setting the Auto-Configure bit, the command word should be set with only the AC register bit set to ‘1’. All of the remaining 15 register bits should be set to ‘0’. To complete the Auto-Configuration 16 more data bits must be loaded into the device. The state of these bits can be either 14 of 24 GENNUM CORPORATION 18303 - 3 GF9331 The Gennum Serial Peripheral Interface (GSPI) is a 4 wire interface comprised of serial data in (SDI), serial data out (SDO), an active low serial chip select (SCS), and a clock (SCLK). The interface operates in a master/slave configuration, where the master provides the SCLK, SDI, and SCS signals to the slave or slaves. The master uC_SDO drives the slave(s) SDI input. The SDO pin is a tristate output that allows multiple devices to drive the master uC_SDI. Serial mode operation supports both continuous and burst clock configurations. The interface is illustrated in Figure 5. tSU_HI 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 8 D15 D14 D13 D12 D11 D10 D9 D8 9 10 11 12 13 14 15 SCLK SCS SDI AC R R R R R R R R R A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 SDO Fig. 8 Write Cycle 5.1.5 Serial Read Operation All read cycles consist of a command word transmitted to the GF9331 via SDI followed by a data word transmitted from the GF9331 via SDO. The first 16-bit word transmitted following a falling transition of SCS is a command word. Several read cycles may be performed while SCS is LOW. See Figure 9. tOEN_HI 0 1 2 3 4 5 6 7 8 9 10 11 12 AC 0 R R R R R R R R R A4 A3 13 14 15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SCLK SCS SDI R/W 1 SDO A2 A1 A0 tOD_HI D15 D14 D13 D12 D11 D10 D9 tODIS_HI D8 D7 D6 D5 D4 D3 D2 D1 D0 Fig. 9 Read Cycle 15 of 24 GENNUM CORPORATION 18303 - 3 GF9331 tSU_HI tIH_HI R/W 0 5.2 Host Interface Parallel Mode The Gennum Parallel Peripheral Interface (GPPI) consists of an 8-bit multiplexed address/data bus (DATA_IO[7:0]), a chip select pin (CS), a read/write pin (R_W), and an address/data pin (A_D) as shown in Figure 10. GF9331 MASTER (uC) SLAVE (GF9331) uC_CS CS uC_ADDR/DATA ADDR/DATA (DAT_IO[7:0]) uC_R/W R_W uC_A/D A_D Fig. 10 Host Interface Parallel Mode Data is strobed in/out of the parallel interface on the falling edge of CS. The GF9331 drives the DAT_IO[7:0] bus when the R_W pin is HIGH and the CS pin is LOW, otherwise this port is in a high impedance state. MSB AC LSB RSV RSV A4 A3 A2 A1 A0 5.2.1 Parallel Address Word Description Fig. 11 Parallel Address Word Bit Representation The 8-bit address word loads in the address to be accessed and allows the Auto-Configure bit to be set. The MSB is the Auto-Configure bit, followed by two reserved bits and a 5-bit address as shown in Figure 11. tOEN_HI DAT_IO(7..0) ADDRESS (UB) DATA_IN (LB) DATA_IN tSU_HI ADDRESS (UB) DATA_OUT (LB) DATA_OUT tIH_HI R_W A_D tODIS_HI CS Fig. 12 Write Cycle to the Parallel Interface 5.2.2 Parallel Write Operation A write cycle to the parallel interface is shown in Figure 12. First an 8-bit address word is provided to the DAT_IO port by setting the R_W pin to LOW and A_D pin to HIGH. The MSB of the address word contains an auto-update flag, which allows automatic configuration of predefined registers (used during write operations only). The 5 LSB's of the address word contain the address location for the read or write operation. The remaining address word bits DAT_IO[6:5] are reserved. The address word is registered on the falling edge of CS. Following this, the A_D pin is driven LOW and two data words are sent upper byte (UB) word first and are each clocked in on the falling edge of CS. Two 8-bit data words must follow each address word to occupy each 16-bit parameter which are defined in Table 5. 5.2.3 Parallel Read Operation A read cycle begins with an address write by setting the R_W pin LOW and A_D HIGH. The address is clocked on the falling edge of CS. Following the address, the R_W pin must be driven HIGH and A_D driven LOW to allow the upper byte of data to be clocked out on the first falling edge of CS followed by the lower byte on the second falling edge of CS. 16 of 24 GENNUM CORPORATION 18303 - 3 1D 1C 1B 1A Address 29 Address 28 Address 27 Address 26 Address 25 Address 8 Address 7 Address 6 Address 5 Address 4 Address 3 Address 2 Address 1 Address 0 0 1 2 3 4 5 6 7 8 9 A B C D E F 10 11 12 13 14 15 16 17 18 19 1E Address 30 Address 24 Address 23 Address 22 Address 21 Address 20 Address 19 Address 18 Address 17 Address 16 Address 15 Address 14 Address 13 Address 12 Address 11 Address 10 Address 9 1F Hex H_POLARITY V_POLARITY ID_MODE(1:0) EVEN_LINES_PER_FRAME[1:0] Bit 15 Bit 14 CMD_RESET F_POLARITY PROGRESSIVE_INPUT FIELD2_HAS_TOP_LINE Bit 13 Bit 11 Bit 10 FVH_EN_BIT V_OFFSET_ODD(7:0) F_OFFSET_ODD(7:0) CC_BLANK_START_LINE(7:0) V_BLANK_SIZE_ODD(7:0) FORMAT_SD Bit 12 Bit 9 Bit 8 CC_BLANK_EN Bit 7 Bit 5 Bit 4 Bit 3 MODE CLK_X1_SEL Bit 2 V_OFFESET_EVEN(7:0) F_OFFESET_EVEN(7:0) STD(4:0) CC_BLANK_END_LINE(7:0) V_BLANK_SIZE_EVEN(7:0) NO_LINE_DELAYS(9:0) H_BLANK_SIZE(11:0) Bit 6 GF9331 GENNUM CORPORATION Address 31 EDGE_CTL Bit 1 VM_CTL EXT_MEMCLK_SEL START_OPERATION Bit 0 TABLE 5: Host Interface Register Allocation 17 of 24 18303 - 3 5.3 Control Register Definition The host interface internal registers are divided into two classes: User Configurable (UC) and Auto-Configurable (AC). Address locations 0 through 6 contain parameters which may be configured by the user. Locations 7 through 31 are automatically configured based on the STD[4:0] and MODE registers, but can be user configured if desired. ADDRESS BIT LOCATION 0 4:0 1 2 3 6 REGISTER NAME CLASS DESCRIPTION DEFAULT STD[4:0] UC Defines the video standard as described in Section 1. 00000 5 MODE UC Enables (MODE=1) or bypasses (MODE=0) the GF9331 processing. 0 0 VM_CTL UC Enables (VM_CTL=1) or bypass (VM_CTL=0) vertical motion detection. 0 1 EDGE_CTL UC Enables (EDGE_CTL=1) or bypasses (EDGE_CTL=0) edge detection. 0 6 CC_BLANK_EN UC Enables (CC_BLANK_EN=1) or bypasses (CC_BLANK_EN=0) blanking in the close captioned video region. 0 12 FVH_EN UC Enables the GF9331 to use external F_IN, V_IN, H_IN controls (FVH_EN=1) in place of embedded TRS (FVH_EN=0). 0 13 F_POLARITY UC When set to '1', F_IN follows normal convention where F_IN is '0' for field 1 (odd) and '1' for field 2 (even). 1 14 V_POLARITY UC Defines the polarity of the V_IN pin. When set to '1', V_IN follows normal convention where V_IN is HIGH in the vertical blanking region. 1 15 H_POLARITY UC Defines the polarity of the H_IN pin. When set to '1', H_IN follows normal convention where H_IN is HIGH in the horizontal blanking region. 1 7:0 F_OFFSET_EVEN[7:0] UC Defines the number of lines from the F_IN pin EAV transition to the vertical blanking interval following the even field. This parameter has a maximum value of 255. 00000000 15:8 F_OFFSET_ODD[7:0] UC Defines the number of lines from the F_IN pin EAV transition to the vertical blanking interval following the odd field. This parameter has a maximum value of 255. 00000000 7:0 V_OFFSET_EVEN[7:0] UC Defines the number of lines from the V_IN pin EAV transition to the end of the even active video field region. This parameter has a maximum value of 255. 00000000 15:8 V_OFFSET_ODD[7:0] UC Defines the number of lines from the V_IN pin EAV transition to the end of the odd active video field region. This parameter has a maximum value of 255. 00000000 7:0 CC_BLANK_END_LINE [7:0] UC Defines the last line number at which closed captioned blanking ends. For this parameter, line 0 is defined as the first active line of the field/frame. 00000000 15:8 CC_BLANK_START_LINE [7:0] UC Defines the first line number at which closed captioned blanking starts. For this parameter, line 0 is defined as the first active line of the field/frame. 00000000 18 of 24 GENNUM CORPORATION 18303 - 3 GF9331 CONTROL REGISTER DEFINITIONS CONTROL REGISTER DEFINITIONS (Continued) BIT LOCATION REGISTER NAME CLASS DESCRIPTION DEFAULT 19 7:0 V_BLANK_SIZE_EVEN[7:0] AC Defines the number of lines that comprise the vertical blanking interval that follows the even input field. This parameter has a maximum value of 255. Auto 15:8 V_BLANK_SIZE_ODD[7:0] AC Defines the number of lines that comprise the vertical blanking interval that follows the odd input field. This parameter has a maximum value of 255. Auto 12 FORMAT_SD AC Used to configure the GF9331 SDRAM controller into 8-bit mode for SD video formats. This bit is auto-configured based on the standard and mode selection. Auto 13 PROGRESSIVE_INPUT AC Configures the GF9331 to accept a progressive video format. This bit is auto-configured based on the standard and mode selection. Auto 15:14 ID_MODE[1:0] AC Defines the type of video sequence for input video demultiplexing. When set to "00" the input represents a 4:2:2 sequence, "01" represents a 4:1:1 sequence, and "10" represents an HD format. This word can be auto-configured based on the video standard and mode. Auto 11:0 H_BLANK_SIZE[11:0] AC Defines the number of horizontal blanked input words per line that corresponds to 2 times the number of blanking pixels per line for 4:2:2 SD modes and is equal to the number of pixels per line for HD formats (maximum 4095). This value can be auto-configured. Auto FIELD2_HAS_TOP_LINE AC Set HIGH when field 2, line one is the first line in the video frame (SMPTE 260M). Auto EVEN_LINES_PER_FRAME [1:0] AC Set to 11 for video standards that have an even number of lines per frame such as SMPTE 295M, otherwise set to 00. Auto NO_LINE_DELAYS[9:0] AC Defines the number of line delays to implement within the external field delay. This value is auto-configured based on the standard and mode. The calculation is: NO_LINE_DELAYS = (Number of lines per frame - 3)/2 Auto 21 22 13 15:14 23 9:0 30 0 EXT_MEMCLK_SEL AC Controls the selection of the SDRAM clock source. For VCLK_IN frequencies less than 36MHz, the internal clock doubler can be used. In all other modes an external source is required (MEMCLK_IN). Auto 2 CLK_X1_SEL AC This parameter is normally set for all HD modes and is ‘0’ for all other cases. Auto 15 CMD_RESET UC This parameter forces the GF9331 to enter a reset state. The reset remains in effect until this parameter is cleared with a subsequent command. 0 15 START_OPERATION UC If using external F_IN, V_IN and H_IN signals, this parameter must be set following the completion of programming the F_IN, V_IN and H_IN offsets. 0 31 19 of 24 GENNUM CORPORATION 18303 - 3 GF9331 ADDRESS 6. CLOSED CAPTIONING The GF9331 provides a blanking function for selected input video lines. Consecutive lines within each input field are blanked, when this function is enabled, beginning with the CC_BLANK_START_LINE register and ending with the CC_BLANK_END_LINE register. The blanking is applied prior to any processing of the video data. GF9331 The blanking function is enabled with the CC_BLANK_EN bit. BLANK_START_LINE and BLANK_END_LINE are each allocated 8-bits within the host interface. 7. RESET The RESET pin is an active low pin which will reset all internal logic to it's default conditions when set LOW. On power up it is recommended to reset the device to ensure all internal registers are set to their default state. When applying a reset, the GF9331 will load in the STD[4:0] and MODE[2:0] settings from the external pins. If no further configuration is done, these settings will be used for the operation of the device. 8. MODES OF OPERATION The device supports enabled and disabled modes of operation. The basic operating mode for the GF9331 is selected using the MODE pin or the MODE register within the host interface. See Table 6. 8.1 Motion Processing Mode (MODE=1) When set to operate as a motion co-processor the GF9331 performs edge and vertical motion detection and provides optimal control of the GF9330 filters through the FIL_SEL[3:0] bus on a pixel by pixel basis. 8.2 Disabled Mode (MODE=0) The GF9331 may also be set to disabled mode of operation. In the disabled mode, no motion co-processing operations are performed and the FIL_SEL[3:0] output bus is set to “0000”. In this mode, the input video is still routed to the Y_OUT and C_OUT pins of the GF9330 (Note: Only the active portion of the input video signal is passed through the device to the GF9330, all other data will be lost from the input data stream). See Table 6. TABLE 6: Modes of Operation MODE DESCRIPTION 0 Disabled 1 Motion processing of input video signal 20 of 24 GENNUM CORPORATION 18303 - 3 9. PROCESSING OF INPUT FORMATS The GF9331 provides motion processing for the formats identified in Table 7. TABLE 7: Processing of Input Formats DISABLED MODE 525i (30/1.001) SMPTE 125M Supported Supported 00001 Reserved NA NA 00010 525i (30/1.001) SMPTE 267M - 16x9 Supported Supported 00011 Reserved NA NA 00100 625i (25) EBU Tech 3267 Supported Supported 00101 Reserved NA NA 00110 625i (25) 16 x9 ITU-R BT.601 Part B Supported Supported 00111 Reserved NA NA 01000 525p (60/1.001) SMPTE 293M NA Supported 01001 Reserved NA NA 01010 Reserved NA NA 01011 Reserved NA NA 01100 625p (50) ITU-R BT-1358 NA Supported 01101 625p (50) 16x9 NA Supported 01110 Generic SD 4:1:1 Supported Supported 01111 Generic SD 4:2:2 Supported Supported 10000 720p (60 & 60/1.001) SMPTE 296M-2001 (System #1 and #2) NA Supported 10001 720p (30 & 30/1.001) SMPTE 296M-2001 (System #4 and #5) NA Supported 10010 1080p (30 & 30/1.001) SMPTE 274M (System #7 and #8) NA Supported 10011 720p (50) SMPTE 296M-2001 (System #3) NA Supported 10100 1080p (25) SMPTE 274M (System #9) NA Supported INPUT FORMAT 00000 GF9331 MOTION PROCESSING MODE STD[4:0] 21 of 24 GENNUM CORPORATION 18303 - 3 TABLE 7: Processing of Input Formats (Continued) DISABLED MODE 720p (25) SMPTE 296M-2001 (System #6) NA Supported 10110 1080p (24 & 24/1.001) SMPTE 274M (System #10 and #11) NA Supported 10111 720p (24 & 24/1.001) SMPTE 296M-2001 (System #7 and #8) NA Supported 11000 1080i (30 & 30/1.001) SMPTE 274M (System #4 and #5) Supported Supported 11001 1080PsF (30 & 30/1.001) SMPTE RP211-2000 (System #12 and #13) NA Supported 11010 1080i (25) SMPTE 274M (System #6) Supported Supported 11011 1080PsF (25) SMPTE RP211-2000 (System #14) NA Supported 11100 1080i (25) SMPTE 295M (System #2) Supported Supported 11101 1080PsF (24 & 24/1.001) SMPTE RP211-2000 (System #15 & #16) NA Supported 11110 1035i (30 & 30/1.001) SMPTE 260M Supported Supported 11111 Generic HD 4:2:2 Supported Supported INPUT FORMAT 10101 GF9331 MOTION PROCESSING MODE STD[4:0] 22 of 24 GENNUM CORPORATION 18303 - 3 11.1 EDGE DIRECTION DETECTION FEATURE CONTROL The GF9331 detects objects moving in the vertical direction (e.g. rolling credits). By performing motion detection, a special vertical filter may be enabled within the GF9331 for interpolating the pixels with vertical motion, thereby reducing slow motion de-interlacing artifacts. This vertical motion detection signal is provided to the GF9330 through the control bus (FIL_SEL[3:0]). The GF9331 is able to operate in automatic or disabled mode for edge detection of the video input stream. When set to operate in disabled mode (ED_MODE=0 or EDGE_CTL=0), the internal edge direction detection circuitry is disabled. When set to operate in automatic mode (ED_MODE=1 or EDGE_CTL=1) the GF9331 internally detects edge directions. See Table 9. TABLE 9: 10.1 Vertical Motion Feature Control The GF9331 is able to operate in automatic or disabled mode for vertical motion detection of the video input stream. When set to operate in disabled mode (VM_MODE=0 or VM_CTL=0), the internal vertical motion detection circuitry is disabled. When set to operate in automatic mode (VM_MODE=1 or VM_CTL=1) the GF9331 internally detects vertical motion. See Table 8. TABLE 8: Vertical Motion Control EXTERNAL VM_MODE PIN HOST INTERFACE VM_CTL BIT 0 0 Vertical Motion Detection Disabled 0 1 Vertical Motion Detection Enabled 1 0 1 1 DESCRIPTION EXTERNAL ED_MODE PIN HOST INTERFACE EDGE_CTL BIT 0 0 Edge Direction Detection Disabled 0 1 Edge Direction Detection Enabled 1 0 1 1 DESCRIPTION 12. VIDEO OUTPUT The GF9331 supports all input formats defined in Section 1. Routing of video data to the GF9330 is done via the Y_OUT[9:0] and C_OUT[9:0] busses. Note that only the active portion of the input video signal is passed through the device to the GF9330 unchanged. All other ancillary data is discarded from the input data stream. Timing information is provided by the H_OUT, V_OUT and F_OUT pins. 11. EDGE DIRECTION DETECTION 13. PROCESSING LATENCY In order to reduce the edge artifacts caused by the deinterlacing process, pixel gradients are analysed calculated along different edge directions. The analysis is based on several complex techniques including vertical-temporal filtering, gradient and morphological operations. Edge interpolation filters in the GF9330 are enabled based on the edge information provided by the GF9331 through the FIL_SEL[3:0] control bus. The GF9331 processing latency is constant at 2 lines and 16 pixels for all modes of operation (including bypass). 23 of 24 GENNUM CORPORATION 18303 - 3 GF9331 10. VERTICAL MOTION DETECTION PACKAGE DIMENSIONS 1 2 3 4 5 6 7 8 9 10 11 1213 14 151617 18 19 20 1.27 27.00 ± 0.20 24.00 REF. A B C D E F G H J K L M N P R T U V W Y 4.00, 45˚ (4X) GF9331 A B C D E F G H J K L M N P R T U V W Y 0.75 ± 0.15 (X328) 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1.00 (3X) REF. 24.13 PIN #1 1.27 24.00 REF. 24.13 2.33 ± 0.13 0.60 ± 0.10 1.17 REF. 0.56 REF. 27.00 ± 0.20 CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION REVISION NOTES: Adding row for Tri-state leakage current. - correcting spelling errors - adding 8-bit serial command word diagram. DOCUMENT IDENTIFICATION DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996, Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000, Fax. +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. © Copyright June 2001 Gennum Corporation. All rights reserved. Printed in Canada. 24 of 24 18303 - 3