LM2465 Monolithic Triple 5.5 ns High Gain CRT Driver General Description Features The LM2465 is an integrated high voltage CRT driver circuit designed for use in color monitor applications. The IC contains three high input impedance, wide band amplifiers which directly drive the RGB cathodes of a CRT. Each channel has its gain internally set to −20 and can drive CRT capacitive loads as well as resistive loads present in other applications, limited only by the package’s power dissipation. The IC is packaged in an industry standard 9-lead TO-220 molded plastic package. n Higher gain to match LM126X CMOS preamplifiers n 0V to 3.75V input range n Stable with 0–20 pF capacitive loads and inductive peaking networks n Same pinout as LM2467/8/9, maintaining the standard LM243X Family pinout for easy PCB layout n Convenient TO-220 staggered lead package style Applications n Up to 1280 x 1024 at 75Hz n Pixel clock frequencies up to 135 MHz n Monitors using video blanking Schematic and Connection Diagrams DS200190-2 Note: Tab is at GND Top View Order Number LM2465TA DS200190-1 FIGURE 1. Simplified Schematic Diagram (One Channel) © 2001 National Semiconductor Corporation DS200190 www.national.com LM2465 Monolithic Triple 5.5 ns High Gain CRT Driver March 2001 LM2465 Absolute Maximum Ratings (Notes 1, 3) Machine Model If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Supply Voltage (VCC) Bias Voltage (VBB) Input Voltage (VIN) Storage Temperature Range (TSTG) Lead Temperature (Soldering, < 10 sec.) ESD Tolerance, Human Body Model 250V Operating Ranges (Note 2) VCC +60V to +85V +8V to +15V VBB +0V to +3.75V VIN +15V to +75V VOUT Case Temperature −20˚C to +100˚C Do not operate the part without a heat sink. +90V +16V 0V to 4.5V −65˚C to +150˚C 300˚C 2 kV Electrical Characteristics (See Figure 2 for Test Circuit) Unless otherwise noted: VCC = +80V, VBB = +12V, CL = 8 pF, TC = 50˚C DC Tests: VIN = 2.25VDC AC Tests: Output = 40VPP (25V - 65V) at 1MHz Symbol Parameter Conditions ICC Supply Current All Three Channels, No Input Signal, No Output Load LM2465 Min Typical Max 36 44 Units mA IBB Bias Current All Three Channels 20 24 mA VOUT DC Output Voltage No AC Input Signal, VIN = 1.25V 62 65 68 VDC AV DC Voltage Gain No AC Input Signal −18 −20 −22 ∆AV Gain Matching (Note 4), No AC Input Signal LE Linearity Error (Notes 4, 5), No AC Input Signal tR Rise Time tF OS 1.0 dB 5 % (Note 6), 10% to 90% 5.5 ns Fall Time (Note 6), 90% to 10% 6.0 ns Overshoot (Note 6) 3 % Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Note 2: Operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may change when the device is not operated under the listed test conditions. Note 3: All voltages are measured with respect to GND, unless otherwise specified. Note 4: Calculated value from Voltage Gain test on each channel. Note 5: Linearity Error is the variation in dc gain from VIN = 1.0V to VIN = 3.5V. Note 6: Input from signal generator: tr, tf www.national.com < 1 ns. 2 LM2465 AC Test Circuit DS200190-3 Note: 8 pF load includes parasitic capacitance. FIGURE 2. Test Circuit (One Channel) Figure 2 shows a typical test circuit for evaluation of the LM2465. This circuit is designed to allow testing of the LM2465 in a 50Ω environment without the use of an expensive FET probe. The two 2490Ω resistors form a 200:1 divider with the 50Ω resistor and the oscilloscope. A test point is included for easy use of an oscilloscope probe.The compensation capacitor is used to compensate the stray capacitance of the two 2490Ω resistors to achieve flat frequency response. 3 www.national.com LM2465 Typical Performance Characteristics (VCC = +80VDC, VBB = +12VDC, CL = 8pF, VOUT = 40VPP (25V−65V), Test Circuit - Figure 2 unless otherwise specified) DS200190-7 DS200190-4 FIGURE 6. Power Dissipation vs Frequency FIGURE 3. VOUT vs VIN DS200190-8 DS200190-5 FIGURE 7. Speed vs Offset FIGURE 4. Speed vs Temperature DS200190-6 FIGURE 5. LM2465 Pulse Response DS200190-9 FIGURE 8. Speed vs Load Capacitance www.national.com 4 During normal CRT operation, internal arcing may occasionally occur. Spark gaps, in the range of 200V, connected from the CRT cathodes to CRT ground will limit the maximum voltage, but to a value that is much higher than allowable on the LM2465. This fast, high voltage, high energy pulse can damage the LM2465 output stage. The application circuit shown in Figure 9 is designed to help clamp the voltage at the output of the LM2465 to a safe level. The clamp diodes, D1 and D2, should have a fast transient response, high peak current rating, low series impedance and low shunt capacitance. FDH400 or equivalent diodes are recommended. Do not use 1N4148 diodes for the clamp diodes. D1 and D2 should have short, low impedance connections to VCC and ground respectively. The cathode of D1 should be located very close to a separately decoupled bypass capacitor (C3 in Figure 9). The ground connection of D2 and the decoupling capacitor should be very close to the LM2465 ground. This will significantly reduce the high frequency voltage transients that the LM2465 would be subjected to during an arcover condition. Resistor R2 limits the arcover current that is seen by the diodes while R1 limits the current into the LM2465 as well as the voltage stress at the outputs of the device. R2 should be a 1⁄2W solid carbon type resistor. R1 can be a 1⁄4W metal or carbon film type resistor. Having large value resistors for R1 and R2 would be desirable, but this has the effect of increasing rise and fall times. Inductor L1 is critical to reduce the initial high frequency voltage levels that the LM2465 would be subjected to. The inductor will not only help protect the device but it will also help optimize rise and fall times as well as minimize EMI. For proper arc protection, it is important to not omit any of the arc protection components shown in Figure 9. The LM2465 is a high voltage monolithic three channel CRT driver suitable for high resolution display applications. The LM2465 operates with 80V and 12V power supplies. The part is housed in the industry standard 9-lead TO-220 molded plastic power package. The circuit diagram of the LM2465 is shown in Figure 1. The PNP emitter follower, Q5, provides input buffering. Q1 and Q2 form a fixed gain cascode amplifier with resistors R1 and R2 setting the gain at −20. Emitter followers Q3 and Q4 isolate the high output impedance of the amplifier, decreasing the sensitivity of the device to changes in load capacitance. Q6 provides biasing to the output emitter follower stage to reduce crossover distortion at low signal levels. Figure 2 shows a typical test circuit for evaluation of the LM2465. This circuit is designed to allow testing of the LM2465 in a 50Ω environment without the use of an expensive FET probe. In this test circuit, two low inductance resistors in series totaling 4.95kΩ form a 200:1 wideband, low capacitance probe when connected to a 50Ω coaxial cable and a 50Ω load (such as a 50Ω oscilloscope input). The input signal from the generator is ac coupled to the base of Q5. Application Hints INTRODUCTION National Semiconductor (NSC) is committed to provide application information that assists our customers in obtaining the best performance possible from our products. The following information is provided in order to support this commitment. The reader should be aware that the optimization of performance was done using a specific printed circuit board designed at NSC. Variations in performance can be realized due to physical changes in the printed circuit board and the application. Therefore, the designer should know that component value changes may be required in order to optimize performance in a given application. The values shown in this document can be used as a starting point for evaluation purposes. When working with high bandwidth circuits, good layout practices are also critical to achieving maximum performance. IMPORTANT INFORMATION The LM2465 performance is targeted for the 17“ and low end 19“ monitor market with resolutions up to 1280 X 1024 and a 75Hz refresh rate. It is designed to be a replacement for discrete CRT drivers. The application circuits shown in this document to optimize performance and to protect against damage from CRT arcover are designed specifically for the LM2465. If another member of the LM246X family is used, please refer to its datasheet. POWER SUPPLY BYPASS Since the LM2465 is a wide bandwidth amplifier, proper power supply bypassing is critical for optimum performance. Improper power supply bypassing can result in large overshoot, ringing or oscillation. A 0.1 µF capacitor should be connected from the supply pin, VCC and VBB, to ground, as close to the LM2465 as is practical. Additionally, a 47µF or larger electrolytic capacitor should be connected from both supply pins to ground reasonably close to the LM2465. 5 www.national.com LM2465 ARC PROTECTION Theory of Operation LM2465 Application Hints (Continued) DS200190-10 FIGURE 9. One Channel of the LM2465 with the Recommended Arc Protection Circuit OPTIMIZING TRANSIENT RESPONSE Referring to Figure 9, there are three components (R1, R2 and L1) that can be adjusted to optimize the transient response of the application circuit. Increasing the values of R1 and R2 will slow the circuit down while decreasing overshoot. Increasing the value of L1 will speed up the circuit as well as increase overshoot. It is very important to use inductors with very high self-resonant frequencies, preferably above 300MHz. Ferrite core inductors from J.W. Miller Magnetics (part # 78FR--k) were used for optimizing the performance of the device in the NSC application board. The values shown in Figure 9 can be used as a good starting point for the evaluation of the LM2465. Using a variable resistor for R1 will simplify finding the value needed for optimum performance in a given application. Once the optimum value is determined, the variable resistors can be replaced with fixed values. the device is assumed to be sitting at the black level (65V in this case). This graph gives the designer the information needed to determine the heat sink requirement for his application. The designer should note that if the load capacitance is increased, the AC component of the total power dissipation will also increase. The LM2465 case temperature must be maintained below 100˚C. If the maximum expected ambient temperature is 70˚C and the maximum power dissipation is 7.6W (from Figure 6, 75MHz bandwidth) then a maximum heat sink thermal resistance can be calculated: This example assumes a capacitive load of 8pF and no resistive load. TYPICAL APPLICATION A typical application of the LM2465 is shown in Figure 10 and Figure 11. Used in conjunction with an LM1267 and a LM2479/2480bias clamp, a complete video channel from monitor input to CRT cathode can be achieved. Performance is ideal for 1280 x 1024 resolution displays with pixel clock frequencies up to 135 MHz. Figure 10 and Figure 11 are the schematic for the NSC demonstration board that can be used to evaluate the LM1267/2465 /2480 combination in a monitor. EFFECT OF LOAD CAPACITANCE Figure 8 shows the effect of increased load capacitance on the speed of the device. This demonstrates the importance of knowing the load capacitance in the application. The rise time increased about 0.12nsec for an increase of 1pF in the load capacitance. The fall time increased about 0.10 nsec for a 1pF increase in the load capacitance. EFFECT OF OFFSET Figure 7 shows the variation in rise and fall times when the output offset of the device is varied from 40 to 50 VDC. The rise time increases less than 0.20nsec from its fastest point near 45V. The fall time becomes faster as the offset voltage increases, but the 45V offset is only 0.1nsec slower than the fastest fall time. PC BOARD LAYOUT CONSIDERATIONS For optimum performance, an adequate ground plane, isolation between channels, good supply bypassing and minimizing unwanted feedback are necessary. Also, the length of the signal traces from the preamplifier to the LM2465 and from the LM2465 to the CRT cathode should be as short as possible. The following references are recommended: Ott, Henry W., “Noise Reduction Techniques in Electronic Systems”, John Wiley & Sons, New York, 1976. “Video Amplifier Design for Computer Monitors”, National Semiconductor Application Note 1013. Pease, Robert A., “Troubleshooting Analog Circuits”, Butterworth-Heinemann, 1991. Because of its high small signal bandwidth, the part may oscillate in a monitor if feedback occurs around the video channel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input circuit wiring should be spaced as far as possible from output circuit wiring. THERMAL CONSIDERATIONS Figure 4 shows the performance of the LM2465 in the test circuit shown in Figure 2 as a function of case temperature. The figure shows that the rise time of the LM2465 increases by approximately 13% as the case temperature increases from 30˚C to 95˚C. This corresponds to a speed degradation of 2% for every 10˚C rise in case temperature. The fall time degrades around 0.3% for every 10˚C rise in case temperature. Figure 6 shows the maximum power dissipation of the LM2465 vs. Frequency when all three channels of the device are driving an 8pF load with a 40Vp-p alternating one pixel on, one pixel off signal. The graph assumes a 72% active time (device operating at the specified frequency) which is typical in a monitor application. The other 28% of the time www.national.com 6 LM2465 Application Hints (Continued) NSC DEMONSTRATION BOARD Figure 12 shows the routing and component placement on the NSC LM126X/246X/LM2479/80 demonstration board. The schematic of the board is shown in Figure 10 and Figure 11. This board provides a good example of a layout that can be used as a guide for future layouts. Note the location of the following components: • C16, C19 — VCC bypass capacitor, located very close to pin 4 and ground pins • C17, C20 — VBB bypass capacitors, located close to pin 8 and ground • C46, C47, C48 — VCC bypass capacitors, near LM2465 and VCC clamp diodes. Very important for arc protection. The routing of the LM2465 outputs to the CRT is very critical to achieving optimum performance. Figure 13 shows the routing and component placement from pin 3 of the LM2465 to the blue cathode. Note that the components are placed so that they almost line up from the output pin of the LM2465 to the blue cathode pin of the CRT connector. This is done to minimize the length of the video path between these two components. Note also that D8, D9, R24 and D6 are placed to minimize the size of the video nodes that they are attached to. This minimizes parasitic capacitance in the video path and also enhances the effectiveness of the protection diodes. The anode of protection diode D8 is connected directly to a section of the the ground plane that has a short and direct path to the LM2465 ground pins. The cathode of D9 is connected to VCC very close to decoupling capacitor C48 (see Figure 13) which is connected to the same section of the ground plane as D8. The diode placement and routing is very important for minimizing the voltage stress on the LM2465 during an arcover event. Lastly, notice that S3 is placed very close to the blue cathode and is tied directly to CRT ground. 7 www.national.com FIGURE 10. LM126X/LM246X Demonstration Board Schematic DS200190-11 LM2465 Application Hints www.national.com (Continued) 8 DS200190-15 (Continued) LM2465 FIGURE 11. LM126X/LM246X Demonstration Board Schematic (continued) Application Hints 9 www.national.com LM2465 Application Hints (Continued) DS200190-13 FIGURE 12. LM126X/LM246X Demo Board Layout www.national.com 10 LM2465 Application Hints (Continued) DS200190-14 FIGURE 13. Trace Routing and Component Placement for Blue Channel Output 11 www.national.com LM2465 Monolithic Triple 5.5 ns High Gain CRT Driver Physical Dimensions inches (millimeters) unless otherwise noted CONTROLLING DIMENSION IS INCH VALUES IN [ ] ARE MILLIMETERS NS Package Number TA09A Order Number LM2465TA LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.