ETC LM317AK

LM117/LM317A/LM317
3-Terminal Adjustable Regulator
General Description
The LM117 series of adjustable 3-terminal positive voltage
regulators is capable of supplying in excess of 1.5A over a
1.2V to 37V output range. They are exceptionally easy to
use and require only two external resistors to set the output
voltage. Further, both line and load regulation are better than
standard fixed regulators. Also, the LM117 is packaged in
standard transistor packages which are easily mounted and
handled.
In addition to higher performance than fixed regulators, the
LM117 series offers full overload protection available only in
IC’s. Included on the chip are current limit, thermal overload
protection and safe area protection. All overload protection
circuitry remains fully functional even if the adjustment terminal is disconnected.
Normally, no capacitors are needed unless the device is situated more than 6 inches from the input filter capacitors in
which case an input bypass is needed. An optional output
capacitor can be added to improve transient response. The
adjustment terminal can be bypassed to achieve very high
ripple rejection ratios which are difficult to achieve with standard 3-terminal regulators.
Besides replacing fixed regulators, the LM117 is useful in a
wide variety of other applications. Since the regulator is
“floating” and sees only the input-to-output differential volt-
Typical Applications
age, supplies of several hundred volts can be regulated as
long as the maximum input to output differential is not exceeded, i.e., avoid short-circuiting the output.
Also, it makes an especially simple adjustable switching
regulator, a programmable output regulator, or by connecting
a fixed resistor between the adjustment pin and output, the
LM117 can be used as a precision current regulator. Supplies with electronic shutdown can be achieved by clamping
the adjustment terminal to ground which programs the output to 1.2V where most loads draw little current.
For applications requiring greater output current, see LM150
series (3A) and LM138 series (5A) data sheets. For the
negative complement, see LM137 series data sheet.
Features
n
n
n
n
n
n
n
n
n
Guaranteed 1% output voltage tolerance (LM317A)
Guaranteed max. 0.01%/V line regulation (LM317A)
Guaranteed max. 0.3% load regulation (LM117)
Guaranteed 1.5A output current
Adjustable output down to 1.2V
Current limit constant with temperature
P+ Product Enhancement tested
80 dB ripple rejection
Output is short-circuit protected
LM117 Series Packages
Part Number
1.2V–25V Adjustable Regulator
Suffix
Design
Package
Load
Current
DS009063-1
Full output current not available at high input-output voltages
*Needed if device is more than 6 inches from filter capacitors.
†Optional — improves transient response. Output capacitors in the range
of 1 µF to 1000 µF of aluminum or tantalum electrolytic are commonly
used to provide improved output impedance and rejection of transients.
K
TO-3
1.5A
H
TO-39
0.5A
T
TO-220
1.5A
E
LCC
0.5A
1.5A
S
TO-263
EMP
SOT-223
1A
MDT
TO-252
0.5A
SOT-223 vs D-Pak (TO-252)
Packages
DS009063-54
Scale 1:1
© 1999 National Semiconductor Corporation
This Material Copyrighted by Its Respective Manufacturer
DS009063
www.national.com
LM117/LM317A/LM317 3-Terminal Adjustable Regulator
August 1999
Absolute Maximum Ratings (Note 1)
Operating Temperature Range
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
LM117
LM317A
LM317
Power Dissipation
Internally Limited
Input-Output Voltage Differential
+40V, −0.3V
Storage Temperature
−65˚C to +150˚C
Lead Temperature
Metal Package (Soldering, 10 seconds)
300˚C
Plastic Package (Soldering, 4 seconds)
260˚C
ESD Tolerance (Note 5)
3 kV
−55˚C ≤ TJ ≤ +150˚C
−40˚C ≤ TJ ≤ +125˚C
0˚C ≤ TJ ≤ +125˚C
Preconditioning
Thermal Limit Burn-In
All Devices 100%
Electrical Characteristics (Note 3)
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA.
Parameter
Conditions
LM117 (Note 2)
Units
Min
Typ
Max
1.20
1.25
1.30
V
Reference Voltage
V
3V ≤ (VIN − VOUT) ≤ 40V,
10 mA ≤ IOUT ≤ IMAX, P ≤ PMAX
Line Regulation
Load Regulation
Thermal Regulation
3V ≤ (VIN − VOUT) ≤ 40V (Note 4)
0.01
0.02
%/V
0.02
0.05
%/V
0.1
0.3
%
0.3
1
%
20 ms Pulse
0.03
0.07
%/W
50
100
µA
10 mA ≤ IOUT ≤ IMAX
0.2
5
µA
3.5
5
mA
1.5
2.2
3.4
A
0.5
0.8
1.8
A
10 mA ≤ IOUT ≤ IMAX (Note 4)
Adjustment Pin Current
Adjustment Pin Current Change
3V ≤ (VIN − VOUT) ≤ 40V
Minimum Load Current
TMIN ≤ TJ ≤ TMAX
(VIN − VOUT) = 40V
Current Limit
(VIN − VOUT) ≤ 15V
Temperature Stability
K Package
H Packages
(VIN − VOUT) = 40V
K Package
H Package
RMS Output Noise, % of VOUT
Ripple Rejection Ratio
%
1
0.3
0.4
A
0.15
0.2
A
10 Hz ≤ f ≤ 10 kHz
VOUT = 10V, f = 120 Hz,
CADJ = 0 µF
VOUT = 10V, f = 120 Hz,
CADJ = 10 µF
66
0.003
%
65
dB
80
dB
Long-Term Stability
TJ = 125˚C, 1000 hrs
0.3
1
%
Thermal Resistance,
K Package
2.3
3
˚C/W
Junction-to-Case
H Package
12
15
˚C/W
E Package
˚C/W
Thermal Resistance, Junction-
K Package
35
˚C/W
to-Ambient (No Heat Sink)
H Package
140
˚C/W
E Package
www.national.com
This Material Copyrighted by Its Respective Manufacturer
˚C/W
2
Electrical Characteristics (Note 3)
Specifications with standard type face are for TJ = 25˚C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN − VOUT = 5V, and IOUT = 10 mA.
Parameter
Conditions
LM317A
Reference Voltage
3V ≤ (VIN − VOUT) ≤ 40V,
LM317
Min
Typ
Max
1.238
1.250
1.262
1.225
1.250
1.270
Units
Min
Typ
Max
1.20
1.25
1.30
V
V
10 mA ≤ IOUT ≤ IMAX, P ≤ PMAX
Line Regulation
Load Regulation
Thermal Regulation
3V ≤ (VIN − VOUT) ≤ 40V (Note 4)
0.005
0.01
0.01
0.04
%/V
0.01
0.02
0.02
0.07
%/V
0.1
0.5
0.1
0.5
%
0.3
1
0.3
1.5
%
20 ms Pulse
0.04
0.07
0.04
0.07
%/W
50
100
50
100
µA
10 mA ≤ IOUT ≤ IMAX
0.2
5
0.2
5
µA
10
3.5
10
mA
10 mA ≤ IOUT ≤ IMAX (Note 4)
Adjustment Pin Current
Adjustment Pin Current
Change
3V ≤ (VIN − VOUT) ≤ 40V
Minimum Load Current
TMIN ≤ TJ ≤ TMAX
(VIN − VOUT) = 40V
Current Limit
(VIN − VOUT) ≤ 15V
Temperature Stability
1
3.5
K, T, S Packages
1.5
2.2
3.4
1.5
2.2
3.4
A
H Package
MP Package
(VIN − VOUT) = 40V
0.5
1.5
0.8
2.2
1.8
3.4
0.5
1.5
0.8
2.2
1.8
3.4
A
A
K, T, S Packages
H Package
MP Package
RMS Output Noise, % of VOUT
Ripple Rejection Ratio
0.15
0.4
0.15
0.4
A
0.075
0.55
0.2
0.4
0.075
0.15
0.2
0.4
A
A
10 Hz ≤ f ≤ 10 kHz
VOUT = 10V, f = 120 Hz,
CADJ = 0 µF
VOUT = 10V, f = 120 Hz,
CADJ = 10 µF
Long-Term Stability
TJ = 125˚C, 1000 hrs
Thermal Resistance,
Junction-to-Case
K Package
MDT Package
66
0.003
0.003
%
65
65
dB
80
dB
80
0.3
H Package
T Package
MP Package
Thermal Resistance,
Junction-to-Ambient (No Heat
Sink)
%
1
66
1
0.3
1
%
2.3
5
3
˚C/W
˚C/W
15
12
15
12
4
23.5
5
4
23.5
˚C/W
˚C/W
˚C/W
K Package
MDT Package(Note 6)
35
35
92
˚C/W
˚C/W
H Package
140
140
˚C/W
T Package
50
50
˚C/W
S Package (Note 6)
50
50
˚C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed.
Note 2: Refer to RETS117H drawing for the LM117H, or the RETS117K for the LM117K military specifications.
Note 3: Although power dissipation is internally limited, these specifications are applicable for maximum power dissipations of 2W for the TO-39 and SOT-223 and
20W for the TO-3, TO-220, and TO-263. IMAX is 1.5A for the TO-3, TO-220, and TO-263 packages, 0.5A for the TO-39 package and 1A for the SOT-223 Package.
All limits (i.e., the numbers in the Min. and Max. columns) are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 4: Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are
covered under the specifications for thermal regulation.
Note 5: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 6: If the TO-263 or TO-252 packages are used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the
package. If the SOT-223 package is used, the thermal resistance can be reduced by increasing the PC board copper area (see applications hints for heatsinking).
3
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Typical Performance Characteristics
Output Capacitor = 0 µF unless otherwise noted
Current Limit
Load Regulation
Adjustment Current
DS009063-37
Dropout Voltage
DS009063-38
Temperature Stability
DS009063-40
Ripple Rejection
DS009063-41
DS009063-44
Line Transient Response
4
DS009063-45
Load Transient Response
DS009063-47
DS009063-46
This Material Copyrighted by Its Respective Manufacturer
DS009063-42
Ripple Rejection
DS009063-43
www.national.com
Minimum Operating Current
Ripple Rejection
Output Impedance
DS009063-39
DS009063-48
aluminum electrolytic) on the output swamps this effect and
insures stability. Any increase of the load capacitance larger
than 10 µF will merely improve the loop stability and output
impedance.
Application Hints
In operation, the LM117 develops a nominal 1.25V reference
voltage, VREF, between the output and adjustment terminal.
The reference voltage is impressed across program resistor
R1 and, since the voltage is constant, a constant current I1
then flows through the output set resistor R2, giving an output voltage of
Load Regulation
The LM117 is capable of providing extremely good load
regulation but a few precautions are needed to obtain maximum performance. The current set resistor connected between the adjustment terminal and the output terminal (usually 240Ω) should be tied directly to the output (case) of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05Ω resistance between the regulator and load will have a
load regulation due to line resistance of 0.05Ω x IL. If the set
resistor is connected near the load the effective line resistance will be 0.05Ω (1 + R2/R1) or in this case, 11.5 times
worse.
Figure 2 shows the effect of resistance between the regulator and 240Ω set resistor.
DS009063-5
FIGURE 1.
Since the 100 µA current from the adjustment terminal represents an error term, the LM117 was designed to minimize
IADJ and make it very constant with line and load changes.
To do this, all quiescent operating current is returned to the
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise.
DS009063-6
FIGURE 2. Regulator with Line Resistance in Output
Lead
External Capacitors
An input bypass capacitor is recommended. A 0.1 µF disc or
1 µF solid tantalum on the input is suitable input bypassing
for almost all applications. The device is more sensitive to
the absence of input bypassing when adjustment or output
capacitors are used but the above values will eliminate the
possibility of problems.
The adjustment terminal can be bypassed to ground on the
LM117 to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is
increased. With a 10 µF bypass capacitor 80 dB ripple rejection is obtainable at any output level. Increases over 10 µF
do not appreciably improve the ripple rejection at frequencies above 120 Hz. If the bypass capacitor is used, it is
sometimes necessary to include protection diodes to prevent
the capacitor from discharging through internal low current
paths and damaging the device.
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. However, with the TO-39 package, care should
be taken to minimize the wire length of the output lead. The
ground of R2 can be returned near the ground of the load to
provide remote ground sensing and improve load regulation.
Protection Diodes
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator. Most 10 µF capacitors have low enough
internal series resistance to deliver 20A spikes when
shorted. Although the surge is short, there is enough energy
to damage parts of the IC.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the regulator, and the rate of decrease of VIN. In the LM117, this discharge path is through a large junction that is able to sustain
15A surge with no problem. This is not true of other types of
positive regulators. For output capacitors of 25 µF or less,
there is no need to use diodes.
The bypass capacitor on the adjustment terminal can discharge through a low current junction. Discharge occurs
when either the input or output is shorted. Internal to the
LM117 is a 50Ω resistor which limits the peak discharge current. No protection is needed for output voltages of 25V or
In general, the best type of capacitors to use is solid tantalum. Solid tantalum capacitors have low impedance even at
high frequencies. Depending upon capacitor construction, it
takes about 25 µF in aluminum electrolytic to equal 1 µF
solid tantalum at high frequencies. Ceramic capacitors are
also good at high frequencies; but some types have a large
decrease in capacitance at frequencies around 0.5 MHz. For
this reason, 0.01 µF disc may seem to work better than a 0.1
µF disc as a bypass.
Although the LM117 is stable with no output capacitors, like
any feedback circuit, certain values of external capacitance
can cause excessive ringing. This occurs with values between 500 pF and 5000 pF. A 1 µF solid tantalum (or 25 µF
5
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Application Hints
As a design aid, Figure 5 shows the maximum allowable
power dissipation compared to ambient temperature for the
TO-263 device (assuming θ(J−A) is 35˚C/W and the maximum junction temperature is 125˚C).
(Continued)
less and 10 µF capacitance. Figure 3 shows an LM117 with
protection diodes included for use with outputs greater than
25V and high values of output capacitance.
DS009063-7
DS009063-56
FIGURE 5. Maximum Power Dissipation vs TAMB for
the TO-263 Package
D1 protects against C1
D2 protects against C2
Figure 6 and Figure 7 show the information for the SOT-223
package. Figure 7 assumes a θ(J−A) of 74˚C/W for 1 ounce
copper and 51˚C/W for 2 ounce copper and a maximum
junction temperature of 125˚C.
FIGURE 3. Regulator with Protection Diodes
When a value for θ(H−A) is found using the equation shown,
a heatsink must be selected that has a value that is less than
or equal to this number.
θ(H−A) is specified numerically by the heatsink manufacturer
in the catalog, or shown in a curve that plots temperature rise
vs power dissipation for the heatsink.
HEATSINKING TO-263, SOT-223 AND TO-252 PACKAGE
PARTS
The TO-263 (“S”), SOT-223 (“MP”) and TO-252 (”DT”) packages use a copper plane on the PCB and the PCB itself as
a heatsink. To optimize the heat sinking ability of the plane
and PCB, solder the tab of the package to the plane.
Figure 4 shows for the TO-263 the measured values of θ(J−A)
for different copper area sizes using a typical PCB with 1
ounce copper and no solder mask over the copper area used
for heatsinking.
DS009063-57
FIGURE 6. θ(J−A) vs Copper (2 ounce) Area for the
SOT-223 Package
DS009063-55
FIGURE 4. θ(J−A) vs Copper (1 ounce) Area for the
TO-263 Package
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. It should also
be observed that the minimum value of θ(J−A) for the TO-263
package mounted to a PCB is 32˚C/W.
www.national.com
This Material Copyrighted by Its Respective Manufacturer
DS009063-58
FIGURE 7. Maximum Power Dissipation vs TAMB for
the SOT-223 Package
6
Application Hints
The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):
TR(max) = TJ(max) − TA(max)
(Continued)
The LM317 regulators have internal thermal shutdown to
protect the device from over-heating. Under all possible operating conditions, the junction temperature of the LM317
must be within the range of 0˚C to 125˚C. A heatsink may be
required depending on the maximum power dissipation and
maximum ambient temperature of the application. To determine if a heatsink is needed, the power dissipated by the
regulator, PD, must be calculated:
IIN = IL + IG
PD = (VIN − VOUT) IL + VINIG
Figure 8 shows the voltage and currents which are present in
the circuit.
where TJ(max) is the maximum allowable junction temperature (125˚C), and TA(max) is the maximum ambient temperature which will be encountered in the application.
Using the calculated values for TR(max) and PD, the maximum allowable value for the junction-to-ambient thermal resistance (θJA) can be calculated:
θJA = TR(max)/PD
If the maximum allowable value for θJA is found to be
≥92˚C/W (Typical Rated Value) for TO-252 package, no
heatsink is needed since the package alone will dissipate
enough heat to satisfy these requirements. If the calculated
value for θJA falls below these limits, a heatsink is required.
As a design aid, Table 1 shows the value of the θJA of
TO-252 for different heatsink area. The copper patterns that
we used to measure these θJAs are shown at the end of the
Application Notes Section. Figure 9 reflects the same test results as what are in the Table 1
Figure 10 shows the maximum allowable power dissipation
vs. ambient temperature for the TO-252 device. Figure 11
shows the maximum allowable power dissipation vs. copper
area (in2) for the TO-252 device. Please see AN1028 for
power enhancement techniques to be used with SOT-223
and TO-252 packages.
DS009063-60
FIGURE 8. Power Dissipation Diagram
TABLE 1. θJA Different Heatsink Area
Layout
Copper Area
Thermal Resistance
Top Side (in2)*
Bottom Side (in2)
(θJA˚C/W) TO-252
1
0.0123
0
103
2
0.066
0
87
3
0.3
0
60
4
0.53
0
54
5
0.76
0
52
6
1
0
47
7
0
0.2
84
8
0
0.4
70
9
0
0.6
63
10
0
0.8
57
11
0
1
57
12
0.066
0.066
89
13
0.175
0.175
72
14
0.284
0.284
61
15
0.392
0.392
55
16
0.5
0.5
53
Note: * Tab of device attached to topside of copper.
7
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Application Hints
(Continued)
DS009063-61
FIGURE 9. θJA vs 2oz Copper Area for TO-252
DS009063-63
FIGURE 10. Maximum Allowable Power Dissipation vs. Ambient Temperature for TO-252
DS009063-62
FIGURE 11. Maximum Allowable Power Dissipation vs. 2oz Copper Area for TO-252
www.national.com
This Material Copyrighted by Its Respective Manufacturer
8
Application Hints
(Continued)
DS009063-64
FIGURE 12. Top View of the Thermal Test Pattern in Actual Scale
9
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Application Hints
(Continued)
DS009063-65
FIGURE 13. Bottom View of the Thermal Test Pattern in Actual Scale
www.national.com
This Material Copyrighted by Its Respective Manufacturer
10
Schematic Diagram
DS009063-8
Typical Applications
5V Logic Regulator with Electronic Shutdown*
Slow Turn-On 15V Regulator
DS009063-9
DS009063-3
*Min. output ) 1.2V
11
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Typical Applications
(Continued)
High Stability 10V Regulator
Adjustable Regulator with Improved Ripple Rejection
DS009063-10
†Solid tantalum
*Discharges C1 if output is shorted to ground
DS009063-11
High Current Adjustable Regulator
DS009063-12
‡ Optional — improves ripple rejection
†Solid tantalum
*Minimum load current = 30 mA
www.national.com
This Material Copyrighted by Its Respective Manufacturer
12
Typical Applications
(Continued)
Power Follower
0 to 30V Regulator
DS009063-13
DS009063-14
Full output current not available at high input-output voltages
5A Constant Voltage/Constant Current Regulator
DS009063-15
†Solid tantalum
*Lights in constant current mode
13
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Typical Applications
1A Current Regulator
(Continued)
1.2V–20V Regulator with Minimum
Program Current
High Gain Amplifier
DS009063-16
DS009063-17
*Minimum load current ) 4 mA
DS009063-18
Low Cost 3A Switching Regulator
DS009063-19
†Solid tantalum
*Core — Arnold A-254168-2 60 turns
www.national.com
This Material Copyrighted by Its Respective Manufacturer
14
Typical Applications
(Continued)
4A Switching Regulator with Overload Protection
DS009063-20
†Solid tantalum
*Core — Arnold A-254168-2 60 turns
Precision Current Limiter
DS009063-21
Tracking Preregulator
DS009063-22
15
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Typical Applications
(Continued)
Current Limited Voltage Regulator
DS009063-23
(Compared to LM117’s higher current limit)
— At 50 mA output only 3⁄4 volt of drop occurs in R3 and R4
Adjusting Multiple On-Card Regulators with Single Control*
DS009063-24
*All outputs within ± 100 mV
†Minimum load — 10 mA
AC Voltage Regulator
DS009063-25
www.national.com
This Material Copyrighted by Its Respective Manufacturer
16
Typical Applications
(Continued)
12V Battery Charger
DS009063-26
Use of RS allows low charging rates with fully charged battery.
50 mA Constant Current Battery Charger
DS009063-27
Adjustable 4A Regulator
DS009063-28
17
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Typical Applications
(Continued)
Digitally Selected Outputs
Current Limited 6V Charger
DS009063-29
*Sets peak current (0.6A for 1Ω)
**The 1000 µF is recommended to filter out input transients
www.national.com
This Material Copyrighted by Its Respective Manufacturer
DS009063-2
*Sets maximum VOUT
18
Connection Diagrams
(TO-3)
Metal Can Package
(TO-39)
Metal Can Package
(TO-220)
Plastic Package
DS009063-31
CASE IS OUTPUT
DS009063-30
CASE IS OUTPUT
Bottom View
Steel Package
Order Number LM117K STEEL
or LM317K STEEL
See NS Package Number K02A
Order Number LM117K/883
See NS Package Number K02C
Bottom View
Order Number LM117H,
LM117H/883,
LM317AH or LM317H
See NS Package Number H03A
DS009063-32
Front View
Order Number LM317AT or LM317T
See NS Package Number T03B
(TO-263) Surface-Mount Package
Ceramic Leadless
Chip Carrier
DS009063-36
Side View
Order Number LM317S
See NS Package Number TS3B
DS009063-35
Top View
DS009063-34
Top View
Order Number LM117E/883
See NS Package Number E20A
3-Lead SOT-223
TO-252 (D-Pak)
DS009063-59
Front View
Order Part Number LM317EMP or
LM317AEMP
Package Marked N01A
See NSC Package Number MA04A
DS009063-66
Front View
Order Part Number LM317DT
See NSC Package Number TD03B
19
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Physical Dimensions
inches (millimeters) unless otherwise noted
Ceramic Leadless Chip Carrier
Order Number LM117E/883
NS Package Number E20A
www.national.com
This Material Copyrighted by Its Respective Manufacturer
20
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
(TO-39) Metal Can Package
Order Number LM117H, LM117H/883, LM317AH or LM317H
NS Package Number H03A
TO-3 Metal Can Package (K)
Order Number LM117K STEEL,
LM117K STEEL/883, or LM317K STEEL
NS Package Number K02A
21
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
TO-3 Metal Can Package (K)
Mil-Aero Product
Order Number LM117K/883
NS Package Number K02C
www.national.com
This Material Copyrighted by Its Respective Manufacturer
22
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead SOT-223 Package
Order Number LM317AEMP or LM317EMP
NS Package Number MA04A
23
This Material Copyrighted by Its Respective Manufacturer
www.national.com
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
(TO-220) Outline Drawing
Order Number LM317AT or LM317T
NS Package Number T03B
www.national.com
This Material Copyrighted by Its Respective Manufacturer
24
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
Order Number LM317S
NS Package Number TS3B
25
This Material Copyrighted by Its Respective Manufacturer
www.national.com
LM117/LM317A/LM317 3-Terminal Adjustable Regulator
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
Order Number LM317MDT
NS Package Number TD03B
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
This Material Copyrighted by Its Respective Manufacturer