AD AD9884A

a
FEATURES
140 MSPS Maximum Conversion Rate
500 MHz Analog Bandwidth
0.5 V to 1.0 V Analog Input Range
400 ps p-p PLL Clock Jitter
Power-Down Mode
3.3 V Power Supply
2.5 V to 3.3 V Three-State CMOS Outputs
Demultiplexed Output Ports
Data Clock Output Provided
Low Power: 570 mW Typical
Internal PLL Generates CLOCK from HSYNC
Serial Port Interface
Fully Programmable
Supports Alternate Pixel Sampling for HigherResolution Applications
APPLICATIONS
RGB Graphics Processing
LCD Monitors and Projectors
Plasma Display Panels
Scan Converters
100 MSPS/140 MSPS
Analog Flat Panel Interface
AD9884A
FUNCTIONAL BLOCK DIAGRAM
AD9884A
8
RIN
CLAMP
8
A/D
8
8
GIN
8
A/D
CLAMP
8
8
BIN
HSYNC
COAST
CLAMP
CKINV
CKEXT
CLAMP
8
A/D
8
2
ROUTA
ROUTB
GOUTA
GOUTB
BOUTA
BOUTB
DATACK
CLOCK
GENERATOR
HSOUT
0.15V
CONTROL
REF
REFIN
FILT SOGIN SOGOUT SDA SCL A0 A1 PWRDN REFOUT
GENERAL DESCRIPTION
The AD9884A is a complete 8-bit 140 MSPS monolithic analog
interface optimized for capturing RGB graphics signals from
personal computers and workstations. Its 140 MSPS encode
rate capability and full-power analog bandwidth of 500 MHz
supports display resolutions of up to 1280 × 1024 (SXGA) at
75 Hz with sufficient input bandwidth to accurately acquire and
digitize each pixel.
20 MHz to 140 MHz. PLL clock jitter is typically 400 ps p-p
relative to the input reference. When the COAST signal is presented, the PLL maintains its output frequency in the absence
of HSYNC. A 32-step sampling phase adjustment is provided.
Data, HSYNC and Data Clock output phase relationships are
always maintained. The PLL can be disabled and an external
clock input provided as the pixel clock.
To minimize system cost and power dissipation, the AD9884A
includes an internal +1.25 V reference, PLL to generate a pixel
clock from HSYNC, and programmable gain, offset and clamp
circuits. The user provides only a +3.3 V power supply, analog
input, and HSYNC signals. Three-state CMOS outputs may be
powered by a supply between 2.5 V and 3.3 V.
A clamp signal is generated internally or may be provided by the
user through the CLAMP input pin. This device is fully programmable via a two-wire serial port.
The AD9884A’s on-chip PLL generates a pixel clock from the
HSYNC input. Pixel clock output frequencies range from
Fabricated in an advanced CMOS process, the AD9884A is
provided in a space-saving 128-lead MQFP surface mount plastic package and is specified over a 0°C to +70°C temperature
range.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
(VD = +3.3 V, V DD = +3.3 V, PV D = +3.3 V, ADC Clock Frequency = Maximum, PLL
AD9884A–SPECIFICATIONS Clock Frequency = Maximum, Control Registers Programmed to Default State)
Parameter
Temp
Test
Level
AD9884AKS-100
Min
Typ
Max
RESOLUTION
DC ACCURACY
Differential Nonlinearity
8
± 0.5
+25°C
Full
+25°C
Full
Full
I
VI
I
VI
VI
Full
Full
+25°C
+25°C
Full
Full
Full
Full
VI
VI
V
I
VI
VI
VI
VI
Full
Full
VI
V
+1.20
VI
IV
IV
VI
VI
VI
VI
VI
VI
VI
VI
IV
VI
IV
IV
IV
IV
100
Sampling Phase Tempco
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
+25°C
Full
Full
DIGITAL INPUTS
Input Voltage, High (VIH)
Input Voltage, Low (VIL)
Input Current, High (IIH)
Input Current, Low (IIL)
Input Capacitance
Full
Full
Full
Full
+25°C
VI
VI
VI
VI
V
2.5
Full
Full
VI
VI
VDD – 0.1
Full
IV
45
Integral Nonlinearity
No Missing Codes
ANALOG INPUT
Input Voltage Range
Minimum
Maximum
Gain Tempco
Input Bias Current
Input Offset Voltage
Input Full-Scale Matching
Offset Adjustment Range
REFERENCE OUTPUT
Output Voltage
Temperature Coefficient
SWITCHING PERFORMANCE
Maximum Conversion Rate
Minimum Conversion Rate
Data to Clock Skew, tSKEW
tBUFF
tSTAH
tDHO
tDAL
tDAH
tDSU
tSTASU
tSTOSU
HSYNC Input Frequency
Maximum PLL Clock Rate
Minimum PLL Clock Rate
PLL Jitter
DIGITAL OUTPUTS
Output Voltage, High (VOH)
Output Voltage, Low (VOL)
Duty Cycle
DATACK, DATACK
Output Coding
AD9884AKS-140
Min
Typ
Max
± 0.5
8
± 1.0
± 1.0
± 1.25
± 1.75
± 0.5
± 0.8
Guaranteed
0.5
+1.15/–1.0
+1.25/–1.0
± 1.4
± 2.5
LSB
LSB
LSB
LSB
0.5
V p-p
V p-p
ppm/°C
µA
µA
mV
%FS
%FS
1.0
100
22
Bits
Guaranteed
1.0
7
1.5
23.5
+1.25
± 50
280
1
1
50
5.0
25
22
+1.30
+1.20
7
1.5
23.5
+1.25
± 50
1
1
50
5.0
25
+1.30
140
10
+2.0
–0.5
4.7
4.0
0
4.7
4.0
250
4.7
4.0
15
100
110
400
10
+2.0
–0.5
4.7
4.0
0
4.7
4.0
250
4.7
4.0
15
140
20
7001
10001
110
475
15
20
7502
10002
15
2.5
0.8
–1.0
1.0
0.8
–1.0
1.0
3
3
VDD – 0.1
0.1
50
Binary
–2–
Unit
55
45
50
Binary
V
ppm/°C
MSPS
MSPS
ns
µs
µs
µs
µs
µs
ns
µs
µs
kHz
MHz
MHz
ps p-p
ps p-p
ps/°C
V
V
µA
µA
pF
0.1
V
V
55
%
REV. B
AD9884A
Parameter
Temp
Test
Level
AD9884AKS-100
Min
Typ
Max
AD9884AKS-140
Min
Typ
Max
POWER SUPPLY
VD Supply Voltage
VDD Supply Voltage
PVD Supply Voltage
ID Supply Current (VD)
IDD Supply Current (VDD)3
IPVD Supply Current (PVD)
Total Power Dissipation
Power-Down Supply Current
Power-Down Dissipation
Full
Full
Full
+25°C
+25°C
+25°C
Full
Full
Full
IV
IV
IV
V
V
V
VI
VI
VI
3.0
2.2
3.0
3.0
2.2
3.0
+25°C
+25°C
+25°C
+25°C
Full
V
V
V
I
V
Full
V
DYNAMIC PERFORMANCE
Analog Bandwidth, Full Power
Transient Response
Overvoltage Recovery Time
Signal-to-Noise Ratio (SNR)4
(Without Harmonics)
fIN = 40.7 MHz
Crosstalk
THERMAL CHARACTERISTICS
θJC–Junction-to-Case
Thermal Resistance
θJA–Junction-to-Ambient
Thermal Resistance
3.3
3.3
3.3
125
33
15
570
2.0
6.6
3.6
3.6
3.6
675
25
82.5
3.6
3.6
3.6
775
25
82.5
V
V
V
mA
mA
mA
mW
mA
mW
500
2
1.5
46.2
45.0
MHz
ns
ns
dB
dB
60
60
dBc
V
8.4
8.4
°C/W
V
35
35
°C/W
44.0
500
2
1.5
46.5
46.0
3.3
3.3
3.3
135
47
15
650
2.0
6.6
Unit
43.5
NOTES
1
VCORNGE = 01, CURRENT = 001, PLLDIV = 1693 10 .
2
VCORNGE = 10, CURRENT = 110, PLLDIV = 1600 10 .
3
DEMUX = 1; DATACK and DATACK load = 15 pF; Data load = 5 pF.
4
Using external pixel clock.
Specifications subject to change without notice.
ORDERING GUIDE
Model
Temperature Package
Range
Description
ABSOLUTE MAXIMUM RATINGS *
VD, PVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +4 V
PVD to VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.5 V
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +4 V
Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . VD to –0.5 V
REFIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VD to 0.0 V
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . VD to 0.0 V
Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
Operating Temperature . . . . . . . . . . . . . . . . . –20°C to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . +175°C
Maximum Case Temperature . . . . . . . . . . . . . . . . . . +150°C
Package
Option
AD9884AKS-140 0°C to +70°C MQFP
S-128
AD9884AKS-100 0°C to +70°C MQFP
S-128
AD9884A/PCB
+25°C
Evaluation Board
EXPLANATION OF TEST LEVELS
Test Level
I. 100% production tested.
II. 100% production tested at +25°C and sample tested at specified
temperatures.
III. Sample tested only.
IV. Parameter is guaranteed by design and characterization testing.
V. Parameter is a typical value only.
VI. 100% production tested at +25°C; guaranteed by design and
characterization testing.
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions outside of those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum ratings
for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD9884A features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. B
–3–
WARNING!
ESD SENSITIVE DEVICE
AD9884A
Table I. Package Interconnections
Signal Type
Name
Function
Value
Package Pin
Inputs
RAIN
GAIN
BAIN
Analog Input for RED Channel
Analog Input for GREEN Channel
Analog Input for BLUE Channel
0.5 V to 1.0 V FS
0.5 V to 1.0 V FS
0.5 V to 1.0 V FS
7
15
22
HSYNC
COAST
CLAMP
SOGIN
Horizontal Sync Input
Clock Generator Coast Input (Optional)
External Clamp Input (Optional)
Sync On Green Slicer Input (Optional)
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
0.5 V to 1.0 V FS
40
41
28
14
CKEXT
CKINV
External Clock Input (Optional)
Sampling Clock Inversion (Optional)
3.3 V CMOS
3.3 V CMOS
44
27
DRA7-0
DRB7-0
DGA7-0
DGB7-0
DBA7-0
DBB 7-0
Data Output, Red Channel, Port A
Data Output, Red Channel, Port B
Data Output, Green Channel, Port A
Data Output, Green Channel, Port B
Data Output, Blue Channel, Port A
Data Output, Blue Channel, Port B
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
105–112
95–102
85–92
75–82
65–72
55–62
DATACK
DATACK
Data Output Clock
Data Output Clock Complement
3.3 V CMOS
3.3 V CMOS
115
116
HSOUT
SOGOUT
Horizontal Sync Output
Sync On Green Slicer Output
3.3 V CMOS
3.3 V CMOS
117
118
SDA
SCL
A0, A 1
Serial Data I/O
Serial Interface Clock
Serial Port Address LSBs
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
29
30
31, 32
PWRDN
Power-Down Control Input
3.3 V CMOS
125
Analog Interface
REFOUT
REFIN
FILT
Internal Reference Output
Reference Input
External Filter Connection
+1.25 V
+1.25 V ± 10%
126
127
45
Power Supply
VD
Main Power Supply
3.3 V ± 10%
VDD
PVD
GND
Digital Output Power Supply
Clock Generator Power Supply
Ground
Outputs
Control
No Connect
4, 8, 10, 11, 16, 18, 19, 23, 25,
124, 128
2.5 V to 3.3 V ± 10% 54, 64, 74, 84, 94, 104, 114, 120
3.3 V ± 10%
33, 34, 43, 48, 50
0V
5, 6, 9, 12, 13, 17, 20, 21, 24, 26,
35, 39, 42, 47, 49, 51, 52, 53, 63,
73, 83, 93, 103, 113, 119, 121,
122, 123
NC
1–3, 36–38, 46
–4–
REV. B
AD9884A
1
NC
2
NC
3
VD
104 VDD
103 GND
106 DRA6
105 DRA7
107 DRA5
109 DRA3
108 DRA4
111 DRA1
110 DRA2
112 DRA0
114 VDD
113 GND
116 DATACK
115 DATACK
117 HSOUT
119 GND
102 DRB0
PIN 1
IDENTIFIER
101 DRB1
4
100 DRB2
99 DRB3
GND
5
98 DRB4
GND
6
97 DRB5
RAIN
7
96 DRB6
VD
8
95 DRB7
GND
9
94 VDD
VD 10
93 GND
VD 11
92 DGA0
GND 12
91 DGA1
GND 13
90 DGA2
SOGIN 14
89 DGA3
GAIN 15
88 DGA4
VD 16
87 DGA5
GND 17
86 DGA6
VD 18
VD 19
GND 20
GND 21
REV. B
118 SOGOUT
121 GND
120 VDD
122 GND
124 VD
123 GND
126 REFOUT
125 PWRDN
128 VD
NC
127 REFIN
PIN CONFIGURATION
AD9884A
85 DGA7
TOP VIEW
PINS DOWN
(Not to Scale)
83 GND
84 VDD
82 DGB0
BAIN 22
81 DGB1
VD 23
GND 24
79 DGB3
VD 25
GND 26
77 DGB5
CKINV 27
76 DGB6
CLAMP 28
75 DGB7
80 DGB2
78 DGB4
SDA 29
74 VDD
SCL 30
A0 31
73 GND
72 DBA0
A1 32
71 DBA1
PVD 33
PVD 34
70 DBA2
GND 35
NC 36
68 DBA4
69 DBA3
67 DBA5
–5–
58
60
61
62
63
64
DBB2
DBB1
DBB0
GND
VDD
57
DBB5
59
56
DBB3
55
DBB7
DBB6
NC = NO CONNECT
DBB4
53
54
VDD
52
GND
GND
51
50
PVD
GND
48
49
GND
PVD
47
NC
GND
45
46
FILT
43
44
PVD
41
42
GND
CKEXT
39
40
65 DBA7
GND
66 DBA6
NC 38
HSYNC
COAST
NC 37
AD9884A
PIN FUNCTION DESCRIPTIONS
Pin Name
Function
INPUTS
RAIN
GAIN
BAIN
Analog Input for RED Channel
Analog Input for GREEN Channel
Analog Input for BLUE Channel
High impedance inputs that accepts the RED, GREEN, and BLUE channel graphics signals, respectively. The
three channels are identical, and can be used for any colors, but colors are assigned for convenient reference. They
accommodate input signals ranging from 0.5 V to 1.0 V full scale. Signals should be ac-coupled to these pins to
support clamp operation.
HSYNC
Horizontal Sync Input
This input receives a logic signal that establishes the horizontal timing reference and provides the frequency reference for pixel clock generation. The logic sense of this pin is controlled by HSPOL. Only the leading edge of
HSYNC is active. When HSPOL = 0, the falling edge of HSYNC is used. When HSPOL = 1, the rising edge is
active. The input includes a Schmitt trigger for noise immunity, with a nominal input threshold of 1.5 V.
Electrostatic Discharge (ESD) protection diodes will conduct heavily if this pin is driven more than 0.5 V above
the 3.3 V power supply (or more than 0.5 V below ground). If a 5 V signal source is driving this pin, the signal
should be clamped or current limited.
COAST
Clock Generator Coast Input (optional)
This input may be used to cause the pixel clock generator to stop synchronizing with HSYNC and continue producing a clock at its present frequency and phase. This is useful when processing sources that fail to produce horizontal sync pulses when in the vertical interval. The COAST signal is generally NOT required for PC-generated
signals. The logic sense of this pin is controlled by CSTPOL. COAST may be asserted at any time. When not
used, this pin must be grounded and CSTPOL programmed to 1. CSTPOL defaults to 1 at power-up.
CLAMP
External Clamp Input (optional)
This logic input may be used to define the time during which the input signal is clamped to ground, establishing a
black reference. It should be exercised when a black signal is known to be present on the analog input channels,
typically during the back porch period of the graphics signal. The CLAMP pin is enabled by setting control bit
EXTCLMP to 1 (default power-up is 0). When disabled, this pin is ignored and the clamp timing is determined
internally by counting a delay and duration from the trailing edge of the HSYNC input. The logic sense of this pin
is controlled by CLAMPOL. When not used, this pin must be grounded and EXTCLMP programmed to 0.
SOGIN
Sync On Green Slicer Input (optional)
This input is provided to assist in processing signals with embedded sync, typically on the GREEN channel. The
pin is connected to a high speed comparator with an internally-generated threshold of 0.15 V. When connected to
a dc-coupled graphics signal with embedded sync, it will produce a noninverting digital output on SOGOUT that
changes state whenever the input signal crosses 0.15 V. This is usually a composite sync signal, containing both
vertical and horizontal sync information that must be separated before passing the horizontal sync signal to HSYNC.
The SOG slicer comparator continues to operate when the AD9884A is put into a power-down state. When not
used, this input should be grounded.
CKEXT
External Clock Input (optional)
This pin may be used to provide an external clock to the AD9884A, in place of the clock internally-generated from
HSYNC. This input is enabled by programming EXTCLK to 1. When an external clock is used, all other internal
functions operate normally. When unused, this pin should be tied through a 10 kΩ resistor to GROUND, and
EXTCLK programmed to 0. The clock phase adjustment still operates when an external clock source is used.
CKINV
Sampling Clock Inversion (optional)
This pin may be used to invert the pixel sampling clock, which has the effect of shifting the sampling phase
180 degrees. This is in support of Alternate Pixel Sampling mode, wherein higher frequency input signals (up to
280 Mpps) may be captured by first sampling the odd pixels, then capturing the even pixels on the subsequent
frame. This pin should be exercised only during blanking intervals (typically vertical blanking) as it may produce
several samples of corrupted data during the phase shift. CKINV should be grounded when not used.
–6–
REV. B
AD9884A
PIN FUNCTION DESCRIPTIONS (Continued)
Pin Name
Function
OUTPUTS
DRA7–0
DRB7–0
DGA7–0
DGB7–0
DBA7–0
DBB 7–0
Data Output, Red Channel, Port A
Data Output, Red Channel, Port B
Data Output, Green Channel, Port A
Data Output, Green Channel, Port B
Data Output, Blue Channel, Port A
Data Output, Blue Channel, Port B
The main data outputs. Bit 7 is the MSB. Each channel has two ports. When the part is operated in Single Channel mode (DEMUX = 0), all data are presented to Port A, and Port B is placed in a high impedance state. Programming DEMUX to 1 establishes Dual Channel mode, wherein alternate pixels are presented to Port A and
Port B of each channel. These will appear simultaneously, two pixels presented at the time of every second input
pixel, when PAR is set to 1 (parallel mode). When PAR = 0, pixel data appear alternately on the two ports, one
new sample with each incoming pixel (interleaved mode). In Dual Channel mode, the first pixel sampled after
HSYNC is routed to Port A. The second pixel goes to Port B, the third to A, etc. The delay from pixel sampling
time to output is fixed. When the sampling time is changed by adjusting the PHASE register, the output timing is
shifted as well. The DATACK, DATACK and HSOUT outputs are also moved, so the timing relationship among
the signals is maintained.
DATACK
DATACK
Data Output Clock
Data Output Clock Complement
Differential data clock output signals to be used to strobe the output data and HSOUT into external logic. They
are produced by the internal clock generator and are synchronous with the internal pixel sampling clock. When the
AD9884A is operated in Single Channel mode, the output frequency is equal to the pixel sampling frequency.
When operating in Dual Channel mode, the Data Output Clock and the Output Data are presented at one-half the
pixel rate. When the sampling time is changed by adjusting the PHASE register, the output timing is shifted as
well. The Data, DATACK, DATACK and HSOUT outputs are all moved, so the timing relationship among the
signals is maintained. Either or both signals may be used, depending on the timing mode and interface design
employed.
HSOUT
Horizontal Sync Output
A reconstructed and phase-aligned version of the HSYNC input. This signal is always active HIGH. By maintaining alignment with DATACK, DATACK, and Data, data timing with respect to horizontal sync can always be
clearly determined.
SOGOUT
Sync On Green Slicer Output
The output of the Sync On Green slicer comparator. When SOGIN is presented with a dc-coupled ground-referenced
analog graphics signal containing composite sync, SOGOUT will produce a digital composite sync signal. This
signal gets no other processing on the AD9884A. The SOG slicer comparator continues to operate when the
AD9884A is put into a power-down state.
CONTROL
SDA
Serial Data I/O
Bidirectional data port for the serial interface port.
SCL
Serial Interface Clock
Clock input for the serial interface port.
A1–0
Serial Port Address LSBs
The two least significant bits of the serial port address are set by the logic levels on these pins. Connect a pin to
ground to set the address bit to 0. Tie it HIGH (to VD through 10 kΩ) to set the address bit to 1. Using these pins,
the serial address may be set to any value from 98h to 9Fh. Up to four AD9884As may be used on the same serial
bus by appropriately setting these bits. They can also be used to change the AD9884A address if a conflict is found
with another device on the bus.
PWRDN
Power-Down Control Input
Bringing this pin LOW puts the AD9884A into a very low power dissipation mode. The output buffers are placed
in a high impedance state. The clock generator is stopped. The control register contents are maintained. The Sync
On Green Slicer (SOGOUT) and internal reference continue to function.
REV. B
–7–
AD9884A
PIN FUNCTION DESCRIPTIONS (Continued)
Pin Name
Function
ANALOG INTERFACE
REFOUT
Internal Reference Output
Output from the internal 1.25 V bandgap reference. This output is intended to drive relatively light loads. It can
drive the AD9884A Reference input directly, but should be externally buffered if it is used to drive other loads as
well. The absolute accuracy of this output is ± 4%, and the temperature coefficient is ± 50 ppm, which is adequate
for most AD9884A applications. If higher accuracy is required, an external reference may be employed. If an external reference is used, tie this pin to ground through a 0.1 µF capacitor.
REFIN
Reference Input
The reference input accepts the master reference voltage for all AD9884A internal circuitry (+1.25 V ± 10%). It
may be driven directly by the REFOUT pin. Its high impedance presents a very light load to the reference source.
This pin should be bypassed to Ground with a 0.1 µF capacitor.
FILT
External Filter Connection
For proper operation, the pixel clock generator PLL requires an external filter. Connect the filter shown in Figure
10 to this pin. For optimal performance, minimize noise and parasitics on this node.
POWER SUPPLY
VD
Main Power Supply
These pins supply power to the main elements of the circuit. It should be as quiet and filtered as possible.
VDD
Digital Output Power Supply
A large number of output pins (up to 52) switching at high speed (up to 140 MHz) generates a lot of power supply
transients (noise). These supply pins are identified separately from the VD pins so special care can be taken to
minimize output noise transferred into the sensitive analog circuitry. If the AD9884A is interfacing with lowervoltage logic, VDD may be connected to a lower supply voltage (as low as 2.5 V) for compatibility.
PVD
Clock Generator Power Supply
The most sensitive portion of the AD9884A is the clock generation circuitry. These pins provide power to the
clock PLL and help the user design for optimal performance. The designer should provide “quiet,” noise-free
power to these pins.
GND
Ground
The ground return for all circuitry on chip. It is recommended that the AD9884A be assembled on a single solid
ground plane, with careful attention to ground current paths. See the Design Guide for details.
–8–
REV. B
AD9884A
CONTROL REGISTER MAP
Table III. Default Register Values
The AD9884A is initialized and controlled by a set of registers
that determine the operating modes. An external controller is
employed to write and read the control registers through the
2-line serial interface port.
Table II. Control Register Map
Reg Bit Default
Mnemonic
Function
Reg
Value
00
01
02
03
04
05
06
07
01101001
1101 0000
10000000
10000000
10000000
100000 00
100000 00
100000 00
69h
D0h
80h
80h
80h
80h
80h
80h
Reg
Value
08
09
0A
0B
0C
0D
0E
0F
10000000
10000000
11110100
10000 000
0 01 001 00
00000000
0000xxx0
00000000
80h
80h
F4h
80h
24h
00h
0xh
00h
PLL Divider Control
00 7–0 01101001 PLLDIVM
01 7–4 1101•••• PLLDIVL
01 3–0 ••••0000
PLL Divide Ratio MSBs
PLL Divide Ratio LSBs
Reserved, Set to Zero
Input Gain
02 7–0 10000000 REDGAIN
03 7–0 10000000 GRNGAIN
04 7–0 10000000 BLUGAIN
Red Channel Gain Adjust
Green Channel Gain Adjust
Blue Channel Gain Adjust
Input Offset
05 7–2 100000•• REDOFST
05 1–0 ••••••00
06 7–2 100000•• GRNOFST
06 1–0 ••••••00
07 7–2 100000•• BLUOFST
07 1–0 ••••••00
Red Channel Offset Adjust
Reserved, Set to Zero
Green Channel Offset Adjust
Reserved, Set to Zero
Blue Channel Offset Adjust
Reserved, Set to Zero
The PLL derives a master clock from an incoming HSYNC
signal. The master clock frequency is then divided by an integer
value, and the divider’s output is phase-locked to HSYNC. This
PLLDIV value determines the number of pixel times (pixels
plus horizontal blanking overhead) per line. This is typically
20% to 30% more than the number of active pixels in the display.
Clamp Timing
08 7–0 10000000 CLPLACE
09 7–0 10000000 CLDUR
Clamp Placement
Clamp Duration
General Control 1
0A 7
1•••••••
0A 6
•1••••••
••1•••••
0A 5
0A 4
•••1••••
0A 3
••••0•••
0A 2
•••••1••
0A 1
••••••0•
0A 0
•••••••0
The 12-bit value of PLLDIV supports divide ratios from 2 to
4095. The higher the value loaded in this register, the higher
the resulting clock frequency with respect to a fixed HSYNC
frequency.
Output Port Select
Output Timing Select
HSYNC Polarity
COAST Polarity
Clamp Signal Source
Clamp Signal Polarity
External Clock Select
Reserved, Set to Zero
DEMUX
PAR
HSPOL
CSTPOL
EXTCLMP
CLAMPOL
EXTCLK
Clock Generator Control
0B 7–3 10000••• PHASE
0B 2–0 •••••000
0C 7
0•••••••
0C 6–5 •01••••• VCORNGE
0C 4–2 •••001•• CURRENT
0C 1–0 ••••••00
CONTROL REGISTER DETAIL
PLL DIVIDER CONTROL
00
PLLDIVM
PLL Divide Ratio MSBs
The eight most significant bits of the 12-bit PLL divide ratio
PLLDIV. The operational divide ratio is PLLDIV + 1.
VESA has established some standard timing specifications,
which will assist in determining the value for PLLDIV as a
function of horizontal and vertical display resolution and frame
rate (Table VII). However, many computer systems do not
conform precisely to the recommendations, and these numbers
should be used only as a guide. The display system manufacturer should provide automatic or manual means for optimizing
PLLDIV. An incorrectly set PLLDIV will usually produce one
or more vertical noise bars on the display. The greater the error,
the greater the number of bars produced.
Clock Phase Adjust
Reserved, Set to Zero
Reserved, Set to Zero
VCO Range Select
Charge Pump Current
Reserved, Set to Zero
The power-up default value of PLLDIV is 1693 (PLLDIVM =
69h, PLLDIVL = Dxh).
01
7–4
PLLDIVL
PLL Divide Ratio LSBs
The four least significant bits of the 12-bit PLL divide ratio
PLLDIV. The operational divide ratio is PLLDIV + 1.
General Control 2
0D 7–5 000•••••
Reserved, Set to Zero
0D 4
•••0•••• OUTPHASE Output Port Phase
Die Revision ID
0D 3–1 ••••000• REVID
Reserved, Set to Zero
0D 0
•••••••0
0E 7–0 00000000
Reserved, Set to Zero
REV. B
7–0
The power-up default value of PLLDIV is 1693 (PLLDIVM =
69h, PLLDIVL = Dxh).
–9–
AD9884A
INPUT GAIN
02
CLAMP TIMING
7–0
REDGAIN
08
Red Channel Gain Adjust
GRNGAIN
Clamp Placement
When EXTCLMP = 0, a clamp signal is generated internally, at
a position established by CLPLACE and for a duration set by
CLDUR. Clamping is started CLPLACE pixel periods after the
trailing edge of HSYNC. CLPLACE may be programmed to
any value between 1 and 255. CLPLACE = 0 is not supported.
The clamp should be placed during a time that the input signal
presents a stable black-level reference, usually the back porch
period between HSYNC and the image. A value of 08h will
usually work.
The power-up default value is REDGAIN = 80h.
7–0
CLPLACE
An 8-bit register that sets the position of the internally generated
clamp.
An 8-bit word that sets the gain of the RED channel. The
AD9884A can accommodate input signals with a full-scale
range of between 0.5 V and 1.0 V p-p. Setting REDGAIN to
255 corresponds to an input range of 1.0 V. A REDGAIN of
0 establishes an input range of 0.5 V. Note that increasing
REDGAIN results in the picture having less contrast (the
input signal uses fewer of the available converter codes). See
Figure 8.
03
7–0
Green Channel Gain Adjust
An 8-bit word that sets the gain of the GREEN channel. See
REDGAIN (02).
When EXTCLMP = 1, this register is ignored.
The power-up default value is CLPLACE = 80h.
The power-up default value is GRNGAIN = 80h.
09
04
7–0
BLUGAIN
INPUT OFFSET
REDOFST
Clamp Duration
When EXTCLMP = 0, a clamp signal is generated internally, at
a position established by CLPLACE and for a duration set by
CLDUR. Clamping is started CLPLACE pixel periods after the
trailing edge of HSYNC, and continues for CLDUR pixel periods. CLDUR may be programmed to any value between 1 and
255. CLDUR = 0 is not supported.
The power-up default value is BLUGAIN = 80h.
7–2
CLDUR
An 8-bit register that sets the duration of the internally generated clamp.
An 8-bit word that sets the gain of the BLUE channel. See
REDGAIN (02).
05
7–0
Blue Channel Gain Adjust
Red Channel Offset Adjust
A six-bit offset binary word that sets the dc offset of the RED
channel.
One LSB of offset adjustment equals approximately one LSB
change in the ADC offset. Therefore, the absolute magnitude of
the offset adjustment scales as the gain of the channel is changed
(Figure 9). A nominal setting of 31 results in the channel nominally clamping the back porch (during the clamping interval) to
code 00. An offset setting of 63 results in the channel clamping
to code 31 of the ADC. An offset setting of 0 clamps to code
–31 (off the bottom of the range). Increasing the value of
REDOFST decreases the brightness of the channel.
For the best results, the clamp duration should be set to include
the majority of the black reference signal time found following
the HSYNC signal trailing edge. Insufficient clamping time can
produce brightness changes at the top of the screen, and a slow
recovery from large changes in the Average Picture Level (APL),
or brightness. A value of 10h to 20h works with most standard
signals.
When EXTCLMP = 1, this register is ignored.
The power-up default value is CLDUR = 80h.
The power-up default value is REDOFST = 80h.
06
7–2
GRNOFST
Green Channel Offset Adjust
A six-bit offset binary word that sets the dc offset of the GREEN
channel. See REDOFST (05).
The power-up default value is GRNOFST = 80h.
07
7–2
BLUOFST
Blue Channel Offset Adjust
A six-bit offset binary word that sets the DC offset of the GREEN
channel. See REDOFST (05).
The power-up default value is BLUOFST = 80h.
–10–
REV. B
AD9884A
GENERAL CONTROL
0A
7
DEMUX
Output Port Select
A bit that determines whether all pixels are presented to a single
port (A), or alternating pixels are demultiplexed to Ports A and B.
DEMUX
Function
0
1
All Data Goes to Port A
Alternate Pixels Go to Port A and Port B
CSTPOL
Function
0
1
Active LOW
Active HIGH
Active LOW means that the clock generator will ignore HSYNC
inputs when COAST is LOW, and continue operating at the
same nominal frequency until COAST goes HIGH.
Active HIGH means that the clock generator will ignore HSYNC
inputs when COAST is HIGH, and continue operating at the
same nominal frequency until COAST goes LOW.
When DEMUX = 0, Port B outputs are in a high impedance
state.
The power-up default value is CSTPOL = 1.
The power-up default value is DEMUX = 1.
0A
6
PARALLEL
0A
Output Timing Select
3
EXTCLMP
Clamp Signal Source
A bit that determines the source of clamp timing.
Setting this bit to a Logic 1 delays data on Port A and the
DATACK output by one-half DATACK period so that the
rising edge of DATACK may be used to externally latch data
from both Port A and Port B. When this bit is set to a Logic 0,
the rising edge of DATACK may be used to externally latch
data from Port A only, and the DATACK rising edge may be
used to externally latch data from Port B.
EXTCLMP
Function
0
1
Internally-generated clamp
Externally-provided clamp signal
PARALLEL
Function
0
1
Data Alternates Between Ports
Simultaneous Data on Alternate DATACKs
A 1 enables the external CLAMP input pin. The three channels
are clamped when the CLAMP signal is active. The polarity of
CLAMP is determined by the CLAMPOL bit.
A 0 enables the clamp timing circuitry controlled by CLPLACE
and CLDUR. The clamp position and duration is counted from
the trailing edge of HSYNC.
The power-up default value is EXTCLMP = 0.
When in single port mode (DEMUX = 0), this bit is ignored.
0A
The power-up default value is PARALLEL = 1.
0A
5
HSPOL
2
CLAMPOL
A bit that determines the polarity of the externally provided
CLAMP signal.
HSYNC Polarity
A bit that must be set to indicate the polarity of the HSYNC
signal that is applied to the HSYNC input.
CLAMPOL
Function
HSPOL
Function
0
1
Active LOW
Active HIGH
0
1
Active LOW
Active HIGH
A 0 means that the circuit will clamp when CLAMP is LOW,
and it will pass the signal to the ADC when CLAMP is HIGH.
Active LOW is the traditional negative-going HSYNC pulse.
Sampling timing is based on the leading edge of HSYNC, which
is the FALLING edge. The Clamp Position, as determined by
CLPLACE, is measured from the trailing edge.
Active HIGH is inverted from the traditional HSYNC, with a
positive-going pulse. This means that sampling timing will be
based on the leading edge of HSYNC, which is now the RISING edge, and clamp placement will count from the FALLING
edge.
The device will operate more-or-less properly if this bit is set
incorrectly, but the internally generated clamp position, as established by CLPOS, will not be placed as expected, which may
generate clamping errors.
The power-up default value is HSPOL = 1.
0A
4
CSTPOL
COAST Polarity
A bit that must be set to indicate the polarity of the COAST
signal that is applied to the COAST input.
REV. B
Clamp Signal Polarity
A 1 means that the circuit will clamp when CLAMP is HIGH,
and it will pass the signal to the ADC when CLAMP is LOW.
The power-up default value is CLAMPOL = 1.
0A
1
EXTCLK
External Clock Select
A bit that determines the source of the pixel clock.
EXTCLK
Function
0
1
Internally generated clock
Externally provided clock signal
A 0 enables the internal PLL that generates the pixel clock from
an externally-provided HSYNC.
A 1 enables the external CKEXT input pin. In this mode, the
PLL Divide Ratio (PLLDIV) is ignored. The clock phase adjust
(PHASE) is still functional.
The power-up default value is EXTCLK = 0.
–11–
AD9884A
CLOCK GENERATOR CONTROL
0B
7–3
PHASE
0D
Clock Phase Adjust
A five-bit value that adjusts the sampling phase in 32 steps across
one pixel time. Each step represents an 11.25 degree shift in
sampling phase.
The power-up default value is PHASE = 16.
0C
6–5
VCORNGE
VCO Range Select
Two bits that establish the operating range of the clock generator.
VCORNGE
Range (MHz)
00
01
10
11
20-60
50-90
80-120
110-140
The power-up default value is VCORNGE = 01.
4–2
CURRENT
Charge Pump Current
Three bits that establish the current driving the loop filter in the
clock generator.
CURRENT
Current (␮A)
000
001
010
011
100
101
110
111
50
100
150
250
350
500
750
1500
The power-up default value is CURRENT = 001.
4
OUTPHASE
The die revision of the AD9884A can be determined by reading
these three bits.
Serial Control Port
A 2-wire serial control interface is provided. Up to four AD9884A
devices may be connected to the 2-wire serial interface, with
each device having a unique address.
The 2-wire interface comprises a clock (SCL) and a bidirectional data (SDA) pin. The Analog Flat Panel Interface acts as a
slave for receiving and transmitting data over the serial interface.
When the serial interface is not active, the logic levels on SCL
and SDA are pulled HIGH by external pull-up resistors.
There are six components to serial bus operation:
• Start Signal
• Slave Address Byte
• Base Register Address Byte
• Data Byte to Read or Write
• Stop Signal
When the serial interface is inactive (SCL and SDA are HIGH)
communications are initiated by sending a start signal. The start
signal is a HIGH-to-LOW transition on SDA while SCL is
HIGH. This signal alerts all slaved devices that a data transfer
sequence is coming.
Table IV. Serial Port Addresses
Output Port Phase
One bit that determines whether even pixels or odd pixels go to
Port A.
OUTPHASE
First Pixel After HSYNC
0
1
Port A
Port B
Silicon Revision ID
The first eight bits of data transferred after a start signal comprising a seven bit slave address (the first seven bits) and a
single R/W bit (the eighth bit). The R/W bit indicates the direction of data transfer, read from (1) or write to (0) the slave
device. If the transmitted slave address matches the address of
the device (set by the state of the SA1-0 input pins in Table IV),
the AD9884A acknowledges by bringing SDA LOW on the
ninth SCL pulse. If the addresses do not match, the AD9884A
does not acknowledge.
CURRENT must be set to correspond with the desired operating frequency (incoming pixel rate).
0D
REVID
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA
must change only when SCL is LOW. If SDA changes state
while SCL is HIGH, the serial interface interprets that action as
a start or stop sequence.
VCORNGE must be set to correspond with the desired operating frequency (incoming pixel rate).
0C
3–1
In normal operation (OUTPHASE = 0), when operating in
Dual Channel output mode (DEMUX = 1), the first sample
after the HSYNC leading edge is presented at Port A. Every
subsequent ODD sample appears at Port A. All EVEN samples
go to Port B.
Bit 7
Bit 6
A5
A6
(MSB)
Bit 5
A4
Bit 4
A3
Bit 3
A2
Bit 2
A1
Bit 1 Bit 0
A0
R/W
(LSB)
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
0
1
0
1
0
0
0
0
Data Transfer via Serial Interface
For each byte of data read or written, the MSB is the first bit of
the sequence.
When OUTPHASE = 1, these ports are reversed and the first
sample goes to Port B.
When DEMUX = 0, this bit is ignored.
When reading back the value of OUTPHASE, the bit appears at
register 0D, Bit 7.
If the AD9884A does not acknowledge the master device during
a write sequence, the SDA remains HIGH so the master can
generate a stop signal. If the master device does not acknowledge the AD9884A during a read sequence, the AD9884A interprets this as “end of data.” The SDA remains HIGH so the
master can generate a stop signal.
–12–
REV. B
AD9884A
Writing data to specific control registers of the AD9884A requires
that the 8-bit address of the control register of interest be written
after the slave address has been established. This control register
address is the base address for subsequent write operations. The
base address autoincrements by one for each byte of data written
after the data byte intended for the base address. If more bytes
are transferred than there are available addresses, the address
will not increment and remain at its maximum value of 0Eh. Any
base address higher than 0Eh will not produce an ACKnowledge
signal.
Data are read from the control registers of the AD9884A in a
similar manner. Reading requires two data transfer operations:
The base address must be written with the R/W bit of the slave
address byte LOW to set up a sequential read operation.
Reading (the R/W bit of the slave address byte HIGH) begins at
the previously established base address. The address of the read
register autoincrements after each byte is transferred.
To terminate a read/write sequence to the AD9884A, a stop
signal must be sent. A stop signal comprises a LOW-to-HIGH
transition of SDA while SCL is HIGH.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generating a stop signal to terminate the current communication. This is
used to change the mode of communication (read, write) between
the slave and master without releasing the serial interface lines.
Serial Interface Read/Write Examples
Write to One Control Register
•
•
•
•
•
Write to Four Consecutive Control Registers
•
•
•
•
•
•
•
•
Start Signal
Slave Address Byte (R/W Bit = LOW)
Base Address Byte
Data Byte to Base Address
Data Byte to (Base Address + 1)
Data Byte to (Base Address + 2)
Data Byte to (Base Address + 3)
Stop Signal
Read from One Control Register
•
•
•
•
•
•
•
Start Signal
Slave Address Byte (R/W Bit = LOW)
Base Address Byte
Start Signal
Slave Address Byte (R/W Bit = HIGH)
Data Byte from Base Address
Stop Signal
Read from Four Consecutive Control Registers
•
•
•
•
•
•
•
•
•
•
Start Signal
Slave Address Byte (R/W Bit = LOW)
Base Address Byte
Start Signal
Slave Address Byte (R/W Bit = HIGH)
Data Byte from Base Address
Data Byte from (Base Address + 1)
Data Byte from (Base Address + 2)
Data Byte from (Base Address + 3)
Stop Signal
Start Signal
Slave Address Byte (R/W Bit = LOW)
Base Address Byte
Data Byte to Base Address
Stop Signal
SDA
t BUFF
t STAH
t DSU
t DHO
t STASU
t STOSU
t DAL
SCL
t DAH
Figure 1. Serial Port Read/Write Timing
SDA
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
SCL
Figure 2. Serial Interface—Typical Byte Transfer
REV. B
–13–
BIT 0
ACK
AD9884A
The AD9884A includes all necessary input buffering, signal dc
restoration (clamping), offset and gain (brightness and contrast)
adjustment, pixel clock generation, sampling phase control, and
output data formatting. All controls are programmable via a
2-wire serial interface. Full integration of these sensitive analog
functions makes system design straightforward and less sensitive
to the physical and electrical environment.
800
mW
700
600
With a typical power dissipation of only 570 mW and an operating temperature range of 0°C to 70°C, the device requires no
special environmental considerations.
500
400
INPUT SIGNAL HANDLING
Analog Inputs
0
20
40
100
60
80
FREQUENCY – Mpps
120
140
160
Figure 3. Power Dissipation vs. Frequency
DESIGN GUIDE
GENERAL DESCRIPTION
The AD9884A is a fully-integrated solution for capturing analog
RGB signals and digitizing them for display on flat panel monitors or projectors. The circuit is also ideal for providing a computer interface for HDTV monitors or as the front-end to high
performance video scan converters.
Implemented in a high performance CMOS process, the interface can capture signals with pixel rates of up to 140 MegaPixels
Per Second (Mpps), and with an Alternate Pixel Sampling mode,
up to 280 Mpps.
VD
RIN
BIN
GIN
355V
Figure 4. Equivalent Analog Input Circuit
VD
DIGITAL
INPUT
The AD9884A has three high impedance analog input pins for
the red, green, and blue channels. They will accommodate
signals ranging from 0.5 V to 1.0 V p-p.
Signals are typically brought onto the interface board via a 15pin D connector, a VESA P&D connector, a DDWG DVI
connector, or via BNC connectors. The AD9884A should be
located as close as practical to the input connector. Signals
should be routed via matched- impedance traces (normally
75 Ω) to the IC input pins.
At that point the signal should be resistively terminated (75 Ω
to the signal ground return) and capacitively coupled to the
AD9884A inputs through 47 nF capacitors. These capacitors
form part of the dc restoration circuit.
In an ideal world of perfectly matched impedances, the best
performance can be obtained with the widest possible signal
bandwidth. The ultrawide bandwidth inputs of the AD9884A
(500 MHz) can track the input signal continuously as it moves
from one pixel level to the next, and digitize the pixel during a
long, flat pixel time. In many systems, however, there are mismatches, reflections, and noise, which can result in excessive
ringing and distortion of the input waveform. This makes it
more difficult to establish a sampling phase that provides good
image quality. It has been shown that a small inductor in series
with the input is effective in rolling off the input bandwidth
slightly, and providing a high quality signal over a wider range of
conditions. Using a Fair-Rite #2508051217Z0 High-Speed
Signal Chip Bead inductor in the circuit of Figure 7 gives good
results in most applications.
RGB
INPUT
360V
47nF
RAIN
GAIN
BAIN
75V
Figure 7. Analog Input Interface Circuit
Figure 5. Equivalent Digital Input Circuit
VD
DIGITAL
OUTPUT
Figure 6. Equivalent Digital Output Circuit
HSYNC, VSYNC Inputs
The interface also takes a horizontal sync signal, which is used
to generate the pixel clock and clamp timing. It is possible to
operate the AD9884A without applying HSYNC (using an
external clock, external clamp, and single port output mode) but
a number of features of the chip will be unavailable, so it is
recommended that HSYNC be provided. This can be either a
sync signal directly from the graphics source, or a preprocessed
TTL or CMOS level signal. The HSYNC input includes a
Schmitt trigger buffer for immunity to noise and signals with
long rise times.
–14–
REV. B
AD9884A
In typical PC-based graphic systems, the sync signals are simply
TTL-level drivers feeding unshielded wires in the monitor
cable. Since the AD9884A operates from a 3.3 V power supply,
and TTL sources may drive a high level to 5 V or more, it is
recommended that a 1 kΩ series current-limiting resistor be placed
in series with HSYNC and COAST. If these pins are driven
more than 0.5 V outside the power supply voltages, internal
ESD protection diodes will conduct, and may dissipate considerable power if the sync source is of particularly low impedance.
If a signal is applied to the AD9884A when the IC’s power is
off, then even a 1 V signal can turn on the ESD protection
diodes. The 1 kΩ series resistor will protect the device from
overstress in this situation as well.
Serial Control Port
The serial control port (SDA, SCL) is designed for 3.3 V logic.
If there are 5 V drivers on the bus, these pins should be protected with 150 Ω series resistors.
OUTPUT SIGNAL HANDLING
The digital outputs are designed and specified to operate from a
3.3 V power supply (VDD ). They can also work with a VDD as
low as 2.5 V for compatibility with other 2.5 V logic.
CLAMPING
To properly digitize the incoming signal, the dc offset of the
input signal must be adjusted to fit the range of the on-board
A/D converters.
Most graphic systems produce RGB signals with black at ground
and white at approximately +0.75 V. However, if sync signals
are embedded in the graphics, then the sync tip is often at ground
potential, and black is at +300 mV. Then white is at approximately +1.0 V. Some common RGB line amplifier boxes use
emitter-follower buffers to split signals and increase drive capability. This introduces a 700 mV dc offset to the signal which
must be removed for proper capture by the AD9884A.
The key to clamping is to identify a portion (time) of the signal
when the graphic system is known to be producing black. An
offset is then introduced which results in the A/D converters
producing a black output (code 00h) when the known black
input is present. That offset then remains in place when other
signal levels are processed, and the entire signal is shifted to
eliminate offset errors.
In most graphic systems, black is transmitted between active
video lines. Going back to CRT displays, when the electron
beam has completed writing a horizontal line on the screen (at
the right side), the beam is deflected quickly to the left side of
the screen (called horizontal retrace) and a black signal is provided to prevent the beam from disturbing the image.
In systems with embedded sync, a blacker-than-black signal
(HSYNC) is produced briefly to signal the CRT that it is time
to begin a retrace. For obvious reasons, it is important to avoid
clamping on the tip of HSYNC. Fortunately, there is virtually
always a period following HSYNC called the back porch where
a good black reference is provided. This is the time when clamping should be done.
REV. B
The clamp timing can be established by simply exercising the
CLAMP pin at the appropriate time (with EXTCLMP = 1).
The polarity of this signal is set by the CLAMPOL bit.
A simpler method of clamp timing employs the AD9884A internal clamp timing generator. Register CLPLACE is programmed
with the number of pixel times that should pass after the trailing
edge of HSYNC before clamping starts. A second register
(CLDUR) sets the duration of the clamp. These are both 8-bit
values, providing considerable flexibility in clamp generation.
The clamp timing is referenced to the trailing edge of HSYNC
because, though HSYNC duration can vary widely, the back
porch (black reference) always follows HSYNC. A good starting point for establishing clamping is to set CLPLACE to 08h
(providing 8 pixel periods for the graphics signal to stabilize
after sync) and set CLDUR to 14h (giving the clamp 20 pixel
periods to reestablish the black reference).
Clamping is accomplished by placing an appropriate charge on
the external input coupling capacitor. The value of this capacitor affects the performance of the clamp. If it is too small, there
will be a significant amplitude change during a horizontal line
time (between clamping intervals). If the capacitor is too large,
then it will take excessively long for the clamp circuit to recover
from a large change in incoming signal offset. The recommended
value results in recovering from a step error of 100 mV to within
1/2 LSB in 10 lines with a clamp duration of 20 pixels on a
60 Hz SXGA signal.
GAIN AND OFFSET CONTROL
The AD9884A can accommodate input signals with inputs
ranging from 0.5 V to 1.0 V full scale. The full-scale range is set
in three 8-bit registers (REDGAIN, GRNGAIN, BLUGAIN).
A code of 0 in a gain register establishes a minimum input range
of 0.5 V; 255 corresponds with the maximum range of 1.0 V.
Note that INCREASING the gain setting results in an image
with LESS contrast.
The offset control shifts the entire input range, resulting in a
change in image brightness. Three 6-bit registers (REDOFST,
GRNOFST, BLUOFST) provide independent settings for each
channel.
The offset controls provide a ± 31 LSB adjustment range. This
range is connected with the full-scale range, so if the input range
is doubled (from 0.5 V to 1.0 V) then the offset step size is also
doubled (from 2 mV per step to 4 mV per step).
Figure 8 illustrates the interaction of gain and offset controls.
The magnitude of an LSB in offset adjustment is proportional
to the full-scale range, so changing the full-scale range also
changes the offset. The change is minimal if the offset setting is
near midscale. When changing the offset, the full-scale range is
not affected, but the full-scale level is shifted by the same amount
as the zero scale level.
–15–
AD9884A
PIXEL CLOCK
INVALID SAMPLE TIMES
OFFSET = 3FH
OFFSET = 1FH
1.0V
INPUT RANGE
OFFSET = 0FH
0.5V
Figure 9. Pixel Sampling Times
OFFSET = 3FH
Considerable care has been taken in the design of the AD9884A’s
clock generation circuit to minimize jitter. As indicated in Figure 11 and Table VI, the clock jitter of the AD9884A is less
than 5% of the total pixel time in all operating modes, making
the reduction in the valid sampling time due to jitter negligible.
OFFSET = 1FH
OFFSET = 0FH
The PLL characteristics are determined by the loop filter design, by the PLL Charge Pump Current (CURRENT), and by
the VCO Range setting (VCORNGE). The loop filter design is
illustrated in Figure 10. Recommended settings of VCORNGE
and CURRENT for VESA standard display modes are listed in
Table VII.
0.0V
00h
FFh
GAIN
Figure 8. Gain and Offset Control
Table V. Typical KVCO Derived From VCORNGE
CLOCK GENERATION
A Phase Locked Loop (PLL) is employed to generate the pixel
clock. In this PLL, the HSYNC input provides a reference
frequency. A Voltage Controlled Oscillator (VCO) generates a
much higher pixel clock frequency. This pixel clock is divided
by the value PLLDIV programmed into the AD9884A, and
phase compared with the HSYNC input. Any error is used to
shift the VCO frequency and maintain lock between the two
signals.
Pixel Rate (MHz)
VCORNGE
KVCO (MHz/V)
20–60
50–90
80–120
110–140
00
01
10
11
100
100
150
180
PVD
The stability of this clock is a very important element in providing the clearest and most stable image. During each pixel time,
there is a period during which the signal is slewing from the old
pixel amplitude and settling at its new value. Then there is a
time when the input voltage is stable, before the signal must
slew to a new value (Figure 9). The ratio of the slewing time to
the stable time is a function of the bandwidth of the graphics
DAC and the bandwidth of the transmission system (cable and
termination). It is also a function of the overall pixel rate.
Clearly, if the dynamic characteristics of the system remain
fixed, then the slewing and settling time is likewise fixed. This
time must be subtracted from the total pixel period, leaving the
stable period. At higher pixel frequencies, the total cycle time is
shorter, and the stable pixel time becomes shorter as well.
0.039mF
CZ
CP
0.0039mF
3.3kV
RZ
FILT
Figure 10. PLL Loop Filter Detail
Table VI. Pixel Clock Jitter vs Frequency
Any jitter in the pixel clock reduces the precision with which the
sampling time can be determined, and must also be subtracted
from the stable pixel time.
Pixel Rate
(MSPS)
Jitter p-p
(ps)
Jitter p-p
(% of Pixel Time)
135
108
94
75
65
50
40
36
25
350
400
400
450
600
500*
500*
550*
1000*
4.7%
4.3%
3.4%
3.4%
3.9%
2.4%
2.0%
1.8%
2.5%
*AD9884A in oversampled mode.
–16–
REV. B
AD9884A
Table VII. Recommended VCORNGE and CURRENT Settings for Standard Display Formats
Refresh
Rate
Horizontal
Frequency
Pixel Rate
VCORNGE
CURRENT
640 × 480
60 Hz
72 Hz
75 Hz
85 Hz
31.5 kHz
37.7 kHz
37.5 kHz
43.3 kHz
25.175 MHz
31.500 MHz
31.500 MHz
36.000 MHz
00
00
00
00
000
000
000
001
SVGA
800 × 600
56 Hz
60 Hz
72 Hz
75 Hz
85 Hz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
53.7 kHz
36.000 MHz
40.000 MHz
50.000 MHz
49.500 MHz
56.250 MHz
00
00
00
00
01
001
001
010
001
010
XGA
1024 × 768
60 Hz
70 Hz
75 Hz
80 Hz
85 Hz
48.4 kHz
56.5 kHz
60.0 kHz
64.0 kHz
68.3 kHz
65.000 MHz
75.000 MHz
78.750 MHz
85.500 MHz
94.500 MHz
01
01
01
10
10
010
011
011
011
011
SXGA
1280 × 1024
60 Hz
75 Hz
85 Hz
64.0 kHz
80.0 kHz
91.1 kHz
108.000 MHz
135.000 MHz
157.500 MHz*
10
11
01
011
100
100
UXGA
1600 × 1200
60 Hz
65 Hz
70 Hz
75 Hz
85 Hz
75.0 kHz
81.3 kHz
87.5 kHz
93.8 kHz
106.3 kHz
162.000 MHz*
175.500 MHz*
189.000 MHz*
202.500 MHz*
229.500 MHz*
01
10
10
10
10
100
100
101
101
110
Standard
Resolution
VGA
VESA Monitor Timing Standards and Guidelines, September 17, 1998
*Graphics sampled at 1/2 incoming pixel rate using Alternate Pixel Sampling mode.
15
JITTER p-p (%)
10
JITTER – %
Figure 11 illustrates the AD9884A’s jitter as a percentage of the
total clock period over the range of operating frequencies.
Though the jitter is very low over most of the range (less than
5% of the pixel period), the jitter increases at clock rates below
40 MHz. At lower frequencies, the jitter can be reduced by
operating the AD9884A at twice the desired frequency, and
using only every other data sample produced. This can be easily
implemented by placing the part in Dual Channel mode (for
example, as in Figure 21), and reading the data from only one of
the output ports. The DATACK and DATACK outputs will
run at the desired, lower, sample rate.
JITTER p-p (%)
OVERSAMPLED RATE
5
0
0
20
40
100
60
80
PIXEL CLOCK – MHz
120
140
Figure 11. Pixel Clock Jitter vs. Frequency
REV. B
–17–
160
AD9884A
TIMING
The following timing diagrams show the operation of the
AD9884A in all clock modes. The part establishes timing by
having the sample that corresponds to the pixel digitized when
the leading edge of HSYNC occurs sent to the “A” data port (to
the B data port if 0Dh, Bit 4 = 1). In Dual Channel mode, the
next sample is sent to the “B” port (to the A data port if 0Dh,
Bit 4 = 1). Subsequent samples are alternated between the “A”
and “B” data ports. In Single Channel mode, data is only sent
to the “A” data port, and the “B” port is placed in a high impedance state.
When operating in Dual Channel mode, since the first pixel
after HSYNC is always sent to the A port, there are situations
where the first DESIRED pixel (the first active pixel of a line)
may appear on the B port. If the graphics controller or memory
buffer requires that the first pixel appear on the A port, the
OUTPHASE control bit will swap the data to the A and B
ports.
The Output Data Clock signal is created so that its rising edge
always occurs between “A” data transitions, and can be used to
latch the output data externally. The HSYNC output is pipelined
with the data in a fixed timing relationship between the two in
all Single Channel modes.
Two things happen to Horizontal Sync in the AD9884A. First,
HSOUT is always produced in an active HIGH state: that is,
the leading edge of HSOUT is always a RISING edge. Then,
HSOUT is aligned with DATACK and the data outputs. This is
the sync signal that should be used to drive the rest of the display system.
The trailing edge of HSOUT is NOT time-aligned: it remains
linked to the incoming HSYNC. Refer to the timing diagrams
for HSOUT leading edge placement. HSOUT trailing edge is
coincident with HSYNC input trailing edge. There can be no
guarantee of the timing relationship between the HSOUT trailing edge and DATACK. Therefore, the leading edge of HSOUT
should be used for all display system timing.
HSOUT is forced LOW at midline, whether or not the incoming HSYNC trailing edge has arrived. If HSOUT exhibits a
50% duty cycle (while HSYNC input does not) it is an indication that the HSPOL bit is incorrectly set. This characteristic
can be used to produce an HSOUT with synchronous leading
and trailing edges by programming HSPOL to use the trailing
edge of HSYNC instead of the leading edge. In this case, if the
internal clamp function is used, be aware that the clamp position is now measured from the LEADING edge of HSYNC,
and program it accordingly.
COAST Timing
There is a pipeline in the AD9884A, which must be flushed
before valid data becomes available. In all single channel
modes, four data sets are presented before valid data is available. In all dual channel modes, two data sets are presented
before valid “A” port data is available.
In most computer systems, the HSYNC signal is provided continuously on a dedicated wire. In these systems, the COAST
input and function are unnecessary, and should not be used.
In some systems, however, HSYNC is disturbed during the
Vertical Sync period (VSYNC). In some cases, HSYNC pulses
disappear. In other systems, such as those that employ Composite Sync (CSYNC) signals or embed Sync On Green (SOG),
HSYNC includes equalization pulses or other distortions during
VSYNC. To avoid upsetting the clock generator during VSYNC,
it is important to ignore these distortions. If the pixel clock PLL
sees extraneous pulses, it will attempt to lock to this new frequency, and will have changed frequency by the end of the
VSYNC period. It then will take a few lines of correct HSYNC
timing to recover at the beginning of a new frame, resulting in a
“tearing” of the image at the top of the display.
t PER
t DCYCLE
DATACK
DATACK
t SKEW
The COAST input is provided to eliminate this problem. It is
an asynchronous input that disables the PLL input and allows
the clock to free-run at its then-current frequency. The PLL can
free-run for several lines without significant frequency drift.
DATA
HSOUT
Figure 12. Output Timing
COAST can be driven directly from a VSYNC input, or it can
be provided by the graphics controller.
Horizontal Sync Timing
Horizontal Sync is processed in the AD9884A to eliminate
ambiguity in the timing of the leading edge with respect to the
phase-delayed pixel clock and data.
The HSYNC input is used as a reference to generate the pixel
sampling clock. The sampling phase can be adjusted, with respect to HSYNC, through a full 360° in 32 steps via the PHASE
register (to optimize the pixel sampling time). Display systems
use HSYNC to align memory and display write cycles, so it is
important to have a stable timing relationship between HSOUT
and DATACK.
–18–
REV. B
AD9884A
ALTERNATE PIXEL SAMPLING MODE
A Logic 1 input on CKINV (Pin 27) shifts the sampling phase
180 degrees. CKINV can be switched between frames to implement the alternate pixel sampling mode. This allows higher
effective image resolution to be achieved at lower pixel rates,
but with lower frame rates.
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O
E O
E O E
O E
O E
O E
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O
E O
E O E
O E
O E
O E
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
Figure 16. Combined Frame Output from Graphics
Controller
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
Figure 13. Odd and Even Pixels in a Frame
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
On one frame, only even pixels are digitized. On the subsequent
frame, odd pixels are sampled. By reconstructing the entire frame
in the graphics controller, a complete image can be reconstructed.
This is very similar to the interlacing process that is employed in
broadcast television systems, but the interlacing is vertical instead
of horizontal. The frame data is still presented to the display at
the full desired refresh rate (usually 60 Hz) so there are no flicker
artifacts added.
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1 O1 E1
Figure 14. Odd Pixels from Frame 1
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2 O1 E2
Figure 15. Even Pixels from Frame 2
REV. B
–19–
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
O3 E2 O3 E2 O3 E2 O3 E2 O3 E2 O3 E2
Figure 17. Subsequent Frame from Controller
AD9884A
RGBIN
P0
P1
P2
P3
P4
P6
P5
P7
HSYNC
PXCK
HS
5 PIPE DELAY
ADCCK
DATACK
D0
DOUTA
D1
D2
D3
D4
D5
D6
D7
HSOUT
Figure 18. Single Channel Mode
RGBIN
P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
5 PIPE DELAY
ADCCK
DATACK
D2
D0
DOUTA
D4
D6
HSOUT
Figure 19. Single Channel Mode, Alternate Pixel Sampling (Even Pixels)
RGBIN
P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
5.5 PIPE DELAY
ADCCK
DATACK
DOUTA
D1
D3
D5
D7
HSOUT
Figure 20. Single Channel Mode, Alternate Pixel Sampling (Odd Pixels)
RGBIN
P0
P1
P2
P3
P4
P5
P6
P7
HSYNC
PXCK
HS
5 PIPE DELAY
ADCCK
DATACK
DOUTA
DOUTB
D0
D2
D1
D4
D3
D6
D5
D7
HSOUT
Figure 21. Dual Channel Mode, Interleaved Outputs
–20–
REV. B
AD9884A
RGBIN
P0
P1
P2
P3
P4
P5
P6
P7
HSYNC
PXCK
HS
6 PIPE DELAY
ADCCK
DATACK
DOUTA
D0
D2
D4
D6
D1
D3
D5
D7
HSOUT
Figure 22. Dual Channel Mode, Parallel Outputs
RGBIN
P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
5 PIPE DELAY
ADCCK
DATACK
DOUTA
D0
DOUTB
D4
D2
D6
HSOUT
Figure 23. Dual Channel Mode, Interleaved Outputs, Alternate Pixel Sampling (Even Pixels)
RGBIN
P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
5.5 PIPE DELAY
ADCCK
DATACK
DOUTA
D1
D5
D3
DOUTB
D7
HSOUT
Figure 24. Dual Channel Mode, Interleaved Outputs, Alternate Pixel Sampling (Odd Pixels)
RGBIN P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
6 PIPE DELAY
ADCCK
DATACK
DOUTA
D0
D4
DOUTB
D2
D6
HSOUT
Figure 25. Dual Channel Mode, Parallel Outputs, Alternate Pixel Sampling (Even Pixels)
REV. B
–21–
AD9884A
RGBIN
P0 P1 P2 P3 P4 P5 P6 P7
HSYNC
PXCK
HS
6.5 PIPE DELAY
ADCCK
DATACK
DOUTA
D1
D5
DOUTB
D3
D7
HSOUT
Figure 26. Dual Channel Mode, Parallel Outputs, Alternate Pixel Sampling (Odd Pixels)
is only necessary to have one bypass capacitor. The fundamental
idea is to have a bypass capacitor within about 0.5 cm of each
power pin. Also, avoid placing the capacitor on the opposite side
of the PC board from the AD9884A, as that interposes resistive
vias in the path.
PCB LAYOUT RECOMMENDATIONS
The AD9884A is a high precision, high speed analog device. As
such, to get the maximum performance out of the part it is
important to have a well laid-out board.
Inputs
Using the following layout techniques on the graphics inputs is
extremely important:
Minimize the trace length running into the graphics inputs. This
is accomplished by placing the AD9884A as close as possible to
the input connector. Long input trace lengths are undesirable
because they will pick up more noise from the board and other
external sources.
Place the 75 Ω termination resistors as close to the AD9884A as
possible. Any additional trace length between the termination
resistors and the input of the AD9884A increases the magnitude
of reflections, which will corrupt the graphics signal.
Use 75 Ω matched impedance traces. Trace impedances other
than 75 Ω will also increase the magnitude of reflections.
The AD9884A has very high input bandwidth (500 MHz). While
this is desirable for acquiring a high resolution PC graphics
signal with fast edges, it means that it will also capture any high
frequency noise present. Therefore, it is important to reduce the
amount of noise that gets coupled to the inputs. Avoid running
any digital traces near the analog inputs.
Due to the high bandwidth of the AD9884A, sometimes lowpass filtering the analog inputs can help to reduce noise. (For
many applications, filtering is unnecessary.) Our experiments
have shown that placing a series ferrite bead prior to the 75 Ω
termination resistor is helpful in filtering out excess noise. Specifically, we used the Part #2508051217Z0 from Fair-Rite, but
each application may work best with a different bead value.
The bypass capacitors should be connected between the power
plane and the power pin. Current should flow from the power
plane → capacitor → power pin. Do not make the power connection between the capacitor and the power pin. Placing a via
underneath the capacitor pads, down to the power plane, is
generally the best approach.
It is particularly important to maintain low noise and good
stability of PVD (the clock generator supply). Abrupt changes in
PVD can result in similarly abrupt changes in sampling clock
phase and frequency. This can be avoided by careful attention
to regulation, filtering, and bypassing. It is highly desirable to
provide a separately regulated supply for the analog circuitry
(VD and PVD).
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during Horizontal and Vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog supply
regulator, which can in turn produce changes in the regulated
analog voltage. This can be mitigated by regulating the analog
supply, or at least PVD, from a different, cleaner, power source
(for example, from a +12 V supply).
We also recommend that you use a single ground plane for the
entire board. Experience has repeatedly shown that the noise
performance is better, or at least the same, with a single ground
plane. Using multiple ground planes can be detrimental because
each separate ground plane is smaller, and long ground loops
can result.
Power Supply Bypassing
We recommend you bypass each power supply pin with a 0.1 µF
capacitor. The exception is in the case where two or more supply pins are adjacent. For these groupings of powers/grounds, it
–22–
REV. B
AD9884A
NE
PLA
ND
U
O
GR
G IT
AL
AD988
4A
DIG
ITA
L
GRO
UND P
LANE
REC
DIGITAL DATA
EIV E
R
PLL
Any noise that gets onto the HSYNC input trace will add jitter
to the system, so, try to minimize the trace length and try not to
run any digital or other high frequency traces near it.
Place the PLL loop filter components as close to the AD9884A
pins as possible.
Do not place any digital or other high frequency traces near
these components.
Voltage Reference
Bypass with a 0.1 µF capacitor. Place it as close to the AD9884A
pin as possible. Make the ground connection as short as possible.
Use the values suggested in the data sheet with 5% tolerance or
less.
Outputs (Both Data and Clocks)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, which requires
more current, which causes more internal digital noise.
REV. B
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance will
increase the current transients inside of the AD9884A, and
create more digital noise on its power supplies.
The digital inputs on the AD9884A were designed to work with
3.3 V signals. Connecting 5 V digital signals to the part may
cause damage. To accommodate 5 V digital signals, we recommend adding a series resistor at the AD9884A pin of 1 kΩ. The
only exception is the two serial interface pins, SDA and SCL.
On these two pins, a resistor value of 150 Ω should be used and
it should be placed between the AD9884A pin and the pull-up
resistors.
Figure 27.
Shorter traces reduce the possibility of reflections.
Adding a series resistor of value 50 Ω–200 Ω can suppress
reflections, reduce EMI, and reduce the current spikes inside of
the AD9884A. If series resistors are used, place them as close to
the AD9884A pins as possible, (although try not to add vias or
extra length to the output trace in order to get the resistors closer).
Digital Inputs
E
AC
DI
POWER PLANE
PUT TR
UT
O
ANALOG
In some cases, using separate ground planes is unavoidable. For
those cases, we recommend to at least place a single ground
plane under the AD9884A. The location of the split should be
at the receiver of the digital outputs. For this case it is even
more important to place components wisely because the current
loops will be much longer, (current takes the path of least resistance). An example of a current loop:
REFOUT is easily connected to REFIN with a short trace.
Avoid making this trace any longer than it needs to be.
When using an external reference, the REFOUT output,
while unused, still needs to be bypassed to ground with a
0.1 µF capacitor to avoid ringing.
–23–
AD9884A
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
128-Lead Plastic Quad Flatpack (MQFP)
(S-128)
0.134 (3.40)
MAX
0.041 (1.03)
0.035 (0.88)
0.031 (0.78)
C3495a–0–2/00 (rev. B)
0.685 (17.40)
0.677 (17.20)
0.669 (17.00)
0.555 (14.10)
0.551 (14.00)
0.547 (13.90)
128
1
103
102
SEATING
PLANE
0.791 (20.10)
0.787 (20.00)
0.783 (19.90)
TOP VIEW
(PINS DOWN)
0.921 (23.40)
0.913 (23.20)
0.906 (23.00)
0.003 (0.08)
MAX
38
65
64
39
0.110 (2.80)
0.106 (2.70)
0.102 (2.60)
0.020 (0.50)
BSC*
0.011 (0.27)
0.009 (0.22)
0.007 (0.17)
* THE ACTUAL POSITION OF EACH LEAD IS WITHIN 0.00315
(0.08) FROM ITS IDEAL POSITION WHEN MEASURED IN THE
LATERAL DIRECTION.
CENTER FIGURES ARE TYPICAL UNLESS OTHERWISE NOTED.
THE CONTROLLING DIMENSIONS ARE IN MM.
PRINTED IN U.S.A.
0.010 (0.25)
MIN
–24–
REV. B