UC1730 UC2730 UC3730 Thermal Monitor FEATURES DESCRIPTION • On-Chip Temperature Transducer • Temperature Comparator Gives Threshold Temperature Alarm • Power Reference Permits Airflow Diagnostics • Precision 2.5V Power Reference Permits Airflow Diagnostics The UC1730 family of integrated circuit devices are designed to be used in a number of thermal monitoring applications. Each IC combines a temperature transducer, precision reference, and temperature comparator allowing the device to respond with a logic output if temperatures exceed a user programmed level. The reference on these devices is capable of supplying in excess of 250mA of output current − by setting a level of power dissipation the rise in die temperature will vary with airflow past the package, allowing the IC to respond to airflow conditions • Transducer Output is Easily Scaled for Increased Sensitivity • Low 2.5mA Quiescent Current BLOCK DIAGRAM These devices come in an 8-Pin DIP, plastic or ceramic, a 5-Pin TO-220 or a PLCC-20 version. In the 8-Pin version, a PTAT (proportional to absolute temperature) output reports die temperature directly. This output is configured such that its output level can be easily scaled up with two external gain resistors. A second PTAT source is internally referenced to the temperature comparator. The other input to this comparator can then be externally programmed to set a temperature threshold. When this temperature threshold is exceeded an alarm delay output is activated. Following the activation of the delay output, a separate open collector output is turned on. The delay pin can be programmed with an external RC to provide a time separation between activation of the delay pin and the alarm pin, permitting shutdown diagnostics in applications where the open collector outputs of multiple parts are wire OR’ed together. The 5-Pin version in the TO-220 package is well suited for monitoring heatsink temperatures. Enhanced airflow sensitivities can be obtained with this package by mounting the device to a small heatsink in the airstream. This version of the device does not include the PTAT output or the open collector alarm output. Pin numbers shown for 8-Pin DIP, ( ) number for 5-Pin TO-220. 10/94 Powered by ICminer.com Electronic-Library Service CopyRight 2003 UC1730 UC2730 UC3730 ABSOLUTE MAXIMUM RATINGS T, 5-Pin Plastic DIP TO-220 . . . . . . . . . . . . . . . . . . . . 65°C/W Thermal Resistance Junction to Case N, 8-Pin Plastic DIP. . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W J, 8-Pin Ceramic DIP. . . . . . . . . . . . . . . . . . . . . . . . . . 40°C/W T, 5-Pin Plastic TO-220 . . . . . . . . . . . . . . . . . . . . . . . . . 5°C/W Operating Junction Temperature . . . . . . . . . -55°C to +150°C Storage Temperature . . . . . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 Seconds). . . . . . . . . 300°C Note 1: Voltages are referenced to ground. Currents are positive into, negative out of, the specified terminals. Note 2: Consult Packaging section of Databook for thermal limitations and considerations of package. Input Supply Voltage, (+VIN). . . . . . . . . . . . . . . . . . . . . . . 40V Alarm Output Voltage (8-Pin Version Only) . . . . . . . . . . . 40V Alarm Delay Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V Alarm Threshold Set Voltage . . . . . . . . . . . . . . . . . . . . . . 10V 2.5V Reference Output Current . . . . . . . . . . . . . . . . . -400 mA Alarm Output Current (8-Pin Version Only) . . . . . . . . . . 0 mA Power Dissipation at TA = 25°C (Note 2) . . . . . . . . . 1000 mW Power Dissipation at TC = 25°C (Note 2) . . . . . . . . . 2000 mW Thermal Resistance Junction to Ambient N, 8-Pin Plastic DIP . . . . . . . . . . . . . . . . . . . . . . . . . 110°C/W J, 8-Pin Ceramic DIP . . . . . . . . . . . . . . . . . . . . . . . . 110°C/W CONNECTION DIAGRAMS DIL-8 (TOP VIEW) N or J Package PLCC-20 (TOP VIEW) Q Package PACKAGE PIN FUNCTION 5-PIN TO-220 (TOP VIEW) T Package FUNCTION PIN N/C ALARM DELAY ALARM OUTPUT +VIN GND N/C PTAT+ PTAT2.5V REFERENCE 2.5V REFERENCE ALARM THRESHOLD SET N/C 1-3 4 5 6 7 8-13 14 15 16 17 18 19-20 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TJ = 0°C to +100°C for the UC3730, -25°C to + 100°C for the UC2730 and -55°C to +125°C for the UC1730, +VIN = + 5V, and PTAT– = 0V. TA = TJ. PARAMETERS INPUT SUPPLY Supply Current TEST CONDITIONS MIN TYP MAX UNITS +VIN = 35V 2.8 4.0 mA +VIN = 5V 2.3 3.5 mA 2.5 2.525 V REFERENCE Output Voltage TJ = 25°C 2.475 2.46 Load Regulation Over Temperature IOUT = 0 to 250mA Line Regulation +VIN = 5 to 25V 2.54 V 8.0 25 mV 1.0 5.0 mV 1.50 1.525 V 10 °C 0.005 0.02 %/V 3.0 2.0 8.0 5.0 15 °C mV TEMPERATURE COMPARATOR Temperature Comparator Threshold at 300°K (26.85°C), Nominally 5mV/°K, VINPUT High to Low Temperature Error 1.475 -10 Threshold Line Regulation +VIN = 5 to 25V Temperature Linearity Threshold Hysteresis Note 2 Input Bias Current VINPUT at 1.5V -0.5 -0.1 µA Max Output Current VOUT = 1V 1.2 3.0 mA Output Sat Voltage IOUT = 100µA Powered by ICminer.com Electronic-Library Service CopyRight 2003 0.05 2 0.25 V UC1730 UC2730 UC3730 Unless otherwise stated, these specifications apply for TJ = 0°C to +100°C for the UC3730, ELECTRICAL CHARACTERISTICS (cont): -25°C to + 100°C for the UC2730 and -55°C to +125°C for the UC1730, +VIN = + 5V, and PTAT– = 0V. TA = TJ. PARAMETERS TEMPERATURE COMPARATOR (cont.) Output Leakage Current TEST CONDITIONS MIN TYP MAX UNIT 0.01 1.0 µA 1.460 1.50 1.54 V 14.6 -12 15 15.4 12 V °C VOUT = 1V PTAT BUFFER (8-Pin N, or J Version Only) Output Voltage at 300°K (26.85°C), Nominally 5mV/°K In 10X Config. + VIN = 25V Temperature Error Temperature Linearity (Note 2) Line Regulation Load Regulation Dropout Voltage 2.0 5.0 °C +VIN = 5 to 25V 0.02 0.04 %/V IOUT = 0 to 2mA PTAT + TO +VIN 1.0 3.0 mV 1.9 2.5 Input Bias Current at PTAT– Input V µA -3.0 -1.0 1.1 Threshold Hysteresis Voltage Input Bias Current Alarm Delay Input Low to High Alarm Delay Voltage > VTH Alarm Delay Voltage < VTH 1.2 100 0.1 1.3 250 0.5 V mV µA Max Output Current VOUT = 1V 7.0 Output Sat Voltage IOUT = 3mA 15 0.25 0.45 mA V 0.1 2.0 µA ALARM BUFFER COMPARATOR (8-Pin N, or J Version Only) Threshold Voltage (VTH) Output Leakage VOUT = 35V Note 2: This parameter is guaranteed by design and is not tested in production. APPLICATIONS AND OPERATION INFORMATION Scaling the PTAT Output (8 Pin Version Only) R2 VOUT = 5 x 1+ mV ⁄ ° K R1 (Recommended Range for R1 is 2k to 4k) VREF Maximum Output Current vs Input Supply Powered by ICminer.com Electronic-Library Service CopyRight 2003 Junction Temperature Rise vs Airflow UC3730N (8Pin Plastic Dip) 3 UC1730 UC2730 UC3730 APPLICATIONS AND OPERATION INFORMATION (Cont.) Setting a Temperature Threshold Temperature Threshold (°C) 2.5V R2 =( − 273.15 )x 0.005 R1+R2 Note:For airflow monitoring a power dissipation level can be set with a resistive load, RL, on the reference output. PD = (+ VIN - 2.5V)2/RL. Dual Speed Fan Control 2.5V R2 x − 273.15 0.005 R1+R2 2.5V RX TL(°C) = x − 273.15 0.005 R1+RX R3 Where: RX = R2 × R2 + R3 TH(°C) = UNITRODE INTEGRATED CIRCUITS 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX (603) 424-3460 Powered by ICminer.com Electronic-Library Service CopyRight 2003 4 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated Powered by ICminer.com Electronic-Library Service CopyRight 2003