FIXED 2.5 AND 5 VOLT MINIATURE VOLTAGE REGULATORS ZMR SERIES ISSUE 3- FEBRUARY 1998 DEVICE DESCRIPTION FEATURES The ZMR series of three terminal fixed positive voltage regulators feature internal current limit and will shut down under thermal overload conditions making the devices difficult to destroy. • The circuit design offers an exceptionally low quiescent current, only 30µA for the 2.5 volt device, ideal for low power applications. The initial devices in the series regulate to 2.5 or 5 volts with a drive capability up to 50mA, however, the flexible design will allow other voltage selections to be made. The device is designed with space saving in mind and is available in the small outline SOT23 package as well as SOT89 for higher power applications. The SOT23 package is ideal for applications where space is restricted. The device is also available in through hole TO92 package. • • • • • • • • • Small outline SOT23 and SOT89 packages TO92 package 2.5V and 5V output 22.5V maximum input voltage (ZMR25H) 25V maximum input voltage (ZMR50H) Output current up to 50mA Very low Quiesent current (30µA) Unconditionally stable Other output voltages possible Internal short circuit current limit VOLTAGE RANGE ZMR250 ZMR500 ZMR25H ZMR50H 2.5V 5.0V 2.5V 5.0V SCHEMATIC DIAGRAM Vin Vout Gnd 4-104 2003 Powered by ICminer.com Electronic-Library Service CopyRight ZMR SERIES ABSOLUTE MAXIMUM RATINGS Input voltage (ZMR25H) (ZMR50H) 22.5V 25V ZMR250 ZMR500 20V 20V Package power dissipation (Tamb=25 °C) SOT23 500mW (Note 3) TO92 600mW Output current (IO) 100mA Operating temperature Storage temperature -55 to 125°C -65 to 150°C SOT89 1.5W (Note 3) Note: 1. The maximum operating input voltage and output current of the device will be governed by the maximum power dissipation of the selected package. Maximum package power dissipation is specified at 25 °C and must be linearly derated to zero at Tamb =125°C. 2. The following data represents pulse test conditions with junction temperatures as indicated at the initiation of the test. Continuous operation of the devices with the stated conditions might exceed the power dissipation limits of the chosen package. 3. Maximum power dissipation, for the SOT23 and SOT89 packages, is calculated assuming that the device is mounted on a ceramic substrate measuring 15 x 15 x 0.6mm. ZMR25H ELECTRICAL CHARACTERISTICS TEST CONDITIONS (Unless otherwise stated):Tj=25°C, IO=10mA, Vin=6.5V SYMBOL PARAMETER VO CONDITIONS Output Voltage MIN. TYP. MAX. UNITS 2.438 2.5 2.563 V IO=0 to 50mA Tj=-55 to 125°C 2.360 2.640 V Vin=4.5 to 22.5V IO=0 to 50mA Tj=-55 to 125°C 2.360 2.640 V ∆VO Line Regulation Vin=4.5 to 22.5V 5 15 mV ∆VO Load Regulation IO=0 to 50mA IO=0 to 10mA 20 12 30 mV mV Supply Current Tj=-55 to 125°C 30 40 µA ∆ls Supply Current Change IO=0 to 50mA Vin=4.5 to 22.5V 1 2 ±10 10 µA µA Vn Output Noise Voltage f=10Hz to 10KHz 65 µV rms 55 75 dB 4.2 3.9 V ls ∆Vin /∆VO Ripple Rejection Vin ∆VO /∆T Vin=6.3 to 18V f=120Hz Input Voltage Required To Maintain Regulation Average Temperature Coefficient of VO IO=5.0mA Tj=-55 to 125°C Powered by ICminer.com Electronic-Library Service CopyRight 4-105 2003 0.275 0.700 mV/°C ZMR SERIES ZMR50H ELECTRICAL CHARACTERISTICS TEST CONDITIONS (Unless otherwise stated):Tj=25°C, IO=10mA, Vin=10V SYMBOL PARAMETER VO CONDITIONS Output Voltage MIN. TYP. MAX. UNITS 4.875 5 5.125 V IO=0 to 50mA Tj=-55 to 125°C 4.780 5.160 V Vin=7 to 25V IO=0 to 50mA Tj=-55 to 125°C 4.780 5.175 V ∆VO Line Regulation Vin=7 to 25V 5 15 mV ∆VO Load Regulation IO=0 to 50mA IO=0 to 10mA 25 15 40 mV mV Supply Current Tj=-55 to 125°C 50 70 µA ∆ls Supply Current Change IO=0 to 50mA Vin=7 to 25V 1 2 ±10 10 µA µA Vn Output Noise Voltage f=10Hz to 10KHz 90 ls ∆Vin /∆VO Ripple Rejection Vin ∆VO /∆T Vin=8 to 18V f=120Hz Input Voltage Required To Maintain Regulation Average Temperature Coefficient of VO 55 4-106 2003 Powered by ICminer.com Electronic-Library Service CopyRight 72 dB 7 IO=5.0mA Tj=-55 to 125°C µV rms 6.7 0.275 V 0.700 mV/°C ZMR SERIES ZMR250 ELECTRICAL CHARACTERISTICS TEST CONDITIONS (Unless otherwise stated):Tj=25°C, IO=10mA, Vin=6.5V SYMBOL PARAMETER VO CONDITIONS Output Voltage MIN. TYP. MAX. UNITS 2.438 2.5 2.563 V IO=0 to 50mA Tj=-55 to 125°C 2.360 2.640 V Vin=4.5 to 20V IO=0 to 50mA Tj=-55 to 125°C 2.360 2.640 V ∆VO Line Regulation Vin=4.5 to 20V 5 15 mV ∆VO Load Regulation IO=0 to 50mA IO=0 to 10mA 20 12 30 mV mV Supply Current Tj=-55 to 125°C 30 40 µA ∆ls Supply Current Change IO=0 to 50mA Vin=4.5 to 20V 1 2 ±10 10 µA µA Vn Output Noise Voltage f=10Hz to 10KHz 65 µV rms 55 75 dB 4.2 3.9 V ls ∆Vin /∆VO Ripple Rejection Vin ∆VO /∆T Vin=6.3 to 18V f=120Hz Input Voltage Required To Maintain Regulation Average Temperature Coefficient of VO IO=5.0mA Tj=-55 to 125°C Powered by ICminer.com Electronic-Library Service CopyRight 4-107 2003 0.275 0.700 mV/°C ZMR SERIES ZMR500 ELECTRICAL CHARACTERISTICS TEST CONDITIONS (Unless otherwise stated):Tj=25°C, IO=10mA, Vin=10V SYMBOL PARAMETER VO CONDITIONS Output Voltage MIN. TYP. MAX. UNITS 4.875 5 5.125 V IO=0 to 50mA Tj=-55 to 125°C 4.780 5.160 V Vin=7 to 20V IO=0 to 50mA Tj=-55 to 125°C 4.780 5.175 V ∆VO Line Regulation Vin=7 to 20V 5 15 mV ∆VO Load Regulation IO=0 to 50mA IO=0 to 10mA 25 15 40 mV mV Supply Current Tj=-55 to 125°C 50 70 µA ∆ls Supply Current Change IO=0 to 50mA Vin=7 to 20V 1 2 ±10 10 µA µA Vn Output Noise Voltage f=10Hz to 10KHz 90 µV rms 55 72 dB 7 6.7 V ls ∆Vin /∆VO Ripple Rejection Vin ∆VO /∆T Vin=8 to 18V f=120Hz Input Voltage Required To Maintain Regulation Average Temperature Coefficient of VO IO=5.0mA Tj=-55 to 125°C 4-108 2003 Powered by ICminer.com Electronic-Library Service CopyRight 0.275 0.700 mV/°C ZMR SERIES TYPICAL CHARACTERISTICS 5.02 60 5.00 4.98 4.96 2.52 Io=5mA Vin=Vo+4 2.50 ZMR50H 50 Quiescent Current (µA) Output Voltage Io=10mA Io=5mA Vin=Vo+4 ZMR50H 2.48 2.46 40 ZMR25H 30 20 10 ZMR25H -50 -25 0 25 50 0 75 100 125 2 4 Temperature (°C) 6 10 12 14 16 18 8 20 Input Voltage (V) Output Voltage Temperature Quiescent Current v Voltage 60 Io=0 Vin=Vo+4 Quiescent Current (µA) 34 Quiescent Current (µA) 32 30 ZMR25H 28 Io=0 Vin=Vo+4 56 52 48 ZMR50H 44 26 40 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) Quiescent Current v Temperature Quiescent Current v Temperature 2.5 49 Io=10mA ZMR50H 2.0 Io=0 Vin=Vo+4 48 Drop-Out Voltage (V) Quiescent Current (µA) 50 47 30 29 ZMR25H 28 Io=0 Vin=Vo+4 27 0.1 1 10 100 ZMR50H 1.5 0.5 0 -50 -25 Output Current Quiescent Current v Output Current ZMR25H 1.0 0 25 50 75 100 125 Temperature (°C) Drop-Out Voltage v Temperature Powered by ICminer.com Electronic-Library Service CopyRight 4-109 2003 ZMR SERIES TYPICAL CHARACTERISTICS 90 I O= 10mA I o= 2mA VIN = VOUT+ 4V 80 Ripple Rejection (dB) Output Impedance (Ω) 10 1.0 ZMR25H ZMR50H 0.1 Io= 10mA 70 ZMR25H ZMR50H 60 50 40 30 20 10 0 10 0.01 100 1K 100K 10K 100 1K 10K Ripple Rejection v Ripple Frequency Output Impedance v Frequency 5V Vin 0 0V 0.4 ZMR25H 0 COUT=0 VIN=Vo+4 dIo/dt=1A/µs 0.4 -0.4 ZMR50H -0.4 40 20 0 80 60 Output Voltage Deviation (V) Output Voltage Deviation (V) 10mA Load Current 0 100 0.4 ZMR25H 0 COUT=0 VIN=Vo+4 dVIN/dt=5V/µs 0.4 -0.4 0 10 20 30 40 Line Transient Response 800 2 Surface Mount Devices Through Hole Device TO92 Power Dissipation (mW) SOT89 1 SOT23 600 400 200 0 0 -25 0 25 50 50 Time (µs) Load Transient Response -50 -0.4 ZMR50H 0 Time (µs) Power Dissipation (mW) 100K Ripple Frequency (Hz) Frequency (Hz) 75 100 125 Temperature (°C) Power Derating 4-110 2003 Powered by ICminer.com Electronic-Library Service CopyRight -50 -25 0 25 50 75 100 125 Temperature (°C) Power Derating ZMR SERIES TYPICAL CHARACTERISTICS 5.02 60 5.00 4.98 4.96 2.52 Io=5mA Vin=Vo+4 2.50 ZMR500 50 Quiescent Current (µA) Output Voltage Io=10mA Io=5mA Vin=Vo+4 ZMR500 2.48 2.46 40 ZMR250 30 20 10 ZMR250 -50 -25 0 25 50 0 75 100 125 2 4 Temperature (°C) 6 10 12 14 16 18 8 20 Input Voltage (V) Output Voltage Temperature Quiescent Current v Voltage 60 Io=0 Vin=Vo+4 Quiescent Current (µA) 34 Quiescent Current (µA) 32 30 ZMR250 28 Io=0 Vin=Vo+4 56 52 48 ZMR500 44 26 40 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) Quiescent Current v Temperature Quiescent Current v Temperature 2.5 49 Io=10mA ZMR500 2.0 Io=0 Vin=Vo+4 48 Drop-Out Voltage (V) Quiescent Current (µA) 50 47 30 29 ZMR250 28 Io=0 Vin=Vo+4 27 0.1 1 10 ZMR500 1.5 ZMR250 1.0 0.5 100 Output Current Quiescent Current v Output Current 4-111 2003 Powered by ICminer.com Electronic-Library Service CopyRight 0 -50 -25 0 25 50 75 100 125 Temperature (°C) Drop-Out Voltage v Temperature ZMR SERIES TYPICAL CHARACTERISTICS 90 I O= 10mA I o= 2mA VIN = VOUT+ 4V 80 Ripple Rejection (dB) Output Impedance (Ω) 10 1.0 ZMR250 ZMR500 0.1 Io= 10mA 70 ZMR250 ZMR500 60 50 40 30 20 10 0 10 0.01 100 1K 100K 10K 100 1K 10K Ripple Rejection v Ripple Frequency Output Impedance v Frequency 5V Vin 0 0V 0.4 ZMR250 0 COUT=0 VIN=Vo+4 dIo/dt=1A/µs 0.4 -0.4 ZMR500 -0.4 40 20 0 80 60 Output Voltage Deviation (V) Output Voltage Deviation (V) 10mA Load Current 0 0.4 ZMR250 0 COUT=0 VIN=Vo+4 dVIN/dt=5V/µs 0.4 -0.4 100 0 10 20 30 40 Line Transient Response 800 2 Surface Mount Devices Through Hole Device TO92 Power Dissipation (mW) SOT89 1 SOT23 0 600 400 200 0 -25 0 25 50 50 Time (µs) Load Transient Response -50 -0.4 ZMR500 0 Time (µs) Power Dissipation (mW) 100K Ripple Frequency (Hz) Frequency (Hz) 75 100 125 Temperature (°C) Power Derating Powered by ICminer.com Electronic-Library Service CopyRight 4-112 2003 -50 -25 0 25 50 75 100 125 Temperature (°C) Power Derating ZMR SERIES CONNECTION DIAGRAMS SOT23 Package Suffix – F TO92 Package Suffix – C Top View Bottom View SOT89 Package Suffix – Z Top View ORDERING INFORMATION Part Number Package Part Mark ZMR250C TO92 ZMR250 ZMR250F SOT23 25K ZMR250Z SOT89 25K ZMR25HC TO92 ZMR25H ZMR25HF SOT23 25X ZMR25HZ SOT89 25T ZMR500C TO92 ZMR500 ZMR500F SOT23 50K ZMR500Z SOT89 50K ZMR50HC TO92 ZMR50H ZMR50HF SOT23 50R ZMR50HZ SOT89 50T Powered by ICminer.com Electronic-Library Service CopyRight 4-113 2003