ISD MicroTAD-16M Single-Chip Voice Record/Playback Device 16-Minute Duration Preliminary Data Sheet GENERAL DESCRIPTION The ISD MicroTAD-16M ChipCorder® Product provides high-quality, 3-volt, single-chip record/playback solutions for 16-minute messaging applications which are ideal for telephone answering devices (TADs). The CMOS-based devices include an on-chip oscillator, antialiasing filter, smoothing filter, AutoMute™ feature, audio amplifier, and high density, multilevel Flash storage array. The ISD MicroTAD-16M is designed to be used in a microprocessor- or microcontroller-based system. Address and control are accomplished through a Serial Peripheral Interface (SPI) or Microwire Serial Interface to minimize pin count. Recordings are stored in on-chip nonvolatile memory cells, providing zero-power message storage. This unique, single-chip solution is made possible through ISD’s patented multilevel storage technology. Voice and audio signals are stored directly into memory in their natural form, providing high-quality, solid-state voice reproduction. Figure: ISD MicroTAD-16M Block Diagram May 1999 ISD · 2727 North First Street, San Jose, CA 95125 · TEL: 408/943-6666 · FAX: 408/544-1787 · http://www.isd.com ISD MicroTAD-16M FEATURES • Single-chip voice record/playback solution • Single +3 volt supply • Low-power consumption – Operating current: ICC Play = 15 mA (typical) ICC Rec = 25 mA (typical) – Standby current: 1 µA (typical) • Microcontroller SPI or Microwire™ Serial Interface • Fully addressable to handle multiple messages • Nonvolatile message storage • Power consumption controlled by SPI or Microwire control register • Single-chip duration of 16 minutes • 100-year message retention (typical) • 4.0 KHz sample rate • 100K record cycles (typical) • Typical band pass filter 1.7 KHz • On-chip clock source • High-quality, natural voice/audio reproduction • Available in die form, PDIP, SOIC, and TSOP • AutoMute feature provides background noise attenuation during periods of silence • No algorithm development required ii Voice Solutions in Silicon™ ISD MicroTAD-16M DETAILED DESCRIPTION PIN DESCRIPTIONS SPEECH/SOUND QUALITY VOLTAGE INPUTS (VCCA, VCCD) The ISD MicroTAD-16M ChipCorder is offered at 4.0 KHz sampling frequency. To minimize noise, the analog and digital circuits in the ISD MicroTAD-16M device use separate power busses. These +3 V busses are brought out to separate pins and should be tied together as close to the supply as possible. In addition, these supplies should be decoupled as close to the package as possible. The speech samples are stored directly into on-chip nonvolatile memory without the digitization and compression associated with other solutions. Direct analog storage provides a natural sounding reproduction of voice, music, tones, and sound effects not available with most solid-state solutions. FLASH STORAGE One of the benefits of ISD’s ChipCorder technology is the use of on-chip nonvolatile memory, which provides zero-power message storage. The message is retained for up to 100 years (typically) without power. In addition, the device can be re-recorded (typically) over 100,000 times. MICROCONTROLLER INTERFACE A four-wire (SCLK, MOSI, MISO, SS) SPI interface is provided for ISD MicroTAD-16M control and addressing functions. The ISD MicroTAD-16M is configured to operate as a peripheral slave device, with a microcontroller-based SPI bus interface. Read/Write access to all the internal registers occurs through this SPI interface. An interrupt signal (INT) and internal read-only Status Register are provided for handshake purposes. GROUND INPUTS (VSSA, VSSD) The ISD MicroTAD-16M utilizes separate analog and digital ground busses. The analog ground (VSSA) pins should be tied together as close to the package as possible and connected through a low-impedance path to power supply ground. The digital ground (VSSD) pin should be connected through a separate low-impedance path to power supply ground. These ground paths should be large enough to ensure that the impedance between the VSSA pins and the VSSD pin is less than 3 Ω. The backside of the die is connected to VSS through the substrate resistance. In a chip-onboard design, the die attach area must be connected to VSS or left floating. PROGRAMMING The ISD MicroTAD-16M is also ideal for playbackonly applications, where single or multiple message Playback is controlled through the SPI port. Once the desired message configuration is created, duplicates can easily be generated via an ISD programmer or a 3rd party programmer. ISD 1 ISD MicroTAD-16M Figure 1: ISD MicroTAD-16M TSOP and PDIP/SOIC Pinouts ISD4004 ISD4004 28-PIN TSOP PDIP/SOIC Figure 2: ISD MicroTAD-16M ANA IN Modes 2 Voice Solutions in Silicon™ ISD MicroTAD-16M NON-INVERTING ANALOG INPUT (ANA IN+) SLAVE SELECT (SS) This pin is the non-inverting analog input that transfers the signal to the device for recording. The analog input amplifier can be driven single ended or differentially. In the single-ended input mode, a 32 mVp-p (peak-to-peak) maximum signal should be capacitively connected to this pin for optimal signal quality. This capacitor value, together with the 3 KΩ input impedance of ANA IN+, is selected to give cutoff at the low frequency end of the voice passband. In the differential-input mode, the maximum input signal at ANA IN+ should be 16 mVp-p for optimal signal quality. The circuit connections for the two modes are shown in Figure 2 on page 2. This input, when LOW, will select the ISD MicroTAD16M device. INVERTING ANALOG INPUT (ANA IN–) SERIAL CLOCK (SCLK) This pin is the inverting analog input that transfers the signal to the device for recording in the differential-input mode. In this differential-input mode, a 16 mVp-p maximum input signal at ANA IN– should be capacitively coupled to this pin for optimal signal quality as shown in the ISD MicroTAD16M ANA IN Modes, Figure 2. This capacitor value should be equal to the coupling capacitor used on the ANA IN+ pin. The input impedance at ANA IN– is nominally 56 KΩ. In the single-ended mode, ANA IN– should be capacitively coupled to VSSA through a capacitor equal to that used on the ANA IN+ input. This is the clock input to the ISD MicroTAD-16M. It is generated by the master device (microcontroller) and is used to synchronize data transfers in and out of the device through the MISO and MOSI lines. Data is latched into the ISD MicroTAD-16M on the rising edge of SCLK and shifted out of the device on the falling edge of SCLK. AUDIO OUTPUT (AUD OUT) This pin provides the audio output to the user. It is capable of driving a 5 KΩ impedance. It is recommended that this pin be AC coupled. NOTE ISD The AUDOUT pin is always at 1.2 volts when the device is powered up. When in playback, the output buffer connected to this pin can drive a load as small as 5 KΩ. When in record, a resistor connects AUDOUT to the internal 1.2 volt analog ground supply. This resistor is approximately 850 KΩ. This relatively high impedance allows this pin to be connected to an audio bus without loading it down. MASTER OUT SLAVE IN (MOSI) This is the serial input to the ISD MicroTAD-16M device. The master microcontroller places data on the MOSI line one half-cycle before the rising clock edge to be clocked in by the ISD MicroTAD16M device. MASTER IN SLAVE OUT (MISO) This is the serial output of the ISD MicroTAD-16M device. This output goes into a high-impedance state if the device is not selected. INTERRUPT (INT) The ISD MicroTAD-16M interrupt pin goes LOW and stays LOW when an Overflow (OVF) or End of Message (EOM) marker is detected. This is an open drain output pin. Each operation that ends in an EOM or Overflow will generate an interrupt including the message cueing cycles. The interrupt will be cleared the next time an SPI cycle is initiated. The interrupt status can be read by an RINT instruction. Overflow Flag (OVF)—The Overflow flag indicates that the end of the ISD MicroTAD-16M’s analog memory has been reached during a record or playback operation. End of Message (EOM)—The End-of-Message flag is set only during playback operation when an EOM is found. There are eight EOM flag position options per row. 3 ISD MicroTAD-16M ROW ADDRESS CLOCK (RAC) This is an open drain output pin that provides a signal with a 400 ms period at the 4 KHz sampling frequency. (This represents a single row of memory and there are 2400 rows of memory in the ISD MicroTAD-16M devices.) This signal stays HIGH for 350 ms and stays LOW for 50 ms when it reaches the end of a row. The RAC pin stays HIGH for 218.76 µsec and stays LOW for 31.26 µsec in Message Cueing mode (see page 5 for a more detailed description of Message Cueing). Refer to the AC Parameters table for RAC timing information on other sample rate products. When a record command is first initiated, the RAC pin remains HIGH for an extra TRACLO period. This is due to the need to load sample and hold circuits internal to the device. This pin can be used for message management techniques. EXTERNAL CLOCK INPUT (XCLK) The external clock input for the ISD MicroTAD-16M product has an internal pull-down device. These products are configured at the factory with an internal sampling clock frequency centered to ±1 percent of specification. The frequency is then maintained to a variation over the entire commercial temperature and operating voltage ranges as defined by the minimum/maximum limits in the applicable AC Parameters table. The internal clock has a tolerance, over the extended temperature, industrial temperature and voltage ranges as defined by the minimum/maximum limits in the applicable AC Parameters table. A regulated power supply is recommended for industrial temperature range parts. If greater precision is required, the device can be clocked through the XCLK pin in Table 1. 4 Table 1: External Clock Input Clocking Table Part Number Sample Rate Required Clock ISD MicroTAD-16M 4.0 KHz 512 KHz This recommended clock rate should not be varied because the antialiasing and smoothing filters are fixed. Thus, aliasing problems can occur if the sample rate differs from the one recommended. The duty cycle on the input clock is not critical, as the clock is immediately divided by two internally. If the XCLK is not used, this input should be connected to ground. AUTOMUTE™ FEATURE (AM CAP) This pin is used in controlling the AutoMute feature. The AutoMute feature attenuates the signal when it drops below an internally set threshold. This helps to eliminate noise (with 6 dB of attenuation) when there is no signal (i.e., during periods of silence). A 1 µF capacitor to ground should be connected to the AM CAP pin. This capacitor becomes a part of an internal peak detector which senses the signal amplitude (peak). This peak level is compared to an internally set threshold to determine the AutoMute trip point. For large signals the AutoMute attenuation is set to 0 dB while 6 dB of attenuation occurs for silence. The 1 µF capacitor also affects the rate at which the AutoMute feature changes with the signal amplitude (or the attack time). The Automute feature can be disabled by connecting the AM CAP pin to VCCA. Voice Solutions in Silicon™ ISD MicroTAD-16M SERIAL PERIPHERAL INTERFACE (SPI) DESCRIPTION The ISD MicroTAD-16M operates from an SPI serial interface. The SPI interface operates with the following protocol. The data transfer protocol assumes that the microcontroller’s SPI shift registers are clocked on the falling edge of the SCLK. With the ISD MicroTAD16M, data is clocked in on the MOSI pin on the rising clock edge. Data is clocked out on the MISO pin on the falling clock edge. 1. All serial data transfers begin with the falling edge of SS pin. 2. SS is held LOW during all serial communications and held HIGH between instructions. 3. Data is clocked in on the rising clock edge and data is clocked out on the falling clock edge. 4. Play and Record operations are initiated by enabling the device by asserting the SS pin LOW, shifting in an opcode and an address field to the ISD MicroTAD-16M device (refer to the Opcode Summary on the page 6). 5. The opcodes and address fields are as follows: <8 control bits> and <16 address bits>. 6. Each operation that ends in an EOM or Overflow will generate an interrupt, including the Message Cueing cycles. The Interrupt will be cleared the next time an SPI cycle is initiated. 7. As Interrupt data is shifted out of the ISD MicroTAD-16M MISO pin, control and address data is simultaneously being shifted into the MOSI pin. Care should be taken such that the data shifted in is compatible with current system operation. It is possible to read interrupt data and start a new operation within the same SPI cycle. MESSAGE CUEING Message cueing allows the user to skip through messages, without knowing the actual physical location of the message. This operation is used during playback. In this mode, the messages are skipped 1600 times faster than in normal playback mode. It will stop when an EOM marker is reached. Then, the internal address counter will point to the next message. If you are utilizing the Message Cueing Command, you must perform the following Message Cueing procedure to ensure proper Message Cueing for the MicroTAD product. Failure to follow this procedure may result in inaccurate Message Cueing. Procedure for Proper Message Cueing: A single “dummy” STOP command must be sent to the device before executing a Message Cueing (MC) or SET Message Cueing (SET MC) Instruction. The “dummy” STOP instruction consists of a command with control bits set as follows: RUN bit = 0 PLAY/RECORD bit = 0 PU bit = 1 IAB bit = 1 MC bit = 0 That is, a hex “30” is shifted into the device as a command. One or more MC or SET MC commands may be executed following this command. It is not necessary to repeat the “dummy” STOP command until after a subsequent playback operation. 8. An operation begins with the RUN bit set and ends with the RUN bit reset. 9. All operations begin with the rising edge of SS. ISD 5 ISD MicroTAD-16M Table 2: Opcode Summary Instruction Opcode <8 bits> Address <16 bits> Operational Summary POWERUP 00100XXX Power-Up: Device will be ready for an operation after TPUD. SETPLAY 11100XXX <A15–A0> Initiates Playback from address <A15–A0>. PLAY 11110XXX Playback from the current address (until EOM or OVF). SETREC 10100XXX <A15–A0> Initiates a Record operation from address <A15–A0>. REC 10110XXX Records from current address until OVF is reached. SETMC 11101XXX <A15–A0> Initiates Message Cueing (MC) from address <A15–A0>. MC1 11111XXX Performs a Message Cue. Proceeds to the end of the current message (EOM) or enters OVF condition if no more messages are present. STOP 0X110XXX Stops current operation. STOPPWRDN 0X01XXXX Stops current Operation and enters stand-by (power-down) mode. RINT2 0X110XXX Read Interrupt status bits: Overflow and EOM. 1. Message Cueing can be selected only at the beginning of a play operation. 2. As the Interrupt data is shifted out of the ISD MicroTAD-16M, control and address data is being shifted in. Care should be taken such that the data shifted in is compatible with current system operation. It is possible to read interrupt data and start a new operation at the same time. See Figure 5 through Figure 8 for Opcode format. POWER-UP SEQUENCE The ISD MicroTAD-16M will be ready for an operation after TPUD (50 ms approximately for 4 KHz sample rate). The user needs to wait TPUD before issuing an operational command. For example, to play from address 00 the following programing cycle should be used. Record Mode 1. Send POWERUP command. 2. Wait TPUD (power-up delay). 3. Send POWERUP command. 4. Send SETREC command with address 00. 5. Send REC command. Playback Mode 1. Send POWERUP command. 2. Wait TPUD (power-up delay). The device will start recording at address 00 and it will generate an interrupt when an overflow is reached (end of memory array). It will then stop recording. 3. Send SETPLAY command with address 00. 4. Send PLAY command. The device will start playback at address 00 and it will generate an interrupt when an EOM is reached. It will then stop playback. 6 Voice Solutions in Silicon™ ISD MicroTAD-16M SPI PORT The following diagram describes the SPI port and the control bits associated with it. Figure 3: SPI Port SPI CONTROL REGISTER The SPI control register provides control of individual device functions such as Play, Record, Message Cueing, Power-Up and Power-Down, Start and Stop operations, and Ignore Address pointers. Table 3: SPI Control Register Control Register Bit RUN Enable or Disable an operation = = 1 0 P/R 1 0 MC = = 1 0 Control Register Bit PU Start Stop Selects Play or Record operation = = ISD Device Function Master power control = = 1 0 IAB Play Record Device Function Power-Up Power-Down Ignore address control bit = = 1 0 Ignore input address register (A15–A0) Use the input address register contents for an operation (A15–A0) Enable or Disable Message Cueing P15–P0 Output of the row pointer register Enable Message Cueing Disable Message Cueing Input address register A15–A0 7 ISD MicroTAD-16M Figure 4: SPI Interface Simplified Block Diagram Table 4: Absolute Maximum Ratings (Packaged Parts)(1) Condition 150°C Storage temperature range –65°C to +150°C (V SS – 0.3 V) to (V CC + 0.3 V) Voltage applied to MOSI, SCLK, INT, RAC and SS pins (Input current limited to ±20mA) (V SS – 1.0 V) to 5.5V Lead temperature (soldering – 10 seconds) 300°C VCC – V SS –0.3 V to +7.0 V 1. 8 Operating Conditions (Packaged Parts) Condition Value Consumer operating temperature range 0°C to +50°C Supply voltage (VCC )(1) +2.85 V to +3.15 V Ground voltage (V SS) (2) 0V Value Junction temperature Voltage applied to any pin Table 5: 1. V CC = VCCA = VCCD. 2. V SS = VSSA = VSSD . Stresses above those listed may cause permanent damage to the device. Exposure to the absolute maximum ratings may affect device reliability. Functional operation is not implied at these conditions. Voice Solutions in Silicon™ ISD MicroTAD-16M Table 6: DC Parameters (Packaged Parts) Symbol Parameters Min(2) Typ(1) Max(2) VCC x 0.2 Units Conditions VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage 0.4 V IOL = 10 µA VOL1 RAC, INT Output Low Voltage 0.4 V IOL = 1 mA VOH Output High Voltage V IOH = –10 µA ICC VCC Current (Operating) — Playback — Record VCC x 0.8 V V VCC – 0.4 15 25 30 40 mA mA 1 10 µA ±1 µA 10 µA ISB VCC Current (Standby) IIL Input Leakage Current IHZ MISO Tristate Current REXT Output Load Impedance 5 RANA IN+ ANA IN+ Input Resistance 2.2 3.0 3.8 KΩ RANA IN– ANA IN– Input Resistance 40 56 71 KΩ AARP ANA IN+ or ANA IN– to AUD OUT Gain 1 REXT = ∞(3) REXT = ∞(3) (3) (4) KΩ 25 dB (5) 1. Typical values: TA = 25°C and 3.0 V. 2. All min/max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. 3. VCCA and VCCD connected together. 4. SS = VCCA = VCCD, XCLK = MOSI = VSSA= VSSD and all other pins floating. 5. Measured with AutoMute feature disabled. ISD 9 ISD MicroTAD-16M Table 7: AC Parameters (Packaged Parts) Symbol Characteristic Min(2) Typ(1) Max(2) Units Conditions FS Sampling Frequency 4.0 KHz (5) FCF Filter Pass Band 1.7 KHz 3-dB Roll-Off Point(3) (7) TREC Record Duration 16 min (6) TPLAY Playback Duration 16 min TPUD Power-Up Delay 50 msec TSTOP or TPAUSE Stop or Pause in Record or Play 100 msec TRAC RAC Clock Period 400 msec TRACLO RAC Clock Low Time 50 msec TRACM RAC Clock Period in Message Cueing Mode 250 µsec TRACML RAC Clock Low Time in Message Cueing Mode 31.25 µsec THD Total Harmonic Distortion VIN ANA IN Input Voltage 1 2 % 32 mV (9) @ 1 KHz Peak-to-Peak(4) (7) (8) 1. Typical values: TA = 25°C and 3.0 V. 2. All min/max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. 3. Low-frequency cut off depends upon the value of external capacitors (see Pin Descriptions). 4. Single-ended input mode. In the differential input mode, VIN maximum for ANA IN+ and ANA IN– is 16mVp-p. 5. For greater stability, an external clock can be utilized (see Pin Descriptions). 6. Filter specification applies to the antialiasing filter and the smoothing filter. Therefore, from input to output, expect a 6dB drop by nature of passing through both filters. 7. The typical output voltage will be approximately 570mVp-p with VIN at 32mVp-p. 8. For optimal signal quality, this maximum limit is recommended. 9. When a record command is sent, TRAC = TRAC + TRACLO on the first row addressed. 10 Voice Solutions in Silicon™ ISD MicroTAD-16M Table 8: Absolute Maximum Ratings (Die)(1) Condition Table 9: Condition Value Consumer operating temperature range (1) 0°C to +50°C Supply voltage (V CC)(2) +2.85 V to +3.15 V Ground voltage (VSS)(3) 0V Value Junction temperature 150°C Storage temperature range –65°C to +150°C Voltage applied to any pad (VSS – 0.3 V) to (VCC + 0.3 V) Voltage applied to MOSI, SCLK, INT, (VSS – 1.0 V) to RAC and SS pins 5.5V (Input current limited to ±20mA) 1. Case temp 2. V CC = V CCA = V CCD V SS = VSSA = VSSD. 3. V CC – V SS 1. Operating Conditions (Die) –0.3 V to +7.0 V Stresses above those listed may cause permanent damage to the device. Exposure to the absolute maximum ratings may affect device reliability. Functional operation is not implied at these conditions. Table 10: DC Parameters (Die) Symbol Parameters Min (2) Typ (1) Max(2) VCC x0.2 Units Conditions VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage 0.4 V IOL = 10 µA VOL1 RAC, INT Output Low Voltage 0.4 V IOL = 1 mA VOH Output High Voltage V IOH = –10 µA ICC VCC Current (Operating) — Playback — Record VCC x 0 . 8 V V VCC – 0 . 4 15 25 30 40 mA mA 1 10 µA ±1 µA 10 µA REXT = ∞ (3) REXT = ∞ (3) (3) (4) ISB VCC Current (Standby) IIL Input Leakage Current IHZ MISO Tristate Current REXT Output Load Impedance 5 RANA IN+ ANA IN+ Input Resistance 2.2 3.0 3.8 KΩ RANA IN– ANA IN– Input Resistance 40 56 71 KΩ AARP ANA IN+ or ANA IN– to AUDOUT Gain 1 KΩ 25 dB (5) 1. Typical values: T A = 25°C and 3.0 V. 2. All min/max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. 3. V C C A and VCCD connected together. 4. SS = V C C A= VCCD , XCLK = MOSI = V SSA = V SSD and all other pins floating. 5. Measured with AutoMute feature disabled. ISD 11 ISD MicroTAD-16M Table 11: AC Parameters (Die) Symbol Characteristic Min(2) Typ(1) Max(2) Units Conditions FS Sampling Frequency 4.0 KHz (5) FCF Filter Pass Band 1.7 KHz 3dB Roll-Off Point (3) (6) TREC Record Duration 16 min (5) TPLAY Playback Duration 16 min (5) TPUD Power-Up Delay 50 msec TSTOP or TPAUSE Stop or Pause in Record or Play 100 msec TRAC RAC Clock Period 400 msec TRACLO RAC Clock Low Time 50 msec TRACM RAC Clock Period in Message Cueing Mode 250 µsec TRACML RAC Clock Low Time in Message Cueing Mode 31.25 µsec THD Total Harmonic Distortion VIN ANA IN Input Voltage 1 2 % 32 mV (9) @ 1 KHz Peak-to-Peak(4) (7) (8) 1. Typical values: TA = 25°C and 3.0 V. 2. All min/max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. 3. Low-frequency cut off depends upon the value of external capacitors (see Pin Descriptions). 4. Single-ended input mode. In the differential input mode, VIN maximum for ANA IN+ and ANA IN– is 16 mV peakto-peak. 5. For greater stability, an external clock can be utilized (see Pin Descriptions). 6. Filter specification applies to the antialiasing filter and to the smoothing filter. 7. The typical output voltage will be approximately 570 mV peak-to-peak with VIN at 32 mV peak-to-peak. 8. For optimal signal quality, this maximum limit is recommended. 9. When a record command is sent, TRAC = TRAC + TRACLO on the first row addressed. 12 Voice Solutions in Silicon™ ISD MicroTAD-16M Table 12: SPI AC Parameters1 Symbol Characteristics Min Max Units TSSS SS Setup Time 500 nsec TSSH SS Hold Time 500 nsec TDIS Data in Setup Time 200 nsec TDIH Data in Hold Time 200 nsec TPD Output Delay 500 nsec TDF(2) Output Delay to hiΖ 500 nsec TSSmin SS HIGH TSCKhi 1 µsec SCLK High Time 400 nsec TSCKlow SCLK Low Time 400 nsec F0 CLK Frequency 1,000 1. Typical values: TA= 25°C and 3.0 V. Timing measured at 50 percent of the VCC level. 2. Tristate test condition. ISD Conditions KHz 13 ISD MicroTAD-16M TIMING DIAGRAMS Figure 5: Timing Diagram Figure 6: 8-Bit Command Format 14 Voice Solutions in Silicon™ ISD MicroTAD-16M Figure 7: 24-Bit Command Format Figure 8: Playback/Record and Stop Cycle ISD 15 ISD MicroTAD-16M Figure 9: Application Example Using SPI(1) 16 1. This application example is for illustration purposes only. ISD makes no representation or warranty that such application will be suitable for production. 2. Please make sure the bypass capacitor, C2 is as close as possible to the package. Voice Solutions in Silicon™ ISD MicroTAD-16M Figure 10: Application Example Using Microwire(1) 1. This application example is for illustration purposes only. ISD makes no representation or warranty that such application will be suitable for production. 2. Please make sure the bypass capacitor, C2 is as close as possible to the package. Figure 11: Application Example Using SPI Port on Microcontroller(1) 1. This application example is for illustration purposes only. ISD makes no representation or warranty that such application will be suitable for production. 2. Please make sure the bypass capacitor, C2 is as close as possible to the package. ISD 17 ISD MicroTAD-16M DEVICE PHYSICAL DIMENSIONS Figure 12: 28-Lead 8x13.4 mm Plastic Thin Small Outline Package (TSOP) Type I (E) Table 13: Plastic Thin Small Outline Package (TSOP) Type I (E) Dimensions INCHES Min Nom Max Min Nom Max A 0.520 0.528 0.535 13.20 13.40 13.60 B 0.461 0.465 0.469 11.70 11.80 11.90 C 0.311 0.315 0.319 7.90 8.00 8.10 D 0.002 0.006 0.05 E 0.007 0.011 0.17 F 0.009 0.0217 0.15 0.22 0.27 0.55 G 0.037 0.039 0.041 0.95 1.00 1.05 H 0° 3° 6° 0° 3° 6° I 0.020 0.022 0.028 0.50 0.55 0.70 J 0.004 0.008 0.10 NOTE: 18 MILLIMETERS 0.21 Lead coplanarity to be within 0.004 inches. Voice Solutions in Silicon™ ISD MicroTAD-16M Figure 13: 28-Lead 0.600-Inch Plastic Dual Inline Package (PDIP) (P) Table 14: Plastic Dual Inline Package (PDIP) (P) Dimensions INCHES A MILLIMETERS Min Nom Max Min Nom Max 1.445 1.450 1.455 36.70 36.83 36.96 B1 0.150 B2 0.065 C1 0.600 C2 0.530 0.070 0.540 D 3.81 0.075 1.65 0.625 15.24 0.550 13.46 1.78 15.88 13.72 0.19 D1 0.015 E 0.125 F 0.015 G 0.055 H 1.91 13.97 4.83 0.38 0.135 3.18 0.018 0.022 0.38 0.46 0.56 0.060 0.065 1.40 1.52 1.65 0.100 3.43 2.54 J 0.008 0.010 0.012 0.20 0.25 0.30 S 0.070 0.075 0.080 1.78 1.91 2.03 q 0° 15° 0° ISD 15° 19 ISD MicroTAD-16M Figure 14: 28-Lead 0.300-Inch Plastic Small Outline Integrated Circuit (SOIC) (S) Table 15: Plastic Small Outline Integrated Circuit (SOIC) (S) Dimensions INCHES Min Nom Max Min Nom Max A 0.701 0.706 0.711 17.81 17.93 18.06 B 0.097 0.101 0.104 2.46 2.56 2.64 C 0.292 0.296 0.299 7.42 7.52 7.59 D 0.005 0.009 0.0115 0.127 0.22 0.29 E 0.014 0.016 0.019 0.35 0.41 0.48 F 0.050 1.27 G 0.400 0.406 0.410 10.16 10.31 10.41 H 0.024 0.032 0.040 0.61 0.81 1.02 NOTE: 20 MILLIMETERS Lead coplanarity to be within 0.004 inches. Voice Solutions in Silicon™ ISD MicroTAD-16M Figure 15: ISD MicroTAD-16M Bonding Physical Layout1 (Unpackaged Die) MOSI SCLK VCCD2 INT ISD MicroTAD-16M VSSD2 I. Die Dimensions X: 4230 microns Y: 9780 microns II. Die Thickness(3) 11.5 ±0.5 mils MISO SS VCCD1 XCLK RAC VSSA VSSD1 III. Pad Opening (min) 90 x 90 microns 3.5 x 3.5 mils ISD MicroTAD-16M VSSA(2) VSSA AUD OUT AM CAP ANA IN– VCCA(2) ANA IN+ 1. The backside of die is internally connected to VSS. It MUST NOT be connected to any other potential or damage may occur. 2. Double bond recommended. 3. This figure reflects the current die thickness. Please contact ISD as this thickness may change in the future. ISD 21 ISD MicroTAD-16M Table 16: ISD MicroTAD-16M Device Pin/Pad Designations, with Respect to Die Center (µm) Pin X Axis Y Axis VSSA VSS Analog Power Supply –1898.1 –4622.4 VSSA VSS Analog Power Supply –1599.9 –4622.4 AUD OUT Audio Output 281.9 –4622.4 AM CAP AutoMute 577.3 –4622.4 ANA IN – Inverting Analog Input 1449.4 –4622.4 ANA IN + Noninverting Analog Input 1603.5 –4622.4 VCCA(1) VCC Analog Power Supply 1898.7 –4622.4 VSSA VSS Analog Power Supply 1885.2 –4622.4 RAC Row Address Clock 1483.8 4623.7 INT Interrupt 794.8 4623.7 XCLK External Clock Input 564.8 4623.7 VCCD2 VCC Digital Power Supply 387.9 4623.7 VCCD1 VCC Digital Power Supply 169.5 4623.7 SCLK Slave Clock –14.7 4623.7 SS Slave Select –198.1 4623.7 MOSI Master Out Slave In –1063.7 4623.7 MISO Master In Slave Out –1325.6 4623.7 VSSD1 VSS Digital Power Supply –1655.3 4623.7 VSSD2 VSS Digital Power Supply –1836.9 4623.7 1. 22 Pin Name Double bond recommended. Voice Solutions in Silicon™ ISD MicroTAD-16M ORDERING INFORMATION ISD Part Number Description ISD MicroTAD 16M Product Family ISD MicroTADTM Duration: 16M=16 minutes Special Temperature Field: Blank= Consumer Packaged (0°C to +50°C) or Consumer Die (0°C to +50°C) Package Type: E = 28-Lead 8x13.4mm Plastic Thin Small Outline Package (TSOP) Type 1 P = 28-Lead 0.600-Inch Plastic Dual Inline Package (PDIP) S = X = 28-Lead 0.300-Inch Plastic Small Outline Package (SOIC) Die When ordering ISD MicroTADTM devices, please refer to the following valid part numbers. Part Number ISD MicroTAD-16ME ISD MicroTAD-16MP ISD MicroTAD-16MS ISD MicroTAD-16MX For the latest product information, access ISD’s worldwide website at http://www.isd.com. ISD 23 IMPORTANT NOTICES The warranty for each product of ISD (Information Storage Devices, Inc.), is contained in a written warranty which governs sale and use of such product. Such warranty is contained in the printed terms and conditions under which such product is sold, or in a separate written warranty supplied with the product. Please refer to such written warranty with respect to its applicability to certain applications of such product. These products may be subject to restrictions on use. Please contact ISD, for a list of the current additional restrictions on these products. By purchasing these products, the purchaser of these products agrees to comply with such use restrictions. Please contact ISD for clarification of any restrictions described herein. ISD, reserves the right, without further notice, to change the ISD ChipCorder product specifications and/or information in this document and to improve reliability, functions and design. The 100-year retention and 100K record cycle projections are based upon accelerated reliability tests, as published in the ISD Reliability Report, and are neither warranted nor guaranteed by ISD. This data sheet and any future addendum to this data sheet is (are) the complete and controlling ISD ChipCorder product specifications. In the event any inconsistencies exist between the information in this and other product documentation, or in the event that other product documentation contains information in addition to the information in this, the information contained herein supersedes and governs such other information in its entirety. Copyright© 1999, ISD (Information Storage Devices, Inc.) All rights reserved. ISD is a registered trademark of ISD. ChipCorder and MicroTAD are trademarks of ISD. All other trademarks are properties of their respective owners. ISD assumes no responsibility or liability for any use of the ISD ChipCorder products. ISD conveys no license or title, either expressed or implied, under any patent, copyright, or mask work right to the ISD ChipCorder products, and ISD makes no warranties or representations that the ISD ChipCorder products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application examples and alternative uses of any integrated circuit contained in this publication are for illustration purposes only and ISD makes no representation or warranty that such applications shall be suitable for the use specified. 2727 North First Street San Jose, California 95134 800/677-0769 (US Only) Tel: 408/943-6666 Fax: 408/544-1787 http://www.isd.com Part No. ISDMicroTADDS1-599