ER1600F THRU ER1604F ISOLATION SUPERFAST RECOVERY RECTIFIERS VOLTAGE - 50 to 400 Volts CURRENT - 16.0 Amperes FEATURES l Plastic package has Underwriters Laboratory ITO-220AB Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound l l Exceeds environmental standards of MIL-S-19500/228 Low power loss, high efficiency l l Low forward voltage, high current capability High surge capacity l l Super fast recovery times, high voltage Dual Rectifier (Epitaxial chip) construction MECHANICAL DATA Case: ITO-220AB full molded plastic package Terminals: Leads, solderable per MIL-STD-202, Method 208 Polarity: As marked Mounting Position: Any Weight: 0.08 ounces, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ¢J ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20%. Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC=90 ¢J ER1600F ER1601F ER1601AF ER1602F ER1603F ER1604F 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 320 400 Peak Forward Surge Current, 8.3ms single half sine-wave superimposed on rated load(JEDEC method) Maximum Forward Voltage at 8.0A per element Maximum DC Reverse Current at Ta=25 ¢J 16.0 V A 125 A 0.95 DC Blocking Voltage per element Ta=125 ¢J Typical Junction capacitance (Note 1) Maximum Reverse Recovery Time(Note 2) Typical Thermal Resistance(Note 3) R £KJC Operating and Storage Temperature Range TJ NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC 2. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A 3. Thermal resistance junction to CASE UNITS V V 1.30 £g A 10 500 62 35 PF 50 3.0 -55 to +150 V ns ¢J /W ¢J RATING AND CHARACTERISTIC CURVES INSTANTANEOUS FORWARD CURRENT AMPERES AVERAGE FORWARD CURRENT, AMPERES ER1600F THRU ER1604F 20 16 12 8.0 4.0 0 0 50 100 40 20 50. 100. 150. 200V 10 8 6 4 2 300. 400V 1.0 .8 . .6 .4 TJ = 25 ¢J PULSE WIDTH = 200£gs .2 .1 .6 150 .7 .8 9 1.0 1.1 1.2 1.3 INSTANTANEOUS FORWARD CHARACTERISTIC Fig. 1-FORWARD CURRENT DERATING CURVE Fig. 2-TYPICAL INSTNATANEOUS FORWARD CHARACTERISTIC 1000 TC = 100 ¢J 100 TC = 75¢J 10 TC = 25¢J 1 .01 0 100 200 300 PEAK FORWARD SURGE CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MILLAMPERES CASE TEMPERATURE, ¢J 135 120 105 90 75 8.3ms SINGLE HALF SINE WAVE JEDEC METHOD 60 45 30 15 1 2 5 10 20 50 100 NO. OF CYCLES AT 60Hz Fig. 4-MAXIMUM NON-REPETITIVE SURGE CURRENT . 80 CAPACITANCE, pF Fig. 3-TYPICAL REVERSE CHARACTERISTICS 70 60 TJ = 25 ¢J 50 40 30 1 2 5 20 50 100 500 REVERSE VOLTAGE, VOLTS Fig. 5-TYPICAL JUNCTION CAPACITANCE