R15 Redimount Regulator G3/4 to G11/2 Olympian ● Olympian plug-in design ● Robust and compact ● High flow unit with large valve and diaphragm ● Adjusting Knob has Snap-Action Lock ● Excellent flow and regulation characteristics Technical Data Medium: Compressed air only Maximum Inlet Pressure: 20 bar Operating Temperature: –20˚C* to +80˚C *Consult our Technical Service for use below +2˚C Recommended Regulated Pressures††: 0,4 - 8 bar standard 0 - 4 bar optional 2 - 16 bar optional (only available with T-bar adjusting screw) Port Sizes G3/4, G1, G11/4,G11/2 to ISO 1179 Accepts ISO 228 (BS 2779) parallel or ISO 7 (BS 21) taper connectors †† Can be adjusted to zero bar outlet pressure and, generally, to pressures in excess of those specified. Gauge Ports: G1/8 Maximum Flow with 10 bar inlet pressure, 6,3 bar outlet pressure and pressure drop of 1 bar: 180 dm3/s Alternative Models Other port thread forms T-bar adjusting screw Maximum pressure setting stop Key Lock adjusting knob Materials Aluminium alloy body. Acetal resin adjusting knob (steel T-bar adjusting screw). Synthetic rubber elastomeric materials. 1 2 Ordering Information To order a standard Redimount Regulator, quote model number from table overleaf. For non-standard models substitute appropriate digits as instructed. 1/90 8.6.041.01 R15 Typical Performance Characteristics Standard Redimount Regulators 8 bar spring Port Size G3/4 G1 G11/4 G11/2 Relieving R15-600-RNLD R15-800-RNLD R15-A00-RNLD R15-B00-RNLD Weight kg 2,04 2,04 2,08 2,12 Non-relieving R15-600-NNLD R15-800-NNLD R15-A00-NNLD R15-B00-NNLD Weight kg 2,14 2,09 2,11 2,15 Non-standard Models For replacement Regulators substitute ‘0’ and ‘O’ at the 4th and 10th digits respectively, e.g. R15-000-RNLO. Supplied without Unidaptors as replacement units or for the build-up of Combination Units. Please consult our Technical Service for further details. For optional 4 or 16 bar springs, substitute ‘F’ or ‘S’ respectively for ‘L’ at the 9th digit, e.g. R15-600-RNFD.(16 bar spring only available with T-bar adjusting screw). For optional T-bar adjusting screw, substitute ‘1’ for ‘0’ at the 6th digit, e.g. R15-601-RNLD. Specify if unit is required complete with T15 Shut-Off Valve fitted upstream. For details of Shut-Off Valves see page 8.11.021.01. For other options, please consult our Technical Service. Accessories Wall Mounting Bracket Kit, see page 8.6.041.03. Pressure Gauges, see page 8.11.031.01. 8.6.041.02 R15 Redimount Regulator G3/4 G1 G11/4 G11/2 Non-relieving R15-600-NNLD R15-800-NNLD R15-A00-NNLD R15-B00-NNLD G3/4 G1 G11/4 G11/2 222* 198 60 Relieving R15-600-RNLD R15-800-RNLD R15-A00-RNLD R15-B00-RNLD G 1/8 54 B 112 100 50 190 (200 G11/4, G11/2 ) *Minimum clearance required to remove unit from yoke. Bracket Mounting Bracket Kit reference: G3/4 G1 G11/4 G11/2 208* 18-001-979 18-001-979 18-001-978 N/A 50 100 8,5 190* 72 15 *If Shut-Off Valve fitted add 46 mm to dimensions. 1/90 8.6.041.03 R15 Spares Kits Type Relieving Non-relieving Gasket Kit R15-GK R15-GK Repair Kit R15-100R R15-100N Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN MARTONAIR. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. 8.6.041.04