MIM-0KM1xKF INFRARED RECEIVER MODULE Description The MIM-0KM1xKF is miniaturized infrared receivers for remote control and other applications requiring improved ambient light rejection. The separate PIN diode and preamplifier IC are assembled on a single leadframe. The epoxy package contains a special IR filter. This module has excellent performance even in disturbed ambient light applications and provides protection against uncontrolled output pulses. Features * Photo detector and preamplifier in one package * Internal filter for PCM frequency * High immunity against ambient light * Improved shielding against electric field disturbance * 3.0-Volt supply voltage; low power consumption * TTL and CMOS compatibility MIM-0KM1xKF Series Models l MIM-0KM1AKF 37.9KHz l MIM-0KM1BKF 32.7KHz l MIM-0KM1CKF 40.0 KHz l MIM-0KM1DKF 36.7KHz l MIM-0KM1FKF 56.7 KHz Unit : mm BLOCK DIAGRAM VS TRAP ABLC BPF TRIMMING Output fo GND REV: A1 Unity Opto Technology Co., Ltd. 07/08/2003 MIM-0KM1xKF Absolute Maximum Ratings Item o @ Ta=25 C Symbol Ratings Unit Supply voltage VCC 5.8 V Operating temperature Topr -10 ~ + 60 o C -20 ~ + 75 o C 260 o C Tstg Storage temperature Tsd Soldering temperature Remark t<=10 s, 1mm from case Electro-optical characteristics (Vcc=3.0V) Parameter Symbol Min. Typ. Max. Unit Current consumption Icc 1.0 1.6 mA Response wavelength Tuning frequency λp f0 940 32.7,36.7,37.9,40.0,56.7 nm KHZ Remarks Under no signal - - - - - active low output - - - - - Output form H level output voltage V0 h L level output voltage V0 l H level output pulse width Twh L level output pulse width 2.3 V 0.5 V 400 800 µs Twl 400 800 µs Distance between emitter & detector L1 10.0 Half angle ∆θ ±45 Test Method A. Standard Transmitter m Note 1 deg Horizonal direction 25cm PD3516 ON/OFF pulse width satisfied from 25 cm to detection limit 600µs carrier frequency f0 duty 50% 600µs 10k Transmitter Duty 50% +3.0V 10kΩ 10µF Vout 600µs GND Oscilloscope Fig 1. Burst Wave Fig 2. Standard Transmitter Measurement circuit B. Detection Length Test Transmitter output θ θ Vout D.U.T θ: indicates horizontal and vertical directions L REV: A1 Unity Opto Technology Co., Ltd. 07/08/2003 MIM-0KM1xKF C . Pulse Width Test Transmitter output 600µs 600µs DUT output pulse Twl Twh V0h V0l Application Circuit 100Ω*) 3 4.7µF *) MIM-0KM1xKF MIE-544A2 Vcc (+3V) >10kΩ optional µC 1 2 GND *) recommended to suppress power supply disturbances CHARACTERISTIC CURVES (TA=25oC) Output Pulse Width tPW(µs) Supply Current Icc (mA). 900 1.4 1.2 1.0 0.8 0.6 800 Burst length * 600µs, cycle = 1.2ms tpw: Average value of output from start of signal input to 60th pulse 700 600 500 Input Level VIN (mVP-P) 2 3 4 5 6 7 8 400 0.1 10 100 1000 Input Level (mVp-p) Supply Voltage Vcc (V) SUPPLY VOLTAGE vs. SUPPLY CURRENT 1 INPUT LEVEL vs.OUTPUT PULSE WIDTH NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies the standard under the conditions below against the standerd transmitter. (1)Measuring place ………Indoor without extreme reflection of light. (2)Ambient light source… Detecting surface illumination shall be 200±50Lux under ordinary hite fluorescense lamp of no high frequency lighting. (3)Standard transmitter … Burst wave indicated in Fig 1. of standard transmitter shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2. REV: A1 Unity Opto Technology Co., Ltd. 07/08/2003 MIM-0KM1xKF Reliability Test item High temparature High temp. & high humi. Low temparature Heat cycle Dropping Test condition Ta=+60oC Vcc=5.0 V t=240H o Ta=+40 C 90%RH Vcc=5.0V t=240H Ta= -10oC Vcc=5.0V t=240H -20oC(0.5H) ~ +75oC(0.5H) 20cycle Test devices shall be dropped 3 times naturally onto hard wooden board from a 75cm height position. Standard Note 2. Note 2. Note 2. Note 2. Note 3. NOTE 2. (electro-optical charactistics) shall be satisfied after leaving 2 hours in the normal temperature . NOTE 3. (electro-optical charactistics) shall be satisfied and no conoid deforms and destructions of appearance .(excepting deforms of terminals) Inspection standard 1.Among electrical characteristics , total number shall be inspected on items blow. 1-1 front distance between emitter & detector 1-2 Current consumption 1-3 H level output voltage 1-4 L level output voltage 2.Items except above mentioned are not inspected particularly , but shall fully satisfy CAUTION ( When use and storage of this device ) 1.Store and use where there is no force causing transformation or change in quality . 2.Store and use where there is no corrosive gas or sea(salt) breeze . 3.Store and use where there is no extreme humidity . 4.Solder the lead-pin within the condition of ratings. After soldering do not add extra force . 5.Do not wash this device . Wipe the stains of diode side with a soft cloth. You can use the solvent , ethylalcohol or methylalcohol or isupropylene only . 6.To prevent static electricity damage to the Pre-AMP make sure that the human body , the soldering iron is connected to ground before using . 7.Put decoupling device between Vcc and GND for reduse the noise from power supply line . 8.The performance of remote-control system depends on environments condition and ability of periferal parts. Customer should evaluate the performance as total system in those conditions after system up with components such as commander , micon and this receiver module . Guarantee period and scope 1.Guarantee period One year after delivery to desired place . 2.Guarantee scope A re-delivery of goods will be carried out if the cause of malfunction lies in our device .However no responsibilities be taken for the inconveniences caused by the malfunction of our devices . Others 1.This device is not design to endure radiative rays and heavily charged particles . 2.In case where any trouble or questions arise,both parties agress to make full discussion covering the said problem . REV: A1 Unity Opto Technology Co., Ltd. 07/08/2003