ADS7834 ® ADS 783 4 For most current data sheet and other product information, visit www.burr-brown.com 12-Bit High Speed Low Power Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION ● 500kHz THROUGHPUT RATE The ADS7834 is a 12-bit sampling analog-to-digital converter (A/D) complete with sample/hold, internal 2.5V reference, and synchronous serial interface. Typical power dissipation is 11mW at a 500kHz throughput rate. The device can be placed into a power-down mode which reduces dissipation to just 2.5mW. The input range is zero to the reference voltage, and the internal reference can be overdriven by an external voltage. ● 2.5V INTERNAL REFERENCE ● LOW POWER: 11mW ● SINGLE SUPPLY +5V OPERATION ● DIFFERENTIAL INPUT ● SERIAL INTERFACE ● GUARANTEED NO MISSING CODES ● MINI-DIP-8 AND MSOP-8 ● 0V TO VREF INPUT RANGE Low power, small size, and high-speed make the ADS7834 ideal for battery operated systems such as wireless communication devices, portable multi-channel data loggers, and spectrum analyzers. The serial interface also provides low-cost isolation for remote data acquisition. The ADS7834 is available in a plastic mini-DIP-8 or an MSOP-8 package and is guaranteed over the –40°C to +85°C temperature range. APPLICATIONS ● BATTERY OPERATED SYSTEMS ● DIGITAL SIGNAL PROCESSING ● HIGH SPEED DATA ACQUISITION ● WIRELESS COMMUNICATION SYSTEMS CLK SAR CONV +In Serial Interface CDAC –In Comparator S/H Amp Internal +2.5V Ref Buffer VREF DATA 10kΩ ±30% International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1998 Burr-Brown Corporation SBAS098 PDS-1457B 1 Printed in U.S.A. May, 2000 ADS7834 SPECIFICATIONS At TA = –40°C to +85°C, +VCC = +5V, fSAMPLE = 500kHz, fCLK = 16 • fSAMPLE, internal reference, unless otherwise specified. ADS7834P, E PARAMETER ANALOG INPUT Full-Scale Input Span(1) Absolute Input Range CONDITIONS MIN +IN – (–IN) +IN –IN 0 –0.2 –0.2 Capacitance Leakage Current TYP ADS7834PB, EB MAX MIN VREF VREF +0.2 +0.2 ✻ ✻ ✻ Common-Mode Rejection Noise Power Supply Rejection DYNAMIC CHARACTERISTICS Signal-to-Noise Ratio Total Harmonic Distortion(4) Signal-to-(Noise+Distortion) Spurious Free Dynamic Range Usable Bandwidth REFERENCE OUTPUT Voltage Source Current(5) Drift Line Regulation REFERENCE INPUT Range Resistance(6) DIGITAL INPUT/OUTPUT Logic Family Logic Levels: VIH VIL VOH VOL Data Format POWER SUPPLY REQUIREMENT +VCC Quiescent Current Power Dissipation TEMPERATURE RANGE Specified Performance ±2 70 50 60 1.2 ✻ ✻ ✻ ✻ ✻ ✻ ✻ µs µs kHz ns ps ns ✻ 500 IOUT = 0 Static Load IOUT = 0 4.75V ≤ VCC ≤ 5.25V 68 72 2.475 72 –78 70 78 350 2.50 –72 70 75 2.525 50 2.48 2.0 2.55 10 ✻ ✻ 3.0 –0.3 3.5 VCC +0.3 0.8 0.4 4.75 –40 dB dB dB dB kHz 2.52 ✻ V µA ppm /°C mV ✻ ✻ V kΩ ✻ ✻ ✻ ✻ V V V V ✻ V mA mA mW mW ✻ 5.25 2.2 0.5 11 2.5 ✻ ✻ ✻ ✻ ✻ Straight Binary Specified Performance fSAMPLE = 500kHz Power-Down fSAMPLE = 500kHz Power-Down ✻ –75 ✻ CMOS |IIH| ≤ +5µA |IIL| ≤ +5µA IOH = –500µA IOL = 500µA ✻ –82 72 82 ✻ ✻ ✻ 20 0.6 to Internal Reference Voltage ±1 ±1 ✻ ±15 ±35 ✻ ✻ 5 30 350 = 5Vp-p at 10kHz = 5Vp-p at 10kHz = 5Vp-p at 10kHz = 5Vp-p at 10kHz SNR > 68dB V V V pF µA Bits Bits LSB(2) LSB LSB LSB LSB dB dB µVrms LSB ±0.5 ±0.5 ±1 ±7 ±5 ±30 ±50 1.625 0.350 VIN VIN VIN VIN ✻ ✻ ✻ ✻ ±1 ±0.8 ±2 ±12 Worst Case ∆, +VCC = 5V ±5% SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Aperture Delay Aperture Jitter Step Response UNITS ✻ 12 12 25°C –40°C to +85°C DC, 0.2Vp-p 1MHz, 0.2Vp-p MAX ✻ ✻ 25 1 SYSTEM PERFORMANCE Resolution No Missing Codes Integral Linearity Error Differential Linearity Error Offset Error Gain Error(3) TYP ✻ ✻ ✻ ✻ ✻ 20 +85 ✻ ✻ ✻ °C ✻ Specifications same as ADS7834P,E. NOTES: (1) Ideal input span, does not include gain or offset error. (2) LSB means Least Significant Bit, with VREF equal to +2.5V, one LSB is 610µV. (3) Measured relative to an ideal, full-scale input (+IN – (–IN)) of 2.499V. Thus, gain error includes the error of the internal voltage reference. (4) Calculated on the first nine harmonics of the input frequency. (5) If the internal reference is required to source current to an external load, the reference voltage will change due to the internal 10kΩ resistor. (6) Can vary ±30%. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® ADS7834 2 ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY +VCC to GND ............................................................................ –0.3V to 6V Analog Inputs to GND .............................................. –0.3V to (VCC + 0.3V) Digital Inputs to GND ............................................... –0.3V to (VCC + 0.3V) Power Dissipation .......................................................................... 325mW Maximum Junction Temperature ................................................... +150°C Operating Temperature Range ......................................... –40°C to +85°C Storage Temperature Range .......................................... –65°C to +150°C Lead Temperature (soldering, 10s) ............................................... +300°C Electrostatic discharge can cause damage ranging from performance degradation to complete device failure. BurrBrown Corporation recommends that all integrated circuits be handled and stored using appropriate ESD protection methods. NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet published specifications. PIN CONFIGURATION Top View VREF 1 +IN 2 8 +VCC VREF 1 7 CLK +IN 2 ADS7834 8 +VCC 7 CLK ADS7834 –IN 3 6 DATA –IN 3 6 DATA GND 4 5 CONV GND 4 5 CONV Plastic Mini-DIP-8 MSOP-8 PIN ASSIGNMENTS PIN NAME DESCRIPTION 1 VREF Reference Output. Decouple to ground with a 0.1µF ceramic capacitor and a 2.2µF tantalum capacitor. 2 +IN Non-Inverting Input. 3 –IN Inverting Input. Connect to ground or to remote ground sense point. 4 GND 5 CONV Convert Input. Controls the sample/hold mode, start of conversion, start of serial data transfer, type of serial transfer, and power down mode. See the Digital Interface section for more information. 6 DATA Serial Data Output. The 12-bit conversion result is serially transmitted most significant bit first with each bit valid on the rising edge of CLK. By properly controlling the CONV input, it is possibly to have the data transmitted least significant bit first. See the Digital Interface section for more information. Ground. 7 CLK Clock Input. Synchronizes the serial data transfer and determines conversion speed. 8 +VCC Power Supply. Decouple to ground with a 0.1µF ceramic capacitor and a 10µF tantalum capacitor. PACKAGE/ORDERING INFORMATION PRODUCT ADS7834E ADS7834E ADS7834EB ADS7834EB ADS7834P ADS7834PB MAXIMUM INTEGRAL LINEARITY ERROR (LSB) MAXIMUM DIFFERENTIAL LINEARITY ERROR (LSB) ±2 " PACKAGE PACKAGE DRAWING NUMBER(1) SPECIFICATION TEMPERATURE RANGE PACKAGE MARKING(2) ORDERING NUMBER(3) TRANSPORT MEDIA N/S(4) MSOP-8 337 –40°C to +85°C C34 " " " " " C34 ADS7834E/250 ADS7834E/2K5 ADS7834EB/250 ADS7834EB/2K5 ADS7834P ADS7834PB Tape and Reel Tape and Reel Tape and Reel Tape and Reel Rails Rails ±1 ±1 MSOP-8 337 –40°C to +85°C " " " " " " N/S(4) ±1 Plastic DIP-8 006 –40°C to +85°C " " " ADS7834P ADS7834PB ±2 ±1 NOTE: (1) For detail drawing and dimension table, please see end of data sheet or Package Drawing File on Web. (2) Performance Grade information is marked on the reel. (3) Models with a slash(/) are available only in Tape and reel in quantities indicated (e.g. /250 indicates 250 units per reel, /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of ”ADS7834E/2K5“ will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to the www.burr-brown.com web site under Applications and Tape and Reel Orientation and Dimensions. (4) N/S = Not Specified, typical only. However, 12-Bits no missing codes is guaranteed over temperature. ® 3 ADS7834 TYPICAL PERFORMANCE CURVES At TA = +25°C, VCC = +5V, fSAMPLE = 500kHz, fCLK = 16 • fSAMPLE, and internal +2.5V reference, unless otherwise specified. OFFSET VOLTAGE vs TEMPERATURE 0.5 0 0.4 –1 Delta from +25°C (LSB) Delta from +25°C (LSB) FULL-SCALE ERROR vs TEMPERATURE 1 –2 –3 –4 –5 –6 0.3 0.2 0.1 0 –0.1 –0.2 –7 –8 –0.3 –40 –20 0 20 40 60 80 100 –40 –20 0 Temperature (°C) 40 60 80 100 SUPPLY CURRENT vs TEMPERATURE 470 2.3 460 2.2 450 Supply Current (mA) Power-down Supply Current (µA) POWER-DOWN SUPPLY CURRENT vs TEMPERATURE 440 430 420 410 2.1 fSAMPLE = 500kHz 2.0 1.9 1.8 fSAMPLE = 125kHz 1.7 400 390 –40 –20 0 20 40 60 80 1.6 –40 100 –20 Temperature (°C) 0 20 40 60 100 80 Temperature (°C) INTEGRAL LINEARITY and DIFFERENTIAL LINEARITY vs SAMPLE RATE SUPPLY CURRENT vs SAMPLE RATE 2.4 Delta from fSAMPLE = 500kHz (LSB) 0.06 2.3 Supply Current (mA) 20 Temperature (°C) 2.2 2.1 2.0 1.9 1.8 0.04 0.02 Change in Integral Linearity (LSB) 0 –0.02 –0.04 Change in Differential Linearity (LSB) –0.06 –0.08 –0.1 1.7 100 200 300 400 500 100 600 300 400 Sample Rate (kHz) Sample Rate (kHz) ® ADS7834 200 4 500 600 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VCC = +5V, fSAMPLE = 500kHz, fCLK = 16 • fSAMPLE, and internal +2.5V reference, unless otherwise specified. OFFSET VOLTAGE vs EXTERNAL REFERENCE VOLTAGE 0.300 0.2 0.200 0.1 Delta from VREF = 2.5V (mV) Delta from VREF = 2.5V (mV) FULL-SCALE ERROR vs EXTERNAL REFERENCE VOLTAGE 0.100 0.000 –0.100 –0.200 –0.300 –0.400 –0.500 0 –0.1 –0.2 –0.3 –0.4 –0.5 –0.6 –0.7 –0.600 –0.8 2.0 2.1 2.2 2.3 2.4 2.5 2.0 2.2 External Reference Voltage (V) PEAK-TO-PEAK NOISE vs EXTERNAL REFERENCE VOLTAGE 30 Power Supply Rejection (mV/V) 0.85 Peak-to-Peak Noise (LSB) 2.55 POWER SUPPLY REJECTION vs POWER SUPPLY RIPPLE FREQUENCY 0.90 0.80 0.75 0/70 0.65 0.60 0.55 0.50 25 20 15 10 5 0 2 2.1 2.2 2.3 2.4 2.5 1 10 100 10k 1k 100k 1M Power Supply Ripple Frequency (Hz) External Reference Voltage (V) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 977Hz, –0.2dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.77kHz, –0.2dB) 0 0 –20 –20 Amplitude (dB) Amplitude (dB) 2.4 External Reference Voltage (V) –40 –60 –80 –100 –40 –60 –80 –100 –120 –120 0 50 100 150 200 250 0 Frequency (kHz) 50 100 150 200 250 Frequency (kHz) ® 5 ADS7834 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25°C, VCC = +5V, fSAMPLE = 500kHz, fCLK = 16 • fSAMPLE, and internal +2.5V reference, unless otherwise specified. SIGNAL-TO-NOISE RATIO and SIGNAL-TO-(NOISE+DISTORTION) vs INPUT FREQUENCY FREQUENCY SPECTRUM (4096 Point FFT; fIN = 99.7kHz, –0.2dB) 0.00 76 SNR and SINAD (dB) –40 –60 –80 –100 72 70 SINAD 68 66 64 62 –120 60 0 50 100 150 200 250 1 10 SPURIOUS FREE DYNAMIC RANGE and TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY –90 85 –85 75 –80 –75 THD✻ –70 65 THD (dB) SFDR –65 60 –60 ✻ First nine harmonics of an input frequency 55 –55 50 1 10 100 –50 1000 0.3 fIN = 10kHz, –0.2dB) 0.2 0.1 0. SNR –0.1 –0.2 –0.3 SINAD –0.4 –0.5 –40 –20 0 20 40 Temperature (°C) Input Frequency (kHz) ® ADS7834 SNR and SINAD Delta from +25°C (dB) –95 90 70 1000 SIGNAL-TO-NOISE and SIGNAL-TO-(NOISE+DISTORTION) vs TEMPERATURE 95 80 100 Input Frequency (kHz) Frequency (kHz) SFDR (dB) Amplitude (dB) SNR 74 –20 6 60 80 100 THEORY OF OPERATION are common to both inputs. Thus, the –IN input is best used to sense a remote ground point near the source of the +IN signal. If the source driving the +IN signal is nearby, the –IN should be connected directly to ground. The ADS7834 is a high speed successive approximation register (SAR) analog-to-digital converter (A/D) with an internal 2.5V bandgap reference. The architecture is based on capacitive redistribution which inherently includes a sample/hold function. The converter is fabricated on a 0.6µ CMOS process. See Figure 1 for the basic operating circuit for the ADS7834. The input current into the analog input depends on input voltage and sample rate. Essentially, the current into the device must charge the internal hold capacitor (typically 20pF) during the sample period. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance to a 12-bit settling level within the sample period—which can be as little as 350ns in some operating modes. While the converter is in the hold mode or after the sampling capacitor has been fully charged, the input impedance of the analog input is greater than 1GΩ. The ADS7834 requires an external clock to run the conversion process. This clock can vary between 200kHz (12.5kHz throughput) and 8MHz (500kHz throughput). The duty cycle of the clock is unimportant as long as the minimum HIGH and LOW times are at least 50ns and the clock period is at least 125ns. The minimum clock frequency is set by the leakage on the capacitors internal to the ADS7834. Care must be taken regarding the input voltage on the +IN and –IN pins. To maintain the linearity of the converter, the +IN input should remain within the range of GND – 200mV to VREF + 200mV. The –IN input should not drop below GND – 200mV or exceed GND + 200mV. Outside of these ranges, the converter’s linearity may not meet specifications. The analog input is provided to two input pins: +IN and –IN. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. The range of the analog input is set by the voltage on the VREF pin. With the internal 2.5V reference, the input range is 0V to 2.5V. An external reference voltage can be placed on VREF, overdriving the internal voltage. The range for the external voltage is 2.0V to 2.55V, giving an input voltage range of 2.0V to 2.55V. REFERENCE The reference voltage on the VREF pin directly sets the fullscale range of the analog input. The ADS7834 can operate with a reference in the range of 2.0V to 2.55V, for a fullscale range of 2.0V to 2.55V. The digital result of the conversion is provided in a serial manner, synchronous to the CLK input. The result is provided most significant bit first and represents the result of the conversion currently in progress—there is no pipeline delay. By properly controlling the CONV and CLK inputs, it is possible to obtain the digital result least significant bit first. The voltage at the VREF pin is internally buffered and this buffer drives the capacitor DAC portion of the converter. This is important because the buffer greatly reduces the dynamic load placed on the reference source. However, the voltage at VREF will still contain some noise and glitches from the SAR conversion process. These can be reduced by carefully bypassing the VREF pin to ground as outlined in the sections that follow. ANALOG INPUT The +IN and –IN input pins allow for a differential input signal to be captured on the internal hold capacitor when the converter enters the hold mode. The voltage range on the –IN input is limited to –0.2V to 0.2V. Because of this, the differential input can be used to reject only small signals that INTERNAL REFERENCE The ADS7834 contains an on-board 2.5V reference, resulting in a 0V to 2.5V input range on the analog input. The specification table gives the various specifications for the +5V 2.2µF + ADS7834 0.1µF 0V to 2.5V Analog Input 0.1µF + 1 VREF +VCC 8 2 +IN CLK 7 Serial Clock 3 –IN DATA 6 Serial Data 4 GND CONV 5 Convert Start 10µF from Microcontroller or DSP FIGURE 1. Basic Operation of the ADS7834. ® 7 ADS7834 internal reference. This reference can be used to supply a small amount of source current to an external load, but the load should be static. Due to the internal 10kΩ resistor, a dynamic load will cause variations in the reference voltage, and will dramatically affect the conversion result. Note that even a static load will reduce the internal reference voltage seen at the buffer input. The amount of reduction depends on the load and the actual value of the internal “10kΩ” resistor. The value of this resistor can vary by ±30%. tCKP tCKH CLK tCKDS tCKDH DATA FIGURE 2. Serial Data and Clock Timing. The VREF pin should be bypassed with a 0.1µF capacitor placed as close as possible to the ADS7834 package. In addition, a 2.2 µF tantalum capacitor should be used in parallel with the ceramic capacitor. Placement of this capacitor, while not critical to performance, should be placed as close to the package as possible. SYMBOL EXTERNAL REFERENCE The internal reference is connected to the VREF pin and to the internal buffer via a 10kΩ series resistor. Thus, the reference voltage can easily be overdriven by an external reference voltage. The voltage range for the external voltage is 2.0V to 2.55V, corresponding to an analog input range of 2.0V to 2.55V. While the external reference will not source significant current into the VREF pin, it does have to drive the series 10kΩ resistor that is terminated into the 2.5V internal reference (the exact value of the resistor will vary up to ±30% from part to part). In addition, the VREF pin should still be bypassed to ground with at least a 0.1 µF ceramic capacitor (placed as close to the ADS7834 as possible). The reference will have to be stable with this capacitive load. Depending on the particular reference and A/D conversion speed, additional bypass capacitance may be required, such as the 2.2µF tantalum capacitor shown in Figure 1. Reasons for choosing an external reference over the internal reference vary, but there are two main reasons. One is to achieve a given input range. For example, a 2.048V reference provides for a 0V to 2.048V input range—or 500nV per LSB. The other is to provide greater stability over temperature. (The internal reference is typically 20ppm/°C which translates into a full-scale drift of roughly 1 output code for every 12°C. This does not take into account other sources of full-scale drift). If greater stability over temperature is needed, then an external reference with lower temperature drift will be required. DESCRIPTION MIN TYP MAX UNITS tACQ Acquisition Time 350 ns tCONV Conversion Time 1.625 µs tCKP Clock Period 125 tCKL Clock LOW 50 tCKH Clock HIGH 50 tCKDH Clock Falling to Current Data Bit No Longer Valid 5 tCKDS Clock Falling to Next Data Valid tCVL CONV LOW 5000 ns ns ns 15 30 ns 50 40 ns ns tCVH CONV HIGH 40 ns tCKCH CONV Hold after Clock Falls(1) 10 ns tCKCS CONV Setup to Clock Falling(1) 10 tCKDE Clock Falling to DATA Enabled 20 50 ns tCKDD Clock Falling to DATA High Impedance 70 100 ns ns tCKSP Clock Falling to Sample Mode 5 tCKPD Clock Falling to Power-Down Mode 50 ns tCVHD CONV Falling to Hold Mode (Aperture Delay) 5 ns ns tCVSP CONV Rising to Sample Mode 5 tCVPU CONV Rising to Full Power-up 50 tCVDD CONV Changing State to DATA High Impedance 70 tCVPD CONV Changing State to Power-Down Mode 50 tDRP CONV Falling to Start of CLK (for hold droop < 0.1 LSB) ns ns 100 ns ns 5 µs Note: (1) This timing is not required under some situations. See text for more information. TABLE I. Timing Specifications (TA = –40°C to +85°C, CLOAD = 30pF). The asynchronous nature of CONV to CLK raises some interesting possibilities, but also some design considerations. Figure 3 shows that CONV has timing restraints in relation to CLK (tCKCH and tCKCS). However, if these times are violated (which could happen if CONV is completely asynchronous to CLK), the converter will perform a conversion correctly, but the exact timing of the conversion is indeterminate. Since the setup and hold time between CONV and CLK has been violated in this example, the start of conversion could vary by one clock cycle. (Note that the start of conversion can be detected by using a pull-up resistor on DATA. When DATA drops out of high-impedance and goes LOW, the conversion has started and that clock cycle is the first of the conversion.) DIGITAL INTERFACE Figure 2 shows the serial data timing and Figure 3 shows the basic conversion timing for the ADS7834. The specific timing numbers are listed in Table I. There are several important items in Figure 3 which give the converter additional capabilities over typical 8-pin converters. First, the transition from sample mode to hold mode is synchronous to the falling edge of CONV and is not dependent on CLK. Second, the CLK input is not required to be continuous during the sample mode. After the conversion is complete, the CLK may be kept LOW or HIGH. In addition if CONV is completely asynchronous to CLK and CLK is continuous, then there is the possibility that CLK will transition just prior to CONV going LOW. If this ® ADS7834 tCKL 8 Figure 4 shows the typical method for placing the A/D into the power-down mode. If CONV is kept LOW during the conversion and is LOW at the start of the 13 clock cycle, then the device enters the power-down mode. It remains in this mode until the rising edge of CONV. Note that CONV must be HIGH for at least tACQ in order to sample the signal properly as well as to power-up the internal nodes. occurs faster than the 10ns indicated by tCKCH, then there is a chance that some digital feedthrough may be coupled onto the hold capacitor. This could cause a small offset error for that particular conversion. Thus, there are two basic ways to operate the ADS7834. CONV can be synchronous to CLK and CLK can be continuous. This would be the typical situation when interfacing the converter to a digital signal processor. The second method involves having CONV asynchronous to CLK and gating the operation of CLK (a non-continuous clock). This method would be more typical of an SPI-like interface on a microcontroller. This method would also allow CONV to be generated by a trigger circuit and to initiate (after some delay) the start of CLK. These two methods are covered under DSP Interfacing and SPI Interfacing. There are two different methods for clocking the ADS7834. The first involves scaling the CLK input in relation to the conversion rate. For example, an 8MHz input clock and the timing shown in Figure 3 results in a 500kHz conversion rate. Likewise, a 1.6MHz clock would result in a 100kHz conversion rate. The second method involves keeping the clock input as close to the maximum clock rate as possible and starting conversions as needed. This timing is similar to that shown in Figure 4. As an example, a 50kHz conversion rate would require 160 clock periods per conversion instead of the 16 clock periods used at 500kHz. POWER-DOWN TIMING The conversion timing shown in Figure 3 does not result in the ADS7834 going into the power-down mode. If the conversion rate of the device is high (approaching 500kHz), then there is very little power that can be saved by using the power-down mode. However, since the power-down mode incurs no conversion penalty (the very first conversion is valid), at lower sample rates, significant power can be saved by allowing the device to go into power-down mode between conversions. The main distinction between the two is the amount of time that the ADS7834 remains in power-down. In the first mode, the converter only remains in power-down for a small number of clock periods (depending on how many clock periods there are per each conversion). As the conversion rate scales, the converter always spends the same percentage of time in power-down. Since less power is drawn by the digital logic, there is a small decrease in power consumption, but it is very slight. This effect can be seen in the typical performance curve “Supply Current vs Sample Rate.” tCVL tCVCK CONV tCKCS tCKCH CLK 14 15 16 1 2 3 4 11 12 13 14 15 16 1 (1) tCKDE D11 (MSB) DATA tCKDD D10 D9 D2 D1 D0 (LSB) tACQ tCVHD SAMPLE/HOLD MODE tCKSP HOLD SAMPLE SAMPLE HOLD (2) tCONV INTERNAL CONVERSION STATE IDLE CONVERSION IN PROGRESS IDLE(3) NOTES: (1) Clock periods 14 and 15 are shown for clarity, but are not required for proper operation of the ADS7834, provided that the minimum tACQ time is met. The CLK input may remain HIGH or LOW during this period. (2) The transition from sample mode to hold mode occurs on the falling edge of CONV. This transition is not dependent on CLK. (3) The device remains fully powered when operated as shown. If the sample time is longer than 3 clock periods, power consumption can be reduced by allowing the device to enter a power-down mode. See the power-down timing for more information. FIGURE 3. Basic Conversion Timing. ® 9 ADS7834 CONV 1 CLK 2 D11 (MSB) DATA 3 12 D10 D1 13 D0 (LSB) tCVSP SAMPLE/HOLD SAMPLE MODE tACQ HOLD SAMPLE HOLD (3) INTERNAL CONVERSION STATE IDLE POWER MODE CONVERSION IN PROGRESS IDLE tCKPD tCVPU FULL POWER LOW POWER (1) FULL POWER (2) NOTES: (1) The low power mode (“power-down”) is entered when CONV remains LOW during the conversion and is still LOW at the start of the 13th clock cycle. (2) The low power mode is exited when CONV goes HIGH. (3) When in power-down, the transition from hold mode to sample mode is initiated by CONV going HIGH. FIGURE 4. Power-down Timing. tCVH CONV tCKCH 1 CLK 2 3 12 13 14 23 24 D10 D11 (MSB) tCKCS D11 (MSB) DATA D10 D0 (LSB) D1 D1 tCVDD (1) SAMPLE/HOLD SAMPLE MODE INTERNAL CONVERSION STATE IDLE LOW... (2) HOLD CONVERSION IN PROGRESS IDLE tCVPD POWER MODE FULL POWER LOW POWER (3) NOTES: (1) The serial data can be transmitted LSB first by pulling CONV LOW during the 13th clock cycle. (2) After the MSB has been transmitted, the DATA output pin will remain LOW until CONV goes HIGH. (3) When CONV is taken LOW to initiate the LSB first transfer, the converter enters the power-down mode. FIGURE 5. Serial Data “LSB-First” Timing. In contrast, the second method (clocking at a fixed rate) means that each conversion takes X clock cycles. As the time between conversions get longer, the converter remains in power-down an increasing percentage of time. This re- duces total power consumption by a considerable amount. For example, a 50kHz conversion rate results in roughly 1/10 of the power (minus the reference) that is used at a 500kHz conversion rate. ® ADS7834 10 Table II offers a look at the two different modes of operation and the difference in power consumption. fSAMPLE POWER WITH CLK = 16 • fSAMPLE POWER WITH CLK = 8MHz 500kHz 11mW 11mW 250kHz 10mW 7mW 100kHz 9mW 4mW the conversion will terminate immediately, before all 12 bits have been decided. This can be a very useful feature when a resolution of 12 bits is not needed. An example would be when the converter is being used to monitor an input voltage until some condition is met. At that time, the full resolution of the converter would then be used. Short-cycling the conversion can result in a faster conversion rate or lower power dissipation. There are several very important items shown in Figure 6. The conversion currently in progress is terminated when CONV is taken HIGH during the conversion and then taken LOW prior to tCKCH before the start of the 13th clock cycle. Note that if CONV goes LOW during the 13th clock cycle, then the LSB-first mode will be entered (Figure 5). Also, when CONV goes LOW, the DATA output immediately transitions to high impedance. If the output bit that is present during that clock period is needed, CONV must not go LOW until the bit has been properly latched into the receiving logic. TABLE II. Power Consumption versus CLK Input. LSB FIRST DATA TIMING Figure 5 shows a method to transmit the digital result in a least-significant bit (LSB) format. This mode is entered when CONV is pulled HIGH during the conversion (before the end of the 12th clock) and then pulled LOW during the 13th clock (when D0, the LSB, is being transmitted). The next 11 clocks then repeat the serial data, but in an LSB first format. The converter enters the power-down mode during the 13th clock and resumes normal operation when CONV goes HIGH. DATA FORMAT The ADS7834 output data is in straight binary format as shown in Figure 7. This figure shows the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. SHORT-CYCLE TIMING The conversion currently in progress can be “short-cycled” with the technique shown in Figure 6. This term means that tCVL (1) CONV tCVH 1 CLK 2 3 4 5 6 7 tCVDD D11 (MSB) DATA SAMPLE/HOLD MODE INTERNAL CONVERSION STATE D10 D9 D8 SAMPLE IDLE D7 D6 HOLD CONVERSION IN PROGRESS IDLE tCVPD POWER MODE FULL POWER LOW POWER NOTE: (1) The conversion currently in progress can be stopped by pulling CONV LOW during the conversion. This must occur at least tCKCS prior to the start of the 13th clock cycle. The DATA output pin will tri-state and the device will enter the power-down mode when CONV is pulled LOW. FIGURE 6. Short-cycle Timing. ® 11 ADS7834 microcontrollers form various manufacturers. CONV would be tied to a general purpose I/O pin (SPI) or to a PCX pin (QSPI), CLK would be tied to the serial clock, and DATA would be tied to the serial input data pin such as MISO (master in slave out). FS = Full-Scale Voltage = VREF 1 LSB = FS/4096 1 LSB 11...111 Note the time tDRP shown in Figure 9. This represents the maximum amount of time between CONV going LOW and the start of the conversion clock. Since CONV going LOW places the sample and hold in the hold mode and because the hold capacitor loses charge over time, there is a requirement that time tDRP be met as well as the maximum clock period (tCKP). Output Code 11...110 11...101 00...010 00...001 00...000 LAYOUT 2.499V(1) 0V Input Voltage(2) (V) For optimum performance, care should be taken with the physical layout of the ADS7834 circuitry. This is particularly true if the CLK input is approaching the maximum input rate. NOTES: (1) For external reference, value is VREF – 1 LSB. (2) Voltage at converter input: +IN – (–IN). FIGURE 7. Ideal Input Voltages and Output Codes. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Thus, during any single conversion for an n-bit SAR converter, there are n “windows” in which large external transient voltages can easily affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, and high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. The error can change if the external event changes in time with respect to the CLK input. DSP INTERFACING Figure 8 shows a timing diagram that might be used with a typical digital signal processor such as a TI DSP. For the buffered serial port (BSP) on the TMS320C54X family, CONV would tied to BFSX, CLK would be tied to BCLKX, and DATA would be tied to BDR. SPI/QSPI INTERFACING Figure 9 shows the timing diagram for a typical serial peripheral interface (SPI) or queued serial peripheral interface (QSPI). Such interfaces are found on a number of CONV CLK 15 16 1 2 D11 (MSB) DATA 3 D10 12 D1 13 14 15 D0 (LSB) 16 1 2 D11 (MSB) 3 4 D10 D9 2 3 FIGURE 8. Typical DSP Interface Timing. tDRP tACQ CONV 1 CLK 2 3 D11 (MSB) DATA 4 D10 13 D1 14 D0 (LSB) FIGURE 9. Typical SPI/QSPI Interface Timing. ® ADS7834 12 15 16 1 D11 (MSB) With this in mind, power to the ADS7834 should be clean and well bypassed. A 0.1µF ceramic bypass capacitor should be placed as close to the device as possible. In addition, a 1µF to 10µF capacitor is recommended. If needed, an even larger capacitor and a 5Ω or 10Ω series resistor my be used to lowpass filter a noisy supply. capacitor. An additional larger capacitor may also be used, if desired. If the reference voltage is external and originates from an op-amp, make sure that it can drive the bypass capacitor or capacitors without oscillation. The GND pin should be connected to a clean ground point. In many cases, this will be the “analog” ground. Avoid connections which are too near the grounding point of a microcontroller or digital signal processor. If needed, run a ground trace directly from the converter to the power supply entry point. The ideal layout will include an analog ground plane dedicated to the converter and associated analog circuitry. The ADS7834 draws very little current from an external reference on average as the reference voltage is internally buffered. However, glitches from the conversion process appear at the VREF input and the reference source must be able to handle this. Whether the reference is internal or external, the VREF pin should be bypassed with a 0.1µF ® 13 ADS7834 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated