® ADS ADS 834 ADS8344 ¤ 834 4 ¤ 4 For most current data sheet and other product information, visit www.burr-brown.com 16-Bit, 8-Channel Serial Output Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION ● PIN FOR PIN WITH ADS7844 The ADS8344 is an 8-channel, 16-bit sampling analog-to-digital converter (ADC) with a synchronous serial interface. Typical power dissipation is 10mW at a 100kHz throughput rate and a +5V supply. The reference voltage (VREF) can be varied between 500mV and VCC, providing a corresponding input voltage range of 0V to VREF. The device includes a shutdown mode which reduces power dissipation to under 15µW. The ADS8344 is guaranteed down to 2.7V operation. ● SINGLE SUPPLY: 2.7V to 5V ● 8-CHANNEL SINGLE-ENDED OR 4-CHANNEL DIFFERENTIAL INPUT ● UP TO 100kHz CONVERSION RATE ● 84dB SINAD ● SERIAL INTERFACE ● QSOP-20 AND SSOP-20 PACKAGES Low power, high speed, and on-board multiplexer make the ADS8344 ideal for battery operated systems such as personal digital assistants, portable multichannel data loggers, and measurement equipment. The serial interface also provides low-cost isolation for remote data acquisition. The ADS8344 is available in a QSOP-20 or a SSOP-20 package and is guaranteed over the –40°C to +85°C temperature range. APPLICATIONS ● ● ● ● ● DATA ACQUISITION TEST AND MEASUREMENT INDUSTRIAL PROCESS CONTROL PERSONAL DIGITAL ASSISTANTS BATTERY-POWERED SYSTEMS CH0 SAR CH1 DCLK CH2 CH3 CH4 Eight Channel Multiplexer CS Comparator Serial Interface and Control CH5 CH6 CDAC CH7 COM SHDN DIN DOUT BUSY VREF International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 2000 Burr-Brown Corporation PDS-1571A 1 Printed in U.S.A. April, 2000 ADS8344 SPECIFICATION: +5V At TA = –40°C to +85°C, +VCC = +5V, VREF = +5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. ADS8344E, N PARAMETER ANALOG INPUT Full-Scale Input Span Absolute Input Range CONDITIONS MIN Positive Input - Negative Input Positive Input Negative Input 0 –0.2 –0.2 Capacitance Leakage Current TYP ADS8344EB, NB MAX MIN VREF +VCC +0.2 +1.25 ✻ ✻ ✻ REFERENCE INPUT Range Resistance Input Current POWER SUPPLY REQUIREMENTS +VCC Quiescent Current ✻ ✻ ✻ = = = = 5Vp-p 5Vp-p 5Vp-p 5Vp-p at at at at 0.024 0 10kHz 10kHz 10kHz 10kHz ✻ ✻ ✻ ✻ ✻ 2.4 2.4 ✻ ✻ 0.5 +VCC 5 40 2.5 0.001 ✻ 100 3 3.0 –0.3 3.5 5.5 +0.8 ✻ ✻ ✻ 1.5 300 Power Dissipation 7.5 –40 ✻ ✻ ✻ ✻ ✻ 0.4 4.75 Clk Cycles Clk Cycles kHz ns ns ps MHz MHz MHz V GΩ µA µA µA ✻ V V V V ✻ Straight Binary Specified Performance Bits Bits LSB mV LSB(1) % LSB µVrms LSB(1) dB dB dB dB ✻ ✻ ✻ ✻ ✻ CMOS | IIH | ≤ +5µA | IIL | ≤ +5µA IOH = –250µA IOL = 250µA ✻ ✻ ✻ ✻ ✻ ✻ –90 86 92 100 DCLK Static 6 ±1 ✻ ±0.024 ✻ ✻ 100 VIN VIN VIN VIN V V V pF µA ✻ 500 30 100 2.4 fSAMPLE = 100kHz Power-Down Mode(3), CS = +VCC TEMPERATURE RANGE Specified Performance ✻ 16 fSAMPLE = 12.5kHz DCLK Static DIGITAL INPUT/OUTPUT Logic Family Logic Levels VIH VIL VOH VOL Data Format 8 ±2 4 ±0.05 4 4.5 Data Transfer Only DYNAMIC CHARACTERISTICS Total Harmonic Distortion(2) Signal-to-(Noise + Distortion) Spurious Free Dynamic Range Channel-to-Channel Isolation 1.0 20 3 SHDN = VDD ✻ ✻ ✻ 15 1.2 +4.75V < VCC < 5.25V UNITS ✻ 16 14 SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Internal Clock Frequency External Clock Frequency MAX ✻ ✻ 25 ±1 SYSTEM PERFORMANCE Resolution No Missing Codes Integral Linearity Error Offset Error Offset Error Match Gain Error Gain Error Match Noise Power Supply Rejection TYP 5.25 2.0 ✻ ✻ ✻ ✻ ✻ V mA µA µA mW ✻ °C ✻ 3 10 +85 ✻ ✻ Same specifications as ADS8344E. NOTES: (1) LSB means Least Significant Bit. With VREF equal to +5.0V, one LSB is 76µV. (2) First nine harmonics of the test frequency. (3) Auto power-down mode (PD1 = PD0 = 0) active or SHDN = GND. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® ADS8344 2 SPECIFICATION: +2.7V At TA = –40°C to +85°C, +VCC = +2.7V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. ADS8344E, N PARAMETER ANALOG INPUT Full-Scale Input Span Absolute Input Range CONDITIONS MIN Positive Input - Negative Input Positive Input Negative Input 0 –0.2 –0.2 TYP Capacitance Leakage Current SYSTEM PERFORMANCE Resolution No Missing Codes Integral Linearity Error Offset Error Offset Error Match Gain Error Gain Error Match Noise Power Supply Rejection SAMPLING DYNAMICS Conversion Time Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Internal Clock Frequency External Clock Frequency REFERENCE INPUT Range Resistance Input Current POWER SUPPLY REQUIREMENTS +VCC Quiescent Current ✻ ✻ ✻ TYP 1 20 3 +2.7 < VCC < +3.3V 12 ±1 4 ±0.05 4 ✻ ✻ ✻ ✻ 8 0.5 ✻ ±0.0024 ✻ ✻ ✻ 100 ✻ ✻ ✻ ✻ 500 30 100 2.4 SHDN = VDD 0.024 0 2.0 2.0 VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 1kHz VIN = 2.5Vp-p at 10kHz ✻ ✻ 0.5 +VCC DCLK Static 5 13 2.5 0.001 ✻ 40 3 ✻ ✻ ✻ 3.2 ✻ ✻ ✻ ✻ ✻ 0.4 V GΩ µA µA µA V V V V ✻ Straight Binary 1.2 220 Clk Cycles Clk Cycles kHz ns ns ps MHz MHz MHz ✻ 5.5 +0.8 2.7 Bits Bits LSB mV LSB % of FSR LSB µVrms LSB(1) dB dB dB dB ✻ ✻ ✻ ✻ ✻ CMOS +VCC • 0.7 –0.3 +VCC • 0.8 ✻ ✻ ✻ ✻ ✻ ✻ –90 86 92 100 –40 V V V pF µA ✻ 16 Power Dissipation ✻ ✻ ✻ ✻ 4.5 Specified Performance UNITS 15 1.2 | IIH | ≤ +5µA | IIL | ≤ +5µA IOH = –250µA IOL = 250µA MAX ✻ ✻ 16 fSAMPLE = 100kHz Power-Down Mode(3), CS = +VCC TEMPERATURE RANGE Specified Performance VREF +VCC +0.2 +0.2 14 fSAMPLE = 12.5kHz DCLK Static DIGITAL INPUT/OUTPUT Logic Family Logic Levels VIH VIL VOH VOL Data Format MIN 25 ±1 Data Transfer Only DYNAMIC CHARACTERISTICS Total Harmonic Distortion(2) Signal-to-(Noise + Distortion) Spurious Free Dynamic Range Channel-to-Channel Isolation ADS8344EB, NB MAX 3.6 1.85 ✻ ✻ ✻ 3 5 +85 ✻ ✻ ✻ ✻ ✻ V mA µA µA mW ✻ °C ✻ Same specifications as ADS8344E. NOTES: (1) LSB means Least Significant Bit. With VREF equal to +2.5V, one LSB is 38µV. (2) First nine harmonics of the test frequency. (3) Auto power-down mode (PD1 = PD0 = 0) active or SHDN = GND. ® 3 ADS8344 PIN DESCRIPTIONS PIN CONFIGURATION Top View CH0 1 20 +VCC CH1 2 19 DCLK CH2 3 18 CS CH3 4 17 DIN CH4 5 16 BUSY PIN NAME DESCRIPTION 1 2 3 4 5 6 7 8 9 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM 10 SHDN Analog Input Channel 0. Analog Input Channel 1. Analog Input Channel 2. Analog Input Channel 3. Analog Input Channel 4. Analog Input Channel 5. Analog Input Channel 6. Analog Input Channel 7. Ground reference for analog inputs. Sets zero code voltage in single ended mode. Connect this pin to ground or ground reference point. Shutdown. When LOW, the device enters a very low power shutdown mode. Voltage Reference Input. See Specification Table for ranges. Power Supply, 2.7V to 5V. Ground Ground Serial Data Output. Data is shifted on the falling edge of DCLK. This output is high impedance when CS is high. Busy Output. Busy goes low when the DIN control bits are being read and also when the device is converting. The Output is high impedance when CS is High. Serial Data Input. If CS is LOW, data is latched on rising edge of DCLK. Chip Select Input. Active LOW. Data will not be clocked into DIN unless CS is low. When CS is high DOUT is high impedance. External Clock Input. The clock speed determines the conversion rate by the equation fCLK = 24 • fSAMPLE. Power Supply ADS8344 CH5 6 15 DOUT CH6 7 14 GND CH7 8 13 GND 11 VREF COM 9 12 +VCC SHDN 10 11 VREF 12 13 14 15 +VCC GND GND DOUT 16 BUSY 17 DIN 18 CS 19 CLK 20 +VCC ABSOLUTE MAXIMUM RATINGS(1) +VCC to GND ........................................................................ –0.3V to +6V Analog Inputs to GND ............................................ –0.3V to +VCC + 0.3V Digital Inputs to GND ........................................................... –0.3V to +6V Power Dissipation .......................................................................... 250mW Maximum Junction Temperature ................................................... +150°C Operating Temperature Range ........................................ –40°C to +85°C Storage Temperature Range ......................................... –65°C to +150°C Lead Temperature (soldering, 10s) ............................................... +300°C NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT ADS8344E " ADS8344N " ADS8344EB " ADS8344NB " MINIMUM RELATIVE ACCURACY (LSB) MAXIMUM GAIN ERROR (%) SPECIFICATION TEMPERATURE RANGE 8 " " " 6 " " " ±0.05 " " " ±0.024 " " " –40°C to +85°C " " " –40°C to +85°C " " " PACKAGE PACKAGE DRAWING NUMBER ORDERING NUMBER(1) TRANSPORT MEDIA QSOP-20 " SSOP-20 " QSOP-20 " SSOP-20 " 349 " 334 " 349 " 334 " ADS8344E ADS8344E/2K5 ADS8344N ADS8344N/1K ADS8344EB ADS8344EB/2K5 ADS8344NB ADS8344NB/1K Rails Tape and Reel Rails Tape and Reel Rails Tape and Reel Rails Tape and Reel NOTES: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “ADS8344E/2K5” will get a single 2500-piece Tape and Reel. ® ADS8344 4 TYPICAL PERFORMANCE CURVES: +5V At TA = +25°C, +VCC = +5V, VREF = +5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.985kHz, –0.2dB) 0 0 –20 –20 –40 –40 Amplitude (dB) –60 –80 –100 –60 –80 –100 –120 –120 –140 –140 –160 –160 0 10 20 30 40 50 0 10 20 30 Frequency (kHz) SIGNAL-TO-NOISE RATIO AND SIGNAL-TO(NOISE+DISTORTION) vs INPUT FREQUENCY SPURIOUS FREE DYNAMIC RANGE AND TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY 100 50 –100 100 SNR SFDR 90 –90 90 SFDR (dB) SNR and SINAD (dB) 40 Frequency (kHz) 80 SINAD 70 THD(1) 80 –80 THD (dB) Amplitude (dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 1.001kHz, –0.2dB) –70 70 NOTE: (1) First Nine Harmonics of the Input Frequency 60 10 100 1 10 Frequency (kHz) Frequency (kHz) EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY CHANGE IN SIGNAL-TO-(NOISE+DISTORTION) vs TEMPERATURE 0.4 15.0 fIN = 9.985kHz, –0.2dB 14.5 0.2 14.0 Delta from +25°C (dB) Effective Number of Bits –60 100 60 1 13.5 13.0 12.5 12.0 0.0 –0.2 –0.4 –0.6 11.5 –0.8 11.0 1 10 –40 100 –25 0 20 50 75 100 Temperature (˚C) Frequency (kHz) ® 5 ADS8344 TYPICAL PERFORMANCE CURVES: +5V (Cont.) At TA = +25°C, +VCC = +5V, VREF = +5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. DIFFERENTIAL LINEARITY ERROR vs CODE 3 1 2 0 1 DLE (LSB) ILE (LSB) INTEGRAL LINEARITY ERROR vs CODE 2 –1 0 –2 –1 –3 –2 –4 0000H 4000H C000H 8000H –3 0000H FFFFH 8000H 4000H Output Code C000H FFFFH Output Code TYPICAL PERFORMANCE CURVES: +2.7V At TA = +25°C, +VCC = +2.7V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. FREQUENCY SPECTRUM (4096 Point FFT; fIN = 9.985kHz, –0.2dB) 0 0 –20 –20 –40 –40 Amplitude (dB) Amplitude (dB) FREQUENCY SPECTRUM (4096 Point FFT; fIN = 1.001kHz, –0.2dB) –60 –80 –100 –60 –80 –100 –120 –120 –140 –140 –160 –160 0 10 20 30 40 50 0 10 20 30 40 Frequency (kHz) Frequency (kHz) SIGNAL-TO-NOISE RATIO AND SIGNAL-TO(NOISE+DISTORTION) vs INPUT FREQUENCY SPURIOUS FREE DYNAMIC RANGE AND TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY 100 50 100 –100 90 –90 SFDR (dB) SNR and SINAD (dB) 80 70 SINAD 60 SFDR 80 70 –70 60 NOTE: (1) First Nine Harmonics of the Input Frequency 50 50 1 10 100 1 Frequency (kHz) ADS8344 10 Frequency (kHz) ® 6 –80 THD(1) –60 –50 100 THD (dB) SNR 90 TYPICAL PERFORMANCE CURVES: +2.7V (Cont.) At TA = +25°C, +VCC = +2.7V, VREF = +2.5V, fSAMPLE = 100kHz, and fCLK = 24 • fSAMPLE = 2.4MHz, unless otherwise noted. CHANGE IN SIGNAL-TO-(NOISE+DISTORTION) vs TEMPERATURE 15 2.0 14 1.5 Delta from +25°C (dB) Effective Number of Bits EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY 13 12 11 10 9 fIN = 9.985kHz, –0.2dB 1.0 0.5 0.0 –0.5 –1.0 –1.5 –2.0 8 1 10 –40 100 –25 0 2 1 1 DLE (LSB) 2 0 –1 –2 –2 C000H 8000H 75 100 0 –1 4000H 50 DIFFERENTIAL LINEARITY ERROR vs CODE 3 –3 0000H FFFFH 4000H Output Code 8000H C000H FFFFH Output Code SUPPLY CURRENT vs +VSS 1.6 fSAMPLE = 100kHz, VREF = +VSS 1.5 Supply Current (mA) ILE (LSB) INTEGRAL LINEARITY ERROR vs CODE 3 –3 0000H 20 Temperature (˚C) Frequency (kHz) 1.4 1.3 1.2 1.1 1.0 2.5 3.0 3.5 4.0 4.5 5.0 +VSS (V) ® 7 ADS8344 THEORY OF OPERATION ANALOG INPUT Figure 2 shows a block diagram of the input multiplexer on the ADS8344. The differential input of the converter is derived from one of the eight inputs in reference to the COM pin or four of the eight inputs. Table I and Table II show the relationship between the A2, A1, A0, and SGL/DIF control bits and the configuration of the analog multiplexer. The control bits are provided serially via the DIN pin, see the Digital Interface section of this data sheet for more details. The ADS8344 is a classic successive approximation register (SAR) analog-to-digital (A/D) converter. The architecture is based on capacitive redistribution which inherently includes a sample/hold function. The converter is fabricated on a 0.6µs CMOS process. The basic operation of the ADS8344 is shown in Figure 1. The device requires an external reference and an external clock. It operates from a single supply of 2.7V to 5.25V. The external reference can be any voltage between 500mV and +VCC. The value of the reference voltage directly sets the input range of the converter. The average reference input current depends on the conversion rate of the ADS8344. When the converter enters the hold mode, the voltage difference between the +IN and –IN inputs (see Figure 2) is captured on the internal capacitor array. The voltage on the –IN input is limited between –0.2V and 1.25V, allowing the input to reject small signals which are common to both the +IN and –IN input. The +IN input has a range of –0.2V to +VCC + 0.2V. The analog input to the converter is differential and is provided via an eight-channel multiplexer. The input can be provided in reference to a voltage on the COM pin (which is generally ground) or differentially by using four of the eight input channels (CH0 - CH7). The particular configuration is selectable via the digital interface. A2 A1 A0 0 0 0 1 0 0 0 0 1 1 0 1 0 1 0 1 1 0 0 1 1 1 1 1 The input current on the analog inputs depends on the conversion rate of the device. During the sample period, the source must charge the internal sampling capacitor (typi- A2 A1 A0 CH0 CH1 –IN 0 0 0 +IN –IN –IN 0 0 1 –IN 0 1 0 –IN 0 1 1 –IN 1 0 0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM +IN +IN +IN +IN +IN +IN +IN +IN –IN 1 0 1 –IN 1 1 0 –IN 1 1 1 TABLE I. Single-Ended Channel Selection (SGL/DIF HIGH). –IN CH2 CH3 +IN –IN CH4 CH5 +IN –IN –IN –IN –IN +IN +IN –IN 0.1µF 1µF to 10µF 1 CH0 +VCC 20 2 CH1 DCLK 19 3 CH2 CS 18 Chip Select 4 CH3 DIN 17 Serial Data In 5 CH4 BUSY 16 6 CH5 DOUT 15 7 CH6 GND 14 8 CH7 GND 13 9 COM +VCC 12 Serial/Conversion Clock Serial Data Out VREF 11 1µF to 10µF FIGURE 1. Basic Operation of the ADS8344. ® ADS8344 +IN +IN TABLE II. Differential Channel Control (SGL/DIF LOW). ADS8344 10 SHDN CH7 +IN +2.7V to +5V Single-ended or differential analog inputs CH6 8 Likewise, the noise or uncertainty of the digitized output will increase with lower LSB size. With a reference voltage of 500mV, the LSB size is 7.6µV. This level is below the internal noise of the device. As a result, the digital output code will not be stable and vary around a mean value by a number of LSBs. The distribution of output codes will be gaussian and the noise can be reduced by simply averaging consecutive conversion results or applying a digital filter. A2-A0 (shown 00oB)(1) CH0 CH1 CH2 CH3 CH4 With a lower reference voltage, care should be taken to provide a clean layout including adequate bypassing, a clean (low noise, low ripple) power supply, a low-noise reference, and a low-noise input signal. Because the LSB size is lower, the converter will also be more sensitive to nearby digital signals and electromagnetic interference. CH5 CH6 CH7 +IN Converter –IN The voltage into the VREF input is not buffered and directly drives the capacitor digital-to-analog converter (CDAC) portion of the ADS8344. Typically, the input current is 13µA with a 2.5V reference. This value will vary by microamps depending on the result of the conversion. The reference current diminishes directly with both conversion rate and reference voltage. As the current from the reference is drawn on each bit decision, clocking the converter more quickly during a given conversion period will not reduce overall current drain from the reference. COM NOTE: (1) See Truth Tables, Table I and Table II for address coding. DIGITAL INTERFACE SGL/DIF (shown HIGH) The ADS8344 has a four-wire serial interface compatible with several microprocessor families (note that the digital inputs are over-voltage tolerant up to +5.5V, regardless of +VCC). Figure 3 shows the typical operation of the ADS8344 digital interface. FIGURE 2. Simplified Diagram of the Analog Input. cally 25pF). After the capacitor has been fully charged, there is no further input current. The rate of charge transfer from the analog source to the converter is a function of conversion rate. Most microprocessors communicate using 8-bit transfers; the ADS8344 can complete a conversion with three such transfers, for a total of 24 clock cycles on the DCLK input, provided the timing is as shown in Figure 3. The first eight clock cycles are used to provide the control byte via the DIN pin. When the converter has enough information about the following conversion to set the input multiplexer appropriately, it enters the acquisition (sample) mode. After four more clock cycles, the control byte is complete and the converter enters the conversion mode. At this point, the input sample/hold goes into the hold mode. The next sixteen clock cycles accomplish the actual A/D conversion. REFERENCE INPUT The external reference sets the analog input range. The ADS8344 will operate with a reference in the range of 100mV to +VCC. Keep in mind that the analog input is the difference between the +IN input and the –IN input as shown in Figure 2. For example, in the single-ended mode, a 1.25V reference, and with the COM pin grounded, the selected input channel (CH0 - CH7) will properly digitize a signal in the range of 0V to 1.25V. If the COM pin is connected to 0.5V, the input range on the selected channel is 0.5V to 1.75V. Control Byte Also, shown in Figure 3 is the placement and order of the control bits within the control byte. Table III and IV give detailed information about these bits. The first bit, the “S” bit, must always be HIGH and indicates the start of the control byte. The ADS8344 will ignore inputs on the DIN pin until the start bit is detected. The next three bits (A2-A0) select the active input channel or channels of the input multiplexer (see Tables I and II and Figure 2). There are several critical items concerning the reference input and its wide voltage range. As the reference voltage is reduced, the analog voltage weight of each digital output code is also reduced. This is often referred to as the LSB (least significant bit) size and is equal to the reference voltage divided by 65536. Any offset or gain error inherent in the A/D converter will appear to increase, in terms of LSB size, as the reference voltage is reduced. For example, if the offset of a given converter is 2 LSBs with a 2.5V reference, then it will typically be 10 LSBs with a 0.5V reference. In each case, the actual offset of the device is the same, 76.3µV. The SGL/DIF-bit controls the multiplexer input mode: either single-ended mode, the selected input channel is referenced to the COM pin. In differential mode, the two selected ® 9 ADS8344 CS tACQ DCLK 1 8 Idle DIN S A2 1 8 Acquire A1 1 8 Idle SGL/ DIF PD1 PD0 A0 1 8 Conversion S A2 Acquire A1 1 Conversion SGL/ DIF PD1 PD0 A0 (START) (START) BUSY DOUT 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (MSB) 0 Zero Filled... 15 14 (MSB) (LSB) FIGURE 3. Conversion Timing, 24-Clocks per Conversion, 8-Bit Bus Interface. No DCLK delay required with dedicated serial port. inputs provide a differential input. See Tables I and II and Figure 2 for more information. The last two bits (PD1 - PD0) select the power-down mode and clock mode as shown in Table V. If both PD1 and PD0 are HIGH, the device is always powered up. If both PD1 and PD0 are low, the device enters a power-down mode between conversions. When a new conversion is initiated, the device will resume normal operation instantly—no delay is needed to allow the device to power up and the very first conversion will be valid. BIT 7 NAME Start Bit. Control byte starts with first HIGH bit on DIN. 6-4 A2 - A0 Channel Select Bits. Along with the SGL/DIF bit, these bits control the setting of the multiplexer input as detailed in Tables I and II. 2 SGL/DIF Single-Ended/Differential Select Bit. Along with bits A2 - A0, this bit controls the setting of the multiplexer input as detailed in Tables I and II. PD1 - PD0 Power-Down Mode Select Bits. See Table V for details. 1-0 Clock Modes The ADS8344 can be used with an external serial clock or an internal clock to perform the successive-approximation conversion. In both clock modes, the external clock shifts data in and out of the device. Internal clock mode is selected when PD1 is HIGH and PD0 is LOW. DESCRIPTION S TABLE IV. Descriptions of the Control Bits within the Control Byte. PD0 PD1 0 0 Power-down between conversions. When each conversion is finished, the converter enters a low power mode. At the start of the next conversion, the device instantly powers up to full power. There is no need for additional delays to assure full operation and the very first conversion is valid. Description 0 1 Internal clock mode. 1 0 Reserved for future use. 1 1 No power-down between conversions, device always powered. External Clock Mode In external clock mode, the external clock not only shifts data in and out of the ADS8344, it also controls the A/D conversion steps. BUSY will go HIGH for one clock period after the last bit of the control byte is shifted in. Successiveapproximation bit decisions are made and appear at DOUT on each of the next 16 SCLK falling edges (Figure 3). Figure 4 shows the BUSY timing in external clock mode. Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 (LSB) S A2 A1 A0 — SGL/DIF PD1 PD0 TABLE V. Power-Down Selection. TABLE III. Order of the Control Bits in the Control Byte. CS tCSS tCL tCH tBD tBD tD0 tCSH DCLK tDS DIN tDH PD0 tBDV tBTR BUSY tDV tTR DOUT 15 FIGURE 4. Detailed Timing Diagram. ® ADS8344 10 14 Since one clock cycle of the serial clock is consumed with BUSY going high (while the MSB decision is being made), 16 additional clocks must be given to clock out all 16 bits of data; thus, one conversion takes a minimum of 25 clock cycles to fully read the data. Since most microprocessors communicate in 8-bit transfers, this means that an additional transfer must be made to capture the LSB. If CS is LOW when BUSY goes LOW following a conversion, the next falling edge of the external serial clock will write out the MSB on the DOUT line. The remaining bits (D14-D0) will be clocked out on each successive clock cycle following the MSB. If CS is HIGH when BUSY goes LOW then the DOUT line will remain in tri-state until CS goes LOW (Figure 6). CS does not need to remain LOW once a conversion has started. Note that BUSY is not tri-stated when CS goes HIGH in internal clock mode. There are two ways of handling this requirement. One is shown in Figure 3, where the beginning of the next control byte appears at the same time the LSB is being clocked out of the ADS8344. This method allows for maximum throughput and 24 clock cycles per conversion. Data can be shifted in and out of the ADS8344 at clock rates exceeding 2.4MHz, provided that the minimum acquisition time tACQ, is kept above 1.7µs. Digital Timing The other method is shown in Figure 5, which uses 32 clock cycles per conversion; the last seven clock cycles simply shift out zeros on the DOUT line. BUSY and DOUT go into a high-impedance state when CS goes high; after the next CS falling edge, BUSY will go LOW. Figure 4 and Tables VI and VII provide detailed timing for the digital interface of the ADS8344. SYMBOL Internal Clock Mode In internal clock mode, the ADS8344 generates its own conversion clock internally. This relieves the microprocessor from having to generate the SAR conversion clock and allows the conversion result to be read back at the processor’s convenience, at any clock rate up to 2.4MHz. BUSY goes HIGH at the start of conversion and then returns LOW when the conversion is complete. During the conversion, BUSY will remain LOW for a maximum of 8µs. Also, during the conversion, SCLK should remain LOW to achieve the best noise performance. The conversion result is stored in an internal register; the data may be clocked out of this register any time after the conversion is complete. DESCRIPTION MIN TYP MAX UNITS µs tACQ Acquisition Time 1.5 tDS DIN Valid Prior to DCLK Rising 100 ns tDH DIN Hold After DCLK HIGH 10 ns tDO DCLK Falling to DOUT Valid 200 tDV CS Falling to DOUT Enabled 200 ns tTR CS Rising to DOUT Disabled 200 ns ns tCSS CS Falling to First DCLK Rising 100 ns tCSH CS Rising to DCLK Ignored 0 ns tCH DCLK HIGH 200 ns tCL DCLK LOW 200 ns tBD DCLK Falling to BUSY Rising 200 tBDV CS Falling to BUSY Enabled 200 ns ns tBTR CS Rising to BUSY Disabled 200 ns TABLE VI. Timing Specifications (+VCC = +2.7V to 3.6V, TA = –40°C to +85°C, CLOAD = 50pF). CS tACQ DCLK 1 8 Idle DIN S A2 8 1 Acquire A1 A0 1 8 1 8 Conversion Idle SGL/ PD1 PD0 DIF (START) BUSY DOUT 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Zero Filled... 0 (MSB) (LSB) FIGURE 5. CS tACQ DCLK 1 8 Idle DIN S A2 Acquire A1 A0 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Conversion SGL/ PD1 PD0 DIF (START) BUSY DOUT 15 14 13 12 (MSB) 11 10 9 8 7 6 5 4 3 2 1 0 Zero Filled... (LSB) FIGURE 6. ® 11 ADS8344 SYMBOL DESCRIPTION MIN tACQ Acquisition Time 1.7 TYP MAX tDS DIN Valid Prior to DCLK Rising 50 ns tDH DIN Hold After DCLK HIGH 10 ns slowing the frequency of the DCLK input, the two modes remain approximately equal. However, if the DCLK frequency is kept at the maximum rate during a conversion, but conversions are simply done less often, then the difference between the two modes is dramatic. In the latter case, the converter spends an increasing percentage of its time in power-down mode (assuming the auto power-down mode is active). UNITS µs tDO DCLK Falling to DOUT Valid 100 tDV CS Falling to DOUT Enabled 70 ns tTR CS Rising to DOUT Disabled 70 ns ns tCSS CS Falling to First DCLK Rising 50 ns tCSH CS Rising to DCLK Ignored 0 ns tCH DCLK HIGH 150 ns tCL DCLK LOW 150 ns tBD DCLK Falling to BUSY Rising 100 tBDV CS Falling to BUSY Enabled 70 ns tBTR CS Rising to BUSY Disabled 70 ns If DCLK is active and CS is LOW while the ADS8344 is in auto power-down mode, the device will continue to dissipate some power in the digital logic. The power can be reduced to a minimum by keeping CS HIGH. ns Operating the ADS8344 in auto power-down mode will result in the lowest power dissipation, and there is no conversion time “penalty” on power-up. The very first conversion will be valid. SHDN can be used to force an immediate power-down. TABLE VII. Timing Specifications (+VCC = +4.75V to +5.25V, TA = –40°C to +85°C, CLOAD = 50pF). Data Format The ADS8344 output data is in straight binary format as shown in Figure 7. This figure shows the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. NOISE The noise floor of the ADS8344 itself is extremely low, as can be seen from Figures 8 thru 11, and is much lower than competing A/D converters. The ADS8344 was tested at both 5V and 2.7V and in both the internal and external clock modes. A low level DC input was applied to the analog input pins and the converter was put through 5,000 conversions. The digital output of the A/D converter will vary in output code due to the internal noise of the ADS8344. This is true for all 16-bit SAR-type A/D converters. Using a histogram to plot the output codes, the distribution should appear bellshaped with the peak of the bell curve representing the nominal code for the input value. The ±1σ, ±2σ, and ±3σ distributions will represent the 68.3%, 95.5%, and 99.7%, respectively, of all codes. The transition noise can be calculated by dividing the number of codes measured by 6 and this will yield the ±3σ distribution or 99.7% of all codes. Statistically, up to 3 codes could fall outside the distribution when executing 1000 conversions. The ADS8344, with < 3 output codes for the ±3σ distribution, will yield a < ±0.5LSB transition noise at 5V operation. Remember, to achieve this low noise performance, the peak-to-peak noise of the input signal and reference must be < 50µV. FS = Full-Scale Voltage = VREF 1 LSB = VREF/65,536 1 LSB 11...111 Output Code 11...110 11...101 00...010 00...001 00...000 FS – 1 LSB 0V Input Voltage(1) (V) NOTE(1): Voltage at converter input, after multiplexer: +IN–(–IN). (See Figure 2.) FIGURE 7. Ideal Input Voltages and Output Codes. POWER DISSIPATION 4561 There are three power modes for the ADS8344: full power (PD1 - PD0 = 11B), auto power-down (PD1 - PD0 = 00B), and shutdown (SHDN LOW). The effects of these modes varies depending on how the ADS8344 is being operated. For example, at full conversion rate and 24-clocks per conversion, there is very little difference between full power mode and auto power-down, a shutdown (SHDN LOW) will not lower power dissipation When operating at full-speed and 24-clocks per conversion (as shown in Figure 3), the ADS8344 spends most of its time acquiring or converting. There is little time for auto powerdown, assuming that this mode is active. Thus, the difference between full power mode and auto power-down is negligible. If the conversion rate is decreased by simply 242 7FFD 7FFE 7FFF 197 0 8000 8001 Code FIGURE 8. Histogram of 5000 Conversions of a DC Input at the Code Transition, 5V operation external clock mode. ® ADS8344 0 12 sion results will reduce the transition noise by 1/2 to ±0.25 LSBs. Averaging should only be used for input signals with frequencies near DC. For AC signals, a digital filter can be used to low pass filter and decimate the output codes. This works in a similar manner to averaging; for every decimation by 2, the signalto-noise ratio will improve 3dB. 4507 LAYOUT 0 251 7FFD 7FFE 7FFF 242 0 8000 8001 For optimum performance, care should be taken with the physical layout of the ADS8344 circuitry. This is particularly true if the reference voltage is low and/or the conversion rate is high. Code The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Thus, during any single conversion for an n-bit SAR converter, there are n “windows” in which large external transient voltages can easily affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, and high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. The error can change if the external event changes in time with respect to the DCLK input. FIGURE 9. Histogram of 5000 Conversions of a DC Input at the Code Center, 5V operation internal clock mode. 3511 666 721 50 7FFD With this in mind, power to the ADS8344 should be clean and well bypassed. A 0.1µF ceramic bypass capacitor should be placed as close to the device as possible. In addition, a 1µF to 10µF capacitor and a 5Ω or 10Ω series resistor may be used to lowpass filter a noisy supply. 52 7FFE 7FFF 8000 8001 Code The reference should be similarly bypassed with a 0.1µF capacitor. Again, a series resistor and large capacitor can be used to lowpass filter the reference voltage. If the reference voltage originates from an op amp, make sure that it can drive the bypass capacitor without oscillation (the series resistor can help in this case). The ADS8344 draws very little current from the reference on average, but it does place larger demands on the reference circuitry over short periods of time (on each rising edge of DCLK during a conversion). FIGURE 10. Histogram of 5000 Conversions of a DC Input at the Code Transition, 2.7V operation external clock mode. 2868 The ADS8344 architecture offers no inherent rejection of noise or voltage variation in regards to the reference input. This is of particular concern when the reference input is tied to the power supply. Any noise and ripple from the supply will appear directly in the digital results. While high frequency noise can be filtered out as discussed in the previous paragraph, voltage variation due to line frequency (50Hz or 60Hz) can be difficult to remove. 1137 858 78 7FFD 59 7FFE 7FFF 8000 8001 Code The GND pin should be connected to a clean ground point. In many cases, this will be the “analog” ground. Avoid connections which are too near the grounding point of a microcontroller or digital signal processor. If needed, run a ground trace directly from the converter to the power supply entry point. The ideal layout will include an analog ground plane dedicated to the converter and associated analog circuitry. FIGURE 11. Histogram of 5000 Conversions of a DC Input at the Code Center, 2.7V operation internal clock mode. AVERAGING The noise of the A/D converter can be compensated by averaging the digital codes. By averaging conversion results, transition noise will be reduced by a factor of 1/√n, where n is the number of averages. For example, averaging 4 conver- ® 13 ADS8344