M
PIC16C5X
EPROM/ROM-Based 8-Bit CMOS Microcontroller Series
•
•
•
•
•
Devices Included in this Data Sheet:
•
•
•
•
•
•
•
•
•
•
PIC16C52
PIC16C54s
PIC16CR54s
PIC16C55s
PIC16C56s
PIC16CR56s
PIC16C57s
PIC16CR57s
PIC16C58s
PIC16CR58s
Note:
Peripheral Features:
The letter "s" used following the part
numbers throughout this document
indicate plural, meaning there is more
than one part variety for the indicated
device.
High-Performance RISC CPU:
• Only 33 single word instructions to learn
• All instructions are single cycle (200 ns) except for
program branches which are two-cycle
• Operating speed: DC - 20 MHz clock input
DC - 200 ns instruction cycle
Device
PIC16C52
PIC16C54
PIC16C54A
PIC16C54B
PIC16CR54A
PIC16CR54B
PIC16C55
PIC16C55A
PIC16C56
PIC16C56A
PIC16CR56A
PIC16C57
PIC16C57C
PIC16CR57B
PIC16CR57C
PIC16C58A
PIC16C58B
PIC16CR58A
PIC16CR58B
12-bit wide instructions
8-bit wide data path
Seven or eight special function hardware registers
Two-level deep hardware stack
Direct, indirect and relative addressing modes for
data and instructions
Pins
I/O
18
18
18
18
18
18
28
28
18
18
18
28
28
28
28
18
18
18
18
12
12
12
12
12
12
20
20
12
12
12
20
20
20
20
12
12
12
12
1997 Microchip Technology Inc.
EPROM/
RAM
ROM
384
512
512
512
512
512
512
512
1K
1K
1K
2K
2K
2K
2K
2K
2K
2K
2K
25
25
25
25
25
25
24
24
25
25
25
72
72
72
72
73
73
73
73
• 8-bit real time clock/counter (TMR0) with 8-bit
programmable prescaler
• Power-On Reset (POR)
• Device Reset Timer (DRT)
• Watchdog Timer (WDT) with its own on-chip
RC oscillator for reliable operation
• Programmable code-protection
• Power saving SLEEP mode
• Selectable oscillator options:
- RC:
Low-cost RC oscillator
- XT:
Standard crystal/resonator
- HS:
High-speed crystal/resonator
- LP:
Power saving, low-frequency crystal
CMOS Technology:
• Low-power, high-speed CMOS EPROM/ROM
technology
• Fully static design
• Wide-operating voltage and temperature range:
- EPROM Commercial/Industrial 2.0V to 6.25V
- ROM Commercial/Industrial 2.0V to 6.25V
- EPROM Extended 2.5V to 6.0V
- ROM Extended 2.5V to 6.0V
• Low-power consumption
- < 2 mA typical @ 5V, 4 MHz
- 15 µA typical @ 3V, 32 kHz
- < 0.6 µA typical standby current
(with WDT disabled) @ 3V, 0°C to 70°C
Note:
Preliminary
In this document, figure and table titles
refer to all varieties of the part number
indicated, (i.e., The title "Figure 14-1:
Load Conditions - PIC16C54A", also
refers to PIC16LC54A and PIC16LV54A
parts).
DS30453A-page 1
PIC16C5X
Pin Diagrams
PDIP, SOIC, Windowed CERDIP
18
17
16
15
14
13
12
11
10
RA1
RA0
OSC1/CLKIN
OSC2/CLKOUT
VDD
RB7
RB6
RB5
RB4
28
MCLR/VPP
2
27
OSC1/CLKIN
N/C
3
26
VSS
4
25
24
RC7
23
RC6
OSC2/CLKOUT
N/C
5
RA0
6
RA1
7
RA2
8
RA3
9
20
RC4
RB0
10
19
RC3
RB1
11
18
RB2
12
17
RB3
13
16
RB4
14
15
22
RC5
21
RC2
RC1
RC0
SSOP
SSOP
DS30453A-page 2
20
19
18
17
16
15
14
13
12
11
RA1
RA0
OSC1/CLKIN
OSC2/CLKOUT
VDD
VDD
RB7
RB6
RB5
RB4
Preliminary
VSS
T0CKI
VDD
VDD
RA0
RA1
RA2
RA3
RB0
RB1
RB2
RB3
RB4
VSS
•1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIC16C55s
PIC16C57s
PIC16CR57s
•1
2
3
4
5
6
7
8
9
10
PIC16C54s
PIC16CR54s
PIC16C56s
PIC16CR56s
PIC16C58s
PIC16CR58s
RA2
RA3
T0CKI
MCLR/VPP
VSS
VSS
RB0
RB1
RB2
RB3
•1
VDD
T0CKI
PIC16C55s
PIC16C57s
PIC16CR57s
PIC16C52s
PIC16C54s
PIC16CR54s
PIC16C56s
PIC16CR56s
PIC16C58s
PIC16CR58s
•1
2
3
4
5
6
7
8
9
RA2
RA3
T0CKI
MCLR/VPP
VSS
RB0
RB1
RB2
RB3
PDIP, SOIC, Windowed CERDIP
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MCLR/VPP
OSC1/CLKIN
OSC2/CLKOUT
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
RB7
RB6
RB5
1997 Microchip Technology Inc.
PIC16C5X
Device Differences
Device
Voltage
Range
Oscillator
Selection
(Program)
Oscillator
Process
Technology
(Microns)
ROM
Equivalent
MCLR
Filter
PIC16C52
3.0-6.25
User
See Note 1
0.9
—
No
PIC16C54
2.5-6.25
Factory
See Note 1
1.2
PIC16CR54A
No
PIC16C54A
2.0-6.25
User
See Note 1
0.9
—
No
PIC16C54B
3.0-5.5
User
See Note 1
0.7
PIC16CR54B
Yes
PIC16C55
2.5-6.25
Factory
See Note 1
1.7
—
No
PIC16C55A
3.0-5.5
User
See Note 1
0.7
—
Yes
PIC16C56
2.5-6.25
Factory
See Note 1
1.7
—
No
PIC16C56A
3.0-5.5
User
See Note 1
0.7
PIC16CR56A
Yes
PIC16C57
2.5-6.25
Factory
See Note 1
1.2
—
No
PIC16C57C
3.0-5.5
User
See Note 1
0.7
PIC16CR57C
Yes
PIC16CR57C
2.5-5.5
Factory
See Note 1
0.7
NA
Yes
PIC16C58A
2.0-6.25
User
See Note 1
0.9
PIC16CR58A
No(2)
PIC16C58B
3.0-5.5
User
See Note 1
0.7
PIC16CR58B
Yes
PIC16CR54A
2.5-6.25
Factory
See Note 1
1.2
NA
Yes
PIC16CR54B
2.5-5.5
Factory
See Note 1
0.7
NA
Yes
PIC16CR56A
2.5-5.5
Factory
See Note 1
0.7
NA
Yes
PIC16CR57B
2.5-6.25
Factory
See Note 1
0.9
NA
Yes
PIC16CR58A
2.5-6.25
Factory
See Note 1
0.9
NA
Yes
PIC16CR58B
2.5-5.5
Factory
See Note 1
0.7
NA
Yes
Note 1: If you change from this device to another device, please verify oscillator characteristics in your application.
Note 2: In PIC16LV58A, MCLR Filter = Yes
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 3
PIC16C5X
Table of Contents
1.0 General Description .............................................................................................................................................5
2.0 PIC16C5X Device Varieties.................................................................................................................................7
3.0 Architectural Overview.........................................................................................................................................9
4.0 Memory Organization ........................................................................................................................................15
5.0 I/O Ports.............................................................................................................................................................25
6.0 Timer0 Module and TMR0 Register...................................................................................................................27
7.0 Special Features of the CPU .............................................................................................................................31
8.0 Instruction Set Summary ...................................................................................................................................43
9.0 Development Support ........................................................................................................................................55
10.0 Electrical Characteristics - PIC16C52................................................................................................................59
11.0 Electrical Characteristics - PIC16C54/55/56/57.................................................................................................67
12.0 DC and AC Characteristics - PIC16C54/55/56/57 .............................................................................................81
13.0 Electrical Characteristics - PIC16CR54A...........................................................................................................89
14.0 Electrical Characteristics - PIC16C54A ...........................................................................................................103
15.0 Electrical Characteristics - PIC16CR57B.........................................................................................................117
16.0 Electrical Characteristics - PIC16C58A ...........................................................................................................131
17.0 Electrical Characteristics - PIC16CR58A.........................................................................................................145
18.0 DC and AC Characteristics - PIC16C54A/CR57B/C58A/CR58A ....................................................................159
19.0 Electrical Characteristics - PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B .................................................171
20.0 DC and AC Characteristics - PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B..............................................183
21.0 Packaging Information .....................................................................................................................................193
Appendix A: Compatibility ...........................................................................................................................................205
Index............................................................................................................................................................................207
PIC16C5X Product Identification System....................................................................................................................215
PIC16C54/55/56/57 Product Identification System .....................................................................................................216
DS30453A-page 4
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
1.0
GENERAL DESCRIPTION
1.1
The PIC16C5X from Microchip Technology is a family
of low-cost, high performance, 8-bit, fully static,
EPROM/ ROM-based CMOS microcontrollers. It
employs a RISC architecture with only 33 single
word/single cycle instructions. All instructions are single cycle (200 ns) except for program branches which
take two cycles. The PIC16C5X delivers performance
an order of magnitude higher than its competitors in the
same price category. The 12-bit wide instructions are
highly symmetrical resulting in 2:1 code compression
over other 8-bit microcontrollers in its class. The easy
to use and easy to remember instruction set reduces
development time significantly.
The PIC16C5X products are equipped with special features that reduce system cost and power requirements.
The Power-On Reset (POR) and Device Reset Timer
(DRT) eliminate the need for external reset circuitry.
There are four oscillator configurations to choose from,
including the power-saving LP (Low Power) oscillator
and cost saving RC oscillator. Power saving SLEEP
mode, Watchdog Timer and code protection features
improve system cost, power and reliability.
Applications
The PIC16C5X series fits perfectly in applications ranging from high-speed automotive and appliance motor
control to low-power remote transmitters/receivers,
pointing devices and telecom processors. The EPROM
technology makes customizing application programs
(transmitter codes, motor speeds, receiver frequencies, etc.) extremely fast and convenient. The small
footprint packages, for through hole or surface mounting, make this microcontroller series perfect for applications with space limitations. Low-cost, low-power, high
performance, ease of use and I/O flexibility make the
PIC16C5X series very versatile even in areas where no
microcontroller use has been considered before (e.g.,
timer functions, replacement of “glue” logic in larger
systems, coprocessor applications).
The UV erasable CERDIP packaged versions are ideal
for code development, while the cost-effective One
Time Programmable (OTP) versions are suitable for
production in any volume. The customer can take full
advantage of Microchip’s price leadership in OTP
microcontrollers while benefiting from the OTP’s
flexibility.
The PIC16C5X products are supported by a
full-featured macro assembler, a software simulator, an
in-circuit emulator, a ‘C’ compiler, fuzzy logic support
tools, a low-cost development programmer, and a full
featured programmer. All the tools are supported on
IBM PC and compatible machines.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 5
PIC16C5X
TABLE 1-1:
PIC16C5X FAMILY OF DEVICES
PIC16C52
Clock
Memory
Peripherals
Features
PIC16C54s
PIC16CR54s
PIC16C55s
PIC16C56s
Maximum Frequency
of Operation (MHz)
4
20
20
20
20
EPROM Program Memory
(x12 words)
384
512
—
512
1K
ROM Program Memory
(x12 words)
—
—
512
—
—
RAM Data Memory (bytes)
25
25
25
24
25
Timer Module(s)
TMR0
TMR0
TMR0
TMR0
TMR0
12
I/O Pins
12
12
12
20
Number of Instructions
33
33
33
33
33
Packages
18-pin DIP,
SOIC
18-pin DIP,
SOIC;
20-pin SSOP
18-pin DIP,
SOIC;
20-pin SSOP
28-pin DIP,
SOIC;
28-pin SSOP
18-pin DIP,
SOIC;
20-pin SSOP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer (except PIC16C52), selectable code
protect and high I/O current capability.
PIC16CR56s
Clock
Memory
Peripherals
Features
PIC16C57s
PIC16CR57s
PIC16C58s
PIC16CR58s
Maximum Frequency
of Operation (MHz)
20
20
20
20
20
EPROM Program Memory
(x12 words)
—
2K
—
2K
—
ROM Program Memory
(x12 words)
1K
—
2K
—
2K
RAM Data Memory (bytes)
25
72
72
73
73
Timer Module(s)
TMR0
TMR0
TMR0
TMR0
TMR0
I/O Pins
12
20
20
12
12
Number of Instructions
33
33
33
33
33
Packages
18-pin DIP,
SOIC;
20-pin SSOP
28-pin DIP,
SOIC;
28-pin SSOP
28-pin DIP,
SOIC;
28-pin SSOP
18-pin DIP,
SOIC;
20-pin SSOP
18-pin DIP,
SOIC;
20-pin SSOP
All PIC16/17 Family devices have Power-on Reset, selectable Watchdog Timer (except PIC16C52), selectable code
protect and high I/O current capability.
DS30453A-page 6
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
2.0
PIC16C5X DEVICE VARIETIES
A variety of frequency ranges and packaging options
are available. Depending on application and
production requirements, the proper device option can
be selected using the information in this section. When
placing orders, please use the PIC16C5X Product
Identification System at the back of this data sheet to
specify the correct part number.
For the PIC16C5X family of devices, there are four
device types, as indicated in the device number:
1.
2.
3.
4.
5.
2.1
C, as in PIC16C54. These devices have
EPROM program memory and operate over the
standard voltage range.
LC, as in PIC16LC54A. These devices have
EPROM program memory and operate over an
extended voltage range.
LV, as in PIC16LV54A. These devices have
EPROM program memory and operate over a
2.0V to 3.8V range.
CR, as in PIC16CR54A. These devices have
ROM program memory and operate over the
standard voltage range.
LCR, as in PIC16LCR54B. These devices have
ROM program memory and operate over an
extended voltage range.
UV Erasable Devices (EPROM)
The UV erasable versions, offered in CERDIP
packages, are optimal for prototype development and
pilot programs
UV erasable devices can be programmed for any of
the four oscillator configurations. Microchip's
PICSTART and PRO MATE programmers both
support programming of the PIC16C5X. Third party
programmers also are available; refer to the Third
Party Guide for a list of sources.
2.2
2.3
Quick-Turnaround-Production (QTP)
Devices
Microchip offers a QTP Programming Service for
factory production orders. This service is made
available for users who choose not to program a
medium to high quantity of units and whose code
patterns have stabilized. The devices are identical to
the OTP devices but with all EPROM locations and
configuration bit options already programmed by the
factory. Certain code and prototype verification
procedures apply before production shipments are
available. Please contact your Microchip Technology
sales office for more details.
2.4
Serialized
Quick-Turnaround-Production
(SQTP SM) Devices
Microchip offers the unique programming service
where a few user-defined locations in each device are
programmed with different serial numbers. The serial
numbers may be random, pseudo-random or
sequential. The devices are identical to the OTP
devices but with all EPROM locations and
configuration bit options already programmed by the
factory.
Serial programming allows each device to have a
unique number which can serve as an entry code,
password or ID number.
2.5
Read Only Memory (ROM) Devices
Microchip offers masked ROM versions of several of
the highest volume parts, giving the customer a low
cost option for high volume, mature products.
One-Time-Programmable (OTP)
Devices
The availability of OTP devices is especially useful for
customers expecting frequent code changes and
updates.
The OTP devices, packaged in plastic packages,
permit the user to program them once. In addition to
the program memory, the configuration bits must be
programmed.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 7
PIC16C5X
NOTES:
DS30453A-page 8
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
3.0
ARCHITECTURAL OVERVIEW
The high performance of the PIC16C5X family can be
attributed to a number of architectural features
commonly found in RISC microprocessors. To begin
with, the PIC16C5X uses a Harvard architecture in
which program and data are accessed on separate
buses. This improves bandwidth over traditional von
Neumann architecture where program and data are
fetched on the same bus. Separating program and
data memory further allows instructions to be sized
differently than the 8-bit wide data word. Instruction
opcodes are 12-bits wide making it possible to have all
single word instructions. A 12-bit wide program
memory access bus fetches a 12-bit instruction in a
single cycle. A two-stage pipeline overlaps fetch and
execution of instructions. Consequently, all instructions
(33) execute in a single cycle (200ns @ 20MHz)
except for program branches.
The PIC16C52 addresses 384 x 12 of program
memory, the PIC16C54s/CR54s and PIC16C55s
address 512 x 12 of program memory, the
PIC16C56s/CR56s address 1K X 12 of program
memory,
and
the
PIC16C57s/CR57s
and
PIC16C58s/CR58s address 2K x 12 of program
memory. All program memory is internal.
The PIC16C5X device contains an 8-bit ALU and
working register. The ALU is a general purpose
arithmetic unit. It performs arithmetic and Boolean
functions between data in the working register and any
register file.
The ALU is 8-bits wide and capable of addition,
subtraction, shift and logical operations. Unless
otherwise mentioned, arithmetic operations are two's
complement in nature. In two-operand instructions,
typically one operand is the W (working) register. The
other operand is either a file register or an immediate
constant. In single operand instructions, the operand
is either the W register or a file register.
The W register is an 8-bit working register used for
ALU operations. It is not an addressable register.
Depending on the instruction executed, the ALU may
affect the values of the Carry (C), Digit Carry (DC),
and Zero (Z) bits in the STATUS register. The C and
DC bits operate as a borrow and digit borrow out bit,
respectively, in subtraction. See the SUBWF and ADDWF
instructions for examples.
A simplified block diagram is shown in Figure 3-1, with
the corresponding device pins described in Table 3-1.
The PIC16C5X can directly or indirectly address its
register files and data memory. All special function
registers including the program counter are mapped in
the data memory. The PIC16C5X has a highly
orthogonal (symmetrical) instruction set that makes it
possible to carry out any operation on any register
using any addressing mode. This symmetrical nature
and lack of ‘special optimal situations’ make
programming with the PIC16C5X simple yet efficient.
In addition, the learning curve is reduced significantly.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 9
PIC16C5X
FIGURE 3-1:
PIC16C5X SERIES BLOCK DIAGRAM
9-11
9-11
EPROM/ROM
384 X 12 TO
2048 X 12
T0CKI
PIN
STACK 1
STACK 2
CONFIGURATION WORD
“DISABLE”
“OSC
SELECT”
PC
WATCHDOG
TIMER
12
“CODE
PROTECT”
2
OSCILLATOR/
TIMING &
CONTROL
INSTRUCTION
REGISTER
WDT TIME
OUT
9
12
OSC1 OSC2 MCLR
CLKOUT
WDT/TMR0
PRESCALER
8
“SLEEP”
INSTRUCTION
DECODER
6
“OPTION”
OPTION REG.
DIRECT ADDRESS
DIRECT RAM
ADDRESS
FROM W
5
5-7
LITERALS
8
STATUS
TMR0
GENERAL
PURPOSE
REGISTER
FILE
(SRAM)
24, 25, 72 or
73 Bytes
FSR
8
W
DATA BUS
ALU
8
FROM W
4
4
“TRIS 5”
8
“TRIS 6”
TRISA
PORTA
4
RA3:RA0
DS30453A-page 10
FROM W
Preliminary
TRISB
FROM W
8
PORTB
8
RB7:RB0
8
“TRIS 7”
TRISC
8
PORTC
8
RC7:RC0
(28-Pin
Devices Only)
1997 Microchip Technology Inc.
PIC16C5X
TABLE 3-1:
Name
PINOUT DESCRIPTION - PIC16C52, PIC16C54s, PIC16CR54s, PIC16C56s,
PIC16CR56s, PIC16C58s, PIC16CR58s
DIP, SOIC SSOP I/O/P Input
No.
No. Type Levels
RA0
RA1
RA2
RA3
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
T0CKI
17
18
1
2
6
7
8
9
10
11
12
13
3
19
20
1
2
7
8
9
10
11
12
13
14
3
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
ST
MCLR/VPP
4
4
I
ST
OSC1/CLKIN
OSC2/CLKOUT
16
15
18
17
I
O
ST
—
VDD
14
15,16
P
—
VSS
5
5,6
P
—
Legend: I = input, O = output, I/O = input/output,
P = power, — = Not Used, TTL = TTL input,
ST = Schmitt Trigger input
1997 Microchip Technology Inc.
Description
Bi-directional I/O port
Bi-directional I/O port
Clock input to Timer0. Must be tied to VSS or VDD, if not in
use, to reduce current consumption.
Master clear (reset) input/programming voltage input. This
pin is an active low reset to the device. Voltage on the
MCLR/VPP pin must not exceed VDD to avoid unintended
entering of programming mode.
Oscillator crystal input/external clock source input.
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, OSC2 pin outputs
CLKOUT which has 1/4 the frequency of OSC1, and denotes
the instruction cycle rate.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Preliminary
DS30453A-page 11
PIC16C5X
TABLE 3-2:
Name
PINOUT DESCRIPTION
- PIC16C55s, PIC16C57s, PIC16CR57s
DIP, SOIC SSOP I/O/P Input
No.
No. Type Levels
RA0
RA1
RA2
RA3
RB0
RB1
RB2
RB3
RB4
RB5
RB6
RB7
RC0
RC1
RC2
RC3
RC4
RC5
RC6
RC7
T0CKI
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
2
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
TTL
ST
MCLR
28
28
I
ST
OSC1/CLKIN
OSC2/CLKOUT
27
26
27
26
I
O
ST
—
VDD
2
3,4
P
—
VSS
4
1,14
P
—
N/C
3,5
—
—
—
Legend: I = input, O = output, I/O = input/output,
P = power, — = Not Used,
TTL = TTL input, ST = Schmitt Trigger input
DS30453A-page 12
Description
Bi-directional I/O port
Bi-directional I/O port
Bi-directional I/O port
Clock input to Timer0. Must be tied to VSS or VDD if not in use
to reduce current consumption.
Master clear (reset) input. This pin is an active low reset to the
device.
Oscillator crystal input/external clock source input.
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, OSC2 pin outputs
CLKOUT which has 1/4 the frequency of OSC1, and denotes
the instruction cycle rate.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Unused, do not connect
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
3.1
Clocking Scheme/Instruction Cycle
3.2
The clock input (OSC1/CLKIN pin) is internally divided
by four to generate four non-overlapping quadrature
clocks namely Q1, Q2, Q3 and Q4. Internally, the
program counter is incremented every Q1, and the
instruction is fetched from program memory and
latched into instruction register in Q4. It is decoded
and executed during the following Q1 through Q4. The
clocks and instruction execution flow is shown in
Figure 3-2 and Example 3-1.
Instruction Flow/Pipelining
An Instruction Cycle consists of four Q cycles (Q1, Q2,
Q3 and Q4). The instruction fetch and execute are
pipelined such that fetch takes one instruction cycle
while decode and execute takes another instruction
cycle. However, due to the pipelining, each instruction
effectively executes in one cycle. If an instruction
causes the program counter to change (e.g., GOTO)
then two cycles are required to complete the
instruction (Example 3-1).
A fetch cycle begins with the program counter (PC)
incrementing in Q1.
In the execution cycle, the fetched instruction is
latched into the Instruction Register (IR) in cycle Q1.
This instruction is then decoded and executed during
the Q2, Q3, and Q4 cycles. Data memory is read
during Q2 (operand read) and written during Q4
(destination write).
FIGURE 3-2:
CLOCK/INSTRUCTION CYCLE
Q2
Q1
Q3
Q4
Q2
Q1
Q3
Q4
Q1
Q2
Q3
Q4
OSC1
Q1
Q2
Internal
phase
clock
Q3
Q4
PC
PC
OSC2/CLKOUT
(RC mode)
EXAMPLE 3-1:
PC+1
Fetch INST (PC)
Execute INST (PC-1)
PC+2
Fetch INST (PC+1)
Execute INST (PC)
Fetch INST (PC+2)
Execute INST (PC+1)
INSTRUCTION PIPELINE FLOW
1. MOVLW 55H
2. MOVWF PORTB
3. CALL
SUB_1
4. BSF
PORTA, BIT3
Fetch 1
Execute 1
Fetch 2
Execute 2
Fetch 3
Execute 3
Fetch 4
Flush
Fetch SUB_1 Execute SUB_1
All instructions are single cycle, except for any program branches. These take two cycles since the fetch
instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 13
PIC16C5X
NOTES:
DS30453A-page 14
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
4.0
MEMORY ORGANIZATION
FIGURE 4-2:
PIC16C5X memory is organized into program memory
and data memory. For devices with more than 512
bytes of program memory, a paging scheme is used.
Program memory pages are accessed using one or
two STATUS register bits. For devices with a data
memory register file of more than 32 registers, a
banking scheme is used. Data memory banks are
accessed using the File Selection Register (FSR).
PIC16C54s/CR54s/C55s
PROGRAM MEMORY MAP
AND STACK
PC<8:0>
9
CALL, RETLW
Stack Level 1
Stack Level 2
000h
The PIC16C52 has a 9-bit Program Counter (PC)
capable of addressing a 384 x 12 program memory
space (Figure 4-1). The PIC16C54s, PIC16CR54s and
PIC16C55s have a 9-bit Program Counter (PC)
capable of addressing a 512 x 12 program memory
space (Figure 4-2). The PIC16C56s and PIC16CR56s
have a 10-bit Program Counter (PC) capable of
addressing a 1K x 12 program memory space
(Figure 4-3). The PIC16CR57s, PIC16C58s and
PIC16CR58s have an 11-bit Program Counter capable
of addressing a 2K x 12 program memory space
(Figure 4-4). Accessing a location above the physically
implemented address will cause a wraparound.
User Memory
Space
Program Memory Organization
FIGURE 4-3:
The reset vector for the PIC16C52 is at 17Fh. A NOP
at the reset vector location will cause a restart at
location 000h. The reset vector for the PIC16C54s,
PIC16CR54s and PIC16C55s is at 1FFh. The reset
vector for the PIC16C56s and PIC16CR56s is at
3FFh. The reset vector for the PIC16C57s,
PIC16CR57s, PIC16C58s, and PIC16CR58s is at
7FFh.
FIGURE 4-1:
PIC16C52 PROGRAM
MEMORY MAP AND STACK
PC<8:0>
On-chip
Program
Memory
0FFh
100h
Reset Vector
1FFh
PIC16C56s/CR56s
PROGRAM MEMORY MAP
AND STACK
PC<9:0>
10
CALL, RETLW
Stack Level 1
Stack Level 2
000h
User Memory
Space
4.1
On-chip Program
Memory (Page 0)
0FFh
100h
1FFh
200h
On-chip Program
Memory (Page 1)
2FFh
300h
Reset Vector
3FFh
9
CALL, RETLW
Stack Level 1
Stack Level 2
User Memory
Space
000h
On-chip Program
Memory
Reset Vector
1997 Microchip Technology Inc.
17Fh
Preliminary
DS30453A-page 15
PIC16C5X
FIGURE 4-4:
PIC16C57s/CR57s/C58s/
CR58s PROGRAM MEMORY
MAP AND STACK
PC<10:0>
11
CALL, RETLW
Stack Level 1
Stack Level 2
000h
On-chip Program
Memory (Page 0)
0FFh
100h
User Memory
Space
1FFh
200h
On-chip Program
Memory (Page 1)
2FFh
300h
3FFh
400h
On-chip Program
Memory (Page 2)
4FFh
500h
5FFh
600h
DS30453A-page 16
On-chip Program
Memory (Page 3)
6FFh
700h
Reset Vector
7FFh
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
4.2
Data Memory Organization
FIGURE 4-5:
Data memory is composed of registers, or bytes of
RAM. Therefore, data memory for a device is specified
by its register file. The register file is divided into two
functional groups: special function registers and
general purpose registers.
PIC16C52, PIC16C54s,
PIC16CR54s, PIC16C55s,
PIC16C56s, PIC16CR56s
REGISTER FILE MAP
File Address
The special function registers include the TMR0
register, the Program Counter (PC), the Status
Register, the I/O registers (ports), and the File Select
Register (FSR). In addition, special purpose registers
are used to control the I/O port configuration and
prescaler options.
00h
INDF(1)
01h
TMR0
02h
PCL
03h
STATUS
04h
FSR
The general purpose registers are used for data and
control information under command of the instructions.
05h
PORTA
06h
PORTB
For the PIC16C52, PIC16C54s, PIC16CR54s,
PIC16C56s and PIC16CR56s, the register file is
composed of 7 special function registers and 25
general purpose registers (Figure 4-5).
07h
PORTC(2)
0Fh
10h
General
Purpose
Registers
For the PIC16C55s, the register file is composed of 8
special function registers and 24 general purpose
registers.
For the PIC16C57s and PIC16CR57s, the register file
is composed of 8 special function registers, 24 general
purpose registers and up to 48 additional general
purpose registers that may be addressed using a
banking scheme (Figure 4-6).
1Fh
Note 1:
2:
Not a physical register. See Section 4.7
PIC16C55s only, others are a general
purpose register.
For the PIC16C58s and PIC16CR58s, the register file
is composed of 7 special function registers, 25 general
purpose registers and up to 48 additional general
purpose registers that may be addressed using a
banking scheme (Figure 4-7).
4.2.1
GENERAL PURPOSE REGISTER FILE
The register file is accessed either directly or indirectly
through the file select register FSR (Section 4.7).
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 17
PIC16C5X
FIGURE 4-6:
PIC16C57s/CR57s REGISTER FILE MAP
FSR<6:5>
00
01
10
11
File Address
00h
INDF(1)
01h
TMR0
02h
PCL
03h
STATUS
04h
FSR
05h
PORTA
06h
PORTB
07h
08h
20h
Addresses map back to
addresses in Bank 0.
PORTC
General
Purpose
Registers
0Fh
10h
2Fh
4Fh
6Fh
30h
50h
70h
General
Purpose
Registers
1Fh
General
Purpose
Registers
General
Purpose
Registers
5Fh
3Fh
Bank 0
General
Purpose
Registers
7Fh
Bank 1
Note 1:
FIGURE 4-7:
60h
40h
Bank 2
Bank 3
Not a physical register. See Section 4.7
PIC16C58s/CR58s REGISTER FILE MAP
FSR<6:5>
00
01
10
11
File Address
00h
INDF(1)
01h
TMR0
20h
02h
PCL
03h
STATUS
04h
FSR
05h
PORTA
06h
PORTB
60h
40h
Addresses map back to
addresses in Bank 0.
07h
General
Purpose
Registers
30h
10h
General
Purpose
Registers
General
Purpose
Registers
Bank 0
General
Purpose
Registers
5Fh
Bank 1
Note 1:
6Fh
70h
50h
3Fh
1Fh
DS30453A-page 18
4Fh
2Fh
0Fh
General
Purpose
Registers
7Fh
Bank 2
Bank 3
Not a physical register. See Section 4.7
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
4.2.2
SPECIAL FUNCTION REGISTERS
The Special Function Registers are registers used by
the CPU and peripheral functions to control the
operation of the device (Table 4-1).
TABLE 4-1:
Address
The special registers can be classified into two sets.
The special function registers associated with the
“core” functions are described in this section. Those
related to the operation of the peripheral features are
described in the section for each peripheral feature.
SPECIAL FUNCTION REGISTER SUMMARY
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
N/A
TRIS
I/O control registers (TRISA, TRISB, TRISC)
1111 1111
1111 1111
N/A
OPTION
Contains control bits to configure Timer0 and Timer0/WDT prescaler
--11 1111
--11 1111
00h
INDF
Uses contents of FSR to address data memory (not a physical register)
xxxx xxxx
uuuu uuuu
01h
TMR0
8-bit real-time clock/counter
xxxx xxxx
uuuu uuuu
02h
PCL
Low order 8 bits of PC
1111 1111
1111 1111
03h
STATUS
04h
FSR
05h
PORTA
—
—
—
—
RA3
RA2
RA1
06h
PORTB
RB7
RB6
RB5
RB4
RB3
RB2
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
(1)
(2)
07h
PA2
PA1
PA0
TO
PD
Z
DC
C
0001 1xxx
000q quuu
1xxx xxxx
1uuu uuuu
RA0
---- xxxx
---- uuuu
RB1
RB0
xxxx xxxx
uuuu uuuu
RC1
RC0
xxxx xxxx
uuuu uuuu
Indirect data memory address pointer
Legend: Shaded boxes = unimplemented or unused, – = unimplemented, read as '0' (if applicable)
x = unknown, u = unchanged, q = see the tables in Section 7.7 for possible values.
Note 1: The upper byte of the Program Counter is not directly accessible. See Section 4.5
for an explanation of how to access these bits.
2: File address 07h is a general purpose register on the PIC16C52, PIC16C54s, PIC16CR54s, PIC16C56s, PIC16CR56s,
PIC16C58s and PIC16CR58s.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 19
PIC16C5X
4.3
STATUS Register
This register contains the arithmetic status of the ALU,
the RESET status, and the page preselect bits for
program memories larger than 512 words.
The STATUS register can be the destination for any
instruction, as with any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to
the device logic. Furthermore, the TO and PD bits are
FIGURE 4-8:
R/W-0
PA2
bit7
not writable. Therefore, the result of an instruction with
the STATUS register as destination may be different
than intended.
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as 000u u1uu (where u = unchanged).
It is recommended, therefore, that only BCF, BSF and
MOVWF instructions be used to alter the STATUS
register because these instructions do not affect the Z,
DC or C bits from the STATUS register. For other
instructions, which do affect STATUS bits, see
Section 8.0, Instruction Set Summary.
STATUS REGISTER (ADDRESS:03h)
R/W-0
PA1
6
R/W-0
PA0
5
R-1
TO
4
R-1
PD
3
R/W-x
Z
2
R/W-x
DC
1
R/W-x
C
bit0
R = Readable bit
W = Writable bit
- n = Value at POR reset
bit 7:
PA2: This bit unused at this time.
Use of the PA2 bit as a general purpose read/write bit is not recommended, since this may affect upward
compatibility with future products.
bit 6-5:
PA1:PA0: Program page preselect bits (PIC16C56s/CR56s)(PIC16C57s/CR57s)(PIC16C58s/CR58s)
00 = Page 0 (000h - 1FFh) - PIC16C56s/CR56s, PIC16C57s/CR57s, PIC16C58s/CR58s
01 = Page 1 (200h - 3FFh) - PIC16C56s/CR56s, PIC16C57s/CR57s, PIC16C58s/CR58s
10 = Page 2 (400h - 5FFh) - PIC16C57s/CR57s, PIC16C58s/CR58s
11 = Page 3 (600h - 7FFh) - PIC16C57s/CR57s, PIC16C58s/CR58s
Each page is 512 words.
Using the PA1:PA0 bits as general purpose read/write bits in devices which do not use them for program
page preselect is not recommended since this may affect upward compatibility with future products.
bit 4:
TO: Time-out bit
1 = After power-up, CLRWDT instruction, or SLEEP instruction
0 = A WDT time-out occurred
bit 3:
PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
bit 2:
Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1:
DC: Digit carry/borrow bit (for ADDWF and SUBWF instructions)
ADDWF
1 = A carry from the 4th low order bit of the result occurred
0 = A carry from the 4th low order bit of the result did not occur
SUBWF
1 = A borrow from the 4th low order bit of the result did not occur
0 = A borrow from the 4th low order bit of the result occurred
bit 0:
C: Carry/borrow bit (for ADDWF, SUBWF and RRF, RLF instructions)
ADDWF
SUBWF
1 = A carry occurred
1 = A borrow did not occur
0 = A carry did not occur
0 = A borrow occurred
DS30453A-page 20
Preliminary
RRF or RLF
Load bit with LSb or MSb, respectively
1997 Microchip Technology Inc.
PIC16C5X
4.4
OPTION Register
By executing the OPTION instruction, the contents of
the W register will be transferred to the OPTION
register. A RESET sets the OPTION<5:0> bits.
The OPTION register is a 6-bit wide, write-only
register which contains various control bits to
configure the Timer0/WDT prescaler and Timer0.
FIGURE 4-9:
U-0
—
bit7
OPTION REGISTER
U-0
—
6
W-1
T0CS
5
W-1
T0SE
4
W-1
PSA
3
W-1
PS2
2
W-1
PS1
1
bit 7-6:
Unimplemented.
bit 5:
T0CS: Timer0 clock source select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKOUT)
bit 4:
T0SE: Timer0 source edge select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
bit 3:
PSA: Prescaler assignment bit
1 = Prescaler assigned to the WDT (not implemented on PIC16C52)
0 = Prescaler assigned to Timer0
bit 2-0:
PS2:PS0: Prescaler rate select bits
Bit Value
Timer0 Rate
000
001
010
011
100
101
110
111
1:2
1:4
1:8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
1997 Microchip Technology Inc.
W-1
PS0
bit0
W = Writable bit
U = Unimplemented bit
- n = Value at POR reset
WDT Rate (not implemented on PIC16C52)
1:1
1:2
1:4
1:8
1 : 16
1 : 32
1 : 64
1 : 128
Preliminary
DS30453A-page 21
PIC16C5X
4.5
Program Counter
As a program instruction is executed, the Program
Counter (PC) will contain the address of the next
program instruction to be executed. The PC value is
increased by one every instruction cycle, unless an
instruction changes the PC.
FIGURE 4-10: LOADING OF PC
BRANCH INSTRUCTIONS PIC16C52, PIC16C54s,
PIC16CR54s, PIC16C55s
GOTO Instruction
8
For a GOTO instruction, bits 8:0 of the PC are provided
by the GOTO instruction word. The PC Latch (PCL) is
mapped to PC<7:0> (Figure 4-10 and Figure 4-11).
For the PIC16C56s, PIC16CR56s, PIC16C57s,
PIC16CR57s, PIC16C58s and PIC16CR58s, a page
number must be supplied as well. Bit5 and bit6 of the
STATUS register provide page information to bit9 and
bit10 of the PC (Figure 4-11 and Figure 4-12).
For a CALL instruction, or any instruction where the
PCL is the destination, bits 7:0 of the PC again are
provided by the instruction word. However, PC<8>
does not come from the instruction word, but is always
cleared (Figure 4-10 and Figure 4-11).
Instructions where the PCL is the destination, or
Modify PCL instructions, include MOVWF PC, ADDWF
PC, and BSF PC,5.
For the PIC16C56s, PIC16CR56s, PIC16C57s,
PIC16CR57s, PIC16C58s and PIC16CR58s, a page
number again must be supplied. Bit5 and bit6 of the
STATUS register provide page information to bit9 and
bit10 of the PC (Figure 4-11 and Figure 4-12).
Note:
7
0
PCL
PC
Instruction Word
CALL or Modify PCL Instruction
8
7
0
PCL
PC
Instruction Word
Reset to '0'
FIGURE 4-11: LOADING OF PC
BRANCH INSTRUCTIONS PIC16C56s/PIC16CR56s
GOTO Instruction
10
9
8 7
0
PC
PCL
Instruction Word
Because PC<8> is cleared in the CALL
instruction, or any Modify PCL instruction,
all subroutine calls or computed jumps are
limited to the first 256 locations of any program memory page (512 words long).
2
PA1:PA0
7
0
STATUS
CALL or Modify PCL Instruction
10
9
8 7
0
PC
PCL
Instruction Word
2
Reset to ‘0’
PA1:PA0
7
0
STATUS
DS30453A-page 22
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
FIGURE 4-12: LOADING OF PC
BRANCH INSTRUCTIONS PIC16C57s/PIC16CR57s, AND
PIC16C58s/PIC16CR58s
GOTO Instruction
10
9
8 7
0
PC
PCL
Instruction Word
2
PA1:PA0
7
0
8 7
0
PC
4.5.2
PCL
Reset to ‘0’
PA1:PA0
7
EFFECTS OF RESET
The Program Counter is set upon a RESET, which
means that the PC addresses the last location in the
last page i.e., the reset vector.
Instruction Word
2
If the Program Counter is pointing to the last address
of a selected memory page, when it increments it will
cause the program to continue in the next higher page.
However, the page preselect bits in the STATUS
register will not be updated. Therefore, the next GOTO,
CALL, or Modify PCL instruction will send the program
to the page specified by the page preselect bits (PA0
or PA1:PA0).
To prevent this, the page preselect bits must be
updated under program control.
CALL or Modify PCL Instruction
9
PAGING CONSIDERATIONS –
PIC16C56s/CR56s, PIC16C57s/CR57s AND
PIC16C58s/CR58s
For example, a NOP at location 1FFh (page 0)
increments the PC to 200h (page 1). A GOTO xxx at
200h will return the program to address xxxh on page
0 (assuming that PA1:PA0 are clear).
STATUS
10
4.5.1
The STATUS register page preselect bits are cleared
upon a RESET, which means that page 0 is
pre-selected.
0
STATUS
For the RETLW instruction, the PC is loaded with the
Top Of Stack (TOS) contents. All of the devices
covered in this data sheet have a two-level stack. The
stack has the same bit width as the device PC.
Therefore, upon a RESET, a GOTO instruction at the
reset vector location will automatically cause the
program to jump to page 0.
4.6
Stack
PIC16C5X devices have a 9-bit, 10-bit or 11-bit wide,
two-level hardware push/pop stack (Figure 4-2,
Figure 4-1, and Figure 4-3 respectively).
A CALL instruction will push the current value of stack 1
into stack 2 and then push the current program counter
value, incremented by one, into stack level 1. If more
than two sequential CALL’s are executed, only the most
recent two return addresses are stored.
A RETLW instruction will pop the contents of stack level
1 into the program counter and then copy stack level 2
contents into level 1. If more than two sequential
RETLW’s are executed, the stack will be filled with the
address previously stored in level 2. Note that the
W register will be loaded with the literal value specified
in the instruction. This is particularly useful for the
implementation of data look-up tables within the
program memory.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 23
PIC16C5X
4.7
Indirect Data Addressing; INDF and
FSR Registers
EXAMPLE 4-2:
The INDF register is not a physical register.
Addressing INDF actually addresses the register
whose address is contained in the FSR register (FSR
is a pointer). This is indirect addressing.
EXAMPLE 4-1:
movlw
movwf
clrf
incf
btfsc
goto
NEXT
INDIRECT ADDRESSING
HOW TO CLEAR RAM
USING INDIRECT
ADDRESSING
0x10
FSR
INDF
FSR,F
FSR,4
NEXT
;initialize pointer
; to RAM
;clear INDF register
;inc pointer
;all done?
;NO, clear next
CONTINUE
•
•
•
•
Register file 05 contains the value 10h
Register file 06 contains the value 0Ah
Load the value 05 into the FSR register
A read of the INDF register will return the value
of 10h
• Increment the value of the FSR register by one
(FSR = 06)
• A read of the INDR register now will return the
value of 0Ah.
:
;YES, continue
The FSR is either a 5-bit (PIC16C52, PIC16C54s,
PIC16CR54s,
PIC16C55s),
6-bit
(PIC16C56s,
PIC16CR56s), or 7-bit (PIC16C57s, PIC16CR57s,
PIC16C58s, PIC16CR58s) wide register. It is used in
conjunction with the INDF register to indirectly address
the data memory area.
The FSR<4:0> bits are used to select data memory
addresses 00h to 1Fh.
Reading INDF itself indirectly (FSR = 0) will produce
00h. Writing to the INDF register indirectly results in a
no-operation (although STATUS bits may be affected).
PIC16C52, PIC16C54s, PIC16CR54s, PIC16C55s:
Do not use banking. FSR<6:5> are unimplemented
and read as '1's.
A simple program to clear RAM locations 10h-1Fh
using indirect addressing is shown in Example 4-2.
PIC16C56s, PIC16CR56s: FSR<6:5> are the bank
select bits and are used to select the bank to be
addressed (00 = bank 0, 01 = bank 1, 10 = invalid, 11
= invalid).
PIC16C57s,
PIC16CR57s,
PIC16C58s,
PIC16CR58s: FSR<6:5> are the bank select bits and
are used to select the bank to be addressed (00 =
bank 0, 01 = bank 1, 10 = bank 2, 11 = bank 3).
FIGURE 4-13: DIRECT/INDIRECT ADDRESSING
Direct Addressing
(FSR)
6 5
4
bank select
location select
Indirect Addressing
(opcode)
0
6
5
4
bank
00
01
10
(FSR)
0
location select
11
00h
Addresses map back
to addresses in Bank 0.
Data
Memory(1)
0Fh
10h
1Fh
Bank 0
3Fh
5Fh
Bank 1
7Fh
Bank 2
Bank 3
Note 1: For register map detail see Section 4.2.
DS30453A-page 24
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
5.0
I/O PORTS
5.5
As with any other register, the I/O registers can be
written and read under program control. However, read
instructions (e.g., MOVF PORTB,W) always read the I/O
pins independent of the pin’s input/output modes. On
RESET, all I/O ports are defined as input (inputs are at
hi-impedance) since the I/O control registers (TRISA,
TRISB, TRISC) are all set.
5.1
PORTA
PORTA is a 4-bit I/O register. Only the low order 4 bits
are used (RA3:RA0). Bits 7-4 are unimplemented and
read as '0's.
5.2
The equivalent circuit for an I/O port pin is shown in
Figure 5-1. All ports may be used for both input and
output operation. For input operations these ports are
non-latching. Any input must be present until read by
an input instruction (e.g., MOVF PORTB, W). The
outputs are latched and remain unchanged until the
output latch is rewritten. To use a port pin as output,
the corresponding direction control bit (in TRISA,
TRISB) must be cleared (= 0). For use as an input, the
corresponding TRIS bit must be set. Any I/O pin can
be programmed individually as input or output.
FIGURE 5-1:
Data
Bus
D
PORTC
WR
Port
PORTC is an 8-bit I/O register for PIC16C55s,
PIC16C57s and PIC16CR57s.
PORTC is a general purpose register for PIC16C52,
PIC16C54s, PIC16CR54s, PIC16C56s, PIC16C58s
and PIC16CR58s.
5.4
EQUIVALENT CIRCUIT
FOR A SINGLE I/O PIN
PORTB
PORTB is an 8-bit I/O register (PORTB<7:0>).
5.3
I/O Interfacing
W
Reg
CK
VDD
Q
P
N
D
TRIS ‘f’
The output driver control registers are loaded with the
contents of the W register by executing the TRIS f
instruction. A '1' from a TRIS register bit puts the
corresponding output driver in a hi-impedance mode.
A '0' puts the contents of the output data latch on the
selected pins, enabling the output buffer.
I/O
pin(1)
Q
TRIS
Latch
TRIS Registers
Note:
Q
Data
Latch
CK
VSS
Q
Reset
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
RD Port
Note 1: I/O pins have protection diodes to VDD and VSS.
The TRIS registers are “write-only” and are set (output
drivers disabled) upon RESET.
TABLE 5-1:
Address
SUMMARY OF PORT REGISTERS
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
I/O control registers (TRISA, TRISB)
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
1111 1111
1111 1111
N/A
TRIS
05h
PORTA
—
—
—
—
RA3
RA2
RA1
RA0
---- xxxx
---- uuuu
06h
PORTB
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
xxxx xxxx
uuuu uuuu
07h
PORTC
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
xxxx xxxx
uuuu uuuu
Legend: Shaded boxes = unimplemented, read as ‘0’,
– = unimplemented, read as '0', x = unknown, u = unchanged
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 25
PIC16C5X
5.6
I/O Programming Considerations
5.6.1
BI-DIRECTIONAL I/O PORTS
EXAMPLE 5-1:
;Initial PORT Settings
; PORTB<7:4> Inputs
; PORTB<3:0> Outputs
;PORTB<7:6> have external pull-ups and are
;not connected to other circuitry
;
;
PORT latch PORT pins
;
---------- ---------BCF
PORTB, 7
;01pp pppp
11pp pppp
BCF
PORTB, 6
;10pp pppp
11pp pppp
MOVLW 03Fh
;
TRIS PORTB
;10pp pppp
10pp pppp
;
;Note that the user may have expected the pin
;values to be 00pp pppp. The 2nd BCF caused
;RB7 to be latched as the pin value (High).
Some instructions operate internally as read followed
by write operations. The BCF and BSF instructions, for
example, read the entire port into the CPU, execute
the bit operation and re-write the result. Caution must
be used when these instructions are applied to a port
where one or more pins are used as input/outputs. For
example, a BSF operation on bit5 of PORTB will cause
all eight bits of PORTB to be read into the CPU, bit5 to
be set and the PORTB value to be written to the output
latches. If another bit of PORTB is used as a
bi-directional I/O pin (say bit0) and it is defined as an
input at this time, the input signal present on the pin
itself would be read into the CPU and rewritten to the
data latch of this particular pin, overwriting the
previous content. As long as the pin stays in the input
mode, no problem occurs. However, if bit0 is switched
into output mode later on, the content of the data latch
may now be unknown.
5.6.2
SUCCESSIVE OPERATIONS ON I/O
PORTS
The actual write to an I/O port happens at the end of
an instruction cycle, whereas for reading, the data
must be valid at the beginning of the instruction cycle
(Figure 5-2). Therefore, care must be exercised if a
write followed by a read operation is carried out on the
same I/O port. The sequence of instructions should
allow the pin voltage to stabilize (load dependent)
before the next instruction, which causes that file to be
read into the CPU, is executed. Otherwise, the
previous state of that pin may be read into the CPU
rather than the new state. When in doubt, it is better to
separate these instructions with a NOP or another
instruction not accessing this I/O port.
Example 5-1 shows the effect of two sequential
read-modify-write instructions (e.g., BCF, BSF, etc.) on
an I/O port.
A pin actively outputting a high or a low should not be
driven from external devices at the same time in order
to change the level on this pin (“wired-or”, “wired-and”).
The resulting high output currents may damage the
chip.
FIGURE 5-2:
READ-MODIFY-WRITE
INSTRUCTIONS ON AN
I/O PORT
SUCCESSIVE I/O OPERATION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
Instruction
fetched
MOVWF PORTB
PC + 1
MOVF PORTB,W
PC + 2
PC + 3
NOP
NOP
This example shows a write
to PORTB followed by a read
from PORTB.
RB7:RB0
Port pin
written here
Instruction
executed
DS30453A-page 26
MOVWF PORTB
(Write to
PORTB)
Port pin
sampled here
MOVF PORTB,W
(Read
PORTB)
Preliminary
NOP
1997 Microchip Technology Inc.
PIC16C5X
6.0
TIMER0 MODULE AND
TMR0 REGISTER
Counter mode is selected by setting the T0CS bit
(OPTION<5>). In this mode, Timer0 will increment
either on every rising or falling edge of pin T0CKI. The
incrementing edge is determined by the source edge
select bit T0SE (OPTION<4>). Clearing the T0SE bit
selects the rising edge. Restrictions on the external
clock input are discussed in detail in Section 6.1.
The Timer0 module has the following features:
• 8-bit timer/counter register, TMR0
- Readable and writable
• 8-bit software programmable prescaler
• Internal or external clock select
- Edge select for external clock
The prescaler may be used by either the Timer0
module or the Watchdog Timer, but not both. The
prescaler assignment is controlled in software by the
control bit PSA (OPTION<3>). Clearing the PSA bit
will assign the prescaler to Timer0. The prescaler is
not readable or writable. When the prescaler is
assigned to the Timer0 module, prescale values of 1:2,
1:4,..., 1:256 are selectable. Section 6.2 details the
operation of the prescaler.
Figure 6-1 is a simplified block diagram of the Timer0
module, while Figure 6-2 shows the electrical structure
of the Timer0 input.
Timer mode is selected by clearing the T0CS bit
(OPTION<5>). In timer mode, the Timer0 module will
increment every instruction cycle (without prescaler). If
TMR0 register is written, the increment is inhibited for
the following two cycles (Figure 6-3 and Figure 6-4).
The user can work around this by writing an adjusted
value to the TMR0 register.
FIGURE 6-1:
A summary of registers associated with the Timer0
module is found in Table 6-1.
TIMER0 BLOCK DIAGRAM
Data bus
FOSC/4
0
PSout
1
1
T0CKI
pin
Programmable
Prescaler(2)
T0SE(1)
0
8
Sync with
Internal
Clocks
TMR0 reg
PSout
(2 cycle delay) Sync
3
T0CS(1)
PSA(1)
PS2, PS1, PS0(1)
Note 1: Bits T0CS, T0SE, PSA, PS2, PS1 and PS0 are located in the OPTION register.
2: The prescaler is shared with the Watchdog Timer (Figure 6-6).
FIGURE 6-2:
ELECTRICAL STRUCTURE OF T0CKI PIN
RIN
T0CKI
pin
(1)
VSS
N
(1)
Schmitt Trigger
Input Buffer
VSS
Note 1: ESD protection circuits
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 27
PIC16C5X
FIGURE 6-3:
TIMER0 TIMING: INTERNAL CLOCK/NO PRESCALE
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
Instruction
Fetch
T0
Timer0
PC
PC+1
MOVWF TMR0
MOVF TMR0,W
T0+1
Instruction
Executed
FIGURE 6-4:
PC+3
MOVF TMR0,W
T0+2
NT0
NT0
Write TMR0
executed
Read TMR0
reads NT0
Read TMR0
reads NT0
PC+4
PC+5
MOVF TMR0,W
NT0
NT0+1
Read TMR0
reads NT0 + 1
Read TMR0
reads NT0
PC+6
MOVF TMR0,W
NT0+2
Read TMR0
reads NT0 + 2
TIMER0 TIMING: INTERNAL CLOCK/PRESCALE 1:2
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
PC
(Program
Counter)
PC-1
Instruction
Fetch
PC
PC+1
MOVWF TMR0
MOVF TMR0,W
Instruction
Execute
PC+3
MOVF TMR0,W
PC+4
PC+5
MOVF TMR0,W
Read TMR0
reads NT0
Read TMR0
reads NT0
PC+6
MOVF TMR0,W
NT0+1
NT0
Write TMR0
executed
TABLE 6-1:
PC+2
MOVF TMR0,W
T0+1
T0
Timer0
Address
PC+2
MOVF TMR0,W
Read TMR0
reads NT0
Read TMR0
reads NT0
T0
Read TMR0
reads NT0 + 1
REGISTERS ASSOCIATED WITH TIMER0
Name
01h
TMR0
N/A
OPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Timer0 - 8-bit real-time clock/counter
—
—
T0CS
T0SE
PSA
Value on
Power-On
Reset
Value on
MCLR and
WDT Reset
xxxx xxxx uuuu uuuu
PS2
PS1
PS0
--11 1111 --11 1111
Legend: Shaded cells: Unimplemented bits,
- = unimplemented, x = unknown, u = unchanged,
DS30453A-page 28
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
6.1
Using Timer0 with an External Clock
When a prescaler is used, the external clock input is
divided by the asynchronous ripple counter-type
prescaler so that the prescaler output is symmetrical.
For the external clock to meet the sampling
requirement, the ripple counter must be taken into
account. Therefore, it is necessary for T0CKI to have a
period of at least 4TOSC (and a small RC delay of
40 ns) divided by the prescaler value. The only
requirement on T0CKI high and low time is that they
do not violate the minimum pulse width requirement of
10 ns. Refer to parameters 40, 41 and 42 in the
electrical specification of the desired device.
When an external clock input is used for Timer0, it
must meet certain requirements. The external clock
requirement is due to internal phase clock (TOSC)
synchronization. Also, there is a delay in the actual
incrementing of Timer0 after synchronization.
6.1.1
EXTERNAL CLOCK SYNCHRONIZATION
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI with the internal phase clocks is
accomplished by sampling the prescaler output on the
Q2 and Q4 cycles of the internal phase clocks
(Figure 6-5). Therefore, it is necessary for T0CKI to be
high for at least 2TOSC (and a small RC delay of 20 ns)
and low for at least 2TOSC (and a small RC delay of
20 ns). Refer to the electrical specification of the
desired device.
FIGURE 6-5:
6.1.2
TIMER0 INCREMENT DELAY
Since the prescaler output is synchronized with the
internal clocks, there is a small delay from the time the
external clock edge occurs to the time the Timer0
module is actually incremented. Figure 6-5 shows the
delay from the external clock edge to the timer
incrementing.
TIMER0 TIMING WITH EXTERNAL CLOCK
Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4
External Clock Input or
Prescaler Output (2)
Q1 Q2 Q3 Q4
Small pulse
misses sampling
(1)
External Clock/Prescaler
Output After Sampling
(3)
Increment Timer0 (Q4)
Timer0
T0
T0 + 1
T0 + 2
Note 1: Delay from clock input change to Timer0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc).
Therefore, the error in measuring the interval between two edges on Timer0 input = ± 4Tosc max.
2: External clock if no prescaler selected, Prescaler output otherwise.
3: The arrows indicate the points in time where sampling occurs.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 29
PIC16C5X
6.2
Prescaler
following instruction sequence (Example 6-1) must be
executed when changing the prescaler assignment from
Timer0 to the WDT.
An 8-bit counter is available as a prescaler for the
Timer0 module, or as a postscaler for the Watchdog
Timer (WDT) (WDT postscaler not implemented on
PIC16C52), respectively (Section 6.1.2). For simplicity,
this counter is being referred to as “prescaler”
throughout this data sheet. Note that the prescaler
may be used by either the Timer0 module or the WDT,
but not both. Thus, a prescaler assignment for the
Timer0 module means that there is no prescaler for
the WDT, and vice-versa.
EXAMPLE 6-1:
1.CLRWDT
;Clear WDT
2.CLRF
TMR0
;Clear TMR0 & Prescaler
3.MOVLW '00xx1111’b ;These 3 lines (5, 6, 7)
4.OPTION
; are required only if
; desired
5.CLRWDT
;PS<2:0> are 000 or 001
6.MOVLW '00xx1xxx’b ;Set Postscaler to
7.OPTION
; desired WDT rate
The PSA and PS2:PS0 bits (OPTION<3:0>) determine
prescaler assignment and prescale ratio.
To change prescaler from the WDT to the Timer0
module, use the sequence shown in Example 6-2. This
sequence must be used even if the WDT is disabled. A
CLRWDT instruction should be executed before switching
the prescaler.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF 1, MOVWF 1,
BSF 1,x, etc.) will clear the prescaler. When assigned
to WDT, a CLRWDT instruction will clear the prescaler
along with the WDT. The prescaler is neither readable
nor writable. On a RESET, the prescaler contains all
'0's.
6.2.1
CHANGING PRESCALER
(TIMER0→WDT)
EXAMPLE 6-2:
CHANGING PRESCALER
(WDT→TIMER0)
CLRWDT
SWITCHING PRESCALER ASSIGNMENT
The prescaler assignment is fully under software control
(i.e., it can be changed “on the fly” during program
execution). To avoid an unintended device RESET, the
MOVLW
'xxxx0xxx'
;Clear WDT and
;prescaler
;Select TMR0, new
;prescale value and
;clock source
OPTION
FIGURE 6-6:
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
TCY ( = Fosc/4)
Data Bus
0
T0CKI
pin
1
8
M
U
X
1
M
U
X
0
Sync
2
Cycles
TMR0 reg
T0SE
T0CS
0
Watchdog
Timer
1
M
U
X
PSA
8-bit Prescaler
8
8 - to - 1MUX
PS2:PS0
PSA
WDT Enable bit
1
0
MUX
PSA
WDT
Time-Out
Note: T0CS, T0SE, PSA, PS2:PS0 are bits in the OPTION register.
WDT not implemented on PIC16C52.
DS30453A-page 30
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
7.0
SPECIAL FEATURES OF THE
CPU
The SLEEP mode is designed to offer a very low
current power-down mode. The user can wake up from
SLEEP through external reset or through a Watchdog
Timer time-out. Several oscillator options are also
made available to allow the part to fit the application.
The RC oscillator option saves system cost while the
LP crystal option saves power. A set of configuration
bits are used to select various options.
What sets a microcontroller apart from other
processors are special circuits that deal with the
needs of real-time applications. The PIC16C5X family
of microcontrollers has a host of such features
intended to maximize system reliability, minimize cost
through elimination of external components, provide
power saving operating modes and offer code
protection. These features are:
7.1
Configuration Bits
Configuration bits can be programmed to select
various device configurations. Two bits are for the
selection of the oscillator type and one bit is the
Watchdog Timer enable bit. Nine bits are code
protection bits (Figure 7-1 and Figure 7-2) for the
PIC16C54, PIC16CR54, PIC16C56, PIC16CR56,
PIC16C58, and PIC16CR58 devices.
•
•
•
•
•
Oscillator selection
Reset
Power-On Reset (POR)
Device Reset Timer (DRT)
Watchdog Timer (WDT)
(not implemented on PIC16C52)
• SLEEP
• Code protection
• ID locations (not implemented on PIC16C52)
QTP or ROM devices have the oscillator configuration
programmed at the factory and these parts are tested
accordingly (see "Product Identification System"
diagrams in the back of this data sheet).
The PIC16C5X Family has a Watchdog Timer which
can be shut off only through configuration bit WDTE. It
runs off of its own RC oscillator for added reliability.
There is an 18 ms delay provided by the Device Reset
Timer (DRT), intended to keep the chip in reset until
the crystal oscillator is stable. With this timer on-chip,
most applications need no external reset circuitry.
FIGURE 7-1:
CONFIGURATION WORD FOR
PIC16CR54A/C54B/CR54B/C56A/CR56A/CR57B/C58B/CR58A/CR58B
CP
CP
CP
CP
CP
CP
CP
CP
CP
bit11
10
9
8
7
6
5
4
3
WDTE FOSC1 FOSC0
2
1
bit0
Register:
Address(1):
CONFIG
FFFh
bit 11-3: CP: Code protection bits
1 = Code protection off
0 = Code protection on
bit 2:
WDTE: Watchdog timer enable bit
1 = WDT enabled
0 = WDT disabled
bit 1-0:
FOSC1:FOSC0: Oscillator selection bits
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
Note 1: Refer to the PIC16C5X Programming Specification (Literature Number DS30190) to determine how to access the configuration word.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 31
PIC16C5X
FIGURE 7-2:
CONFIGURATION WORD FOR PIC16C52/C54/C54A/C55/C56/C57/C58A
—
—
—
—
—
—
—
—
CP
bit11
10
9
8
7
6
5
4
3
WDTE FOSC1 FOSC0
2
1
bit0
Register:
Address(1):
CONFIG
FFFh
bit 11-4: Unimplemented: Read as ’0’
bit 3:
CP: Code protection bit.
1 = Code protection off
0 = Code protection on
bit 2:
WDTE: Watchdog timer enable bit (not implemented on PIC16C52)
1 = WDT enabled
0 = WDT disabled
bit 1-0:
FOSC1:FOSC0: Oscillator selection bits(2)
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
Note 1: Refer to the PIC16C5X Programming Specifications (Literature Number DS30190) to
determine how to access the configuration word.
2: PIC16C52 supports XT and RC oscillator only.
PIC16LV54A supports XT, RC and LP oscillator only.
PIC16LV58A supports XT, RC and LP oscillator only.
DS30453A-page 32
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
7.2
Oscillator Configurations
7.2.1
OSCILLATOR TYPES
FIGURE 7-4:
PIC16C5Xs can be operated in four different oscillator
modes. The user can program two configuration bits
(FOSC1:FOSC0) to select one of these four modes:
•
•
•
•
LP:
XT:
HS:
RC:
Low Power Crystal
Crystal/Resonator
High Speed Crystal/Resonator
Resistor/Capacitor
Note:
Not all oscillator selections available for all
parts. See Section 7.1.
7.2.2
EXTERNAL CLOCK INPUT
OPERATION (HS, XT OR LP
OSC CONFIGURATION)
OSC1
PIC16C5X
Clock from
ext. system
Open
TABLE 7-1:
Osc
Type
CRYSTAL OSCILLATOR / CERAMIC
RESONATORS
OSC2
CAPACITOR SELECTION
FOR CERAMIC RESONATORS
- PIC16C5X, PIC16CR5X
Resonator
Freq
Cap. Range
C1
Cap. Range
C2
XT
In XT, LP or HS modes, a crystal or ceramic resonator
is connected to the OSC1/CLKIN and OSC2/CLKOUT
pins to establish oscillation (Figure 7-3). The
PIC16C5X oscillator design requires the use of a
parallel cut crystal. Use of a series cut crystal may give
a frequency out of the crystal manufacturers
specifications. When in XT, LP or HS modes, the
device can have an external clock source drive the
OSC1/CLKIN pin (Figure 7-4).
FIGURE 7-3:
CRYSTAL OPERATION
(OR CERAMIC RESONATOR)
(HS, XT OR LP OSC
CONFIGURATION)
C1(1)
OSC1
PIC16C5X
SLEEP
XTAL
RS(2)
RF(3)
OSC2
To internal
logic
C2(1)
Note 1: See Capacitor Selection tables for
recommended values of C1 and C2.
2: A series resistor (RS) may be required for
AT strip cut crystals.
3: RF varies with the crystal chosen (approx.
value = 10 MΩ).
455 kHz
22-100 pF
22-100 pF
2.0 MHz
15-68 pF
15-68 pF
4.0 MHz
15-68 pF
15-68 pF
HS
4.0 MHz
15-68 pF
15-68 pF
8.0 MHz
10-68 pF
10-68 pF
16.0 MHz
10-22 pF
10-22 pF
These values are for design guidance only. Since
each resonator has its own characteristics, the user
should consult the resonator manufacturer for
appropriate values of external components.
TABLE 7-2:
Osc
Type
Resonator
Freq
Cap.Range
C1
Cap. Range
C2
32 kHz(1)
15 pF
15 pF
100 kHz
15-30 pF
30-47 pF
200 kHz
15-30 pF
15-82 pF
200-300 pF
15-30 pF
XT
100 kHz
100-200 pF
15-30 pF
200 kHz
15-100 pF
15-30 pF
455 kHz
15-30 pF
15-30 pF
1 MHz
15-30 pF
15-30 pF
2 MHz
15-47 pF
15-47 pF
4 MHz
HS
4 MHz
15-30 pF
15-30 pF
8 MHz
15-30 pF
15-30 pF
20 MHz
15-30 pF
15-30 pF
Note 1: For VDD > 4.5V, C1 = C2 ≈ 30 pF is
recommended.
These values are for design guidance only. Rs may
be required in HS mode as well as XT mode to avoid
overdriving crystals with low drive level specification.
Since each crystal has its own characteristics, the
user should consult the crystal manufacturer for
appropriate values of external components.
LP
Note:
1997 Microchip Technology Inc.
CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
- PIC16C5X, PIC16CR5X
Preliminary
If you change from this device to
another device, please verify oscillator
characteristics in your application.
DS30453A-page 33
PIC16C5X
7.2.3
EXTERNAL CRYSTAL OSCILLATOR
CIRCUIT
FIGURE 7-6:
Either a prepackaged oscillator or a simple oscillator
circuit with TTL gates can be used as an external
crystal oscillator circuit. Prepackaged oscillators
provide a wide operating range and better stability. A
well-designed crystal oscillator will provide good
performance with TTL gates. Two types of crystal
oscillator circuits can be used: one with parallel
resonance, or one with series resonance.
Figure 7-5 shows implementation of a parallel
resonant oscillator circuit. The circuit is designed to
use the fundamental frequency of the crystal. The
74AS04 inverter performs the 180-degree phase shift
that a parallel oscillator requires. The 4.7 kΩ resistor
provides the negative feedback for stability. The 10 kΩ
potentiometers bias the 74AS04 in the linear region.
This circuit could be used for external oscillator
designs.
FIGURE 7-5:
EXTERNAL PARALLEL
RESONANT CRYSTAL
OSCILLATOR CIRCUIT
(USING XT, HS OR LP
OSCILLATOR MODE)
+5V
To Other
Devices
10k
74AS04
4.7k
PIC16C5X
CLKIN
74AS04
OSC2
100k
10k
20 pF
Note:
20 pF
If you change from this device to
another device, please verify oscillator
characteristics in your application.
This circuit is also designed to use the fundamental
frequency of the crystal. The inverter performs a
180-degree phase shift in a series resonant oscillator
circuit. The 330 Ω resistors provide the negative
feedback to bias the inverters in their linear region.
DS30453A-page 34
330
To Other
Devices
330
74AS04
74AS04
74AS04
PIC16C5X
CLKIN
0.1 µF
OSC2
XTAL
100k
Note:
7.2.4
If you change from this device to
another device, please verify oscillator
characteristics in your application.
RC OSCILLATOR
For timing insensitive applications, the RC device
option offers additional cost savings. The RC oscillator
frequency is a function of the supply voltage, the
resistor (Rext) and capacitor (Cext) values, and the
operating temperature. In addition to this, the oscillator
frequency will vary from unit to unit due to normal
process parameter variation. Furthermore, the
difference in lead frame capacitance between package
types will also affect the oscillation frequency,
especially for low Cext values. The user also needs to
take into account variation due to tolerance of external
R and C components used.
Figure 7-7 shows how the R/C combination is
connected to the PIC16C5X. For Rext values below
2.2 kΩ, the oscillator operation may become unstable,
or stop completely. For very high Rext values
(e.g., 1 MΩ) the oscillator becomes sensitive to noise,
humidity and leakage. Thus, we recommend keeping
Rext between 3 kΩ and 100 kΩ.
10k
XTAL
EXTERNAL SERIES
RESONANT CRYSTAL
OSCILLATOR CIRCUIT
(USING XT, HS OR LP
OSCILLATOR MODE)
Although the oscillator will operate with no external
capacitor (Cext = 0 pF), we recommend using values
above 20 pF for noise and stability reasons. With no or
small external capacitance, the oscillation frequency
can vary dramatically due to changes in external
capacitances, such as PCB trace capacitance or
package lead frame capacitance.
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
The Electrical Specifications sections show RC
frequency variation from part to part due to normal
process variation.
Also, see the Electrical Specifications sections for
variation of oscillator frequency due to VDD for given
Rext/Cext values as well as frequency variation due to
operating temperature for given R, C, and VDD values.
The oscillator frequency, divided by 4, is available on
the OSC2/CLKOUT pin, and can be used for test
purposes or to synchronize other logic.
FIGURE 7-7:
RC OSCILLATOR MODE
VDD
Rext
OSC1
N
Cext
Internal
clock
PIC16C5X
Fosc/4
OSC2/CLKOUT
If you change from this device to
another device, please verify oscillator
characteristics in your application.
1997 Microchip Technology Inc.
Reset
PIC16C5X devices may be reset in one of the
following ways:
•
•
•
•
•
Power-On Reset (POR)
MCLR reset (normal operation)
MCLR wake-up reset (from SLEEP)
WDT reset (normal operation)
WDT wake-up reset (from SLEEP)
Table 7-3 shows these reset conditions for the PCL
and STATUS registers.
Some registers are not affected in any reset condition.
Their status is unknown on POR and unchanged in
any other reset. Most other registers are reset to a
“reset state” on Power-On Reset (POR), MCLR or
WDT reset. A MCLR or WDT wake-up from SLEEP
also results in a device reset, and not a continuation of
operation before SLEEP.
The TO and PD bits (STATUS <4:3>) are set or
cleared depending on the different reset conditions
(Section 7.7). These bits may be used to determine
the nature of the reset.
VSS
Note:
7.3
Table 7-4 lists a full description of reset states of all
registers. Figure 7-8 shows a simplified block diagram
of the on-chip reset circuit.
Preliminary
DS30453A-page 35
PIC16C5X
TABLE 7-3:
RESET CONDITIONS FOR SPECIAL REGISTERS
PCL
Addr: 02h
STATUS
Addr: 03h
Power-On Reset
1111 1111
0001 1xxx
MCLR reset (normal operation)
1111 1111
000u uuuu(1)
MCLR wake-up (from SLEEP)
1111 1111
0001 0uuu
WDT reset (normal operation)
1111 1111
0000 1uuu(2)
Condition
WDT wake-up (from SLEEP)
1111 1111
Legend: u = unchanged, x = unknown, - = unimplemented read as '0'.
Note 1: TO and PD bits retain their last value until one of the other reset conditions occur.
2: The CLRWDT instruction will set the TO and PD bits.
TABLE 7-4:
0000 0uuu
RESET CONDITIONS FOR ALL REGISTERS
Register
Address
Power-On Reset
MCLR or WDT Reset
W
N/A
xxxx xxxx
uuuu uuuu
TRIS
N/A
1111 1111
1111 1111
OPTION
N/A
--11 1111
--11 1111
INDF
00h
xxxx xxxx
uuuu uuuu
TMR0
01h
xxxx xxxx
uuuu uuuu
PCL(1)
02h
1111 1111
1111 1111
STATUS(1)
03h
0001 1xxx
000q quuu
FSR
04h
1xxx xxxx
1uuu uuuu
PORTA
05h
---- xxxx
---- uuuu
PORTB
06h
xxxx xxxx
uuuu uuuu
PORTC(2)
07h
xxxx xxxx
uuuu uuuu
General Purpose Register Files
07-7Fh
xxxx xxxx
uuuu uuuu
Legend: u = unchanged, x = unknown, - = unimplemented, read as '0',
q = see tables in Section 7.7 for possible values.
Note 1: See Table 7-3 for reset value for specific conditions.
2: General purpose register file on PIC16C52/C54s/CR54s/C56s/CR56s/C58s/CR58s
FIGURE 7-8:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
Power-Up
Detect
POR (Power-On Reset)
VDD
MCLR/VPP pin
WDT Time-out
RESET
WDT
On-Chip
RC OSC
8-bit Asynch
Ripple Counter
(Start-Up Timer)
S
Q
R
Q
CHIP RESET
DS30453A-page 36
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
7.4
Power-On Reset (POR)
FIGURE 7-9:
The PIC16C5X family incorporates on-chip Power-On
Reset (POR) circuitry which provides an internal chip
reset for most power-up situations. To use this feature,
the user merely ties the MCLR/VPP pin to VDD. A
simplified block diagram of the on-chip Power-On
Reset circuit is shown in Figure 7-8.
The Power-On Reset circuit and the Device Reset
Timer (Section 7.5) circuit are closely related. On
power-up, the reset latch is set and the DRT is reset.
The DRT timer begins counting once it detects MCLR
to be high. After the time-out period, which is typically
18 ms, it will reset the reset latch and thus end the
on-chip reset signal.
A power-up example where MCLR is not tied to VDD is
shown in Figure 7-10. VDD is allowed to rise and
stabilize before bringing MCLR high. The chip will
actually come out of reset TDRT msec after MCLR
goes high.
In Figure 7-11, the on-chip Power-On Reset feature is
being used (MCLR and VDD are tied together). The
VDD is stable before the start-up timer times out and
there is no problem in getting a proper reset. However,
Figure 7-12 depicts a problem situation where VDD
rises too slowly. The time between when the DRT
senses a high on the MCLR/VPP pin, and when the
MCLR/VPP pin (and VDD) actually reach their full value,
is too long. In this situation, when the start-up timer
times out, VDD has not reached the VDD (min) value
and the chip is, therefore, not guaranteed to function
correctly. For such situations, we recommend that
external RC circuits be used to achieve longer POR
delay times (Figure 7-9).
Note:
VDD
EXTERNAL POWER-ON
RESET CIRCUIT (FOR SLOW
VDD POWER-UP)
VDD
D
R
R1
MCLR
C
PIC16C5X
• External Power-On Reset circuit is required
only if VDD power-up is too slow. The diode D
helps discharge the capacitor quickly when
VDD powers down.
• R < 40 kΩ is recommended to make sure that
voltage drop across R does not violate the
device electrical specification.
• R1 = 100Ω to 1 kΩ will limit any current
flowing into MCLR from external capacitor C
in the event of MCLR pin breakdown due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
When the device starts normal operation
(exits the reset condition), device operating parameters (voltage, frequency, temperature, etc.) must be meet to ensure
operation. If these conditions are not met,
the device must be held in reset until the
operating conditions are met.
For more information on PIC16C5X POR, see
Power-Up Considerations - AN522 in the Embedded
Control Handbook.
The POR circuit does not produce an internal reset
when VDD declines.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 37
PIC16C5X
FIGURE 7-10: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD)
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
FIGURE 7-11: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): FAST VDD RISE TIME
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
FIGURE 7-12: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): SLOW VDD RISE TIME
V1
VDD
MCLR
INTERNAL POR
TDRT
DRT TIME-OUT
INTERNAL RESET
When VDD rises slowly, the TDRT time-out expires long before VDD has reached its final value. In
this example, the chip will reset properly if, and only if, V1 ≥ VDD min
DS30453A-page 38
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
7.5
Device Reset Timer (DRT)
7.6
The Device Reset Timer (DRT) provides a fixed 18 ms
nominal time-out on reset. The DRT operates on an
internal RC oscillator. The processor is kept in RESET
as long as the DRT is active. The DRT delay allows
VDD to rise above VDD min., and for the oscillator to
stabilize.
Oscillator circuits based on crystals or ceramic
resonators require a certain time after power-up to
establish a stable oscillation. The on-chip DRT keeps
the device in a RESET condition for approximately 18
ms after the voltage on the MCLR/VPP pin has
reached a logic high (VIH) level. Thus, external RC
networks connected to the MCLR input are not
required in most cases, allowing for savings in
cost-sensitive and/or space restricted applications.
The Device Reset time delay will vary from chip to chip
due to VDD, temperature, and process variation. See
AC parameters for details.
The DRT will also be triggered upon a Watchdog Timer
time-out. This is particularly important for applications
using the WDT to wake the PIC16C5X from SLEEP
mode automatically.
Watchdog Timer (WDT) (not
implemented on PIC16C52)
The Watchdog Timer (WDT) is a free running on-chip
RC oscillator which does not require any external
components. This RC oscillator is separate from the
RC oscillator of the OSC1/CLKIN pin. That means that
the WDT will run even if the clock on the OSC1/CLKIN
and OSC2/CLKOUT pins have been stopped, for
example, by execution of a SLEEP instruction. During
normal operation or SLEEP, a WDT reset or wake-up
reset generates a device RESET.
The TO bit (STATUS<4>) will be cleared upon a
Watchdog Timer reset.
The WDT can be permanently disabled by
programming the configuration bit WDTE as a '0'
(Section 7.1). Refer to the PIC16C5X Programming
Specifications (Literature Number DS30190) to
determine how to access the configuration word.
7.6.1
WDT PERIOD
The WDT has a nominal time-out period of 18 ms,
(with no prescaler). If a longer time-out period is
desired, a prescaler with a division ratio of up to 1:128
can be assigned to the WDT (under software control)
by writing to the OPTION register. Thus, time-out a
period of a nominal 2.3 seconds can be realized.
These periods vary with temperature, VDD and
part-to-part process variations (see DC specs).
Under worst case conditions (VDD = Min., Temperature
= Max., max. WDT prescaler), it may take several
seconds before a WDT time-out occurs.
7.6.2
WDT PROGRAMMING CONSIDERATIONS
The CLRWDT instruction clears the WDT and the
postscaler, if assigned to the WDT, and prevents it
from timing out and generating a device RESET.
The SLEEP instruction resets the WDT and the
postscaler, if assigned to the WDT. This gives the
maximum SLEEP time before a WDT wake-up reset.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 39
PIC16C5X
FIGURE 7-13: WATCHDOG TIMER BLOCK DIAGRAM
From TMR0 Clock Source
0
M
U
X
1
Watchdog
Timer
Postscaler
Postscaler
8 - to - 1 MUX
PS2:PS0
PSA
WDT Enable
EPROM Bit
To TMR0
1
0
MUX
PSA
Note: T0CS, T0SE, PSA, PS2:PS0
are bits in the OPTION register.
WDT
Time-out
TABLE 7-5:
Address
N/A
SUMMARY OF REGISTERS ASSOCIATED WITH THE WATCHDOG TIMER
Name
OPTION
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Value on
Power-On
Reset
—
—
T0CS
T0SE
PSA
PS2
PS1
PS0
--11 1111
Value on
MCLR and
WDT Reset
--11 1111
Legend: Shaded boxes = Not used by Watchdog Timer,
– = unimplemented, read as '0', u = unchanged
DS30453A-page 40
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
7.7
Time-Out Sequence and Power Down
Status Bits (TO/PD)
The TO and PD bits in the STATUS register can be
tested to determine if a RESET condition has been
caused by a power-up condition, a MCLR or Watchdog
Timer (WDT) reset, or a MCLR or WDT wake-up reset.
TABLE 7-6:
TO/PD STATUS AFTER
RESET
7.8
Reset on Brown-Out
A brown-out is a condition where device power (VDD)
dips below its minimum value, but not to zero, and then
recovers. The device should be reset in the event of a
brown-out.
To reset PIC16C5X devices when a brown-out occurs,
external brown-out protection circuits may be built, as
shown in Figure 7-14 and Figure 7-15.
FIGURE 7-14: BROWN-OUT PROTECTION
CIRCUIT 1
TO
PD
RESET was caused by
1
1
Power-up (POR)
u
u
1
0
0
1
0
0
MCLR reset (normal operation)(1)
MCLR wake-up reset (from SLEEP)
WDT reset (normal operation)
WDT wake-up reset (from SLEEP)
VDD
VDD
33k
Legend: u = unchanged
Note 1: The TO and PD bits maintain their status (u) until
a reset occurs. A low-pulse on the MCLR input
does not change the TO and PD status bits.
10k
Q1
MCLR
40k
PIC16C5X
These STATUS bits are only affected by events listed
in Table 7-7.
TABLE 7-7:
EVENTS AFFECTING TO/PD
STATUS BITS
Event
Power-up
WDT Time-out
SLEEP instruction
CLRWDT instruction
TO
PD
1
1
0
u
1
0
1
1
This circuit will activate reset when VDD goes below Vz +
0.7V (where Vz = Zener voltage).
Remarks
No effect on PD
FIGURE 7-15: BROWN-OUT PROTECTION
CIRCUIT 2
VDD
Legend: u = unchanged
A WDT time-out will occur regardless of the status of the TO
bit. A SLEEP instruction will be executed, regardless of the
status of the PD bit. Table 7-6 reflects the status of TO and
PD after the corresponding event.
VDD
R1
Q1
MCLR
R2
Table 7-3 lists the reset conditions for the special
function registers, while Table 7-4 lists the reset
conditions for all the registers.
40k
PIC16C5X
This brown-out circuit is less expensive, although
less accurate. Transistor Q1 turns off when VDD
is below a certain level such that:
VDD •
1997 Microchip Technology Inc.
Preliminary
R1
R1 + R2
= 0.7V
DS30453A-page 41
PIC16C5X
7.9
Power-Down Mode (SLEEP)
7.10
A device may be powered down (SLEEP) and later
powered up (Wake-up from SLEEP).
7.9.1
SLEEP
If the code protection bit(s) have not been
programmed, the on-chip program memory can be
read out for verification purposes.
Note:
The Power-Down mode is entered by executing a
SLEEP instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the TO bit (STATUS<4>) is set, the PD
bit (STATUS<3>) is cleared and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, driving low, or hi-impedance).
It should be noted that a RESET generated by a WDT
time-out does not drive the MCLR/VPP pin low.
For lowest current consumption while powered down,
the T0CKI input should be at VDD or VSS and the
MCLR/VPP pin must be at a logic high level
(VIH MCLR).
7.9.2
Program Verification/Code Protection
7.11
Microchip does not recommend code protecting windowed devices.
ID Locations (not implemented on
PIC16C52)
Four memory locations are designated as ID locations
where the user can store checksum or other
code-identification numbers. These locations are not
accessible during normal execution but are readable
and writable during program/verify.
Use only the lower 4 bits of the ID locations and
always program the upper 8 bits as '1's.
Note:
WAKE-UP FROM SLEEP
Microchip will assign a unique pattern
number for QTP and SQTP requests and
for ROM devices. This pattern number will
be unique and traceable to the submitted
code.
The device can wake up from SLEEP through one of
the following events:
1.
2.
An external reset input on MCLR/VPP pin.
A Watchdog Timer time-out reset (if WDT was
enabled).
Both of these events cause a device reset. The TO and
PD bits can be used to determine the cause of device
reset.
The TO bit is cleared if a WDT time-out
occurred (and caused wake-up). The PD bit, which is
set on power-up, is cleared when SLEEP is invoked.
The WDT is cleared when the device wakes from
sleep, regardless of the wake-up source.
DS30453A-page 42
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
8.0
INSTRUCTION SET SUMMARY
Each PIC16C5X instruction is a 12-bit word divided into an
OPCODE, which specifies the instruction type, and one or
more operands which further specify the operation of the
instruction. The PIC16C5X instruction set summary in
Table 8-2 groups the instructions into byte-oriented,
bit-oriented, and literal and control operations. Table 8-1
shows the opcode field descriptions.
For byte-oriented instructions, 'f' represents a file register
designator and 'd' represents a destination designator. The
file register designator is used to specify which one of the
32 file registers is to be used by the instruction.
All instructions are executed within one single
instruction cycle, unless a conditional test is true or the
program counter is changed as a result of an
instruction. In this case, the execution takes two
instruction cycles. One instruction cycle consists of
four oscillator periods. Thus, for an oscillator frequency
of 4 MHz, the normal instruction execution time is 1 µs.
If a conditional test is true or the program counter is
changed as a result of an instruction, the instruction
execution time is 2 µs.
Figure 8-1 shows the three general formats that the
instructions can have. All examples in the figure use the
following format to represent a hexadecimal number:
The destination designator specifies where the result
of the operation is to be placed. If 'd' is '0', the result is
placed in the W register. If 'd' is '1', the result is placed
in the file register specified in the instruction.
where 'h' signifies a hexadecimal digit.
For bit-oriented instructions, 'b' represents a bit field
designator which selects the number of the bit affected
by the operation, while 'f' represents the number of the
file in which the bit is located.
Byte-oriented file register operations
0xhhh
FIGURE 8-1:
11
OPCODE FIELD
DESCRIPTIONS
Field
11
OPCODE
x
Don't care location (= 0 or 1)
The assembler will generate code with x = 0. It is
the recommended form of use for compatibility
with all Microchip software tools.
dest
[ ]
( )
→
<>
∈
italics
4
0
f (FILE #)
d = 0 for destination W
d = 1 for destination f
f = 5-bit file register address
Description
Register file address (0x00 to 0x7F)
Working register (accumulator)
Bit address within an 8-bit file register
Literal field, constant data or label
label
TOS
PC
WDT
TO
PD
5
d
Bit-oriented file register operations
f
W
b
k
d
6
OPCODE
For literal and control operations, 'k' represents an
8 or 9-bit constant or literal value.
TABLE 8-1:
GENERAL FORMAT FOR
INSTRUCTIONS
8 7
5 4
b (BIT #)
f (FILE #)
0
b = 3-bit bit address
f = 5-bit file register address
Literal and control operations (except GOTO)
Destination select;
d = 0 (store result in W)
d = 1 (store result in file register 'f')
Default is d = 1
Label name
Top of Stack
Program Counter
Watchdog Timer Counter
Time-Out bit
Power-Down bit
Destination, either the W register or the specified
register file location
11
8
7
OPCODE
0
k (literal)
k = 8-bit immediate value
Literal and control operations - GOTO instruction
11
9
8
OPCODE
0
k (literal)
k = 9-bit immediate value
Options
Contents
Assigned to
Register bit field
In the set of
User defined term (font is courier)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 43
PIC16C5X
TABLE 8-2:
INSTRUCTION SET SUMMARY
Mnemonic,
Operands
ADDWF
ANDWF
CLRF
CLRW
COMF
DECF
DECFSZ
INCF
INCFSZ
IORWF
MOVF
MOVWF
NOP
RLF
RRF
SUBWF
SWAPF
XORWF
f,d
f,d
f
–
f, d
f, d
f, d
f, d
f, d
f, d
f, d
f
–
f, d
f, d
f, d
f, d
f, d
12-Bit Opcode
Description
Cycles MSb
Add W and f
AND W with f
Clear f
Clear W
Complement f
Decrement f
Decrement f, Skip if 0
Increment f
Increment f, Skip if 0
Inclusive OR W with f
Move f
Move W to f
No Operation
Rotate left f through Carry
Rotate right f through Carry
Subtract W from f
Swap f
Exclusive OR W with f
LSb
Status
Affected Notes
1
1
1
1
1
1
1(2)
1
1(2)
1
1
1
1
1
1
1
1
1
0001
0001
0000
0000
0010
0000
0010
0010
0011
0001
0010
0000
0000
0011
0011
0000
0011
0001
11df
01df
011f
0100
01df
11df
11df
10df
11df
00df
00df
001f
0000
01df
00df
10df
10df
10df
ffff
ffff
ffff
0000
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
0000
ffff
ffff
ffff
ffff
ffff
C,DC,Z
Z
Z
Z
Z
Z
None
Z
None
Z
Z
None
None
C
C
C,DC,Z
None
Z
1,2,4
2,4
4
1
1
1 (2)
1 (2)
0100
0101
0110
0111
bbbf
bbbf
bbbf
bbbf
ffff
ffff
ffff
ffff
None
None
None
None
2,4
2,4
1
2
1
2
1
1
1
2
1
1
1
1110
1001
0000
101k
1101
1100
0000
1000
0000
0000
1111
kkkk
kkkk
0000
kkkk
kkkk
kkkk
0000
kkkk
0000
0000
kkkk
kkkk
kkkk
0100
kkkk
kkkk
kkkk
0010
kkkk
0011
0fff
kkkk
Z
None
TO, PD
None
Z
None
None
None
TO, PD
None
Z
2,4
2,4
2,4
2,4
2,4
2,4
1,4
2,4
2,4
1,2,4
2,4
2,4
BIT-ORIENTED FILE REGISTER OPERATIONS
BCF
BSF
BTFSC
BTFSS
f, b
f, b
f, b
f, b
Bit Clear f
Bit Set f
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
LITERAL AND CONTROL OPERATIONS
ANDLW
CALL
CLRWDT
GOTO
IORLW
MOVLW
OPTION
RETLW
SLEEP
TRIS
XORLW
k
k
k
k
k
k
k
k
–
f
k
AND literal with W
Call subroutine
Clear Watchdog Timer
Unconditional branch
Inclusive OR Literal with W
Move Literal to W
Load OPTION register
Return, place Literal in W
Go into standby mode
Load TRIS register
Exclusive OR Literal to W
1
3
Note 1: The 9th bit of the program counter will be forced to a '0' by any instruction that writes to the PC except for GOTO.
(See individual device data sheets, Memory Section/Indirect Data Addressing, INDF and FSR Registers)
2: When an I/O register is modified as a function of itself (e.g. MOVF PORTB, 1), the value used will be that value
present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven
low by an external device, the data will be written back with a '0'.
3: The instruction TRIS f, where f = 5 or 6 causes the contents of the W register to be written to the tristate
latches of PORTA or B respectively. A '1' forces the pin to a hi-impedance state and disables the output buffers.
4: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared
(if assigned to TMR0).
DS30453A-page 44
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
ADDWF
Add W and f
Syntax:
[ label ] ADDWF
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(W) + (f) → (dest)
f,d
Status Affected: C, DC, Z
Encoding:
0001
ANDWF
AND W with f
Syntax:
[ label ] ANDWF
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(W) .AND. (f) → (dest)
f,d
Status Affected: Z
11df
Encoding:
ffff
0001
01df
ffff
Description:
Add the contents of the W register and
register 'f'. If 'd' is 0 the result is stored
in the W register. If 'd' is '1' the result is
stored back in register 'f'.
Description:
The contents of the W register are
AND’ed with register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
'1' the result is stored back in register 'f'.
Words:
1
Words:
1
Cycles:
1
Cycles:
1
Example:
ADDWF
Example:
ANDWF
FSR, 0
Before Instruction
W
=
FSR =
W =
FSR =
0x17
0xC2
After Instruction
After Instruction
W
=
FSR =
W
=
FSR =
0xD9
0xC2
ANDLW
And literal with W
Syntax:
[ label ] ANDLW
Operands:
0 ≤ k ≤ 255
Operation:
(W).AND. (k) → (W)
k
Status Affected: Z
1110
Description:
kkkk
1
Cycles:
1
Example:
ANDLW
BCF
Bit Clear f
Syntax:
[ label ] BCF
Operands:
0 ≤ f ≤ 31
0≤b≤7
Operation:
0 → (f<b>)
Encoding:
=
=
0100
bbbf
ffff
Bit 'b' in register 'f' is cleared.
Words:
1
Cycles:
1
Example:
BCF
0x5F
FLAG_REG,
7
Before Instruction
FLAG_REG = 0xC7
0xA3
After Instruction
After Instruction
W
f,b
Description:
Before Instruction
W
0x17
0x02
Status Affected: None
kkkk
The contents of the W register are
AND’ed with the eight-bit literal 'k'. The
result is placed in the W register.
Words:
1
Before Instruction
0x17
0xC2
Encoding:
FSR,
FLAG_REG = 0x47
0x03
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 45
PIC16C5X
BSF
Bit Set f
Syntax:
[ label ] BSF
Operands:
0 ≤ f ≤ 31
0≤b≤7
Operation:
1 → (f<b>)
f,b
Status Affected: None
Encoding:
BTFSS
Bit Test f, Skip if Set
Syntax:
[ label ] BTFSS f,b
Operands:
0 ≤ f ≤ 31
0≤b<7
Operation:
skip if (f<b>) = 1
Status Affected: None
0101
bbbf
Encoding:
ffff
Description:
Bit 'b' in register 'f' is set.
Words:
1
Cycles:
1
Example:
BSF
FLAG_REG,
FLAG_REG = 0x8A
Words:
1
Cycles:
1(2)
Example:
HERE
FALSE
TRUE
BTFSC
Bit Test f, Skip if Clear
Syntax:
[ label ] BTFSC f,b
Operands:
0 ≤ f ≤ 31
0≤b≤7
Before Instruction
skip if (f<b>) = 0
After Instruction
Operation:
•
•
PC
Status Affected: None
Encoding:
0110
bbbf
ffff
Description:
If bit 'b' in register 'f' is 0 then the next
instruction is skipped.
If bit 'b' is 0 then the next instruction
fetched during the current instruction
execution is discarded, and an NOP is
executed instead, making this a 2 cycle
instruction.
Words:
1
Cycles:
1(2)
Example:
HERE
FALSE
TRUE
BTFSC
GOTO
ffff
If bit 'b' in register 'f' is '1' then the next
instruction is skipped.
If bit 'b' is '1', then the next instruction
fetched during the current instruction
execution, is discarded and an NOP is
executed instead, making this a 2 cycle
instruction.
Before Instruction
FLAG_REG = 0x0A
bbbf
Description:
7
After Instruction
0111
If FLAG<1>
PC
if FLAG<1>
PC
BTFSS
GOTO
•
FLAG,1
PROCESS_CODE
=
address (HERE)
=
=
=
=
0,
address (FALSE);
1,
address (TRUE)
FLAG,1
PROCESS_CODE
•
•
•
Before Instruction
PC
=
address (HERE)
=
=
=
=
0,
address (TRUE);
1,
address(FALSE)
After Instruction
if FLAG<1>
PC
if FLAG<1>
PC
DS30453A-page 46
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
CALL
Subroutine Call
CLRW
Clear W
Syntax:
Operands:
[ label ] CALL k
Syntax:
[ label ] CLRW
0 ≤ k ≤ 255
Operands:
None
Operation:
(PC) + 1→ Top of Stack;
k → PC<7:0>;
(STATUS<6:5>) → PC<10:9>;
0 → PC<8>
Operation:
00h → (W);
1→Z
Status Affected: Z
Encoding:
Status Affected: None
Encoding:
Description:
1001
kkkk
kkkk
Subroutine call. First, return address
(PC+1) is pushed onto the stack. The
eight bit immediate address is loaded
into PC bits <7:0>. The upper bits
PC<10:9> are loaded from STATUS<6:5>, PC<8> is cleared. CALL is
a two cycle instruction.
1
Cycles:
2
Example:
HERE
CALL
The W register is cleared. Zero bit (Z)
is set.
Words:
1
Cycles:
1
Example:
CLRW
Before Instruction
W
After Instruction
address (THERE)
address (HERE + 1)
CLRF
Clear f
Syntax:
[ label ] CLRF
Operands:
0 ≤ f ≤ 31
Operation:
00h → (f);
1→Z
0x5A
0000
f
1
Cycles:
1
Example:
CLRF
Clear Watchdog Timer
Syntax:
[ label ] CLRWDT
Operands:
None
Operation:
00h → WDT;
0 → WDT prescaler (if assigned);
1 → TO;
1 → PD
Encoding:
Description:
011f
ffff
0x5A
1
1
Example:
CLRWDT
=
=
0x00
1
1997 Microchip Technology Inc.
0100
Before Instruction
WDT counter =
?
After Instruction
WDT counter
WDT prescale
TO
PD
After Instruction
FLAG_REG
Z
0000
The CLRWDT instruction resets the
WDT. It also resets the prescaler, if the
prescaler is assigned to the WDT and
not Timer0. Status bits TO and PD are
set.
Cycles:
FLAG_REG
=
0000
Words:
Before Instruction
FLAG_REG
0x00
1
Status Affected: TO, PD
The contents of register 'f' are cleared
and the Z bit is set.
Words:
=
=
CLRWDT
Status Affected: Z
Description:
=
THERE
address (HERE)
Encoding:
0000
Description:
W
Z
Before Instruction
PC =
TOS =
0100
After Instruction
Words:
PC =
0000
Preliminary
=
=
=
=
0x00
0
1
1
DS30453A-page 47
PIC16C5X
COMF
Complement f
Syntax:
[ label ] COMF
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) → (dest)
f,d
Status Affected: Z
Encoding:
01df
Words:
1
Cycles:
1
Example:
COMF
0x13
After Instruction
=
=
[ label ] DECFSZ f,d
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) – 1 → d;
Description:
REG1,0
Before Instruction
REG1
W
Syntax:
Encoding:
ffff
The contents of register 'f' are complemented. If 'd' is 0 the result is stored in
the W register. If 'd' is 1 the result is
stored back in register 'f'.
=
Decrement f, Skip if 0
Decrement f
Syntax:
[ label ] DECF f,d
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) – 1 → (dest)
Description:
1
Cycles:
1
Example:
DECF
Before Instruction
CNT
Z
=
=
1
1(2)
Example:
HERE
=
=
DECFSZ
GOTO
CONTINUE •
•
•
CNT, 1
LOOP
PC
=
address (HERE)
After Instruction
CNT
if CNT
PC
if CNT
PC
11df
CNT,
=
=
=
≠
=
CNT - 1;
0,
address (CONTINUE);
0,
address (HERE+1)
ffff
GOTO
Unconditional Branch
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 511
Operation:
k → PC<8:0>;
STATUS<6:5> → PC<10:9>
1
GOTO k
Status Affected: None
0x01
0
After Instruction
CNT
Z
ffff
Before Instruction
Decrement register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Words:
11df
The contents of register 'f' are decremented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
If the result is 0, the next instruction,
which is already fetched, is discarded
and an NOP is executed instead making it a two cycle instruction.
Cycles:
Status Affected: Z
0000
0010
Words:
0x13
0xEC
DECF
Encoding:
skip if result = 0
Status Affected: None
0010
Description:
REG1
DECFSZ
Encoding:
101k
kkkk
kkkk
Description:
GOTO is an unconditional branch. The
9-bit immediate value is loaded into PC
bits <8:0>. The upper bits of PC are
loaded from STATUS<6:5>. GOTO is a
two cycle instruction.
Words:
1
Cycles:
2
Example:
GOTO THERE
0x00
1
After Instruction
PC =
DS30453A-page 48
Preliminary
address (THERE)
1997 Microchip Technology Inc.
PIC16C5X
INCF
Increment f
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) + 1 → (dest)
INCF f,d
Description:
Words:
Inclusive OR literal with W
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 255
Operation:
(W) .OR. (k) → (W)
Encoding:
0010
10df
ffff
The contents of register 'f' are incremented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
1
Cycles:
1
Example:
INCF
CNT,
=
=
1101
kkkk
kkkk
Description:
The contents of the W register are
OR’ed with the eight bit literal 'k'. The
result is placed in the W register.
Words:
1
Cycles:
1
Example:
IORLW
0x35
Before Instruction
1
W
Before Instruction
CNT
Z
IORLW k
Status Affected: Z
Status Affected: Z
Encoding:
IORLW
=
0x9A
After Instruction
0xFF
0
W
Z
=
=
0xBF
0
After Instruction
CNT
Z
=
=
0x00
1
IORWF
Inclusive OR W with f
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
(W).OR. (f) → (dest)
INCFSZ
Increment f, Skip if 0
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) + 1 → (dest), skip if result = 0
Encoding:
Operation:
INCFSZ f,d
Description:
0011
f,d
Status Affected: Z
Status Affected: None
Encoding:
IORWF
11df
00df
ffff
Description:
Inclusive OR the W register with register 'f'. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
Words:
1
Cycles:
1
Example:
IORWF
ffff
The contents of register 'f' are incremented. If 'd' is 0 the result is placed in
the W register. If 'd' is 1 the result is
placed back in register 'f'.
If the result is 0, then the next instruction, which is already fetched, is discarded and an NOP is executed
instead making it a two cycle instruction.
0001
RESULT, 0
Before Instruction
RESULT =
W
=
0x13
0x91
After Instruction
Words:
1
Cycles:
1(2)
Example:
HERE
INCFSZ
GOTO
CONTINUE •
•
•
CNT,
LOOP
1
RESULT =
W
=
Z
=
0x13
0x93
0
Before Instruction
PC
=
address (HERE)
After Instruction
CNT
if CNT
PC
if CNT
PC
=
=
=
≠
=
CNT + 1;
0,
address (CONTINUE);
0,
address (HERE +1)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 49
PIC16C5X
MOVF
Move f
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) → (dest)
MOVF f,d
0010
Description:
Move W to f
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
Operation:
(W) → (f)
Encoding:
00df
ffff
Description:
The contents of register 'f' is moved to
destination 'd'. If 'd' is 0, destination is
the W register. If 'd' is 1, the destination
is file register 'f'. 'd' is 1 is useful to test
a file register since status flag Z is
affected.
1
Cycles:
1
Example:
MOVF
0000
001f
1
Cycles:
1
Example:
MOVWF
TEMP_REG
W
FSR,
TEMP_REG
=
=
0xFF
0x4F
=
=
0x4F
0x4F
After Instruction
0
TEMP_REG
W
value in FSR register
NOP
No Operation
MOVLW
Move Literal to W
Syntax:
[ label ]
Syntax:
[ label ]
Operands:
None
Operands:
0 ≤ k ≤ 255
Operation:
No operation
Operation:
k → (W)
Status Affected: None
MOVLW k
Status Affected: None
Encoding:
1100
Description:
ffff
Move data from the W register to register 'f'.
Words:
After Instruction
=
f
Before Instruction
Words:
W
MOVWF
Status Affected: None
Status Affected: Z
Encoding:
MOVWF
Encoding:
kkkk
Description:
kkkk
0000
NOP
0000
0000
No operation.
The eight bit literal 'k' is loaded into the
W register. The don’t cares will assemble as 0s.
Words:
1
Cycles:
1
Words:
1
Example:
NOP
Cycles:
1
Example:
MOVLW
0x5A
After Instruction
W
=
DS30453A-page 50
0x5A
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
OPTION
Load OPTION Register
RLF
Rotate Left f through Carry
Syntax:
[ label ]
Syntax:
[ label ] RLF
Operands:
None
Operands:
Operation:
(W) → OPTION
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
See description below
OPTION
Status Affected: None
Encoding:
0000
0000
0010
Status Affected: C
Description:
The content of the W register is loaded
into the OPTION register.
Words:
1
Cycles:
1
Example
Encoding:
Description:
OPTION
0011
=
After Instruction
0x07
RETLW
Return with Literal in W
Syntax:
[ label ]
Operands:
0 ≤ k ≤ 255
Operation:
k → (W);
TOS → PC
Words:
1
Cycles:
1
Example:
RLF
1000
Description:
kkkk
REG1
C
REG1
W
C
1
Cycles:
2
Example:
CALL TABLE ;W contains
;table offset
;value.
•
;W now has table
•
;value.
•
ADDWF PC
;W = offset
RETLW k1
;Begin table
RETLW k2
;
•
•
•
RETLW kn
; End of table
W
=
=
=
=
=
1110 0110
1100 1100
1
RRF
Rotate Right f through Carry
Syntax:
[ label ]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
See description below
RRF f,d
Status Affected: C
Encoding:
Description:
0011
00df
ffff
The contents of register 'f' are rotated
one bit to the right through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is placed
back in register 'f'.
C
Words:
1
Cycles:
1
Example:
RRF
register 'f'
REG1,0
Before Instruction
0x07
REG1
C
After Instruction
W
1110 0110
0
kkkk
Words:
Before Instruction
=
=
After Instruction
The W register is loaded with the eight
bit literal 'k'. The program counter is
loaded from the top of the stack (the
return address). This is a two cycle
instruction.
TABLE
REG1,0
Before Instruction
RETLW k
Status Affected: None
Encoding:
ffff
register 'f'
C
0x07
OPTION =
01df
The contents of register 'f' are rotated
one bit to the left through the Carry
Flag. If 'd' is 0 the result is placed in the
W register. If 'd' is 1 the result is stored
back in register 'f'.
Before Instruction
W
f,d
value of k8
=
=
1110 0110
0
After Instruction
REG1
W
C
1997 Microchip Technology Inc.
Preliminary
=
=
=
1110 0110
0111 0011
0
DS30453A-page 51
PIC16C5X
SLEEP
Enter SLEEP Mode
SUBWF
Subtract W from f
Syntax:
[label]
Syntax:
[label]
Operands:
None
Operands:
Operation:
00h → WDT;
0 → WDT prescaler;
1 → TO;
0 → PD
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(f) – (W) → (dest)
SLEEP
Status Affected: C, DC, Z
Encoding:
Status Affected: TO, PD
Encoding:
Description:
0000
Description:
0000
0011
Time-out status bit (TO) is set. The
power down status bit (PD) is cleared.
The WDT and its prescaler are
cleared.
The processor is put into SLEEP mode
with the oscillator stopped. See section on SLEEP for more details.
Words:
1
Cycles:
1
Example:
SLEEP
SUBWF f,d
0000
10df
ffff
Subtract (2’s complement method) the
W register from register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
Words:
1
Cycles:
1
Example 1:
SUBWF
REG1, 1
Before Instruction
REG1
W
C
=
=
=
3
2
?
After Instruction
REG1
W
C
=
=
=
1
2
1
; result is positive
Example 2:
Before Instruction
REG1
W
C
=
=
=
2
2
?
After Instruction
REG1
W
C
=
=
=
0
2
1
; result is zero
Example 3:
Before Instruction
REG1
W
C
=
=
=
1
2
?
After Instruction
REG1
W
C
DS30453A-page 52
Preliminary
=
=
=
FF
2
0
; result is negative
1997 Microchip Technology Inc.
PIC16C5X
SWAPF
Swap Nibbles in f
XORLW
Exclusive OR literal with W
Syntax:
[ label ] SWAPF f,d
Syntax:
[label]
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operands:
0 ≤ k ≤ 255
(f<3:0>) → (dest<7:4>);
(f<7:4>) → (dest<3:0>)
Operation:
Operation:
(W) .XOR. k → (W)
Status Affected: Z
Encoding:
Status Affected: None
XORLW k
1111
kkkk
kkkk
Description:
The upper and lower nibbles of register
'f' are exchanged. If 'd' is 0 the result is
placed in W register. If 'd' is 1 the result
is placed in register 'f'.
The contents of the W register are
XOR’ed with the eight bit literal 'k'. The
result is placed in the W register.
Words:
1
Cycles:
1
Words:
1
Example:
XORLW
Cycles:
1
Example
SWAPF
Encoding:
Description:
0011
10df
ffff
Before Instruction
REG1,
W
0
=
=
0xB5
After Instruction
Before Instruction
REG1
0xAF
W
0xA5
=
0x1A
After Instruction
REG1
W
=
=
0xA5
0X5A
TRIS
Load TRIS Register
XORWF
Exclusive OR W with f
Syntax:
[ label ] XORWF
Operands:
0 ≤ f ≤ 31
d ∈ [0,1]
Operation:
(W) .XOR. (f) → (dest)
Syntax:
[ label ] TRIS
Operands:
f = 5, 6 or 7
Status Affected: Z
Operation:
(W) → TRIS register f
Encoding:
f
Status Affected: None
Encoding:
0000
0000
0001
Exclusive OR the contents of the W
register with register 'f'. If 'd' is 0 the
result is stored in the W register. If 'd' is
1 the result is stored back in register 'f'.
TRIS register 'f' (f = 5, 6, or 7) is loaded
with the contents of the W register
Words:
1
Words:
1
Cycles:
1
Cycles:
1
Example
XORWF
TRIS
PORTA
Before Instruction
W
=
=
REG,1
Before Instruction
0XA5
REG
W
After Instruction
TRISA
ffff
Description:
0fff
Description:
Example
10df
f,d
0xAF
0xB5
After Instruction
0XA5
REG
W
1997 Microchip Technology Inc.
=
=
Preliminary
=
=
0x1A
0xB5
DS30453A-page 53
PIC16C5X
NOTES:
DS30453A-page 54
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
9.0
DEVELOPMENT SUPPORT
9.1
Development Tools
9.3
The PIC16/17 microcontrollers are supported with a full
range of hardware and software development tools:
• PICMASTER/PICMASTER CE Real-Time
In-Circuit Emulator
• ICEPIC Low-Cost PIC16C5X and PIC16CXXX
In-Circuit Emulator
• PRO MATE II Universal Programmer
• PICSTART Plus Entry-Level Prototype
Programmer
• PICDEM-1 Low-Cost Demonstration Board
• PICDEM-2 Low-Cost Demonstration Board
• PICDEM-3 Low-Cost Demonstration Board
• MPASM Assembler
• MPLAB SIM Software Simulator
• MPLAB-C (C Compiler)
• Fuzzy Logic Development System
(fuzzyTECH−MP)
9.2
ICEPIC: Low-Cost PIC16CXXX
In-Circuit Emulator
ICEPIC is a low-cost in-circuit emulator solution for the
Microchip PIC16C5X and PIC16CXXX families of 8-bit
OTP microcontrollers.
ICEPIC is designed to operate on PC-compatible
machines ranging from 286-AT through Pentium
based machines under Windows 3.x environment.
ICEPIC features real time, non-intrusive emulation.
9.4
PRO MATE II: Universal Programmer
The PRO MATE II Universal Programmer is a full-featured programmer capable of operating in stand-alone
mode as well as PC-hosted mode.
The PRO MATE II has programmable VDD and VPP
supplies which allows it to verify programmed memory
at VDD min and VDD max for maximum reliability. It has
an LCD display for displaying error messages, keys to
enter commands and a modular detachable socket
assembly to support various package types. In standalone mode the PRO MATE II can read, verify or program PIC16C5X, PIC16CXXX, PIC17CXX and
PIC14000 devices. It can also set configuration and
code-protect bits in this mode.
PICMASTER: High Performance
Universal In-Circuit Emulator with
MPLAB IDE
The PICMASTER Universal In-Circuit Emulator is
intended to provide the product development engineer
with a complete microcontroller design tool set for all
microcontrollers in the PIC12C5XX, PIC14C000,
PIC16C5X, PIC16CXXX and PIC17CXX families.
PICMASTER is supplied with the MPLAB Integrated
Development Environment (IDE), which allows editing,
“make” and download, and source debugging from a
single environment.
Interchangeable target probes allow the system to be
easily reconfigured for emulation of different processors. The universal architecture of the PICMASTER
allows expansion to support all new Microchip microcontrollers.
9.5
PICSTART Plus Entry Level
Development System
The PICSTART programmer is an easy-to-use, lowcost prototype programmer. It connects to the PC via
one of the COM (RS-232) ports. MPLAB Integrated
Development Environment software makes using the
programmer simple and efficient. PICSTART Plus is
not recommended for production programming.
PICSTART Plus supports all PIC12C5XX, PIC14000,
PIC16C5X, PIC16CXXX and PIC17CXX devices with
up to 40 pins. Larger pin count devices such as the
PIC16C923 and PIC16C924 may be supported with an
adapter socket.
The PICMASTER Emulator System has been
designed as a real-time emulation system with
advanced features that are generally found on more
expensive development tools. The PC compatible 386
(and higher) machine platform and Microsoft Windows
3.x environment were chosen to best make these features available to you, the end user.
A CE compliant version of PICMASTER is available for
European Union (EU) countries.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 55
PIC16C5X
9.6
PICDEM-1 Low-Cost PIC16/17
Demonstration Board
The PICDEM-1 is a simple board which demonstrates
the capabilities of several of Microchip’s microcontrollers. The microcontrollers supported are: PIC16C5X
(PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X,
PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and
PIC17C44. All necessary hardware and software is
included to run basic demo programs. The users can
program the sample microcontrollers provided with
the PICDEM-1 board, on a PRO MATE II or
PICSTART-Plus programmer, and easily test firmware. The user can also connect the PICDEM-1
board to the PICMASTER emulator and download
the firmware to the emulator for testing. Additional prototype area is available for the user to build some additional hardware and connect it to the microcontroller
socket(s). Some of the features include an RS-232
interface, a potentiometer for simulated analog input,
push-button switches and eight LEDs connected to
PORTB.
9.7
PICDEM-2 Low-Cost PIC16CXX
Demonstration Board
The PICDEM-2 is a simple demonstration board that
supports the PIC16C62, PIC16C64, PIC16C65,
PIC16C73 and PIC16C74 microcontrollers. All the
necessary hardware and software is included to
run the basic demonstration programs. The user
can program the sample microcontrollers provided
with the PICDEM-2 board, on a PRO MATE II programmer or PICSTART-Plus, and easily test firmware.
The PICMASTER emulator may also be used with the
PICDEM-2 board to test firmware. Additional prototype
area has been provided to the user for adding additional hardware and connecting it to the microcontroller
socket(s). Some of the features include a RS-232 interface, push-button switches, a potentiometer for simulated analog input, a Serial EEPROM to demonstrate
usage of the I2C bus and separate headers for connection to an LCD module and a keypad.
9.8
PICDEM-3 Low-Cost PIC16CXXX
Demonstration Board
The PICDEM-3 is a simple demonstration board that
supports the PIC16C923 and PIC16C924 in the PLCC
package. It will also support future 44-pin PLCC
microcontrollers with a LCD Module. All the necessary hardware and software is included to run the
basic demonstration programs. The user can program the sample microcontrollers provided with
the PICDEM-3 board, on a PRO MATE II programmer or PICSTART Plus with an adapter socket, and
easily test firmware. The PICMASTER emulator may
also be used with the PICDEM-3 board to test firmware. Additional prototype area has been provided to
the user for adding hardware and connecting it to the
microcontroller socket(s). Some of the features include
DS30453A-page 56
an RS-232 interface, push-button switches, a potentiometer for simulated analog input, a thermistor and
separate headers for connection to an external LCD
module and a keypad. Also provided on the PICDEM-3
board is an LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature
and day of the week. The PICDEM-3 provides an additional RS-232 interface and Windows 3.1 software for
showing the demultiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware demultiplexer for the LCD signals.
9.9
MPLAB Integrated Development
Environment Software
The MPLAB IDE Software brings an ease of software
development previously unseen in the 8-bit microcontroller market. MPLAB is a windows based application
which contains:
• A full featured editor
• Three operating modes
- editor
- emulator
- simulator
• A project manager
• Customizable tool bar and key mapping
• A status bar with project information
• Extensive on-line help
MPLAB allows you to:
• Edit your source files (either assembly or ‘C’)
• One touch assemble (or compile) and download
to PIC16/17 tools (automatically updates all
project information)
• Debug using:
- source files
- absolute listing file
• Transfer data dynamically via DDE (soon to be
replaced by OLE)
• Run up to four emulators on the same PC
The ability to use MPLAB with Microchip’s simulator
allows a consistent platform and the ability to easily
switch from the low cost simulator to the full featured
emulator with minimal retraining due to development
tools.
9.10
Assembler (MPASM)
The MPASM Universal Macro Assembler is a PChosted symbolic assembler. It supports all microcontroller series including the PIC12C5XX, PIC14000,
PIC16C5X, PIC16CXXX, and PIC17CXX families.
MPASM offers full featured Macro capabilities, conditional assembly, and several source and listing formats.
It generates various object code formats to support
Microchip's development tools as well as third party
programmers.
MPASM allows full symbolic debugging from
PICMASTER, Microchip’s Universal Emulator
System.
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
MPASM has the following features to assist in developing software for specific use applications.
• Provides translation of Assembler source code to
object code for all Microchip microcontrollers.
• Macro assembly capability.
• Produces all the files (Object, Listing, Symbol,
and special) required for symbolic debug with
Microchip’s emulator systems.
• Supports Hex (default), Decimal and Octal source
and listing formats.
MPASM provides a rich directive language to support
programming of the PIC16/17. Directives are helpful in
making the development of your assemble source code
shorter and more maintainable.
9.11
Software Simulator (MPLAB-SIM)
The MPLAB-SIM Software Simulator allows code
development in a PC host environment. It allows the
user to simulate the PIC16/17 series microcontrollers
on an instruction level. On any given instruction, the
user may examine or modify any of the data areas or
provide external stimulus to any of the pins. The input/
output radix can be set by the user and the execution
can be performed in; single step, execute until break, or
in a trace mode.
MPLAB-SIM fully supports symbolic debugging using
MPLAB-C and MPASM. The Software Simulator offers
the low cost flexibility to develop and debug code outside of the laboratory environment making it an excellent multi-project software development tool.
9.12
C Compiler (MPLAB-C)
9.14
MP-DriveWay – Application Code
Generator
MP-DriveWay is an easy-to-use Windows-based Application Code Generator. With MP-DriveWay you can
visually configure all the peripherals in a PIC16/17
device and, with a click of the mouse, generate all the
initialization and many functional code modules in C
language. The output is fully compatible with Microchip’s MPLAB-C C compiler. The code produced is
highly modular and allows easy integration of your own
code. MP-DriveWay is intelligent enough to maintain
your code through subsequent code generation.
9.15
SEEVAL Evaluation and
Programming System
The SEEVAL SEEPROM Designer’s Kit supports all
Microchip 2-wire and 3-wire Serial EEPROMs. The kit
includes everything necessary to read, write, erase or
program special features of any Microchip SEEPROM
product including Smart Serials and secure serials.
The Total Endurance Disk is included to aid in tradeoff analysis and reliability calculations. The total kit can
significantly reduce time-to-market and result in an
optimized system.
9.16
KEELOQ Evaluation and
Programming Tools
KEELOQ evaluation and programming tools support
Microchips HCS Secure Data Products. The HCS evaluation kit includes an LCD display to show changing
codes, a decoder to decode transmissions, and a programming interface to program test transmitters.
The MPLAB-C Code Development System is a
complete ‘C’ compiler and integrated development
environment for Microchip’s PIC16/17 family of microcontrollers. The compiler provides powerful integration
capabilities and ease of use not found with other
compilers.
For easier source level debugging, the compiler provides symbol information that is compatible with the
MPLAB IDE memory display.
9.13
Fuzzy Logic Development System
(fuzzyTECH-MP)
fuzzyTECH-MP fuzzy logic development tool is available in two versions - a low cost introductory version,
MP Explorer, for designers to gain a comprehensive
working knowledge of fuzzy logic system design; and a
full-featured version, fuzzyTECH-MP, edition for implementing more complex systems.
Both versions include Microchip’s fuzzyLAB demonstration board for hands-on experience with fuzzy logic
systems implementation.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 57
Emulator Products
Software Tools
DS30453A-page 58
Preliminary
Programmers
✔
KEELOQ
Evaluation Kit
PICDEM-3
PICDEM-2
PICDEM-1
SEEVAL
Designers Kit
KEELOQ
Programmer
PRO MATE II
Universal
Programmer
PICSTART
Plus Low-Cost
Universal Dev. Kit
PICSTART
Lite Ultra Low-Cost
Dev. Kit
Total Endurance
Software Model
✔
✔
✔
fuzzyTECH-MP
Explorer/Edition
Fuzzy Logic
Dev. Tool
MP-DriveWay
Applications
Code Generator
✔
MPLAB C
Compiler
✔
✔
MPLAB
Integrated
Development
Environment
ICEPIC Low-Cost
In-Circuit Emulator
PICMASTER/
PICMASTER-CE
In-Circuit Emulator
✔
✔
✔
✔
✔
✔
PIC14000
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
PIC16C5X
✔
✔
✔
✔
✔
✔
✔
✔
✔
PIC16CXXX
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
PIC16C6X PIC16C7XX PIC16C8X PIC16C9XX PIC17C4X
✔
✔
✔
✔
Available
3Q97
PIC17C75X
✔
✔
✔
24CXX
25CXX
93CXX
✔
✔
✔
HCS200
HCS300
HCS301
TABLE 9-1:
Demo Boards
PIC12C5XX
PIC16C5X
DEVELOPMENT TOOLS FROM MICROCHIP
1997 Microchip Technology Inc.
PIC16C5X
PIC16C52
10.0
ELECTRICAL CHARACTERISTICS - PIC16C52
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature.............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..............................................................................................................0 V to +7.5 V
Voltage on MCLR with respect to VSS............................................................................................................0 V to +14 V
Voltage on all other pins with respect to VSS ................................................................................–0.6 V to (VDD + 0.6 V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin........................................................................................................................................50 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output Clamp Current, IOK (VO < 0 or VO > VDD) ............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................10 mA
Max. Output Current sourced by any I/O pin...........................................................................................................10 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................10 mA
Max. Output Current sunk by a single I/O port (PORTA or B) .................................................................................10 mA
Note 1: Power Dissipation is calculated as follows: Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL)
†NOTICE: Stresses
above those listed under "Maximum Ratings" may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 59
PIC16C5X
10.1
PIC16C52
DC Characteristics: PIC16C52-04 (Commercial)
PIC16C52-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Typ(1)
Sym
Min
Supply Voltage
VDD
3.0
RAM Data Retention Voltage(2)
VDR
1.5*
Supply Current(3,4)
IDD
1.8
3.3
mA
FOSC = 4 MHz, VDD = 5.5 V
0.6
0.6
9
12
µA
µA
VDD = 3.0 V
VDD = 3.0 V
Power Down
Commercial
Industrial
Current(5)
Max
Units
Conditions
6.25
V
FOSC = DC to 4 MHz
V
Device in SLEEP Mode
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: For RC option, does not include current through Rext. The current through the resistor can be estimated by
the formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 60
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C52
10.2
DC Characteristics: PIC16C52-04 (Commercial)
PIC16C52-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 10.1.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
Hysteresis of Schmitt
Trigger inputs
Input Leakage Current(2,3)
I/O ports
VHYS
Typ(1)
Min
Max
Units
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
0.15VDD*
MCLR
–3
–3
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
RC(4) option only
XT option
For all VDD(5)
4.0 V < VDD ≤ 5.5 V(5)
VDD > 5.5 V
RC(4) option only
XT option
For VDD ≤ 5.5 V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25 V
VPIN = VDD
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT option
0.5
+1
µA
0.5
0.5
0.5
+5
+3
+3
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 2.0 mA, VDD = 4.5 V
IOL = 1.6 mA, VDD = 4.5 V,
RC option
V
V
IOH = –2.0 mA, VDD = 4.5 V
IOH = –1.0 mA, VDD = 4.5 V,
RC option
–5
T0CKI
OSC1
Pin at hi-impedance
V
IIL
–1
Conditions
VDD – 0.7
VDD – 0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C52 be
driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 61
PIC16C5X
10.3
PIC16C52
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
2
to
ck
CLKOUT
cy
cycle time
drt
device reset timer
io
I/O port
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (Hi-impedance)
L
Low
T
Time
mc
osc
os
t0
MCLR
oscillator
OSC1
T0CKI
P
R
V
Z
Period
Rise
Valid
Hi-impedance
FIGURE 10-1: LOAD CONDITIONS - PIC16C52
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 62
15 pF for OSC2 in XT mode when
external clock is used to
drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C52
10.4
Timing Diagrams and Specifications
FIGURE 10-2: EXTERNAL CLOCK TIMING - PIC16C52
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 10-1:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C52
AC Characteristics
Parameter
No.
Min
Typ(1)
Max
Units
External CLKIN Frequency(2)
DC
—
4
MHz
XT osc mode
Oscillator Frequency(2)
DC
—
4
MHz
RC osc mode
0.1
—
4
MHz
XT osc mode
250
—
—
ns
RC osc mode
250
—
—
ns
XT osc mode
Sym
FOSC
1
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 10.1.
TOSC
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
TCY
Instruction Cycle Time(3)
Conditions
250
—
—
ns
RC osc mode
250
—
10,000
ns
XT osc mode
—
4/FOSC
—
—
3
TosL, TosH Clock in (OSC1) Low or High Time
85*
—
—
ns
XT oscillator
4
TosR, TosF Clock in (OSC1) Rise or Fall Time
—
—
25*
ns
XT oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 63
PIC16C5X
PIC16C52
FIGURE 10-3: CLKOUT AND I/O TIMING - PIC16C52
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
14
19
12
18
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 10-2:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C52
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 10.1.
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
TckR
CLKOUT rise time(2)
—
5
15**
ns
13
TckF
CLKOUT fall time(2)
—
5
15**
ns
14
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
10
11
12
15
16
Sym
Characteristic
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
TioF
Port output fall time(3)
—
10
25**
ns
21
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 10-1 for loading conditions.
DS30453A-page 64
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C52
FIGURE 10-4: RESET AND DEVICE RESET TIMER TIMING - PIC16C52
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 10-3:
RESET AND DEVICE RESET TIMER - PIC16C52
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 10.1.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
30
TmcL
MCLR Pulse Width (low)
100*
—
—
ns
VDD = 5 V
32
TDRT
Device Reset Timer Period
9*
18*
30*
ms
VDD = 5 V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR Low
—
—
100*
ns
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 65
PIC16C5X
PIC16C52
FIGURE 10-5: TIMER0 CLOCK TIMINGS - PIC16C52
T0CKI
40
41
42
TABLE 10-4:
TIMER0 CLOCK REQUIREMENTS - PIC16C52
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 10.1.
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
DS30453A-page 66
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
11.0
ELECTRICAL CHARACTERISTICS - PIC16C54/55/56/57
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature.............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ............................................................................................................... 0V to +7.5V
Voltage on MCLR with respect to VSS(2) ......................................................................................................... 0V to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin......................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output Clamp Current, IOK (VO < 0 or VO > VDD) ............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA, B or C) .......................................................................40 mA
Max. Output Current sunk by a single I/O port (PORTA, B or C) ............................................................................50 mA
Note 1: Power Dissipation is calculated as follows: Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus,
a series resistor of 50 to 100 Ω should be used when applying a “low” level to the MCLR pin rather than pulling this pin directly to VSS
†NOTICE: Stresses
above those listed under “Maximum Ratings” may cause permanent damage to the device. This
is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 67
PIC16C5X
TABLE 11-1:
PIC16C54/55/56/57
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
(RC, XT & 10) AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C5X-RC
RC
VDD:
IDD:
IPD:
Freq:
3.0 V to 6.25 V
3.3 mA max. at 5. V
9 µA max. at 3.0 V, WDT dis
4 MHz max.
XT
VDD:
IDD:
IPD:
Freq:
3.0V to 6.25V
1.8 mA typ. at 5.5V
0.6 µA typ. at 3.0V WDT dis
4 MHz max.
HS
LP
VDD:
IDD:
IPD:
Freq:
N/A
VDD:
IDD:
IPD:
Freq:
2.5V to 6.25V
15 µA typ. at 3.0V
0.6 µA typ. at 3.0V, WDT dis
40 kHz max.
PIC16C5X-XT
PIC16C5X-10
N/A
N/A
3.0V to 6.25V
3.3 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
4 MHz max.
N/A
VDD:
IDD:
IPD:
Freq:
2.5V to 6.25V
15 µA typ. at 3.0V
0.6 µA typ. at 3.0V, WDT dis
40 kHz max.
N/A
VDD:
IDD:
IPD:
Freq:
4.5V to 5.5V
10 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
10 MHz max.
VDD:
IDD:
IPD:
Freq:
2.5V to 6.25V
15 µA typ. at 3.0V
0.6 µA typ. at 3.0V, WDT dis
40 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
TABLE 11-2:
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
(HS, LP & JW) AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
OSC
PIC16C5X-HS
RC
PIC16C5X-LP
N/A
XT
N/A
HS
VDD:
IDD:
IPD:
Freq:
4.5V to 5.5V
20 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
20 MHz max.
LP
VDD:
IDD:
IPD:
Freq:
2.5V to 6.25V
15 µA typ. at 3.0V
0.6 µA typ. at 3.0V, WDT dis
40 kHz max.
VDD:
IDD:
IPD:
Freq:
PIC16C5X/JW
N/A
VDD:
IDD:
IPD:
Freq:
3.0V to 6.25V
3.3 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
4 MHz max.
N/A
VDD:
IDD:
IPD:
Freq:
3.0V to 6.25V
3.3 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
4 MHz max.
N/A
VDD:
IDD:
IPD:
Freq:
4.5V to 5.5V
20 mA max. at 5.5V
9 µA max. at 3.0V, WDT dis
20 MHz max.
VDD:
IDD:
IPD:
Freq:
2.5V to 6.25V
32 µA max. at 32 kHz, 3.0V
9 µA max. at 3.0V, WDT dis
40 kHz max.
2.5V to 6.25V
32 µA max. at 32 kHz, 3.0V
9 µA max. at 3.0V, WDT dis
40 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30453A-page 68
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
11.1
DC Characteristics: PIC16C5X-RC, XT, 10, HS, LP (Commercial)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature 0°C ≤ TA ≤ +70°C
Sym
Typ(1)
Min
Max
Units
Conditions
6.25
6.25
5.5
5.5
6.25
V
V
V
V
V
FOSC = DC to 4 MHz
FOSC = DC to 4 MHz
FOSC = DC to 10 MHz
FOSC = DC to 20 MHz
FOSC = DC to 40 kHz
Supply Voltage
PIC16C5X-RC
PIC16C5X-XT
PIC16C5X-10
PIC16C5X-HS
PIC16C5X-LP
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP Mode
VDD Start Voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-On Reset
VDD Rise Rate to ensure
Power-On Reset
SVDD
V/ms
See Section 7.4 for details on
Power-On Reset
Supply Current(3)
PIC16C5X-RC(4)
PIC16C5X-XT
PIC16C5X-10
PIC16C5X-HS
3.0
3.0
4.5
4.5
2.5
0.05*
IDD
PIC16C5X-LP
Power Down Current(5)
1.8
1.8
4.8
4.8
9.0
15
3.3
3.3
10
10
20
32
mA
mA
mA
mA
mA
µA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.0V,
WDT disabled
4.0
0.6
12
9
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 69
PIC16C5X
11.2
PIC16C54/55/56/57
DC Characteristics: PIC16C5X-RCI, XTI, 10I, HSI, LPI (Industrial)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +85°C
Sym
Typ(1)
Min
Max
Units
Conditions
6.25
6.25
5.5
5.5
6.25
V
V
V
V
V
FOSC = DC to 4 MHz
FOSC = DC to 4 MHz
FOSC = DC to 10 MHz
FOSC = DC to 20 MHz
FOSC = DC to 40 kHz
Supply Voltage
PIC16C5X-RCI
PIC16C5X-XTI
PIC16C5X-10I
PIC16C5X-HSI
PIC16C5X-LPI
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-On Reset
VDD Rise Rate to ensure
Power-On Reset
SVDD
V/ms
See Section 7.4 for details on
Power-On Reset
Supply Current(3)
PIC16C5X-RCI(4)
PIC16C5X-XTI
PIC16C5X-10I
PIC16C5X-HSI
3.0
3.0
4.5
4.5
2.5
0.05*
IDD
PIC16C5X-LPI
Power Down Current(5)
1.8
1.8
4.8
4.8
9.0
15
3.3
3.3
10
10
20
40
mA
mA
mA
mA
mA
µA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.0V,
WDT disabled
4.0
0.6
14
12
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 70
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
11.3
DC Characteristics: PIC16C5X-RCE, XTE, 10E, HSE, LPE (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature –40°C ≤ TA ≤ +125°C
Sym
Typ (1)
Min
Max
Units
Conditions
6.0
6.0
5.5
5.5
6.0
V
V
V
V
V
FOSC = DC to 4 MHz
FOSC = DC to 4 MHz
FOSC = DC to 10 MHz
FOSC = DC to 16 MHz
FOSC = DC to 40 kHz
Supply Voltage
PIC16C5X-RCE
PIC16C5X-XTE
PIC16C5X-10E
PIC16C5X-HSE
PIC16C5X-LPE
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-On Reset
VDD rise rate to ensure
Power-On Reset
SVDD
V/ms
See Section 7.4 for details on
Power-On Reset
Supply Current(3)
PIC16C5X-RCE(4)
PIC16C5X-XTE
PIC16C5X-10E
PIC16C5X-HSE
3.25
3.25
4.5
4.5
2.5
0.05*
IDD
PIC16C5X-LPE
Power Down Current(5)
1.8
1.8
4.8
4.8
9.0
19
3.3
3.3
10
10
20
55
mA
mA
mA
mA
mA
µA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.25V,
WDT disabled
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 71
PIC16C5X
11.4
PIC16C54/55/56/57
DC Characteristics: PIC16C5X-RC, XT, 10, HS, LP (Commercial)
PIC16C5X-RCI, XTI, 10I, HSI, LPI (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
Hysteresis of Schmitt
Trigger inputs
Input Leakage Current(2,3)
I/O ports
VHYS
Typ(1)
Min
Max
Units
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
0.15VDD*
MCLR
–3
–3
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
PIC16C5X-RC only(4)
PIC16C5X-XT, 10, HS, LP
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
PIC16C5X-RC only(4)
PIC16C5X-XT, 10, HS, LP
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V
VPIN = VDD
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
PIC16C5X-XT, 10, HS, LP
0.5
+1
µA
0.5
0.5
0.5
+5
+3
+3
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
PIC16C5X-RC
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
PIC16C5X-RC
–5
T0CKI
OSC1
Pin at hi-impedance
V
IIL
–1
Conditions
VDD – 0.7
VDD – 0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For PIC16C5X-RC devices, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C5X be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30453A-page 72
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
11.5
DC Characteristics: PIC16C5X-RC, XT, 10, HS, LP (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
Hysteresis of Schmitt
Trigger inputs
Input Leakage Current (2,3)
I/O ports
VHYS
Typ(1)
Min
Max
Units
Vss
Vss
Vss
Vss
Vss
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
0.15VDD*
MCLR
–3
–3
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
PIC16C5X-RC only(4)
PIC16C5X-XT, 10, HS, LP
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5 V
PIC16C5X-RC only(4)
PIC16C5X-XT, 10, HS, LP
For VDD ≤ 5.5 V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V
VPIN = VDD
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
PIC16C5X-XT, 10, HS, LP
0.5
+1
µA
0.5
0.5
0.5
+5
+3
+3
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
PIC16C5X-RC
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
PIC16C5X-RC
–5
T0CKI
OSC1
Pin at hi-impedance
V
IIL
–1
Conditions
VDD – 0.7
VDD – 0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For PIC16C5X-RC devices, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C5X be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 73
PIC16C5X
11.6
PIC16C54/55/56/57
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
2
to
ck
CLKOUT
cy
cycle time
drt
device reset timer
io
I/O port
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (Hi-impedance)
L
Low
T
Time
mc
osc
os
t0
wdt
MCLR
oscillator
OSC1
T0CKI
watchdog timer
P
R
V
Z
Period
Rise
Valid
Hi-impedance
FIGURE 11-1: LOAD CONDITIONS - PIC16C54/55/56/57
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 74
15 pF for OSC2 in XT, HS or LP
modes when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
11.7
Timing Diagrams and Specifications
FIGURE 11-2: EXTERNAL CLOCK TIMING - PIC16C54/55/56/57
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 11-3:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54/55/56/57
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3
Sym
FOSC
Characteristic
Min
External CLKIN Frequency(2)
Oscillator Frequency(2)
Typ(1)
Max
Units
Conditions
DC
—
4
MHz
XT osc mode
DC
—
10
MHz
10 MHz mode
DC
—
20
MHz
HS osc mode (Com/Indust)
DC
—
16
MHz
HS osc mode (Extended)
DC
—
40
kHz
LP osc mode
DC
—
4
MHz
RC osc mode
0.1
—
4
MHz
XT osc mode
4
—
10
MHz
10 MHz mode
4
—
20
MHz
HS osc mode (Com/Indust)
4
—
16
MHz
HS osc mode (Extended)
DC
—
40
kHz
LP osc mode
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 75
PIC16C5X
TABLE 11-3:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54/55/56/57 (CON’T)
AC Characteristics
Parameter
No.
1
PIC16C54/55/56/57
Sym
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
XT osc mode
100
—
—
ns
10 MHz mode
50
—
—
ns
HS osc mode (Com/Indust)
Conditions
62.5
—
—
ns
HS osc mode (Extended)
25
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
250
—
10,000
ns
XT osc mode
100
—
250
ns
10 MHz mode
50
—
250
ns
HS osc mode (Com/Indust)
62.5
—
250
ns
HS osc mode (Extended)
25
—
—
µs
LP osc mode
—
4/FOSC
—
—
85*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 76
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
FIGURE 11-3: CLKOUT AND I/O TIMING - PIC16C54/55/56/57
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
14
19
12
18
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 11-4:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C54/55/56/57
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
12
TckR
CLKOUT rise time(2)
—
5
15**
ns
13
TckF
CLKOUT fall time(2)
—
5
15**
ns
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
10
11
14
15
Sym
Characteristic
16
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
21
TioF
Port output fall time(3)
—
10
25**
ns
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 11-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 77
PIC16C5X
PIC16C54/55/56/57
FIGURE 11-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C54/55/56/57
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 11-5:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C54/55/56/57
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and Section 11.3
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
30
TmcL
MCLR Pulse Width (low)
100*
—
—
ns
VDD = 5.0V
31
Twdt
Watchdog Timer Time-out Period
(No Prescaler)
9*
18*
30*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
9*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR Low
—
—
100*
ns
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 78
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
FIGURE 11-5: TIMER0 CLOCK TIMINGS - PIC16C54/55/56/57
T0CKI
40
41
42
TABLE 11-6:
TIMER0 CLOCK REQUIREMENTS - PIC16C54/55/56/57
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 11.1, Section 11.2 and
Section 11.3
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 79
PIC16C5X
PIC16C54/55/56/57
NOTES:
DS30453A-page 80
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
12.0
DC AND AC CHARACTERISTICS - PIC16C54/55/56/57
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some
graphs or tables the data presented are outside specified operating range (e.g., outside specified VDD range). This is
for information only and devices will operate properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of
time. “Typical” represents the mean of the distribution while “max” or “min” represents (mean + 3σ) and (mean – 3σ)
respectively, where σ is standard deviation.
FIGURE 12-1: TYPICAL RC OSCILLATOR FREQUENCY vs. TEMPERATURE
FOSC
FOSC (25°C)
Frequency normalized to +25°C
1.10
Rext ≥ 10 kΩ
Cext = 100 pF
1.08
1.06
1.04
1.02
1.00
0.98
VDD = 5.5 V
0.96
0.94
VDD = 3.5 V
0.92
0.90
0.88
0
10
20
25
30
40
50
60
70
T(°C)
TABLE 12-1:
RC OSCILLATOR FREQUENCIES
Cext
Average
Fosc @ 5 V, 25°C
Rext
20 pF
3.3 k
5k
10 k
100 k
100 pF
3.3 k
5k
10 k
100 k
300 pF
3.3 k
5.0 k
10 k
160 k
The frequencies are measured on DIP packages.
4.973 MHz
3.82 MHz
2.22 MHz
262.15 kHz
1.63 MHz
1.19 MHz
684.64 kHz
71.56 kHz
660 kHz
484.1 kHz
267.63 kHz
29.44 kHz
± 27%
± 21%
± 21%
± 31%
± 13%
± 13%
± 18%
± 25%
± 10%
± 14%
± 15%
± 19%
The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation
indicated is ±3 standard deviation from average value for VDD = 5 V.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 81
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-2: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
CEXT = 20 PF
FIGURE 12-3: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
CEXT = 100 PF
5.5
1.8
R = 3.3k
R = 3.3k
5.0
1.6
4.5
1.4
R = 5k
3.5
FOSC (MHz)
R = 5k
1.2
FOSC (MHz)
4.0
3.0
1.0
0.8
R = 10k
R = 10k
2.5
0.6
2.0
0.4
Measured on DIP Packages, T = 25°C
Measured on DIP Packages, T = 25°C
0.2
1.5
R = 100k
0.0
3.0
1.0
4.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
4.5
5.0
5.5
6.0
VDD (Volts)
R = 100k
0.5
0.0
3.0
3.5
6.0
FIGURE 12-4: TYPICAL RC OSCILLATOR
FREQUENCY vs. VDD,
CEXT = 300 PF
800
700
R = 3.3k
600
R = 5k
FOSC (kHz)
500
400
R = 10k
300
200
Measured on DIP Packages, T = 25°C
100
R = 100k
0
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VDD (Volts)
DS30453A-page 82
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-5: TYPICAL IPD vs. VDD,
WATCHDOG DISABLED
FIGURE 12-7: TYPICAL IPD vs. VDD,
WATCHDOG ENABLED
2.5
20
18
2.0
16
14
T = 25°C
T = 25°C
12
IPD (µA)
IPD (µA)
1.5
1.0
10
8
6
0.5
4
2
0.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (Volts)
FIGURE 12-6: MAXIMUM IPD vs. VDD,
WATCHDOG DISABLED
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (Volts)
FIGURE 12-8: MAXIMUM IPD vs. VDD,
WATCHDOG ENABLED
60
100
50
+125˚C
10
+85˚C
40
+70˚C
–55°C
IPD (mA)
0˚C
+85°C
30
1
IPD (µA)
–40˚C
–55˚C
+125°C
–40°C
+70°C
20
0°C
10
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0
VDD (Volts)
0
2.5
3.0
3.5
4.0 4.5 5.0
VDD (Volts)
5.5
6.0
6.5 7.0
IPD, with WDT enabled, has two components:
The leakage current which increases with higher temperature
and the operating current of the WDT logic which increases
with lower temperature. At –40°C, the latter dominates
explaining the apparently anomalous behavior.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 83
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-9: VTH (INPUT THRESHOLD VOLTAGE) OF I/O PINS vs. VDD
2.00
1.80
–40°C
Max (
VTH (Volts)
1.60
°C)
to +85
5°C)
1.40
2
Typ (+
1.20
1.00
°C)
to +85
40°C
Min (–
0.80
0.60
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.5
5.0
6.0
FIGURE 12-10: VIH, VIL OF MCLR, T0CKI AND OSC1 (IN RC MODE) vs. VDD
4.5
5°C)
4.0
3.5
VIH, VIL (Volts)
VIH
max
3.0
(–40
+8
°C to
°C
+25
typ
C)
+85°
o
t
C
40°
in (–
VIH
2.5
VIH
m
2.0
°C to +85°C)
VIL max (–40
VIH typ +25°C
1.5
1.0
5°C)
0.5
VIL min (–40°C to +8
0.0
2.5
3.0
3.5
4.0
Note: These input pins have Schmitt Trigger input buffers.
4.5
VDD (Volts)
5.0
5.5
6.0
5.5
6.0
FIGURE 12-11: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT
(IN XT, HS, AND LP MODES) vs. VDD
3.4
3.2
3.0
2.8
85°
VTH (Volts)
2.6
Max
2.4
2.2
o+
°C t
(–40
C)
)
°C
+25
(
Typ
C)
85°
o+
°C t
2.0
Min
1.8
(–40
1.6
1.4
1.2
1.0
2.5
DS30453A-page 84
3.0
3.5
4.0
4.5
VDD (Volts)
Preliminary
5.0
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-12: TYPICAL IDD vs. FREQUENCY (EXTERNAL CLOCK, 25°C)
10
IDD (mA)
1.0
0.1
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
0.01
10k
100k
1M
External Clock Frequency (Hz)
10M
100M
FIGURE 12-13: MAXIMUM IDD vs. FREQUENCY (EXTERNAL CLOCK, –40°C TO +85°C)
10
IDD (mA)
1.0
0.1
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
0.01
10k
100k
1M
10M
100M
External Clock Frequency (Hz)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 85
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-14: MAXIMUM IDD vs. FREQUENCY (EXTERNAL CLOCK –55°C TO +125°C)
10
IDD (mA)
1.0
0.1
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
0.01
10k
100k
1M
External Clock Frequency (Hz)
FIGURE 12-15: WDT TIMER TIME-OUT
PERIOD vs. VDD
10M
100M
FIGURE 12-16: TRANSCONDUCTANCE (gm)
OF HS OSCILLATOR vs. VDD
50
9000
45
8000
40
7000
35
6000
30
gm (µA/V)
WDT period (ms)
Max –40°C
Max +85°C
25
5000
Typ +25°C
4000
Max +70°C
20
3000
Typ +25°C
Min +85°C
15
2000
MIn 0°C
10
100
MIn –40°C
5
0
2
DS30453A-page 86
3
4
5
VDD (Volts)
6
7
2
Preliminary
3
4
5
VDD (Volts)
6
7
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-17: TRANSCONDUCTANCE (gm)
OF LP OSCILLATOR vs. VDD
FIGURE 12-19: TRANSCONDUCTANCE (gm)
OF XT OSCILLATOR vs. VDD
45
2500
40
Max –40°C
Max –40°C
2000
35
30
gm (µA/V)
gm (µA/V)
1500
25
Typ +25°C
20
Typ +25°C
1000
15
Min +85°C
500
10
Min +85°C
5
0
2
0
2
3
4
5
VDD (Volts)
6
3
7
4
5
6
7
VDD (Volts)
FIGURE 12-18: IOH vs. VOH, VDD = 3 V
FIGURE 12-20: IOH vs. VOH, VDD = 5 V
0
0
Min +85°C
–5
–10
–10
IOH (mA)
IOH (mA)
Min +85°C
Typ +25°C
–20
Typ +25°C
–15
Max –40°C
–30
Max –40°C
–20
–40
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
–25
0
0.5
1.0
1.5
2.0
2.5
3.0
VOH (Volts)
1997 Microchip Technology Inc.
Preliminary
VOH (Volts)
DS30453A-page 87
PIC16C5X
PIC16C54/55/56/57
FIGURE 12-21: IOL vs. VOL, VDD = 3 V
FIGURE 12-22: IOL vs. VOL, VDD = 5 V
90
45
80
Max –40°C
40
35
70
30
60
25
50
Max –40°C
IOL (mA)
IOL (mA)
Typ +25°C
Typ +25°C
20
40
Min +85°C
30
15
Min +85°C
10
20
5
10
0
0.0
0.5
TABLE 12-2:
1.0
1.5 2.0
VOL (Volts)
2.5
0
0.0
3.0
0.5
1.5
2.0
2.5
3.0
VOL (Volts)
INPUT CAPACITANCE FOR
PIC16C54/56
TABLE 12-3:
INPUT CAPACITANCE FOR
PIC16C55/57
Typical Capacitance (pF)
Typical Capacitance (pF)
Pin
18L PDIP
18L SOIC
RA port
5.0
4.3
RB port
5.0
4.3
MCLR
17.0
17.0
OSC1
4.0
3.5
OSC2/CLKOUT
4.3
3.5
T0CKI
3.2
2.8
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
DS30453A-page 88
1.0
Pin
28L PDIP
(600 mil)
28L SOIC
RA port
5.2
4.8
RB port
5.6
4.7
RC port
5.0
4.1
MCLR
17.0
17.0
OSC1
6.6
3.5
OSC2/CLKOUT
4.6
3.5
T0CKI
4.5
3.5
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
13.0
ELECTRICAL CHARACTERISTICS - PIC16CR54A
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature.............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS(2) ............................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin........................................................................................................................................50 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output Clamp Current, IOK (V0 < 0 or V0 > VDD) .............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................40 mA
Max. Output Current sunk by a single I/O port (PORTA or B) .................................................................................50 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
Note 2: Voltage spikes below Vss at the MCLR pin, inducing currents greater than 80 mA may cause latch-up. Thus,
a series resistor of 50 to 100Ω should be used when applying a low level to the MCLR pin rather than pulling
this pin directly to Vss.
†NOTICE:
Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 89
PIC16C5X
TABLE 13-1:
OSC
RC
XT
PIC16CR54A
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16CR54A-04
VDD: 2.5 V to 6.25 V
IDD: 3.6 mA max at 6.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
Freq: 4 MHz max
VDD: 2.5 V to 6.25 V
IDD: 3.6 mA max at 6.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
Freq: 4.0 MHz max
HS
N/A
PIC16CR54A-10
PIC16CR54A-20
PIC16LCR54A-04
N/A
N/A
N/A
N/A
N/A
N/A
VDD: 4.5 V to 5.5 V
IDD: 10 mA max at 5.5 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
Freq: 10 MHz max
VDD: 4.5 V to 5.5 V
IDD: 10 mA max at 5.5 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
Freq: 20 MHz max
LP
N/A
N/A
N/A
N/A
VDD: 2.0 V to 6.25 V
IDD: 20 µA max at 32 kHz,
2.0 V
IPD: 6.0 µA max at 2.5 V,
WDT dis
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30453A-page 90
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
13.1
DC Characteristics: PIC16CR54A-04, 10, 20 (Commercial)
PIC16CR54A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1)
Max
Units
6.25
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
Supply Current(3)
RC(4) and XT options
2.5
4.5
0.05*
IDD
HS option
Power-Down Current(5)
Commercial
Power-Down Current(5)
Industrial
2.0
0.8
90
4.8
9.0
3.6
1.8
350
10
20
mA
mA
µA
mA
mA
FOSC = 4.0 MHz, VDD = 6.0V
FOSC = 4.0 MHz, VDD = 3.0V
FOSC = 200 kHz, VDD = 2.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
1.0
2.0
3.0
5.0
6.0
8.0*
15
25
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
45
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
IPD
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 91
PIC16C5X
13.2
PIC16CR54A
DC Characteristics: PIC16CR54A-04E, 10E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1)
Max
Units
6.0
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
3.25
4.5
Supply Current(3)
RC(4) and XT options
HS option
IDD
Power-Down Current(5)
IPD
0.05*
1.8
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 16 MHz, VDD = 5.5V
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 92
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
13.3
DC Characteristics: PIC16LCR54A-04 (Commercial)
PIC16LCR54A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
2.0
Typ(1)
Max
6.25
Units
Conditions
V
Supply Voltage
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
Supply Current(3)
Power-Down Current(5)
Commercial
Power-Down Current(5)
Industrial
0.05*
IDD
10
20
70
µA
µA
FOSC = 32 kHz, VDD = 2.0V
FOSC = 32 kHz, VDD = 6.0V
1.0
2.0
3.0
5.0
6.0
8.0*
15
25
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
1.0
2.0
3.0
3.0
5.0
8.0
10*
20*
18
45
µA
µA
µA
µA
µA
VDD = 2.5V, WDT disabled
VDD = 4.0V, WDT disabled
VDD = 4.0V, WDT enabled
VDD = 6.0V, WDT disabled
VDD = 6.0V, WDT enabled
IPD
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 93
PIC16C5X
13.4
PIC16CR54A
DC Characteristics: PIC16CR54A-04, 10, 20, PIC16LCR54A-04 (Commercial)
PIC16CR54A-04I, 10I, 20I, PIC16LCR54A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 13.1 and Section 13.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
VSS
VSS
VSS
VSS
VSS
Input Leakage Current(3)
I/O ports
VHYS
Max
0.2
0.15
0.15
0.15
0.15
2.0
0.6 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.85 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Typ(1)
Min
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
0.15VDD*
Units
V
V
V
V
V
V
V
V
V
V
V
–1.0
0.5
0.5
0.5
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage(3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
VDD = 3.0V to 5.5V(5)
Full VDD range(5)
RC option only(4)
XT, HS and LP options
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.5
0.5
V
V
IOL = 10 mA, VDD = 6.0V
IOL = 1.9 mA, VDD = 6.0V,
RC option only
V
V
IOH = –4.0 mA, VDD = 6.0V
IOH = –0.8 mA, VDD = 6.0V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
MCLR
Conditions
VDD –0.5
VDD –0.5
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30453A-page 94
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
13.5
DC Characteristics: PIC16CR54A-04E, 10E, 20E (Extended)
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C
Operating Voltage VDD range is described in Section 13.2.
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Input Leakage Current(3)
I/O ports
VHYS
Min
Typ(1)
Max
Units
Vss
Vss
Vss
Vss
Vss
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
V
0.15VDD*
MCLR
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage (3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
RC option only(4)
XT, HS and LP options
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
0.5
+1.0
µA
0.5
0.5
0.5
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
–1.0
Conditions
VDD –0.7
VDD –0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 95
PIC16C5X
13.6
PIC16CR54A
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
T
Time
Lowercase subscripts (pp) and their meanings:
pp
2
to
mc
MCLR
ck
CLKOUT
osc
oscillator
cy
cycle time
os
OSC1
drt
device reset timer
t0
T0CKI
io
I/O port
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
Fall
P
Period
H
High
R
Rise
I
Invalid (Hi-impedance)
V
Valid
L
Low
Z
Hi-impedance
FIGURE 13-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 96
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
13.7
Timing Diagrams and Specifications
FIGURE 13-2: EXTERNAL CLOCK TIMING - PIC16CR54A
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 13-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 13.1, Section 13.2 and Section 13.3.
Sym
FOSC
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
4.0
MHz
HS osc mode (04)
DC
—
10
MHz
HS osc mode (10)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
DC
—
4.0
MHz
RC osc mode
0.1
—
4.0
MHz
XT osc mode
4.0
—
4.0
MHz
HS osc mode (04)
4.0
—
10
MHz
HS osc mode (10)
4.0
—
20
MHz
HS osc mode (20)
5.0
—
200
kHz
LP osc mode
Min
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 97
PIC16C5X
TABLE 13-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR54A (CON’T)
AC Characteristics
Parameter
No.
1
PIC16CR54A
Sym
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 13.1, Section 13.2 and Section 13.3.
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
XT osc mode
250
—
—
ns
HS osc mode (04)
100
—
—
ns
HS osc mode (10)
Conditions
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
250
—
10,000
ns
XT osc mode
250
—
250
ns
HS osc mode (04)
100
—
250
ns
HS osc mode (10)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
—
4/FOSC
—
—
50*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 98
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
FIGURE 13-3: CLKOUT AND I/O TIMING - PIC16CR54A
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
19
12
18
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 13-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR54A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 13.1, Section 13.2 and
Section 13.3.
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
12
TckR
CLKOUT rise time(2)
—
5.0
15**
ns
13
TckF
CLKOUT fall time(2)
—
5.0
15**
ns
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
10
11
14
15
Sym
Characteristic
16
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
21
TioF
Port output fall time(3)
—
10
25**
ns
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 13-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 99
PIC16C5X
PIC16CR54A
FIGURE 13-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR54A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 13-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR54A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 13.1, Section 13.2 and Section 13.3.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
30
TmcL
MCLR Pulse Width (low)
1.0*
—
—
µs
VDD = 5.0V
31
Twdt
Watchdog Timer Time-out Period
(No Prescaler)
7.0*
18*
40*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
7.0*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR Low
—
—
1.0*
µs
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 100
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR54A
FIGURE 13-5: TIMER0 CLOCK TIMINGS - PIC16CR54A
T0CKI
40
41
42
TABLE 13-5:
TIMER0 CLOCK REQUIREMENTS - PIC16CR54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 13.1, Section 13.2 and
Section 13.3.
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 101
PIC16C5X
PIC16CR54A
NOTES:
DS30453A-page 102
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
14.0
ELECTRICAL CHARACTERISTICS - PIC16C54A
Absolute Maximum Ratings†
Ambient temperature under bias............................................................................................................ –55°C to +125°C
Storage temperature ............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS................................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total power dissipation(1) .....................................................................................................................................800 mW
Max. current out of VSS pin....................................................................................................................................150 mA
Max. current into VDD pin ......................................................................................................................................100 mA
Max. current into an input pin (T0CKI only)......................................................................................................................±500 µA
Input clamp current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) ..............................................................................................................±20 mA
Max. output current sunk by any I/O pin..................................................................................................................25 mA
Max. output current sourced by any I/O pin ............................................................................................................20 mA
Max. output current sourced by a single I/O port (PORTA or B) .............................................................................50 mA
Max. output current sunk by a single I/O port (PORTA or B)...................................................................................50 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 103
PIC16C5X
TABLE 14-1:
OSC
RC
XT
HS
LP
PIC16C54A
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C54A-04
VDD: 3.0V to 6.25V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4 MHz max.
VDD: 3.0V to 6.25V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4 MHz max.
N/A
VDD: 3.0V to 6.25V
IDD: 14 µA typ. at
32kHz, 3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 200 kHz max.
PIC16C54A-10
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 8.0 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 10 MHz max.
Do not use in
LP mode
PIC16C54A-20
PIC16LC54A-04
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 16 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 20 MHz max.
VDD: 3.0V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
Do not use in
LP mode
Do not use in
HS mode
VDD: 2.5V to 6.25V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not
tested. It is recommended that the user select the device type from information in unshaded
sections.
OSC
RC
XT
HS
LP
PIC16C54A/JW
VDD: 3.0V to 6.25V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 8 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 10 MHz max.
VDD: 2.5V to 6.25V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
PIC16LV54A-02
VDD: 2.0V to 3.8V
IDD: 0.5 mA typ. at
3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 2.0 MHz max.
VDD: 2.0V to 3.8V
IDD: 0.5 mA typ. at
3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 2.0 MHz max.
Do not use in
HS mode
VDD: 2.0V to 3.8V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
The shaded sections indicate oscillator selections
which should work by design, but are not tested. It
is recommended that the user select the device
type from information in unshaded sections.
DS30453A-page 104
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
14.1
DC Characteristics: PIC16C54A-04, 10, 20 (Commercial)
PIC16C54A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
4.5
6.25
5.5
Conditions
Supply Voltage
XT, RC and LP options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
IDD
0.05*
V/ms See Section 7.4 for details on
Power-on Reset
1.8
2.4
4.5
14
17
2.4
8.0
16
29
37
mA
mA
mA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
4.0
0.25
5.0
0.3
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
LP option, Commercial
LP option, Industrial
Power Down Current(5)
Commercial
Industrial
V
V
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 105
PIC16C5X
14.2
PIC16C54A
DC Characteristics: PIC16C54A-04E, 10E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1) Max Units
3.5
4.5
5.5
5.5
Conditions
Supply Voltage
XT and RC options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
IDD
Power Down Current(5)
XT and RC options
IPD
HS option
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
1.8
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
5.0
0.8
4.0
0.25
22
18
22
18
µA
µA
µA
µA
VDD = 3.5V, WDT enabled
VDD = 3.5V, WDT disabled
VDD = 3.5V, WDT enabled
VDD = 3.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 106
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
14.3
DC Characteristics: PIC16LC54A-04 (Commercial)
PIC16LC54A-04I (Industrial)
PIC16LC54A-04E (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
2.5
6.25
6.25
Conditions
Supply Voltage
XT and RC options
LP options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
LP option, Commercial
LP option, Industrial
LP option, Extended
IDD
Power Down Current(5)
Commercial
IPD
Industrial
Extended
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
0.5
11
11
11
25
27
35
37
mA
µA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 2.5V WDT disabled
FOSC = 32 kHz, VDD = 2.5V WDT disabled
FOSC = 32 kHz, VDD = 2.5V WDT disabled
2.5
0.25
2.5
0.25
2.5
0.25
12
4.0
14
5.0
15
7.0
µA
µA
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 107
PIC16C5X
14.4
PIC16C54A
DC Characteristics: PIC16LV54A-02 (Commercial)
PIC16LV54A-02 (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–20°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Supply Voltage
XT, RC and LP options
Min
Typ(1) Max Units
2.0
3.8
Conditions
VDD
(2)
V
RAM Data Retention Voltage
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
LP option, Commercial
LP option, Industrial
IDD
Power Down Current(5)(6)
Commercial
IPD
Industrial
0.05*
V/ms See Section 7.4 for details on
Power-on Reset
0.5
11
14
27
35
mA
µA
µA
FOSC = 2.0 MHz, VDD = 3.0V
FOSC = 32 kHz, VDD = 2.5V, WDT disabled
FOSC = 32 kHz, VDD = 2.5V, WDT disabled
2.5
0.25
3.5
0.3
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
6: The oscillator start-up time can be as much as 8 seconds for XT and LP oscillator selection, if the SLEEP
mode is entered or during initial power-up.
DS30453A-page 108
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
14.5
DC Characteristics: PIC16C54A-04, 10, 20, PIC16LC54A-04, PIC16LV54A-02 (Commercial)
PIC16C54A-04I, 10I, 20I, PIC16LC54A-04I, PIC16LV54A-02I (Industrial)
PIC16C54A-04E, 10E, 20E (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and
Section 14.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
VHYS
Input Leakage Current(3)
I/O ports
IIL
Min
Max
Units
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.2 VDD+1V
2.0
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
0.15VDD*
-1.0
MCLR
Typ(1)
-3.0
-3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
Pin at hi-impedance
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
RC option only(4)
XT, HS and LP options
V
0.5
-5.0
T0CKI
OSC1
Conditions
0.5
0.5
0.5
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS +0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = -5.4 mA, VDD = 4.5V
IOH = -1.0 mA, VDD = 4.5V,
RC option only
VDD-0.7
VDD-0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 109
PIC16C5X
14.6
PIC16C54A
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
2
to
ck
CLKOUT
cy
cycle time
drt
device reset timer
io
I/O port
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (Hi-impedance)
L
Low
T
Time
mc
osc
os
t0
wdt
MCLR
oscillator
OSC1
T0CKI
watchdog timer
P
R
V
Z
Period
Rise
Valid
Hi-impedance
FIGURE 14-1: LOAD CONDITIONS - PIC16C54A
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 110
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
14.7
Timing Diagrams and Specifications
FIGURE 14-2: EXTERNAL CLOCK TIMING - PIC16C54A
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 14-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Sym
FOSC
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
Min
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
2.0
MHz
XT osc mode (PIC16LV54A)
DC
—
4.0
MHz
HS osc mode (04)
DC
—
10
MHz
HS osc mode (10)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
DC
—
4.0
MHz
RC osc mode
DC
—
2.0
MHz
RC osc mode (PIC16LV54A)
0.1
—
4.0
MHz
XT osc mode
0.1
—
2.0
MHz
XT osc mode (PIC16LV54A)
4
—
4.0
MHz
HS osc mode (04)
4
—
10
MHz
HS osc mode (10)
4
—
20
MHz
HS osc mode (20)
5
—
200
kHz
LP osc mode
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 111
PIC16C5X
TABLE 14-2:
PIC16C54A
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C54A (CON’T)
AC Characteristics
Parameter
No.
Sym
1
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
Conditions
XT osc mode
500
—
—
ns
XT osc mode (PIC16LV54A)
250
—
—
ns
HS osc mode (04)
100
—
—
ns
HS osc mode (10)
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
500
—
—
ns
RC osc mode (PIC16LV54A)
250
—
10,000
ns
XT osc mode
500
—
—
ns
XT osc mode (PIC16LV54A)
250
—
250
ns
HS osc mode (04)
100
—
250
ns
HS osc mode (10)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
—
4/FOSC
—
—
85*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 112
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
FIGURE 14-3: CLKOUT AND I/O TIMING - PIC16C54A
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
14
19
12
18
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 14-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C54A
AC Characteristics
Parameter
No.
Sym
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and
Section 14.3.
Characteristic
Min
Typ(1)
Max
Units
10
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
11
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
TckR
CLKOUT rise time(2)
—
5.0
15**
ns
TckF
CLKOUT fall time(2)
—
5.0
15**
ns
14
TckL2ioV
CLKOUT↓ to Port out valid(2)
15
TioV2ckH
Port in valid before CLKOUT↑(2)
16
TckH2ioI
17
12
13
—
—
40**
ns
0.25 TCY+30*
—
—
ns
Port in hold after CLKOUT↑(2)
0*
—
—
ns
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
TioF
Port output fall time(3)
—
10
25**
ns
21
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 14-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 113
PIC16C5X
PIC16C54A
FIGURE 14-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C54A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 14-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C54A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and Section 14.3.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
Conditions
30
TmcL
MCLR Pulse Width (low)
100*
1µs
—
—
—
—
ns
VDD = 5.0V
VDD = 5.0V (PIC16LV54A only)
31
Twdt
Watchdog Timer Time-out
Period (No Prescaler)
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR
Low
—
—
—
—
100*
1µs
ns
(PIC16LV54A only)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 114
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A
FIGURE 14-5: TIMER0 CLOCK TIMINGS - PIC16C54A
T0CKI
40
41
42
TABLE 14-5:
TIMER0 CLOCK REQUIREMENTS - PIC16C54A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV54A-02I)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 14.1, Section 14.2 and
Section 14.3.
Parameter
Sym Characteristic
No.
Min
40
Tt0H T0CKI High Pulse Width - No Prescaler
41
Tt0L
- With Prescaler
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
0.5 TCY + 20*
Typ(1) Max Units Conditions
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 115
PIC16C5X
PIC16C54A
NOTES:
DS30453A-page 116
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
15.0
ELECTRICAL CHARACTERISTICS - PIC16CR57B
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature.............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS................................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin......................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ...................................................................................................................±20 mA
Output Clamp Current, IOK (VO < 0 or VO > VDD) ............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA, B or C) .......................................................................50 mA
Max. Output Current sunk by a single I/O port (PORTA, B or C) ............................................................................50 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†NOTICE:
Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 117
PIC16C5X
TABLE 15-1:
OSC
RC
XT
PIC16CR57B
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16CR57B-04
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 4.0 MHz max
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 4.0 MHz max
HS
N/A
PIC16CR57B-10
PIC16CR57B-20
PIC16LCR57B-04
N/A
N/A
N/A
N/A
N/A
N/A
VDD: 4.5V to 5.5V
IDD: 10 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 10 MHz max
VDD: 4.5V to 5.5V
IDD: 20 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 20 MHz max
LP
N/A
N/A
N/A
N/A
VDD: 2.5V to 6.25V
IDD: 32 µA max at 32 kHz,
2.5V
IPD: 4.0 µA max at 2.5V,
WDT dis
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30453A-page 118
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
15.1
DC Characteristics: PIC16CR57B-04, 10, 20 (Commercial)
PIC16CR57B-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1)
Max
Units
6.25
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
3.0
4.5
Supply Current(3)
RC(4) and XT options
HS option
IDD
Power-Down Current(5)
Commercial
IPD
Industrial
0.05*
1.9
2.5
4.7
2.5
8.0
17
mA
mA
mA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
4.0
0.25
4.0
0.25
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 119
PIC16C5X
15.2
PIC16CR57B
DC Characteristics: PIC16CR57B-04E, 10E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1)
Max
Units
6.0
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
3.25
4.5
Supply Current(3)
RC(4) and XT options
HS option
IDD
Power-Down Current(5)
IPD
0.05*
1.9
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 120
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
15.3
DC Characteristics: PIC16LCR57B-04 (Commercial)
PIC16LCR57B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Typ(1)
Sym
Min
Supply Voltage
VDD
2.5
V
LP option
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
Supply Current(3)
Commercial
6.25
0.05*
Units
Conditions
IDD
Industrial
Power-Down Current(5)
Commercial
Max
12
28
µA
15
37
µA
3.5
0.2
3.5
0.2
12
4.0
14
5.0
µA
µA
µA
µA
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
IPD
Industrial
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 121
PIC16C5X
15.4
PIC16CR57B
DC Characteristics: PIC16CR57B-04, 10, 20, PIC16LCR57B-04 (Commercial)
PIC16CR57B-04I, 10I, 20I, PIC16LCR57B-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 15.1 and Section 15.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
VSS
VSS
VSS
VSS
VSS
Input Leakage Current(3)
I/O ports
VHYS
Max
0.2
0.15
0.15
0.15
0.3
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Typ(1)
Min
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
0.15VDD*
Units
V
V
V
V
V
V
V
V
V
V
V
V
–1.0
0.5
0.5
0.5
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage(3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
RC option only(4)
XT, HS and LP options
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
MCLR
Conditions
VDD –0.7
VDD –0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30453A-page 122
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
15.5
DC Characteristics: PIC16CR57B-04E, 10E, 20E (Extended)
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C
Operating Voltage VDD range is described in Section 15.2.
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
Input Leakage Current(3)
I/O ports
Typ(1)
VSS
VSS
VSS
VSS
VSS
VHYS
Max
0.2
0.15
0.15
0.15
0.3
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Min
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
0.15VDD*
Units
V
V
V
V
V
V
V
V
V
V
V
V
–1.0
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage(3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
RC option only(4)
XT, HS and LP options
0.5
0.5
0.5
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25 V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
MCLR
Conditions
VDD –0.7
VDD –0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 123
PIC16C5X
15.6
PIC16CR57B
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
T
Time
Lowercase subscripts (pp) and their meanings:
pp
2
to
mc
MCLR
ck
CLKOUT
osc
oscillator
cy
cycle time
os
OSC1
drt
device reset timer
t0
T0CKI
io
I/O port
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
Fall
P
Period
H
High
R
Rise
I
Invalid (Hi-impedance)
V
Valid
L
Low
Z
Hi-impedance
FIGURE 15-1: LOAD CONDITIONS
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 124
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
15.7
Timing Diagrams and Specifications
FIGURE 15-2: EXTERNAL CLOCK TIMING - PIC16CR57B
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 15-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57B
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Sym
FOSC
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
Min
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
4.0
MHz
HS osc mode (04)
DC
—
10
MHz
HS osc mode (10)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
DC
—
4.0
MHz
RC osc mode
0.1
—
4.0
MHz
XT osc mode
4.0
—
4.0
MHz
HS osc mode (04)
4.0
—
10
MHz
HS osc mode (10)
4.0
—
20
MHz
HS osc mode (20)
5.0
—
200
kHz
LP osc mode
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 125
PIC16C5X
TABLE 15-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR57B (CON’T)
AC Characteristics
Parameter
No.
1
PIC16CR57B
Sym
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
XT osc mode
250
—
—
ns
HS osc mode (04)
100
—
—
ns
HS osc mode (10)
Conditions
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
250
—
10,000
ns
XT osc mode
250
—
250
ns
HS osc mode (04)
100
—
250
ns
HS osc mode (10)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
—
4/FOSC
—
—
85*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 126
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
FIGURE 15-3: CLKOUT AND I/O TIMING - PIC16CR57B
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
19
12
18
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 15-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR57B
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and
Section 15.3.
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
12
TckR
CLKOUT rise time(2)
—
5.0
15**
ns
13
TckF
CLKOUT fall time(2)
—
5.0
15**
ns
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
10
11
14
15
Sym
Characteristic
16
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
21
TioF
Port output fall time(3)
—
10
25**
ns
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 15-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 127
PIC16C5X
PIC16CR57B
FIGURE 15-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR57B
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 15-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR57B
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and Section 15.3.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
30
TmcL
MCLR Pulse Width (low)
1.0*
—
—
µs
VDD = 5.0V
31
Twdt
Watchdog Timer Time-out Period
(No Prescaler)
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR Low
—
—
1.0*
µs
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 128
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR57B
FIGURE 15-5: TIMER0 CLOCK TIMINGS - PIC16CR57B
T0CKI
40
41
42
TABLE 15-5:
TIMER0 CLOCK REQUIREMENTS - PIC16CR57B
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 15.1, Section 15.2 and
Section 15.3.
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 129
PIC16C5X
PIC16CR57B
NOTES:
DS30453A-page 130
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
16.0
ELECTRICAL CHARACTERISTICS - PIC16C58A
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS................................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin......................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output Clamp Current, IOK (VO < 0 or VO > VDD) ............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................50 mA
Max. Output Current sunk by a single I/O port (PORTA or B) .................................................................................50 mA
Note 1: Power Dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 131
PIC16C5X
TABLE 16-1:
OSC
RC
XT
HS
LP
PIC16C58A
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C58A-04
VDD: 3.0V to 6.25V
IDD: 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
N/A
VDD: 3.0V to 6.25V
IDD: 15 µA typ. at
32kHz, 3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 200 kHz max.
PIC16C58A-10
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 8.0 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 10 MHz max.
Do not use in
LP mode
PIC16C58A-20
PIC16LC58A-04
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 1.8 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 17 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 20 MHz max.
VDD: 3.0V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD: 0.5 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
Do not use in
LP mode
Do not use in
HS mode
VDD: 2.5V to 6.25V
IDD: 28 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which should work by design, but are not
tested. It is recommended that the user select the device type from information in unshaded
sections.
OSC
RC
XT
HS
LP
PIC16C58A/JW
VDD: 3.0V to 6.25V
IDD: 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 6.25V
IDD 2.5 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 17 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 20 MHz max.
VDD: 2.5V to 6.25V
IDD: 28 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
PIC16LV58A-02
VDD: 2.0V to 3.8V
IDD: 0.5 mA typ. at
3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 2.0 MHz max.
VDD: 2.0V to 3.8V
IDD: 0.5 mA typ. at
3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 2.0 MHz max.
Do not use in
HS mode
VDD: 2.0V to 3.8V
IDD: 27 µA max. at
32kHz, 2.5V
WDT dis
IPD: 4.0 µA max. at
2.5V WDT dis
Freq: 200 kHz max.
The shaded sections indicate oscillator selections
which should work by design, but are not tested. It
is recommended that the user select the device
type from information in unshaded sections.
DS30453A-page 132
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
16.1
DC Characteristics: PIC16C58A-04, 10, 20 (Commercial)
PIC16C58A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
4.5
6.25
5.5
Conditions
Supply Voltage
XT, RC and LP options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
IDD
0.05*
V/ms See Section 7.4 for details on
Power-on Reset
1.9
2.5
4.7
15
18
2.5
8.0
17
31
39
mA
mA
mA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
4.0
0.25
5.0
0.3
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
LP option, Commercial
LP option, Industrial
Power Down Current(5)
Commercial
Industrial
V
V
IPD
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 133
PIC16C5X
16.2
PIC16C58A
DC Characteristics: PIC16C58A-04E, 10E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1) Max Units
3.5
4.5
5.5
5.5
Conditions
Supply Voltage
XT and RC options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
IDD
Power Down Current(5)
XT and RC options
IPD
HS option
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
1.9
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
5.0
0.8
4.0
0.25
22
18
22
18
µA
µA
µA
µA
VDD = 3.5V, WDT enabled
VDD = 3.5V, WDT disabled
VDD = 3.5V, WDT enabled
VDD = 3.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design
guidance only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 134
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
16.3
DC Characteristics: PIC16LC58A-04 (Commercial)
PIC16LC58A-04I (Industrial)
PIC16LC58A-04 (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
2.5
6.25
6.25
Conditions
Supply Voltage
XT and RC options
LP options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
LP option, Commercial
LP option, Industrial
LP option, Extended
IDD
Power Down Current(5)
Commercial
IPD
Industrial
Extended
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
0.5
12
12
12
2.5
27
35
37
mA
µA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 2.5V WDT disabled
FOSC = 32 kHz, VDD = 2.5V WDT disabled
FOSC = 32 kHz, VDD = 2.5V WDT disabled
2.5
0.25
2.5
0.25
2.5
0.25
12
4.0
14
5.0
15
7.0
µA
µA
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 135
PIC16C5X
16.4
PIC16C58A
DC Characteristics: PIC16LV58A-02 (Commercial)
PIC16LV58A-02 (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–20°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Supply Voltage
XT, RC and LP options
Min
Typ(1) Max Units
2.0
3.8
Conditions
VDD
(2)
V
RAM Data Retention Voltage
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See section on Power-On Reset for details
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
LP option, Commercial
LP option, Industrial
IDD
Power Down Current(5)(6)
Commercial
IPD
Industrial
0.05*
V/ms See section on Power-On Reset for details
0.5
11
14
1.8
27
35
mA
µA
µA
FOSC = 2.0 MHz, VDD = 3.0V
FOSC = 32 kHz, VDD = 2.5V, WDT disabled
FOSC = 32 kHz, VDD = 2.5V, WDT disabled
2.5
0.25
2.5
0.25
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
6: The oscillator start-up time can be as much as 8 seconds for XT and LP oscillator selection, if the SLEEP
mode is entered or during initial power-up.
DS30453A-page 136
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
16.5
DC Characteristics: PIC16C58A-04, 10, 20, PIC16LC58A-04, PIC16LV58A-02 (Commercial)
PIC16C58A-04I, 10I, 20I, PIC16LC58A-04I, PIC16LV58A-02I (Industrial)
PIC16C58A-04E, 10E, 20E (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and
Section 16.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
VHYS
Input Leakage Current(3)
I/O ports
IIL
Min
Max
Units
VSS
VSS
VSS
VSS
VSS
0.2 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
0.2 VDD+1V
2.0
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
0.15VDD*
-1.0
MCLR
Typ(1)
-3.0
-3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
Pin at hi-impedance
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
RC option only(4)
XT, HS and LP options
V
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS +0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
0.5
+1.0
µA
0.5
0.5
0.5
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = -5.4 mA, VDD = 4.5V
IOH = -1.0 mA, VDD = 4.5V,
RC option only
-5.0
T0CKI
OSC1
Conditions
VDD-0.7
VDD-0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 137
PIC16C5X
16.6
PIC16C58A
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
2
to
ck
CLKOUT
cy
cycle time
drt
device reset timer
io
I/O port
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (Hi-impedance)
L
Low
T
Time
mc
osc
os
t0
wdt
MCLR
oscillator
OSC1
T0CKI
watchdog timer
P
R
V
Z
Period
Rise
Valid
Hi-impedance
FIGURE 16-1: LOAD CONDITIONS - PIC16C58A
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 138
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
16.7
Timing Diagrams and Specifications
FIGURE 16-2: EXTERNAL CLOCK TIMING - PIC16C58A
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 16-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C58A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Sym
FOSC
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
Min
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
2.0
MHz
XT osc mode (PIC16LV58A)
DC
—
4.0
MHz
HS osc mode (04)
DC
—
10
MHz
HS osc mode (10)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
DC
—
4.0
MHz
RC osc mode
DC
—
2.0
MHz
RC osc mode (PIC16LV58A)
0.1
—
4.0
MHz
XT osc mode
0.1
—
2.0
MHz
XT osc mode (PIC16LV58A)
4.0
—
4.0
MHz
HS osc mode (04)
4.0
—
10
MHz
HS osc mode (10)
4.0
—
20
MHz
HS osc mode (20)
5.0
—
200
kHz
LP osc mode
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 139
PIC16C5X
TABLE 16-2:
PIC16C58A
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C58A (CON’T)
AC Characteristics
Parameter
No.
Sym
1
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
Conditions
XT osc mode
500
—
—
ns
XT osc mode (PIC16LV58A)
250
—
—
ns
HS osc mode (04)
100
—
—
ns
HS osc mode (10)
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
500
—
—
ns
RC osc mode (PIC16LV58A)
250
—
10,000
ns
XT osc mode
500
—
—
ns
XT osc mode (PIC16LV58A)
250
—
250
ns
HS osc mode (04)
100
—
250
ns
HS osc mode (10)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
—
4/FOSC
—
—
50*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 140
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
FIGURE 16-3: CLKOUT AND I/O TIMING - PIC16C58A
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
14
19
12
18
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 16-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C58A
AC Characteristics
Parameter
No.
Sym
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and
Section 16.3.
Characteristic
Min
Typ(1)
Max
Units
10
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
11
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
TckR
CLKOUT rise time(2)
—
5
15**
ns
TckF
CLKOUT fall time(2)
—
5
15**
ns
14
TckL2ioV
CLKOUT↓ to Port out valid(2)
15
TioV2ckH
Port in valid before CLKOUT↑(2)
16
TckH2ioI
17
12
13
—
—
40**
ns
0.25 TCY+30*
—
—
ns
Port in hold after CLKOUT↑(2)
0*
—
—
ns
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
TioF
Port output fall time(3)
—
10
25**
ns
21
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25˚C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 16-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 141
PIC16C5X
PIC16C58A
FIGURE 16-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C58A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 16-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C58A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and Section 16.3.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
Conditions
30
TmcL
MCLR Pulse Width (low)
100*
1µs
—
—
—
—
ns
VDD = 5.0V
VDD = 5.0V (PIC16LV58A only)
31
Twdt
Watchdog Timer Time-out
Period (No Prescaler)
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR
Low
—
—
—
—
100*
1µs
ns
(PIC16LV58A only)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 142
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C58A
FIGURE 16-5: TIMER0 CLOCK TIMINGS - PIC16C58A
T0CKI
40
41
42
TABLE 16-5:
TIMER0 CLOCK REQUIREMENTS - PIC16C58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–20°C ≤ TA ≤ +85°C (industrial - PIC16LV58A)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 16.1, Section 16.2 and
Section 16.3.
Parameter
Sym Characteristic
No.
Min
40
Tt0H T0CKI High Pulse Width - No Prescaler
41
Tt0L
- With Prescaler
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
0.5 TCY + 20*
Typ(1) Max Units Conditions
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 143
PIC16C5X
PIC16C58A
NOTES:
DS30453A-page 144
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
17.0
ELECTRICAL CHARACTERISTICS - PIC16CR58A
Absolute Maximum Ratings†
Ambient Temperature under bias ........................................................................................................... –55°C to +125°C
Storage Temperature.............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS................................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total Power Dissipation(1).....................................................................................................................................800 mW
Max. Current out of VSS pin...................................................................................................................................150 mA
Max. Current into VDD pin......................................................................................................................................100 mA
Max. Current into an input pin (T0CKI only).....................................................................................................................±500 µA
Input Clamp Current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output Clamp Current, IOK (VO < 0 or VO> VDD)..............................................................................................................±20 mA
Max. Output Current sunk by any I/O pin ................................................................................................................25 mA
Max. Output Current sourced by any I/O pin...........................................................................................................20 mA
Max. Output Current sourced by a single I/O port (PORTA or B)............................................................................50 mA
Max. Output Current sunk by a single I/O port (PORTA or B) .................................................................................50 mA
Note 1: Power Dissipation is calculated as follows: PDIS = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†NOTICE:
Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 145
PIC16C5X
TABLE 17-1:
OSC
RC
XT
PIC16CR58A
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16CR58A-04
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 4.0 MHz max
VDD: 3.0V to 6.25V
IDD: 2.5 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 4.0 MHz max
HS
N/A
PIC16CR58A-10
PIC16CR58A-20
PIC16LCR58A-04
N/A
N/A
N/A
N/A
N/A
N/A
VDD: 4.5V to 5.5V
IDD: 8.0 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 10 MHz max
VDD: 4.5V to 5.5V
IDD: 17 mA max at 5.5V
IPD: 4.0 µA max at 3.0V,
WDT dis
Freq: 20 MHz max
LP
N/A
N/A
N/A
N/A
VDD: 2.5V to 6.25V
IDD: 28 µA max at 32 kHz,
2.5V
IPD: 4.0 µA max at 2.5V,
WDT dis
Freq: 200 kHz max
The shaded sections indicate oscillator selections which should work by design, but are not tested. It is recommended
that the user select the device type from information in unshaded sections.
DS30453A-page 146
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
17.1
DC Characteristics: PIC16CR58A-04, 10, 20 (Commercial)
PIC16CR58A-04I, 10I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1)
Max
Units
6.25
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
3.0
4.5
Supply Current(3)
RC(4) and XT options
HS option
IDD
Power-Down Current(5)
Commercial
IPD
Industrial
0.05*
1.9
2.5
4.7
2.5
8.0
17
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
4.0
0.25
4.0
0.25
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 147
PIC16C5X
17.2
PIC16CR58A
DC Characteristics: PIC16CR58A-04E, 10E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1)
Max
Units
6.0
5.5
V
V
Conditions
Supply Voltage
RC and XT options
HS options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
3.25
4.5
Supply Current(3)
RC(4) and XT options
HS option
IDD
Power-Down Current(5)
IPD
0.05*
1.9
4.8
9.0
3.3
10
20
mA
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 10 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
5.0
0.8
22
18
µA
µA
VDD = 3.25V, WDT enabled
VDD = 3.25V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 148
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
17.3
DC Characteristics: PIC16LCR58A-04 (Commercial)
PIC16LCR58A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Typ(1)
Sym
Min
Supply Voltage
VDD
2.5
V
LP option
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD Start Voltage to ensure
Power-on Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD Rise Rate to ensure
Power-on Reset
SVDD
V/ms
See Section 7.4 for details on
Power-on Reset
Supply Current(3)
Commercial
6.25
0.05*
Units
Conditions
IDD
Industrial
Power-Down Current(5)
Commercial
Max
12
28
µA
15
37
µA
3.5
0.2
3.5
0.2
12
4.0
14
5.0
µA
µA
µA
µA
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
FOSC = 32 kHz, VDD = 2.5V,
WDT disabled
IPD
Industrial
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 149
PIC16C5X
17.4
PIC16CR58A
DC Characteristics: PIC16CR58A-04, 10, 20, PIC16LCR58A-04 (Commercial)
PIC16CR58A-04I, 10I, 20I, PIC16LCR58A-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
Operating Voltage VDD range is described in Section 17.1 and Section 17.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
VSS
VSS
VSS
VSS
VSS
Input Leakage Current(3)
I/O ports
VHYS
Max
0.2
0.15
0.15
0.15
0.3
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Typ(1)
Min
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
0.15VDD*
Units
V
V
V
V
V
V
V
V
V
V
V
V
–1.0
0.5
0.5
0.5
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage(3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
RC option only(4)
XT, HS and LP options
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
MCLR
Conditions
VDD –0.7
VDD –0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30453A-page 150
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
17.5
DC Characteristics: PIC16CR58A-04E, 10E, 20E (Extended)
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.2.
Sym
Input Low Voltage
I/O ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
Input Leakage Current(3)
I/O ports
Typ(1)
VSS
VSS
VSS
VSS
VSS
VHYS
Max
0.2
0.15
0.15
0.15
0.3
0.45 VDD
2.0
0.36 VDD
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Min
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
0.15VDD*
Units
V
V
V
V
V
V
V
V
V
V
V
V
–1.0
–3.0
–3.0
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage(3)
I/O ports
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
For all VDD(5)
4.0V < VDD ≤ 5.5V(5)
VDD > 5.5V
RC option only(4)
XT, HS and LP options
0.5
0.5
0.5
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS + 0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = –5.4 mA, VDD = 4.5V
IOH = –1.0 mA, VDD = 4.5V,
RC option only
–5.0
T0CKI
OSC1
Pin at hi-impedance
V
IIL
MCLR
Conditions
VDD –0.7
VDD –0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X
be driven with external clock in RC mode.
5: The user may use the better of the two specifications.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 151
PIC16C5X
17.6
PIC16CR58A
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
T
Time
Lowercase subscripts (pp) and their meanings:
pp
2
to
mc
MCLR
ck
CLKOUT
osc
oscillator
cy
cycle time
os
OSC1
drt
device reset timer
t0
T0CKI
io
I/O port
wdt
watchdog timer
Uppercase letters and their meanings:
S
F
Fall
P
Period
H
High
R
Rise
I
Invalid (Hi-impedance)
V
Valid
L
Low
Z
Hi-impedance
FIGURE 17-1: LOAD CONDITIONS - PIC16CR58A
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
DS30453A-page 152
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
17.7
Timing Diagrams and Specifications
FIGURE 17-2: EXTERNAL CLOCK TIMING - PIC16CR58A
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 17-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR58A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.1, Section 17.2 and Section 17.3.
Sym
FOSC
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
4.0
MHz
HS osc mode (04)
DC
—
10
MHz
HS osc mode (10)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
DC
—
4.0
MHz
RC osc mode
0.1
—
4.0
MHz
XT osc mode
4.0
—
4.0
MHz
HS osc mode (04)
4.0
—
10
MHz
HS osc mode (10)
4.0
—
20
MHz
HS osc mode (20)
5.0
—
200
kHz
LP osc mode
Min
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 153
PIC16C5X
TABLE 17-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16CR58A (CON’T)
AC Characteristics
Parameter
No.
1
PIC16CR58A
Sym
TOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.1, Section 17.2 and Section 17.3.
Characteristic
External CLKIN Period(2)
Oscillator Period(2)
2
3
4
TCY
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
250
—
—
ns
XT osc mode
250
—
—
ns
HS osc mode (04)
100
—
—
ns
HS osc mode (10)
Conditions
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
250
—
10,000
ns
XT osc mode
250
—
250
ns
HS osc mode (04)
100
—
250
ns
HS osc mode (10)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
—
4/FOSC
—
—
85*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating
conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation
and/or higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 154
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
FIGURE 17-3: CLKOUT AND I/O TIMING - PIC16CR58A
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
19
12
18
16
14
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 17-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16CR58A
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.1, Section 17.2 and
Section 17.3.
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
12
TckR
CLKOUT rise time(2)
—
5.0
15**
ns
13
TckF
CLKOUT fall time(2)
—
5.0
15**
ns
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
10
11
14
15
Sym
Characteristic
16
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
21
TioF
Port output fall time(3)
—
10
25**
ns
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 17-1 for loading conditions.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 155
PIC16C5X
PIC16CR58A
FIGURE 17-4: RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER TIMING - PIC16CR58A
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 17-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16CR58A
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.1, Section 17.2 and Section 17.3.
Parameter
No.
Sym
Characteristic
Min
Typ(1)
Max
Units
30
TmcL
MCLR Pulse Width (low)
1.0*
—
—
µs
VDD = 5.0V
31
Twdt
Watchdog Timer Time-out Period
(No Prescaler)
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
32
TDRT
Device Reset Timer Period
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
34
TioZ
I/O Hi-impedance from MCLR Low
—
—
1.0*
µs
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
DS30453A-page 156
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16CR58A
FIGURE 17-5: TIMER0 CLOCK TIMINGS - PIC16CR58A
T0CKI
40
41
42
TABLE 17-5:
TIMER0 CLOCK REQUIREMENTS - PIC16CR58A
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 17.1, Section 17.2 and
Section 17.3.
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 157
PIC16C5X
PIC16CR58A
NOTES:
DS30453A-page 158
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
18.0
DC AND AC CHARACTERISTICS - PIC16C54A/CR57B/C58A/CR58A
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some
graphs or tables the data presented are outside specified operating range (e.g., outside specified VDD range). This is
for information only and devices will operate properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of
time. “Typical” represents the mean of the distribution while “max” or “min” represents (mean + 3σ) and (mean – 3σ)
respectively, where σ is standard deviation.
FIGURE 18-1: TYPICAL RC OSCILLATOR FREQUENCY vs. TEMPERATURE
FOSC
FOSC (25°C)
Frequency normalized to +25°C
1.10
Rext ≥ 10 kΩ
Cext = 100 pF
1.08
1.06
1.04
1.02
1.00
0.98
VDD = 5.5 V
0.96
0.94
VDD = 3.5 V
0.92
0.90
0.88
0
10
20
25
30
40
50
60
70
T(°C)
TABLE 18-1:
RC OSCILLATOR FREQUENCIES
Cext
Average
Fosc @ 5 V, 25°C
Rext
20 pF
3.3 k
5k
10 k
100 k
100 pF
3.3 k
5k
10 k
100 k
300 pF
3.3 k
5.0 k
10 k
160 k
The frequencies are measured on DIP packages.
4.973 MHz
3.82 MHz
2.22 MHz
262.15 kHz
1.63 MHz
1.19 MHz
684.64 kHz
71.56 kHz
660 kHz
484.1 kHz
267.63 kHz
29.44 kHz
± 27%
± 21%
± 21%
± 31%
± 13%
± 13%
± 18%
± 25%
± 10%
± 14%
± 15%
± 19%
The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation
indicated is ±3 standard deviation from average value for VDD = 5 V.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 159
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-2: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 20 PF
6.00
R=3.3K
5.00
R=5.0K
Fosc(MHz)
4.00
3.00
R=10K
2.00
Cext=20pF, T=25C
1.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
5.5
6
VDD(Volts)
FIGURE 18-3: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 100 PF
1.80
R=3.3K
1.60
1.40
R=5.0K
Fosc(MHz)
1.20
1.00
0.80
R=10K
0.60
Cext=100pF, T=25C
0.40
0.20
R=100K
0.00
2.5
3
3.5
4
4.5
5
VDD(Volts)
DS30453A-page 160
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-4: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 300 PF
700.00
R=3.3K
600.00
500.00
Fosc(KHz)
R=5.0K
400.00
300.00
R=10K
200.00
Cext=300pF, T=25C
100.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 18-5: TYPICAL IPD vs. VDD, WATCHDOG DISABLED (25°C)
2.5
2
Ipd(µA)
Ipd(nA)
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 161
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-6: TYPICAL IPD vs. VDD, WATCHDOG ENABLED (25°C)
25.00
20.00
Ipd(uA)
15.00
10.00
5.00
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 18-7: VTH (INPUT THRESHOLD VOLTAGE) OF I/O PINS vs. VDD
2.00
1.80
–40°C
Max (
VTH (Volts)
1.60
°C)
to +85
5°C)
1.40
2
Typ (+
1.20
1.00
to
40°C
Min (–
0.80
0.60
2.5
DS30453A-page 162
3.0
3.5
4.0
4.5
VDD (Volts)
Preliminary
+85°C
)
5.0
5.5
6.0
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-8: VIH, VIL OF MCLR, T0CKI AND OSC1 (IN RC MODE) vs. VDD
4.5
4.0
3.5
VIH, VIL (Volts)
VIH
max
3.0
to
40°C
+85°
C)
(–
°C
+25
typ
5°C)
to +8
C
°
40
in (–
VIH
2.5
VIH
m
2.0
°C to +85°C)
VIL max (–40
VIH typ +25°C
1.5
1.0
5°C)
0.5
VIL min (–40°C to +8
0.0
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
6.0
5.5
6.0
Note: These input pins have Schmitt Trigger input buffers.
FIGURE 18-9: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT
(IN XT, HS, AND LP MODES) vs. VDD
3.4
3.2
3.0
2.8
85°
VTH (Volts)
2.6
Max
2.4
2.2
o+
°C t
(–40
C)
)
°C
+25
(
Typ
C)
85°
o+
°C t
2.0
Min
1.8
(–40
1.6
1.4
1.2
1.0
2.5
3.0
1997 Microchip Technology Inc.
3.5
4.0
4.5
VDD (Volts)
Preliminary
5.0
DS30453A-page 163
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-10: TYPICAL IDD vs. FREQUENCY (WDT( DIS, RC@MODE
@
p
) 20 PF, 25°C)
10000
Idd(uA)
1000
100
5.0V
4.0V
3.0V
6.0V
5.5V
4.5V
3.5V
2.5V
10
100000
1000000
10000000
Freq(Hz)
@ 20 PF, –40°C TO +85°C)
FIGURE 18-11: MAXIMUM IDD vs. FREQUENCY (WDT( DIS, RC@ MODE
p )
10000
Idd(uA)
1000
100
10
100000
6.0V
5.5V
5.0V
4.5V
4.0V
`3.5V
3.0V
2.5V
1000000
10000000
Freq(Hz)
DS30453A-page 164
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-12: TYPICAL IDD vs. FREQUENCY (WDT( DIS, RC
@ MODE
p
)@ 100 PF, 25°C)
10000
Idd(uA)
1000
100
10
10000
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
100000
1000000
10000000
Freq(Hz)
FIGURE 18-13: MAXIMUM IDD vs. FREQUENCY (WDT DIS, RC MODE @ 100 PF, –40°C TO +85°C)
10000
Idd(uA)
1000
100
10
10000
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
100000
1000000
10000000
Freq(Hz)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 165
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-14: TYPICAL IDD vs. FREQUENCY (WDT( DIS, RC
@ MODE
p
)@ 300 PF, 25°C)
10000
Idd(uA)
1000
100
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
Freq(Hz)
FIGURE 18-15: MAXIMUM IDD vs. FREQUENCY (WDT DIS, RC MODE @ 300 PF, –40°C TO +85°C)
10000
Idd(uA)
1000
100
6.0V
5.5V
5.0V
4.5V
4.0V
3.5V
3.0V
2.5V
10
10000
100000
1000000
Freq(Hz)
DS30453A-page 166
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-16: WDT TIMER TIME-OUT
PERIOD vs. VDD
TABLE 18-2:
Typical Capacitance (pF)
50
Pin
45
40
35
WDT period (ms)
INPUT CAPACITANCE FOR
PIC16C54A/C58A
30
Max +85°C
18L PDIP
18L SOIC
RA port
5.0
4.3
RB port
5.0
4.3
MCLR
17.0
17.0
OSC1
4.0
3.5
OSC2/CLKOUT
4.3
3.5
T0CKI
3.2
2.8
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
25
Max +70°C
20
Typ +25°C
15
MIn 0°C
10
MIn –40°C
5
2
3
4
5
VDD (Volts)
1997 Microchip Technology Inc.
6
7
Preliminary
DS30453A-page 167
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-17: TRANSCONDUCTANCE (gm)
OF HS OSCILLATOR vs. VDD
FIGURE 18-18: TRANSCONDUCTANCE (gm)
OF LP OSCILLATOR vs. VDD
9000
45
8000
40
Max –40°C
7000
35
6000
30
5000
gm (µA/V)
gm (µA/V)
Max –40°C
Typ +25°C
4000
3000
25
Typ +25°C
20
15
Min +85°C
2000
10
Min +85°C
100
5
0
2
3
4
5
VDD (Volts)
6
0
7
2
3
4
5
VDD (Volts)
6
7
FIGURE 18-19: TRANSCONDUCTANCE (gm)
OF XT OSCILLATOR vs. VDD
2500
Max –40°C
2000
gm (µA/V)
1500
Typ +25°C
1000
Min +85°C
500
0
2
3
4
5
6
7
VDD (Volts)
DS30453A-page 168
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
FIGURE 18-20: IOH vs. VOH, VDD = 3 V
FIGURE 18-22: IOL vs. VOL, VDD = 3 V
0
45
Max –40°C
40
–5
35
Min +85°C
IOL (mA)
IOH (mA)
30
–10
Typ +25°C
–15
Max –40°C
25
Typ +25°C
20
15
Min +85°C
–20
10
5
–25
0
0.5
1.0
1.5
2.0
2.5
3.0
0
0.0
VOH (Volts)
0.5
1.0
1.5
2.0
2.5
3.0
VOL (Volts)
FIGURE 18-21: IOH vs. VOH, VDD = 5 V
FIGURE 18-23: IOL vs. VOL, VDD = 5 V
90
0
80
Max –40°C
Min +85°C
70
–10
Typ +25°C
–20
IOL (mA)
IOH (mA)
60
Typ +25°C
50
40
Min +85°C
30
–30
Max –40°C
20
–40
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
10
VOH (Volts)
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
VOL (Volts)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 169
PIC16C5X
PIC16C54A/CR57B/C58A/CR58A
NOTES:
DS30453A-page 170
Preliminary
1997 Microchip Technology Inc.
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
19.0
PIC16C5X
ELECTRICAL CHARACTERISTICS PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
Absolute Maximum Ratings†
Ambient temperature under bias............................................................................................................ –55°C to +125°C
Storage temperature ............................................................................................................................. –65°C to +150°C
Voltage on VDD with respect to VSS ..................................................................................................................0 to +7.5V
Voltage on MCLR with respect to VSS................................................................................................................0 to +14V
Voltage on all other pins with respect to VSS ................................................................................. –0.6V to (VDD + 0.6V)
Total power dissipation(1) .....................................................................................................................................800 mW
Max. current out of VSS pin....................................................................................................................................150 mA
Max. current into VDD pin ......................................................................................................................................100 mA
Max. current into an input pin (T0CKI only)......................................................................................................................±500 µA
Input clamp current, IIK (VI < 0 or VI > VDD) ....................................................................................................................±20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) ..............................................................................................................±20 mA
Max. output current sunk by any I/O pin..................................................................................................................25 mA
Max. output current sourced by any I/O pin ............................................................................................................20 mA
Max. output current sourced by a single I/O port A ................................................................................................50 mA
Max. output current sourced by a single I/O port B ................................................................................................50 mA
Max. output current sunk by a single I/O port A ......................................................................................................50 mA
Max. output current sunk by a single I/O port B .....................................................................................................50 mA
Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOL x IOL)
†
NOTICE: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 171
PIC16C5X
TABLE 19-1:
OSC
RC
XT
HS
LP
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS
AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES)
PIC16C5X-04
VDD: 3.0V to 5.5V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4 MHz max.
VDD: 3.0V to 5.5V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4 MHz max.
N/A
VDD: 3.0V to 5.5V
IDD: 14 µA typ. at
32kHz, 3.0V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 200 kHz max.
PIC16C5X-20
VDD: 3.0V to 5.5V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 5.5V
IDD: 1.7 mA typ. at
5.5V
IPD: 0.25 µA typ. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 16 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 20 MHz max.
Do not use in
LP mode
PIC16C5X/JW
VDD: 3.0V to 5.5V
IDD: 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 3.0V to 5.5V
IDD 2.4 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 4.0 MHz max.
VDD: 4.5V to 5.5V
IDD: 16 mA max. at
5.5V
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 20 MHz max.
VDD: 3.0V to 5.5V
IDD: 32 µA max. at
32kHz, 3.0V
WDT dis
IPD: 4.0 µA max. at
3.0V WDT dis
Freq: 200 kHz max.
The shaded sections indicate oscillator selections which should work by
design, but are not tested. It is recommended that the user select the
device type from information in unshaded sections.
DS30453A-page 172
Preliminary
1997 Microchip Technology Inc.
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
19.1
PIC16C5X
DC Characteristics: PIC16C5X-04, 20 (Commercial)
PIC16CR5X-04, 20 (Commercial)
PIC16C5X-04I, 20I (Industrial)
PIC16CR5X-04I, 20I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
4.5
5.5
5.5
Conditions
Supply Voltage
XT, RC and LP options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
LP option, Commercial
LP option, Industrial
IDD
Power Down Current(5)
Commercial
IPD
Industrial
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
1.8
4.5
14
17
2.4
16
32
40
mA
mA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
4.0
0.25
4.0
0.25
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
VDD = 3.0V, WDT enabled
VDD = 3.0V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 173
PIC16C5X
19.2
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
DC Characteristics: PIC16C5X-04E, 20E (Extended)
PIC16CR5X-04E, 20E (Extended)
DC Characteristics
Power Supply Pins
Characteristic
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
–40°C ≤ TA ≤ +125°C (extended)
Sym
Min
Typ(1) Max Units
3.0
4.5
5.5
5.5
Conditions
Supply Voltage
XT and RC options
HS option
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
HS option
IDD
Power Down Current(5)
IPD
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
1.8
9.0
3.3
20
mA
mA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 20 MHz, VDD = 5.5V
0.3
4.5
18
22
µA
µA
VDD = 3.5V, WDT disabled
VDD = 3.5V, WDT enabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
DS30453A-page 174
Preliminary
1997 Microchip Technology Inc.
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
19.3
PIC16C5X
DC Characteristics: PIC16LCR5X-04 (Commercial)
PIC16LCR5X-04I (Industrial)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
DC Characteristics
Power Supply Pins
Characteristic
Sym
Min
Typ(1) Max Units
3.0
2.5
5.5
5.5
Conditions
Supply Voltage
XT and RC options
LP options
VDD
RAM Data Retention Voltage(2)
VDR
1.5*
V
Device in SLEEP mode
VDD start voltage to ensure
Power-On Reset
VPOR
VSS
V
See Section 7.4 for details on
Power-on Reset
VDD rise rate to ensure
Power-On Reset
SVDD
Supply Current(3)
XT and RC(4) options
LP option, Commercial
LP option, Industrial
IDD
Power Down Current(5)
Commercial
IPD
Industrial
0.05*
V
V
V/ms See Section 7.4 for details on
Power-on Reset
0.5
11
14
2.4
27
35
mA
µA
µA
FOSC = 4.0 MHz, VDD = 5.5V
FOSC = 32 kHz, VDD = 2.5V WDT disabled
FOSC = 32 kHz, VDD = 2.5V WDT disabled
2.5
0.25
2.5
0.25
12
4.0
14
5.0
µA
µA
µA
µA
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
VDD = 2.5V, WDT enabled
VDD = 2.5V, WDT disabled
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus
loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on
the current consumption.
a) The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to
Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified.
b) For standby current measurements, the conditions are the same, except that
the device is in SLEEP mode.
4: Does not include current through Rext. The current through the resistor can be estimated by the
formula: IR = VDD/2Rext (mA) with Rext in kΩ.
5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 175
PIC16C5X
19.4
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
DC Characteristics: PIC16C5X-04, 20, PIC16LCR5X-04 (Commercial)
PIC16CR5X-04, 20, PIC16CR5X-04I, 20I (Commercial)
PIC16C5X-04I, 20I, PIC16LC5X-04I (Industrial)
PIC16C5X-04E, 20E (Extended)
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and
Section 19.3.
DC Characteristics
All Pins Except
Power Supply Pins
Characteristic
Sym
Input Low Voltage
I/O Ports
I/O Ports
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
VIL
Input High Voltage
I/O ports
VIH
MCLR (Schmitt Trigger)
T0CKI (Schmitt Trigger)
OSC1 (Schmitt Trigger)
OSC1
Hysteresis of Schmitt
Trigger inputs
Input Leakage Current(3)
I/O ports
VHYS
Typ(1)
Min
Max
Units
VSS
VSS
VSS
VSS
VSS
0.8 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.15 VDD
0.3 VDD
V
V
V
V
V
Pin at hi-impedance 4.5V , VDD ≤ 5.5V
Pin at hi-impedance 2.5V , VDD ≤ 4.5V
0.25 VDD+0.8V
2.0
0.85 VDD
0.85 VDD
0.85 VDD
0.7 VDD
VDD
VDD
VDD
VDD
VDD
VDD
V
V
V
V
V
V
For all VDD(5)
4.5V < VDD ≤ 5.5V(5)
0.15VDD*
MCLR
0.5
-5.0
-3.0
-3.0
T0CKI
OSC1
Output Low Voltage
I/O ports
OSC2/CLKOUT
VOL
Output High Voltage
I/O ports(3)
OSC2/CLKOUT
VOH
RC option only(4)
XT, HS and LP options
RC option only(4)
XT, HS and LP options
V
IIL
-1.0
Conditions
0.5
0.5
0.5
For VDD ≤ 5.5V
VSS ≤ VPIN ≤ VDD,
Pin at hi-impedance
VPIN = VSS +0.25V(2)
VPIN = VDD(2)
VSS ≤ VPIN ≤ VDD
VSS ≤ VPIN ≤ VDD,
XT, HS and LP options
+1.0
µA
+5.0
+3.0
+3.0
µA
µA
µA
µA
0.6
0.6
V
V
IOL = 8.7 mA, VDD = 4.5V
IOL = 1.6 mA, VDD = 4.5V,
RC option only
V
V
IOH = -5.4 mA, VDD = 4.5V
IOH = -1.0 mA, VDD = 4.5V,
RC option only
VDD-0.7
VDD-0.7
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance
only and is not tested.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltage.
3: Negative current is defined as coming out of the pin.
4: For the RC option, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16C5X be
driven with external clock in RC mode.
5: The user may use the better of the two specifications.
DS30453A-page 176
Preliminary
1997 Microchip Technology Inc.
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
19.5
PIC16C5X
Timing Parameter Symbology and Load Conditions
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS
2. TppS
T
F
Frequency
Lowercase subscripts (pp) and their meanings:
pp
2
to
ck
CLKOUT
cy
cycle time
drt
device reset timer
io
I/O port
Uppercase letters and their meanings:
S
F
Fall
H
High
I
Invalid (Hi-impedance)
L
Low
T
Time
mc
osc
os
t0
wdt
MCLR
oscillator
OSC1
T0CKI
watchdog timer
P
R
V
Z
Period
Rise
Valid
Hi-impedance
FIGURE 19-1: LOAD CONDITIONS - PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B, PIC16CR5X
Pin
CL = 50 pF for all pins except OSC2
CL
VSS
1997 Microchip Technology Inc.
15 pF for OSC2 in XT, HS or LP
options when external clock
is used to drive OSC1
Preliminary
DS30453A-page 177
PIC16C5X
19.6
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
Timing Diagrams and Specifications
FIGURE 19-2: EXTERNAL CLOCK TIMING - PIC16C5X, PIC16CR5X
Q4
Q1
Q3
Q2
Q4
Q1
OSC1
1
3
3
4
4
2
CLKOUT
TABLE 19-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C5X, PIC16CR5X
AC Characteristics
Parameter
No.
Sym
FOSC
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and Section 19.3.
Characteristic
External CLKIN Frequency(2)
Oscillator Frequency(2)
1
TOSC
External CLKIN Period(2)
Oscillator Period(2)
Typ(1)
Max
Units
DC
—
4.0
MHz
XT osc mode
DC
—
4.0
MHz
HS osc mode (04)
DC
—
20
MHz
HS osc mode (20)
DC
—
200
kHz
LP osc mode
Min
Conditions
DC
—
4.0
MHz
RC osc mode
0.455
—
4.0
MHz
XT osc mode
4
—
4.0
MHz
HS osc mode (04)
4
—
20
MHz
HS osc mode (20)
5
—
200
kHz
LP osc mode
250
—
—
ns
XT osc mode
250
—
—
ns
HS osc mode (04)
50
—
—
ns
HS osc mode (20)
5.0
—
—
µs
LP osc mode
250
—
—
ns
RC osc mode
250
—
2,200
ns
XT osc mode
250
—
250
ns
HS osc mode (04)
50
—
250
ns
HS osc mode (20)
5.0
—
200
µs
LP osc mode
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
DS30453A-page 178
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
TABLE 19-2:
EXTERNAL CLOCK TIMING REQUIREMENTS - PIC16C5X, PIC16CR5X (CON’T)
AC Characteristics
Parameter
No.
2
3
4
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and Section 19.3.
Sym
TCY
Characteristic
Instruction Cycle Time(3)
TosL, TosH Clock in (OSC1) Low or High Time
TosR, TosF Clock in (OSC1) Rise or Fall Time
Min
Typ(1)
Max
Units
—
4/FOSC
—
—
50*
—
—
ns
XT oscillator
20*
—
—
ns
HS oscillator
2.0*
—
—
µs
LP oscillator
—
—
25*
ns
XT oscillator
—
—
25*
ns
HS oscillator
—
—
50*
ns
LP oscillator
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption.
When an external clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
3: Instruction cycle period (TCY) equals four times the input oscillator time base period.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 179
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 19-3: CLKOUT AND I/O TIMING - PIC16C5X, PIC16CR5X
Q1
Q4
Q2
Q3
OSC1
10
11
CLKOUT
13
14
19
12
18
16
I/O Pin
(input)
15
17
I/O Pin
(output)
New Value
Old Value
20, 21
Note: All tests must be done with specified capacitive loads (see data sheet) 50 pF on I/O pins and CLKOUT.
TABLE 19-3:
CLKOUT AND I/O TIMING REQUIREMENTS - PIC16C5X, PIC16CR5X
AC Characteristics
Parameter
No.
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and
Section 19.3.
Min
Typ(1)
Max
Units
TosH2ckL
OSC1↑ to CLKOUT↓(2)
—
15
30**
ns
TosH2ckH
OSC1↑ to CLKOUT↑(2)
—
15
30**
ns
12
TckR
CLKOUT rise time(2)
—
5.0
15**
ns
13
TckF
CLKOUT fall time(2)
—
5.0
15**
ns
TckL2ioV
CLKOUT↓ to Port out valid(2)
—
—
40**
ns
TioV2ckH
Port in valid before CLKOUT↑(2)
0.25 TCY+30*
—
—
ns
16
TckH2ioI
Port in hold after CLKOUT↑(2)
0*
—
—
ns
17
TosH2ioV
OSC1↑ (Q1 cycle) to Port out valid(3)
—
—
100*
ns
18
TosH2ioI
OSC1↑ (Q2 cycle) to Port input invalid
(I/O in hold time)
TBD
—
—
ns
19
TioV2osH
Port input valid to OSC1↑
(I/O in setup time)
TBD
—
—
ns
20
TioR
Port output rise time(3)
—
10
25**
ns
21
TioF
Port output fall time(3)
—
10
25**
ns
10
11
14
15
Sym
Characteristic
* These parameters are characterized but not tested.
** These parameters are design targets and are not tested. No characterization data available at this time.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
2: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
3: See Figure 19-1 for loading conditions.
DS30453A-page 180
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 19-4: RESET, WATCHDOG TIMER, AND
DEVICE RESET TIMER TIMING - PIC16C5X, PIC16CR5X
VDD
MCLR
30
Internal
POR
32
32
32
DRT
Time-out
Internal
RESET
Watchdog
Timer
RESET
31
34
34
I/O pin
(Note 1)
Note 1: I/O pins must be taken out of hi-impedance mode by enabling the output drivers in software.
TABLE 19-4:
RESET, WATCHDOG TIMER, AND DEVICE RESET TIMER - PIC16C5X, PIC16CR5X
AC Characteristics Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and Section 19.3.
Parameter
No.
Sym
Characteristic
30
TmcL
MCLR Pulse Width (low)
31
Twdt
32
34
Min
Typ(1)
Max
Units
1000*
—
—
ns
VDD = 5.0V
Watchdog Timer Time-out Period
(No Prescaler)
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
TDRT
Device Reset Timer Period
9.0*
18*
30*
ms
VDD = 5.0V (Commercial)
TioZ
I/O Hi-impedance from MCLR Low
100*
300*
1000*
ns
Conditions
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design
guidance only and are not tested.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 181
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 19-5: TIMER0 CLOCK TIMINGS - PIC16C5X, PIC16CR5X
T0CKI
40
41
42
TABLE 19-5:
TIMER0 CLOCK REQUIREMENTS - PIC16C5X, PIC16CR5X
AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
0°C ≤ TA ≤ +70°C (commercial)
–40°C ≤ TA ≤ +85°C (industrial)
–40°C ≤ TA ≤ +125°C (extended)
Operating Voltage VDD range is described in Section 19.1, Section 19.2 and
Section 19.3.
Parameter
Sym Characteristic
No.
40
Min
Tt0H T0CKI High Pulse Width - No Prescaler
- With Prescaler
41
Tt0L
T0CKI Low Pulse Width - No Prescaler
- With Prescaler
42
Tt0P T0CKI Period
Typ(1) Max Units Conditions
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
0.5 TCY + 20*
—
—
ns
10*
—
—
ns
20 or TCY + 40*
N
—
—
ns
Whichever is greater.
N = Prescale Value
(1, 2, 4,..., 256)
* These parameters are characterized but not tested.
Note 1: Data in the Typical (“Typ”) column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
DS30453A-page 182
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
20.0
DC AND AC CHARACTERISTICS PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some
graphs or tables the data presented are outside specified operating range (e.g., outside specified VDD range). This is
for information only and devices will operate properly only within the specified range.
The data presented in this section is a statistical summary of data collected on units from different lots over a period of
time. “Typical” represents the mean of the distribution while “max” or “min” represents (mean + 3σ) and (mean – 3σ)
respectively, where σ is standard deviation.
FIGURE 20-1: TYPICAL RC OSCILLATOR FREQUENCY vs. TEMPERATURE
FOSC
FOSC (25°C)
Frequency normalized to +25°C
1.10
Rext ≥ 10 kΩ
Cext = 100 pF
1.08
1.06
1.04
1.02
1.00
0.98
VDD = 5.5 V
0.96
0.94
VDD = 3.5 V
0.92
0.90
0.88
0
10
20
25
30
40
50
60
70
T(°C)
TABLE 20-1:
RC OSCILLATOR FREQUENCIES
Cext
Average
Fosc @ 5 V, 25°C
Rext
20 pF
3.3 k
5k
10 k
100 k
100 pF
3.3 k
5k
10 k
100 k
300 pF
3.3 k
5.0 k
10 k
160 k
The frequencies are measured on DIP packages.
4.973 MHz
3.82 MHz
2.22 MHz
262.15 kHz
1.63 MHz
1.19 MHz
684.64 kHz
71.56 kHz
660 kHz
484.1 kHz
267.63 kHz
29.44 kHz
± 27%
± 21%
± 21%
± 31%
± 13%
± 13%
± 18%
± 25%
± 10%
± 14%
± 15%
± 19%
The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation
indicated is ±3 standard deviation from average value for VDD = 5 V.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 183
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-2: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 20 PF
6.00
R=3.3K
5.00
R=5.0K
Fosc(MHz)
4.00
3.00
R=10K
2.00
Cext=20pF, T=25C
1.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
5.5
6
VDD(Volts)
FIGURE 20-3: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 100 PF
1.80
R=3.3K
1.60
1.40
R=5.0K
Fosc(MHz)
1.20
1.00
0.80
R=10K
0.60
Cext=100pF, T=25C
0.40
0.20
R=100K
0.00
2.5
3
3.5
4
4.5
5
VDD(Volts)
DS30453A-page 184
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-4: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 300 PF
700.00
R=3.3K
600.00
500.00
Fosc(KHz)
R=5.0K
400.00
300.00
R=10K
200.00
Cext=300pF, T=25C
100.00
R=100K
0.00
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
FIGURE 20-5: TYPICAL IPD vs. VDD, WATCHDOG DISABLED (25°C)
2.5
2
Ipd(nA)
Ipd(µA)
1.5
1
0.5
0
2.5
3
3.5
4
4.5
5
5.5
6
VDD(Volts)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 185
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-6: TYPICAL IPD vs. VDD, WATCHDOG ENABLED (25°C)
25
20
IPD (uA)
15
10
5
0
2.5
3
3.5
4
4.5
5
5.5
6
5.5
6
VDD (Volts)
FIGURE 20-7: TYPICAL IPD vs. VDD, WATCHDOG ENABLED (–40°C, 85°C)
35
30
25
IPD (uA)
20
15
10
(-40°C)
5
(+85°C)
0
2.5
3
3.5
4
4.5
5
VDD (Volts)
DS30453A-page 186
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-8: VTH (INPUT THRESHOLD TRIP POINT VOLTAGE) OF I/O PINS vs. VDD
2.00
1.80
VTH (Volts)
1.60
5°C)
1.40
2
Typ (+
1.20
1.00
0.80
0.60
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.5
5.0
6.0
FIGURE 20-9: VIH, VIL OF MCLR, T0CKI AND OSC1 (IN RC MODE) vs. VDD
4.5
4.0
3.5
VIH, VIL (Volts)
VIH
max
3.0
C to
–40°
+85°
C)
(
°C
+25
typ
C)
+85°
o
t
40°C
in (–
VIH
2.5
VIH
m
2.0
°C to +85°C)
VIL max (–40
VIL typ +25°C
1.5
1.0
5°C)
0.5
VIL min (–40°C to +8
0.0
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
6.0
Note: These input pins have Schmitt Trigger input buffers.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 187
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-10: VTH (INPUT THRESHOLD TRIP POINT VOLTAGE) OF OSC1 INPUT
(IN XT, HS, AND LP MODES) vs. VDD
3.4
3.2
3.0
2.8
VTH (Volts)
2.6
)
°C
(+25
Typ
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
2.5
3.0
3.5
4.0
4.5
VDD (Volts)
5.0
5.5
6.0
FIGURE 20-11: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 20 PF, 25°C)
10000
Idd(uA)
1000
5.5V
100
4.5V
3.5V
2.5V
10
100000
1000000
10000000
Freq(Hz)
DS30453A-page 188
Preliminary
1997 Microchip Technology Inc.
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
PIC16C5X
FIGURE 20-12: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 100 PF, 25°C)
10000
Idd(uA)
1000
5.5V
100
4.5V
3.5V
2.5V
10
10000
100000
1000000
10000000
Freq(Hz)
FIGURE 20-13: TYPICAL IDD vs. FREQUENCY (WDT DIS, RC MODE @ 300 PF, 25°C)
10000
Idd(uA)
1000
100
5.5V
4.5V
3.5V
2.5V
10
10000
100000
1000000
Freq(Hz)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 189
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-14: WDT TIMER TIME-OUT
PERIOD vs. VDD
TABLE 20-2:
Typical Capacitance (pF)
50
Pin
45
40
35
WDT period (ms)
INPUT CAPACITANCE FOR
PIC16C54s/C58s
30
Typ +125°C
25
18L PDIP
18L SOIC
RA port
5.0
4.3
RB port
5.0
4.3
MCLR
17.0
17.0
OSC1
4.0
3.5
OSC2/CLKOUT
4.3
3.5
T0CKI
3.2
2.8
All capacitance values are typical at 25°C. A part-to-part
variation of ±25% (three standard deviations) should be
taken into account.
Typ +85°C
20
Typ +25°C
15
Typ –40°C
10
5
2
3
DS30453A-page 190
4
5
VDD (Volts)
6
7
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
FIGURE 20-15: IOH vs. VOH, VDD = 3 V
FIGURE 20-17: IOL vs. VOL, VDD = 3 V
0
45
Max –40°C
40
–5
35
Min +85°C
IOL (mA)
IOH (mA)
30
–10
Typ +25°C
–15
Max –40°C
25
Typ +25°C
20
15
Min +85°C
–20
10
5
–25
0
0.5
1.0
1.5
2.0
2.5
3.0
0
0.0
VOH (Volts)
0.5
1.0
1.5
2.0
2.5
3.0
VOL (Volts)
FIGURE 20-16: IOH vs. VOH, VDD = 5 V
FIGURE 20-18: IOL vs. VOL, VDD = 5 V
90
0
80
70
–10
60
Typ +125°C
Typ +25°C
–20
IOL (mA)
IOH (mA)
Max –40°C
Typ +85°C
Typ +25°C
50
40
Min +85°C
Typ –40°C
30
–30
20
–40
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
10
VOH (Volts)
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
VOL (Volts)
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 191
PIC16C5X
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B
NOTES:
DS30453A-page 192
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
21.0
PACKAGING INFORMATION
21.1
Package Marking Information
18-Lead PDIP
Example
MMMMMMMMMMMMXXX
MMMMMMMMXXXXXXX
AABB CDE
28-Lead Skinny PDIP (.300")
PIC16C56RCI/P456
9523 CBA
Example
MMMMMMMMMMMMMMMMM
XXXXXXXXXXXXXXXXX
PIC16C55RCI/P456
AABB CDE
28-Lead PDIP (.600")
9523 CBA
Example
MMMMMMMMMMMMXXX
MMMMMMMMXXXXXXX
XXXXXXXXXXXXXXX
AABB CDE
PIC16C55XTI/P126
9542 CDA
Legend: MM...M
XX...X
AA
BB
C
Microchip part number information
Customer specific information*
Year code (last two digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
Mask revision number
E
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 193
PIC16C5X
18-Lead SOIC
Example
MMMMMMMMM
XXXXXXXXX
PIC16C54XTI/S0218
AABB CDE
9518 CDK
28-Lead SOIC
Example
MMMMMMMMMMMMMMMMMMXX
XXXXXXXXXXXXXXXXXXXX
AABB CDE
PIC16C57-XT/SO
9515 CBK
20-Lead SSOP
Example
MMMMMMMM
XXXXXXXX
AABB CDE
PIC16C54
XTI/218
9520 CBP
28-Lead SSOP
Example
MMMMMMMMMMMM
XXXXXXXXXXXX
AABB CDE
PIC16C57XT/SS123
9525 CBK
Legend: MM...M
XX...X
AA
BB
C
Microchip part number information
Customer specific information*
Year code (last two digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
Mask revision number
E
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
DS30453A-page 194
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
18-Lead CERDIP Windowed
Example
MMMMMMMM
MMMMMMMM
AABB CDE
PIC16C54
/JW
9501 CBA
28-Lead CERDIP Skinny Windowed
Example
MMMMMMMMMMMMMM
XXXXXXXXXXXXXX
AABBCDE
PIC16C57
/JW
9338 CCT
28-Lead CERDIP Windowed
Example
MMMMMMMMMM
MMMMMM
PIC16C57
/JW
AABB CDE
9538 CBA
Legend: MM...M
XX...X
AA
BB
C
Microchip part number information
Customer specific information*
Year code (last two digits of calendar year)
Week code (week of January 1 is week ‘01’)
Facility code of the plant at which wafer is manufactured
C = Chandler, Arizona, U.S.A.,
S = Tempe, Arizona, U.S.A.
D
Mask revision number
E
Assembly code of the plant or country of origin in which
part was assembled
Note: In the event the full Microchip part number cannot be marked on one line,
it will be carried over to the next line thus limiting the number of available
characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week
code, facility code, mask rev#, and assembly code. For OTP marking
beyond this, certain price adders apply. Please check with your Microchip
Sales Office. For QTP devices, any special marking adders are included in
QTP price.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 195
PIC16C5X
21.2
18-Lead Plastic Dual In-Line (PDIP) - 300 mil
N
α
C
E1 E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
Base
Plane
Seating
Plane
L
B1
A1 A2 A
e1
B
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Symbol
Min
Max
α
0°
A
A1
A2
B
B1
C
D
D1
E
E1
e1
eA
eB
L
N
S
S1
–
0.381
3.048
0.355
1.524
0.203
22.479
20.320
7.620
6.096
2.489
7.620
7.874
3.048
18
0.889
0.127
DS30453A-page 196
Inches
Notes
Min
Max
10°
0°
10°
4.064
–
3.810
0.559
1.524
0.381
23.495
20.320
8.255
7.112
2.591
7.620
9.906
3.556
18
–
–
–
0.015
0.120
0.014
0.060
0.008
0.885
0.800
0.300
0.240
0.098
0.300
0.310
0.120
18
0.035
0.005
0.160
–
0.150
0.022
0.060
0.015
0.925
0.800
0.325
0.280
0.102
0.300
0.390
0.140
18
–
–
Reference
Typical
Reference
Typical
Reference
Preliminary
Notes
Reference
Typical
Reference
Typical
Reference
1997 Microchip Technology Inc.
PIC16C5X
21.3
28-Lead Plastic Dual In-Line (PDIP) - 300 mil
N
α
E1 E
C
eA
eB
Pin No. 1
Indicator
Area
B2
D
B1
S
Base
Plane
Seating
Plane
L
Detail A
B3
A1 A2 A
e1
B
Detail A
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Symbol
Min
Max
α
0°
A
A1
A2
B
B1
B2
B3
C
D
D1
E
E1
e1
eA
eB
L
N
S
3.632
0.381
3.175
0.406
1.016
0.762
0.203
0.203
34.163
33.020
7.874
7.112
2.540
7.874
8.128
3.175
28
0.584
1997 Microchip Technology Inc.
Inches
Notes
Min
Max
10°
0°
10°
4.572
–
3.556
0.559
1.651
1.016
0.508
0.331
35.179
33.020
8.382
7.493
2.540
7.874
9.652
3.683
1.220
0.143
0.015
0.125
0.016
0.040
0.030
0.008
0.008
1.385
1.300
0.310
0.280
0.100
0.310
0.320
0.125
28
0.023
0.180
–
0.140
0.022
0.065
0.040
0.020
0.013
1.395
1.300
0.330
0.295
0.100
0.310
0.380
0.145
0.048
Typical
4 places
4 places
Typical
Reference
Typical
Reference
Preliminary
Notes
Typical
4 places
4 places
Typical
Reference
Typical
Reference
DS30453A-page 197
PIC16C5X
21.4
28-Lead Plastic Dual In-Line (PDIP) - 600 mil
N
α
E1 E
C
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
Base
Plane
Seating
Plane
L
B1
A1 A2 A
e1
B
D1
Package Group: Plastic Dual In-Line (PLA)
Millimeters
Symbol
Min
α
0°
10°
0°
10°
A
A1
A2
B
B1
C
D
D1
E
E1
e1
eA
eB
L
N
S
S1
–
0.508
3.175
0.355
1.270
0.203
35.052
33.020
15.240
12.827
2.489
15.240
15.240
2.921
28
0.889
0.508
5.080
–
4.064
0.559
1.778
0.381
37.084
33.020
15.875
13.970
2.591
15.240
17.272
3.683
28
–
–
–
0.020
0.125
0.014
0.050
0.008
1.380
1.300
0.600
0.505
0.098
0.600
0.600
0.115
28
0.035
0.020
0.200
–
0.160
0.022
0.070
0.015
1.460
1.300
0.625
0.550
0.102
0.600
0.680
0.145
28
–
–
DS30453A-page 198
Max
Inches
Notes
Typical
Typical
Reference
Typical
Reference
Preliminary
Min
Max
Notes
Typical
Typical
Reference
Typical
Reference
1997 Microchip Technology Inc.
PIC16C5X
21.5
18-Lead Plastic Surface Mount (SOIC) - 300 mil
e
B
h x 45°
N
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Seating
Plane
Base
Plane
CP
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Symbol
Min
Max
Inches
Notes
Min
Max
α
0°
8°
0°
8°
A
A1
B
C
D
E
e
H
h
L
N
CP
2.362
0.101
0.355
0.241
11.353
7.416
1.270
10.007
0.381
0.406
18
–
2.642
0.300
0.483
0.318
11.735
7.595
1.270
10.643
0.762
1.143
18
0.102
0.093
0.004
0.014
0.009
0.447
0.292
0.050
0.394
0.015
0.016
18
–
0.104
0.012
0.019
0.013
0.462
0.299
0.050
0.419
0.030
0.045
18
0.004
1997 Microchip Technology Inc.
Reference
Preliminary
Notes
Reference
DS30453A-page 199
PIC16C5X
21.6
28-Lead Plastic Surface Mount (SOIC) - 300 mil
e
B
h x 45°
N
Index
Area
E
H
α
C
Chamfer
h x 45°
L
1
2
3
D
Seating
Plane
Base
Plane
CP
A1
A
Package Group: Plastic SOIC (SO)
Millimeters
Symbol
Min
Max
Inches
Notes
Min
Max
α
0°
8°
0°
8°
A
A1
B
C
D
E
e
H
h
L
N
CP
2.362
0.101
0.355
0.241
17.703
7.416
1.270
10.007
0.381
0.406
28
–
2.642
0.300
0.483
0.318
18.085
7.595
1.270
10.643
0.762
1.143
28
0.102
0.093
0.004
0.014
0.009
0.697
0.292
0.050
0.394
0.015
0.016
28
–
0.104
0.012
0.019
0.013
0.712
0.299
0.050
0.419
0.030
0.045
28
0.004
DS30453A-page 200
Typical
Preliminary
Notes
Typical
1997 Microchip Technology Inc.
PIC16C5X
21.7
20-Lead Plastic Surface Mount (SSOP) - 209 mil
N
Index
area
E
H
α
C
L
1 2 3
B
e
A
Base plane
CP
Seating plane
D
A1
Package Group: Plastic SSOP
Millimeters
Symbol
Min
Max
α
0°
A
A1
B
C
D
E
e
H
L
N
CP
1.730
0.050
0.250
0.130
7.070
5.200
0.650
7.650
0.550
20
-
1997 Microchip Technology Inc.
Inches
Notes
Min
Max
8°
0°
8°
1.990
0.210
0.380
0.220
7.330
5.380
0.650
7.900
0.950
20
0.102
0.068
0.002
0.010
0.005
0.278
0.205
0.026
0.301
0.022
20
-
0.078
0.008
0.015
0.009
0.289
0.212
0.026
0.311
0.037
20
0.004
Reference
Preliminary
Notes
Reference
DS30453A-page 201
PIC16C5X
21.8
28-Lead Plastic Surface Mount (SSOP) - 209 mil
N
Index
area
E
H
α
C
L
1 2 3
B
e
A
Base plane
CP
Seating plane
D
A1
Package Group: Plastic SSOP
Millimeters
Symbol
Min
Max
Inches
Notes
Min
Max
α
0°
8°
0°
8°
A
A1
B
C
D
E
e
H
L
N
CP
1.730
0.050
0.250
0.130
10.070
5.200
0.650
7.650
0.550
28
-
1.990
0.210
0.380
0.220
10.330
5.380
0.650
7.900
0.950
28
0.102
0.068
0.002
0.010
0.005
0.396
0.205
0.026
0.301
0.022
28
-
0.078
0.008
0.015
0.009
0.407
0.212
0.026
0.311
0.037
28
0.004
DS30453A-page 202
Reference
Preliminary
Notes
Reference
1997 Microchip Technology Inc.
PIC16C5X
21.9
18-Lead Ceramic Dual In-Line (CERDIP) with Window - 300 mil
N
α
C
E1 E
eA
eB
Pin No. 1
Indicator
Area
D
S
S1
Base
Plane
Seating
Plane
L
B1
A1 A3 A
e1
B
A2
D1
Package Group: Ceramic Dual In-Line (CDP)
Millimeters
Symbol
Min
Max
α
0°
A
A1
A2
A3
B
B1
C
D
D1
E
E1
e1
eA
eB
L
N
S
S1
—
0.381
3.810
3.810
0.355
1.270
0.203
22.352
20.320
7.620
5.588
2.540
7.366
7.620
3.175
18
0.508
0.381
1997 Microchip Technology Inc.
Inches
Notes
Min
Max
10°
0°
10°
5.080
1.7780
4.699
4.445
0.585
1.651
0.381
23.622
20.320
8.382
7.874
2.540
8.128
10.160
3.810
18
1.397
1.270
—
0.015
0.150
0.150
0.014
0.050
0.008
0.880
0.800
0.300
0.220
0.100
0.290
0.300
0.125
18
0.020
0.015
0.200
0.070
0.185
0.175
0.023
0.065
0.015
0.930
0.800
0.330
0.310
0.100
0.320
0.400
0.150
18
0.055
0.050
Typical
Typical
Reference
Reference
Typical
Preliminary
Notes
Typical
Typical
Reference
Reference
Typical
DS30453A-page 203
PIC16C5X
21.10
28-Lead Ceramic Dual In-Line (CERDIP) with Window - 600 mil
N
E1 E
α
C
Pin No. 1
Indicator
Area
eA
eB
D
S
S1
Base
Plane
Seating
Plane
L
B1
A1 A3 A A2
e1
B
D1
Package Group: Ceramic Dual In-Line (CDP)
Millimeters
Symbol
Min
Max
α
0°
A
A1
A2
A3
B
B1
C
D
D1
E
E1
e1
eA
eB
L
N
S
S1
—
0.381
3.810
3.810
0.355
1.270
0.203
36.195
33.020
15.240
12.954
2.540
14.986
15.240
3.175
28
1.016
0.381
DS30453A-page 204
Inches
Notes
Min
Max
10°
0°
10°
5.461
1.524
4.699
4.445
0.585
1.651
0.381
37.465
33.020
15.875
15.240
2.540
15.748
18.034
3.810
28
2.286
1.778
—
0.015
0.150
0.150
0.014
0.050
0.008
1.425
1.300
0.600
0.510
0.100
0.590
0.600
0.125
28
0.040
0.015
0.215
0.060
0.185
0.175
0.023
0.065
0.015
1.475
1.300
0.625
0.600
0.100
0.620
0.710
0.150
28
0.090
0.070
Typical
Typical
Reference
Typical
Reference
Preliminary
Notes
Typical
Typical
Reference
Typical
Reference
1997 Microchip Technology Inc.
PIC16C5X
APPENDIX A: COMPATIBILITY
To convert code written for PIC16CXX to PIC16C5X,
the user should take the following steps:
1.
2.
3.
4.
5.
6.
7.
Check any CALL, GOTO or instructions that
modify the PC to determine if any program
memory page select operations (PA2, PA1, PA0
bits) need to be made.
Revisit any computed jump operations (write to
PC or add to PC, etc.) to make sure page bits
are set properly under the new scheme.
Eliminate any special function register page
switching. Redefine data variables to reallocate
them.
Verify all writes to STATUS, OPTION, and FSR
registers since these have changed.
Change reset vector to proper value for
processor used.
Remove any use of the ADDLW and SUBLW
instructions.
Rewrite any code segments that use interrupts.
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 205
PIC16C5X
NOTES:
DS30453A-page 206
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
INDEX
A
Absolute Maximum
Ratings ........................... 59, 67, 89, 103, 117, 131, 145, 171
ALU ...................................................................................... 9
Applications .......................................................................... 5
Architectural Overview ......................................................... 9
Assembler
MPASM Assembler .................................................... 56
B
Block Diagram
On-Chip Reset Circuit ................................................ 36
PIC16C5X Series ....................................................... 10
Timer0 ........................................................................ 27
TMR0/WDT Prescaler ................................................ 30
Watchdog Timer ......................................................... 40
Brown-Out Protection Circuit ............................................. 41
ICEPIC Low-Cost PIC16CXXX In-Circuit Emulator ............55
ID Locations ................................................................. 31, 42
INDF ...................................................................................36
INDF Register .....................................................................24
Indirect Data Addressing ....................................................24
Instruction Cycle .................................................................13
Instruction Flow/Pipelining ..................................................13
Instruction Set Summary ....................................................43
K
KEELOQ Evaluation and Programming Tools ...................57
L
Loading of PC .............................................................. 22, 23
M
Carry bit ............................................................................... 9
Clocking Scheme ............................................................... 13
Code Protection ........................................................... 31, 42
Configuration Bits ............................................................... 31
Configuration Word ............................................................ 31
PIC16C52/C54/C54A/C55/C56/C57/C58A ................ 32
PIC16CR54A/C54B/CR54B/C56A/CR56A/
CR57B/C58B/CR58A/CR58B .................................... 31
MCLR .................................................................................36
Memory Map .......................................................................15
PIC16C52 ...................................................................15
PIC16C54s/CR54s/C55s ............................................15
PIC16C56s/CR56s .....................................................15
PIC16C57s/CR57s/C58s ............................................16
Memory Organization .........................................................15
Data Memory ..............................................................17
Program Memory ........................................................15
MP-DriveWay - Application Code Generator ...................57
MPLAB C .........................................................................57
MPLAB Integrated Development
Environment Software ........................................................56
D
O
DC and AC Characteristics - PIC16C54/55/56/57 ............. 81
DC and AC Characteristics PIC16C54A/CR57B/C58A/CR58A ................................... 159
DC and AC Characteristics PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B ............ 183
DC Characteristics
......... 60, 61, 69, 70, 71, 72, 73, 91, 105, 119, 133, 147, 173
Development Support ........................................................ 55
Development Tools ............................................................ 55
Device Varieties ................................................................... 7
Digit Carry bit ....................................................................... 9
One-Time-Programmable (OTP) Devices ............................7
OPTION ..............................................................................36
OPTION Register ...............................................................21
OSC selection .....................................................................31
Oscillator Configurations ....................................................33
Oscillator Types
HS ...............................................................................33
LP ...............................................................................33
RC ..............................................................................33
XT ...............................................................................33
E
Package Marking Information .......................................... 193
Packaging Information ..................................................... 193
PC .......................................................................................22
PCL .....................................................................................36
PIC16C54/55/56/57 Product Identification System ......... 216
PIC16C5X Product Identification System ........................ 215
PICDEM-1 Low-Cost PIC16/17 Demo Board .....................56
PICDEM-2 Low-Cost PIC16CXX Demo Board ...................56
PICDEM-3 Low-Cost PIC16CXXX Demo Board ................56
PICMASTER In-Circuit Emulator ......................................55
PICSTART Plus Entry Level Development System .........55
Pin Configurations ................................................................2
Pinout Description - PIC16C52s, PIC16C54s,
PIC16CR54s, PIC16C56s, PIC16CR56s,
PIC16C58s, PIC16CR58s ..................................................11
Pinout Description - PIC16C55s, PIC16C57s,
PIC16CR57s .......................................................................12
POR
Device Reset Timer (DRT) .................................. 31, 39
PD ........................................................................ 35, 41
Power-On Reset (POR) ................................. 31, 36, 37
TO ........................................................................ 35, 41
PORTA ........................................................................ 25, 36
PORTB ........................................................................ 25, 36
C
Electrical Characteristics
PIC16C52 .................................................................. 59
PIC16C54/55/56/57 ................................................... 67
PIC16C54A .............................................................. 103
PIC16C54B/CR54B/C56A/CR56A/C58B/CR58B .... 171
PIC16C58A .............................................................. 131
PIC16CR54A ............................................................. 89
PIC16CR57B ........................................................... 117
PIC16CR58A ........................................................... 145
External Power-On Reset Circuit ....................................... 37
F
Family of Devices
PIC16C5X .................................................................... 6
Features ............................................................................... 1
FSR .................................................................................... 36
FSR Register ..................................................................... 24
Fuzzy Logic Dev. System (fuzzyTECH-MP) .................... 57
I
I/O Interfacing .................................................................... 25
I/O Ports ............................................................................. 25
I/O Programming Considerations ....................................... 26
1997 Microchip Technology Inc.
P
Preliminary
DS30453A-page 207
PIC16C5X
PORTC ......................................................................... 25, 36
Power-Down Mode (SLEEP) .............................................. 42
Prescaler ............................................................................ 30
PRO MATE II Universal Programmer .............................. 55
Program Counter ................................................................ 22
Q
Q cycles ............................................................................. 13
Quick-Turnaround-Production (QTP) Devices ..................... 7
R
RC Oscillator ...................................................................... 34
Read Only Memory (ROM) Devices ..................................... 7
Read-Modify-Write ............................................................. 26
Register File Map
PIC16C52, PIC16C54s, PIC16CR54s,
PIC16C55s, PIC16C56s, PIC16CR56s ..................... 17
PIC16C57s/CR57s ..................................................... 18
PIC16C58s/CR58s ..................................................... 18
Registers
Special Function ........................................................ 19
Reset ............................................................................ 31, 35
Reset on Brown-Out ........................................................... 41
LIST OF EXAMPLES
Example 3-1: Instruction Pipeline Flow ............................ 13
Example 4-1: Indirect Addressing..................................... 24
Example 4-2: How To Clear RAM Using Indirect
Addressing ................................................. 24
Example 5-1: Read-Modify-Write Instructions on an
I/O Port ....................................................... 26
Example 6-1: Changing Prescaler (Timer0→WDT).......... 30
Example 6-2: Changing Prescaler (WDT→Timer0).......... 30
LIST OF FIGURES
Figure 3-1:
Figure 3-2:
Figure 4-1:
Figure 4-2:
Figure 4-3:
Figure 4-4:
Figure 4-5:
S
SEEVAL Evaluation and Programming System .............. 57
Serialized Quick-Turnaround-Production (SQTP)
Devices ................................................................................ 7
SLEEP .......................................................................... 31, 42
Software Simulator (MPLAB SIM) ................................... 57
Special Features of the CPU .............................................. 31
Special Function Registers ................................................ 19
Stack .................................................................................. 23
STATUS ............................................................................. 36
STATUS Register ........................................................... 9, 20
Figure 4-6:
Figure 4-7:
Figure 4-8:
Figure 4-9:
Figure 4-10:
Figure 4-11:
Figure 4-12:
T
Timer0
Switching Prescaler Assignment ................................ 30
Timer0 (TMR0) Module .............................................. 27
TMR0 with External Clock .......................................... 29
Timing Diagrams and
Specifications ................. 63, 75, 97, 111, 125, 139, 153, 178
Timing Parameter Symbology and
Load Conditions ............. 62, 74, 96, 110, 124, 138, 152, 177
TMR0 ................................................................................. 36
TRIS ................................................................................... 36
TRIS Registers ................................................................... 25
U
UV Erasable Devices ........................................................... 7
Figure 4-13:
Figure 5-1:
Figure 5-2:
Figure 6-1:
Figure 6-2:
Figure 6-3:
Figure 6-4:
Figure 6-5:
Figure 6-6:
Figure 7-1:
W
W ........................................................................................ 36
Wake-up from SLEEP ........................................................ 42
Watchdog Timer (WDT) ............................................... 31, 39
Period ......................................................................... 39
Programming Considerations .................................... 39
Figure 7-2:
Z
Figure 7-4:
Zero bit ................................................................................. 9
Figure 7-5:
Figure 7-3:
Figure 7-6:
Figure 7-7:
DS30453A-page 208
Preliminary
PIC16C5X Series Block Diagram ............... 10
Clock/Instruction Cycle ............................... 13
PIC16C52 Program Memory Map
and Stack ................................................... 15
PIC16C54s/CR54s/C55s
Program Memory Map and Stack............... 15
PIC16C56s/CR56s Program Memory
Map and Stack ........................................... 15
PIC16C57s/CR57s/C58s/CR58s
Program Memory Map and Stack............... 16
PIC16C52, PIC16C54s, PIC16CR54s,
PIC16C55s, PIC16C56s, PIC16CR56s
Register File Map ....................................... 17
PIC16C57s/CR57s Register File Map ........ 18
PIC16C58s/CR58s Register File Map ........ 18
STATUS Register (Address:03h) ............... 20
OPTION Register ....................................... 21
Loading of PC Branch Instructions PIC16C52, PIC16C54s, PIC16CR54s,
PIC16C55s ................................................. 22
Loading of PC Branch Instructions PIC16C56s/PIC16CR56s ........................... 22
Loading of PC Branch Instructions PIC16C57s/PIC16CR57s, and
PIC16C58s/PIC16CR58s ........................... 23
Direct/Indirect Addressing .......................... 24
Equivalent Circuit
for a Single I/O Pin ..................................... 25
Successive I/O Operation........................... 26
Timer0 Block Diagram ................................ 27
Electrical Structure of T0CKI Pin ................ 27
Timer0 Timing: Internal Clock/
No Prescale ................................................ 28
Timer0 Timing: Internal Clock/
Prescale 1:2 ............................................... 28
Timer0 Timing With External Clock ............ 29
Block Diagram of the Timer0/WDT
Prescaler .................................................... 30
Configuration Word for
PIC16CR54A/C54B/CR54B/C56A/
CR56A/CR57B/C58B/CR58A/CR58B ........ 31
Configuration Word for
PIC16C52/C54/C54A/C55/C56/
C57/C58A ................................................... 32
Crystal Operation (or Ceramic Resonator)
(HS, XT or LP OSC Configuration)............. 33
External Clock Input Operation
(HS, XT or LP OSC Configuration)............. 33
External Parallel Resonant Crystal
Oscillator Circuit (using XT, HS or
LP oscillator mode)..................................... 34
External Series Resonant Crystal
Oscillator Circuit (using XT, HS or
LP oscillator mode)..................................... 34
RC Oscillator Mode .................................... 35
1997 Microchip Technology Inc.
PIC16C5X
Figure 7-8:
Figure 7-9:
Figure 7-10:
Figure 7-11:
Figure 7-12:
Figure 7-13:
Figure 7-14:
Figure 7-15:
Figure 8-1:
Figure 10-1:
Figure 10-2:
Figure 10-3:
Figure 10-4:
Figure 10-5:
Figure 11-1:
Figure 11-2:
Figure 11-3:
Figure 11-4:
Figure 11-5:
Figure 12-1:
Figure 12-2:
Figure 12-3:
Figure 12-4:
Figure 12-5:
Figure 12-6:
Figure 12-7:
Figure 12-8:
Figure 12-9:
Figure 12-10:
Figure 12-11:
Figure 12-12:
Figure 12-13:
Figure 12-14:
Figure 12-15:
Figure 12-16:
Figure 12-17:
Figure 12-18:
Simplified Block Diagram of On-Chip
Reset Circuit ............................................... 36
External Power-On Reset Circuit
(For Slow VDD Power-Up)........................... 37
Time-Out Sequence on Power-Up
(MCLR Not Tied to VDD) ............................. 38
Time-Out Sequence on Power-Up
(MCLR Tied to VDD): Fast VDD
Rise Time.................................................... 38
Time-Out Sequence on Power-Up
(MCLR Tied to VDD): Slow VDD
Rise Time.................................................... 38
Watchdog Timer Block Diagram ................. 40
Brown-Out Protection Circuit 1 ................... 41
Brown-Out Protection Circuit 2 ................... 41
General Format for Instructions .................. 43
Load Conditions - PIC16C52 ...................... 62
External Clock Timing - PIC16C52 ............. 63
CLKOUT and I/O Timing - PIC16C52......... 64
Reset and Device Reset Timer Timing PIC16C52 ................................................... 65
Timer0 Clock Timings - PIC16C52 ............. 66
Load Conditions - PIC16C54/55/56/57 ....... 74
External Clock Timing PIC16C54/55/56/57 .................................... 75
CLKOUT and I/O Timing PIC16C54/55/56/57 .................................... 77
Reset, Watchdog Timer, and
Device Reset Timer Timing PIC16C54/55/56/57 .................................... 78
Timer0 Clock Timings PIC16C54/55/56/57 .................................... 79
Typical RC Oscillator Frequency vs.
Temperature ............................................... 81
Typical RC Oscillator Frequency vs.
VDD, CEXT = 20 PF...................................... 82
Typical RC Oscillator Frequency vs.
VDD, CEXT = 100 PF.................................... 82
Typical RC Oscillator Frequency vs.
VDD, CEXT = 300 PF.................................... 82
Typical IPD vs. VDD, Watchdog Disabled .... 83
Maximum IPD vs. VDD,
Watchdog Disabled..................................... 83
Typical IPD vs. VDD, Watchdog Enabled..... 83
Maximum IPD vs. VDD,
Watchdog Enabled ..................................... 83
VTH (Input Threshold Voltage) of
I/O Pins vs. VDD .......................................... 84
VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD ................................. 84
VTH (Input Threshold Voltage) of
OSC1 Input (in XT, HS, and LP modes)
vs. VDD........................................................ 84
Typical IDD vs. Frequency
(External Clock, 25°C) ................................ 85
Maximum IDD vs. Frequency
(External Clock, –40°C to +85°C) ............... 85
Maximum IDD vs. Frequency
(External Clock –55°C to +125°C) .............. 86
WDT Timer Time-out Period vs. VDD .......... 86
Transconductance (gm) of
HS Oscillator vs. VDD .................................. 86
Transconductance (gm) of
LP Oscillator vs. VDD .................................. 87
IOH vs. VOH, VDD = 3 V ............................... 87
1997 Microchip Technology Inc.
Figure 12-19: Transconductance (gm) of
XT Oscillator vs. VDD ...................................87
Figure 12-20: IOH vs. VOH, VDD = 5 V................................87
Figure 12-21: IOL vs. VOL, VDD = 3 V.................................88
Figure 12-22: IOL vs. VOL, VDD = 5 V.................................88
Figure 13-1: Load Conditions ..........................................96
Figure 13-2: External Clock Timing - PIC16CR54A.........97
Figure 13-3: CLKOUT and I/O Timing - PIC16CR54A ....99
Figure 13-4: Reset, Watchdog Timer, and Device
Reset Timer Timing - PIC16CR54A ......... 100
Figure 13-5: Timer0 Clock Timings - PIC16CR54A...... 101
Figure 14-1: Load Conditions - PIC16C54A ................. 110
Figure 14-2: External Clock Timing - PIC16C54A ........ 111
Figure 14-3: CLKOUT and I/O Timing - PIC16C54A .... 113
Figure 14-4: Reset, Watchdog Timer, and
Device Reset Timer Timing PIC16C54A .............................................. 114
Figure 14-5: Timer0 Clock Timings - PIC16C54A ........ 115
Figure 15-1: Load Conditions ....................................... 124
Figure 15-2: External Clock Timing - PIC16CR57B...... 125
Figure 15-3: CLKOUT and I/O Timing PIC16CR57B............................................ 127
Figure 15-4: Reset, Watchdog Timer, and Device
Reset Timer Timing - PIC16CR57B ......... 128
Figure 15-5: Timer0 Clock Timings - PIC16CR57B...... 129
Figure 16-1: Load Conditions - PIC16C58A,
PIC16LV58A............................................. 138
Figure 16-2: External Clock Timing - PIC16C58A ........ 139
Figure 16-3: CLKOUT and I/O Timing - PIC16C58A .... 141
Figure 16-4: Reset, Watchdog Timer, and
Device Reset Timer Timing PIC16C58A .............................................. 142
Figure 16-5: Timer0 Clock Timings - PIC16C58A ........ 143
Figure 17-1: Load Conditions - PIC16CR58A............... 152
Figure 17-2: External Clock Timing - PIC16CR58A...... 153
Figure 17-3: CLKOUT and I/O Timing PIC16CR58A............................................ 155
Figure 17-4: Reset, Watchdog Timer, and
Device Reset Timer Timing PIC16CR58A............................................ 156
Figure 17-5: Timer0 Clock Timings - PIC16CR58A...... 157
Figure 18-1: Typical RC Oscillator Frequency vs.
Temperature............................................. 159
Figure 18-2: Typical RC Oscillator Frequency vs.
VDD, CEXT = 20 PF ................................... 160
Figure 18-3: Typical RC Oscillator Frequency vs.
VDD, CEXT = 100 PF ................................. 160
Figure 18-4: Typical RC Oscillator Frequency vs.
VDD, CEXT = 300 PF ................................. 161
Figure 18-5: Typical IPD vs. VDD, Watchdog
Disabled (25°C) ........................................ 161
Figure 18-6: Typical IPD vs. VDD, Watchdog
Enabled (25°C)......................................... 162
Figure 18-7: VTH (Input Threshold Voltage) of
I/O Pins vs. VDD ....................................... 162
Figure 18-8: VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD ............................... 163
Figure 18-9: VTH (Input Threshold Voltage) of
OSC1 Input (in XT, HS, and LP modes)
vs. VDD ..................................................... 163
Figure 18-10: Typical IDD vs. Frequency
(WDT dis, RC Mode @ 20 PF, 25°C) ....... 164
Figure 18-11: Maximum IDD vs. Frequency
(WDT Dis, RC Mode @ 20 PF,
–40°C to +85°C) ....................................... 164
Preliminary
DS30453A-page 209
PIC16C5X
Figure 18-12: Typical IDD vs. Frequency
(WDT Dis, RC Mode @ 100 PF, 25°C) ..... 165
Figure 18-13: Maximum IDD vs. Frequency
(WDT Dis, RC Mode @ 100 PF,
–40°C to +85°C) ....................................... 165
Figure 18-14: Typical IDD vs. Frequency
(WDT Dis, RC Mode @ 300 PF, 25°C) ..... 166
Figure 18-15: Maximum IDD vs. Frequency
(WDT Dis, RC Mode @ 300 PF,
–40°C to +85°C) ....................................... 166
Figure 18-16: WDT Timer Time-out Period vs. VDD ........ 167
Figure 18-17: Transconductance (gm) of
HS Oscillator vs. VDD ................................ 168
Figure 18-18: Transconductance (gm) of
LP Oscillator vs. VDD ................................ 168
Figure 18-19: Transconductance (gm) of
XT Oscillator vs. VDD ................................ 168
Figure 18-20: IOH vs. VOH, VDD = 3 V ............................. 169
Figure 18-21: IOH vs. VOH, VDD = 5 V ............................. 169
Figure 18-22: IOL vs. VOL, VDD = 3 V .............................. 169
Figure 18-23: IOL vs. VOL, VDD = 5 V .............................. 169
Figure 19-1: Load Conditions PIC16C54B/CR54B/C56A/CR56A/
C58B/CR58B, PIC16CR5X....................... 177
Figure 19-2: External Clock Timing PIC16C5X, PIC16CR5X ........................... 178
Figure 19-3: CLKOUT and I/O Timing PIC16C5X, PIC16CR5X ........................... 180
Figure 19-4: Reset, Watchdog Timer, and
Device Reset Timer Timing PIC16C5X, PIC16CR5X ........................... 181
Figure 19-5: Timer0 Clock Timings PIC16C5X, PIC16CR5X ........................... 182
Figure 20-1: Typical RC Oscillator Frequency vs.
Temperature ............................................. 183
Figure 20-2: Typical RC Oscillator Frequency vs.
VDD, CEXT = 20 PF .................................... 184
Figure 20-3: Typical RC Oscillator Frequency vs.
VDD, CEXT = 100 PF .................................. 184
Figure 20-4: Typical RC Oscillator Frequency vs.
VDD, CEXT = 300 PF .................................. 185
Figure 20-5: Typical IPD vs. VDD, Watchdog
Disabled (25°C) ........................................ 185
Figure 20-6: Typical IPD vs. VDD, Watchdog
Enabled (25°C) ......................................... 186
Figure 20-7: Typical IPD vs. VDD, Watchdog
Enabled (–40°C, 85°C) ............................. 186
Figure 20-8: VTH (Input Threshold Trip Point Voltage)
of I/O Pins vs. VDD .................................... 187
Figure 20-9: VIH, VIL of MCLR, T0CKI and OSC1
(in RC Mode) vs. VDD ............................... 187
Figure 20-10: VTH (Input Threshold Trip Point Voltage)
of OSC1 Input (in XT, HS, and LP modes)
vs. VDD ...................................................... 188
Figure 20-11: Typical IDD vs. Frequency
(WDT dis, RC Mode @ 20 PF, 25°C)........ 188
Figure 20-12: Typical IDD vs. Frequency
(WDT Dis, RC Mode @ 100 PF, 25°C) ..... 189
Figure 20-13: Typical IDD vs. Frequency
(WDT Dis, RC Mode @ 300 PF, 25°C) ..... 189
Figure 20-14: WDT Timer Time-out Period vs. VDD ........ 190
Figure 20-15: IOH vs. VOH, VDD = 3 V ............................. 191
Figure 20-16: IOH vs. VOH, VDD = 5 V ............................. 191
Figure 20-17: IOL vs. VOL, VDD = 3 V .............................. 191
Figure 20-18: IOL vs. VOL, VDD = 5 V .............................. 191
DS30453A-page 210
LIST OF TABLES
Table 1-1:
Table 3-1:
Table 3-2:
Table 4-1:
Table 5-1:
Table 6-1:
Table 7-1:
Table 7-2:
Table 7-3:
Table 7-4:
Table 7-5:
Table 7-6:
Table 7-7:
Table 8-1:
Table 8-2:
Table 9-1:
Table 10-1:
Table 10-2:
Table 10-3:
Table 10-4:
Table 11-1:
Table 11-2:
Table 11-3:
Table 11-4:
Table 11-5:
Table 11-6:
Table 12-1:
Table 12-2:
Table 12-3:
Table 13-1:
Table 13-2:
Table 13-3:
Table 13-4:
Table 13-5:
Table 14-1:
Preliminary
PIC16C5X Family of Devices ....................... 6
Pinout Description - PIC16C52,
PIC16C54s, PIC16CR54s, PIC16C56s,
PIC16CR56s, PIC16C58s, PIC16CR58s ... 11
Pinout Description - PIC16C55s,
PIC16C57s, PIC16CR57s .......................... 12
Special Function Register Summary .......... 19
Summary of Port Registers ........................ 25
Registers Associated With Timer0 ............. 28
Capacitor Selection
For Ceramic Resonators - PIC16C5X,
PIC16CR5X ................................................ 33
Capacitor Selection For Crystal
Oscillator - PIC16C5X, PIC16CR5X........... 33
Reset Conditions for Special Registers ...... 36
Reset Conditions for All Registers.............. 36
Summary of Registers Associated
with the Watchdog Timer............................ 40
TO/PD Status After Reset .......................... 41
Events Affecting TO/PD Status Bits ........... 41
OPCODE Field Descriptions ...................... 43
Instruction Set Summary ............................ 44
Development Tools From Microchip........... 58
External Clock Timing Requirements PIC16C52 ................................................... 63
CLKOUT and I/O Timing Requirements PIC16C52 ................................................... 64
Reset and Device Reset Timer PIC16C52 ................................................... 65
Timer0 Clock Requirements PIC16C52 ................................................... 66
Cross Reference of Device Specs for
Oscillator Configurations (RC, XT & 10)
and Frequencies of Operation
(Commercial Devices) ................................ 68
Cross Reference of Device Specs for
Oscillator Configurations (HS, LP & JW)
and Frequencies of Operation
(Commercial Devices) ................................ 68
External Clock Timing Requirements PIC16C54/55/56/57 .................................... 75
CLKOUT and I/O Timing Requirements PIC16C54/55/56/57 .................................... 77
Reset, Watchdog Timer, and Device
Reset Timer - PIC16C54/55/56/57 ............. 78
Timer0 Clock Requirements PIC16C54/55/56/57 .................................... 79
RC Oscillator Frequencies ......................... 81
Input Capacitance for PIC16C54/56........... 88
Input Capacitance for PIC16C55/57........... 88
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices) ........... 90
External Clock Timing Requirements PIC16CR54A .............................................. 97
CLKOUT and I/O Timing Requirements PIC16CR54A .............................................. 99
Reset, Watchdog Timer, and Device
Reset Timer - PIC16CR54A ..................... 100
Timer0 Clock Requirements PIC16CR54A ............................................ 101
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices) ......... 104
1997 Microchip Technology Inc.
PIC16C5X
Table 14-2:
Table 14-3:
Table 14-4:
Table 14-5:
Table 15-1:
Table 15-2:
Table 15-3:
Table 15-4:
Table 15-5:
Table 16-1:
Table 16-2:
Table 16-3:
Table 16-4:
Table 16-5:
Table 17-1:
Table 17-2:
Table 17-3:
Table 17-4:
Table 17-5:
Table 18-1:
Table 18-2:
Table 19-1:
Table 19-2:
Table 19-3:
Table 19-4:
Table 19-5:
Table 20-1:
Table 20-2:
External Clock Timing Requirements PIC16C54A............................................... 111
CLKOUT and I/O Timing Requirements PIC16C54A............................................... 113
Reset, Watchdog Timer, and Device
Reset Timer - PIC16C54A ........................ 114
Timer0 Clock Requirements PIC16C54A............................................... 115
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices).......... 118
External Clock Timing Requirements PIC16CR57B ............................................ 125
CLKOUT and I/O Timing Requirements PIC16CR57B ............................................ 127
Reset, Watchdog Timer, and Device
Reset Timer - PIC16CR57B ..................... 128
Timer0 Clock Requirements PIC16CR57B ............................................ 129
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices).......... 132
External Clock Timing Requirements PIC16C58A............................................... 139
CLKOUT and I/O Timing Requirements PIC16C58A............................................... 141
Reset, Watchdog Timer, and Device
Reset Timer - PIC16C58A ........................ 142
Timer0 Clock Requirements PIC16C58A............................................... 143
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices).......... 146
External Clock Timing Requirements PIC16CR58A ............................................ 153
CLKOUT and I/O Timing Requirements PIC16CR58A ............................................ 155
Reset, Watchdog Timer, and Device
Reset Timer - PIC16CR58A ..................... 156
Timer0 Clock Requirements PIC16CR58A ............................................ 157
RC Oscillator Frequencies........................ 159
Input Capacitance for
PIC16C54A/C58A..................................... 167
Cross Reference of Device Specs for
Oscillator Configurations and Frequencies
of Operation (Commercial Devices).......... 172
External Clock Timing Requirements PIC16C5X, PIC16CR5X ........................... 178
CLKOUT and I/O Timing Requirements PIC16C5X, PIC16CR5X ........................... 180
Reset, Watchdog Timer, and Device
Reset Timer - PIC16C5X, PIC16CR5X .... 181
Timer0 Clock Requirements - PIC16C5X,
PIC16CR5X .............................................. 182
RC Oscillator Frequencies........................ 183
Input Capacitance for
PIC16C54s/C58s ...................................... 190
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 211
PIC16C5X
NOTES:
DS30453A-page 212
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
ON-LINE SUPPORT
Microchip provides two methods of on-line support.
These are the Microchip BBS and the Microchip World
Wide Web (WWW) site.
Use Microchip's Bulletin Board Service (BBS) to get
current information and help about Microchip products.
Microchip provides the BBS communication channel
for you to use in extending your technical staff with
microcontroller and memory experts.
To provide you with the most responsive service possible,
the Microchip systems team monitors the BBS, posts
the latest component data and software tool updates,
provides technical help and embedded systems
insights, and discusses how Microchip products provide project solutions.
The web site, like the BBS, is used by Microchip as a
means to make files and information easily available to
customers. To view the site, the user must have access
to the Internet and a web browser, such as Netscape or
Microsoft Explorer. Files are also available for FTP
download from our FTP site.
Connecting to the Microchip Internet Web Site
The Microchip web site is available by using your
favorite Internet browser to attach to:
www.microchip.com
The file transfer site is available by using an FTP service to connect to:
ftp://ftp.futureone.com/pub/microchip
The web site and file transfer site provide a variety of
services. Users may download files for the latest
Development Tools, Data Sheets, Application Notes,
User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also
available, including listings of Microchip sales offices,
distributors and factory representatives. Other data
available for consideration is:
• Latest Microchip Press Releases
• Technical Support Section with Frequently Asked
Questions
• Design Tips
• Device Errata
• Job Postings
• Microchip Consultant Program Member Listing
• Links to other useful web sites related to
Microchip Products
Connecting to the Microchip BBS
Connect worldwide to the Microchip BBS using either
the Internet or the CompuServe communications network.
Internet:
You can telnet or ftp to the Microchip BBS at the
address: mchipbbs.microchip.com
CompuServe Communications Network:
When using the BBS via the Compuserve Network,
in most cases, a local call is your only expense. The
Microchip BBS connection does not use CompuServe
membership services, therefore you do not need
CompuServe membership to join Microchip's BBS.
There is no charge for connecting to the Microchip BBS.
1997 Microchip Technology Inc.
The procedure to connect will vary slightly from country
to country. Please check with your local CompuServe
agent for details if you have a problem. CompuServe
service allow multiple users various baud rates
depending on the local point of access.
The following connect procedure applies in most locations.
1. Set your modem to 8-bit, No parity, and One stop
(8N1). This is not the normal CompuServe setting
which is 7E1.
2. Dial your local CompuServe access number.
3. Depress the <Enter> key and a garbage string will
appear because CompuServe is expecting a 7E1
setting.
4. Type +, depress the <Enter> key and “Host Name:”
will appear.
5. Type MCHIPBBS, depress the <Enter> key and you
will be connected to the Microchip BBS.
In the United States, to find the CompuServe phone
number closest to you, set your modem to 7E1 and dial
(800) 848-4480 for 300-2400 baud or (800) 331-7166
for 9600-14400 baud connection. After the system
responds with “Host Name:”, type NETWORK, depress
the <Enter> key and follow CompuServe's directions.
For voice information (or calling from overseas), you
may call (614) 723-1550 for your local CompuServe
number.
Microchip regularly uses the Microchip BBS to distribute
technical information, application notes, source code,
errata sheets, bug reports, and interim patches for
Microchip systems software products. For each SIG, a
moderator monitors, scans, and approves or disapproves files submitted to the SIG. No executable files
are accepted from the user community in general to
limit the spread of computer viruses.
Systems Information and Upgrade Hot Line
The Systems Information and Upgrade Line provides
system users a listing of the latest versions of all of
Microchip's development systems software products.
Plus, this line provides information on how customers
can receive any currently available upgrade kits.The
Hot Line Numbers are:
1-800-755-2345 for U.S. and most of Canada, and
1-602-786-7302 for the rest of the world.
970301
Trademarks: The Microchip name, logo, PIC, PICSTART,
PICMASTER and PRO MATE are registered trademarks
of Microchip Technology Incorporated in the U.S.A. and
other countries. FlexROM, MPLAB and fuzzyLAB, are
trademarks and SQTP is a service mark of Microchip in
the U.S.A.
fuzzyTECH is a registered trademark of Inform Software
Corporation. IBM, IBM PC-AT are registered trademarks
of International Business Machines Corp. Pentium is a
trademark of Intel Corporation. Windows is a trademark
and MS-DOS, Microsoft Windows are registered trademarks of Microsoft Corporation. CompuServe is a registered trademark of CompuServe Incorporated.
All other trademarks mentioned herein are the property of
their respective companies.
Preliminary
DS30453A-page 213
PIC16C5X
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (602) 786-7578.
Please list the following information, and use this outline to provide us with your comments about this Data Sheet.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Device: PIC16C5X
Y
N
Literature Number: DS30453A
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this data sheet easy to follow? If not, why?
4. What additions to the data sheet do you think would enhance the structure and subject?
5. What deletions from the data sheet could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
8. How would you improve our software, systems, and silicon products?
DS30453A-page 214
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
PIC16C5X PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
Device
Frequency
Range
X
-XX
Frequency Temperature
Range
Range
/XX
XXX
Package
Pattern
PIC16C5X(2), PIC16C5XT(3)
PIC16LC5X(2), PIC16LC5XT(3)
PIC16CR5X(2), PIC16CR5XT(3)
PIC16LCR5X(2), PIC16LCR5XT(3)
PIC16LV5X(2), PIC16LV5XT(3)
a)
b)
c)
02
04
10
20
b(1)
= 2 MHz
= 4 MHz
= 10 MHz
= 20 MHz
= No type for JW(4) devices
Temperature
Range
b(1)
I
E
= 0°C to +70°C
= -40°C to +85°C
= -40°C to +125°C
Package
JW
P
SO
SP
SS
= Windowed CERDIP
= PDIP
= SOIC (Gull Wing, 300 mil body)
= Skinny PDIP (28-pin, 300 mil body)
= SSOP (209 mil body)
Pattern
3-digit Pattern Code for QTP, ROM (blank otherwise)
1997 Microchip Technology Inc.
Examples:
(Commercial)
(Industrial)
(Automotive)
Preliminary
PIC16C54A -04/P 301 = Commercial
temp., PDIP package, 4MHz, normal VDD
limitis, QTP pattern #301.
PIC16LC58A - 04I/SO = Industrial temp.,
SOIC package, 4MHz, Extended VDD
limits.
PIC16CR54A - 10I/P355 = ROM program
memory, Industrial temp., PDIP package,
10MHz, normal VDD limits.
Note 1: b = blank
2: C
= Standard VDD range
LC = Extended VDD range
CR = ROM Version, Standard VDD
range
LCR = ROM Version, Extended VDD
range
LV = Low Voltage VDD range
3: T = in tape and reel - SOIC, SSOP
packages only.
4: UV erasable devices are tested to all
available voltage/frequency options.
Erased devices are oscillator type
04. The user can select 04, 10 or 20
oscillators by programmng the appropriate configuration bits.
DS30453A-page 215
PIC16C5X
PIC16C54/55/56/57 PRODUCT IDENTIFICATION SYSTEM
To order or obtain information (e.g., on pricing or delivery) refer to the factory or the listed sales office.
PART NO.
-XX
Device
Oscillator
Type
Device
X
Temperature
Range
/XX
XXX
Package
Pattern
Examples:
a)
PIC16C54, PIC16C54T(2)
PIC16C55, PIC16C55T(2)
PIC16C56, PIC16C56T(2)
PIC16C57, PIC16C57T(2)
b)
c)
Oscillator Type
RC
LP
XT
HS
10
b(1)
= Resistor Capacitor
= Low Power Crystal
= Standard Crystal/Resonator
= High Speed Crystal
= 10 MHz Crystal
= No type for JW(3) devices
Temperature
Range
b(1)
I
E
= 0°C to +70°C (Commercial)
= -40°C to +85°C (Industrial)
= -40°C to +125°C (Automotive)
Package
JW
P
S
SO
SP
SS
= Windowed CERDIP
= PDIP
= Die in Waffle Pack
= SOIC (Gull Wing, 300 mil body)
= Skinny PDIP (28 pin, 300 mil body)
= SSOP (209 mil body)
Pattern
3-digit Pattern Code for QTP (blank otherwise)
d)
PIC16C54 - XT/PXXX = "XT" oscillator,
commercial temp., PDIP, QTP pattern.
PIC16C55 - XTI/SO = "XT" oscillator,
industrial temp., SOIC (OTP device)
PIC16C55 /JW = Commercial temp.
CERDIP with window.
PIC16C57 - RC/S = "RC" oscillator, commercial temp., dice in waffle pack.
Note 1: b = blank
2: T = in tape and reel - SOIC, SSOP
packages only.
3: UV erasable devices are tested to all
available voltage/frequency options.
Erased devices are oscillator type RC.
The user can select RC, LP, XT or HS
oscillators by programming the appropriate configuration bits.
Sales and Support
Products supported by a preliminary Data Sheet may possibly have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. Your local Microchip sales office (see below)
2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
3. The Microchip’s Bulletin Board, via your local CompuServe number (CompuServe membership NOT required).
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
For latest version information and upgrade kits for Microchip Development Tools, please call 1-800-755-2345 or 1-602-786-7302.
DS30453A-page 216
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
NOTES:
1997 Microchip Technology Inc.
Preliminary
DS30453A-page 217
PIC16C5X
NOTES:
DS30453A-page 218
Preliminary
1997 Microchip Technology Inc.
PIC16C5X
NOTES:
1997 Microchip Technology Inc.
DS30453A-page 219
WORLDWIDE SALES & SERVICE
AMERICAS
ASIA/PACIFIC
EUROPE
Corporate Office
Hong Kong
United Kingdom
Microchip Technology Inc.
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 602-786-7200 Fax: 602-786-7277
Technical Support: 602 786-7627
Web: http://www.microchip.com
Microchip Asia Pacific
RM 3801B, Tower Two
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2-401-1200 Fax: 852-2-401-3431
Arizona Microchip Technology Ltd.
Unit 6, The Courtyard
Meadow Bank, Furlong Road
Bourne End, Buckinghamshire SL8 5AJ
Tel: 44-1628-851077 Fax: 44-1628-850259
Atlanta
India
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Tel: 770-640-0034 Fax: 770-640-0307
Microchip Technology India
No. 6, Legacy, Convent Road
Bangalore 560 025, India
Tel: 91-80-299-4036 Fax: 91-80-559-9840
Arizona Microchip Technology SARL
Zone Industrielle de la Bonde
2 Rue du Buisson aux Fraises
91300 Massy, France
Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Boston
Korea
Germany
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508-480-9990 Fax: 508-480-8575
Microchip Technology Korea
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea
Tel: 82-2-554-7200 Fax: 82-2-558-5934
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 Müchen, Germany
Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Shanghai
Arizona Microchip Technology SRL
Centro Direzionale Colleone
Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Milan, Italy
Tel: 39-39-6899939 Fax: 39-39-6899883
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071 Fax: 630-285-0075
Dallas
Microchip Technology Inc.
14651 Dallas Parkway, Suite 816
Dallas, TX 75240-8809
Tel: 972-991-7177 Fax: 972-991-8588
Dayton
Microchip Technology Inc.
Two Prestige Place, Suite 150
Miamisburg, OH 45342
Tel: 937-291-1654 Fax: 937-291-9175
Microchip Technology
RM 406 Shanghai Golden Bridge Bldg.
2077 Yan’an Road West, Hongiao District
Shanghai, PRC 200335
Tel: 86-21-6275-5700
Fax: 86 21-6275-5060
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 714-263-1888 Fax: 714-263-1338
New York
Italy
Singapore
Microchip Technology Taiwan
Singapore Branch
200 Middle Road
#10-03 Prime Centre
Singapore 188980
Tel: 65-334-8870 Fax: 65-334-8850
Taiwan, R.O.C
Los Angeles
France
Microchip Technology Taiwan
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
Tel: 886 2-717-7175 Fax: 886-2-545-0139
JAPAN
Microchip Technology Intl. Inc.
Benex S-1 6F
3-18-20, Shin Yokohama
Kohoku-Ku, Yokohama
Kanagawa 222 Japan
Tel: 81-4-5471- 6166 Fax: 81-4-5471-6122
3/24/97
Microchip Technology Inc.
150 Motor Parkway, Suite 416
Hauppauge, NY 11788
Tel: 516-273-5305 Fax: 516-273-5335
San Jose
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950 Fax: 408-436-7955
Toronto
Microchip Technology Inc.
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905-405-6279 Fax: 905-405-6253
All rights reserved. 1997, Microchip Technology Incorporated, USA.
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement
of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and
name are registered trademarks of Microchip Technology Inc. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
DS30453A - page 220
1997 Microchip Technology Inc.