PTH03010 Series —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203A – MAY 2003 – REVISED MAY 2003 Features NOMINAL SIZE = • Up to 15-A Output Current • 3.3-V Input Voltage • Wide-Output Voltage Adjust (0.8 V to 2.5 V) • Efficiencies up to 95 % • 125 W/in³ Power Density • On/Off Inhibit • Output Voltage Sense • Pre-Bias Startup 1.37 in x 0.62 in (34,8 mm x 15,75 mm) • • • • • • • • Auto-Track™ Sequencing Margin Up/Down Controls Under-Voltage Lockout Output Over-Current Protection (Non-Latching, Auto-Reset) Surface Mountable Operating Temp: –40 to +85 °C DSP Compatible Output Voltages IPC Lead Free 2 Pin Configuration Auto-Track simplifies the task of supply voltage sequencing in a power system by enabling modules to track each other, or any external voltage, during power up and power down. Other operating features include an on/off inhibit, output voltage adjust (trim), and margin up/down controls. To ensure tight load regulation, an output voltage sense is also provided. A non-latching over-current trip serves as load fault protection. Target applications include complex multi-voltage, multi-processor systems that incorporate the industry’s high-speed DSPs, micro-processors and bus drivers. The PTH03010 series of non-isolated power modules are small in size but big on performance and flexibility. Their high output current, compact footprint, and industry-leading features offers system designers a versatile module for powering complex multi-processor digital systems. The series employs double-sided surface mount construction and provides highperformance step-down power conversion for up to 15 A of output current from a 3.3-V input bus voltage. The output voltage of the PTH03010W can be set to any value over the range, 0.8 V to 2.5 V, using a single resistor. This series includes Auto-Track™. Pin 1 2 3 4 5 6 7 8 9 10 Function GND Vin Inhibit * Vo Adjust Vo Sense Vout GND Track Margin Down * Margin Up * * Denotes negative logic: Open = Normal operation Ground = Function active Track Auto- ncing e Sequ Standard Application Track Margin Down Margin Up 1 10 9 8 7 PTH03010W (Top View) V IN 2 V OUT 6 3 4 5 Inhibit V o Sense + CIN 470 µF (Required) RSET 0.5 %, 0.1 W (Required) COUT 330 µF (Optional) GND L O A D + ADVANCE INFORMATION Description GND Rset = Resistor to set the desired output voltage (see spec. table for values) Cin = Required electrolytic 470 µF Cout = Recommended 330 µF electrolytic For technical support and more information, see inside back cover or visit www.ti.com PTH03010 Series —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203A – MAY 2003 – REVISED MAY 2003 Ordering Information Output Voltage (PTH03010Hxx) Package Options (PTH03010xHH) (1) Code W Code AH AS Voltage 0.8 V – 2.5 V (Adjust) Description Horiz. T/H SMD, Standard (3) Pkg Ref. (EUH) (EUJ) (2) Notes: (1) Add “T” to end of part number for tape and reel on SMD packages only. (2) Reference the applicable package reference drawing for the dimensions and PC board layout (3) “Standard” option specifies 63/37, Sn/Pb pin solder material. Pin Descriptions GND: This is the common ground connection for the Vin and Vout power connections. It is also the 0 VDC reference for the control inputs. Inhibit: The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a lowlevel ground signal to this input disables the module’s output and turns off the output voltage. When the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit pin is left open-circuit, the module will produce an output whenever a valid input source is applied. Vo Adjust: A 0.5 %, 0.1 W resistor must be connected between this pin and the GND pin to set the output voltage to the desired value. The set point range for the output voltage is from 0.8 V to 2.5 V. The resistor required for a given output voltage may be calculated from the following formula. If left open circuit, the module output will default to its lowest output voltage value. For further information on the adjustment and/or trimming of the output voltage, consult the related application note. Rset = 10 k · 0.8 V Vout – 0.8 V Track: This is an analog control input that allows the output voltage to follow another voltage during powerup and power-down sequences. The pin is active from 0 V up to the nominal set-point voltage. Within this range the module’s output will follow the voltage at the Track pin on a volt-for-volt basis. When the control voltage is raised above this range, the module regulates at its nominal output voltage. If unused, this input maybe left unconnected. For further information consult the related application note. Margin Down: When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input requires an open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can be accomodated with a series resistor. For further information, consult the related application note. Margin Up: When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open-collector (open-drain) interface. It is not TTL compatible. The percent change can be reduced with a series resistor. For further information, consult the related application note. – 2.49 k The specification table gives the preferred resistor values for a number of standard output voltages. For technical support and more information, see inside back cover or visit www.ti.com ADVANCE INFORMATION Vin: The positive input voltage power node to the module, which is referenced to common GND. Vout: The regulated positive power output with respect to the GND node. PTH03010 Series —3.3-V Input 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203A – MAY 2003 – REVISED MAY 2003 Environmental & Absolute Maximum Ratings Characteristics Symbols Track Input Voltage Operating Temperature Range Solder Reflow Temperature Storage Temperature Mechanical Shock Vtrack Ta Treflow Ts Mechanical Vibration Weight Flammability — — (Voltages are with respect to GND) Conditions Over Vin Range Surface temperature of module body or pins — Per Mil-STD-883D, Method 2002.3 1 msec, ½ Sine, mounted Mil-STD-883D, Method 2007.2 20-2000 Hz Min Typ –0.3 –40 — — Max Units –40 — — TBD — G’s — TBD — G’s — 5 — grams Vin + 0.3 85 215 (i) 125 V °C °C °C Meets UL 94V-O Notes: (i) During reflow of SMD package version do not elevate peak temperature of the module, pins or internal components above the stated maximum. For further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products.” ADVANCE INFORMATION Specifications (Unless otherwise stated, T a =25 °C, V in =3.3 V, Vout =2.5 V, C in =470 µF, C out =0 µF, and Io =Iomax) PTH03010W Typ Characteristics Symbols Conditions Min Max Units Output Current Io Vin Vo tol ∆Regtemp ∆Regline ∆Regload ∆Regtot 0 0 2.95 — — — — — — — — ±0.5 ±10 ±12 15 (1) 15 (1) 3.65 ±2 — — — A Input Voltage Range Set-Point Voltage Tolerance Temperature Variation Line Regulation Load Regulation Total Output Variation 60 °C, 200 LFM airflow 25 °C, natural convection Over Io range V %Vo %Vo mV mV — — ±3 %Vo Efficiency η — — — — — — — — 93 92 91 89 87 85 20 27.5 — — — — — — — — — — — — — 5 — TBD 70 100 ±5 – 8 (2) — — 2.95 2.8 — — — — –130 — TBD — Pin to GND Inhibit (pin 3) to GND, Track (pin 8) open Over Vin and Io ranges Vin –0.5 –0.2 — — 275 470 (4) 0 — — –130 10 300 — 330 (5) Open 0.8 — — 325 — 3,300 Per Bellcore TR-332 50 % stress, Ta =40 °C, ground benign 8.0 — — Vo Ripple (pk-pk) Over-Current Threshold Transient Response Vr Io trip Margin Up/Down Adjust Margin Input Current (pins 9 /10) Track Input Current (pin 8) Track Slew Rate Capability Under-Voltage Lockout ttr ∆Vtr Vo adj IIL margin IIL track dVtrack/dt UVLO Inhibit Control (pin3) Input High Voltage Input Low Voltage Input Low Current VIH VIL IIL inhibit Input Standby Current Switching Frequency External Input Capacitance External Output Capacitance Reliability Iin inh ƒs Cin Cout MTBF –40 °C <Ta < +85 °C Over Vin range Over Io range Includes set-point, line, load, –40 °C ≤ T a ≤ +85 °C Io =10 A RSET = 2.21 kΩ Vo = 2.5 V RSET = 4.12 kΩ Vo = 2.0 V RSET = 5.49 kΩ Vo = 1.8 V RSET = 8.87 kΩ Vo = 1.5 V RSET = 17.4 kΩ Vo = 1.2 V RSET = 36.5 kΩ Vo = 1.0 V 20 MHz bandwidth Reset, followed by auto-recovery 1 A/µs load step, 50 to 100 % Iomax, Cout =330 µF Recovery Time Vo over/undershoot Pin to GND Pin to GND Vtrack – Vo ≤ 50 mV and Vtrack < Vo(nom) Vin increasing Vin decreasing Referenced to GND % mVpp A (3) µSec mV % µA µA V/ms V (3) V µA mA kHz µF µF 106 Hrs Notes: (1) See SOA curves or consult factory for appropriate derating. (2) A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc. (3) This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small low-leakage (<100 nA) MOSFET is recommended for control. For further information, consult the related application note. (4) A 470-µF electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 700 mArms of ripple current. (5) An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response. For technical support and more information, see inside back cover or visit www.ti.com PTH03010 Series —3.3-V Input Typical Characteristics 15-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module SLTS203A – MAY 2003 – REVISED MAY 2003 Characteristic Data; Vin =3.3V Safe Operating Area; Vin =3.3 V (See Note A) Efficiency vs Load Current (See Note B) Output Voltage =2.5 V 100 90 Efficiency - % VOUT 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 1.0 V 80 70 60 Ambient Temperature (°C) 80 90 Airflow 70 400LFM 200LFM 100LFM Nat Conv 60 50 40 30 50 20 0 3 6 9 12 15 0 3 6 Iout - Amps 9 12 15 Iout (A) Output Ripple vs Load Current Output Voltage =1 V 50 90 1.8 V 1.5 V 2.0 V 1.2 V 1.0 V 2.5 V 30 20 10 Airflow 70 400LFM 200LFM 100LFM Nat Conv 60 50 40 30 0 20 0 3 6 9 12 15 0 Iout - Amps 3 6 9 12 15 Iout (A) Power Dissipation vs Load Current 4 Pd - Watts 3 2 1 0 0 3 6 9 12 15 Iout - Amps The products listed hereunder are prototype or pre-production devices which have not been fully qualified to Texas Instrument’s specifications. Product specifications are subject to change without notice. Texas Instruments makes no warranty, either expressed, implied, or statutory, including implied warranty of merchantability or fitness for a specific purpose, of these products. Note A: Characteristic data has been developed from actual products tested at 25°C. This data is considered typical data for the converter. Note B: SOA curves represent the conditions at which internal components are at or below the manufacturer’s maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in. × 4 in. double-sided PCB with 1 oz. copper. For technical support and more information, see inside back cover or visit www.ti.com ADVANCE INFORMATION Ripple - mV VOUT Ambient Temperature (°C) 80 40 Application Notes PTH03010 & PTH05010 Series only the AVX TPS, Sprague 593D/594/595 or Kemet T495/T510 series. These capacitors are recommended over many other tantalum types due to their higher rated surge, power dissipation, and ripple current capability. As a caution, the TAJ series by AVX is not recommended. This series has considerably higher ESR, reduced power dissipation, and lower ripple current capability. The TAJ series is less reliable than the AVX TPS series when determining power dissipation capability. Tantalum or Oscon® types are recommended for applications where ambient temperatures fall below 0 °C. Capacitor Recommendations for the PTH03010 & PTH05010 Series of Power Modules Input Capacitor The recommended input capacitance is determined by 700 mA rms minimum ripple current rating and 470 µF minimum capacitance. Ripple current and <100 mΩ equivalent series resistance (ESR) values are the major considerations, along with temperature, when designing with different types of capacitors. Tantalum capacitors have a recommended minimum voltage rating of twice 2× (the maximum DC voltage + AC ripple). This is necessary to insure reliability for input voltage bus applications. Ceramic Capacitors may be substituted for Electrolytic types with the minimum capacitor value for improved ripple reduction the input and output bus. Capacitor Table Table 1 identifies the characteristics of capacitors from a number of vendors with acceptable ESR and ripple current (rms) ratings. The number of capacitors required at both the input and output buses is identified for each capacitor type. Output Capacitors (Optional) The ESR of the capacitors is equal to or less than 150 mΩ. Electrolytic capacitors have marginal ripple performance at frequencies greater than 400 kHz but excellent low frequency transient response. Above the ripple frequency, ceramic capacitors are necessary to improve the transient response and reduce any high frequency noise components apparent during higher current excursions. Preferred lowESR type capacitor part numbers are identified in Table 2-1. This is not an extensive capacitor list. Capacitors from other vendors are available with comparable specifications. Those listed are for guidance. The RMS ripple current rating and ESR are the critical parameters necessary to insure both optimum regulator performance and long capacitor life. Tantalum Capacitors Tantalum type capacitors can be used for the output but Table 2-1: Input/Output Capacitors Capacitor Vendor/ Series Capacitor Characteristics Quantity Working Voltage Value (µF) (ESR) Equivalent Series Resistance Max. Ripple Current @105 °C (Irms) Physical Size (mm) Input Bus Output Bus FK (Surface Mt.) 10 V 16 V 25 V 35 V 560 470 470 470 0.090 Ω 0.090 Ω 0080 Ω 0.060 Ω 755 mA 755 mA 850 mA 1100 mA 10×12.5 10×12.5 10×10.2 12.5×13.5 1 1 1 1 1 1 1 1 EEUFC1A561 EEUFC1C471 EEVFK1E471P EEVFK1V471Q United Chemi-con LXZ Series FX PXA (Surface Mt.) 6.3 V 10 V 10 V 16 V 470 680 680 470 0.020 Ω 0.090 Ω 0.015 Ω 0.090 Ω 4130 mA 770 mA 4735 mA 760 mA 10×7.7 10×12.5 10×10.5 10×12.5 1 1 1 1 1 1 1 1 PXA6.3VC471MJ80TP LXZ10VB681M10X12LL 10FX680M LXZ16VB471M10X12LL Nichicon PM Series NA NX (Surface Mt.) 6.3 V 10 V 16 V 16 V 470 470 330 470 0.020 Ω 0.018 Ω 0.120÷2=0.060 Ω 0.090 Ω 4130 mA 4400 mA 745 mA 770 mA 10×8 10×10 '10×12.5 10×15 1 1 2 1 1 1 1 1 PNX0J471MCAR1GS PNA1A471M1 UPM1C331MPH6 UPM1C 471MPH6 Sanyo-Os-con: SP SVP (Surface Mt.) 10 V 10 V 470 560 0.015 Ω 0.013 Ω >4500 mA >5200 mA 10×10.5 11×12.7 1 1 1 1 10SP470M 10SVP560M AVX Tantalum TPS (Surface Mt.) 10 V 10 V 470 470 0.045 Ω 0.060 Ω 1723 mA 1826 mA 7.3L ×5.7W ×4.1H 1 1 1 1 TPSE477M010R0045 TPSV477M010R0060 Kemet Polymer Tantalum T520/T530 Series (Surface Mt.) 10 V 10 V 330 330 0.040 Ω 0.015 Ω 1800 mA >3800 mA 4.3W ×7.3L ×4.0H 2 2 1 1 T520X337M010AS T530X337M010AS Sprague Tantalum 595D Series (Surface Mt.) 10 V 470 0.100 Ω 1440 mA 7.2L ×6W ×4.1H 1 1 595D477X0010R2T Panasonic FC (Radial) For technical support and more information, see inside back cover or visit www.ti.com Vendor Part Number IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated