ATH18K12 Series —12-V Input 18-A, 12-V Input Non-Isolated Wide-Output Adjust Power Module REVISION 00 (30SEP2003) Features NOMINAL SIZE = 1.5 in x 0.87 in (38,1 mm x 22,1 mm) Description The ATH18K12 series of non-isolated power modules offers OEM designers a combination of high performance, small footprint, and industry leading features. As part of a new class of power modules, these products provide designers with the flexibility to power the most complex multi-processor digital systems using off-the-shelf catalog parts. The series employs double-sided surface mount construction and provides highperformance step-down power conversion for up to 18 A of output current from a 12-V input bus voltage. The output voltage of the ATH18K12 can be set to any value over the range, 1.2 V to 5.5 V, using a single resistor. • Up to 18 A Output Current • 12-V Input Voltage • Wide-Output Voltage Adjust (1.2 V to 5.5 V) • Efficiencies up to 95 % • 195 W/in³ Power Density • On/Off Inhibit • Output Voltage Sense • Margin Up/Down Controls • Under-Voltage Lockout • Auto-Track™ Sequencing • Output Over-Current Protection (Non-Latching, Auto-Reset) • Over-Temperature Protection • Surface Mountable • Operating Temp: –40 to +85 °C • DSP Compatible Output Voltages • IPC Lead Free 2 • Point-of-Load Alliance (POLA) Compatible Pin Configuration This series includes Auto-Track™. Auto-Track™ simplifies the task of supply voltage sequencing in a power system by enabling modules to track each other, or any external voltage, during power up and power down. Other operating features include an on/off inhibit, output voltage adjust (trim), and margin up/down controls. To ensure tight load regulation, an output voltage sense is also provided. A non-latching over-current trip and over-temperature shutdown provides load fault protection. Target applications include complex multi-voltage, multi-processor systems that incorporate the industry’s high-speed DSPs, micro-processors and bus drivers. Pin 1 2 3 4 5 6 7 8 9 10 Function GND Vin Inhibit * Vo Adjust Vo Sense Vout GND Track Margin Down * Margin Up * * Denotes negative logic: Open = Normal operation Ground = Function active ™ Track Auto- ncing e Sequ Standard Application Rset = Resistor to set the desired output voltage (see spec. table for values). Cin = Required electrolytic 560 µF Cout = Optional 330 µF electrolytic Track Margin Down Margin Up 10 9 8 1 7 ATH18K12-9S PTH12020W (Top View) VIN 2 VOUT 6 3 4 5 Vo Sense Inhibit RSET (Required) 0.1 W, 1 % + GND North America (USA): 1-888-41-ASTEC + CIN 560 µF (Required) COUT 330 µF (Optional) L O A D GND Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 ATH18K12 Series—12-V Input 18-A, 12-V Input Non-Isolated Wide-Output Adjust Power Module REVISION 00 (30SEP2003) Ordering Information Input Voltage 10.8V to 13.2V Options: “-J” “-SJ” “-S” - Output Voltage 1.2V1 to 5.5V Output Current 18A Model Number ATH18K12-9(S)(J) Through-hole Termination, Tray Packaging SMT Termination, Tray Packaging SMT Termination, T&R Packaging Notes: 1 Preset output voltage is 1.2V; externally adjustable to 5.5V Pin Descriptions Vin: The positive input voltage power node to the module, which is referenced to common GND. Vout: The regulated positive power output with respect to the GND node. GND: This is the common ground connection for the Vin and Vout power connections. It is also the 0 VDC reference for the control inputs. Inhibit: The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a lowlevel ground signal to this input disables the module’s o utput and turns o ff the o utput vo ltage. When the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit pin is left open-circuit, the module will produce an output whenever a valid input source is applied. Vo Adjust: A 0.1 W, 1 % tolerance (or better) resistor must be connected directly between this pin and pin 7 (GND) pin to set the output voltage to the desired value. The set point range for the output voltage is from 1.2 V to 5.5 V. The resistor required for a given output voltage may be calculated from the following formula. If left open circuit, the module output will default to its lowest output voltage value. For further information on output voltage adjustment consult the related application note. R set 0.8 V = 10 k · Vout – 1.2 V – 1.82 k The specification table gives the preferred resistor values for a number of standard output voltages. Vo Sense: The sense input allows the regulation circuit to compensate for voltage drop between the module and the load. For optimal voltage accuracy Vo Sense should be connected to Vout. It can also be left disconnected. Track: This is an analog control input that enables the output voltage to follow an external voltage. This pin becomes active typically 20 ms after the input voltage has been applied, and allows direct control of the output voltage from 0 V up to the nominal set-point voltage. Within this range the output will follow the voltage at the Track pin on a volt-for-volt basis. When the control voltage is raised above this range, the module regulates at its set-point voltage. The feature allows the output voltage to rise simultaneously with other modules powered from the same input bus. If unused, the input may b e le ft unc o nnec ted. Note: Due to the under-voltage lockout feature, the output of the module cannot follow its own input voltage during power up. For more information, consult the related application note. Margin Down: When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input requires an open-collector (open-drain) interface. It is not TTL compatible. A lower percent change can be accomodated with a series resistor. For further information, consult the related application note. Margin Up: When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open-collector (open-drain) interface. It is not TTL compatible. The percent change can be reduced with a series resistor. For further information, consult the related application note. ** Auto-Track is a trademark of Texas Instruments, Inc. North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 ATH18K12 Series—12-V Input 18-A, 12-V Input Non-Isolated Wide-Output Adjust Power Module REVISION 00 (30SEP2003) Environmental & Absolute Maximum Ratings Characteristics Symbols Track Input Voltage Operating Temperature Range Solder Reflow Temperature Storage Temperature Mechanical Shock V track Ta T reflow Ts Mechanical Vibration Weight Flammability — — (Voltages are with respect to GND) Conditions Over Vin Range Surface temperature of module body or pins — Per Mil-STD-883D, Method 2002.3 1 msec, ½ Sine, mounted Mil-STD-883D, Method 2007.2 20-2000 Hz Min Typ –0.2 –40 — — –40 — Max Units — 85 215 (i) 125 V °C °C °C 500 — G’s — 20 — G’s — 7 — grams V in Meets UL 94V-O Notes: (i) During reflow of SMD package version do not elevate peak temperature of the module, pins or internal components above the stated maximum. For further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products.” Specifications (Unless otherwise stated, Ta =25 °C, Vin =12 V, Vout =3.3 V, Cin =560 µF, Cout =0 µF, and Io =Iomax) PTH12020W Typ Characteristics Symbols Conditions Min Max Units Output Current Io V in 0 0 10.8 — — — — — — — — ±0.5 ±5 ±5 18 (1) 18 (1) 13.2 ±2 (2) — — — A Input Voltage Range Set-Point Voltage Tolerance Temperature Variation Line Regulation Load Regulation Total Output Variation 60 °C, 200 LFM airflow 25 °C, natural convection Over Io range — — ±3 Efficiency η — — — — — — — — — — 95.0 93.5 92.2 90.8 90.0 88.5 86.5 32 1 30 — — — — — — — — — — — — — — — 5 — 8.8 70 130 ±5 – 8 (3) — — 9.7 9.2 — — — — –0.13 — 10.4 — Pin to GND Inhibit (pin 3) to GND, Track (pin 8) open Over Vin and Io ranges Vin –0.5 –0.2 — — 260 560 (5) 0 — — –0.24 5 320 — 330 (6) Open (4) 0.5 — — 380 — 10,000 Per Bellcore TR-332 50 % stress, Ta =40 °C, ground benign 5.3 — — Vo tol ∆Regtemp ∆Regline ∆Regload ∆Regtot Vo Ripple (pk-pk) Vr Over-Current Threshold Transient Response Io trip Margin Up/Down Adjust Margin Input Current (pins 9 /10) Track Input Current (pin 8) Track Slew Rate Capability Under-Voltage Lockout ttr ∆Vtr ∆Vo margin IIL margin IIL track dVtrack/dt UVLO Inhibit Control (pin3) Input High Voltage Input Low Voltage Input Low Current VIH VIL IIL inhibit Input Standby Current Switching Frequency External Input Capacitance External Output Capacitance Reliability Iin inh ƒs Cin Cout MTBF –40 °C <Ta < +85 °C Over Vin range Over Io range Includes set-point, line, load, –40 °C ≤ Ta ≤ +85 °C Io =10 A RSET = 280 Ω Vo = 5.0 V RSET = 2.0 kΩ Vo = 3.3 V RSET = 4.32 kΩ Vo = 2.5 V RSET = 8.06 kΩ Vo = 2.0 V RSET = 11.5 kΩ Vo = 1.8 V RSET = 24.3 kΩ Vo = 1.5 V RSET = open cct.Vo = 1.2 V 20 MHz bandwidth Vo ≤2.5 V Vo >2.5 V Reset, followed by auto-recovery 1 A/µs load step, 50 to 100 % Iomax, Cout =330 µF Recovery Time Vo over/undershoot Pin to GND Pin to GND Vtrack – Vo ≤ 50 mV and Vtrack < Vo(nom) Vin increasing Vin decreasing Referenced to GND (2) V %Vo % Vo mV mV %Vo % mVpp % Vo A (4) µSec mV % µA mA V/ms V V mA mA kHz µF µF 106 Hrs Notes: (1) See SOA curves or consult factory for appropriate derating. (2) The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a tolerance of 1 %, with 200 ppm/°C or better temperature stability. (3) A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc. (4) This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small low-leakage (<100 nA) MOSFET is recommended for control. For further information, consult the related application note. (5) A 560 µF electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 800 mA rms of ripple current. (6) An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response. North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 ATH18K12 Series—12-V Input Typical Characteristics 18-A, 12-V Input Non-Isolated Wide-Output Adjust Power Module REVISION 00 (30SEP2003) Safe Operating Area; Vin =12 V (See Note B) Characteristic Data; Vin =12 V (See Note A) Efficiency vs Load Current Output Voltage =5 V 100 90 VOUT 5.0 V 3.3 V 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 80 70 60 80 Ambient Temperature (°C) Efficiency - % 90 Airflow 70 400LFM 200LFM 100LFM Nat conv 60 50 40 30 50 20 0 3 6 9 12 15 18 0 3 6 Iout - Amps Output Ripple vs Load Current 12 15 18 Output Voltage =2.5 V 100 90 5.0 V 3.3 V 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 60 40 20 80 Ambient Temperature (°C) VOUT 80 Ripple - mV 9 Iout (A) Airflow 70 400LFM 200LFM 100LFM Nat conv 60 50 40 30 0 20 0 3 6 9 12 15 18 0 3 6 Iout - Amps Power Dissipation vs Load Current 12 15 18 Output Voltage =1.8 V 6 90 5.0 V 3.3 V 2.5 V 2.0 V 1.8 V 1.5 V 1.2 V 4 3 2 1 80 Ambient Temperature (°C) VOUT 5 Pd - Watts 9 Iout (A) Airflow 70 400LFM 200LFM 100LFM Nat conv 60 50 40 30 0 20 0 5 10 15 0 3 Iout - Amps 6 9 12 15 18 Iout (A) Note A: Characteristic data has been developed from actual products tested at 25°C. This data is considered typical data for the Converter. Note B: SOA curves represent the conditions at which internal components are at or below the manufacturer’s maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in. × 4 in. double-sided PCB with 1 oz. copper. North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH18K12 Series Adjusting the Output Voltage of the ATH18K12 Wide-Output Adjust Power Module The Vo Adjust control (pin 4) sets the output voltage of the ATH18K12 product. The adjustment range is from 1.2 V to 5.5 V. To adjust the output voltage above 1.2 V a single external resistor, R set, must be connected directly between the Vo Adjust and GND pins 1. Table 1-1 gives the preferred value for the external resistor for a number of standard voltages, along with the actual output voltage that this resistance value provides. For other output voltages the value of the required resistor can either be calculated using the following formula, or simply selected from the range of values given in Table 1-2. Figure 1-1 shows the placement of the required resistor. Rset = 10 kΩ · 0.8 V Vout – 1.2 V – 1.82 kΩ Table 1-1; Preferred Values of R set for Standard Output Voltages Vout (Standard) Rset (Pref’d Value) 5V 3.3 V 2.5 V 2V 1.8 V 1.5 V 1.2 V 280 Ω 2 κΩ 4.32 κΩ 8.06 κΩ 11.5 κΩ 24.3 κΩ Open Vout (Actual) 5.009 V 3.294V 2.503 V 2.010V 1.801 V 1.506 V 1.200 V Figure 1-1; Vo Adjust Resistor Placement VO Sense [Note 3] 10 9 8 Table 1-2; Output Voltage Set-Point Resistor Values Va Req’d 1.200 1.225 1.250 1.275 1.300 1.325 1.350 1.375 1.400 1.425 1.450 1.475 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 Rset Open 318 κΩ 158 κΩ 105 κΩ 78.2 κΩ 62.2 κΩ 51.5 κΩ 43.9 κΩ 38.2 κΩ 33.7 κΩ 30.2 κΩ 27.3 κΩ 24.8 κΩ 21 κΩ 18.2 κΩ 16 κΩ 14.2 κΩ 12.7 κΩ 11.5 κΩ 10.5 κΩ 9.61 κΩ 8.85 κΩ 8.18 κΩ 7.59 κΩ 7.07 κΩ 6.6 κΩ 6.18 κΩ 5.8 κΩ 5.45 κΩ 5.14 κΩ 4.85 κΩ 4.85 κΩ 4.33 κΩ 4.11 κΩ 3.89 κΩ 3.7 κΩ 3.51 κΩ Va Req’d 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 Rset 3.34 κΩ 3.18 κΩ 3.03 κΩ 2.89 κΩ 2.75 κΩ 2.62 κΩ 2.5 κΩ 2.39 κΩ 2.28 κΩ 2.18 κΩ 2.08 κΩ 1.99 κΩ 1.9 κΩ 1.82 κΩ 1.74 κΩ 1.66 κΩ 1.58 κΩ 1.51 κΩ 1.38 κΩ 1.26 κΩ 1.14 κΩ 1.04 κΩ 939 Ω 847 Ω 761 Ω 680 Ω 604 Ω 533 Ω 466 Ω 402 Ω 342 Ω 285 Ω 231 Ω 180 Ω 131 Ω 85 Ω 41 Ω 5 VO Sense ATH18K12-9S PTH12020W GND 1 7 VOUT 6 VO Adj 4 RSET 0.1 W, 1 % COUT 330µF + GND VOUT GND North America (USA): 1-888-41-ASTEC Notes: 1. Use a 0.1 W resistor. The tolerance should be 1 %, with temperature stability of 100 ppm/°C (or better). Place the resistor as close to the regulator as possible. Connect the resistor directly between pins 4 and 7 using dedicated PCB traces. 2. Never connect capacitors from Vo Adjust to either GND or Vout. Any capacitance added to the Vo Adjust pin will affect the stability of the regulator. Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH18K12 Series ATH18K12: Capacitor Recommendations Tantalum Capacitors Tantalum type capacitors can be used for the output but only the AVX TPS, Sprague 593D/594/595 or Kemet T495/T510 series. These capacitors are recommended over many other tantalum types due to their higher rated surge, power dissipation, and ripple current capability. As a caution the TAJ series by AVX is not recommended. This series has considerably higher ESR, reduced power dissipation, and lower ripple current capability. The TAJ series is also less reliable than the AVX TPS series when determining power dissipation capability. Tantalum or Oscon® types are recommended for applications where ambient temperatures fall below 0°C. Input Capacitor The recommended input capacitor(s) is determined by the 560 µF minimum capacitance, and 800 mArms minimum ripple current rating. Ripple current and <100 mΩ equivalent series resistance (ESR) values are the major considerations, along with temperature, when designing with different types of capacitors. Tantalum capacitors have a recommended minimum voltage rating of 2 × (max. DC voltage + AC ripple). This is standard practice for tantalum capacitors to insure reliability. Tantalum capacitors are not recommended on the input bus. Ceramic Capacitors Ceramic capacitors can be substituted for electrolytic types on the output bus with the minimum capacitance for reducd ripple and improved transient response. Output Capacitors (Optional) The recommended ESR of the output capacitor is equal to or less than 150 mΩ. Electrolytic capacitors have marginal ripple performance at frequencies greater than 400 kHz but excellent low frequency transient response. Above the ripple frequency, ceramic capacitors are necessary to improve the transient response and reduce any high frequency noise components apparent during higher current excursions. Preferred low-ESR capacitor part numbers are identified in Table 2-1. Capacitor Table Table 2-1 identifies the characteristics of capacitors from a number of vendors with acceptable ESR and ripple current (rms) ratings. The number of capacitors required at both the input and output buses is identified for each capacitor type. This is not an extensive capacitor list. Capacitors from other vendors are available with comparable specifications. Those listed are for guidance. The RMS ripple current rating and ESR (at 100 kHz) are critical parameters necessary to insure both optimum regulator performance and long-term reliability. Table 2-1: Input/Output Capacitors Capacitor Vendor/ Series Capacitor Characteristics Working Voltage Value (µF) (ESR) Equivalent Series Resistance Quantity 105°C Maximum Ripple Current(Irms) Physical Size(mm) Input Bus Optional Output Bus Vendor Part Number FK (Surface Mt) 25 25 25 35 V V V V 330 560 1000 680 0.090 0.065 0.060 0.060 Ω Ω Ω Ω 755 mA 1205 mA 1100mA 1100 mA 10×12.5 12.5×15 12.5×13.5 12.5×13.5 2 1 1 1 1 1 1 1 EEUFC1E331 EEUFC1E561S EEVFK1E102Q EEVFK1V681Q United Chemi-Con FX LXZ Series 16 V 16 V 25V 330 330 680 0.018 Ω 0.090 Ω 0.068 Ω 4500 mA 760 mA 1050 mA 10×10.5 10×12.5 10×16 2 2 1 1 1 1 16FX330M LXZ25VB331M10X12LL LXZ16VB681M10X16LL Nichicon PM Series 25 V 25 V 35 V 560 680 560 0.060 Ω 0.055 Ω 0.048 Ω 1060 mA 1270 mA 1360 mA 12.5×15 16×15 16×15 1 1 1 1 1 1 UPM1E561MHH6 UPM1E681MHH6 UPM1V561MHH6 Os-con: SP SVP (Surface Mt) 16 V 16 V 270 330 0.018 Ω 0.016 Ω >3500 mA 4700 mA 10×10.5 11×12 2 2 1 1 16SP270M 16SVP330M AVX Tantalum TPS (Surface Mt) 10 V 10 V 330 330 0.1 Ω 0.06 Ω >2500 mA >3000 mA 7.3L ×5.7W ×4.1H N/R N/R (1) 1 1 TPSE337M010R0100 (Vo<5.1V) TPSV337M010R0060 (Vo<5.1V) Kemet Tantalum T520/T495 Series (Surface Mt) 10 V 10 V 330 220 0.040 Ω 0.07 Ω 1600 mA >2000 mA 4.3W ×7.3L ×4.0H N/R N/R (1) (1) 1 1 520X337M010AS (Vo<5.1V) T495X227M0100AS (Vo<5.1V) Sprague Tantalum 594D Series (Surface Mt) 10 V 330 0.045 Ω 2360 mA 7.2L ×6W ×4.1H N/R (1) 1 594D337X0010R2T (Vo<5.1V) Panasonic FC (Radial) (1) (1) N/R –Not recommended. The voltage rating does not meet the minimum operating limits. North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH Series of Wide-Output Adjust Power Modules (12-V Input) Features of the ATH Family of Non-Isolated Wide Output Adjust Power Modules This is a feature unique to the ATH family, and was specifically designed to simplify the task of sequencing the supply voltage in a power system. These and other features are described in the following sections. Point-of-Load Alliance The ATH family of non-isolated, wide-output adjust power modules from Texas Instruments are optimized for applications that require a flexible, high performance module that is small in size. These products are part of the “Point-of-Load Alliance” (POLA), which ensures compatible footprint, interoperability and true second sourcing for customer design flexibility. The POLA is a collaboration between Texas Instruments, Artesyn Technologies, and Astec Power to offer customers advanced non-isolated modules that provide the same functionality and form factor. Product series covered by the alliance includes the ATH06 (6 A), ATH10 (10 A), ATH12/15 (12/15 A), ATH18/22 (18/22 A), and the ATH26/30 (26/ 30 A). From the basic, “Just Plug it In” functionality of the 6-A modules, to the 30-A rated feature-rich ATH30 Series, these products were designed to be very flexible, yet simple to use. The features vary with each product. Table 3-1 provides a quick reference to the available features by product and input bus voltage. Power-Up Characteristics When configured per their standard application all the ATH products will produce a regulated output voltage following the application of a valid input source voltage. All the modules include soft-start circuitry. This slows the initial rate in which the output voltage can rise, thereby limiting the amount of in-rush current that can be drawn from the input source. The soft-start circuitry also introduces a short time delay (typically 5 ms-10 ms) into the power-up characteristic. This delay is from the point that a valid input source is recognized, to the initial rise of the output voltage. Figure 3-1 shows the power-up characteristic of the 10-A output product (ATH10K12), operating from a 12-V input bus and configured for a 3.3-V output. The waveforms were measured with a 5-A constant current load. The initial rise in input current when the input voltage first starts to rise is the charge current drawn by the input capacitors. Figure 3-1 PTHxx030 ATH26/30 6A 3.3 V / 5 V 10 A 12 V 10 8 AA 3.3 V / 5 V 15 A 12 V 12 A 3.3 V / 5 V 22 A 12 V 18 A 3.3 V / 5 V 30 A 12 V 26 A • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Thermal Shutdown • • • • • • • • • • • Pre-Bias Startup 6A 12 V • • • • • • • • • • • Output Sense PTHxx020 ATH18/22 5V • • • • • • • • • • • Margin Up/Down PTHxx010 ATH12/15 6A Auto-Track™ PTHxx060 ATH10 I OUT Over-Current PTHxx050 ATH06 Input Bus 3.3 V On/Off Inhibit Series Adjust (Trim) Table 3-1; Operating Features by Series and Input Bus Voltage Vo (2 V/Div) Iin (2 A/Div) HORIZ SCALE: 5 ms/Div • • • • For simple point-of-use applications, the ATH06 (6A) provides operating features such as an on/off inhibit, output voltage trim, pre-bias startup (3.3/5-V input only), and over-current protection. The ATH10 (10 A), and ATH12/ 15 (12/15 A) include an output voltage sense, and margin up/down controls. Then the higher output current, ATH18/22 (18/22A) and ATH26/30 (26/30A) products incorporate over-temperature shutdown protection. All of the products referenced in Table 3-1 include Auto-Track™. North America (USA): 1-888-41-ASTEC Vin (5 V/Div) Over-Current Protection For protection against load faults, all modules incorporate output over-current protection. Applying a load that exceeds the regulator’s over-current threshold will cause the regulated output to shut down. Following shutdown, a module will periodically attempt to recover by initiating a soft-start power-up. This is described as a “hiccup” mode of operation, whereby the module continues in a cycle of successive shutdown and power up until the load fault is removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is removed, the module automatically recovers and returns to normal operation. Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH Series of Wide-Output Adjust Power Modules (12-V Input) Output On/Off Inhibit Remote Sense For applications requiring output voltage on/off control, each series of the ATH family incorporates an output Inhibit control pin. The inhibit feature can be used wherever there is a requirement for the output voltage from the regulator to be turned off. The ATH10 (10A), ATH12/15 (12/15A), ATH18/22 (18/ 22A), and ATH26/30 (26/30A) products incorporate an output voltage sense pin, Vo Sense. The Vo Sense pin should be connected to Vout at the load circuit (see data sheet standard application). A remote sense improves the load regulation performance of the module by allowing it to compensate for any ‘IR’ voltage drop between itself and the load. An IR drop is caused by the high output current flowing through the small amount of pin and trace resistance. Use of the remote sense is optional. If not used, the Vo Sense pin can be left open-circuit. An internal low-value resistor (15-Ω or less) is connected between the Vo Sense and Vout. This ensures the output voltage remains in regulation. The power modules function normally when the Inhibit pin is left open-circuit, providing a regulated output whenever a valid source voltage is connected to Vin with respect to GND. Figure 3-2 shows the typical application of the inhibit function. Note the discrete transistor (Q1). The Inhibit input has its own internal pull-up to Vin potential (12 V). The input is not compatible with TTL logic devices. An open-collector (or open-drain) discrete transistor is recommended for control. Turning Q1 on applies a low voltage to the Inhibit control pin and disables the output of the module. If Q1 is then turned off, the module will execute a soft-start power-up sequence. A regulated output voltage is produced within 20 msec. Figure 3-3 shows the typical rise in both the output voltage and input current, following the turn-off of Q1. The turn off of Q1 corresponds to the rise in the waveform, Q1 Vds. The waveforms were measured with a 5-A constant current load. Figure 3-2 With the sense pin connected, the difference between the voltage measured directly between the Vout and GND pins, and that measured from V o Sense to GND, is the amount of IR drop being compensated by the regulator. This should be limited to a maximum of 0.3 V. Note: The remote sense feature is not designed to compensate for the forward drop of non-linear or frequency dependent components that may be placed in series with the converter output. Examples include OR-ing diodes, filter inductors, ferrite beads, and fuses. When these components are enclosed by the remote sense connection they are effectively placed inside the regulation control loop, which can adversely affect the stability of the regulator. Vo Sense Over-Temperature Protection (OTP) VIN 2 8 5 1 7 4 + Q1 BSS138 1 =Inhibit GND VOUT 6 PTH12060W ATH10K12 3 CIN 560 µF 9 RSET 2.0kΩ 1% 0.1 W COUT 330 µF + 10 L O A D GND Figure 3-3 Q1Vds (5 V/Div) Vo (2 V/Div) The ATH18/22 (18/22A) and ATH26/30 (26/30A) series of products have over-temperature protection. These products have an on-board temperature sensor that protects the module’s internal circuitry against excessively high temperatures. A rise in the internal temperature may be the result of a drop in airflow, or a high ambient temperature. If the internal temperature exceeds the OTP threshold, the module’s Inhibit control is automatically pulled low. This turns the output off. The output voltage will drop as the external output capacitors are discharged by the load circuit. The recovery is automatic, and begins with a soft-start power up. It occurs when the the sensed temperature decreases by about 10 °C below the trip point. Note: The over-temperature protection is a last resort mechanism to prevent thermal stress to the regulator. Operation at or close to the thermal shutdown temperature is not recommended and will reduce the long-term reliability of the module. Always operate the regulator within the specified Safe Operating Area (SOA) limits for the worst-case conditions of ambient temperature and airflow. Iin (2 A/Div) HORIZ SCALE: 10 ms/Div North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH Series of Wide-Output Adjust Power Modules (12-V Input) Auto-Track™Function The Auto-Track™ function is unique to the ATH family, and is available with the all “Point-of-Load Alliance” (POLA) products. Auto-Track™ was designed to simplify the amount of circuitry required to make the output voltage from each module power up and power down in sequence. The sequencing of two or more supply voltages during power up is a common requirement for complex mixed-signal applications, that use dual-voltage VLSI ICs such as DSPs, micro-processors, and ASICs. How Auto-Track™ Works Auto-Track™ works by forcing the module’s output voltage to follow a voltage presented at the Track control pin. This control range is limited to between 0 V and the module’s set-point voltage. Once the track-pin voltage is raised above the set-point voltage, the module’s output remains at its set-point 1. As an example, if the Track pin of a 2.5-V regulator is at 1 V, the regulated output will be 1 V. But if the voltage at the Track pin rises to 3 V, the regulated output will not go higher than 2.5 V. When under track control, the regulated output from the module follows the voltage at its Track pin on a voltfor-volt basis. By connecting the Track pin of a number of these modules together, the output voltages will follow a common signal during power-up and power-down. The control signal can be an externally generated master ramp waveform, or the output voltage from another power supply circuit 3. The Track control also incorporates an internal RC charge circuit. This operates off the module’s input voltage to produce a suitable rising waveform at power up. Typical Application The basic implementation of Auto-Track™ allows for simultaneous voltage sequencing of a number of AutoTrack™ compliant modules. Connecting the Track control pins of two or more modules forces the Track control of all modules to follow the same collective RC ramp waveform, and allows them to be controlled through a single transistor or switch; Q1 in Figure 3-4. To initiate a power-up sequence, it is recommended that the Track control be first pulled to ground potential. This should be done at or before input power is applied to the modules, and then held for at least 10 ms thereafter. This brief period gives the modules time to complete their internal soft-start initialization. Applying a logiclevel high signal to the circuit’s On/Off Control turns Q1 on and applies a ground signal to the Track pins. After completing their internal soft-start intialization, the output of all modules will remain at zero volts while Q1 is on. 10 ms after a valid input voltage has been applied to the modules, Q1 may be turned off. This allows the track control voltage to automatically rise toward to the modules' input voltage. During this period the output voltage of each module will rise in unison with other modules, to its respective set-point voltage. Figure 3-5 shows the output voltage waveforms from the circuit of Figure 3-4 after the On/Off Control is set from a high to a low-level voltage. The waveforms, Vo1 and Vo2 represent the output voltages from the two power modules, U1 (3.3 V) and U2 (2.0 V) respectively. Vo1 and Vo2 are shown rising together to produce the desired simultaneous power-up characteristic. The same circuit also provides a power-down sequence. Power down is the reverse of power up, and is accomplished by lowering the track control voltage back to zero volts. The important constraint is that a valid input voltage must be maintained until the power down is complete. It also requires that Q1 be turned off relatively slowly. This is so that the Track control voltage does not fall faster than Auto-Track's slew rate capability, which is 5 V/ms. The components R1 and C1 in Figure 3-4 limit the rate at which Q1 can pull down the Track control voltage. The values of 100 k-ohm and 0.047 µF correlate to a decay rate of about 0.6 V/ms. The power-down sequence is initiated with a low-to-high transition at the On/Off Control input to the circuit. Figure 3-6 shows the power-down waveforms. As the Track control voltage falls below the nominal set-point voltage of each power module, then its output voltage decays with all the other modules under Auto-Track™ control. Notes on Use of Auto-Track™ 1. The Track pin voltage must be allowed to rise above the module’s set-point voltage before the module can regulate at its adjusted set-point voltage. 2. The Auto-Track™ function will track almost any voltage ramp during power up, and is compatible with ramp speeds of up to 5 V/ms. 3. The absolute maximum voltage that may be applied to the Track pin is Vin. The open-circuit voltage is 0.56 × Vin, or 7.5 VDC maximum. 4. The module will not follow a voltage at its Track control input until it has completed its soft-start initialization. This takes about 10 ms from the time that the module has sensed that a valid voltage has been applied its input. During this period, it is recommended that the Track pin be held at ground potential. 5. Once its soft-start initialization is complete, the module is capable of both sinking and sourcing current when following the voltage at the Track pin. 6. The Auto-Track™ function can be disabled by connecting the Track pin to the input voltage (Vin) through a 1-kΩ resistor. When Auto-Track™ is disabled, the output voltage will rise faster following the application of input power. **Auto-Track is a trademark of Texas Instruments, Inc. North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH Series of Wide-Output Adjust Power Modules (12-V Input) Figure 3-4; Sequenced Power Up & Power Down Using Auto-Track U1 10 9 8 5 Track Inhibit + CIN ATH18K12 PTH12020W VIN VO Vo1 =3.3V 6 GND 3 7 1 COUT 4 R2 2.0kΩ + 2 +12V C1 0.047µF U2 9 8 5 Track 2 CIN 0V Figure 3-5; Simultaneous Power Up with Auto-Track Control + R1 100k 10 Q1 BSS138 ATH12K12 PTH12010W VIN Inhibit 3 VO Vo2 =2V 6 GND 1 7 4 R3 8k06 COUT + On/Off Control 1 = Power Down 0 = Power Up Figure 3-6; Simultaneous Power Down with Auto-Track Control Vo1 (1 V/Div) Vo1 (1V/Div) Vo2 (1 V/Div) Vo2 (1 V/Div) On/Off Control (5 V/Div) On/Off Control (5 V/Div) HORIZ SCALE: 5 ms/Div HORIZ SCALE: 10 ms/Div North America (USA): 1-888-41-ASTEC Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662 Application Notes ATH Series of Wide-Output Adjust Power Modules (12-V Input) Margin Up/Down Controls Notes: The ATH10 (10A), ATH12/15 (12/15A), ATH18/22 (18/ 22A), and ATH26/30 (26/30A) products incorporate Margin Up and Margin Down control inputs. These controls allow the output voltage to be momentarily adjusted 1, either up or down, by a nominal 5 %. This provides a convenient method for dynamically testing the operation of the load circuit over its supply margin or range. It can also be used to verify the function of supply voltage supervisors. The ±5 % change is applied to the adjusted output voltage, as set by the external resistor, Rset at the Vo Adjust pin. 1. The Margin Up* and Margin Dn* controls were not intended to be activated simultaneously. If they are their affects on the output voltage may not completely cancel, resulting in the possibility of a slightly higher error in the output voltage set point. The 5 % adjustment is made by pulling the appropriate margin control input directly to the GND terminal 2. A low-leakage open-drain device, such as an n-channel MOSFET or p-channel JFET is recommended for this purpose 3. Adjustments of less than 5 % can also be accommodated by adding series resistors to the control inputs (See Figure 3-4). The value of the resistor can be selected from Table 3-2, or calculated using the following formula. 2. The ground reference should be a direct connection to the module GND at pin 7 (pin 1 for the ATH06). This will produce a more accurate adjustment at the load circuit terminals. The transistors Q1 and Q2 should be located close to the regulator. 3. The Margin Up and Margin Dn control inputs are not compatible with devices that source voltage. This includes TTL logic. These are analog inputs and should only be controlled with a true open-drain device (preferably a discrete MOSFET transistor). The device selected should have low off-state leakage current. Each input sources 8 µA when grounded, and has an open-circuit voltage of 0.8 V. Up/Down Adjust Resistance Calculation To reduce the margin adjustment to something less than 5 %, series resistors are required (See RD and RU in Figure 3-7). For the same amount of adjustment, the resistor value calculated for RU and RD will be the same. The formulas is as follows. RU or RD = 499 ∆% – 99.8 Table 3-2; Margin Up/Down Resistor Values % Adjust 5 4 3 2 1 kΩ Where ∆% = The desired amount of margin adjust in percent. RU / RD 0.0 kΩ 24.9 kΩ 66.5 kΩ 150.0 kΩ 397.0 kΩ Figure 3-7; Margin Up/Down Application Schematic 10 9 8 1 7 ATH15T05 PTH05010W (Top View) VIN 0V 2 RD 4 MargUp 5 RU RSET 0.1 W, 1 % Cin MargDn +VOUT 6 3 + +Vo + Cout Q2 GND North America (USA): 1-888-41-ASTEC L O A D Q1 GND Europe (UK): 44(1384)842-211 Asia (HK): 852-2437-9662