BP5062-5 AC/DC converter AC100V C100V input, −5V/500mA 5V/500mA output Dimension(Unit : mm) Limits Unit Vi Io Vsurge Topr Tstg −190 500 2 −20 ∼ +80 −25 ∼ +105 V mApk kV °C °C 9.9MAX. 34.5MAX. Mark Side Symbol 21.5MAX. Parameter Input voltage Output current ESD endurance Operating temperature range Storage temperature range 1 4± 1.0 Absolute Maximum Ratings 3 5 7 8 10 12 0.25±0.05 0.5±0.1 1.3±0.2 P=5.08±0.2 3.3MAX 5.05MAX. 4.85MAX. 2.54×11=27.94 Electrical Characteristics Conditions DC (80∼120VAC) Vi=−141V, Io=500mA Vi=−141V ∗1 Vi=−113V∼ −170V, Io=500mA Vi=−141V, Io=0∼500mA Vi=−141V, Io=500mA ∗2 Vi=−141V, Io=500mA Unit V V mA V V Vp-p % ∗1 Maximum output current varies depending on ambient temperature ; please refer to derating curve. ∗2 Spike noise is not included in output ripple voltage. Application circuit Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 BP5062-5 Please note that pin No.12 side is input. 12 R1 D1 1SR139-400 4.7Ω1/4W Input AC100V 50Hz/60Hz ZNR − 220V + C1 22µF/200V 10 8 7 5 3 1 FUSE 2A C2 0.22µF L1 220µH Output −5V − + Function Output terminal Vo(−5V) Not used Coil connect Not used Coil connect Not used COMMON COMMON Not used N.C. Not used Input terminal Vi(−141VDC) C3 470µF/25V Be sure to use fuse for safety. Derating Curve Derating Curve 600 Output Current Io(mA) Max. −170 −5.3 500 0.2 0.3 0.3 − 500 400 300 Operation Range 200 100 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta(°C) Conversion Efficiency Conversion Efficiency (%) Typ. −141 −5.0 − 0.05 0.07 0.15 71 100 90 80 70 60 50 40 30 20 10 0 0 Conversion Efficiency (Ta=25°C, Vi=−141V) 100 200 300 400 Output Current Io(mA) 500 Load Regulation 6 Output Voltage Vo(V) Symbol Min. Parameter Input voltage range −113 Vi Output voltage −4.7 Vo Output current 0 Io Line regulation − Vr Load regulation − Vl Output ripple voltage − Vp Power conversion effciency 60 η 5 4 3 2 1 0 0 For acutual usage, Please kindly evaluate and confirm our part mounted in your product, Especially, Please make sure to confirm whether the load current exceed Max. rated current by using the current probe. Load Regulation (Ta=25°C, Vi=−141V) 100 200 300 400 500 600 700 800 Output Current Io(mA) Surface Temperature Rising FUSE: Fuse Please make sure to use quick acting fuse 2A C1: Capacitor for input voltage smoothing Capacitance : 22µF∼100µF Rated voltage : 200V or higher Ripple current is 0.22Arms above. Especially when the capacity is enlarged, rush current at powering up is increased. Please be careful in the evaluation. Capacitance : 0.1µF∼0.22µF Rated voltage : 200V or higher Film capacitor or ceramic capacitor. Reduce the noise terminal voltage. The constant value should be evaluated in the set. C2: For noise terminal voltage reduction C3: Capacitor for Output voltage smooting D1: Rectifier diode L1: Choke coil R1: For noise terminal voltage reduction ZNR: Varistor Temperature Rising ∆T(°C) External components setting 60 Surface Temperature Rising (Ta=25°C, Vi=−141V) 50 40 30 20 10 0 0 100 200 300 400 500 600 700 800 Output Current Io(mA) Capacitance : 220µF∼820µF Rated voltage : 16V or higher, ESR is 0.25Ω max. Ripple current is 0.4Arms above. Output noise voltage is infulenced.Please evaluate it in the actual set. In the absolute maximum ratings, the reverse peak voltage should be 400V or higher, the average rectifying current should be 1A or higher, and the peak surge current should be 40A or higher. (Full-wave rectifier can be used in out part.) The inductance should be 220µH,the rated direct current should be 1.3A above. Otherwise heating or abnormal oscilation occurs. When the input smoothing capacitor is enlarged,the rating of the rectifier diode should be higher. 4.7Ω∼10Ω 1/4W Reduce the noise terminal voltage.The constant value should be evaluated in set. Varistor must be used. It protects this part from lightning surge and static electricity. 1/2 Precautions on Use of ROHM Power Module Safety Precautions 1) The products are designed and produced for application in ordinary electronic equipment (AV equipment, OA equipment, telecommunication equipment, home appliances, amusement equipment etc.). If the products are to be used in devices requiring extremely high reliability (medical equipment, transport equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or operational error may endanger human life and sufficient fail-safe measures, please consult with the Company's sales staff in advance. If product malfunctions may result in serious damage, including that to human life, sufficient fail-safe measures must be taken, including the following: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits in the case of single-circuit failure 2) The products are designed for use in a standard environment and not in any special environments. Application of the products in a special environment can deteriorate product performance. Accordingly, verification and confirmation of product performance, prior to use, is recommended if used under the following conditions: [a] Use in various types of liquid, including water, oils, chemicals, and organic solvents [b] Use outdoors where the products are exposed to direct sunlight, or in dusty places [c] Use in places where the products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use in places where the products are exposed to static electricity or electromagnetic waves [e] Use in proximity to heat-producing components, plastic cords, or othe flammable items [f] Use involving sealing or coating the products with resin or other coating materials [g] Use involving unclean solder or use of water or water-soluble cleaning agents for cleaning after soldering [h] Use of the products in places subject to dew condensation 3) The products are not radiation resistant. 4) The Company is not responsible for any problems resulting from use of the products under conditions not recommended herein. 5) The Company should be notified of any product safety issues. Moreover, product safety issues should be periodically monitored by the customer. Precautions Regarding Application Example and External Circuits 1) If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the characteristics of the products and external components, including transient characteristics, as well as static characteristics. Please be informed that the Company has not conducted investigations on whether or not particular changes in the application examples or external circuits would result in the infringement of patent rights of a third party. 2) The application examples, their constants, and other types of information contained herein are applicable only when the products are used in accordance with standard methods. Therefore, if mass production is intended, sufficient consideration to external conditions must be made. Prohibitions Regarding Industrial Property 1) These Specifications contain information related to the Company’s industrial property. Any use of them other than pertaining to the usage of appropriate products is not permitted. Duplication of these Specifications and its disclosure to a third party without the Company’s permission is prohibited. 2) Information and data on products, including application examples, contained in these specifications are simply for reference; the Company does not guarantee any industrial property rights, intellectual property rights, or any other rights of a third party regarding this information or data. Accordingly, the Company does not bear any responsibility for: [a] infringement of the intellectual property rights of a third party [b] any problems incurred by the use of the products listed herein. 3) The Company prohibits the purchaser of its products to exercise or use the intellectual property rights, industrial property rights, or any other rights that either belong to or are controlled by the Company, other than the right to use, sell, or dispose of the products. 2/2