T-13/4 (5 mm) AlInGaP Lamps Technical Data Features • • • • High Intensity General Purpose Leads Popular 5 mm Diameter Available in Bulk, Tape and Reel, or Ammopack • 8° or 25° Viewing Angles • Choice of Colors: Amber or Red Applications • • • • Indoor/Outdoor Applications Small Store-front Signs Message Panels Road Construction Barrier Lights • Center High Mount Stop Lights HLMP-Cx08 Series HLMP-Cx25 Series HLMP-Cx27 Series HLMP-C610 • Spoiler, Car Decorative Lighting • Motorcycle/Bicycle Warning Lights Description The HLMP-Cx08, HLMP-Cx25, HLMP-Cx27, and HLMP-C610 series are 5 mm lamps specially designed for applications requiring very high on-axis intensity that is not achievable with a standard lamp. These devices are capable of producing light output over a wide range of drive currents. Built using AlInGaP technology, they are well suited for typical 5 mm TS-AlGaAs lamp applica- tions, and have significantly SUPERIOR RELIABILITY than most TS-AlGaAs lamps in wet/ hot environments. These lamps come with clear non-diffused lens and are optically designed to yield superior light output. Device Selection Part Number HLMP-C008-U00xx HLMP-C208-S00xx HLMP-C608-R00xx HLMP-C610-R00xx HLMP-C025-P00xx HLMP-C225-O00xx HLMP-C625-P00xx HLMP-C027-P00xx HLMP-C627-P00xx Typical Viewing Angle[1](degrees), Standoff 2Q1/2 No 8 8 8 Yes 8 No 25 25 25 Yes 25 25 Luminous Intensity, Iv (mcd) @ 20 mA Min. Typ. 2900.0 6000.0 2600.0 3000.0 1000.0 2000.0 1000.0 2000.0 500.0 1000.0 450.0 800.0 500.0 700.0 500.0 1000.0 500.0 700.0 Color Red Amber Red Red Red Amber Red Red Red Dominant Wavelength[2] 626 590 635 635 626 590 635 626 635 Notes: 1. u1/2 is the off-axis angle at which the luminous intensity is half of the axial luminous intensity. 2. The dominant wavelength, ld, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 2 Package Dimensions 6.10 (0.240) 5.46 (0.215) 1.07 (0.042) 0.56 (0.022) 1.00 (0.040) MAX. EPOXY MENISCUS 1.32 (0.052) 1.02 (0.040) 0.45 SQ. NOM. (0.018) 5.21 (0.205) 4.70 (0.105) 2.54 NOM. (0.100) CATHODE LEAD 9.14 (0.360) 8.36 (0.330) 1.27 MIN. (0.050) 13.50 (0.53) 13.30 (0.52) 25.40 MIN. (1.000) HLMP-Cx27 6.10 (0.240) 5.46 (0.215) 1.07 (0.042) 0.56 (0.022) 0.45 SQ. NOM. (0.018) 1.02 (0.004) MAX. TYP. 5.21 (0.205) 4.70 (0.105) 2.54 NOM. (0.100) CATHODE LEAD 9.14 (0.360) 8.36 (0.330) 1.27 MIN. (0.050) 25.40 MIN. (1.000) HLMP-Cx25 6.10 (0.240) 5.46 (0.215) 0.89 (0.035) 0.64 (0.023) 1.32 (0.052) 1.02 (0.040) 0.45 SQ. NOM. (0.018) 5.08 (0.200) 4.57 (0.100) 2.54 NOM. (0.100) CATHODE LEAD 9.19 (0.362) 8.43 (0.332) 1.27 MIN. (0.050) 13.55 (0.533) 13.35 (0.525) 25.40 MIN. (1.000) HLMP-C610 6.10 (0.240) 5.46 (0.215) 0.89 (0.035) 0.64 (0.023) 0.45 SQ. NOM. (0.018) 1.02 (0.004) MAX. TYP. 5.08 (0.200) 4.57 (0.100) 2.54 NOM. (0.100) 9.19 (0.362) 8.43 (0.332) CATHODE LEAD 1.27 MIN. (0.050) 25.40 MIN. (1.000) HLMP-Cx08 3 Part Numbering System HLMP - C x xx - x x x xx Mechanical Option 00: Bulk 02: Tape & Reel, Straight Leads DD: Ammo Pack Color Bin Options 0: Full Color Bin Distribution Maximum Iv Bin Options 0: Open (no max. limit) Minimum Iv Bin Options Please refer to the Iv Bin Table Viewing Angle & Standoff Option 08: 8 degrees, without standoff 10: 8 degrees, with standoff 25: 25 degrees, without standoff 27: 25 degrees, with standoff Color Options 0: AlInGaP Red 626 nm 2: AlInGaP Amber 590 nm 6: AlInGaP Red 635 nm Absolute Maximum Ratings at TA=25°C Parameter Peak Forward Current Average Forward Current[1] DC Current[2] Reverse Voltage (IR = 100 µA) LED Junction Temperature Operating Temperature Storage Temperature Lead Soldering Temperature [1.59 mm (0.060 in.) below seating plane] Absolute Maximum 70 30 50 5 110 -40 to +100 -40 to +120 260°C for 5 seconds Units mA mA mA V °C °C Notes: 1. See Figure 2 to establish pulsed operating conditions. 2. Derate linearly from 50°C at 0.5 mA/°C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wirebond. It is not recommended that this device be operated at peak currents above the Absolute Maximum Peak Forward Current. 4 Optical/Electrical Characteristics at TA=25°C Symbol 2θ1/2 Dλ1/2 τs C Parameter Device Included Angle Between Half HLMP-C008 Luminous Intensity Points[1] HLMP-C208 HLMP-C608 HLMP-C025 HLMP-C225 HLMP-C625 HLMP-C610 HLMP-C027 HLMP-C627 Dominant Wavelength[2] HLMP-C008 HLMP-C208 HLMP-C608 HLMP-C025 HLMP-C225 HLMP-C625 HLMP-C610 HLMP-C027 HLMP-C627 Peak Wavelength HLMP-C008 HLMP-C208 HLMP-C608 HLMP-C025 HLMP-C225 HLMP-C625 HLMP-C610 HLMP-C027 HLMP-C627 Spectral Line Halfwidth Speed of Response Capacitance RθJ-PIN Thermal Resistance λd λPEAK VF Forward Voltage VR Reverse Breakdown Voltage Min. Typ.[3] 8 8 8 25 25 25 8 25 25 626 590 635 626 590 635 635 626 635 635 594 650 635 594 650 650 635 650 17 20 40 Max. 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 5.0 Test Conditions I F = 20 mA See Note 1 nm See Note 2 nm Measurement at Peak nm ns pF V VF = 0; f = 1 MHz Junction to Cathode Lead IF = 20 mA V IR = 100 µA °C/W 260 HLMP-C008 HLMP-C208 HLMP-C608 HLMP-C025 HLMP-C225 HLMP-C625 HLMP-C610 HLMP-C027 HLMP-C627 Units Deg. 2.4 2.6 2.6 2.4 2.6 2.6 2.6 2.4 2.6 Notes: 1. θ 1/ 2 is the off-axis angle at which the luminous intensity is half of the axial luminous intensity. 2. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Typical specification for reference only. Do not exceed absolute maximum ratings. 5 RELATIVE INTENSITY 1.0 C008 C025 C027 C208 C225 C608 C625 C627 C610 0.5 0 550 600 650 700 WAVELENGTH – nm 60 5 50 CURRENT – mA 4 3 100 300 Hz z Hz z 1 KH 3 KH Hz Hz 10 K KHz 2 30 K IPEAK – MAX. IDC – MAX. 6 100 RATIO OF MAXIMUM TOLERABLE PEAK CURRENT TO MAXIMUM TOLERABLE DC CURRENT Figure 1. Relative Intensity vs. Wavelength. RED AMBER 30 20 10 1 1.0 10 100 1000 0 1.0 10,000 3.0 2.5 Figure 3. Forward Current vs. Forward Voltage. 3.0 FORWARD CURRENT (mA) 60 2.5 2.0 1.5 1.0 0.5 0 2.0 1.5 VF – FORWARD VOLTAGE – V tp – PULSE DURATION – µs Figure 2. Maximum Tolerable Peak Current vs. Pulse Duration. RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 40 0 20 40 IF – DC FORWARD CURRENT – mA Figure 4. Relative Luminous Intensity vs. Forward Current. 60 40 RθJ-A = 780°C/W 20 0 0 20 40 60 80 100 AMBIENT TEMPERATURE (°C) Figure 5. Maximum Forward DC Current vs. Ambient Temperature. 120 1.0 RELATIVE INTENSITY 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -25 -20 -15 -10 -5 0 5 10 15 20 25 ANGULAR DISPLACEMENT – DEGREES Figure 6. Relative Luminous Intensity vs. Angular Displacement for HLMP-Cx08 and HLMP-Cx10. 1.0 RELATIVE INTENSITY 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 ANGULAR DISPLACEMENT – DEGREES Figure 7. Relative Luminous Intensity vs. Angular Displacement for HLMP-Cx25 and HLMP-Cx27. Soldering/Cleaning Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For information on soldering LEDs, please refer to Application Note 1027. Intensity Bin Limits Color Intensity Range (mcd) Min. Max. 540.0 850.0 850.0 1200.0 1200.0 1700.0 1700.0 2400.0 2400.0 3400.0 3400.0 4900.0 4900.0 7100.0 7100.0 10200.0 10200.0 14800.0 14800.0 21400.0 21400.0 30900.0 510.0 800.0 800.0 1250.0 1250.0 1800.0 1800.0 2900.0 2900.0 4700.0 4700.0 7200.0 7200.0 11700.0 11700.0 18000.0 18000.0 27000.0 Bin P Q R S T U V W X Y Z O P Q R S T U V W Red Yellow Maximum tolerance for each bin limit is ± 18%. Color Categories Color Category # 3 2 4 6 7 Amber Lambda (nm) Min. Max. 584.5 587.0 587.0 589.5 589.5 592.0 592.0 594.5 594.5 597.0 Tolerance for each bin limit is ± 0.5 nm. Mechanical Option Matrix Mechanical Option Code Definition 00 Bulk Packaging, minimum increment 500 pcs/bag 02 Tape & Reel, straight leads, minimum increment 1300 pcs/bag DD Ammo Pack, straight leads with minimum increment 2K/pack Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information. www.semiconductor.agilent.com Data subject to change. Copyright © 2001 Agilent Technologies, Inc. June 25, 2001 Obsoletes 5968-7196E (11/99) 5988-2231EN