ETC LM393/D

LM393, LM293, LM2903,
LM2903V
Low Offset Voltage
Dual Comparators
The LM393 series are dual independent precision voltage
comparators capable of single or split supply operation. These devices
are designed to permit a common mode range–to–ground level with
single supply operation. Input offset voltage specifications as low as
2.0 mV make this device an excellent selection for many applications
in consumer, automotive, and industrial electronics.
• Wide Single–Supply Range: 2.0 Vdc to 36 Vdc
• Split–Supply Range: ±1.0 Vdc to ±18 Vdc
• Very Low Current Drain Independent of Supply Voltage: 0.4 mA
• Low Input Bias Current: 25 nA
• Low Input Offset Current: 5.0 nA
• Low Input Offset Voltage: 5.0 mV (max) LM293/393
• Input Common Mode Range to Ground Level
• Differential Input Voltage Range Equal to Power Supply Voltage
• Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS
Logic Levels
• ESD Clamps on the Inputs Increase the Ruggedness of the Device
without Affecting Performance
http://onsemi.com
PDIP–8
N SUFFIX
CASE 626
8
1
SO–8
D SUFFIX
CASE 751
8
1
PIN CONNECTIONS
Output A
1
8
2
7
4
–
+ 5
–
+
3
Inputs A
Gnd
6
VCC
Output B
Inputs B
(Top View)
ORDERING INFORMATION
Device
VCC
+ Input
- Input
Output
R2
2.1 k
Q3
Q4
R4
Q5
Q6
Q14
2.0 k
F1
Q1
Q8
Q9
Q2
R1
4.6 k
Shipping
LM293D
SO–8
98 Units/Rail
LM293DR2
SO–8
2500 Tape & Reel
LM393D
SO–8
98 Units/Rail
LM393DR2
SO–8
2500 Tape & Reel
LM393N
PDIP–8
50 Units/Rail
LM2903D
SO–8
98 Units/Rail
LM2903DR2
SO–8
2500 Tape & Reel
PDIP–8
50 Units/Rail
LM2903VD
SO–8
98 Units/Rail
LM2903VDR2
SO–8
2500 Tape & Reel
PDIP–8
50 Units/Rail
LM2903N
Q10
Q16
Q12
Q11
Package
Q15
LM2903VN
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 6 of this data sheet.
Figure 1. Representative Schematic Diagram
(Diagram shown is for 1 comparator)
 Semiconductor Components Industries, LLC, 2001
June, 2001 – Rev. 4
1
Publication Order Number:
LM393/D
LM393, LM293, LM2903, LM2903V
MAXIMUM RATINGS
Symbol
Value
Unit
Power Supply Voltage
Rating
VCC
+36 or ±18
Vdc
Input Differential Voltage Range
VIDR
36
Vdc
Input Common Mode Voltage Range
VICR
–0.3 to +36
Vdc
Output Short Circuit–to–Ground
Output Sink Current (Note 1.)
ISC
ISink
Continuous
20
mA
Power Dissipation @ TA = 25°C
Derate above 25°C
PD
1/RθJA
570
5.7
mW
mW/°C
Operating Ambient Temperature Range
LM293
LM393
LM2903
LM2903V
°C
TA
–25 to +85
0 to +70
–40 to +105
–40 to +125
Maximum Operating Junction Temperature
LM393, 2903, LM2903V
LM293
°C
TJ(max)
150
150
Storage Temperature Range
Tstg
–65 to +150
°C
1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause
excessive heating and eventual destruction.
http://onsemi.com
2
LM393, LM293, LM2903, LM2903V
ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow ≤ TA ≤ Thigh, unless otherwise noted.)
LM293, LM393
Characteristic
Symbol
Input Offset Voltage (Note 3.)
TA = 25°C
Tlow ≤ TA ≤ Thigh
VIO
Input Offset Current
TA = 25°C
Tlow ≤ TA ≤ Thigh
IIO
Input Bias Current (Note 4.)
TA = 25°C
Tlow ≤ TA ≤ Thigh
IIB
LM2903, LM2903V
Min
Typ
Max
Min
Typ
Max
–
–
±1.0
–
±5.0
9.0
–
–
±2.0
9.0
±7.0
15
–
–
±5.0
–
±50
±150
–
–
±5.0
±50
±50
±200
–
–
25
–
250
400
–
–
25
200
250
500
0
0
–
–
VCC –1.5
VCC –2.0
0
0
–
–
VCC –1.5
VCC –2.0
Unit
mV
nA
nA
Input Common Mode Voltage Range (Note 4.)
TA = 25°C
Tlow ≤ TA ≤ Thigh
VICR
Voltage Gain
RL ≥ 15 kΩ, VCC = 15 Vdc, TA = 25°C
AVOL
50
200
–
25
200
–
V/mV
Large Signal Response Time
Vin = TTL Logic Swing, Vref = 1.4 Vdc
VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
–
–
300
–
–
300
–
ns
Response Time (Note 6.)
VRL = 5.0 Vdc, RL = 5.1 kΩ, TA = 25°C
tTLH
–
1.3
–
–
1.5
–
µs
Input Differential Voltage (Note 7.)
All Vin ≥ Gnd or V– Supply (if used)
VID
–
–
VCC
–
–
VCC
V
Output Sink Current
Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, VO ≤ 1.5 Vdc TA = 25°C
ISink
6.0
16
–
6.0
16
–
mA
Output Saturation Voltage
Vin ≥ 1.0 Vdc, Vin+ = 0, ISink ≤ 4.0 mA, TA = 25°C
Tlow ≤ TA ≤ Thigh
VOL
–
–
150
–
400
700
–
–
–
200
400
700
Output Leakage Current
Vin– = 0 V, Vin+ ≥ 1.0 Vdc, VO = 5.0 Vdc, TA = 25°C
Vin– = 0 V, Vin+ ≥ 1.0 Vdc, VO = 30 Vdc,
Tlow ≤ TA ≤ Thigh
IOL
–
0.1
–
–
0.1
–
–
–
1000
–
–
1000
–
–
0.4
–
1.0
2.5
–
–
0.4
–
1.0
2.5
Supply Current
RL = ∞ Both Comparators, TA = 25°C
RL = ∞ Both Comparators, VCC = 30 V
LM293 Tlow = –25°C, Thigh = +85°C
LM393 Tlow = 0°C, Thigh = +70°C
LM2903 Tlow = –40°C, Thigh = +105°C
LM2903V Tlow = –40°C, Thigh = +125°C
V
mV
nA
ICC
mA
2. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause
excessive heating and eventual destruction.
3. At output switch point, VO1.4 Vdc, RS = 0 Ω with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to
VCC = –1.5 V).
4. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state,
therefore, no loading changes will exist on the input lines.
5. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of
common mode range is VCC –1.5 V.
6. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are
obtainable.
7. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common
mode range. The low input state must not be less than –0.3 V of ground or minus supply.
http://onsemi.com
3
LM393, LM293, LM2903, LM2903V
LM2903
80
80
70
70
60
IIB , INPUT BIAS CURRENT (nA)
IIB , INPUT BIAS CURRENT (nA)
LM293/393
TA = -55° C
50
TA = 0° C
40
TA = +25° C
30
20
TA = +70° C
TA = +125°C
10
0
0
5.0
10
15
20
25
30
VCC, SUPPLY VOLTAGE (Vdc)
35
TA = -40° C
60
50
TA = 0° C
40
TA = +25° C
30
TA = +85° C
20
10
0
40
0
10
TA = +125°C
TA = +25° C
TA = -55° C
0.01
0.001
0.01
0.1
1.0
10
35
1.0
TA = +85° C
0.1
TA = +25° C
0.01
TA = 0° C
TA = -40° C
0.001
0.01
100
0.1
1.0
10
100
Figure 4. Output Saturation Voltage
versus Output Sink Current
Figure 5. Output Saturation Voltage
versus Output Sink Current
TA = -55° C
TA = 0° C
TA = +25° C
0.6
TA = +70° C
0.4
TA = +125°C
0.2
RL = 5.0
10
15
20
25
30
40
Out of
Saturation
ISink, OUTPUT SINK CURRENT (mA)
0.8
0
30
ISink, OUTPUT SINK CURRENT (mA)
1.0
ICC , SUPPLY CURRENT (mA)
VOL , SATURATION VOLTAGE (Vdc)
0.1
10
Out of
Saturation
1.0
10
15
20
25
VCC, SUPPLY VOLTAGE (Vdc)
Figure 3. Input Bias Current versus
Power Supply Voltage
ICC , SUPPLY CURRENT (mA)
VOL , SATURATION VOLTAGE (Vdc)
Figure 2. Input Bias Current versus
Power Supply Voltage
5.0
TA = -40° C
1.2
TA = 0° C
1.0
TA = +25° C
0.8
TA = +85° C
0.6
RL = 0.4
35
0
40
VCC, SUPPLY VOLTAGE (Vdc)
5.0
10
15
20
25
30
35
VCC, SUPPLY VOLTAGE (Vdc)
Figure 6. Power Supply Current versus
Power Supply Voltage
Figure 7. Power Supply Current versus
Power Supply Voltage
http://onsemi.com
4
40
LM393, LM293, LM2903, LM2903V
APPLICATIONS INFORMATION
The addition of positive feedback (<10 mV) is also
recommended. It is good design practice to ground all
unused pins.
Differential input voltages may be larger than supply
voltage without damaging the comparator’s inputs. Voltages
more negative than –0.3 V should not be used.
These dual comparators feature high gain, wide
bandwidth characteristics. This gives the device oscillation
tendencies if the outputs are capacitively coupled to the
inputs via stray capacitance. This oscillation manifests itself
during output transitions (VOL to VOH). To alleviate this
situation, input resistors <10 kΩ should be used.
+15 V
Vin
R1
8.2 k
R4
220 k
R1
D1
6.8 k
R2
R5
220 k
LM393
+VCC
15 k
R3
Θ
10 k
10 M
LM393
Vin
VCC
D1 prevents input from going negative by more than 0.6 V.
VO
-VEE
R1 + R2 = R3
R5
for small error in zero crossing.
R3 ≤
10
Figure 9. Zero Crossing Detector
(Split Supply)
51 k
VCC
R
LM393
VC
+
RL
10 k
0.001 µF LM393
51 k
t
VCC
-
∆Θ
Vin(min) 0.4 V peak for 1% phase distortion (∆Θ).
VCC
1.0 MΩ
Θ
- VEE
Figure 8. Zero Crossing Detector
(Single Supply)
VCC
Vin(min)
Vin
10 k
RL
C
LM393
+
VO
VO
+ Vref
+
51 k
``ON'' for t tO + ∆t
where:
Vref
)
∆t = RC n (
VCC
VCC
VO
0
Vin
VO
0
VC
0
tO
t
VCC
RL
-
RS = R1 | | R2
Vth1 = Vref +
LM393
+
Vref
Vref
Figure 11. Time Delay Generator
Figure 10. Free–Running Square–Wave Oscillator
RS
Vref
0
Vth2 = Vref -
R1
R2
Figure 12. Comparator with Hysteresis
http://onsemi.com
5
(VCC -Vref) R1
R1 + R2 + RL
(Vref -VO Low) R1
R1 + R2
t
LM393, LM293, LM2903, LM2903V
MARKING DIAGRAMS
PDIP–8
N SUFFIX
CASE 626
8
8
LM393N
AWL
YYWW
LM2903N
AWL
YYWW
1
1
SO–8
D SUFFIX
CASE 751
8
8
LMx93
ALYW
1
8
2903
ALYW
1
x
A
WL, L
YY, Y
WW, W
2903V
ALYW
1
= 2 or 3
= Assembly Location
= Wafer Lot
= Year
= Work Week
http://onsemi.com
6
LM393, LM293, LM2903, LM2903V
PACKAGE DIMENSIONS
PDIP–8
N SUFFIX
CASE 626–05
ISSUE K
8
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5
–B–
1
4
DIM
A
B
C
D
F
G
H
J
K
L
M
N
F
–A–
NOTE 2
L
C
J
–T–
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
--10
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
--10
0.030
0.040
N
SEATING
PLANE
D
M
K
G
H
0.13 (0.005)
T A
M
M
B
M
SO–8
D SUFFIX
CASE 751–07
ISSUE W
–X–
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
A
8
5
0.25 (0.010)
S
B
1
M
Y
M
4
K
–Y–
G
C
N
X 45 SEATING
PLANE
–Z–
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
S
http://onsemi.com
7
J
DIM
A
B
C
D
G
H
J
K
M
N
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0
8
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0
8
0.010
0.020
0.228
0.244
LM393, LM293, LM2903, LM2903V
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
8
LM393/D