ETC LM833_NATIONAL

LM833
Dual Audio Operational Amplifier
General Description
Features
The LM833 is a dual general purpose operational amplifier
designed with particular emphasis on performance in audio
systems.
n Wide dynamic range:
This dual amplifier IC utilizes new circuit and processing
techniques to deliver low noise, high speed and wide bandwidth without increasing external components or decreasing
stability. The LM833 is internally compensated for all closed
loop gains and is therefore optimized for all preamp and high
level stages in PCM and HiFi systems.
The LM833 is pin-for-pin compatible with industry standard
dual operational amplifiers.
Schematic Diagram
140dB
n Low input noise
voltage:
n High slew rate:
n High gain bandwidth:
4.5nV/√Hz
7 V/µs (typ); 5V/µs (min)
15MHz (typ); 10MHz (min)
n Wide power bandwidth:
120KHz
n Low distortion:
0.002%
n Low offset voltage:
0.3mV
n Large phase margin:
n Available in 8 pin MSOP package
60˚
(1/2 LM833)
DS005218-1
Connection Diagram
DS005218-2
Order Number LM833M, LM833N or LM833MM
See NS Package Number
M08A, N08E or MUA08A
© 1999 National Semiconductor Corporation
DS005218
www.national.com
LM833 Dual Audio Operational Amplifier
August 1997
Absolute Maximum Ratings (Note 1)
Soldering Information
Dual-In-Line Package
Soldering (10 seconds)
260˚C
Small Outline Package
(SOIC and MSOP)
Vapor Phase (60 seconds)
215˚C
Infrared (15 seconds)
220˚C
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
ESD tolerance (Note 5)
1600V
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage VCC–VEE
Differential Input Voltage (Note 3) VI
Input Voltage Range (Note 3) VIC
Power Dissipation (Note 4) PD
Operating Temperature Range TOPR
Storage Temperature Range TSTG
36V
± 30V
± 15V
500 mW
−40 z 85˚C
−60 z 150˚C
DC Electrical Characteristics
(Notes 1, 2)
(TA = 25˚C, VS = ± 15V)
Symbol
Parameter
Typ
Max
Units
0.3
5
mV
Input Offset Current
10
200
nA
IB
Input Bias Current
500
1000
AV
Voltage Gain
VOM
Output Voltage Swing
VCM
Input Common-Mode Range
CMRR
Common-Mode Rejection Ratio
PSRR
Power Supply Rejection Ratio
IQ
Supply Current
VOS
Input Offset Voltage
IOS
Conditions
RS = 10Ω
Min
RL = 2 kΩ, VO = ± 10V
RL = 10 kΩ
RL = 2 kΩ
VIN = ± 12V
VS = 15z5V, −15z−5V
VO = 0V, Both Amps
nA
90
110
dB
± 12
± 10
± 12
± 13.5
± 13.4
± 14.0
V
80
100
dB
80
100
V
V
dB
5
8
mA
AC Electrical Characteristics
(TA = 25˚C, VS = ± 15V, RL = 2 kΩ)
Symbol
Parameter
SR
Slew Rate
GBW
Gain Bandwidth Product
Conditions
RL = 2 kΩ
f = 100 kHz
Min
Typ
5
7
Max
Units
V/µs
10
15
MHz
Design Electrical Characteristics
(TA = 25˚C, VS = ± 15V)
The following parameters are not tested or guaranteed.
Symbol
∆VOS/∆T
Parameter
Conditions
Average Temperature Coefficient
Typ
Units
2
µV/˚C
0.002
%
of Input Offset Voltage
THD
Distortion
en
Input Referred Noise Voltage
RL = 2 kΩ, f = 20z20 kHz
VOUT = 3 Vrms, AV = 1
RS = 100Ω, f = 1 kHz
in
Input Referred Noise Current
f = 1 kHz
0.7
120
kHz
9
MHz
60
deg
−120
dB
PBW
Power Bandwidth
VO = 27 Vpp, RL = 2 kΩ, THD ≤ 1%
fU
Unity Gain Frequency
Open Loop
φM
Phase Margin
Open Loop
f = 20z20 kHz
Input Referred Cross Talk
www.national.com
2
4.5
Design Electrical Characteristics
(Continued)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is
given, however, the typical value is a good indication of device performance.
Note 2: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 3: If supply voltage is less than ± 15V, it is equal to supply voltage.
Note 4: This is the permissible value at TA ≤ 85˚C.
Note 5: Human body model, 1.5 kΩ in series with 100 pF.
Typical Performance Characteristics
Maximum Power
Dissipation
vs Ambient Temperature
Input Bias Current vs
Ambient Temperature
DS005218-4
Supply Current vs
Supply Voltage
Input Bias Current vs
Supply Voltage
DS005218-5
DC Voltage Gain
vs Ambient Temperature
DC Voltage Gain
vs Supply Voltage
DS005218-8
DS005218-7
Voltage Gain & Phase
vs Frequency
DS005218-6
Gain Bandwidth Product
vs Ambient Temperature
DS005218-10
Gain Bandwidth
vs Supply Voltage
DS005218-11
3
DS005218-9
DS005218-12
www.national.com
Typical Performance Characteristics
Slew Rate vs
Ambient Temperature
(Continued)
Slew Rate vs
Supply Voltage
Power Bandwidth
DS005218-13
CMR vs Frequency
Distortion vs Frequency
DS005218-19
PSRR vs Frequency
DS005218-20
Maximum
Output Voltage vs
Supply Voltage
DS005218-18
Maximum
Output Voltage vs
Ambient Temperature
DS005218-16
www.national.com
DS005218-15
DS005218-14
DS005218-17
4
Typical Performance Characteristics
Spot Noise Voltage
vs Frequency
(Continued)
Spot Noise Current
vs Frequency
DS005218-21
Input Referred Noise Voltage
vs Source Resistance
DS005218-22
Noninverting Amp
DS005218-23
Noninverting Amp
DS005218-24
DS005218-25
Inverting Amp
DS005218-26
Capacitive loads greater than 50 pF must be isolated from
the output. The most straightforward way to do this is to put
a resistor in series with the output. This resistor will also prevent excess power dissipation if the output is accidentally
shorted.
Application Hints
The LM833 is a high speed op amp with excellent phase
margin and stability. Capacitive loads up to 50 pF will cause
little change in the phase characteristics of the amplifiers
and are therefore allowable.
5
www.national.com
Noise Measurement Circuit
DS005218-27
Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for power line noise.
Total Gain: 115 dB @f = 1 kHz
Input Referred Noise Voltage: en = V0/560,000 (V)
RIAA Preamp Voltage Gain, RIAA
Deviation vs Frequency
Flat Amp Voltage Gain vs
Frequency
DS005218-28
www.national.com
DS005218-29
6
Typical Applications
Adder/Subtracter
NAB Preamp
DS005218-33
VO = V1 + V2 − V3 − V4
Sine Wave Oscillator
DS005218-30
AV = 34.5
F = 1 kHz
En = 0.38 µV
A Weighted
NAB Preamp Voltage Gain
vs Frequency
DS005218-34
DS005218-31
Balanced to Single Ended Converter
DS005218-32
VO = V1–V2
7
www.national.com
Typical Applications
(Continued)
Second Order High Pass Filter
(Butterworth)
DS005218-35
Illustration is f0 = 1 kHz
Second Order Low Pass Filter
(Butterworth)
DS005218-36
Illustration is f0 = 1 kHz
www.national.com
8
Typical Applications
(Continued)
State Variable Filter
DS005218-37
Illustration is f0 = 1 kHz, Q = 10, ABP = 1
AC/DC Converter
DS005218-38
2 Channel Panning Circuit (Pan Pot)
Line Driver
DS005218-39
DS005218-40
9
www.national.com
Typical Applications
(Continued)
Tone Control
DS005218-41
Illustration is:
fL = 32 Hz, fLB = 320 Hz
fH = 11 kHz, fHB = 1.1 kHz
DS005218-42
RIAA Preamp
DS005218-3
Av = 35 dB
En = 0.33 µV
S/N = 90 dB
f = 1 kHz
A Weighted
A Weighted, VIN = 10 mV
@ f = 1 kHz
www.national.com
10
Typical Applications
(Continued)
Balanced Input Mic Amp
DS005218-43
Illustration is:
V0 = 101(V2 − V1)
11
www.national.com
Typical Applications
(Continued)
10 Band Graphic Equalizer
DS005218-44
fo(Hz)
C1
C2
R1
R2
32
0.12µF
4.7µF
75kΩ
500Ω
64
0.056µF
3.3µF
68kΩ
510Ω
125
0.033µF
1.5µF
62kΩ
510Ω
250
0.015µF
0.82µF
68kΩ
470Ω
500
8200pF
0.39µF
62kΩ
470Ω
1k
3900pF
0.22µF
68kΩ
470Ω
2k
2000pF
0.1µF
68kΩ
470Ω
4k
1100pF
0.056µF
62kΩ
470Ω
8k
510pF
0.022µF
68kΩ
510Ω
16k
330pF
0.012µF
51kΩ
510Ω
Note 6: At volume of change = ± 12 dB
Q = 1.7
Reference: “AUDIO/RADIO HANDBOOK”, National Semiconductor, 1980, Page 2–61
www.national.com
12
Physical Dimensions
inches (millimeters) unless otherwise noted
Molded Small Outline Package (M)
Order Number LM833M
NS Package Number M08A
Molded Dual-In-Line Package (N)
Order Number LM833N
NS Package Number N08E
13
www.national.com
LM833 Dual Audio Operational Amplifier
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
8-Lead (0.118” Wide) Molded Mini Small Outline Package
Order Number LM833MM
NS Package Number MUA08A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.