ETC 54ACTQ377LMQB

MICROCIRCUIT DATA SHEET
Original Creation Date: 07/16/96
Last Update Date: 03/19/99
Last Major Revision Date: 03/10/99
MN54ACTQ377-X REV 2A0
Octal D-Type Flip-Flop With Clock Enable
General Description
The ACTQ377 has 8 edge-triggered D-type flip-flops with individual D inputs and Q outputs.
The common buffered Clock (CP) input loads all flip-flops simultaneously, when the Clock
Enable (CE) is low. The register is fully edge-triggered. The state of each D input, one
set-up time before the LOW-to-HIGH clock transition, is transferred to corresponding
flip-flop's Q output. The CE input must be stable only one set-up time prior to the
LOW-to-HIGH clock transition for predictable operation.
The ACTQ377 utilizes NSC Quiet Series technology to guarantee quiet output switching and
improve dynamic threshold performance. FACT Quiet Series TM features GTO TM output contol
and undershoot corrector in addition to a split ground bus for superior performance.
Industry Part Number
NS Part Numbers
54ACTQ377
54ACTQ377DMQB*
54ACTQ377FMQB**
54ACTQ377LMQB***
Prime Die
D377
Controlling Document
5962-92190
Processing
Subgrp Description
MIL-STD-883, Method 5004
1
2
3
4
5
6
7
8A
8B
9
10
11
Quality Conformance Inspection
MIL-STD-883, Method 5004
1
Static tests at
Static tests at
Static tests at
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
Temp ( oC)
+25 C
+125 C
-55 C
+25 C
+125 C
-55 C
+25 C
+125 C
-55 C
+25 C
+125 C
-55 C
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
Features
-
Icc reduced by 50%
Guaranteed simultaneous switching noise level and dynamic threshold performance
Guaranteed pin-to-pin skew AC performance
Ideal for addressable register application
Clock enable for address and data synchronization applications
Eight edge-triggered D flip-flops
Buffered common clock
Outputs source/sink 24 mA
4 kV minimum ESD immunity
ACTQ has TTL-compatible inputs
Standard Military Drawing (SMD)
- 54ACTQ377: 5962-9219001MRX*, MSX**, M2X***
2
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
(Absolute Maximum Ratings)
(Note 1)
Supply Voltage (Vcc)
-0.5V to +7.0V
DC Input
Vi =
Vi =
DC Input
Diode Current (Iik)
-0.5V
Vcc +0.5V
Voltage (Vi)
-20 mA
+20 mA
-0.5V to Vcc +0.5V
DC Output Diode Current (Iok)
Vo = -0.5V
Vo = Vcc +0.5V
DC Output Voltage (Vo)
-20 mA
+20 mA
-0.5V to Vcc +0.5V
DC Output Source or Sink Current (Io)
+50 mA
DC Vcc or Ground Current per Output Pin (Icc to Ignd)
+50 mA
Storage Temperature (Tstg)
-65 C to +150 C
DC Latch-up Source or Sink Current
+300 mA
Junction Temperature (Tj)
CDIP
Note 1:
175 C
Absolute maximum ratings are those values beyond which damage to the
occur. The databook specification should be met, without exception,
the system design is reliable over its power supply, temperature and
loading variables. National does not recommend operation of FACT TM
databook specifications.
device may
to ensure that
output/input
circuits outside
Recommended Operating Conditions
(Note 1)
Supply Voltage (Vcc)
4.5V to 5.5V
Input Voltage (Vi)
0V to Vcc
Output Voltage (Vo)
0V to Vcc
Operating Temperature (Ta)
-55 C to +125 C
Minimum Input Edge Rate Delta V/Delta t
ACTQ Devices
Vin from 0.8V to 2.0V
Vcc @ 4.5V, 5.5V
Note 1:
125 mV/ns
All commercial packaging is not recommended for applications requiring greater than
2000 temperature cycles from -40C to +125C.
3
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
Electrical Characteristics
DC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: VCC 4.5V to 5.5V, Temperature Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED
BUT NOT TESTED.
SYMBOL
IIH
IIL
VOL
PARAMETER
High Level Input
Current
Low Level Input
Current
Low Level Output
Voltage
CONDITIONS
NOTES
VCC=5.5V, VIH=5.5V
PINNAME
MIN
MAX
UNIT
SUBGROUPS
1, 2 INPUT
0.1
uA
1
1, 2 INPUT
1.0
uA
2, 3
1, 2 INPUT
-0.1
uA
1
1, 2 INPUT
-1.0
uA
2, 3
VCC=4.5V, VIH=2.0V, VIL=0.8V,
IOL=50.0uA
1, 2 OUTPUT
.10
V
1, 2,
3
VCC=5.5V, VIH=2.0V, VIL=0.8V,
IOL=50.0uA
1, 2 OUTPUT
.10
V
1, 2,
3
VCC=4.5V, VIH=2.0V, VIL=0.8V,
IOL=24.0mA
1, 2 OUTPUT
.36
V
1
1, 2 OUTPUT
.50
V
2, 3
1, 2 OUTPUT
.36
V
1
1, 2 OUTPUT
.50
V
2, 3
1.65
V
1, 2,
3
VCC=5.5V, VIL=0.0V
VCC=5.5V, VIH=2.0V, VIL=0.8V,
IOL=24.0mA
VIOL
Dynamic Output
Current LOW
VCC=5.5V, VIH=5.5V, VIL=0.0V,
IOL=50.0mA
1,
OUTPUT
2, 5
VOH
High Level Output
Voltage
VCC=4.5V, VIH=2.0V, VIL=0.8V,
IOH=-50.0uA
1, 2 OUTPUT
4.40
V
1, 2,
3
VCC=5.5V, VIH=2.0V, VIL=0.8V,
IOH=-50.0uA
1, 2 OUTPUT
5.40
V
1, 2,
3
VCC=4.5V, VIH=2.0V, VIL=0.8V,
IOH=-24.0mA
1, 2 OUTPUT
3.86
V
1
1, 2 OUTPUT
3.70
V
2, 3
1, 2 OUTPUT
4.86
V
1
1, 2 OUTPUT
4.70
V
2, 3
3.85
V
1, 2,
3
VCC=5.5V, VIH=2.0V, VIL=0.8V,
IOH=-24.0mA
VIOH
Dynamic Output
Current HIGH
VCC=5.5V, VIH=5.5V, VIL=0.0V,
IOH=-50.0mA
1,
OUTPUT
2, 5
ICCH
Supply Current
VCC=5.5V, VIH=5.5V
1, 2 VCC
4.0
uA
1
1, 2 VCC
80
uA
2, 3
1, 2 VCC
4.0
uA
1
1, 2 VCC
80
uA
2, 3
1, 2 VCC
1.0
mA
1
1, 2 VCC
1.6
mA
2, 3
ICCL
ICCT
Supply Current
Supply Current
VCC=5.5V, VIL=0.0V
VCC=5.5V, VINH=3.4V
VIKL
VCC=4.5V, IKL=-18mA
1, 2 INPUT
-1.2
V
1, 2,
3
VIKH
VCC=4.5V, IKH=18mA
1, 2 INPUT
5.7
V
1, 2,
3
4
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
Electrical Characteristics
DC PARAMETERS(Continued)
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: VCC 4.5V to 5.5V, Temperature Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED
BUT NOT TESTED.
SYMBOL
PARAMETER
CONDITIONS
NOTES
PINNAME
VILD
Maximum Low Level
Dynamic Input
Voltage
VCC=5.0V, LOAD 50pF, 500 OHMS
6, 9 INPUT
VIHD
Minimum High
Level Dynamic
Input Voltage
VCC=5.0V, LOAD 50pF, 500 OHMS
6, 9 INPUT
VOLP
Quiet Output
Maximum Dynamic
VOL
VCC=5.0V, LOAD 50pF, 500 OHMS
6, 8 OUTPUT
VOLV
Quiet Output
Minimum Dynamic
VOL
VCC=5.0V, LOAD 50pF, 500 OHMS
VOHP
Quiet Output
Maximum Dynamic
VOH
VOHV
Quiet Output
Minimum Dynamic
VOH
MIN
MAX
SUBGROUPS
V
4
V
4
1.5
V
4
6, 8 OUTPUT
-1.2
V
4
VCC=5.0V, LOAD 50pF, 500 OHMS
6,
10
OUTPUT
VOH
+1.2
V
4
VCC=5.0V, LOAD 50pF, 500 OHMS
6,
10
OUTPUT
VOH
-2.2
V
4
5
0.8
UNIT
2.2
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
Electrical Characteristics
AC PARAMETER
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: CL=50pF, RL=500 OHMS, TR=3.0ns, TF=3.0ns, Temp range: -55C to +125C. NOTE: -55C TEMPERATURE, SUBGROUP
11 IS GUARANTEED BUT NOT TESTED.
SYMBOL
PARAMETER
tpLH
Propagation Delay
tpHL
Propagation Delay
CONDITIONS
NOTES
VCC=4.5V
VCC=4.5V
PINNAME
MIN
MAX
UNIT
SUBGROUPS
3,
CP-Qn
4, 7
1.5
9.0
ns
9
3,
CP-Qn
4, 7
1.5
10.0
ns
10, 11
3,
CP-Qn
4, 7
1.5
9.0
ns
9
3,
CP-Qn
4, 7
1.5
10.0
ns
10, 11
tw(L/H)
Pulse Width HIGH
or LOW
VCC=4.5V
6
CP
5.0
ns
9, 10,
11
ts(L/H)(1)
Setup Time HIGH
or LOW
VCC=4.5V
6
Dn - CP 4.0
ns
9, 10,
11
th(L/H)(1)
Hold Time HIGH or
LOW
VCC=4.5V
6
Dn - CP 1.5
ns
9, 10,
11
ts(L/H)(2)
Setup Time HIGH
or LOW
VCC=4.5V
6
CE-CP
5.0
ns
9, 10,
11
th(L/H)(2)
Hold Time HIGH or
LOW
VCC=4.5V
6
CE-CP
1.5
ns
9, 10,
11
Fmax
Maximum Clock
Frequency
VCC=4.5V
6
95
mHZ
9
6
85
mHZ
10, 11
Note 1:
SCREEN TESTED 100% ON EACH DEVICE AT +25C & +125C TEMPERATURE, SUBGROUPS 1, 2, 7,
Note 2:
Note
Note
Note
Note
Note
Note
Note
Note
8.
SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE,
SUBGROUPS A1, 2, 7, & 8.
3: SCREEN TESTED 100% ON EACH DEVICE AT +25C TEMPERATURE ONLY, SUBGROUP A9.
4: SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE,
SUBGROUPS A9 & 10.
5: TRANSMISSION LINE DRIVING TEST, GUARDBAND LIMITS SET FOR +25C, 2 MSEC DURATION MAX.
6: DESIGN CHARACTERIZATION DATA ONLY.
7: +25C & +125C MIN LIMITS GUARANTEED FOR 5.5V BY GUARDBANDING 4.5V MIN. LIMITS.
8: MAX NUMBER OF OUTPUTS DEFINED AS (N). DATA INPUTS ARE DRIVEN 0V TO 3V. ONE OUTPUT @
VOL.
9: MAX NUMBER OF DATA INPUTS (N) SWITCHING. N-1 INPUTS SWITCHING 0V TO 3V.
INPUT-UNDER-TEST SWITCHING 3V TO THRESHOLD (VILD), 0V TO THRESHOLD (VIHD), FREQ. = 1
MHz.
10: MAX NUMBER OF OUTPUTS DEFINED AS (N). DATA INPUTS ARE DRIVEN 0V TO 3V. ONE OUTPUT @
VOH.
6
MICROCIRCUIT DATA SHEET
MN54ACTQ377-X REV 2A0
Revision History
Rev
ECN #
1B0
M0001054 03/19/99
Rel Date
Originator
Donald B. Miller Corrected the SMD drawing number. The old rev (1A0)
incorrectly lists the SMD number as the 54ACT377 part
when it should be the SMD number for the 54ACTQ377
part.
Changes
2A0
M0003307 03/19/99
Linda Collins
Added VOHV and VOHP. Added note 10. Changed the IOH
test condition for VOH from -24uA to -24mA. Changed
the IOL test condition for VOL from 24uA to 24mA.
Changed the fMAX limit from 1.5nS to 95mHZ min. for
room temp and 85mHZ min. for temperature.
7