ETC LA75665NV

Ordering number : ENN7162
Monolithic Linear IC
LA75665NV
VIF/SIF IF Signal-Processing Circuit with TV/VCR PAL
and NTSC Multisound Support
Overview
The LA75665NV is a VIF/SIF IC that supports PAL and
NTSC multisound and that adopts a semi-adjustment-free
system. To simplify adjustment, the VIF block adopts a
technique in which AFT adjustment is no longer required
by VCO adjustment. The SIF block supports audio multidetection by adopting a PLL detection technique. The SIF
block provides 4 inputs with IC internal switching for easy
design of multi-sound systems. Additionally, these
switches can also be used for video system sound trap
switching. The LA75665NV also includes a buzz
canceller that suppresses Nyquist buzz to achieve
improved audio quality.
[First SIF Block]
• First SIF amplifier
• First SIF detector
• AGC
[SIF Block]
• Multiple input switch
• Limiter amplifier
• PLL FM detector
Package Dimensions
unit: mm
3175B-SSOP24
[LA75665NV]
Features
7.8
24
7.6
0.5
0.15
0.22
(1.3)
0.65
1.5max
[VIF Block]
• VIF amplifier
• PLL detector
• BNC
• RF AGC
• EQ amplifier
• AFT
• IF AGC
• Buzz canceller
1
(0.33)
0.1
Functions
5.6
• No coils are used in the AFT and SIF blocks, making
these circuits adjustment free.
• PAL / NTSC multisound system can be constructed
easily.
• Built-in buzz canceller for excellent audio performance
SANYO: SSOP24 (275mil)
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
D2601TN (OT) No. 7162-1/12
LA75665NV
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Maximum supply voltage
VCC max
6
Circuit voltage
V7, V10,
VCC
I1
Circuit current
Allowable power dissipation
V
V
–2
mA
I13
–3
mA
I18
–10
mA
400
mW
Pd max
Ta ≤ 85°C, When mounted on a printed circuit board*
Operating temperature
Topr
–20 to +85
°C
Storage temperature
Tstg
–55 to +150
°C
Ratings
Unit
Note: * Size: 65 × 72 × 1.6
mm3,
Material: paper/phenol composite
Operating Conditions at Ta = 25°C
Parameter
Symbol
Recommended supply voltage
VCC
Operating supply voltage range
VCC op
Conditions
5
V
4.6 to 5.5
V
No. 7162-2/12
LA75665NV
Operating Characteristics at Ta = 25°C, VCC = 5 V, fp = 38.9 MHz
Parameter
Symbol
Conditions
Ratings
min
typ
Unit
max
[VIF Block]
Circuit current
I3
39
46
Maximum RF AGC voltage
V9H
4.5
4.9
Minimum RF AGC voltage
V9L
Input sensitivity
VIN
AGC range
GR
VIN max
Maximum allowable input
No-signal video output voltage
Sync tip voltage
Video output level
S1 = OFF
53
mA
0
0.5
V
29
35
41
dBµV
45
50
dB
95
100
dBµV
V
V13
3.2
3.5
3.8
V13 tip
0.8
1.0
1.2
V
VO
1.65
1.85
2.25
Vp-p
V
Black noise threshold voltage
VBTH
0.3
0.6
0.9
Black noise clamp voltage
VBCL
1.5
1.8
2.1
Video signal-to-noise ratio
S/N
48
52
C-S beat
IC-S
Frequency characteristics
fC
6 MHz
V
V
dB
44
49
dB
–3
–1.5
dB
Differential gain
DG
3
8
%
Differential phase
DP
3
8
deg
AFT voltage with no input signal
4
4.5
5.0
V
Maximum AFT voltage
V10H
4.2
4.8
5.0
V
Minimum AFT voltage
V10L
0
0.1
0.2
V
AFT detection sensitivity
Sf
19
25
32
mV/kHz
VIF input resistance
Ri
38.9 MHz
1.5
VIF input capacitance
Ci
38.9 MHz
3
APC pull-in range (U)
fPU
APC pull-in range (L)
V10
1.0
fPL
kΩ
pF
1.5
MHz
–1.5
–0.8
AFT tolerance frequency 1
dfa1
–200
0
+200
VCO 1 maximum variability range (U)
dfu
1.3
1.5
VCO 1 maximum variability range (L)
dfl
VCO control sensitivity
B
Drift when the AFT switch is on
1.25
kHz
MHz
–1.5
–0.75
2.3
5.0
Drift
MHz
3
MHz
kHz/mV
s
[First SIF Block]
Conversion gain
VG
30
33
36
dB
5.5 MHz output level
SO
95
135
190
mVrms
27
Maximum first SIF input
SIN max
55
mVrms
First SIF input resistance
RIN(SIF)
33.4 MHz
2
kΩ
First SIF input capacitance
CIN(SIF)
33.4 MHz
3
pF
[SIF Block]
Limiting sensitivity
VIi(lim)
FM detector output voltage
VO(FM)
AM rejection ratio
AMR
Total harmonic distortion
THD
SIF S/N
FM detector output DC voltage
5.5 MHz ± 30 kHz
S/N (FM)
FMDC
450
50
36
42
dBµV
570
720
mVrms
60
0.2
dB
1.5
%
55
60
dB
2.15
2.5
2.85
V
7
dB
[SIF Switch Block] Switches A, B, and C: H = open, L = ground
NTSC mode 6-dB amplifier
NTSW
5
6
SIF crosstalk 21
CT21
51
57
dB
SIF crosstalk 22
CT22
51
57
dB
SIF crosstalk 23
CT23
51
57
dB
SIF crosstalk 24
CT24
51
57
SW (L)
1.0
1.5
Switch threshold low-level voltage
dB
2.0
V
No. 7162-3/12
LA75665NV
SIF IN (6.5MHz) /RFAGC VR
SIF IN (6.0MHz)
SIF IN (5.5MHz)
SIF IN (4.5MHz)
FM FILTER
1st SIF OUT
COMP OUT
APC
NT VIDEO IN
PAL VIDEO IN
EQ FILTER
VIDEO OUT
Pin Assignment
24
23
22
21
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
9
10
11
12
FM DET OUT
SIF FILTER
VCC
GND
VIF IN
VIF IN
IFAGC
1st SIF IN
RFAGC OUT
AFT OUT
VCO COIL
VCO COIL
LA75665NV
Top view
A12481
8.2 µH
330 Ω
5.5 MHz, 6.0 MHz, 6.5 MHz
6.5 MHz 6.0 MHz 5.5 MHz 4.5 MHz
150 Ω
150 Ω
30 pF
+
24
23
22
+
21
20
19
18
17
16
15
RF
AGC
14
13
EQ
AMP
INPUT SW
LIM
AMP
VIDEO
OUT
3 kΩ
4.5 MHz
47 µH
1 µF
0.01 µF
0.01 µF
A
0.01 µF
2.2 kΩ
2.2 kΩ
560 Ω
2.2 kΩ
B
15 µH
330 Ω
2.2 kΩ
C
0.47 µF
330 Ω
330 Ω
330 Ω
Application Circuit Diagram
IF
AGC
VIDEO
DET
1ST SIF
DET
F
Switch
B
H
H
L
L
H
L
H
L
C
H
L
H
L
H
L
L
H
5.5 MHz
6.0 MHz
5
6
8
9
10
11
12
RFAGC
OUT
0.01 µF
SAW
(S)
0.01 µF
0.01 µF
100 µF
+
30 kΩ
1 µF
6.5 MHz
7
100 kΩ 100 kΩ
4
SAW(P)
VCC
A
H
H
H
H
L
L
L
L
3
+
0.01 µF
5.1 kΩ
2
VCO
AFT
0.022 µF
1
AUDIO
OUT
1ST
AMP
VIF
FM
DET
AFT
OUT
A12482
4.5 MHz
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
H : OPEN
L : GND
No. 7162-4/12
A
B
C
AUDIO
OUT
28 kΩ
24
0.01 µF
1
2 kΩ
100 Ω
28 kΩ
15 kΩ
5.1 kΩ
50 kΩ-B
0.01 µF 0.01 µF 0.01 µF
2.2 kΩ
2.2 kΩ
2.2 kΩ
6.5 MHz
330 Ω
1 µF
100 Ω
28 kΩ
15 kΩ
+
VCC
2
23
6.0 MHz
100 µF
+
100 Ω
28 kΩ
3
0.01 µF
1 kΩ 1 kΩ
100 Ω
15 kΩ
47 µH
4
1.5 kΩ
2.5 kΩ
1 µF
330 Ω
21
4.5 MHz
30 pF
3.6 V
330 Ω
22
5.5 MHz
15 kΩ
330 Ω
+
5
1 kΩ
20
SAW (P)
1 kΩ
15 pF
6
1 kΩ
1.5 kΩ 2 kΩ
2 pF
19
560 Ω
7
+
8
100 Ω
9
1 kΩ 1 kΩ 1 kΩ
17
0.47 µF
4.5 MHz
16
RFAGC
OUT
10
200 Ω
30 kΩ
0.01 µF
15
200 Ω
5.5 MHz, 6.0 MHz, 6.5 MHz
15 µH
SAW
(S)
2 kΩ
2 kΩ
0.022 µF
10 kΩ
1 kΩ
2 kΩ
18
150 Ω
330 Ω
150 Ω
8.2 µH
11
1 kΩ
1 kΩ
VCO COIL
1.2 kΩ
9.2 kΩ
2 kΩ
14
1.2 kΩ
0.01 µF
12
13
3 kΩ
VIDEO
OUT
A12483
100 kΩ
AFT
OUT
100 kΩ
2.2 kΩ
LA75665NV
Internal Equivalent Circuit Diagram
No. 7162-5/12
LA75665NV
AC Characteristics Test Circuit Diagram
51
51
51
0.01 µF
0.01 µF
0.01 µF
VIDEO
OUT
(A)
1st SIF OUT
(C)
SWA
SWB
100 kΩ
51
0.01 µF
2nd SIF IN
23
22
21
20
0.47 µF
+
19
18
330 Ω
150 Ω
560 Ω
24
1 µF
+
RF
vr 20K-B
17
16
330 Ω
S1
SWC
15
14
EQ
AMP
INPUT SW
LIM
AMP
13
RF
AGC
IF
AGC
VIDEO
DET
1st SIF
DET
F
10
51 Ω
RFAGC
OUT
(F)
IF AGC
VIF IN
11
12
MA6389
100 kΩ
9
1000 pF
51 Ω
0.01 µF
100 µF
8
100 kΩ
GND
7
30 kΩ
1 µF
+
+
6
0.01 µF
5
0.022 µF
4
0.01 µF
3
0.01 µF
(M)
(D)
2
0.01 µF
1
VCO
AFT
0.01 µF
FM
DET
FM DET OUT 5.1 kΩ
1st
AMP
VIF
AMP
AFT
OUT
(B)
1st SIF IN
VCC
GND
A12484
24
23
22
21
20
19
18
17
330Ω
330Ω
0.01 µF
10kΩ
0.01 µF
Input Impedance Test Circuit Diagram (VIF and first SIF input impedance)
16
15
14
13
9
10
11
12
LA75665NV
8
VIF IN
100kΩ
0.01 µF
0.01 µF
7
100kΩ
6
0.01 µF
5
0.01 µF
4
0.01 µF
3
0.01 µF
2
0.01 µF
1st SIF IN
100 µF
Impedance analyzer
0.01 µF
0.01 µF
1
+
VCC
A12485
No. 7162-6/12
LA75665NV
Pin Functions
Pin No.
Symbol
Pin function
Equivalent circuit
• Audio FM detector output
This circuit includes an internal 300 Ω resistor in series with the
emitter-follower output.
• Stereo applications
1
FM DET OUT
The input impedance may be reduced according to the
applications that input this signal to a stereo decoder. This can
result in distortion in the left and right signals and a degradation
of the stereo characteristics. If this problem occurs, add a
resistor between pin 1 and ground.
R2
1
300 Ω
R1
C
10 kΩ
R1 ≥ 5.1 kΩ
• Mono applications
Forms an external deemphasis circuit.
A12486
t = CR2
2
SIF FILTER
• Connection for a filter that holds the FM detector output DC
voltage at a fixed level. Normally, a 1-µF electrolytic capacitor is
used. To improve the low band (around 50 Hz) frequency
characteristics, increase the value of this capacitor (C1).
1 kΩ
1 kΩ
The FM detector output level can be reduced and the FM
dynamic range increased by inserting this resistor in series with
the capacitor.
2
+
C1
R
A12487
1 kΩ
1 kΩ
• VIF amplifier input.
5
6
VIF IN
The input circuit is constructed as a balanced input, and the
input has the following impedance characteristics:
R ≈ 1.5 kΩ
C ≈ 3 pF
5
6
A12488
Continued on next page.
No. 7162-7/12
LA75665NV
Continued from preceding page.
Pin No.
Symbol
Pin function
Equivalent circuit
2 kΩ
• IF AGC filter connection.
7
IF AGC
1 kΩ
The AGC voltage is created at pin 7 from the signal to which
peak detection was applied by the internal AGC detector.
Additionally, the IC includes an internal second AGC filter (a
lag-lead filter) used to create a dual time constant. A 0.022 µF
capacitor is used as the external capacitor. The value of this
capacitor must be adjusted according to measurement of the
sag, AGC speed, and other circuit aspects.
10 kΩ
7
C1
A12489
• First SIF input.
A DC cut capacitor must be inserted in the input to this circuit.
8
1st SIF IN
When a SAW filter is used: The first SIF sensitivity can be
increased by inserting an inductor between the SAW and the IC
to match the SAW output and IC input capacitances.
2 kΩ
2 kΩ
When an intercarrier system is used: This pin must be
connected to ground through a capacitor.
8
A12490
500 Ω
VCC
• RF AGC output.
9
RF AGC OUT
This output controls the tuner RF AGC. This is an opencollector output with an inserted 100-Ω protective resistor.
Determine the value of the external bleeder resistor to match
the tuner specifications.
9
100 Ω
3 pF
A12491
• AFT output.
10
AFT OUT
The AFT center voltage is created with an external bleeder
resistor. The AFT gain increases as the value of this bleeder
resistor increases. The value of this resistor must not exceed
390 kΩ. This circuit includes a control function that controls the
AFT voltage to be equal to the center voltage in weak field
reception conditions.
1 kΩ
10
A12492
Continued on next page.
No. 7162-8/12
LA75665NV
Continued from preceding page.
Pin No.
Symbol
Pin function
Equivalent circuit
12
11
12
11
• VCO tank circuit used for video detection.
VCO
1.2 kΩ 1.2 kΩ
See the separately provided documentation for the tank circuit
coil (inductor) specifications.
A12493
• Equalizer circuit. This circuit corrects the video signal frequency
characteristics.
• Notes on equalizer amplifier design:
13
VIDEO OUT
The equalizer amplifier is designed as a voltage follower
amplifier with a gain of about 2.3 dB. When the frequency
characteristics are corrected, connect an inductor, a capacitor,
and a resistor in series between pin 14 and ground.
14
EQ FILTER
The equalizer amplifier gain is given by:
2 kΩ
1 kΩ
13
9.2 kΩ
R1
AV = —— + 1
Z
14
Here, R1 is an IC internal resistor with a value of 1 kΩ. Select Z
according to the desired characteristics. However, care is
required to prevent distortion at the resonant point determined
by Z, where the gain is maximum.
C
L
Z
R
A12494
15
PAL VIDEO IN
16
NT VIDEO IN
• Equalizer amplifier inputs.
Pin 15 is for PAL, and pin 16 for NTSC format signals. These
inputs are linked to and switched by the SIF switches.
15
16
200 Ω
200 Ω
A12495
FRO
APC
• PLL detector APC filter connection.
17
APC FILTER
The APC time constants are switched internally in the IC. When
locked, the VCO is controlled over the path A, and the loop gain
is reduced. When unlocked and during weak field reception, the
VCO is controlled over the path B, thus increasing the loop
gain.
A
1 kΩ 1 kΩ 1 kΩ
We recommend values of:
R = 150 to 390 Ω, and
B
C = 0.47 µF
for the loop filter constants.
17
A12496
Continued on next page.
No. 7162-9/12
LA75665NV
Continued from preceding page.
Pin No.
Symbol
Pin function
Equivalent circuit
15pF
• Output for the video signal that includes the SIF carrier.
18
COMP OUT
A resistor must be inserted between pin 18 and ground to
acquire an adequate drive capability.
1.5 kΩ 2 kΩ
R ≥ 470 Ω
2pF
18
A12497
1 kΩ
• First SIF output
19
1st SIF OUT
19
The signal output from this pin is passed through a bandpass
filter and input to the SIF circuit. This is an emitter-follower
output.
A12498
• The FM detector signal-to-noise ratio can be improved by
inserting a filter in the FM detector bias line.
20
FM FILTER
C1 should have a value of 0.47 µF or greater, and 1 µF is
recommended .
2.5 kΩ
20
+
1.5 kΩ
C1
If the FM detector is not used, pin 20 must be connected to
ground through a 2-kΩ resistor. This stops the FM detector
VCO circuit.
A12499
• SIF inputs.
Four input pins are provided to support multi-side systems, and
a switching function is also included. Since buzzing and bass
beating can occur if interference signals, such as the video
signal or the chrominance signal, enter these pins, extra care
must be taken in designing the input circuit pattern layout. Note
that pin 24 also functions as the RF AGC adjustment pin. This
pin sets the tuner RF AGC operating point. Also, the FM output
and the video output can be muted at the same time by setting
this pin to the ground level.
RF AGC VR
28 kΩ
15 kΩ
11 kΩ
30 kΩ
28 kΩ
28 kΩ
15 kΩ
11 kΩ
11 kΩ
4.5 MHz
100 Ω
6.0 MHz 6.5 MHz
●
100 Ω
5.5 MHz
100 Ω
SIF IN (6.5 MHz)
Switch
B
C
H
H
H
L
L
H
L
L
H
H
L
L
H
L
L
H
30 kΩ
24
A
H
H
H
H
L
L
L
L
12 kΩ
SIF IN (6.0 MHz)
30 kΩ
SIF IN (5.5 MHz)
23
28 kΩ
SIF IN (4.5 MHz)
22
VBGZ=3.6
100 Ω
21
VCC
●
21
●
●
●
●
●
●
●
●
●
●
●
●
22
4.5MEG
23
5.5MEG
6.0MEG
24
6.5MEG
●
SWA
SWB
SWC
A12500
No. 7162-10/12
LA75665NV
Notes on Sanyo SAW Filters
There are two types of SAW filters, which differ in the piezoelectric substrate material, as follows:
1. Lithium tantalate (LiTaO3) SAW filter
TSF11 ■ ■ ······ Japan
TSF12 ■ ■ ······ US
Although lithium tantalate SAW filters have the low temperature coefficient of –18 ppm/°C, they suffer from a large
insertion loss. However, it is possible, at the cost of increasing the number of external components required, to minimize
this insertion loss by using a matching circuit consisting of coils and other components at the SAW filter output. At the
same time as minimizing insertion loss, this technique also allows the frequency characteristics, level, and other aspects
to be varied, and thus provides increased circuit design flexibility. Also, since the SAW filter reflected wave level is
minimal, the circuit can be designed with a small in-band ripple level.
2. Lithium niobate (LiNbO3) SAW filter
TSF52 ■ ■ ······ US
TSF53 ■ ■ ······ PAL
Although lithium niobate SAW filters have the high temperature coefficient of –72 ppm/°C, they feature an insertion loss
about 10 dB lower than that of lithium tantalate SAW filters. Accordingly, there is no need for a matching circuit at the
SAW filter output. Although the in-band ripple is somewhat larger than with lithium tantalate SAW filters, since they
have a low impedance and a small field slew, they are relatively immune to influences from peripheral circuit
components and the geometry of the printed circuit board pattern. This allows stable out-of-band trap characteristics to be
acquired. Due to the above considerations, lithium tantalate SAW filters are used in applications for the US and Japan
that have a high IF frequency, and lithium niobate SAW filters are used in PAL and US applications that have a low IF
frequency.
Notes on SAW Filter Matching
In SAW filter input circuit matching, rather than matching the IF frequency, flatter video band characteristics can be
acquired by designing the tuning point to be in the vicinity of the audio carrier rather than near the chrominance carrier.
The situation shown in figure on the right makes it easier to acquire flat band characteristics than that in figure on the left.
SAW filter characteristics
The high-band is
extended
The high-band is reduced
Frequency
Frequency
A12501
With the tuning set to the IF frequency
With the tuning set to the vicinity of S and C
Coil Specifications
JAPAN
S
f = 58.75 MHz
US
t=5t
0.12ø
C = 24 pF
f = 45.75 MHz
S
PAL
t=6t
0.12ø
C = 24 pF
S
f = 38.9 MHz
t=7t
0.12ø
C = 24 pF
VCO coils
A12502
SAW filters (split)
SAW filters (inter)
A12503
A12504
Test production No. V291XCS-3220Z
Toko Co., Ltd
Test production No. V291XCS-3188Z
Toko Co., Ltd
Test production No. V292GCS-7538Z
Toko Co., Ltd
Picture
Picture
Picture
TSF1137U
TSF1241
TSF5315
SOUND
SOUND
SOUND
TSF5220
TSF5321
TSF5221
Toko Co., Ltd. 2-1-17 Higashi-yukigaya, Ohota-ku, Tokyo, Japan TEL: +81-3-3727-1167
TSF5344
No. 7162-11/12
LA75665NV
Notes on VCO Tank Circuits
1. Built-in capacitor VCO tank circuits
When the power is turned on, the heat generated by the IC is transmitted through the printed circuit board to the VCO
tank circuit. At this point, the VCO coil frame functions as a heat sink and the IC heat is dissipated. As a result, it
becomes more difficult to transmit heat to the VCO tank cricuit's built-in capacitor, and the influence of drift at power
on is reduced. Therefore, it suffices to design the circuit so that the coil and capacitor thermal characteristics cancel.
Ideally, it is better to use a coil with a core material that has low temperature coefficient characteristics.
2. External capacitor VCO tank circuits
When an external capacitor is used, heat generated by the IC is transmitted through the printed circuit board directly
to the VCO tank circuit external capacitor. While this capacitor is heated relatively early after the power is turned on,
the coil is not influenced as much by this heat, and as a result the power-on drift is increased. Accordingly, a coil
whose core material has low temperature coefficient characteristics must be used. It is also desirable to use a
capacitor with similarly low temperature coefficient characteristics.
Note: Applications that use an external capacitor here must use a chip capacitor. If an ordinary capacitor is used,
problems such as the oscillator frequency changing with the capacitor orientation may occur.
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products (including technical data, services) described or contained
herein are controlled under any of applicable local export control laws and regulations, such products must
not be exported without obtaining the export license from the authorities concerned in accordance with the
above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification”
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of December, 2001. Specifications and information herein are
subject to change without notice.
PS No. 7162-12/12