Open-Drain Microprocessor Supervisory Circuit in 4-Lead SOT-143 ADM6315 FEATURES FUNCTIONAL BLOCK DIAGRAM VCC GND VREF ADM6315 RESET RESET CIRCUITRY MR DEBOUNCE 00081-001 Specified over temperature Low power consumption (5 μA typical) Precision voltage monitor of voltages from 2.5 V to 5 V at 100 mV increments Reset assertion down to VCC > 1 V Reset timeout periods: 1 ms, 20 ms, 140 ms, or 1120 ms (minimum) Built-in manual reset Pin compatible with the ADM811 Available in SOT-143 package Figure 1. APPLICATIONS VCC SYSTEM POWER ADM6315 RESET MR 10kΩ MICROPROCESSOR SYSTEM RESET GND GND 00081-011 Microprocessor systems Controllers Intelligent instruments Automotive systems Safety systems Portable instruments Figure 2. Typical Operating Circuit GENERAL DESCRIPTION The ADM6315 is a reliable voltage-monitoring device that is suitable for use in most voltage-monitoring applications. The ADM6315 is designed to monitor as little as a 1.8% degradation of a power supply voltage. The ADM6315 can monitor all voltages (at 100 mV increments) from 2.5 V to 5 V. Included in this circuit is a debounced manual reset input. RESET can be activated using an ordinary switch (pulling MR low), a low input from another digital device, or a degradation of the supply voltage. The manual reset function is very useful, especially if the circuit in which the ADM6315 is operating enters into a state that can be detected only by the user. Allowing the user to reset a system manually can reduce the damage or danger that could otherwise be caused by an out-of-control or locked-up system. The ADM6315 is available in a cost- and space-efficient SOT-143 package. Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©1999–2007 Analog Devices, Inc. All rights reserved. ADM6315 TABLE OF CONTENTS Features .............................................................................................. 1 Typical Performance Characteristics ..............................................6 Applications....................................................................................... 1 Theory of Operation .........................................................................7 Functional Block Diagram .............................................................. 1 Interfacing to Output of Other Devices .....................................7 General Description ......................................................................... 1 Benefits of a Very Accurate RESET Threshold .............................7 Revision History ............................................................................... 2 Detailed Description.....................................................................7 Specifications..................................................................................... 3 Manual Reset Input .......................................................................7 Absolute Maximum Ratings............................................................ 4 Transient Immunity ......................................................................7 Thermal Resistance ...................................................................... 4 Outline Dimensions ..........................................................................8 ESD Caution.................................................................................. 4 Ordering Guide .............................................................................8 Pin Configuration and Function Descriptions............................. 5 REVISION HISTORY 9/07—Rev. D to Rev. E Changes to Absolute Maximum Ratings ....................................... 4 Updated Outline Dimensions ......................................................... 8 Changes to Ordering Guide ............................................................ 8 4/06—Rev. C to Rev. D Updated Format..................................................................Universal Updated Outline Dimensions ......................................................... 8 Changes to Ordering Guide ............................................................ 8 12/03—Rev. B to Rev. C Edit to Absolute Maximum Ratings............................................... 3 Edits to Ordering Guide .................................................................. 4 Deleted Table I and Table II ............................................................ 6 Deleted Table III and Table IV........................................................ 7 Updated Outline Dimensions ......................................................... 8 2/03—Rev. A to Rev. B Edits to Features.................................................................................1 Edits to Specifications .......................................................................2 Edits to Absolute Maximum Ratings ..............................................3 Edits to Ordering Guide ...................................................................3 Edits to Table I and Table II .............................................................6 Edits to Table III and Table IV.........................................................7 Updated Outline Dimensions..........................................................8 10/01—Rev. 0 to Rev. A Edits to Table III ................................................................................7 Edits to Table IV ................................................................................7 1999—Revision 0: Initial Version Rev. E | Page 2 of 12 ADM6315 SPECIFICATIONS VCC = full operating range, TA = TMIN to TMAX, VCC typical = 5 V, unless otherwise noted. Table 1. Parameter SUPPLY Operating Voltage VCC Supply Current Min Typ 1 Max Unit Test Conditions/Comments 5.5 12 15 10 12 VTH + 1.8% VTH + 2.5% VTH + 3.5% TA = −40°C to +85°C VCC = 5.5 V, no load, TA = −40°C to +85°C VCC = 5.5 V, no load, TA = −40°C to +125°C VCC = 3.6 V, no load, TA = −40°C to +85°C VCC = 3.6 V, no load, TA = −40°C to +125°C TA = 25°C TA = −40°C to +85°C TA = −40°C to +125°C RESET THRESHOLD TEMPERATURE COEFFICIENT 60 V μA μA μA μA V V V ppm/°C VCC TO RESET DELAY RESET ACTIVE TIMEOUT PERIOD ADM6315xxD1 35 μs VCC = falling at 1 mV/μs ms ms ms ms ms ms ms ms TA = −40°C to +85°C TA = −40°C to +125°C TA = −40°C to +85°C TA = −40°C to +125°C TA = −40°C to +85°C TA = −40°C to +125°C TA = −40°C to +85°C TA = −40°C to +125°C VTH > 4 V (VIL) VTH > 4 V (VIH) VTH < 4 V (VIL) VTH < 4 V (VIH) 100 V V V V μs ns ns kΩ 0.4 0.3 0.3 1 V V V μA VCC > 4.25 V, ISINK = 3.2 mA VCC > 2.5 V, ISINK = 1.2 mA VCC > 1 V, ISINK = 80 μA VCC > VTH, RESET deasserted 5 4 RESET VOLTAGE THRESHOLD (VTH) ADM6315xxD2 ADM6315xxD3 ADM6315xxD4 MANUAL RESET Input Threshold VTH − 1.8% VTH − 2.5% VTH − 3.5% 1 0.8 20 16 140 112 1120 896 VTH 1.4 28 200 1570 2 2.4 40 48 280 336 2240 2688 0.8 2.4 0.3 × VCC 0.7 × VCC Minimum Input Pulse Glitch Rejection To Reset Delay Pull-Up Resistance RESET OUTPUT Output Voltage Output Leakage Current 1 32 100 500 63 Rev. E | Page 3 of 12 ADM6315 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. THERMAL RESISTANCE Table 2. θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Parameter Terminal Voltage (with Respect to Ground) VCC All Other Inputs Input Current VCC Output Current RESET Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering, 10 sec) Vapor Phase (60 sec) Infrared (15 sec) ESD Rating Rating Table 3. Thermal Resistance −0.3 V to +6 V −0.3 V to +6 V Package Type 4-Lead SOT-143 20 mA ESD CAUTION 20 mA −40°C to +125°C −65°C to +160°C 300°C 215°C 220°C 2.5 kV Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. E | Page 4 of 12 θJA 330 Unit °C/W ADM6315 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS RESET 2 ADM6315 TOP VIEW (Not to Scale) 4 VCC 3 MR 00081-002 GND 1 Figure 3. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 2 Mnemonic GND RESET 3 MR 4 VCC Description Ground Reference for All Signals, 0 V. Active Low Logic Output. RESET remains low while VCC is below the reset threshold or when MR is low. RESET then remains low for a minimum of 1 ms, 20 ms, 140 ms, or 1120 ms after VCC rises above the reset threshold and MR is high. Manual Reset. This active low debounced input ignores input pulses of 100 ns (typical) and is guaranteed to accept input pulses of greater than 1 μs. Leave floating when not used. Monitored Supply Voltage. Rev. E | Page 5 of 12 ADM6315 TYPICAL PERFORMANCE CHARACTERISTICS 50 8 6 VCC = 3V 4 2 –20 0 20 40 60 80 100 125 TEMPERATURE (°C) 20 15 10 5 0 200 300 400 500 600 700 800 900 1000 NORMALIZED RESET THRESHOLD (V) 350 300 1.000 250 200 VOD = 20mV 150 VOD = 125mV 50 0 20 40 60 80 100 125 TEMPERATURE (°C) 00081-004 VOD = 200mV –20 0.990 –40 –20 0 20 40 60 80 100 00081-007 0.995 100 125 TEMPERATURE (°C) Figure 8. Normalized Reset Threshold vs. Temperature (VCC Falling) Figure 5. Power-Down Reset Delay vs. Temperature 12 1.04 10 SUPPLY CURRENT (µA) 1.06 1.02 1.00 0.98 8 +85°C 6 –40°C +25°C 4 2 –20 0 20 40 60 TEMPERATURE (°C) 80 100 125 00081-005 0.96 0.94 –40 100 1.005 400 POWER-DOWN RESET DELAY (µs) 25 Figure 7. Maximum Transient Duration vs. RESET Comparator Overdrive 450 NORMALIZED RESET TIMEOUT PERIOD (ms) 30 RESET COMPARATOR OVERDRIVE, (VTH – VCC) (mV) Figure 4. Supply Current vs. Temperature 0 –40 35 0 00081-003 0 –40 VCC = 1V 40 Figure 6. Normalized Reset Timeout Period vs. Temperature (VCC Rising) Rev. E | Page 6 of 12 0 0 1 2 3 4 SUPPLY VOLTAGE (V) Figure 9. Supply Current vs. Supply Voltage 5 00081-008 IDD (µA) VCC = 5.5V 45 00081-012 MAXIMUM TRANSIENT DURATION (µs) 10 ADM6315 THEORY OF OPERATION INTERFACING TO OUTPUT OF OTHER DEVICES MANUAL RESET INPUT The ADM6315 series is designed to integrate with as many devices as possible. One feature of the ADM6315 is the RESET opendrain output, which can sink current from sources with a voltage greater than the VCC of the ADM6315 input, making it suitable for use in more diverse applications. The ADM6315 also provides an additional input, MR. This input can be used either as a means for the system operator to reset the system manually via a switch or for a digital circuit to reset the system. BENEFITS OF A VERY ACCURATE RESET THRESHOLD Because the ADM6315 series can operate effectively even when there are large degradations of the supply voltages (due to an accurate internal voltage reference circuit), the possibility of a malfunction during a power failure is greatly reduced. The MR input (typically) ignores negative-going pulses that are faster than 100 ns, and it is guaranteed to accept any negativegoing input pulse of a duration greater than or equal to 1 μs. If MR is connected to long cables or is used in a noisy environment, placing a 1 μF decoupling capacitor between the MR input and ground further improves the glitch immunity of the ADM6315. VCC VCC TRIP POINT (MIN) VCC TRIP POINT (MIN) VCC VCC TO RESET DELAY VOL 00081-009 RESET VCC TRIP POINT (MAX) VCC TRIP POINT RESET ACTIVE TIMEOUT RESET Figure 10. VCC Power-Down/Brownout Timing Diagram 00081-010 VCC TRIP POINT (MAX) VCC TRIP POINT Figure 11. VCC Power-Up Timing Diagram DETAILED DESCRIPTION The ADM6315 is designed to protect the integrity of a system’s operation by ensuring the proper operation of the system during power-up, power-down, and brownout conditions. When the ADM6315 is powered up, the RESET output of the ADM6315 remains low for a period typically equal to the RESET active timeout period. This feature allows adequate time for the system to power up correctly and for the power supply to stabilize before any devices are brought out of reset and allowed to begin executing instructions. Initializing a system in this way provides a more reliable startup for microprocessor systems. TRANSIENT IMMUNITY As well as being an accurate reset circuit, the ADM6315 has good immunity from negative-going transients (see Figure 7). Because of this characteristic, the ADM6315 is suitable for use in noisy environments. Figure 7 shows the RESET comparator overdrive (the maximum magnitude of negative-going pulses with respect to the typical reset threshold) vs. the pulse duration without a reset. When a brownout condition occurs (assuming VCC is falling at 1 mV/μs), the ADM6315 produces a reset in 35 μs typical. Producing a reset this fast means that the entire system can be reset together before any part of the system’s voltage falls below its recommended operating voltage. This system reset can avoid dangerous and/or erroneous operation of a microprocessorbased system. Rev. E | Page 7 of 12 ADM6315 OUTLINE DIMENSIONS 1.40 1.30 1.20 4 3 1 2 2.64 2.10 1.92 BSC 1.07 0.90 0.75 1.22 0.80 0.100 0.013 0.89 0.76 0.50 0.30 0.20 0.08 SEATING PLANE 0.54 REF 0.60 0.50 0.40 8° 0° 073105-A 0.20 BSC 3.04 2.90 2.80 COMPLIANT TO JEDEC STANDARDS TO-253-AA Figure 12. 4-Lead Small Outline Transistor Package [SOT-143] (RA-4) Dimensions shown in millimeters ORDERING GUIDE Model ADM6315-46D1ARTRL7 ADM6315-46D1ART-RL ADM6315-46D1ARTZR71 ADM6315-45D1ARTRL7 ADM6315-45D1ART-RL ADM6315-45D1ARTZR7 1 ADM6315-44D1ARTRL7 ADM6315-44D1ART-RL ADM6315-31D1ARTRL7 ADM6315-31D1ART-RL ADM6315-31D1ARTZR71 ADM6315-31D1ARTZRL1 ADM6315-29D1ARTRL7 ADM6315-29D1ART-RL ADM6315-29D1ARTZR71 ADM6315-26D1ARTRL7 ADM6315-26D1ART-RL ADM6315-26D1ARTZR71 ADM6315-26D1ARTZRL1 ADM6315-46D2ARTRL7 ADM6315-46D2ART-RL ADM6315-46D2ARTZR71 ADM6315-45D2ARTRL7 ADM6315-45D2ART-RL ADM6315-45D2ARTZR71 ADM6315-44D2ARTRL7 ADM6315-44D2ART-RL ADM6315-44D2ARTZR71 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C –40°C to +125°C –40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] Rev. E | Page 8 of 12 Package Option RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 Trip Point 4.63 4.63 4.63 4.50 4.50 4.50 4.39 4.39 3.08 3.08 3.08 3.08 2.93 2.93 2.93 2.63 2.63 2.63 2.63 4.63 4.63 4.63 4.50 4.50 4.50 4.39 4.39 4.39 Minimum Timeout (ms) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 20 20 20 20 20 20 20 20 20 Branding MDV MDV M9Q MDU MDU M81 MDT MDT MDG MDG M7X M7X MDC MDC M7T MDB MDB MDB# MDB# MEV MEV M83 MEU MEU MA8 MET MET M80 ADM6315 Model ADM6315-31D2ARTRL7 ADM6315-31D2ART-RL ADM6315-31D2ARTZR71 ADM6315-31D2ARTZRL1 ADM6315-29D2ARTRL7 ADM6315-29D2ART-RL ADM6315-29D2ARTZR71 ADM6315-26D2ARTRL7 ADM6315-26D2ART-RL ADM6315-26D2ARTZR71 ADM6315-26D2ARTZRL1 ADM6315-46D3ARTRL7 ADM6315-46D3ART-RL ADM6315-46D3ARTZR71 ADM6315-45D3ARTRL7 ADM6315-45D3ART-RL ADM6315-45D3ARTZR71 ADM6315-44D3ARTRL7 ADM6315-44D3ART-RL ADM6315-44D3ARTZR71 ADM6315-44D3ARTZRL1 ADM6315-31D3ARTRL7 ADM6315-31D3ART-RL ADM6315-31D3ARTZR71 ADM6315-31D3ARTZRL1 ADM6315-29D3ARTRL7 ADM6315-29D3ART-RL ADM6315-29D3ARTZR71 ADM6315-26D3ARTRL7 ADM6315-26D3ART-RL ADM6315-26D3ARTZR71 ADM6315-26D3ARTZRL1 ADM6315-46D4ARTRL7 ADM6315-46D4ART-RL ADM6315-46D4ARTZR71 ADM6315-45D4ARTRL7 ADM6315-45D4ART-RL ADM6315-44D4ARTRL7 ADM6315-44D4ART-RL ADM6315-44D4ARTZRL1 ADM6315-44D4ARTZRL1 ADM6315-31D4ARTRL7 ADM6315-31D4ART-RL ADM6315-31D4ARTZR71 ADM6315-29D4ARTRL7 ADM6315-29D4ART-RL ADM6315-29D4ARTZR71 ADM6315-26D4ARTRL7 ADM6315-26D4ART-RL ADM6315-26D4ARTZR71 ADM6315-26D4ARTZRL1 1 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C –40°C to +125°C −40°C to +125°C –40°C to +125°C Package Description 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] 4-Lead Small Outline Transistor [SOT-143] Z = RoHS-Compliant Part, # denotes lead-free product may be top or bottom marked. Rev. E | Page 9 of 12 Package Option RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 RA-4 Trip Point 3.08 3.08 3.08 3.08 2.93 2.93 2.93 2.63 2.63 2.63 2.63 4.63 4.63 4.63 4.50 4.50 4.50 4.39 4.39 4.39 4.39 3.08 3.08 3.08 3.08 2.93 2.93 2.93 2.63 2.63 2.63 2.63 4.63 4.63 4.63 4.50 4.50 4.39 4.39 4.39 4.39 3.08 3.08 3.08 2.93 2.93 2.93 2.63 2.63 2.63 2.63 Minimum Timeout (ms) 20 20 20 20 20 20 20 20 20 20 20 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 140 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 1120 Branding MEG MEG M7Y M7Y MEC MEC M7U MEB MEB MEB# MEB# MFV MFV M84 MFU MFU M82 MFT MFT MFT# MFT# MFG MFG M4G M4G MFC MFC M7V MFB MFB MFB# MFB# MGV MGV M85 MGU MGU MGT MGT M9H M9H MGG MGG M7Z MGC MGC M7W MGB MGB MGB# MGB# ADM6315 NOTES Rev. E | Page 10 of 12 ADM6315 NOTES Rev. E | Page 11 of 12 ADM6315 NOTES ©1999–2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00081-0-9/07(E) Rev. E | Page 12 of 12