AD ADM6328-30ARTZ-R7

Ultralow Power, 3-Lead, SOT-23
Microprocessor Reset Circuits
ADM6326/ADM6328/ADM6346/ADM6348
FEATURES
APPLICATIONS
Telecommunications
Microprocessor systems
Desktop and notebook computers
Portable equipment
FUNCTIONAL BLOCK DIAGRAMS
ADM6326/ADM6346
VCC
RESET
08052-001
RESET
GENERATOR
(100ms)
VREF
GND
Figure 1.
ADM6328/ADM6348
VCC
RESET
GENERATOR
(100ms)
VREF
GND
RESET
08052-002
Ultralow supply current of 1 μA maximum (ADM6326/ADM6328)
Accurate monitoring of 2.5 V, 3 V, 3.3 V, and 5 V rails
Reset thresholds available in increments from 2.2 V to 4.63 V
Glitch immunity from negative-going VCC transients
2 reset output options
Push-pull RESET (ADM6326/ADM6346)
Open-drain RESET (ADM6328/ADM6348)
Minimum reset timeout of 100 ms
Operating temperature range of −40°C to +85°C
3-lead SOT-23 package
Figure 2.
GENERAL DESCRIPTION
The ADM6326/ADM6328/ADM6346/ADM6348 devices provide
low cost solutions for protecting sensitive circuitry, such as microprocessor and telecommunications circuitry.
With built-in glitch immunity, ultralow supply currents, and
24 reset threshold voltage options, the ADM6326/ADM6328/
ADM6346/ADM6348 not only ensure that systems are immune
to fast transients on VCC, but also that the devices are suitable
for monitoring a variety of supply voltages in low power,
portable equipment.
These devices provide a reset output during power-up, powerdown, and brownout conditions. On power-up, an internal
timer holds RESET asserted for at least 100 ms. This holds the
microprocessor in a reset state until conditions have stabilized.
The reset output remains operational with VCC as low as 1 V.
The ADM6326 and ADM6346 have an active low push-pull reset
output. The ADM6328 and ADM6348 have an active low opendrain reset output, which requires an external pull-up resistor.
The ADM6326 and ADM6328 offer a choice of ten reset thresholds
in increments between 2.2 V and 3.08 V, whereas the ADM6346
and ADM6348 offer a choice of 14 reset thresholds between 3.3 V
and 4.63 V.
These devices are available in a 3-lead SOT-23 package and
operate over the extended temperature range of −40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
ADM6326/ADM6328/ADM6346/ADM6348
TABLE OF CONTENTS
Features .............................................................................................. 1 Pin Configuration and Function Descriptions..............................5 Applications ....................................................................................... 1 Typical Performance Characteristics ..............................................6 Functional Block Diagrams ............................................................. 1 Theory of Operation .........................................................................7 General Description ......................................................................... 1 Reset Output ..................................................................................7 Revision History ............................................................................... 2 Interfacing to Other Devices .......................................................7 Specifications..................................................................................... 3 Transient Immunity ......................................................................7 Absolute Maximum Ratings............................................................ 4 Outline Dimensions ..........................................................................8 Thermal Resistance ...................................................................... 4 Ordering Guide .............................................................................9 ESD Caution .................................................................................. 4 REVISION HISTORY
9/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
ADM6326/ADM6328/ADM6346/ADM6348
SPECIFICATIONS
TA = −40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C and VCC = 3 V. Overtemperature limits are guaranteed by design.
Table 1.
Parameter
OPERATING VOLTAGE RANGE, VCC
INPUT CURRENT, ICC
RESET THRESHOLD
Threshold Voltage, VTH (See Table 2)
Temperature Coefficient
Hysteresis
ADM6326/ADM6328
ADM6346/ADM6348
TIMING CHARACTERISTICS
VCC to Reset Delay (tRD)
Reset Active Timeout Period (tRP)
RESET OUTPUT VOLTAGE LOW, VOL
Min
1.0
Typ
VTH − 2.5%
VTH − 1.5%
0.5
Max
5.5
1.0
Unit
V
μA
1.0
1.75
μA
VTH
VTH
40
VTH + 2.5%
VTH + 1.5%
V
V
ppm/°C
6.3
9.5
ADM6326/ADM6328 only, VCC = 3.0 V for VTH ≤
2.93 V, VCC = 3.2 V for VTH > 2.93 V, no load
VCC = 5.5 V, no load
TA = 25°C
mV
mV
20
185
μs
ms
V
VCC = VTH to (VTH − 100 mV)
0.8 × VCC
V
V
VCC ≥ 1.2 V, ISINK = 100 μA, reset asserted
ADM6326 only, VCC = 3.2 V, ISOURCE = 500 μA
0.8 × VCC
V
0.8 × VCC
V
ADM6326/ADM6346 only, VCC = 4.5 V,
ISOURCE = 800 μA, VTH ≤ 4.38 V
ADM6326/ADM6346 only, VCC = VTH(MAX),
ISOURCE = 800 μA, VTH ≥ 4.5 V
100
280
0.3
0.4
RESET OUTPUT VOLTAGE HIGH, VOH
Test Conditions/Comments
OPEN-DRAIN RESET OUTPUT LEAKAGE CURRENT
0.1
VCC > 2.1 V, ISINK = 1.6 mA, reset asserted
μA
Table 2. Reset Threshold Voltage
TA = −40°C to +85°C
TA = 25°C
Parameter
Min
Typ
Max
Min
Max
Unit
RESET THRESHOLD VOLTAGE (VTH)
ADM632x-22
ADM632x-23
ADM632x-24
ADM632x-25
ADM632x-26
ADM632x-27
ADM632x-28
ADM632x-29
ADM632x-30
ADM632x-31
ADM634x-33
ADM634x-34
ADM634x-35
ADM634x-36
ADM634x-37
ADM634x-38
ADM634x-39
ADM634x-40
ADM634x-41
ADM634x-42
ADM634x-43
ADM634x-44
ADM634x-45
ADM634x-46
2.167
2.285
2.364
2.462
2.591
2.66
2.758
2.886
2.955
3.034
3.25
3.349
3.447
3.546
3.644
3.743
3.841
3.94
4.038
4.137
4.235
4.314
4.432
4.56
2.2
2.32
2.4
2.5
2.63
2.7
2.8
2.93
3.00
3.08
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.38
4.5
4.63
2.233
2.355
2.436
2.537
2.669
2.741
2.842
2.974
3.045
3.126
3.35
3.451
3.552
3.654
3.755
3.857
3.958
4.06
4.161
4.263
4.364
4.446
4.567
4.699
2.145
2.262
2.34
2.437
2.564
2.633
2.73
2.857
2.925
3.003
3.217
3.315
3.412
3.51
3.607
3.705
3.802
3.9
3.997
4.095
4.192
4.27
4.387
4.514
2.25
2.375
2.46
2.562
2.696
2.768
2.87
3.0
3.075
3.15
3.383
3.485
3.587
3.69
3.792
3.895
3.997
4.1
4.202
4.305
4.407
4.489
4.612
4.746
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Rev. 0 | Page 3 of 12
ADM6326/ADM6328/ADM6346/ADM6348
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 3.
Parameter
Supply Voltage, VCC
Input Current, ICC
Output Voltage
Push-Pull RESET
Open-Drain RESET
Output Current (RESET)
Rate of Rise of VCC
Temperature
Storage
Operating
Soldering (10 sec)
Rating
−0.3 V to +6 V
20 mA
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
−0.3 V to (VCC + 0.3 V)
−0.3 V to +6 V
20 mA
Package Type
3-Lead SOT-23
Table 4. Thermal Resistance
ESD CAUTION
100 V/μs
−65°C to +155°C
−40°C to +85°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 4 of 12
θJA
270
Unit
°C/W
ADM6326/ADM6328/ADM6346/ADM6348
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
RESET 2
ADM6326/
ADM6328/
ADM6346/
ADM6348
3
TOP VIEW
(Not to Scale)
VCC
08052-003
GND
Figure 3. ADM6326/ADM6328/ADM6346/ADM6348 Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
Mnemonic
GND
RESET
3
VCC
Description
Ground Reference for All Signals; 0 V.
Active Low Logic Output. This pin is low when VCC is less than the reset threshold; it remains low for 185 ms
(typical) after VCC becomes greater than the reset threshold.
Supply Voltage Being Monitored.
Rev. 0 | Page 5 of 12
ADM6326/ADM6328/ADM6346/ADM6348
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
280
0.9
0.8
0.7
0.6
0.5
VCC = 1.4V
0.4
0.3
0.2
220
200
180
160
140
0
20
40
60
80
TEMPERATURE (°C)
100
–40
08052-004
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 4. Supply Current vs. Temperature
Figure 6. Power-Up Reset Timeout vs. Temperature
800
250
700
POWER-DOWN RESET DELAY (µs)
MAXIMUM TRANSIENT DURATION (µs)
–20
08052-007
120
0.1
0
–40
240
600
500
400
300
200
200
150
100
VOD = 10mV
VOD = 20mV
50
VOD = 200mV
100
0
10
100
RESET THRESHOLD OVERDRIVE, VTH – VCC (mV)
1000
0
–40
08052-006
1
–20
0
20
VOD = 100mV
40
60
TEMPERATURE (°C)
Figure 7. Power-Down Reset Delay vs. Temperature
Figure 5. Maximum Transient Duration vs. Reset Threshold Overdrive
Rev. 0 | Page 6 of 12
80
08052-005
SUPPLY CURRENT (µA)
POWER-UP RESET TIMEOUT (ms)
260
VCC = 5V
VCC = 3.3V
ADM6326/ADM6328/ADM6346/ADM6348
THEORY OF OPERATION
RESET OUTPUT
The ADM6326 and ADM6346 have an active low, push-pull
reset output, whereas the ADM6328 and ADM6348 have an
active low, open-drain reset output, which requires an external
pull-up resistor. The RESET signal is guaranteed to be valid for
VCC down to 1 V.
When the ADM6326/ADM6328/ADM6346/ADM6348 are
powered up, the RESET output remains low for a period typically
equal to the RESET active timeout period of 185 ms. This feature
allows adequate time for the system to power up correctly and
for the power supply to stabilize before any devices are brought out
of reset and are allowed to begin executing instructions. Initializing
a system in this way provides a more reliable startup for microprocessor systems.
When the monitored voltage falls below its associated threshold
(VTH), RESET is asserted within 20 μs (typical). Asserting RESET
this quickly means that the entire system can be reset at once
before any part of the system’s voltage falls below its recommended
operating voltage. This system reset can avoid dangerous and/or
erroneous operation of a microprocessor based system.
VCC
INTERFACING TO OTHER DEVICES
The active low, open-drain reset output of the ADM6328 and
ADM6348 makes these devices ideal for integration with devices
such as microprocessors with bidirectional reset pins. Simply
connect the RESET output of the ADM6328 or ADM6348 to
the RESET input of the microprocessor using a single pull-up
resistor to allow either device to initiate a system reset (see
Figure 8).
VCC
VCC
MICROPROCESSOR
SYSTEM
ADM6328/ADM6348
RESET
INPUT
RESET
GND
GND
Figure 8. Interfacing to a Microprocessor with a Bidirectional Reset Pin
TRANSIENT IMMUNITY
To avoid unnecessary resets caused by fast power supply transients,
the ADM6326/ADM6328/ADM6346/ADM6348 provide glitch
immunity from negative-going VCC transients.
Figure 5 shows the RESET comparator overdrive (that is, the
maximum magnitude of negative-going pulses with respect to
the typical threshold) vs. the pulse duration without a reset.
VTH
VTH
VCC
1V
0V
tRP
tRD
0V
Figure 9. RESET Timing
Rev. 0 | Page 7 of 12
08052-009
VCC
RESET
VCC
RPULL-UP
08052-008
The ADM6326/ADM6328/ADM6346/ADM6348 are designed
to protect the integrity of a system’s operation by ensuring the
proper operation of the system during power-up, power-down,
and brownout conditions. Ultralow supply currents make these
devices particularly suitable for use in low power, portable
equipment.
ADM6326/ADM6328/ADM6346/ADM6348
OUTLINE DIMENSIONS
3.04
2.90
2.80
1.40
1.30
1.20
3
1
2
0.60
0.45
2.05
1.78
1.03
0.89
1.12
0.89
0.100
0.013
SEATING
PLANE
GAUGE
PLANE
0.54
REF
0.180
0.085
0.51
0.37
0.25
0.60 MAX
0.30 MIN
COMPLIANT TO JEDEC STANDARDS TO-236-AB
Figure 10. 3-Lead Small Outline Transistor Package [SOT-23-3]
(RT-3)
Dimensions shown in millimeters
Rev. 0 | Page 8 of 12
011909-C
1.02
0.95
0.88
2.64
2.10
ADM6326/ADM6328/ADM6346/ADM6348
ORDERING GUIDE
Model 1
ADM6326-22ARTZ-R7 2, 3
ADM6326-23ARTZ-R72
ADM6326-24ARTZ-R72
ADM6326-25ARTZ-R72
ADM6326-26ARTZ-R72
ADM6326-27ARTZ-R72
ADM6326-28ARTZ-R72
ADM6326-29ARTZ-R72
ADM6326-30ARTZ-R72
ADM6326-31ARTZ-R72
ADM6328-22ARTZ-R72
ADM6328-23ARTZ-R72
ADM6328-24ARTZ-R72
ADM6328-25ARTZ-R72
ADM6328-26ARTZ-R72
ADM6328-27ARTZ-R72
ADM6328-28ARTZ-R72, 3
ADM6328-29ARTZ-R72
ADM6328-30ARTZ-R72
ADM6328-31ARTZ-R72
ADM6346-33ARTZ-R72, 3
ADM6346-34ARTZ-R72
ADM6346-35ARTZ-R72
ADM6346-36ARTZ-R72
ADM6346-37ARTZ-R72
ADM6346-38ARTZ-R72
ADM6346-39ARTZ-R72
ADM6346-40ARTZ-R72
ADM6346-41ARTZ-R72
ADM6346-42ARTZ-R72
ADM6346-43ARTZ-R72
ADM6346-44ARTZ-R72
ADM6346-45ARTZ-R72
ADM6346-46ARTZ-R72
ADM6348-33ARTZ-R72
ADM6348-34ARTZ-R72
ADM6348-35ARTZ-R72
ADM6348-36ARTZ-R72
ADM6348-37ARTZ-R72
ADM6348-38ARTZ-R72
ADM6348-39ARTZ-R72
ADM6348-40ARTZ-R72
ADM6348-41ARTZ-R72
ADM6348-42ARTZ-R72
ADM6348-43ARTZ-R72
ADM6348-44ARTZ-R72
ADM6348-45ARTZ-R72
ADM6348-46ARTZ-R72, 3
Typical Threshold
Voltage (TA = 25°C)
2.2 V
2.32 V
2.4 V
2.5 V
2.63 V
2.7 V
2.8 V
2.93 V
3.0 V
3.08 V
2.2 V
2.32 V
2.4 V
2.5 V
2.63 V
2.7 V
2.8 V
2.93 V
3.0 V
3.08 V
3.3 V
3.4 V
3.5 V
3.6 V
3.7 V
3.8 V
3.9 V
3.0 V
4.1 V
4.2 V
4.3 V
4.38 V
4.5 V
4.63 V
3.3 V
3.4 V
3.5 V
3.6 V
3.7 V
3.8 V
3.9 V
3.0 V
4.1 V
4.2 V
4.3 V
4.38 V
4.5 V
4.63 V
RESET Output
Structure
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Push-Pull
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Open-Drain
Package Description
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
1
Contact sales for the availability of nonstandard models.
Z = RoHS Compliant Part.
3
Standard model.
2
`
Rev. 0 | Page 9 of 12
Package Option
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
RT-3
Branding
LAQ
LAR
LAS
LAT
LAU
LAV
LAW
LAX
LAY
LAZ
LB0
LB1
LB2
LB3
LB4
LB5
LB6
LB7
LB8
LB9
LBA
LBC
LBD
LBE
LBF
LBG
LBH
LCN
LCP
LCQ
LCR
LCS
LCT
LCU
LCV
LCW
LCX
LCY
LCZ
LD0
LD1
LD2
LD3
LD4
LD5
LD6
LD7
LD8
ADM6326/ADM6328/ADM6346/ADM6348
NOTES
Rev. 0 | Page 10 of 12
ADM6326/ADM6328/ADM6346/ADM6348
NOTES
Rev. 0 | Page 11 of 12
ADM6326/ADM6328/ADM6346/ADM6348
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08052-0-9/09(0)
Rev. 0 | Page 12 of 12