AD AD9396KSTZ-150

Analog/DVI
Dual-Display Interface
AD9396
FEATURES
Advanced TVs
HDTVs
Projectors
LCD monitors
ANALOG INTERFACE
R/G/B OR YPbPrIN1
2:1
MUX
HSYNC 0
HSYNC 1
HSYNC 0
HSYNC 1
2:1
MUX
SOGIN 0
SOGIN 1
2:1
MUX
COAST
FILT
CKINV
CKEXT
2:1
MUX
R/G/B 8 × 3
A/D
CLAMP
SYNC
PROCESSING
AND
CLOCK
GENERATION
OR YCbCr
2 DATACK
HSOUT
VSOUT
SOGOUT
REFOUT
REFIN
REF
SCL
SERIAL REGISTER
AND
POWER MANAGEMENT
RGB
SDA
YCbCr MATRIX
R/G/B OR YPbPrIN0
YCbCr (4:2:2
OR 4:4:4)
2
DATACK
HSOUT
VSOUT
SOGOUT
DE
DIGITAL INTERFACE
R/G/B 8 × 3
OR YCbCr
Rx0+
Rx0–
2
Rx1+
Rx1–
Rx2+
R/G/B 8 × 3
DATACK
DE
HSYNC
DVI RECEIVER
VSYNC
Rx2–
RxC+
RxC–
RTERM
MCL
MDA
HDCP
DDCSCL
DDCSDA
AD9396
05690-001
APPLICATIONS
FUNCTIONAL BLOCK DIAGRAM
MUXES
Analog/DVI dual interface
Supports high bandwidth digital content protection
RGB-to-YCbCr 2-way color conversion
Automated clamping level adjustment
1.8 V/3.3 V power supply
100-lead, Pb-free LQFP
RGB and YCbCr output formats
Analog interface
8-bit triple ADC
150 MSPS maximum conversion rate
Macrovision® detection
2:1 input mux
Full sync processing
Sync detect for hot plugging
Midscale clamping
Digital video interface
DVI 1.0
150 MHz DVI receiver
Supports HDCP 1.1
Figure 1.
GENERAL DESCRIPTION
The AD9396 offers designers the flexibility of an analog
interface and digital visual interface (DVI) receiver integrated
on a single chip. Also included is support for high bandwidth
digital content protection (HDCP).
clock output frequencies range from 12 MHz to 150 MHz. PLL
clock jitter is typically less than 700 ps p-p at 150 MHz. The
AD9396 also offers full sync processing for composite sync and
sync-on-green (SOG) applications.
The AD9396 is a complete 8-bit, 150 MSPS monolithic analog
interface optimized for capturing component video (YPbPr)
and RGB graphics signals. Its 150 MSPS encode rate capability
and full power analog bandwidth of 330 MHz supports all
HDTV formats (up to 1080p and 720p) and FPD resolutions up
to SXGA (1280 × 1024 @ 80 Hz).
The AD9396 contains a DVI-compatible receiver and supports
all HDTV formats (up to 1080p and 720p) and display
resolutions up to SXGA (1280 × 1024 @ 80 Hz). The receiver
features an intrapair skew tolerance of up to one full clock cycle.
With the inclusion of HDCP, displays may now receive
encrypted video content. The AD9396 allows for authentication
of a video receiver, decryption of encoded data at the receiver,
and renewability of that authentication during transmission as
specified by the HDCP 1.1 protocol.
The analog interface includes a 150 MHz triple ADC with
internal 1.25 V reference, a phase-locked loop (PLL), programmable gain, offset, and clamp control. The user provides only
1.8 V and 3.3 V power supply, analog input, and HSYNC.
Three-state CMOS outputs may be powered from 1.8 V to 3.3V.
The on-chip PLL generates a pixel clock from HSYNC. Pixel
Fabricated in an advanced CMOS process, the AD9396 is provided in a space-saving, 100-lead, surface-mount, Pb-free plastic
LQFP and is specified over the 0ºC to 70ºC temperature range.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
AD9396
TABLE OF CONTENTS
Features .............................................................................................. 1
2-Wire Serial Register Map ........................................................... 21
Applications....................................................................................... 1
2-Wire Serial Control Register Details ........................................ 29
Functional Block Diagram .............................................................. 1
Chip Identification ..................................................................... 29
General Description ......................................................................... 1
PLL Divider Control .................................................................. 29
Specifications..................................................................................... 3
Clock Generator Control .......................................................... 29
Analog Interface Electrical Characteristics............................... 3
Input Gain ................................................................................... 30
Digital Interface Electrical Characteristics ............................... 4
Input Offset ................................................................................. 30
Absolute Maximum Ratings............................................................ 6
Sync .............................................................................................. 30
Explanation of Test Levels ........................................................... 6
Coast and Clamp Controls........................................................ 31
ESD Caution.................................................................................. 6
Status of Detected Signals ......................................................... 31
Pin Configuration and Function Descriptions............................. 7
Polarity Status ............................................................................. 32
Design Guide................................................................................... 11
BT656 Generation ...................................................................... 36
General Description................................................................... 11
Macrovision................................................................................. 36
Digital Inputs .............................................................................. 11
Color Space Conversion ............................................................ 37
Analog Input Signal Handling.................................................. 11
2-Wire Serial Control Port ............................................................ 39
HSYNC and VSYNC Inputs...................................................... 11
PCB Layout Recommendations.................................................... 41
Serial Control Port ..................................................................... 11
Analog Interface Inputs ............................................................. 41
Output Signal Handling............................................................. 11
Power Supply Bypassing ............................................................ 41
Clamping ..................................................................................... 11
PLL ............................................................................................... 41
Timing.......................................................................................... 15
Outputs (Both Data and Clocks).............................................. 42
DVI Receiver............................................................................... 19
Digital Inputs .............................................................................. 42
DE Generator .............................................................................. 19
Color Space Converter (CSC) Common Settings...................... 43
4:4:4 to 4:2:2 Filter ...................................................................... 19
Outline Dimensions ....................................................................... 45
Timing Diagrams........................................................................ 20
Ordering Guide .......................................................................... 45
REVISION HISTORY
10/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 48
AD9396
SPECIFICATIONS
ANALOG INTERFACE ELECTRICAL CHARACTERISTICS
VDD, VD = 3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum.
Table 1.
Parameter
RESOLUTION
DC ACCURACY
Differential Nonlinearity
Integral Nonlinearity
No Missing Codes
ANALOG INPUT
Input Voltage Range
Minimum
Maximum
Gain Tempco
Input Bias Current
Input Full-Scale Matching
Offset Adjustment Range
SWITCHING PERFORMANCE 1
Maximum Conversion Rate
Minimum Conversion Rate
Data to Clock Skew
SERIAL PORT TIMING
tBUFF
tSTAH
tDHO
tDAL
tDAH
tDSU
tSTASU
tSTOSU
HSYNC Input Frequency
Maximum PLL Clock Rate
Minimum PLL Clock Rate
PLL Jitter
Sampling Phase Tempco
DIGITAL INPUTS (5 V Tolerant)
Input Voltage, High (VIH)
Input Voltage, Low (VIL)
Input Current, High (IIH)
Input Current, Low (IIL)
Input Capacitance
DIGITAL OUTPUTS
Output Voltage, High (VOH)
Output Voltage, Low (VOL)
Duty Cycle, DATACK
Output Coding
Min
AD9396KSTZ-100
Typ
Max
8
Temp
Test Level
25°C
25°C
Full
I
I
Full
Full
25°C
25°C
25C
Full
Full
VI
VI
V
V
VI
VI
V
Full
Full
Full
VI
VI
IV
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
25°C
Full
VI
VI
VI
VI
VI
VI
VI
VI
VI
VI
IV
IV
IV
4.7
4.0
0
4.7
4.0
250
4.7
4.0
15
100
Full
Full
Full
Full
25°C
VI
VI
V
V
V
2.6
Full
Full
Full
VI
VI
V
VDD − 0.1
Min
AD9396KSTZ-150
Typ
Max
8
–0.6
+1.6/–1.0
±1.0
±2.1
Guaranteed
±0.7
+1.8/–1.0
±1.1
±2.25
Guaranteed
0.5
1.0
0.5
1.0
100
0.2
1.25
1.50
50
220
1
1.25
1.50
50
5
7
100
150
10
+2.0
−0.5
110
10
+2.0
−0.5
4.7
4.0
0
4.7
4.0
250
4.7
4.0
15
150
110
12
12
700
15
700
15
2.6
0.8
0.8
−82
82
3
45
5
7
−82
82
3
VDD − 0.1
50
Binary
Rev. 0 | Page 3 of 48
0.4
55
45
50
Binary
0.4
55
Unit
Bits
LSB
LSB
V p–p
V p–p
ppm/°C
μA
%FS
%FS
%FS
MSPS
MSPS
ns
μs
μs
μs
μs
μs
ns
μs
μs
KHz
MHz
MHz
ps p-p
ps/°C
V
V
μA
μA
pF
V
V
%
AD9396
Parameter
POWER SUPPLY
VD Supply Voltage
DVDD Supply Voltage
VDD Supply Voltage
PVDD Supply Voltage
ID Supply Current (VD)
IDVDD Supply Current (DVDD)
IDD Supply Current (VDD) 2
IPVDD Supply Current (PVDD)
Total Power
Power-Down Dissipation
DYNAMIC PERFORMANCE
Analog Bandwidth, Full
Power
Signal-to-Noise Ratio (SNR)
Without Harmonics
fIN = 40.7 MHz
Crosstalk
THERMAL CHARACTERISTICS
θJA Junction-to-Ambient
1
2
3
AD9396KSTZ-100
Typ
Max
Test Level
Min
Full
Full
Full
Full
25°C
25°C
25°C
25°C
Full
Full
IV
IV
IV
IV
VI
VI
VI
VI
VI
VI
3.15
1.7
1.7
1.7
25°C
V
330
330
MHz
25°C
I
46
46
dB
Full
Full
V
V
45
60
45
60
dB
dBc
V
35
35
°C/W
3.3
1.8
3.3
1.8
260
45
37
10
1.1
130
3.47
1.9
3.47
1.9
300
60
100 3
15
1.4
Min
AD9396KSTZ-150
Typ
Max
Temp
3.15
1.7
1.7
1.7
3.3
1.8
3.3
1.8
Unit
3.47
1.9
3.47
1.9
330
85
1303
20
1.4
1.15
130
V
V
V
V
mA
mA
mA
mA
W
mW
Drive strength = high.
DATACK load = 15 pF, data load = 5 pF.
Specified current and power values with a worst-case pattern (on/off).
DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS
VDD = VD = 3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum.
Table 2.
AD9396KSTZ-100
Parameter
RESOLUTION
DC DIGITAL I/O Specifications
High Level Input Voltage, (VIH)
Low Level Input Voltage, (VIL)
High Level Output Voltage, (VOH)
Low Level Output Voltage, (VOL)
DC SPECIFICATIONS
Output High Level
(IOHD) (VOUT = VOH)
Output Low Level
IOLD, (VOUT = VOL)
DATACK High Level
VOHC, (VOUT = VOH)
DATACK Low Level
VOLC, (VOUT = VOL)
Differential Input Voltage, SingleEnded Amplitude
Test
Level
Conditions
VI
VI
VI
VI
IV
IV
IV
IV
IV
IV
IV
IV
IV
Min
Typ
8
Max
2.5
Typ
8
Max
Unit
Bit
0.8
0.8
0.1
0.1
V
V
V
V
700
mA
mA
mA
mA
mA
mA
mA
mA
mV
36
24
12
8
40
20
30
15
75
Rev. 0 | Page 4 of 48
Min
2.5
VDD − 0.1
VDD − 0.1
Output drive = high
Output drive = low
Output drive = high
Output drive = low
Output drive = high
Output drive = low
Output drive = high
Output drive = low
AD9396KSTZ-150
36
24
12
8
40
20
30
15
700
75
AD9396
AD9396KSTZ-100
Parameter
POWER SUPPLY
VD Supply Voltage
VDD Supply Voltage
DVDD Supply Voltage
PVDD Supply Voltage
IVD Supply Current (Typical Pattern) 1
IVDD Supply Current (Typical Pattern) 2
IDVDD Supply Current (Typical Pattern)1, 4
IPVDD Supply Current (Typical Pattern)1
Power-Down Supply Current (IPD)
AC SPECIFICATIONS
Intrapair (+ to −) Differential Input Skew
(TDPS)
Channel-to-Channel Differential Input
Skew (TCCS)
Low-to-High Transition Time for Data and
Controls (DLHT)
Test
Level
Min
Typ
Max
Min
Typ
Max
Unit
3.15
1.7
1.7
1.7
3.3
3.3
1.8
1.8
80
40
88
26
130
3.47
347
1.9
1.9
100
100 3
110
35
3.15
1.7
1.7
1.7
3.3
3.3
1.8
1.8
80
55
110
30
130
3.47
347
1.9
1.9
110
1753
145
40
V
V
V
V
mA
mA
mA
mA
mA
IV
360
ps
IV
6
900
Clock
Period
ps
1300
ps
650
ps
1200
ps
850
ps
1250
ps
800
ps
1200
ps
2.0
55
150
ns
%
MHz
IV
IV
IV
IV
V
V
V
V
VI
IV
IV
Low-to-High Transition Time for
DATACK (DLHT)
IV
IV
High-to-Low Transition Time for Data and
Controls (DHLT)
IV
IV
High-to-Low Transition Time for
DATACK (DHLT)
IV
IV
Clock to Data Skew 5 (TSKEW)
Duty Cycle, DATACK5
DATACK Frequency (FCIP)
Conditions
AD9396KSTZ-150
Output drive = high;
CL = 10 pF
Output drive = low;
CL = 5 pF
Output drive = high;
CL = 10 pF
Output drive = low;
CL = 5 pF
Output drive = high;
CL = 10 pF
Output drive = low;
CL = 5 pF
Output drive = high;
CL = 10 pF
Output drive = low;
CL = 5 pF
IV
IV
VI
–0.5
45
20
1
+2.0
50
The typical pattern contains a gray scale area, output drive = high. Worst-case pattern is alternating black and white pixels.
The typical pattern contains a gray scale area, output drive = high.
Specified current and power values with a worst-case pattern (on/off).
4
DATACK load = 10 pF, data load = 5 pF.
5
Drive strength = high.
2
3
Rev. 0 | Page 5 of 48
–0.5
AD9396
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VD
VDD
DVDD
PVDD
Analog Inputs
Digital Inputs
Digital Output Current
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Maximum Case Temperature
Rating
3.6 V
3.6 V
1.98 V
1.98 V
VD to 0.0 V
5 V to 0.0 V
20 mA
−25°C to +85°C
−65°C to +150°C
150°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
EXPLANATION OF TEST LEVELS
Table 4.
Level
I
II
III
IV
V
VI
Test
100% production tested.
100% production tested at 25°C and sample
tested at specified temperatures.
Sample tested only.
Parameter is guaranteed by design and
characterization testing.
Parameter is a typical value only.
100% production tested at 25°C; guaranteed by
design and characterization testing.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 48
AD9396
VDD
RED 0
RED 1
RED 2
RED 3
RED 4
RED 5
RED 6
RED 7
GND
VDD
DATACK
DE
HSOUT
SOGOUT
VSOUT
O/E FIELD
SDA
SCL
PWRDN
VD
RAIN0
GND
RAIN1
VD
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
GND
74
GAIN0
3
73
SOGIN 0
GREEN 5
4
72
VD
GREEN 4
5
71
GAIN1
GREEN 3
6
70
SOGIN 1
GREEN 2
7
69
GND
GREEN 1
8
68
BAIN0
GREEN 0
9
67
VD
VDD
10
AD9396
66
BAIN1
GND
11
65
GND
BLUE 7
12
TOP VIEW
(Not to Scale)
64
HSYNC 0
BLUE 6
13
63
HSYNC 1
BLUE 5
14
62
EXTCLK/COAST
BLUE 4
15
61
VSYNC 0
BLUE 3
16
60
VSYNC 1
BLUE 2
17
59
PVDD
BLUE 1
18
58
PGND
BLUE 0
19
57
FILT
NC
20
56
PVDD
NC
21
55
PGND
NC
22
54
PVDD
NC
23
53
GND
CTL3
24
52
MDA
CTL2
25
51
MCL
41
42
43
44
45
46
47
48
49
50
GND
RxC+
RxC–
VD
RTERM
GND
DVDD
DDCSCL
DDCSDA
36
GND
Rx2+
35
Rx0+
40
34
Rx0–
Rx2–
33
VD
39
32
DVDD
GND
31
GND
38
30
DVDD
Rx1+
29
GND
37
28
NC
Rx1–
27
NC = NO CONNECT
26
GREEN 6
PIN 1
CTL0
2
CTL1
1
05690-002
75
GND
GREEN 7
Figure 2. Pin Configuration
Table 5. Complete Pinout List
Pin Type
INPUTS
OUTPUTS
Pin No.
79
77
74
71
68
66
64
63
61
60
73
70
62
62
81
92 to 99
2 to 9
12 to 19
Mnemonic
RAIN0
RAIN1
GAIN0
GAIN1
BAIN0
BAIN1
HSYNC 0
HSYNC 1
VSYNC 0
VSYNC 1
SOGIN 0
SOGIN 1
EXTCLK
COAST
PWRDN
RED [7:0]
GREEN [7:0]
BLUE [7:0]
B
B
Function
Analog Input for Converter R Channel 0
Analog Input for Converter R Channel 1
Analog Input for Converter G Channel 0
Analog Input for Converter G Channel 1
Analog Input for Converter B Channel 0
Analog Input for Converter B Channel 1
Horizontal SYNC Input for Channel 0
Horizontal SYNC Input for Channel 1
Vertical SYNC Input for Channel 0
Vertical SYNC Input for Channel 1
Input for Sync-on-Green Channel 0
Input for Sync-on-Green Channel 1
External Clock Input—Shares Pin with COAST
PLL COAST Signal Input—Shares Pin with EXTCLK
Power-Down Control
Outputs of Red Converter, Bit 7 is MSB
Outputs of Green Converter, Bit 7 is MSB
Outputs of Blue Converter, Bit 7 is MSB
Rev. 0 | Page 7 of 48
Value
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
0.0 V to 1.0 V
0.0 V to 1.0 V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
VDD
VDD
VDD
AD9396
Pin Type
OUTPUTS
Pin No.
89
87
85
86
84
24, 25, 26, 27
57
80, 76, 72,
67, 45, 33
100, 90, 10
59, 56, 54
48, 32, 30
REFERENCES
POWER SUPPLY
CONTROL
HDCP
DIGITAL VIDEO DATA
DIGITAL VIDEO CLOCK
INPUTS
DATA ENABLE
RTERM
Mnemonic
DATACK
HSOUT
VSOUT
SOGOUT
O/E FIELD
CTL(3-0)
FILT
VD
Function
Data Output Clock
HSYNC Output Clock (Phase-Aligned with DATACK)
VSYNC Output Clock (Phase-Aligned with DATACK)
SOG Slicer Output
Odd/Even Field Output
Control 3, 2, 1, and 0.
Connection for External Filter Components for PLL
Analog Power Supply and DVI Terminators
Value
VDD
VDD
VDD
VDD
VDD
VDD
83
82
49
50
51
52
35
34
38
37
41
40
43
VDD
PVDD
DVDD
GND
SDA
SCL
DDCSCL
DDCSDA
MCL
MDA
Rx0+
Rx0−
Rx1+
Rx1−
Rx2+
Rx2−
RxC+
Output Power Supply
PLL Power Supply
Digital Logic Power Supply
Ground
Serial Port Data I/O
Serial Port Data Clock
HDCP Slave Serial Port Data Clock
HDCP Slave Serial Port Data I/O
HDCP Master Serial Port Data Clock
HDCP Master Serial Port Data I/O
Digital Input Channel 0 True
Digital Input Channel 0 Complement
Digital Input Channel 1 True
Digital Input Channel 1 Complement
Digital Input Channel 2 True
Digital Input Channel 2 Complement
Digital Data Clock True
1.8 V to 3.3 V
1.8 V
1.8 V
0V
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
3.3 V CMOS
TMDS
TMDS
TMDS
TMDS
TMDS
TMDS
TMDS
44
88
46
RxC−
DE
RTERM
Digital Data Clock Complement
Data Enable
Sets Internal Termination Resistance
TMDS
3.3 V CMOS
500 Ω
3.3 V
Table 6. Pin Function Descriptions
Mnemonic
INPUTS
RAIN0
GAIN0
BAIN0
RAIN1
GAIN1
BAIN1
B
B
Rx0+
Rx0−
Rx1+
Rx1−
Rx2+
Rx2−
Description
Analog Input for the Red Channel 0.
Analog Input for the Green Channel 0.
Analog Input for the Blue Channel 0.
Analog Input for the Red Channel 1.
Analog Input for the Green Channel 1.
Analog Input for Blue Channel 1.
High impedance inputs that accept the red, green, and blue channel graphics signals, respectively. The three channels
are identical and can be used for any colors, but colors are assigned for convenient reference. They accommodate input
signals ranging from 0.5 V to 1.0 V full scale. Signals should be ac-coupled to these pins to support clamp operation
(see Figure 3 for an input reference circuit).
Digital Input Channel 0 True.
Digital Input Channel 0 Complement.
Digital Input Channel 1 True.
Digital Input Channel 1 Complement.
Digital Input Channel 2 True.
Digital input Channel 2 Complement.
These six pins receive three pairs of transition minimized differential signaling (TMDS) pixel data (at 10× the pixel rate)
from a digital graphics transmitter.
Rev. 0 | Page 8 of 48
AD9396
Mnemonic
RxC+
RxC−
HSYNC 0
HSYNC 1
VSYNC 0
VSYNC 1
SOGIN 0
SOGIN 1
EXTCLK/COAST
EXTCLK/COAST
RTERM
PWRDN
FILT
OUTPUTS
HSOUT
VSOUT
SOGOUT
O/E FIELD
Description
Digital Data Clock True.
Digital Data Clock Complement.
This clock pair receives a TMDS clock at 1× pixel data rate.
Horizontal Sync Input Channel 0.
Horizontal Sync Input Channel 1.
These inputs receive a logic signal that establishes the horizontal timing reference and provides the frequency
reference for pixel clock generation. The logic sense of this pin is controlled by Serial Register 0x12, Bits 5:4 (HSYNC
polarity). Only the leading edge of HSYNC is active; the trailing edge is ignored. When HSYNC polarity = 0, the falling
edge of HSYNC is used. When HSYNC polarity = 1, the rising edge is active. The input includes a Schmitt trigger for
noise immunity.
Vertical Sync Input Channel 0.
Vertical Sync Input Channel 1.
These are the inputs for vertical sync.
Sync-on-Green Input Channel 0.
Sync-on-Green Input Channel 1.
These inputs are provided to assist with processing signals with embedded sync, typically on the green channel. The
pin is connected to a high speed comparator with an internally generated threshold. The threshold level can be
programmed in 10 mV steps to any voltage between 10 mV and 330 mV above the negative peak of the input signal.
The default voltage threshold is 150 mV. When connected to an ac-coupled graphics signal with embedded sync, it
produces a noninverting digital output on SOGOUT. (This is usually a composite sync signal, containing both vertical
and horizontal sync (HSYNC) information that must be separated before passing the horizontal sync signal to HSYNC.)
When not used, this input should be left unconnected. For more details on this function and how it should be
configured, refer to the HSYNC and VSYNC Inputs section.
Coast Input to Clock Generator (Optional).
This input may be used to cause the pixel clock generator to stop synchronizing with HSYNC and continue producing a
clock at its current frequency and phase. This is useful when processing signals from sources that fail to produce
horizontal sync pulses during the vertical interval. The coast signal is generally not required for PC-generated signals.
The logic sense of this pin is controlled by coast polarity (Register 0x18, Bits 6:5). When not used, this pin may be
grounded and input coast polarity programmed to 1 (Register 0x18, Pin 5), or tied high (to VD through a 10 kΩ resistor)
and input coast polarity programmed to 0. Input coast polarity defaults to 1 at power-up. This pin is shared with the
EXTCLK function, which does not affect coast functionality. For more details on coast, see the description in the Clock
Generation section.
External Clock.
This allows the insertion of an external clock source rather than the internally generated PLL-locked clock. This pin is
shared with the coast function, does not affect EXTCLK functionality.
RTERM is the termination resistor used to drive the AD9396 internally to a precise 50 Ω termination for TMDS lines. This
should be a 500 Ω 1% tolerance resistor.
Power-Down Control/Three-State Control.
The function of this pin is programmable via Register 0x26 [2:1].
External Filter Connection.
For proper operation, the pixel clock generator PLL requires an external filter. Connect the filter shown in Figure 6 to
this pin. For optimal performance, minimize noise and parasitics on this node. For more information see the section on
PCB Layout Recommendations.
Horizontal Sync Output.
A reconstructed and phase-aligned version of the HSYNC input. Both the polarity and duration of this output can be
programmed via the serial bus registers. By maintaining alignment with DATACK and Data, data timing with respect to
horizontal sync can always be determined.
Vertical Sync Output.
The separated VSYNC from a composite signal or a direct passthrough of the VSYNC signal. The polarity of this output
can be controlled via serial bus bit (Register 0x24 [6]).
Sync-on-Green Slicer Output.
This pin outputs one of four possible signals (controlled by Register 0x24 [2:1]): raw SOG, raw HSYNC, regenerated
HSYNC from the filter, or the filtered HSYNC. See Figure 8, the Sync Processing Block Diagram, to view how this pin is
connected. (Note: besides slicing off SOG, the output from this pin is not processed on the AD9396. VSYNC separation
is performed via the sync separator.
Odd/Even Field Bit for Interlaced Video. This output identifies whether the current field (in an interlaced signal) is odd
or even. The polarity of this signal is programmable via Register 0x24 [4].
Rev. 0 | Page 9 of 48
AD9396
Mnemonic
DATA ENABLE
CTL(3 to 0)
SERIAL PORT
SDA
SCL
DDCSDA
DDCSCL
MDA
MCL
DATA OUTPUTS
Red [7:0]
Green [7:0]
Blue [7:0]
DATA CLOCK
OUTPUT
DATACK
POWER SUPPLY 1
VD (3.3 V)
VDD
(1.8 V to 3.3 V)
PVDD (1.8 V)
DVDD (1.8 V)
GND
1
Description
Data Enable that defines valid video. Can be received in the signal or generated by the AD9396.
Control 3, Control 2, Control 1, and Control 0 are output from the DVI stream. Refer to the DVI 1.0 specification for
explanation.
Serial Port Data I/O for Programming AD9396 Registers—I2C® Address is 0x98.
Serial Port Data Clock for Programming AD9396 Registers.
Serial Port Data I/O for HDCP Communications to Transmitter—I2C Address is 0x74 or 0x76.
Serial Port Data Clock for HDCP Communications to Transmitter.
Serial Port Data I/O to EEPROM with HDCP Keys—I2C Address is 0xA0.
Serial Port Data Clock to EEPROM with HDCP Keys.
Data Output, Red Channel.
Data Output, Green Channel.
Data Output, Blue Channel.
The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output is fixed, but is different if the
color space converter is used. When the sampling time is changed by adjusting the phase register, the output timing is
shifted as well. The DATACK and HSOUT outputs are also moved, so the timing relationship among the signals is
maintained.
Data Clock Output.
This is the main clock output signal used to strobe the output data and HSOUT into external logic. Four possible output
clocks can be selected with Register 0x25 [7:6]. These are related to the pixel clock (1/2× pixel clock, 1× pixel clock, 2×
frequency pixel clock and a 90° phase shifted pixel clock) and they are produced either by the internal PLL clock
generator or EXTCLK and are synchronous with the pixel sampling clock. The polarity of DATACK can also be inverted
via Register 0x24 [0]. The sampling time of the internal pixel clock can be changed by adjusting the phase register.
When this is changed, the pixel-related DATACK timing is shifted as well. The DATA, DATACK, and HSOUT outputs are all
moved, so the timing relationship among the signals is maintained.
Analog Power Supply.
These pins supply power to the ADCs and terminators. They should be as quiet and filtered as possible.
Digital Output Power Supply.
A large number of output pins (up to 27) switching at high speed (up to 150 MHz) generates many power supply
transients (noise). These supply pins are identified separately from the VD pins, so take care to minimize output noise
transferred into the sensitive analog circuitry. If the AD9396 is interfacing with lower voltage logic, VDD may be
connected to a lower supply voltage (as low as 1.8 V) for compatibility.
Clock Generator Power Supply.
The most sensitive portion of the AD9396 is the clock generation circuitry. These pins provide power to the clock PLL
and help the user design for optimal performance. The designer should provide quiet, noise-free power to these pins.
Digital Input Power Supply.
This supplies power to the digital logic.
Ground.
The ground return for all circuitry on-chip. It is recommended that the AD9396 be assembled on a single solid ground
plane, with careful attention to ground current paths.
The supplies should be sequenced such that VD and VDD are never less than 300 mV below DVDD. At no time should DVDD be more than 300 mV greater than VD or VDD.
Rev. 0 | Page 10 of 48
AD9396
DESIGN GUIDE
The AD9396 is a fully integrated solution for capturing analog
RGB or YUV signals and digitizing them for display on flat
panel monitors, projectors, or PDPs. In addition, the AD9396
has a digital interface for receiving DVI signals and is capable of
decoding HDCP-encrypted signals through connections to an
external EEPROM. The circuit is ideal for providing an
interface for HDTV monitors or as the front end to high
performance video scan converters.
Implemented in a high performance CMOS process, the
interface can capture signals with pixel rates of up to 150 MHz.
The AD9396 includes all necessary input buffering, signal dc
restoration (clamping), offset and gain (brightness and contrast)
adjustment, pixel clock generation, sampling phase control, and
output data formatting. Included in the output formatting is a
color space converter (CSC), which accommodates any input
color space and can output any color space. All controls are
programmable via a 2-wire serial interface. Full integration of
these sensitive analog functions makes system design straightforward and less sensitive to the physical and electrical
environment.
DIGITAL INPUTS
All digital control inputs (HSYNC, VSYNC, I2C) on the
AD9396 operate to 3.3 V CMOS levels. In addition, all digital
inputs except the TMDS (HDMI/DVI) inputs are 5 V tolerant.
(Applying 5 V to them does not cause any damage.) TMDS
inputs (Rx0+/Rx0−, Rx1+/Rx1−, Rx2+/Rx2−, and RxC+/RxC−)
must maintain a 100 Ω differential impedance (through proper
PCB layout) from the connector to the input where they are
internally terminated (50 Ω to 3.3 V). If additional ESD
protection is desired, use of a California Micro Devices (CMD)
CM1213 (among others) series low capacitance ESD protection
offers 8 kV of protection to the HDMI TMDS lines.
ANALOG INPUT SIGNAL HANDLING
The AD9396 has six high impedance analog input pins for the
red, green, and blue channels. They accommodate signals
ranging from 0.5 V p-p to 1.0 V p-p.
Signals are typically brought onto the interface board via a
DVI-I connector, a 15-pin D connector, or RCA-type connectors. The AD9396 should be located as close as practical to
the input connector. Signals should be routed via 75 Ω matched
impedance traces to the IC input pins.
At the input pins, the signal should be resistively terminated
(75 Ω to the signal ground return) and capacitively coupled to
the AD9396 inputs through 47 nF capacitors. These capacitors
form part of the dc restoration circuit.
In an ideal world of perfectly matched impedances, the best
performance can be obtained with the widest possible signal
bandwidth. The ultrawide bandwidth inputs of the AD9396
(330 MHz) can track the input signal continuously as it moves
from one pixel level to the next, and digitizes the pixel during a
long, flat pixel time. In many systems, however, there are
mismatches, reflections, and noise, which can result in excessive
ringing and distortion of the input waveform. This makes it
more difficult to establish a sampling phase that provides good
image quality. It has been shown that a small inductor in series
with the input is effective in rolling off the input bandwidth
slightly, and providing a high quality signal over a wider range
of conditions. Using a Fair-Rite #2508051217Z0 HIGH SPEED
SIGNAL CHIP BEAD inductor in the circuit, as shown in
Figure 3, gives good results in most applications.
47nF
RGB
INPUT
75Ω
RAIN
GAIN
BAIN
05690-003
GENERAL DESCRIPTION
Figure 3. Analog Input Interface Circuit
HSYNC AND VSYNC INPUTS
The interface also takes a horizontal sync signal, which is used
to generate the pixel clock and clamp timing. This can be either
a sync signal directly from the graphics source, or a preprocessed TTL or CMOS level signal.
The HSYNC input includes a Schmitt trigger buffer for
immunity to noise and signals with long rise times. In typical
PC-based graphic systems, the sync signals are TTL-level
drivers feeding unshielded wires in the monitor cable. As such,
no termination is required.
SERIAL CONTROL PORT
The serial control port is designed for 3.3 V logic. However, it is
tolerant of 5 V logic signals.
OUTPUT SIGNAL HANDLING
The digital outputs are designed to operate from 1.8 V to 3.3 V
(VDD).
CLAMPING
RGB Clamping
To properly digitize the incoming signal, the dc offset of the
input must be adjusted to fit the range of the on-board ADC.
Most graphics systems produce RGB signals with black at
ground and white at approximately 0.75 V. However, if sync
signals are embedded in the graphics, the sync tip is often at
ground and black is at 300 mV. Then white is at approximately
1.0 V. Some common RGB line amplifier boxes use emitterfollower buffers to split signals and increase drive capability.
Rev. 0 | Page 11 of 48
AD9396
This introduces a 700 mV dc offset to the signal, which must be
removed for proper capture by the AD9396.
to within ½ LSB in 10 lines with a clamp duration of 20 pixel
periods on a 75 Hz SXGA signal.
The key to clamping is to identify a portion (time) of the signal
when the graphic system is known to be producing black. An
offset is then introduced which results in the ADCs producing a
black output (Code 0x00) when the known black input is
present. The offset then remains in place when other signal
levels are processed, and the entire signal is shifted to eliminate
offset errors.
YUV Clamping
In most PC graphics systems, black is transmitted between
active video lines. With CRT displays, when the electron beam
has completed writing a horizontal line on the screen (at the
right side), the beam is deflected quickly to the left side of the
screen (called horizontal retrace) and a black signal is provided
to prevent the beam from disturbing the image.
Clamping to midscale rather than ground can be accomplished
by setting the clamp select bits in the serial bus register. Each of
the three converters has its own selection bit so that they can be
clamped to either midscale or ground independently. These bits
are located in Register 0x1B [7:5]. The midscale reference
voltage is internally generated for each converter.
In systems with embedded sync, a blacker-than-black signal
(HSYNC) is produced briefly to signal the CRT that it is time to
begin a retrace. For obvious reasons, it is important to avoid
clamping on the tip of HSYNC. Fortunately, there is virtually
always a period following HSYNC, called the back porch, where
a good black reference is provided. This is the time when
clamping should be done.
Auto-Offset
YUV graphic signals are slightly different from RGB signals in
that the dc reference level (black level in RGB signals) can be
at the midpoint of the graphics signal rather than the bottom.
For these signals it can be necessary to clamp to the midscale
range of the ADC range (128) rather than the bottom of the
ADC range (0).
The auto-offset circuit works by calculating the required offset
setting to yield a given output code during clamp. When this
block is enabled, the offset setting in the I2C is seen as a desired
clamp code rather than an actual offset. The circuit compares
the output code during clamp to the desired code and adjusts
the offset up or down to compensate.
Clamp timing employs the AD9396 internal clamp timing
generator. The clamp placement register is programmed with
the number of pixel periods that should pass after the trailing
edge of HSYNC before clamping starts. A second register
(clamp duration) sets the duration of the clamp. These are both
8-bit values, providing considerable flexibility in clamp
generation. The clamp timing is referenced to the trailing edge
of HSYNC because, though HSYNC duration can vary widely,
the back porch (black reference) always follows HSYNC. A
good starting point for establishing clamping is to set the clamp
placement to 0x08 (providing 8 pixel periods for the graphics
signal to stabilize after sync) and set the clamp duration to 0x14
(giving the clamp 20 pixel periods to re-establish the black
reference). For three-level syncs embedded on the green
channel, it is necessary to increase the clamp placement to
beyond the positive portion of the sync. For example, a good
clamp placement (Register 0x19) for a 720p input is 0x26. This
delays the start of clamp by 38 pixel clock cycles after the rising
edge of the three-level sync, allowing plenty of time for the
signal to return to a black reference.
The offset on the AD9396 can be adjusted automatically to a
specified target code. This option allows the user to set the
offset to any value and be assured that all channels with the
same value programmed into the target code will match. This
eliminates any need to adjust the offset at the factory. This
function is capable of running continuously any time the clamp
is asserted.
Clamping is accomplished by placing an appropriate charge on
the external input coupling capacitor. The value of this capacitor affects the performance of the clamp. If it is too small,
there is a significant amplitude change during a horizontal line
time (between clamping intervals). If the capacitor is too large,
then it takes excessively long for the clamp to recover from a
large change in the incoming signal offset. The recommended
value (47 nF) results in recovering from a step error of 100 mV
Sync-on-Green (SOG)
There is an offset adjust register for each channel, namely the
offset registers at the 0x08, 0x0A, and 0x0C addresses. The
offset adjustment is a signed (twos complement) number with
±64 LSB range. The offset adjustment is added to whatever
offset the auto-offset comes up with. For example: using ground
clamp, the target code is set to 4. To get this code, the autooffset generates an offset of 68. If the offset adjustment is set to
+10, the offset sent to the converter is 78. Likewise, if the offset
adjust is set to −10, the offset sent to the converter is 58. Refer
to application note AN-775, Implementing the Auto-Offset
Function of the AD9880, for a detailed description of how to use
this function.
The SOG input operates in two steps. First, it sets a baseline
clamp level from the incoming video signal with a negative peak
detector. Second, it sets the sync trigger level to a programmable level (typically 150 mV) above the negative peak. The
SOG input must be ac-coupled to the green analog input
through its own capacitor. The value of the capacitor must be
1 nF ± 20%. If SOG is not used, this connection is not required.
Rev. 0 | Page 12 of 48
AD9396
Note that the SOG signal is always negative polarity. For more
detail on setting the SOG threshold and other SOG-related
functions, see the Sync Processing section.
47nF
RAIN
The PLL characteristics are determined by the loop filter design,
the PLL charge pump current, and the VCO range setting. The
loop filter design is shown in Figure 6. Recommended settings
of the VCO range and charge pump current for VESA standard
display modes are listed in Table 9.
47nF
BAIN
CP
8nF
47nF
GAIN
05690-006
SOG
PVD
RZ
1.5kΩ
05690-004
1nF
CZ
80nF
FILT
Figure 4. Typical Clamp Configuration for RGB/YUV Applications
Figure 6. PLL Loop Filter Detail
Clock Generation
A PLL is employed to generate the pixel clock. In this PLL,
the HSYNC input provides a reference frequency. A voltage
controlled oscillator (VCO) generates a much higher pixel clock
frequency. This pixel clock is divided by the PLL divide value
(Register 0x01 and Register 0x02) and phase compared with the
HSYNC input. Any error is used to shift the VCO frequency
and to maintain the lock between the two signals.
The stability of this clock is a very important element in providing the clearest and most stable image. During each pixel time,
there is a period during which the signal slews from the old
pixel amplitude and settles at its new value. This is followed by a
time when the input voltage is stable before the signal must slew
to a new value. The ratio of the slewing time to the stable time is
a function of the bandwidth of the graphics DAC and the
bandwidth of the transmission system (cable and termination).
It is also a function of the overall pixel rate. Clearly, if the
dynamic characteristics of the system remain fixed, then the
slewing and settling time is likewise fixed. This time must be
subtracted from the total pixel period, leaving the stable period.
At higher pixel frequencies, the total cycle time is shorter and
the stable pixel time also becomes shorter.
INVALID SAMPLE TIMES
•
The 12-bit divisor register (R0x01, R0x02). The input
HSYNC frequency range can be any frequency which,
combined with the PLL_Div, does not exceed the VCO
range. The PLL multiplies the frequency of the HSYNC
signal, producing pixel clock frequencies in the range of
10 MHz to 100 MHz. The divisor register controls the
exact multiplication factor.
•
The 2-bit VCO range register (R0x03). To improve the
noise performance of the AD9396, the VCO operating
frequency range is divided into four overlapping regions.
The VCO range register sets this operating range. The
frequency ranges for the lowest and highest regions are
shown in Table 7.
Table 7.
VCORNGE
00
01
10
11
•
05690-005
PIXEL CLOCK
Four programmable registers are provided to optimize the
performance of the PLL. These registers are:
Figure 5. Pixel Sampling Times
Any jitter in the clock reduces the precision with which the
sampling time can be determined and must also be subtracted
from the stable pixel time. Considerable care has been taken in
the design of the AD9396 clock generation circuit to minimize
jitter. The clock jitter of the AD9396 is less than 13% of the total
pixel time in all operating modes, making the reduction in the
valid sampling time due to jitter negligible.
Pixel Rate Range
12 to 30
30 to 60
60 to 120
120 to 150
The 5-bit phase adjust register (R0x05). The phase of the
generated sampling clock can be shifted to locate an
optimum sampling point within a clock cycle. The phase
adjust register provides 32 phase-shift steps of 11.25° each.
The HSYNC signal with an identical phase shift is available
through the HSOUT pin.
The coast pin or the internal coast is used to allow the PLL to
continue to run at the same frequency, in the absence of the
incoming HSYNC signal or during disturbances in HSYNC
(such as equalization pulses). This can be used during the
vertical sync period or any other time that the HSYNC signal is
unavailable. The polarity of the coast signal can be set through
the coast polarity register. Also, the polarity of the HSYNC
signal can be set through the HSYNC polarity register. For both
HSYNC and coast, a value of 1 is active high. The internal coast
function is driven from the VSYNC signal, which is typically a
time when HSYNC signals can be disrupted with extra
equalization pulses.
Rev. 0 | Page 13 of 48
AD9396
Power Management
The AD9396 uses the activity detect circuits, the active interface
bits in the serial bus, the active interface override bits, the
power-down bit, and the power-down pin to determine the
correct power state. There are four power states: full-power,
seek mode, auto power-down, and power-down.
Table 8 summarizes how the AD9396 determines the power
mode and the circuitry that is powered on/off in each of these
modes. The power-down command has priority and then the
automatic circuitry. The power-down pin (Pin 81—polarity set
by Register 0x26[3]) can drive the chip into four power-down
options. Bit 2 and Bit 1 of Register 0x26 control these four
options. Bit 0 controls whether the chip is powered down or the
outputs are placed in high impedance mode (with the exception
of SOG). Bit 7 to Bit 4 of Register 0x26 control whether the
outputs, SOG, Sony Philips digital interface (SPDIF ) or I2S (IIS
or Inter-IC sound bus) outputs are in high impedance mode or
not. See the 2-Wire Serial Control Register Detail section for
more detail.
Table 8. Power-Down Mode Descriptions
Mode
Full Power
Seek Mode
Seek Mode
Power-Down 1
1
1
1
Inputs
Sync Detect 2
1
0
0
Power-Down
0
X
Auto PD Enable 3
X
0
1
Power-On or Comments
Everything
Everything
Serial bus, sync activity detect, SOG, band gap
reference
Serial bus, sync activity detect, SOG, band gap
reference
1
Power-down is controlled via Bit 0 in Serial Bus Register 0x26.
Sync detect is determined by OR’ing Bit 7 to Bit 2 in Serial Bus Register 0x15.
3
Auto power-down is controlled via Bit 7 in Serial Bus Register 0x27.
2
Table 9. Recommended VCO Range and Charge Pump Current Settings for Standard Display Formats
Standard
VGA
Resolution
640 × 480
SVGA
800 × 600
XGA
1024 × 768
SXGA
1280 × 1024
1280 × 1024
480i
480p
720p
1035i
1080i
1080p
TV
1
Refresh Rate
(Hz)
60
72
75
85
56
60
72
75
85
60
70
75
80
85
60
75
60
60
60
60
60
60
Horizontal
Frequency (kHz)
31.5
37.7
37.5
43.3
35.1
37.9
48.1
46.9
53.7
48.4
56.5
60.0
64.0
68.3
64.0
80.0
15.75
31.47
45
33.75
33.75
67.5
Pixel Rate (MHz)
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
85.500
94.500
108.000
135.000
13.51
27
74.25
74.25
74.25
148.5
These are preliminary recommendations for the analog PLL and are subject to change without notice.
Rev. 0 | Page 14 of 48
VCO Range 1
00
01
01
01
01
01
01
01
01
10
10
10
10
10
10
11
00
00
10
10
10
11
Current1
101
011
100
100
100
101
110
110
110
011
100
100
101
110
110
110
010
101
100
100
100
110
AD9396
TIMING
The output data clock signal is created so that its rising edge
always occurs between data transitions and can be used to latch
the output data externally.
There is a pipeline in the AD9396, which must be flushed
before valid data becomes available. This means 23 data sets are
presented before valid data is available.
The timing diagram in Figure 7 shows the operation of the
AD9396.
Coast Timing
In most computer systems, the HSYNC signal is provided continuously on a dedicated wire. In these systems, the coast input
and function are unnecessary, and should not be used. The pin
should be permanently connected to the inactive state.
tPER
tDCYCLE
DATACK
tSKEW
05690-009
DATA
HSOUT
Three things happen to HSYNC in the AD9396. First, the
polarity of HSYNC input is determined and thus has a known
output polarity. The known output polarity can be programmed
either active high or active low (Register 0x24, Bit 7). Second,
HSOUT is aligned with DATACK and data outputs. Third, the
duration of HSOUT (in pixel clocks) is set via Register 0x23.
HSOUT is the sync signal that should be used to drive the rest
of the display system.
Figure 7. Output Timing
HSYNC Timing
Horizontal sync (HSYNC) is processed in the AD9396 to
eliminate ambiguity in the timing of the leading edge with
respect to the phase-delayed pixel clock and data.
The HSYNC input is used as a reference to generate the pixel
sampling clock. The sampling phase can be adjusted, with
respect to HSYNC, through a full 360° in 32 steps via the phase
adjust register (to optimize the pixel sampling time). Display
systems use HSYNC to align memory and display write cycles,
so it is important to have a stable timing relationship between
the HSYNC output (HSOUT) and data clock (DATACK).
In some systems, however, HSYNC is disturbed during the
vertical sync period (VSYNC). In some cases, HSYNC pulses
disappear. In other systems, such as those that employ
composite sync (Csync) signals or embedded SOG, HSYNC
includes equalization pulses or other distortions during
VSYNC. To avoid upsetting the clock generator during VSYNC,
it is important to ignore these distortions. If the pixel clock PLL
sees extraneous pulses, it attempts to lock to this new frequency,
and changes frequency by the end of the VSYNC period. It then
takes a few lines of correct HSYNC timing to recover at the
beginning of a new frame, tearing the image at the top of the
display.
The coast input is provided to eliminate this problem. It is an
asynchronous input that disables the PLL input and allows the
clock to free-run at its then-current frequency. The PLL can
free-run for several lines without significant frequency drift.
Coast can be generated internally by the AD9396 (see
Register 0x12[1]), can be driven directly from a VSYNC input,
or can be provided externally by the graphics controller.
Rev. 0 | Page 15 of 48
AD9396
Sync Processing
is to extract VSYNC from the composite sync signal, which can
come from either the sync slicer or the HSYNC input. The
HSYNC filter is used to eliminate any extraneous pulses from
the HSYNC or SOGIN inputs, outputting a clean, low jitter
signal that is appropriate for mode detection and clock
generation. The HSYNC regenerator is used to re-create a clean,
although not low jitter, HSYNC signal that can be used for
mode detection and counting HSYNCs per VSYNC. The
VSYNC filter is used to eliminate spurious VSYNCs, maintain a
stable timing relationship between the VSYNC and HSYNC
output signals, and generate the odd/even field output. The
coast generator creates a robust coast signal that allows the PLL
to maintain its frequency in the absence of HSYNC pulses.
The inputs of the sync processing section of the AD9396 are
combinations of digital HSYNCs and VSYNCs, analog sync-ongreen, or sync-on-Y signals, and an optional external coast
signal. From these signals, it generates a precise, jitter-free (9%
or less at 95 MHz) clock from its PLL; an odd/even field signal;
HSYNC and VSYNC out signals; a count of HSYNCs per
VSYNC; and a programmable SOG output. The main sync
processing blocks are the sync slicer, sync separator, HSYNC
filter, HSYNC regenerator, VSYNC filter, and coast generator.
The sync slicer extracts the sync signal from the green graphics
or luminance video signal that is connected to the SOGIN input
and outputs a digital composite sync. The sync separator’s task
CHANNEL
SELECT [0x11:3]
HSYNC [0x11:7]
SELECT
HSYNC 0
PD2
AD1
MUX
HSYNC FILTER
AND
REGENERATOR
MUX
HSYNC 1
AD1
FH4
PD2
RH3
SYNC
SLICER
SOGIN 0
AD1
MUX
SYNC
SLICER
SOGIN 1
SP SYNC FILTER EN
0x21:7
MUX
SP5
SOG OUT
AD1
VSYNC 0
VSYNC
AD1
PD2
AD1
PD2
MUX
SOGOUT SELECT
0x24:2,1
SYNC
PROCESSOR
AND
VSYNC FILTER
MUX
VSYNC
FILTERED
VSYNC
MUX
VSYNC OUT
VSYNC 1
VSYNC FILTER EN
0x21:5
FILTER COAST VSYNC
0x12:0
PLL SYNC FILTER EN
0x21:6
MUX
HSYNC/VSYNC
COUNTER
REG 26H, 27H
SP5
O/E
FIELD
HSYNC
COAST
MUX
COAST
AD9396
SP5
HSYNC OUT
SP5
DATACK
PLL CLOCK
GENERATOR
COAST SELECT
0x12:1
1ACTIVITY DETECT
2POLARITY DETECT
05690-007
3REGENERATED HSYNC
4FILTERED HSYNC
5SET POLARITY
Figure 8. Sync Processing Block Diagram
Rev. 0 | Page 16 of 48
AD9396
Sync Slicer
The purpose of the sync slicer is to extract the sync signal from
the green graphics or luminance video signal that is connected
to the SOGIN input. The sync signal is extracted in a two-step
process. First, the SOG input (typically 0.3 V below the black
level) is detected and clamped to a known dc voltage. Next, the
signal is routed to a comparator with a variable trigger level (set
by Register 0x1D, Bits [7:3]), but nominally 0.128 V above the
clamped voltage. The sync slicer output is a digital composite
sync signal containing both HSYNC and VSYNC information
(see Figure 9).
Sync Separator
As part of sync processing, the sync separator’s task is to extract
VSYNC from the composite sync signal. It works on the idea
that the VSYNC signal stays active for a much longer time than
the HSYNC signal. By using a digital low-pass filter and a
digital comparator, it rejects pulses with small durations (such
as HSYNCs and equalization pulses) and only passes pulses
with large durations, such as VSYNC (see Figure 9).
The threshold of the digital comparator is programmable for
maximum flexibility. To program the threshold duration, write
a value (N) to Register 0x11. The resulting pulse width is
N × 200 ns. So if N = 5, the digital comparator threshold is 1 μs.
Any pulses less than 1 μs are rejected, while any pulse greater
than 1 μs passes through.
The sync separator on the AD9396 is simply an 8-bit digital
counter with a 6 MHz clock. It works independently of the
polarity of the composite sync signal. Polarities are determined
elsewhere on the chip. The basic idea is that the counter counts
up when HSYNC pulses are present. But because HSYNC
pulses are relatively short in width, the counter only reaches a
value of N before the pulse ends. It then starts counting down
until eventually reaching 0 before the next HSYNC pulse
arrives. The specific value of N varies for different video modes,
but is always less than 255. For example, with a 1 μs width
HSYNC, the counter only reaches 5 (1 μs/200 ns = 5). Now,
when VSYNC is present on the composite sync the counter also
counts up. However, because the VSYNC signal is much longer,
it counts to a higher number, M. For most video modes, M is at
least 255. So VSYNC can be detected on the composite sync
signal by detecting when the counter counts to higher than N.
The specific count that triggers detection, T, can be
programmed through the Serial Register 0x11.
Once VSYNC has been detected, there is a similar process to
detect when it goes inactive. At detection, the counter first
resets to 0, then starts counting up when VSYNC finishes. As in
the previous case, it detects the absence of VSYNC when the
counter reaches the threshold count, T. In this way, it rejects
noise and/or serration pulses. Once VSYNC is detected to be
absent, the counter resets to 0 and begins the cycle again.
There are two things to keep in mind when using the sync
separator. First, the resulting clean VSYNC output is delayed
from the original VSYNC by a duration equal to the digital
comparator threshold (N × 200 ns). Second, there is some
variability to the 200 ns multiplier value. The maximum variability over all operating conditions is ±20% (160 ns to 240 ns).
Because normal VSYNC and HSYNC pulse widths differ by a
factor of about 500 or more, 20% variability is not an issue.
NEGATIVE PULSE WIDTH = 40 SAMPLE CLOCKS
700mV MAXIMUM
SOGIN
+300mV
0mV
–300mV
SOGOUT OUTPUT
CONNECTED TO
HSIN
05690-008
COMPOSITE
SYNC
AT HSIN
VSOUT
FROM SYNC
SEPARATOR
Figure 9. Sync Slicer and Sync Separator Output
Rev. 0 | Page 17 of 48
AD9396
HSYNC Filter and Regenerator
The HSYNC filter is used to eliminate any extraneous pulses
from the HSYNC or SOGIN inputs, outputting a clean, low
jitter signal that is appropriate for mode detection and clock
generation. The HSYNC regenerator is used to re-create a clean,
although not low jitter, HSYNC signal that can be used for
mode detection and counting HSYNCs per VSYNC. The
HSYNC regenerator has a high degree of tolerance to
extraneous and missing pulses on the HSYNC input, but is not
appropriate for use by the PLL in creating the pixel clock
because of jitter.
timing, program a value (x) into Register 0x20. The resulting
filter window time is ±x times 25 ns around the regenerated
HSYNC leading edge. Just as for the sync separator threshold
multiplier, allow a ±20% variance in the 25 ns multiplier to
account for all operating conditions (20 ns to 30 ns range).
The HSYNC regenerator runs automatically and requires no
setup to operate. The HSYNC filter requires setting up a filter
window. The filter window sets a periodic window of time
around the regenerated HSYNC leading edge where valid
HSYNCs are allowed to occur. The general idea is that
extraneous pulses on the sync input occur outside of this filter
window and thus are filtered out. To set the filter window
The filtered HSYNC (rather than the raw HSYNC/SOGIN
signal) for pixel clock generation by the PLL is controlled by
Register 0x21[6]. The regenerated HSYNC (rather than the
raw HSYNC/SOGIN signal) for sync processing is controlled by
Register 0x21[7]. Use of the filtered HSYNC and regenerated
HSYNC is recommended. See Figure 10 for an illustration of a
filtered HSYNC.
A second output from the HSYNC filter is a status bit
(Register 0x16[0]) that tells whether extraneous pulses are
present on the incoming sync signal. Extraneous pulses are
often included for copy protection purposes; this status bit can
be used to detect that.
HSIN
FILTER
WINDOW
HSOUT
VSYNC
EQUALIZATION
PULSES
EXPECTED
EDGE
05690-010
FILTER
WINDOW
Figure 10. Sync Processing Filter
Rev. 0 | Page 18 of 48
AD9396
VSYNC Filter and Odd/Even Fields
DE GENERATOR
The VSYNC filter is used to eliminate spurious VSYNCs,
maintain a consistent timing relationship between the VSYNC
and HSYNC output signals, and generate the odd/even field
output.
The AD9396 has an on-board generator for DE, for start of
active video (SAV), and for end of active video (EAV), all of
which are necessary for describing the complete data stream for
a BT656-compatible output. In addition to this particular
output, it is possible to generate the DE for cases in which a
scaler is not used. This signal alerts the following circuitry as to
which are displayable video pixels.
The filter works by examining the placement of VSYNC with
respect to HSYNC and, if necessary, slightly shifting it in time at
the VSOUT output. The goal is to keep the VSYNC and
HSYNC leading edges from switching at the same time,
eliminating confusion as to when the first line of a frame
occurs. Enabling the VSYNC filter is done with Register
0x21[5]. Use of the VSYNC filter is recommended for all cases,
including interlaced video and is required when using the
HSYNC per VSYNC counter. Figure 12 illustrates even/odd
field determination in two situations.
SYNC SEPARATOR THRESHOLD
FIELD 1
QUADRANT
2
3
FIELD 0
4
1
FIELD 1
2
3
FIELD 0
4
1
HSIN
VSIN
The AD9396 contains a filter that allows it to convert a signal
from YCrCb 4:4:4 to YCrCb 4:2:2 while maintaining the
maximum accuracy and fidelity of the original signal.
Input Color Space to Output Color space
The AD9396 can support a wide variety of output formats, such
as the following:
•
RGB 24-bit
•
4:4:4 YCrCb 8-bit
•
4:2:2 YCrCb 8-bit, 10-bit, and 12-bit
•
Dual 4:2:2 YCrCb 8-bit
Color Space Conversion (CSC) Matrix
05690-011
VSOUT
O/E FIELD
EVEN FIELD
Figure 11.
SYNC SEPARATOR THRESHOLD
FIELD 1
QUADRANT
4:4:4 TO 4:2:2 FILTER
2
3
FIELD 0
4
1
FIELD 1
2
3
FIELD 0
4
1
HSIN
The color space conversion (CSC) matrix in the AD9396
consists of three identical processing channels. In each channel,
three input values are multiplied by three separate coefficients.
Also included are an offset value for each row of the matrix and
a scaling multiple for all values. Each value has a 13-bit, twos
complement resolution to ensure the signal integrity is maintained. The CSC is designed to run at speeds up to 150 MHz
supporting resolutions up to 1080p at 60 Hz. With any-to-any
color space support, formats such as RGB, YUV, YCbCr, and
others are supported by the CSC.
VSIN
O/E FIELD
ODD FIELD
05690-012
VSOUT
The main inputs, RIN, GIN, and BIN come from the 8-bit to 12-bit
inputs from each channel. These inputs are based on the input
format detailed in Table 11. The mapping of these inputs to the
CSC inputs is shown in Table 10.
Table 10. CSC Port Mapping
Figure 12. VSYNC Filter—Odd/Even
DVI RECEIVER
The DVI receiver section of the AD9396 allows the reception of
a digital video stream compatible with DVI 1.0. Embedded in
this data stream are HSYNCs, VSYNCs and display enable (DE)
signals. DVI restricts the received format to RGB, but the
inclusion of a programmable color space converter (CSC)
allows the output to be tailored to any format necessary. With
this, the scaler following the AD9396 can specify that it always
wishes to receive a particular format—for instance, 4:2:2
YCrCb—regardless of the transmitted mode. If RGB is sent, the
CSC can easily convert that to 4:2:2 YCrCb while relieving the
scaler of this task.
Input Channel
R/CR
Gr/Y
B/CB
CSC Input Channel
RIN
GIN
BIN
B
One of the three channels is represented in Figure 13. In each
processing channel the three inputs are multiplied by three
separate coefficients marked a1, a2, and a3. These coefficients
are divided by 4096 to obtain nominal values ranging from
−0.9998 to +0.9998. The variable labeled ‘a4’ is used as an offset
control. The CSC_Mode setting is the same for all three
processing channels. This multiplies all coefficients and offsets
by a factor of 2CSC_Mode.
Rev. 0 | Page 19 of 48
AD9396
The functional diagram for a single channel of the CSC, as
shown in Figure 13, is repeated for the remaining G and B
channels. The coefficients for these channels are b1, b2, b3, b4,
c1, c2, c3, and c4.
latch the output data externally. There is a pipeline in the
AD9396, which must be flushed before valid data becomes
available. This means six data sets are presented before valid
data is available.
A programming example and register settings for several
common conversions are listed in the Color Space Converter
(CSC) Common Settings.
CSC_Mode[1:0]
a4[12:0]
a1[12:0]
RIN [11:0]
For a detailed functional description and more programming
examples, refer to the application note AN-795, AD9880 Color
Space Converter User's Guide.
×
1
4096
×
+
+
×4
2
×2
1
+
ROUT [11:0]
a2[12:0]
0
BIN [11:0]
TIMING DIAGRAMS
×
×
1
4096
×
1
4096
The following timing diagrams show the operation of the
AD9396.The output data clock signal is created so that its rising
edge always occurs between data transitions and can be used to
P0
DATAIN
P1
P2
P3
P4
GIN [11:0]
×
05690-013
a3[12:0]
Figure 13. Single CSC Channel
P5
P6
P7
P8
P9
P10
P11
HSIN
DATACK
8 CLOCK CYCLE DELAYS
DATAOUT
P0
P1
P2
P3
05690-014
2 CLOCK CYCLE DELAYS
HSOUT
Figure 14. RGB ADC Timing
DATAIN
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
HSIN
DATACK
8 CLOCK CYCLE DELAYS
YOUT
CB/CROUT
Y0
Y1
Y2
Y3
B0
R0
B2
R2
2 CLOCK CYCLE DELAYS
05690-015
HSOUT
NOTES:
1. PIXEL AFTER HSOUT CORRESPONDS TO BLUE INPUT.
2. EVEN NUMBER OF PIXEL DELAYS BETWEEN HSOUT AND DATAOUT.
Figure 15. YCrCb ADC Timing
Table 11.
Port
Bit
4:4:4
4:2:2
4:4:4 DDR
4:2:2 to 12
1
Red
7
6
5
4
Red/Cr [7:0]
CbCr [7:0]
DDR ↑ 1 G [3:0]
DDR ↓ R [7:0]
CbCr [11:0]
3
2
1
DDR ↑ B [7:4]
0
Green
7
6
5
4
Green/Y [7:0]
Y [7:0]
DDR ↑ B [3:0]
DDR ↓ G [7:4]
3
2
1
0
DDR 4:2:2 ↑ CbCr [11:0]
DDR 4:2:2 ↓ Y,Y [11:0]
Y [11:0]
Arrows in the table indicate clock edge. Rising edge of clock = ↑, falling edge = ↓.
Rev. 0 | Page 20 of 48
Blue
7 6 5
4
3
2
Blue/Cb [7:0]
DDR 4:2:2 ↑ CbCr ↓ Y, Y
1
0
AD9396
2-WIRE SERIAL REGISTER MAP
The AD9396 is initialized and controlled by a set of registers that determines the operating modes. An external controller is employed to
write and read the control registers through the 2-wire serial interface port.
Table 12. Control Register Map
Hex
Address
0x00
0x01
0x02
0x03
Read/Write
or Read Only
Read
Read/Write
Read/Write
Read/Write
Bits
[7:0]
[7:0]
[7:4]
[7:6]
[5:3]
[2]
Default
Value
00000000
01101001
1101****
01******
**001***
*****0**
0x04
0x05
Read/Write
Read/Write
[7:3]
[7:0]
0x06
Read/Write
0x07
Register Name
Chip Revision
PLL Divider MSB
PLL Divider
VCO Range
Charge Pump
External Clock
Enable
Description
Chip revision ID.
PLL feedback divider value MSB.
PLL feedback divider value.
VCO range.
Charge pump current control for PLL.
Selects the external clock input rather than the internal PLL clock.
10000***
10000000
Phase Adjust
Red Gain
[7:0]
10000000
Green Gain
Read/Write
[7:0]
10000000
Blue Gain
0x08
0x09
0x0A
Read/Write
Read/Write
Read/Write
[7:0]
[7:0]
[7:0]
00000000
10000000
00000000
0x0B
0x0C
0x0D
0x0E
Read/Write
Read/Write
Read/Write
Read/Write
[7:0]
[7:0]
[7:0]
[7:0]
10000000
00000000
10000000
00100000
0x0F
Read/Write
[7:2]
010000**
0x10
Read/Write
[7:2]
010000**
0x11
Read/Write
[7]
0*******
Red Offset Adjust
Red Offset
Green Offset
Adjust
Green Offset
Blue Offset Adjust
Blue Offset
Sync Separator
Threshold
SOG Comparator
Threshold Enter
SOG Comparator
Threshold Exit
HSYNC Source
Selects the clock phase to use for the ADC clock.
Controls the gain of the red channel PGA. 0 = low gain,
255 = high gain.
Controls the gain of the green channel PGA. 0 = low gain,
255 = high gain.
Controls the gain of the blue channel PGA. 0 = low gain,
255 = high gain.
User adjustment of auto-offset. Allows user control of brightness.
Red offset/target code. 0 = small offset, 255 = large offset.
User adjustment of auto-offset. Allows user control of brightness.
[6]
*0******
HSYNC Source
Override
[5]
**0*****
VSYNC Source
[4]
***0****
VSYNC Source
Override
[3]
****0***
Channel Select
[2]
*****0**
Channel Select
Override
[1]
******0*
Interface Select
[0]
*******0
Interface Override
Green offset/target code. 0 = small offset, 255 = large offset.
User adjustment of auto-offset. Allows user control of brightness.
Blue offset/target code. 0 = small offset, 255 = large offset.
Selects the maximum HSYNC pulse width for composite sync
separation.
The enter level for the SOG slicer. Must be less than or equal to the
exit level.
The exit level for the SOG slicer. Must be greater than or equal to
the enter level.
0 = HSYNC.
1 = SOG.
0 = auto HSYNC source.
1 = manual HSYNC source.
0 = VSYNC.
1 = VSYNC from SOG.
0 = auto HSYNC source.
1 = manual HSYNC source.
0 = Channel 0.
1 = Channel 1.
0 = autochannel select.
1 = manual channel select.
0 = analog interface.
1 = digital interface.
0 = auto-interface select.
1 = manual interface select.
Rev. 0 | Page 21 of 48
AD9396
Hex
Address
0x12
0x13
0x14
0x15
0x16
Read/Write
or Read Only
Read/Write
Read/Write
Read/Write
Read
Read
Bits
[7]
Default
Value
1*******
[6]
*0******
HSYNC Polarity
Override
[5]
**1*****
Input VSYNC
Polarity
[4]
***0****
VSYNC Polarity
Override
[3]
****1***
Input Coast
Polarity
Register Name
Input HSYNC
Polarity
[2]
*****0**
Coast Polarity
Override
[1]
******0*
Coast Source
[0]
*******1
Filter Coast VSYNC
[7:0]
[7:0]
[7]
00000000
00000000
0*******
Precoast
Postcoast
HSYNC 0
Detected
[6]
*0******
HSYNC 1
Detected
[5]
**0*****
VSYNC 0 Detected
[4]
***0****
VSYNC 1 Detected
[3]
****0***
SOG 0 Detected
[2]
*****0**
SOG1 Detected
[1]
******0*
Coast Detected
[7]
0*******
HSYNC 0 Polarity
[6]
*0******
HSYNC 1 Polarity
[5]
**0*****
VSYNC 0 Polarity
[4]
***0****
VSYNC 1 Polarity
[3]
****0***
Coast Polarity
[2]
*****0**
[1]
******0*
Pseudo Sync
Detected
Sync Filter Locked
Description
0 = active low.
1 = active high.
0 = auto HSYNC polarity.
1 = manual HSYNC polarity.
0 = active low.
1 = active high.
0 = auto VSYNC polarity.
1 = manual VSYNC polarity.
0 = active low.
1 = active high.
0 = auto-coast polarity.
1 = manual coast polarity.
0 = internal coast.
1 = external coast.
0 = Use raw VSYNC for coast generation.
1 = Use filtered VSYNC for coast generation.
Number of HSYNC periods before VSYNC to coast.
Number of HSYNC periods after VSYNC to coast.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = not detected.
1 = detected.
0 = active low.
1 = active high.
0 = active low.
1 = active high.
0 = active low.
1 = active high.
0 = active low.
1 = active high.
0 = active low.
1 = active high.
0 = not detected.
1 = detected.
0 = not locked.
1 = locked.
Rev. 0 | Page 22 of 48
AD9396
Hex
Address
Read/Write
or Read Only
Bits
[0]
Default
Value
*******0
0x17
Read
[3:0]
****0000
0x18
Read
[7:0]
00000000
0x19
0x1A
0x1B
Read/Write
Read/Write
Read/Write
[7:0]
[7:0]
[7]
00001000
00010100
0*******
[6]
*0******
Green Clamp
Select
[5]
**0*****
Blue Clamp Select
[4]
***0****
Clamp During
Coast Enable
[3]
****0***
Clamp Disable
[1]
******1*
Programmable
Bandwidth
0x1C
Read/Write
Register Name
Bad Sync Detect
HSYNCs per
VSYNC MSB
HSYNCs per
VSYNC
Clamp Placement
Clamp Duration
Red Clamp Select
[0]
*******0
Hold Auto-Offset
[7]
0*******
Auto-Offset
Enable
[6:5]
*10*****
Auto-Offset
Update Mode
[4:3]
***01***
Difference Shift
Amount
[2]
*****1**
Auto Jump Enable
[1]
******1*
Post Filter Enable
[0]
*******0
Toggle Filter
Enable
Slew Limit
Sync Filter Lock
Threshold
Sync Filter Unlock
Threshold
Sync Filter
Window Width
0x1D
0x1E
Read/Write
Read/Write
[7:0]
[7:0]
00001000
32
0x1F
Read/Write
[7:0]
50
0x20
Read/Write
[7:0]
50
Description
0 = not detected.
1 = detected.
MSB of HSYNCs per VSYNC.
HSYNCs per VSYNC count.
Number of pixel clocks after trailing edge of HSYNC to begin clamp.
Number of pixel clocks to clamp.
0 = clamp to ground.
1 = clamp to midscale.
0 = clamp to ground.
1 = clamp to midscale.
0 = clamp to ground.
1 = clamp to midscale.
0 = don’t clamp during coast.
1 = clamp during coast.
0 = internal clamp enabled.
1 = internal clamp disabled.
0 = low bandwidth.
1 = full bandwidth.
0 = normal auto-offset operation.
1 = hold current offset value.
0 = manual offset.
1 = auto-offset using offset as target code.
00 = every clamp.
01 = every 16 clamps.
10 = every 64 clamps.
11 = every VSYNC.
00 = 100% of difference used to calculate new offset.
01 = 50%.
10 = 25%.
11 = 12.5%.
0 = normal operation.
1 = if code > 15 codes off, offset is jumped to the predicted offset
necessary to fix the >15 code mismatch.
0 = disable post filer.
1 = enable post filter.
Post filter reduces update rate by 1/6 and requires that all six
updates recommend a change before changing the offset. This
prevents unwanted offset changes.
The toggle filter looks for the offset to toggle back and forth and
holds it if triggered. This prevents toggling in case of missing codes
in the PGA.
Limits the amount the offset can change by in a single update.
Number of clean HSYNCs required for sync filter to lock.
Number of missing HSYNCs required to unlock the sync filter. Counter
counts up if HSYNC pulse is missing and down for a good HSYNC.
Width of the window in which HSYNC pulses are allowed.
Rev. 0 | Page 23 of 48
AD9396
Hex
Address
0x21
Read/Write
or Read Only
Read/Write
Bits
[7]
Default
Value
1*******
[6]
*1******
[5]
**0*****
VSYNC Filter
Enable
[4]
***0****
[3]
**** 1***
VSYNC Duration
Enable
Auto-Offset
Clamp Mode
[2]
**** *1**
Register Name
SP Sync Filter
Enable
PLL Sync Filter
Enable
Auto-Offset
Clamp Length
0x22
0x23
Read/Write
Read/Write
[7:0]
[7:0]
4
32
VSYNC Duration
HSYNC Duration
0x24
Read/Write
[7]
1*******
HSYNC Output
Polarity
[6]
*1******
VSYNC Output
Polarity
[5]
[4]
[3]
[2:1]
0x25
Read/Write
**1*****
***1****
****1***
*****11*
DE Output
Polarity
Field Output
Polarity
SOG Output
Polarity
SOG Output
Select
[0]
*******0
Output CLK Invert
[7:6]
01******
Output CLK Select
[5:4]
**11****
Output Drive
Strength
Description
Enables coast, VSYNC duration, and VSYNC filter to use the
regenerated HSYNC rather than the raw HSYNC.
Enables the PLL to use the filtered HSYNC rather than the raw
HSYNC. This clips any bad HSYNCs, but does not regenerate missing
pulses.
Enables the VSYNC filter. The VSYNC filter gives a predictable
HSYNC/VSYNC timing relationship but clips one HSYNC period off
the leading edge of VSYNC.
Enables the VSYNC duration block. This block can be used if
necessary to restore the duration of a filtered VSYNC.
0 = auto-offset measures code during clamp.
1 = auto-offset measures code (10 or 16) clock cycles after end of
clamp for 6 clock cycles.
Sets delay after end of clamp for auto-offset clamp mode = 1.
0 = delay is 10 clock cycles.
1 = delay is 16 clock cycles.
VSYNC duration.
HSYNC duration. Sets the duration of the output HSYNC in pixel
clocks.
Output HSYNC polarity (both DVI and analog). 0 = active low out.
1 = active high out.
Output VSYNC polarity (both DVI and analog).
0 = active low out.
1 = active high out.
Output DE polarity (both DVI and analog).
0 = active low out.
1 = active high out.
Output field polarity (both DVI and analog).
0 = active low out.
1 = active high out.
Output SOG polarity (analog only).
0 = active low out.
1 = active high out.
Selects signal present on SOG output.
00 = SOG (SOG0 or SOG1).
01 = raw HSYNC (HSYNC0 or HSYNC1).
10 = regenerated sync.
11 = HSYNC to PLL.
0 = don’t invert clock out.
1 = invert clock out.
Selects which clock to use on output pin. 1× CLK is divided down
from TMDS clock input when pixel repetition is in use.
00 = ½× CLK.
01 = 1× CLK.
10 = 2× CLK.
11 = 90° phase 1× CLK.
Sets the drive strength of the outputs.
00 = lowest, 11 = highest.
Rev. 0 | Page 24 of 48
AD9396
Hex
Address
0x26
Read/Write
or Read Only
Read/Write
Bits
[3:2]
Default
Value
****00**
[1]
******1*
[0]
*******0
[7]
0*******
[6]
[3]
*0******
****1***
[2:1]
0x27
Read/Write
*****00*
Register Name
Output Mode
Primary Output
Enable
Secondary
Output Enable
Output ThreeState
SOG Three-State
Power-Down Pin
Polarity
Power-Down Pin
Function
[0]
*******0
Power-Down
[7]
1*******
Auto PowerDown Enable
[6]
*0******
HDCP A0
[4]
[3]
***0****
****0***
[2:0]
*****000
BT656 EN
Force DE
Generation
Interlace Offset
0x28
Read/Write
[7:2]
011000**
VS Delay
0x29
Read/Write
[1:0]
[7:0]
******01
00000100
HS Delay MSB
HS Delay
0x2A
0x2B
0x2C
Read/Write
Read/Write
Read/Write
[3:0]
[7:0]
[3:0]
****0101
00000000
****0010
0x2D
0x2E
0x2F
Read/Write
Read/Write
Read
[7:0]
[7]
[6]
11010000
0*******
*0******
[5]
[3]
[2:0]
**0*****
****0***
*****000
Line Width MSB
Line Width
Screen Height
MSB
Screen Height
Test 1
TMDS Sync
Detect
TMDS Active
HDCP Keys Read
DVI Quality
Description
Selects which pins the data comes out on.
00 = 4:4:4 mode (normal).
01 = 4:2:2 + DDR 4:2:2 on blue.
10 = DDR 4:4:4 + DDR 4:2:2 on blue.
Enables primary output.
Enables secondary output (DDR 4:2:2 in Output Mode 1 and
Mode 2).
Three-states the outputs.
Three-states the SOG output.
Sets polarity of power-down pin.
0 = active low.
1 = active high.
Selects the function of the power-down pin.
00 = power-down.
01 = power-down and three-state SOG.
10 = three-state outputs only.
11 = three-state outputs and SOG.
0 = normal.
1 = power-down.
0 = disable auto low power state.
1 = enable auto low power state.
Sets the LSB of the address of the HDCP I2C. Set to 1 only for a
second receiver in a dual-link configuration.
0 = use internally generated MCLK.
1 = use external MCLK input.
Enables EAV/SAV codes to be inserted into the video output data.
Allows use of the internal DE generator in DVI mode.
Sets the difference (in HSYNCs) in field length between Field 0 and
Field 1.
Sets the delay (in lines) from VSYNC leading edge to the start of
active video.
MSB, Register 0x29.
Sets the delay (in pixels) from HSYNC leading edge to the start of
active video.
MSB, Register 0x2B.
Sets the width of the active video line (in pixels).
MSB, Register 0x2D.
Sets the height of the active screen (in lines).
Must be written to 1 for proper operation.
Detects a TMDS DE.
Detects a TMDS clock.
Returns 1 when read of EEPROM keys is successful.
Returns quality number based on DE edges.
Rev. 0 | Page 25 of 48
AD9396
Hex
Address
0x30
0x31
0x32
0x33
0x34
0x35
Read/Write
or Read Only
Read
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Bits
[6]
Default
Value
*0******
[5]
**0*****
[4]
***0****
[7:4]
1001****
DVI HSYNC
Polarity
DVI VSYNC
Polarity
MV Pulse Max
[3:0]
****0110
MV Pulse Min
[7]
0*******
[6]
[5:0]
*0******
**001101
[7]
1*******
MV Oversample
En
MV Pal En
MV Line Count
Start
MV Detect Mode
[6]
*0******
Register Name
DVI Content
Encrypted
MV Settings
Override
[5:0]
**010101
[7:6]
10******
[5]
**0*****
[4]
***0****
[3]
****0***
[2]
[1]
*****0**
******0*
CrCb Filter Enable
CSC_Enable
[6:5]
*01* ****
CSC_Mode
[4:0]
***01100
CSC_Coeff_A1
MSB
CSC_Coeff_A1
0x36
Read/Write
[7:0]
01010010
0x37
Read/Write
[4:0]
***01000
0x38
Read/Write
[7:0]
00000000
MV Line Count
End
MV Pulse Limit
Set
Low Freq Mode
Low Freq
Override
Up Conversion
Mode
Description
This bit is high when HDCP decryption is in use (content is
protected). The signal goes low when HDCP is not being used.
Customers can use this bit to determine whether to allow copying
of the content. The bit should be sampled at regular intervals
because it can change on a frame by frame basis.
Returns DVI HSYNC polarity.
Returns DVI VSYNC polarity.
Sets the maximum pseudo sync pulse width for Macrovision
detection.
Sets the minimum pseudo sync pulse width for Macrovision
detection.
Tells the Macrovision detection engine whether oversampling is in
use.
Tells the Macrovision detection engine to enter PAL mode.
Sets the start line for Macrovision detection.
0 = standard definition.
1 = progressive scan mode.
0 = use hard coded settings for line counts and pulse widths.
1 = use I2C values for these settings.
Sets the end line for Macrovision detection.
Sets the number of pulses required in the last 3 lines (SD mode
only).
Sets whether the Audio PLL is in low frequency mode. Low
frequency mode should only be set for pixel clocks <80 MHz.
Allows the previous bit to be used to set low frequency mode
rather than the internal auto-detect.
0 = repeat Cr and Cb values.
1 = interpolate Cr and Cb values.
Enables the FIR filter for 4:2:2 CrCb output.
Enables the color space converter (CSC). The default settings for the
CSC provide HDTV-to-RGB conversion.
Sets the fixed point position of the CSC coefficients, including the
A4, B4, and C4 offsets.
00 = ±1.0, −4096 to +4095.
01 = ±2.0, −8192 to +8190.
1× = ±4.0, −16384 to +16380.
MSB, Register 0x36.
Color space converter (CSC) coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x38.
B
CSC_Coeff_A2
MSB
CSC_Coeff_A2 LSB
CSC coefficient for equation:
ROUT = (A1 × RIN + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
B
Rev. 0 | Page 26 of 48
AD9396
Hex
Address
0x39
Read/Write
or Read Only
Read/Write
Bits
[4:0]
Default
Value
***00000
0x3A
Read/Write
[7:0]
00000000
0x3B
Read/Write
[4:0]
***11001
0x3C
Read/Write
[7:0]
11010111
CSC_Coeff_A4
MSB
CSC_Coeff_A4 LSB
0x3D
0x3E
Read/Write
Read/Write
[4:0]
[7:0]
***11100
01010100
CSC_Coeff_B1 MSB
CSC_Coeff_B1 LSB
0x3F
0x40
Read/Write
Read/Write
[4:0]
[7:0]
***01000
00000000
CSC_Coeff_B2 MSB
CSC_Coeff_B2 LSB
0x41
0x42
Read/Write
Read/Write
[4:0]
[7:0]
***11110
10001001
CSC_Coeff_B3 MSB
CSC_Coeff_B3 LSB
0x43
0x44
Read/Write
Read/Write
[4:0]
[7:0]
***00010
10010010
CSC_Coeff_B4 MSB
CSC_Coeff_B4 LSB
Register Name
CSC_Coeff_A3
MSB
CSC_Coeff_A3 LSB
Description
MSB, Register 0x3A.
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x3C.
B
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x3E.
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x40.
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x42.
CSC coefficient for equation:
ROUT = (A1 × RIN + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x44.
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × RIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x46.
B
B
B
B
B
0x45
Read/Write
[4:0]
***00000
0x46
Read/Write
[7:0]
00000000
CSC_Coeff_C1
MSB
CSC_Coeff_C1 LSB
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x48.
B
0x47
Read/Write
[4:0]
***01000
0x48
Read/Write
[7:0]
00000000
CSC_Coeff_C2
MSB
CSC_Coeff_C2
LSB
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
MSB, Register 0x4A.
B
0x49
Read/Write
[4:0]
***01110
0x4A
Read/Write
[7:0]
10000111
CSC_Coeff_C3
MSB
CSC_Coeff_C3
LSB
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
B
Rev. 0 | Page 27 of 48
AD9396
Hex
Address
0x4B
Read/Write
or Read Only
Read/Write
Bits
[4:0]
Default
Value
***11000
0x4C
Read/Write
[7:0]
10111101
Register Name
CSC_Coeff_C4
MSB
CSC_Coeff_C4
LSB
Description
MSB, Register 0x4C.
CSC coefficient for equation:
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
Must be written to 0x20 for proper operation.
Must be written to default 0x0F for proper operation.
This disables the MDA/MCL pull-ups.
Clock termination power-down override: 0 = auto, 1 = manual.
Clock termination: 0 = normal, 1 = disconnected.
This bit three-states the MDA/MCL lines.
B
0x50
0x56
0x59
Read/Write
Read/Write
Read/Write
[7:0]
[7:0]
[6]
[5]
[4]
[0]
00100000
00001111
MDA/MCL PU
CLK Term O/R
Manual CLK Term
MDA/MCL ThreeState
Rev. 0 | Page 28 of 48
AD9396
2-WIRE SERIAL CONTROL REGISTER DETAILS
CHIP IDENTIFICATION
CLOCK GENERATOR CONTROL
0x00—Bits[7:0] Chip Revision
0x03—Bits[7:6] VCO Range Select
An 8-bit value that reflects the current chip revision.
Two bits that establish the operating range of the clock
generator. VCORNGE must be set to correspond with the
desired operating frequency (incoming pixel rate). The PLL
gives the best jitter performance at high frequencies. For this
reason, to output low pixel rates and still get good jitter
performance, the PLL actually operates at a higher frequency
but then divides down the clock rate. Table 13 shows the pixel
rates for each VCO range setting. The PLL output divisor is
automatically selected with the VCO range setting.
PLL DIVIDER CONTROL
0x01—Bits[7:0] PLL Divide Ratio MSBs
The eight most significant bits of the 12-bit PLL divide ratio
PLLDIV.
The PLL derives a pixel clock from the incoming HSYNC
signal. The pixel clock frequency is then divided by an integer
value such that the output is phase locked to HSYNC. This
PLLDIV value determines the number of pixel times (pixels
plus horizontal blanking overhead) per line. This is typically
20% to 30% more than the number of active pixels in the
display.
The 12-bit value of the PLL divider supports divide ratios from
221 to 4095. The higher the value loaded in this register, the
higher the resulting clock frequency with respect to a fixed
HSYNC frequency.
VESA has established some standard timing specifications,
which assists in determining the value for PLLDIV as a function
of horizontal and vertical display resolution and frame rate
(see Table 9).
However, many computer systems do not conform precisely to
the recommendations, and these numbers should be used only
as a guide. The display system manufacturer should provide
automatic or manual means for optimizing PLLDIV. An
incorrectly set PLLDIV usually produces one or more vertical
noise bars on the display. The greater the error, the greater the
number of bars produced.
Table 13. VCO Ranges
VCO Range
00
01
10
11
Pixel Rate Range
12 to 30
30 to 60
60 to 120
120 to 150
The power-up default value is 01.
Bits[5:3] Charge Pump Current
Three bits that establish the current driving the loop filter in the
clock generator.
Table 14. Charge Pump Currents
Ip2
0
0
0
0
1
1
1
1
Ip1
0
0
1
1
0
0
1
1
Ip0
0
1
0
1
0
1
0
1
Current (μA)
50
100
150
250
350
500
750
1500
The power-up default value of PLLDIV is 1693 (PLLDIVM =
0x69, PLLDIVL = 0xDx).
The power-up default value is current = 001.
The AD9396 updates the full divide ratio only when the LSBs
are changed. Writing to this register by itself does not trigger an
update.
This bit determines the source of the pixel clock.
0x02—Bits[7:4] PLL Divide Ratio LSBs
The four least significant bits of the 12-bit PLL divide ratio
PLLDIV.
The power-up default value of PLLDIV is 1693 (PLLDIVM =
0x69, PLLDIVL = 0xDx).
Bit[2] External Clock Enable
A Logic 0 enables the internal PLL that generates the pixel clock
from an externally provided HSYNC.
A Logic 1 enables the external CKEXT input pin. In this mode,
the PLL divide ratio (PLLDIV) is ignored. The clock phase
adjusts (phase is still functional). The power-up default value is
EXTCLK = 0.
0x04—Bits[7:3] Phase Adjust
These bits provide a phase adjustment for the DLL to generate
the ADC clock, a 5-bit value that adjusts the sampling phase in
32 steps across one pixel time. Each step represents an 11.25°
shift in sampling phase. The power-up default is 16.
Rev. 0 | Page 29 of 48
AD9396
INPUT GAIN
0x0A—Bits[7:0] Green Channel Offset Adjust
0x05—Bits[7:0] Red Channel Gain
If clamp feedback is enabled, the 8-bit offset adjust determines
the clamp code. The 8-bit offset adjust is a twos complement
number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 =
0, 0xFF = −1, and 0x80 = −128). For example, if the register is
programmed to 130d, then the output code is equal to 130d at
the end of the clamp period. Note that incrementing the offset
register setting by 1 LSB adds 1 LSB of offset, regardless of the
clamp feedback setting. The power-up default is 0.
These bits control the programmable gain amplifier (PGA) of
the red channel. The AD9396 can accommodate input signals
with a full-scale range of between 0.5 V p-p and 1.0 V p-p.
Setting the red gain to 255 corresponds to an input range of
1.0 V. A red gain of 0 establishes an input range of 0.5 V. Note
that increasing red gain results in the picture having less
contrast (the input signal uses fewer of the available converter
codes). The power-up default is 0x80.
0x06—Bits[7:0] Green Channel Gain
These bits control the PGA of the green channel. The AD9396
can accommodate input signals with a full-scale range of
between 0.5 V p-p and 1.0 V p-p. Setting the green gain to
255 corresponds to an input range of 1.0 V. A green gain of
0 establishes an input range of 0.5 V. Note that increasing green
gain results in the picture having less contrast (the input signal
uses fewer of the available converter codes). The power-up
default is 0x80.
0x07—Bits[7:0] Blue Channel Gain
These bits control the PGA of the blue channel. The AD9396
can accommodate input signals with a full-scale range of
between 0.5 V and 1.0 V p-p. Setting the blue gain to 255
corresponds to an input range of 1.0 V. A blue gain of 0
establishes an input range of 0.5 V. Note that increasing blue
gain results in the picture having less contrast (the input signal
uses fewer of the available converter codes). The power-up
default is 0x80.
INPUT OFFSET
0x08—Bits[7:0] Red Channel Offset Adjust
If clamp feedback is enabled, the 8-bit offset adjust determines
the clamp code. The 8-bit offset adjust is a twos complement
number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 =
0, 0xFF = −1, and 0x80 = −128). For example, if the register is
programmed to 130d, then the output code is equal to 130d at
the end of the clamp period. Note that incrementing the offset
register setting by 1 LSB adds 1 LSB of offset, regardless of the
clamp feedback setting. The power-up default is 0.
0x09—Bits[7:0] Red Channel Offset
These eight bits are the red channel offset control. The offset
control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on
whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1).
If clamp feedback is disabled, the offset register bits control the
absolute offset added to the channel. The offset control provides
+127/−128 LSBs of adjustment range, with 1 LSB of offset
corresponding to 1 LSB of output code. If clamp feedback is
enabled these bits provide the relative offset (brightness) from
the offset adjust in the previous register. The power-up default
is 0x80.
0x0B—Bits[7:0] Green Channel Offset
These eight bits are the green channel offset control. The offset
control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on
whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1).
If clamp feedback is disabled, the offset register bits control the
absolute offset added to the channel. The offset control provides
an adjustment range of +127/−128 LSBs, with one LSB of offset
corresponding to 1 LSB of output code. If clamp feedback is
enabled, these bits provide the relative offset (brightness) from
the offset adjust in the previous register. The power-up default
is 0x80.
0x0C—Bits[7:0] Blue Channel Offset Adjust
If clamp feedback is enabled, the 8-bit offset adjust determines
the clamp code. The 8-bit offset adjust is a twos complement
number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 =
0, 0xFF = −1, and 0x80 = −128). For example, if the register is
programmed to 130d, then the output code is equal to 130d at
the end of the clamp period. Note that incrementing the offset
register setting by 1 LSB adds 1 LSB of offset, regardless of the
clamp feedback setting. The power-up default is 0.
0x0D—Bits[7:0] Blue Channel Offset
These eight bits are the blue channel offset control. The offset
control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on
whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1).
If clamp feedback is disabled, the offset register bits control the
absolute offset added to the channel. The offset control provides
an adjustment range of +127/−128 LSBs, with 1 LSB of offset
corresponding to 1 LSB of output code. If clamp feedback is
enabled, these bits provide the relative offset (brightness) from
the offset adjust in the previous register. The power-up default
is 0x80.
SYNC
0x0E—Bits[7:0] Sync Separator
Selects the maximum HSYNC pulse width for composite sync
separation. Power-down default is 0x20.
0x0F—Bits[7:2] SOG Comparator Threshold Enter
The enter level for the SOG slicer. Must be < the exit level
(Register 0x10). The power-up default is 0x10.
Rev. 0 | Page 30 of 48
AD9396
0x10—Bits[7:2] SOG Comparator Threshold Exit
0x12—Bit[4] VSYNC Polarity Override
The exit level for the SOG slicer. Must be > the enter level
(Register 0x0F). The power-up default is 0x10.
0 = auto VSYNC polarity, 1 = manual VSYNC polarity. Manual
VSYNC polarity is defined in Register 0x11, Bit 5. The powerup default is 0.
0x11—Bit[7] HSYNC Source
0 = HSYNC, 1 = SOG. The power-up default is 0. These
selections are ignored if Register 0x11, Bit 6 = 0.
COAST AND CLAMP CONTROLS
0x11—Bit[6] HSYNC Source Override
0 = active low, 1 = active high. The power-up default
is 1.
0x12—Bit[3] Input Coast Polarity
0 = auto HSYNC source, 1 = manual HSYNC source. Manual
HSYNC source is defined in Register 0x11, Bit 7. The power-up
default is 0.
0x11—Bit[5] VSYNC Source
0x12—Bit[2] Coast Polarity Override
0 = auto-coast polarity, 1 = manual coast polarity. The powerup default is 0.
0 = VSYNC, 1 = VSYNC from SOG. The power-up default is 0.
These selections are ignored if Register 0x11, Bit 4 = 0.
0x12—Bit[1] Coast Source
0x11—Bit[4] VSYNC Source Override
0x12—Bit[0] Filter Coast VSYNC
0 = auto VSYNC source, 1 = manual VSYNC source. Manual
VSYNC source is defined in Register 0x11, Bit 5. The power-up
default is 0.
0 = use raw VSYNC for coast generation, 1 = use filtered
VSYNC for coast generation The power-up default is 1.
0 = internal coast, 1 = external coast. The power-up default is 0.
0x13—Bits[7:0] Precoast
0x11—Bit[3] Channel Select
0 = Channel 0, 1 = Channel 1. The power-up default is 0. These
selections are ignored if Register 0x11, Bit 2 = 0.
0x11—Bit[2] Channel Select Override
0 = auto channel select, 1 = manual channel select. Manual
channel select is defined in Register 0x11, Bit 3. The power-up
default is 0.
This register allows the internally generated coast signal to be
applied prior to the VSYNC signal. This is necessary in cases
where pre-equalization pulses are present. The step size for this
control is one HSYNC period. For precoast to work correctly, it
is necessary for the VSYNC filter (0x21, Bit 5) and sync
processing filter (0x21 Bit 7) both to be either enabled or
disabled. The power-up default is 0.
0x14—Bits[7:0] Postcoast
0x11—Bit[1] Interface Select
0 = analog interface, 1 = digital interface. The power-up default
is 0. These selections are ignored if Register 0x11, Bit 0 = 0.
0x11—Bit[0] Interface Select Override
0 = auto interface select, 1 = manual interface select. Manual
interface select is defined in Register 0x11, Bit 1. The power-up
default is 0.
This register allows the internally generated coast signal to be
applied following the VSYNC signal. This is necessary in cases
where postequalization pulses are present. The step size for this
control is one HSYNC period. For postcoast to work correctly,
it is necessary for the VSYNC filter (0x21, Bit 5) and sync
processing filter (0x21, Bit 7) both to be either enabled or
disabled. The power-up default is 0.
STATUS OF DETECTED SIGNALS
0x12—Bit[7] Input HSYNC Polarity
0 = active low, 1 = active high. The power-up default is 1. These
selections are ignored if Register 10x2, Bit 6 = 0.
0x12—Bit[6] HSYNC Polarity Override
0 = auto HSYNC polarity, 1 = manual HSYNC polarity. Manual
HSYNC polarity is defined in Register 0x11,
Bit 7. The power-up default is 0.
0x12—Bit[5] Input VSYNC Polarity
0 = active low, 1 = active high. The power-up default is 1. These
selections are ignored if Register 0x11,Bit 4 = 0.
0x15—Bit[7] HSYNC0 Detection Bit
Indicates if HSYNC0 is active. This bit is used to indicate when
activity is detected on the HSYNC0 input pin. If HSYNC is held
high or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 =
HSYNC0 not active. 1 = HSYNC0 is active.
0x15—Bit[6] HSYNC1 Detection Bit
Indicates if HSYNC1 is active. This bit is used to indicate when
activity is detected on the HSYNC1 input pin. If HSYNC is held
high or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 =
HSYNC1 not active. 1 = HSYNC1 is active.
Rev. 0 | Page 31 of 48
AD9396
0x15—Bit[5] VSYNC0 Detection Bit
Indicates if VSYNC0 is active. This bit is used to indicate when
activity is detected on the VSYNC0 input pin. If VSYNC is held
high or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 =
VSYNC0 not active. 1 = VSYNC0 is active.
0x15—Bit[4] VSYNC1 Detection Bit
0x16—Bit[2] Pseudo Sync Detected
0x16—Bit[1] Sync Filter Locked
Indicates whether sync filter is locked to periodic sync signals.
0 = sync filter locked to periodic sync signal. 1 = sync filter not
locked.
0x16—Bit[0] Bad Sync Detect
0x17—Bits[3:0] HSYNCs per VSYNC MSBs
Indicates if VSYNC1 is active. This bit is used to indicate when
activity is detected on the VSYNC1 input pin. If VSYNC is held
high or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 =
VSYNC1 not active. 1 = VSYNC1 is active.
The 4 MSBs of the 12-bit counter that reports the number of
HSYNCs/VSYNC on the active input. This is useful in
determining the mode and aids in setting the PLL divide ratio.
0x15—Bit[3] SOG0 Detection Bit
The 8 LSBs of the 12-bit counter that reports the number of
HSYNCs/VSYNC on the active input.
Indicates if SOG0 is active. This bit is used to indicate when
activity is detected on the SOG0 input pin. If SOG is held high
or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 = SOG0
not active. 1 = SOG0 is active.
0x18—Bits[7:0] HSYNCs per VSYNC LSBs
0x19—Bits[7:0] Clamp Placement
Number of pixel clocks after the trailing edge of HSYNC to
begin clamp. The power-up default is 8.
0x1A—Bits[7:0] Clamp Duration
0x15—Bit[2] SOG1 Detection Bit
Number of pixel clocks to clamp. The power-up default is 0x14.
Indicates if SOG1 is active. This bit is used to indicate when
activity is detected on the SOG1 input pin. If SOG is held high
or low, activity is not detected. The sync processing block
diagram shows where this function is implemented. 0 = SOG1
not active. 1 = SOG1 is active.
0x15—Bit[1] Coast Detection Bit
This bit detects activity on the EXTCLK/EXTCOAST pin. It
indicates that one of the two signals is active, but it doesn’t
indicate if it is EXTCLK or COAST. A dc signal is not detected.
0 = no activity detected. 1 = activity detected.
0x1B—Bits[7] Red Clamp Select
This bit selects whether the red channel is clamped to ground or
midscale. Ground clamping is used for red in RGB applications
and midscale clamping is used in YPrPb (YUV) applications.
0 = channel clamped to ground during clamping period. 1 =
channel clamped to midscale during clamping period. The
power-up default is 0.
0x1B—Bit[6] Green Clamp Select
Indicates the polarity of the HSYNC0 input. 0 = HSYNC
polarity negative. 1 = HSYNC polarity positive.
This bit selects whether the green channel is clamped to ground
or midscale. Ground clamping is normally used for green in
RGB applications and YPrPb (YUV) applications. 0 = channel
clamped to ground during clamping period. 1 = channel
clamped to midscale during clamping period. The power-up
default is 0.
0x16—Bit[6] HSYNC 1 Polarity
0x1B—Bit[5] Blue Clamp Select
Indicates the polarity of the HSYNC1 input. 0 = HSYNC
polarity negative. 1 = HSYNC polarity positive.
Indicates the polarity of the VSYNC0 input. 0 = VSYNC
polarity negative. 1 = VSYNC polarity positive.
This bit selects whether the blue channel is clamped to ground
or midscale. Ground clamping is used for blue in RGB
applications and midscale clamping is used in YPrPb (YUV)
applications. 0 = channel clamped to ground during clamping
period. 1 = channel clamped to midscale during clamping
period. The power-up default is 0.
0x16—Bit[4] VSYNC1 Polarity
0x1B—Bit[4] Clamp During Coast
Indicates the polarity of the VSYNC1 input. 0 = VSYNC
polarity negative. 1 = VSYNC polarity positive.
This bit permits clamping to be disabled during coast because
video signals are generally not at a known back porch or
midscale position during coast. 0 = clamping during coast is
disabled. Clamping during coast is enabled. The power-up
default is 0.
POLARITY STATUS
0x16—Bit[7] HSYNC 0 Polarity
0x16—Bit[5] VSYNC 0 Polarity
0x16—Bit[3] Coast Polarity
Indicates the polarity of the external coast signal. 0 = coast
polarity negative. 1 = coast polarity positive.
Rev. 0 | Page 32 of 48
AD9396
0x1B—Bit[3] Clamp Disable
0x1F—Bits[7:0] Sync Filter Unlock Threshold
0 = internal clamp enabled. 1 = internal clamp disabled. The
power-up default is 0.
This 8-bit register is programmed to set the number of missing
or invalid HSYNCs needed to unlock the sync filter. This
disables the filter operation when there is no longer a stable
HSYNC signal. The power-up default setting is 50d.
0x1B —Bits[2:1] Programmable Bandwidth
x0 = low bandwidth. x1 = high bandwidth. The power-up
default is 1.
0x20—Bits[7:0] Sync Filter Window Width
0 = manual offset. 1 = auto-offset using offset as target code.
The power-up default is 0.
This 8-bit register sets the distance in 40 MHz clock periods
(25 ns), which is the allowed distance for HSYNC pulses before
and after the expected HSYNC edge. This is the heart of the
filter in that it only looks for HSYNC pulses at a given time
(plus or minus this window) and then ignores extraneous
equalization pulses that disrupt accurate PLL operation. The
power-up default setting is 10d, or 200 ns on either side of the
expected HSYNC.
0x1C—Bits[6:5] Auto-Offset Update Mode
0x21—Bit[7] Sync Processing Filter Enable
00 = every clamp.
01 = every 16 clamps.
10 = every 64 clamps.
11 = every VSYNC.
The power-up default setting is 10.
This bit selects which HSYNC is used for the sync processing
functions of internal coast, H/V count, field detection, and
VSYNC duration counts. A clean HSYNC is fundamental to
accurate processing of the sync. 0 = sync processing uses raw
HSYNC or SOG. 1 = sync processing uses regenerated HSYNC
from sync filter. The power-up default setting is 1.
0x1B—Bit[0] Hold Auto-Offset
0 = normal auto-offset operation. 1 = hold current offset value.
The power-up default is 0.
0x1C—Bit[7] Auto-Offset Enable
0x1C—Bits[4:3] Difference Shift Amount
00 = 100% of difference used to calculate new offset.
01 = 50%.
10 = 25%.
11 = 12.5%.
The power-up default is 01.
0x21—Bit[6] PLL Sync Filter Enable
0x1C—Bit[2] Auto-Jump Enable
0 = normal operation. 1 = if the code >15 codes off, the offset is
jumped to the predicted offset necessary to fix the >15 code
mismatch. The power-up default is 1.
0x1C—Bit[1] Post Filter Enable
The post filter reduces the update rate by 1/6 and requires that
all six updates recommend a change before changing the offset.
This prevents unwanted offset changes. 0 = disable post filter.
1 = enable post filter. The power-up default is 1.
0x1C—Bit[0] Toggle Filter Enable
The toggle filter looks for the offset to toggle back and forth and
holds it if triggered. This is to prevent toggling in case of
missing codes in the PGA. 1 = toggle filter on. 0 = toggle filter
off. The power-up default is 0.
0x1D—Bits[7:0] Slew Limit
Limits the amount the offset can change in a single update. The
power-up default is 0x08.
This bit selects which signal the PLL uses. It can select between
raw HSYNC or SOG, or filtered versions. The filtering of the
HSYNC and SOG can eliminate nearly all extraneous
transitions which have traditionally caused PLL disruption. 0 =
PLL uses raw HSYNC or SOG inputs. 1 = PLL uses filtered
HSYNC or SOG inputs. The power-up default setting is 0.
0x21—Bit[5] VSYNC Filter Enable
The purpose of the VSYNC filter is to guarantee the position of
the VSYNC edge with respect to the HSYNC edge and to
generate a field signal. The filter works by examining the
placement of VSYNC and regenerating a correctly placed
VSYNC one line later. The VSYNC is first checked to see
whether it occurs in the Field 0 position or the Field 1 position.
This is done by checking the leading edge position against the
sync separator threshold and the HSYNC position. The HSYNC
width is divided into four quadrants with Quadrant 1 starting at
the HSYNC leading edge plus a sync separator threshold. If the
VSYNC leading edge occurs in Quadrant 1 or Quadrant 4, the
field is set to 0 and the output VSYNC is placed coincident with
the HSYNC leading edge. If the VSYNC leading edge occurs in
Quadrant 2 or Quadrant 3, the field is set to 1 and the output
VSYNC leading edge is placed in the center of the line. In this
way, the VSYNC filter creates a predictable relative position
between HSYNC and VSYNC edges at the output.
0x1E—Bits[7:0] Sync Filter Lock Threshold
This 8-bit register is programmed to set the number
of valid HSYNCs needed to lock the sync filter. This ensures
that a consistent, stable HSYNC is present before attempting to
filter. The power-up default setting is 32d.
Rev. 0 | Page 33 of 48
AD9396
If the VSYNC occurs near the HSYNC edge, this guarantees
that the VSYNC edge follows the HSYNC edge. This performs
filtering also in that it requires a minimum of 64 lines between
VSYNCs. The VSYNC filter cleans up extraneous pulses that
might occur on the VSYNC. This should be enabled whenever
the HSYNC/VSYNC count is used. Setting this bit to 0 disables
the VSYNC filter. Setting this bit to 1 enables the VSYNC filter.
Power-up default is 0.
0x24—Bit[5] Display Enable Output Polarity
This bit sets the polarity of the display enable (DE) for both
DVI and analog. 0 = DE output polarity is negative. 1 = DE
output polarity is positive. The power-up default is 1.
0x24—Bit[4] Field Output Polarity
This bit sets the polarity of the field output signal (both DVI
and analog) on Pin 21. 0 = active low out. 1 = active high out.
The power-up default is 1.
0x21—Bit[4] VSYNC Duration Enable
This enables the VSYNC duration block which is designed to be
used with the VSYNC filter. Setting the bit to 0 leaves the
VSYNC output duration unchanged; setting the bit to 1 sets the
VSYNC output duration based on Register 0x22. 0 = VSYNC
output duration unchanged. 1 = VSYNC output duration set by
0x22. The power-up default is 0.
0x21—Bit[3] Auto-Offset Clamp Mode
This bit specifies if the auto-offset measurement takes place
during clamp or 10 or 16 clocks afterward. The measurement
takes 6 clock cycles. 0 = auto-offset measurement takes place
during clamp period. 1 = auto-offset measurement is set by
0x21, Bit 2. Default= 1.
0x24—Bit[3] SOG Output Polarity
This bit sets the polarity of the SOGOUT signal (analog only).
0 = active low. 1 = active high. The power-up default setting is 1.
0x24—Bits[2:1] SOG Output Select
These register bits control the output on the SOGOUT pin.
Options are the raw SOG from the slicer (this is the
unprocessed SOG signal produced from the sync slicer), the
raw HSYNC, the regenerated sync from the sync filter, which
can generate missing syncs because of coasting, dropout, or the
filtered sync that excludes extraneous syncs not occurring
within the sync filter window.
Table 15. SOGOUT Polarity Settings
SOGOUT Select
00
01
10
11
0x21—Bit[2] Auto-Offset Clamp Length
This bit sets the delay following the end of the clamp period
for AO measurement. This bit is valid only if Register 0x21,
Bit 3 = 1. 0 = delay is 10 clock cycles. 1 = delay is 16 clock
cycles. Default = 1.
Function
Raw SOG from sync slicer (SOG0 or SOG1)
Raw HSYNC (HSYNC0 or HSYNC1)
Regenerated sync from sync filter
HSYNC to PLL
The power-up default setting is 11.
0x22—Bits[7:0] VSYNC Duration
This is used to set the output duration of the VSYNC, and is
designed to be used with the VSYNC filter. This is valid only if
Register 0x21, Bit 4 is set to 1. Power-up default is 4.
0x23—Bits[7:0] HSYNC Duration
An 8-bit register that sets the duration of the HSYNC output
pulse. The leading edge of the HSYNC output is triggered by
the internally generated, phase-adjusted PLL feedback clock.
The AD9396 then counts a number of pixel clocks equal to the
value in this register. This triggers the trailing edge of the
HSYNC output, which is also phase-adjusted. The power-up
default is 32.
0x24—Bit[7] HSYNC Output Polarity
This bit sets the polarity of the HSYNC output. Setting this bit
to 0 sets the HSYNC output to active low. Setting this bit to 1
sets the HSYNC output to active high. Power-up default setting
is 1.
0x24—Bit[0] Output Clock Invert
This bit allows inversion of the output clock as specified by
Register 0x25, Bit 7 to Bit 6. 0 = noninverted clock. 1 = inverted
clock. The power-up default setting is 0.
0x25—Bits[7:6] Output Clock Select
These bits select the clock output on the DATACLK pin. They
include 1/2× clock, a 2× clock, a 90° phase shifted clock or the
normal pixel clock. The power-up default setting is 01.
Table 16. Output Clock Select
Select
00
01
10
11
0x24—Bit[6] VSYNC Output Polarity
This bit sets the polarity of the VSYNC output (both DVI and
analog). Setting this bit to 0 sets the VSYNC output to active
low. Setting this bit to 1 sets the VSYNC output to active high.
Power-up default is 1.
Rev. 0 | Page 34 of 48
Result
½× pixel clock
1× pixel clock
2× pixel clock
90° phase 1× pixel clock
AD9396
0x25—Bits[5:4] Output Drive Strength
0x26—Bit[6] SOG Three-State
These two bits select the drive strength for all the high speed
digital outputs (except VSOUT, A0, and the O/E Field). Higher
drive strength results in faster rise times/fall times and makes it
easier to capture data. Lower drive strength results in slower
rise/fall times and helps to reduce EMI and digitally generated
power supply noise. The power-up default setting is 11.
When enabled, this bit allows the SOGOUT pin to be placed in
a high impedance state. 0 = normal SOG output. 1 = SOGOUT
pin is in high impedance mode. The power-up default setting
is 0.
Table 17. Output Drive Strength
Output Drive
00
01
10
11
Result
Low output drive strength
Medium low output drive strength
Medium high output drive strength
High output drive strength
0x26—Bit[3] Power-Down Polarity
This bit defines the polarity of the input power-down pin.
0 = power-down pin is active low. 1 = power-down pin is active
high. The power-up default setting is 1.
0x26—Bits[2:1] Power-Down Pin Function
These bits define the different operational modes of the powerdown pin. These bits are functional only when the power-down
pin is active; when it is not active, the part is powered up and
functioning. The power-up default setting is 00.
0x25—Bits[3:2] Output Mode
These bits choose between four options for the output mode,
one of which is exclusive to an HDMI input. 4:4:4 mode is
standard RGB; 4:2:2 mode is YCrCb, which reduces the number
of active output pins from 24 to 16; 4:4:4 is the double data rate
(DDR) output mode; and the data is RGB mode, but changes on
every clock edge. The power-up default setting is 00.
Table 19. Power Down Pin Function
Function
00
01
10
Table 18. Output Mode
Output
Mode
00
01
10
11
Result
4:4:4 RGB mode
4:2:2 YCrCb mode + DDR 4:2:2 on blue (secondary)
DDR 4:4:4: DDR mode + DDR 4:2:2 on blue
(secondary)
Result
The chip is powered down and all outputs except
SOGOUT are in high impedance mode.
The chip is powered down and all outputs are in
high impedance mode.
The chip remains powered up, but all outputs
except SOGOUT are in high impedance mode.
The chip remains powered up, but all outputs are
in high impedance mode.
0x26—Bit[0] Power-Down
This bit places the primary output in active or high impedance
mode. The primary output is designated when using either 4:2:2
or DDR 4:4:4. In these modes, the data on the red and green
output channels is the primary output, while the output data on
the blue channel (DDR YCrCb) is the secondary output. 0 =
primary output is in high impedance mode. 1 = primary output
is enabled. The power-up default setting is 1.
This bit is used to put the chip in power-down mode. In this
mode, the power dissipation is reduced to a fraction of the
typical power (see Table 1 for exact power dissipation). When in
power-down, the HSOUT, VSOUT, DATACK, and all 30 data
outputs are put into a high impedance state. Note that the
SOGOUT output is not put into high impedance. Circuit blocks
that continue to be active during power-down include the
voltage references, sync processing, sync detection, and the
serial register. These blocks facilitate a fast start-up from powerdown. 0 = normal operation. 1 = power-down. The power-up
default setting is 0.
0x25—Bit[0] Secondary Output Enable
0x27—Bit[7] Auto Power-Down Enable
This bit places the secondary output in active or high
impedance mode. The secondary output is designated when
using either 4:2:2 or DDR 4:4:4. In these modes the data on the
blue output channel is the secondary output, while the output
data on the red and green channels is the primary output.
Secondary output is always a DDR YCrCb data mode. 0 =
secondary output is in high impedance mode. 1 = secondary
output is enabled. The power-up default setting is 0.
This bit enables the chip to go into low power mode, or seek
mode if no sync inputs are detected. 0 = auto power-down
disabled. 1 = chip powers down if no sync inputs present. The
power-up default setting is 1.
0x25—Bit[1] Primary Output Enable
0x26—Bit[7] Output Three-State
0x27—Bit[6] HDCP A0 Address
This bit sets the LSB of the address of the HDCP I2C. This
should be set to 1 only for a second receiver in a dual-link
configuration. The power-up default is 0.
When enabled, this bit puts all outputs (except SOGOUT) in a
high impedance state. 0 = normal outputs. 1 = all outputs
(except SOGOUT) in high impedance mode. The power-up
default setting is 0.
Rev. 0 | Page 35 of 48
AD9396
BT656 GENERATION
0x2F—Bit[4] AV Mute
0x27—Bit[4] BT656 Enable
This read-only bit indicates the presence of AV mute based on
general control packets. 0 = AV not muted. 1 = AV muted.
This bit enables the output to be BT656-compatible with
defined start of active video (SAV) and end of active video
(EAV) controls to be inserted. These require specification of the
number of active lines, active pixels per line, and delays to place
these markers. 0 = disable BT656 video mode. 1 = enable BT656
video mode. The power-up default setting is 0.
0x2F—Bit[3] HDCP Keys Read
This read-only bit reports if the HDCP keys were read
successfully. 0 = failure to read HDCP keys. 1 = HDCP keys
read.
0x2F—Bits[2:0] DV I Quality
0x27—Bit[3] Force DE Generation
These read-only bits indicate a level of DVI quality based on the
DE (display enable) edges. A larger number indicates a higher
quality.
This bit allows the use of the internal DE generator in DVI
mode. 0 = internal DE generation disabled. 1 = force DE
generation via programmed registers. The power-up default
setting is 0.
0x30—Bit[5] DVI HSYNC Polarity
0x27—Bits[2:0] Interlace Offset
These bits define the offset in HSYNCs from Field 0 to Field 1.
The power-up default setting is 000.
This read-only bit indicates the polarity of the DVI HSYNC.
0 = DVI HSYNC polarity is low active. 1 = DVI HSYNC
polarity is high active
0x30—Bit[4] DVI VSYNC Polarity
0x28—Bits[7:2] VSYNC Delay
This read-only bit indicates the polarity of the DVI VSYNC.
0 = DVI VSYNC polarity is low active. 1 = DVI VSYNC polarity
is high active.
These bits set the delay (in lines) from the leading edge of
VSYNC to active video. The power-up default setting is 24.
0x28—Bits[1:0] HSYNC Delay MSBs
MACROVISION
These 2 bits along with the following 8 bits set the delay (in
pixels) from the HSYNC leading edge to the start of active
video. The power-up default setting is 0x104.
0x31—Bits[7:4] Macrovision Pulse Max
See the HSYNC Delay MSBs section.
These bits set the pseudo sync pulse width maximum for
Macrovision detection in pixel clocks. This is functional for
13.5 MHz SDTV or 27 MHz progressive scan. Power-up
default is 9.
0x2A—Bits[3:0] Line Width MSBs
0x31—Bits[3:0] Macrovision Pulse Min
These 4 bits along with the following 8 bits set the width of the
active video line (in pixels). The power-up default setting is
0x500.
These bits set the pseudo sync pulse width maximum for
Macrovision detection in pixel clocks. This is functional for
13.5 MHz SDTV or 27 MHz progressive scan. Power-up
default is 6.
0x29—Bits[7:0] HSYNC Delay LSBs
0x2B—Bits[7:0] Line Width LSBs
0x32—Bit[7] Macrovision Oversample Enable
See the line width MSBs section.
0x2C—Bits[3:0] Screen Height MSBs
Along with the 8 bits following these 12 bits, set the height of
the active screen (in lines). The power-up default setting is
0x2D0.
0x2D—Bits[7:0] Screen Height LSBs
Tells the Macrovision detection engine whether oversampling
is used. This accommodates 27 MHz sampling for SDTV and
54 MHz sampling for progressive scan and is used as a
correction factor for clock counts. Power-up default is 0.
0x32—Bit[6] Macrovision PAL Enable
See the Screen Height MSBs section.
Tells the Macrovision detection engine to enter PAL mode when
set to 1. Default is 0 for NTSC mode.
0x2F—Bit[6] TMDS Sync Detect
0x32—Bits[5:0] Macrovision Line Count Start
This read-only bit indicates the presence of a TMDS DE. 0 = no
TMDS DE present. 1 = TMDS DE detected.
Set the start line for Macrovision detection. Along with Register
0x33, Bits [5:0] they define the region where MV pulses are
expected to occur. The power-up default is Line 13.
0x2F—Bit[5] TMDS Active
This read-only bit indicates the presence of a TMDS clock. 0 =
no TMDS clock present. 1 = TMDS clock detected.
0x33—Bit[7] Macrovision Detect Mode
0 = standard definition. 1 = progressive scan mode
Rev. 0 | Page 36 of 48
AD9396
0x35—Bits[4:0] Color Space Conversion Coefficient
A1 MSBs
0x33—Bit[6] Macrovision Settings Override
This defines whether preset values are used for the MV line
counts and pulse widths or the values stored in I2C registers.
0 = use hard-coded settings for line counts and pulse widths
1 = use I2C values for these settings
These 5 bits form the 5 MSBs of the Color space Conversion
Coefficient A1. This combined with the 8 LSBs of the following
register form a 13-bit, twos complement coefficient which is
user programmable. The equation takes the form of:
0x33—Bits[5:0] Macrovision Line Count End
Set the end line for Macrovision detection. Along with
Register 0x32, Bits [5:0] they define the region where MV
pulses are expected to occur. The power-up default is Line 21.
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
The default value for the 13-bit, A1 coefficient is 0x0C52.
0x34—Bits[7:6] Macrovision Pulse Limit Select
Set the number of pulses required in the last three lines (SD
mode only). If there is not at least this number of MV pulses,
the engine stops. These 2 bits define the following pulse counts:
0x36—Bits[7:0] Color Space Conversion Coefficient
A1 LSBs
See the Register 0x35 section.
0x37—Bits[4:0] CSC A2 MSBs
00 = 6
01 = 4
10 = 5 (default)
11 = 7
These five bits form the 5 MSBs of the Color space Conversion
Coefficient A2. Combined with the 8 LSBs of the following
register, they form a 13-bit, twos complement coefficient that is
user programmable. The equation takes the form of:
0x34—Bit[5] Low Frequency Mode
Sets whether the audio PLL is in low frequency mode. Low
frequency mode should only be set for pixel clocks < 80 MHz.
ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4
GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4
BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4
0x34—Bit[4] Low Frequency Override
Allows the previous bit to be used to set low frequency mode
rather than the internal autodetect.
The default value for the 13-bit A2 coefficient is 0x0800.
0x38—Bits[7:0] CSC A2 LSBs
0x34—Bit[3] Up Conversion Mode
See the Register 0x37 section.
0 = repeat Cb/Cr values
1 = interpolate Cb/Cr values
0x39—Bits[4:0] CSC A3 MSBs
The default value for the 13-bit A3 is 0x0000.
0x34—Bit[2] CbCr Filter Enable
Enables the FIR filter for 4:2:2 CbCr output.
0x3A—Bits[7:0] CSC A3 LSBs
0x3B—Bits[4:0] CSC A4 MSBs
COLOR SPACE CONVERSION
The default value for the 13-bit A4 is 0x19D7.
The default power up values for the color space converter
coefficients (R0x35 through R0x4C) are set for ATSC RGB to
YCbCr conversion. They are completely programmable for
other conversions.
0x3C—Bits[7:0] CSC A4 LSBs
0x3D—Bits[4:0] CSC B1 MSBs
0x34—Bit[1] Color Space Converter Enable
0x3E—Bits[7:0] CSC B1 LSBs
0x3F—Bits[4:0] CSC B2 MSB
This bit enables the color space converter. 0 = disable color
space converter. 1 = enable color space converter. The power-up
default setting is 0.
0x35—Bits[6:5] Color Space Converter Mode
These two bits set the fixed point position of the CSC
coefficients, including the A4, B4, and C4 offsets. Default = 01.
Table 20. CSC Fixed Point Converter Mode
Select
00
01
1×
Result
±1.0, −4096 to +4095
±2.0, −8192 to +8190
±4.0, −16384 to +16380
The default value for the 13-bit B1 is 0x1C54.
The default value for the 13-bit B2 is 0x0800.
0x40—Bits[7:0] CSC B2 LSBs
0x41—Bits[4:0] CSC B3 MSBs
The default value for the 13-bit B3 is 0x1E89.
0x42—Bits[7:0] CSC B3 LSBs
0x43—Bits[4:0] CSC B4 MSBs
The default value for the 13-bit B4 is 0x0291.
Rev. 0 | Page 37 of 48
AD9396
0x44—Bits[7:0] CSC B4 LSBs
0x45—Bits[4:0] CSC C1 MSBs
The default value for the 13-bit C1 is 0x0000.
0x46—Bits[7:0 CSC C1 LSBs
0x47—Bits[4:0 CSC C2 MSBs
The default value for the 13-bit C2 is 0x0800.
0x59—Bit[5] CLK Term O/R
This bit allows for overriding during power down.
0 = auto, 1 = manual.
0x59—Bit[4] Manual CLK Term
This bit allows normal clock termination or disconnects it. 0 =
normal, 1 = disconnected.
0x48—Bits[7:0] CSC C2 LSBs
0x49—Bits[4:0] CSC C3 MSBs
0x59—Bit[2] FIFO Reset UF
The default value for the 13-bit C3 is 0x0E87.
0x59—Bit[1] FIFO Reset OF
0x4A—Bits[7:0] CSC C3 LSBs
0x4B—Bits[4:0] CSC C4 MSBs
This bit resets the audio FIFO if overflow is detected.
The default value for the 13-bit C4 is 0x18BD.
This bit three-states the MDA/MCL lines to allow in-circuit
programming of the EEPROM.
0x4C—Bits[7:0] CSC C4 LSBs
0x59—Bit[6] MDA/MCL PU Disable
This bit resets the audio FIFO if underflow is detected.
0x59—Bit[0] MDA/MCL Three-State
This bit disables the inter MDA/MCL pull-ups.
Rev. 0 | Page 38 of 48
AD9396
2-WIRE SERIAL CONTROL PORT
A 2-wire serial interface control is provided in the AD9396.
Up to two AD9396 devices can be connected to the 2-wire serial
interface, with a unique address for each device.
Data Transfer via Serial Interface
The 2-wire serial interface comprises a clock (SCL) and a
bidirectional data (SDA) pin. The analog flat panel interface
acts as a slave for receiving and transmitting data over the serial
interface. When the serial interface is not active, the logic levels
on SCL and SDA are pulled high by external pull-up resistors.
If the AD9396 does not acknowledge the master device during a
write sequence, the SDA remains high so the master can generate a stop signal. If the master device does not acknowledge the
AD9396 during a read sequence, the AD9396 interprets this as
end of data. The SDA remains high, so the master can generate
a stop signal.
Data received or transmitted on the SDA line must be stable for
the duration of the positive-going SCL pulse. Data on SDA must
change only when SCL is low. If SDA changes state while SCL is
high, the serial interface interprets that action as a start or stop
sequence.
There are six components to serial bus operation:
•
Start signal
•
Slave address byte
•
Base register address byte
•
Data byte to read or write
•
Stop signal
•
Acknowledge (Ack)
The first eight bits of data transferred after a start signal
comprise a 7 bit slave address (the first 7 bits) and a single R/W
bit (the 8th bit). The R/W bit indicates the direction of data
transfer, read from (1) or write to (0) the slave device. If the
transmitted slave address matches the address of the device
(set by the state of the SA0 input pin, as shown in Table 21), the
AD9396 acknowledges by bringing SDA low on the 9th SCL
pulse. If the addresses do not match, the AD9396 does not
acknowledge.
Table 21. Serial Port Addresses
Bit 6
A5
0
Bit 5
A4
0
Writing data to specific control registers of the AD9396 requires
that the 8-bit address of the control register of interest be written after the slave address has been established. This control
register address is the base address for subsequent write operations. The base address auto-increments by one for each byte of
data written after the data byte intended for the base address. If
more bytes are transferred than there are available addresses,
the address does not increment and remains at its maximum
value. Any base address higher than the maximum value does
not produce an acknowledge signal.
Data are read from the control registers of the AD9396 in a
similar manner. Reading requires two data transfer operations:
When the serial interface is inactive (SCL and SDA are high)
communications are initiated by sending a start signal. The start
signal is a high-to-low transition on SDA while SCL is high.
This signal alerts all slave devices that a data transfer sequence
is coming.
Bit 4
A3
1
Bit 3
A2
1
Bit 2
A1
0
Bit 1
A0
0
•
The base address must be written with the R/W bit of the
slave address byte low to set up a sequential read
operation.
•
Reading (the R/W bit of the slave address byte high) begins
at the previously established base address. The address of
the read register auto-increments after each byte is
transferred.
To terminate a read/write sequence to the AD9396, a stop signal
must be sent. A stop signal comprises a low-to-high transition
of SDA while SCL is high.
A repeated start signal occurs when the master device driving
the serial interface generates a start signal without first generating a stop signal to terminate the current communication. This
is used to change the mode of communication (read, write)
between the slave and master without releasing the serial
interface lines.
SDA
tBUFF
tSTAH
tDSU
tDHO
tSTASU
tSTOSU
tDAL
SCL
05690-016
Bit 7
A6 (MSB)
1
For each byte of data read or written, the MSB is the first bit of
the sequence.
tDAH
Figure 16. Serial Port Read/Write Timing
Rev. 0 | Page 39 of 48
AD9396
Serial Interface Read/Write Examples
Write to one control register:
Read from one control register:
•
Start signal
•
Start signal
•
Slave address byte (R/W bit = low)
•
Slave address byte (R/W bit = low)
•
Base address byte
•
Base address byte
•
Data byte to base address
•
Start signal
•
Stop signal
•
Slave address byte (R/W bit = high)
•
Data byte from base address
•
Stop signal
Write to four consecutive control registers:
•
Start signal
•
Slave address byte (R/W bit = low)
Read from four consecutive control registers:
•
Base address byte
•
Start signal
•
Data byte to base address
•
Slave address byte (R/W bit = low)
•
Data byte to (base address + 1)
•
Base address byte
•
Data byte to (base address + 2)
•
Start signal
•
Data byte to (base address + 3)
•
Slave address byte (R/W bit = high)
•
Stop signal
•
Data byte from base address
•
Data byte from (base address + 1)
•
Data byte from (base address + 2)
•
Data byte from (base address + 3)
•
Stop signal
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
ACK
05690-017
SDA
SCL
Figure 17. Serial Interface—Typical Byte Transfer
Rev. 0 | Page 40 of 48
AD9396
PCB LAYOUT RECOMMENDATIONS
The AD9396 is a high precision, high speed analog device. To
achieve the maximum performance from the part, it is important to have a well laid-out board. The following is a guide for
designing a board using the AD9396.
ANALOG INTERFACE INPUTS
Using the following layout techniques on the graphics inputs is
extremely important:
•
Minimize the trace length running into the graphics inputs
by placing the AD9396 as close as possible to the graphics
VGA connector. Long input trace lengths are undesirable,
because they pick up more noise from the board and other
external sources.
•
Place the 75 Ω termination resistors (see Figure 3) as close
to the AD9396 chip as possible. Any additional trace length
between the termination resistors and the input of the
AD9396 increases the magnitude of reflections, which
corrupts the graphics signal.
•
Use 75 Ω matched impedance traces. Trace impedances
other than 75 Ω also increase the chance of reflections.
The AD9396 has very high input bandwidth (300 MHz). While
this is desirable for acquiring a high resolution PC graphics
signal with fast edges, it means that it also captures any high
frequency noise present. Therefore, it is important to reduce the
amount of noise that is coupled to the inputs. Avoid running
any digital traces near the analog inputs.
Due to the high bandwidth of the AD9396, sometimes low-pass
filtering the analog inputs can help to reduce noise. For many
applications, filtering is unnecessary. Experiments have shown
that placing a series ferrite bead prior to the 75 Ω termination
resistor is helpful in filtering out excess noise. Specifically, the
part used was the Fair-Rite 2508051217Z0, but each application
may work best with a different bead value. Alternatively, placing
a 100 Ω to 120 Ω resistor between the 75 Ω termination resistor
and the input coupling capacitor can also be beneficial.
POWER SUPPLY BYPASSING
It is recommended to bypass each power supply pin with a
0.1 μF capacitor. The exception is when two or more supply
pins are adjacent to each other. For these groupings of
powers/grounds, it is only necessary to have one bypass
capacitor. The fundamental idea is to have a bypass capacitor
within about 0.5 cm of each power pin. Also, avoid placing the
capacitor on the opposite side of the PC board from the
AD9396, because that interposes resistive vias in the path.
The bypass capacitors should be physically located between the
power plane and the power pin. Current should flow from the
power plane to the capacitor to the power pin. Do not make the
power connection between the capacitor and the power pin.
Placing a via underneath the capacitor pads down to the power
plane is generally the best approach.
It is particularly important to maintain low noise and good
stability of PVDD (the clock generator supply). Abrupt changes
in PVDD can result in similarly abrupt changes in sampling clock
phase and frequency. This can be avoided by careful attention to
regulation, filtering, and bypassing. It is highly desirable to
provide separate regulated supplies for each of the analog
circuitry groups (VD and PVDD).
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during HSYNC and VSYNC periods). This can result in a
measurable change in the voltage supplied to the analog supply
regulator, which can in turn produce changes in the regulated
analog supply voltage. This can be mitigated by regulating the
analog supply, or at least PVDD, from a different, cleaner, power
source (for example, from a 12 V supply).
It is recommended to use a single ground plane for the entire
board. Experience has shown repeatedly that the noise performance is the same or better with a single ground plane. Using
multiple ground planes can be detrimental because each
separate ground plane is smaller and long ground loops can
result.
When using separate ground planes is unavoidable, placing a
single ground plane under the AD9396 is recommended. The
location of the split should be at the receiver of the digital
outputs. In this case it is even more important to place components wisely because the current loops are much longer,
(current takes the path of least resistance). An example of a
current loop is: power plane to AD9396 to digital output
trace to digital data receiver to digital ground plane to analog
ground plane .
PLL
Place the PLL loop filter components as close as possible to the
FILT pin.
Do not place any digital or other high frequency traces near
these components.
Use the values suggested in the data sheet with 10% tolerances
or less.
Rev. 0 | Page 41 of 48
AD9396
OUTPUTS (BOTH DATA AND CLOCKS)
DIGITAL INPUTS
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, which require
more current that causes more internal digital noise.
The digital inputs on the AD9396 were designed to work with
3.3 V signals, but are tolerant of 5.0 V signals. Therefore, no
extra components need to be added if using 5.0 V logic.
Shorter traces reduce the possibility of reflections.
Any noise that enters the HSYNC input trace can add jitter to
the system. Therefore, minimize the trace length and do not run
any digital or other high frequency traces near it.
Adding a series resistor of value 50 Ω to 200 Ω can suppress
reflections, reduce EMI, and reduce the current spikes inside of
the AD9396. If series resistors are used, place them as close as
possible to the AD9396 pins (although try not to add vias or
extra length to the output trace to move the resistors closer).
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can be easily accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance increases
the current transients inside of the AD9396 and creates more
digital noise on its power supplies.
Rev. 0 | Page 42 of 48
AD9396
COLOR SPACE CONVERTER (CSC) COMMON SETTINGS
Table 22. HDTV YCrCb (0 to 255) to RGB (0 to 255) (Default Setting for AD9396)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x2C
0x3D
0x1C
0x45
0x00
Red/Cr Coeff 1
0x36
0x52
Green/Y Coeff 1
0x3E
0x54
Blue/Cb Coeff 1
0x46
0x00
0x37
0x08
0x3F
0x08
0x47
0x08
Red/Cr Coeff 2
0x38
0x00
Green/Y Coeff 2
0x40
0x00
Blue/Cb Coeff 2
0x48
0x00
0x39
0x00
0x41
0x3E
0x49
0x0E
Red/Cr Coeff 3
0x3A
0x00
Green/Y Coeff 3
0x42
0x89
Blue/Cb Coeff 3
0x4A
0x87
0x3B
0x19
0x43
0x02
0x4B
0x18
Red/Cr Offset
0x3C
0xD7
Green/Y Offset
0x44
0x91
Blue/Cb Offset
0x4C
0xBD
Table 23. HDTV YCrCb (16 to 235) to RGB (0 to 255)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x47
0x3D
0x1D
0x45
0x00
Red/Cr Coeff 1
0x36
0x2C
Green/Y Coeff 1
0x3E
0xDD
Blue/Cb Coeff 1
0x46
0x00
0x37
0x04
0x3F
0x04
0x47
0x04
Red/Cr Coeff 2
0x38
0xA8
Green/Y Coeff 2
0x40
0xA8
Blue/Cb Coeff 2
0x48
0xA8
0x39
0x00
0x41
0x1F
0x49
0x08
Red/Cr Coeff 3
0x3A
0x00
Green/Y Coeff 3
0x42
0x26
Blue/Cb Coeff 3
0x4A
0x 75
0x3B
0x1C
0x43
0x01
0x4B
0x1B
Red/Cr Offset
0x3C
0x1F
Green/Y Offset
0x44
0x34
Blue/Cb Offset
0x4C
0x7B
Table 24. SDTV YCrCb (0 to 255) to RGB (0 to 255)
Register
Address
Value
Register
Address
Value
Register
Address
Value
Red/Cr Coeff 1
0x36
0xF8
Green/Y Coeff 1
0x3D
0x3E
0x1A
0x6A
Blue/Cb Coeff. 1
0x45
0x46
0x00
0x00
0x35
0x2A
0x37
0x08
0x3F
0x08
0x47
0x08
Red/Cr Coeff 2
0x38
0x00
Green/Y Coeff 2
0x40
0x00
Blue/Cb Coeff 2
0x48
0x00
0x39
0x00
0x41
0x1D
0x49
0x0D
Red/Cr Coeff 3
0x3A
0x00
Green/Y Coeff 3
0x42
0x50
Blue/Cb Coeff 3
0x4A
0xDB
0x3B
0x1A
0x43
0x04
0x4B
0x19
Red/Cr Offset
0x3C
0x84
Green/Y Offset
0x44
0x23
Blue/Cb Offset
0x4C
0x12
Table 25. SDTV YCrCb (16 to 235) to RGB (0 to 255)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x46
0x3D
0x1C
0x45
0x00
Red/Cr Coeff 1
0x36
0x63
Green/Y Coeff 1
0x3E
0xC0
Blue/Cb Coeff 1
0x46
0x00
0x37
0x04
0x3F
0x04
0x47
0x04
Red/Cr Coeff 2
0x38
0xA8
Green/Y Coeff 2
0x40
0xA8
Blue/Cb Coeff 2
0x48
0xA8
Rev. 0 | Page 43 of 48
0x39
0x00
0x41
0x1E
0x49
0x08
Red/Cr Coeff 3
0x3A
0x00
Green/Y Coeff 3
0x42
0x6F
Blue/Cb Coeff 3
0x4A
0x11
0x3B
0x1C
0x43
0x02
0x4B
0x1B
Red/Cr Offset
0x3C
0x84
Green/Y Offset
0x44
0x1E
Blue/Cb Offset
0x4C
0xAD
AD9396
Table 26. RGB (0 to 255) to HDTV YCrCb (0 to 255)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x28
0x3D
0x03
0x45
0x1E
Red/Cr Coeff 1
0x36
0x2D
Green/Y Coeff 1
0x3E
0x68
Blue/Cb Coeff 1
0x46
0x21
0x37
0x18
0x3F
0x0B
0x47
0x19
Red/Cr Coeff 2
0x38
0x93
Green/Y Coeff 2
0x40
0x71
Blue/Cb Coeff 2
0x48
0xB2
0x39
0x1F
0x41
0x01
0x49
0x08
Red/Cr Coeff 3
0x3A
0x3F
Green/Y Coeff 3
0x42
0x27
Blue/Cb Coeff 3
0x4A
0x2D
0x3B
0x08
0x43
0x00
0x4B
0x08
Red/Cr Offset
0x3C
0x00
Green/Y Offset
0x44
0x00
Blue/Cb Offset
0x4C
0x00
Table 27. RGB (0 to 255) to HDTV YCrCb (16 to 235)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x27
0x3D
0x02
0x45
0x1E
Red/Cr Coeff 1
0x36
0x06
Green/Y Coeff 1
0x3E
0xED
Blue/Cb Coeff 1
0x46
0x64
0x37
0x19
0x3F
0x09
0x47
0x1A
Red/Cr Coeff 2
0x38
0xA0
Green/Y Coeff 2
0x40
0xD3
Blue/Cb Coeff 2
0x48
0x96
0x39
0x1F
0x41
0x00
0x49
0x07
Red/Cr Coeff 3
0x3A
0x5B
Green/Y Coeff 3
0x42
0xFD
Blue/Cb Coeff 3
0x4A
0x06
0x3B
0x08
0x43
0x01
0x4B
0x08
Red/Cr Offset
0x3C
0x00
Green/Y Offset
0x44
0x00
Blue/Cb Offset
0x4C
0x00
Table 28. RGB (0 to 255) to SDTV YCrCb (0 to 255)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x28
0x3D
0x04
0x45
0x1D
Red/Cr Coeff 1
0x36
0x2D
Green/Y Coeff 1
0x3E
0xC9
Blue/Cb Coeff 1
0x46
0x3F
0x37
0x19
0x3F
0x09
0x47
0x1A
Red/Cr Coeff 2
0x38
0x27
Green/Y Coeff 2
0x40
0x64
Blue/Cb Coeff 2
0x48
0x93
0x39
0x1E
0x41
0x01
0x49
0x08
Red/Cr Coeff 3
0x3A
0xAC
Green/Y Coeff 3
0x42
0xD3
Blue/Cb Coeff 3
0x4A
0x2D
0x3B
0x08
0x43
0x00
0x4B
0x08
Red/Cr Offset
0x3C
0x00
Green/Y Offset
0x44
0x00
Blue/Cb Offset
0x4C
0x00
Table 29. RGB (0 to 255) to SDTV YCrCb (16 to 235)
Register
Address
Value
Register
Address
Value
Register
Address
Value
0x35
0x27
0x3D
0x04
0x45
0x1D
Red/Cr Coeff 1
0x36
0x06
Green/Y Coeff 1
0x3E
0x1C
Blue/Cb Coeff 1
0x46
0xA3
0x37
0x1A
0x3F
0x08
0x47
0x1B
Red/Cr Coeff 2
0x38
0x1E
Green/Y Coeff 2
0x40
0x11
Blue/Cb Coeff 2
0x48
0x57
Rev. 0 | Page 44 of 48
0x39
0x1E
0x41
0x01
0x49
0x07
Red/Cr Coeff 3
0x3A
0xDC
Green/Y Coeff 3
0x42
0x91
Blue/Cb Coeff 3
0x4A
0x06
0x3B
0x08
0x43
0x01
0x4B
0x08
Red/Cr Offset
0x3C
0x00
Green/Y Offset
0x44
0x00
Blue/Cb Offset
0x4C
0x00
AD9396
OUTLINE DIMENSIONS
16.00
BSC SQ
1.60 MAX
0.75
0.60
0.45
100
1
76
75
PIN 1
14.00
BSC SQ
TOP VIEW
(PINS DOWN)
1.45
1.40
1.35
0.15
0.05
SEATING
PLANE
0.20
0.09
7°
3.5°
0°
0.08 MAX
COPLANARITY
25
51
50
26
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
ROTATED 90° CCW
0.27
0.22
0.17
COMPLIANT TO JEDEC STANDARDS MS-026-BED
Figure 18. 100-Lead Low Profile Quad Flat Package [LQFP]
(ST-100)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9396KSTZ-100 1
AD9396KSTZ-1501
AD9396/PCB
1
Max Speeds (MHz)
Analog
Digital
100
100
150
150
Temperature
Range
0°C to 70°C
0°C to 70°C
Package Description
100-Lead Low Profile Quad Flat Package (LQFP)
100-Lead Low Profile Quad Flat Package (LQFP)
Evaluation Board
Z = Pb-free part.
Rev. 0 | Page 45 of 48
Package
Option
ST-100
ST-100
AD9396
NOTES
Rev. 0 | Page 46 of 48
AD9396
NOTES
Rev. 0 | Page 47 of 48
AD9396
NOTES
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05690-0-10/05(0)
Rev. 0 | Page 48 of 48