DVI Display Interface AD9397 FUNCTIONAL BLOCK DIAGRAM FEATURES SCL SDA SERIAL REGISTER AND POWER MANAGEMENT R/G/B 8 × 3 DIGITAL INTERFACE R/G/B 8 × 3 OR YCbCr Rx0+ Rx0– 2 Rx1+ HSYNC Rx1– Rx2+ DATACK DE DVI RECEIVER RGB ↔YCbCr MATRIX DVI interface Supports high-bandwidth digital content protection RGB to YCbCr 2-way color conversion 1.8 V/3.3 V power supply 100-lead, Pb-free LQFP RGB and YCbCr output formats Digital video interface DVI 1.0 150 MHz DVI receiver Supports high-bandwidth digital content protection (HDCP 1.1) 2 DATACK HSOUT VSOUT SOGOUT VSYNC Rx2– APPLICATIONS YCbCr (4:2:2 OR 4:4:4) DE RxC+ RxC– RTERM DDCSCL DDCSDA MCL HDCP MDA AD9397 05691-001 Advanced TVs HDTVs Projectors LCD monitors Figure 1. GENERAL DESCRIPTION The AD9397 is a digital visual interface (DVI) receiver integrated on a single chip. Also included is support for high bandwidth digital content protection (HDCP) with internal key storage. video content. The AD9397 allows for authentication of a video receiver, decryption of encoded data at the receiver, and renewability of that authentication during transmission as specified by the HDCP 1.1 protocol. The AD9397 contains a DVI 1.0-compatible receiver and supports all HDTV formats (up to 1080p and 720p) and display resolutions up to SXGA (1280 × 1024 @ 80 Hz). The receiver features an intrapair skew tolerance of up to one full clock cycle. With the inclusion of HDCP, displays can receive encrypted Fabricated in an advanced CMOS process, the AD9397 is provided in a space-saving, 100-lead, surface-mount, Pb-free plastic LQFP and is specified over the 0°C to 70°C temperature range. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 © 2005 Analog Devices, Inc. All rights reserved. AD9397 TABLE OF CONTENTS Features .............................................................................................. 1 DVI Receiver............................................................................... 11 Applications....................................................................................... 1 DE Generator.............................................................................. 11 Functional Block Diagram .............................................................. 1 4:4:4 to 4:2:2 Filter ...................................................................... 12 General Description ......................................................................... 1 Output Data Formats................................................................. 12 Revision History ............................................................................... 2 2-Wire Serial Register Map ........................................................... 13 Specifications..................................................................................... 3 2-Wire Serial Control Register Details ........................................ 18 Electrical Characteristics............................................................. 3 Chip Identification ..................................................................... 18 Digital Interface Electrical Characteristics ............................... 4 BT656 Generation ...................................................................... 20 Absolute Maximum Ratings............................................................ 6 Macrovision................................................................................. 21 Explanation of Test Levels ........................................................... 6 Color Space Conversion ............................................................ 21 ESD Caution.................................................................................. 6 2-Wire Serial Control Port ............................................................ 23 Pin Configuration and Function Descriptions............................. 7 Data Transfer via Serial Interface............................................. 23 Design Guide................................................................................... 10 Serial Interface Read/Write Examples ..................................... 24 General Description................................................................... 10 PCB Layout Recommendations.................................................... 25 Digital Inputs .............................................................................. 10 Power Supply Bypassing ............................................................ 25 Serial Control Port ..................................................................... 10 Outputs (Both Data and Clocks).............................................. 25 Output Signal Handling............................................................. 10 Digital Inputs .............................................................................. 25 Power Management.................................................................... 10 Color Space Converter (CSC) Common Settings...................... 26 Timing.............................................................................................. 11 Outline Dimensions ....................................................................... 28 HSYNC Timing .......................................................................... 11 Ordering Guide .......................................................................... 28 VSYNC Filter and Odd/Even Fields ........................................ 11 REVISION HISTORY 10/05—Revision 0: Initial Version Rev. 0 | Page 2 of 28 AD9397 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VDD, VD = 3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum. Table 1. Parameter RESOLUTION Data-to-Clock Skew Serial Port Timing tBUFF tSTAH tDHO tDAL tDAH tDSU tSTASU tSTOSU DIGITAL INPUTS (5 V TOLERANT) Input Voltage, High (VIH) Input Voltage, Low (VIL) Input Current, High (IIH) Input Current, Low (IIL) Input Capacitance DIGITAL OUTPUTS Output Voltage, High (VOH) Output Voltage, Low (VOL) Duty Cycle, DATACK Output Coding POWER SUPPLY VD Supply Voltage DVDD Supply Voltage VDD Supply Voltage PVDD Supply Voltage ID Supply Current (VD) IDVDD Supply Current (DVDD) IDD Supply Current (VDD) 1 IPVDD Supply Current (PVDD) Total Power Power-Down Dissipation THERMAL CHARACTERISTICS θJA Junction to Ambient Min Min IV AD9397KSTZ-100 Typ Max 8 −0.5 +2.0 AD9397KSTZ-150 Typ Max 8 −0.5 +2.0 Unit Bits ns Full Full Full Full Full Full Full Full VI VI VI VI VI VI VI VI 4.7 4.0 0 4.7 4.0 250 4.7 4.0 4.7 4.0 0 4.7 4.0 250 4.7 4.0 μs μs μs μs μs ns μs μs Full Full Full Full 25°C VI VI V V V 2.6 Full Full Full VI VI V VDD − 0.1 45 50 Binary Full Full Full Full 25°C 25°C 25°C 25°C Full Full IV IV IV IV VI VI VI VI VI VI 3.15 1.7 1.7 1.7 3.3 1.8 3.3 1.8 260 45 37 10 1.1 130 Temp Test Level Full 2.6 0.8 0.8 −82 82 3 V VDD − 0.1 35 1 DATACK load = 15 pF, data load = 5 pF. 2 Specified current and power values with a worst-case pattern (on/off). Rev. 0 | Page 3 of 28 −82 82 3 0.4 55 3.47 1.9 3.47 1.9 300 60 100 2 15 1.4 45 50 Binary 3.15 1.7 1.7 1.7 3.3 1.8 3.3 1.8 1.15 130 35 0.4 55 3.47 1.9 3.47 1.9 330 85 1302 20 1.4 V V μA μA pF V V % V V V V mA mA mA mA W mW °C/W AD9397 DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS VDD = VD = 3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum. Table 2. Parameter RESOLUTION DC DIGITAL I/O SPECIFICATIONS High Level Input Voltage, (VIH) Low Level Input Voltage, (VIL) High Level Output Voltage, (VOH) Low Level Output Voltage, (VOL) DC SPECIFICATIONS Output High Level IOHD, (VOUT = VOH) Output Low Level IOLD, (VOUT = VOL) DATACK High Level VOHC, (VOUT = VOH) DATACK Low Level VOLC, (VOUT = VOL) Differential Input Voltage, Single-Ended Amplitude POWER SUPPLY VD Supply Voltage VDD Supply Voltage DVDD Supply Voltage PVDD Supply Voltage IVD Supply Current (Typical Pattern) 1 IVDD Supply Current (Typical Pattern) 2 IDVDD Supply Current (Typical Pattern)1, 4 IPVDD Supply Current (Typical Pattern)1 Power-Down Supply Current (IPD) Test Level Conditions VI VI VI VI IV IV IV IV IV IV IV IV IV AD9397KSTZ-100 Min Typ Max 8 AD9397KSTZ-150 Min Typ Max 8 2.5 2.5 VDD − 0.1 VDD − 0.1 Output drive = high Output drive = low Output drive = high Output drive = low Output drive = high Output drive = low Output drive = high Output drive = low IV IV IV IV V V V V VI 3.15 1.7 1.7 1.7 Rev. 0 | Page 4 of 28 0.8 0.8 0.1 0.1 V V V V 700 mA mA mA mA mA mA mA mA mV 36 24 12 8 40 20 30 15 75 3.3 3.3 1.8 1.8 80 40 88 26 130 Unit Bit 36 24 12 8 40 20 30 15 700 75 3.47 347 1.9 1.9 100 100 3 110 35 3.15 1.7 1.7 1.7 3.3 3.3 1.8 1.8 80 55 110 30 130 3.47 347 1.9 1.9 110 1753 145 40 V V V V mA mA mA mA mA AD9397 Parameter AC SPECIFICATIONS Intrapair (+ to −) Differential Input Skew (TDPS) Channel to Channel Differential Input Skew (TCCS) Low-to-High Transition Time for Data and Controls (DLHT) Test Level IV 6 900 Clock Period ps 1300 ps 650 ps 1200 ps 850 ps 1250 ps 800 ps 1200 ps +2.0 55 150 ns % MHz IV IV IV IV IV Clock to Data Skew 5 (TSKEW) Duty Cycle, DATACK5 DATACK Frequency (FCIP) Unit ps IV High-to-Low Transition Time for DATACK (DHLT) AD9397KSTZ-150 Min Typ Max 360 IV High-to-Low Transition Time for Data and Controls (DHLT) AD9397KSTZ-100 Min Typ Max IV IV Low-to-High Transition Time for DATACK (DLHT) Conditions Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF IV IV VI −0.5 45 20 1 +2.0 50 The typical pattern contains a gray scale area, output drive = high. Worst-case pattern is alternating black and white pixels. The typical pattern contains a gray scale area, output drive = high. Specified current and power values with a worst-case pattern (on/off). 4 DATACK load = 10 pF, data load = 5 pF. 5 Drive strength = high. 2 3 Rev. 0 | Page 5 of 28 −0.5 AD9397 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VD VDD DVDD PVDD Analog Inputs Digital Inputs Digital Output Current Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Maximum Case Temperature Rating 3.6 V 3.6 V 1.98 V 1.98 V VD to 0.0 V 5 V to 0.0 V 20 mA −25°C to + 85°C −65°C to + 150°C 150°C 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. EXPLANATION OF TEST LEVELS Table 4. Level I II III IV V VI Test 100% production tested. 100% production tested at 25°C and sample tested at specified temperatures. Sample tested only. Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. 100% production tested at 25°C; guaranteed by design and characterization testing. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 6 of 28 AD9397 VDD RED 0 RED 1 RED 2 RED 3 RED 4 RED 5 RED 6 RED 7 GND VDD DATACK DE HSOUT NC VSOUT FIELD SDA SCL PWRDN VD NC GND NC VD 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS GND 74 NC 3 73 NC GREEN 5 4 72 VD GREEN 4 5 71 NC GREEN 3 6 70 NC GREEN 2 7 69 GND GREEN 1 8 68 NC GREEN 0 9 67 VD VDD 10 AD9397 66 NC GND 11 65 GND BLUE 7 12 TOP VIEW (Not to Scale) 64 NC BLUE 6 13 63 NC BLUE 5 14 62 NC BLUE 4 15 61 NC BLUE 3 16 60 NC BLUE 2 17 59 PVDD BLUE 1 18 58 GND BLUE 0 19 57 NC NC 20 56 PVDD NC 21 55 GND NC 22 54 PVDD NC 23 53 GND CTL3 24 52 MDA CTL2 25 51 MCL 39 40 41 42 43 44 45 46 47 48 49 50 GND Rx2– Rx2+ GND RxC+ RxC– VD RTERM GND DVDD DDCSCL DDCSDA 37 Rx1– 38 36 GND Rx1+ 35 32 DVDD Rx0+ 31 GND 34 30 DVDD Rx0– 29 GND 33 28 NC VD 27 NC = NO CONNECT 26 GREEN 6 PIN 1 CTL0 2 CTL1 1 05691-002 75 GND GREEN 7 Figure 2. Pin Configuration Table 5. Complete Pinout List Pin Type INPUTS DIGITAL VIDEO DATA INPUTS DIGITAL VIDEO CLOCK INPUTS OUTPUTS Pin No. 81 35 34 38 37 41 40 43 44 92 to 99 2 to 9 12 to 19 89 87 85 84 27, 26, 25, 24 Mnemonic PWRDN Rx0+ Rx0− Rx1+ Rx1− Rx2+ Rx2− RxC+ RxC− RED [7:0] GREEN [7:0] BLUE [7:0] DATACK HSOUT VSOUT O/E FIELD CTL(0 to 3) Function Power-Down Control Digital Input Channel 0 True Digital Input Channel 0 Complement Digital Input Channel 1 True Digital Input Channel 1 Complement Digital Input Channel 2 True Digital Input Channel 2 Complement Digital Data Clock True Digital Data Clock Complement Outputs of Red Converter, Bit 7 is MSB Outputs of Green Converter, Bit 7 is MSB Outputs of Blue Converter, Bit 7 is MSB Data Output Clock HSYNC Output Clock (Phase-Aligned with DATACK) VSYNC Output Clock (Phase-Aligned with DATACK) Odd/Even Field Output Control 0, 1, 2, 3 Rev. 0 | Page 7 of 28 Value 3.3 V CMOS TMDS TMDS TMDS TMDS TMDS TMDS TMDS TMDS VDD VDD VDD VDD VDD VDD VDD VDD AD9397 Pin Type POWER SUPPLY CONTROL HDCP DATA ENABLE RTERM Pin No. 80, 76, 72, 67, 45, 33 100, 90, 10 59, 56, 54 48, 32, 30 83 82 49 50 51 52 88 46 Mnemonic VD Function Analog Power Supply and DVI Terminators Value 3.3 V VDD PVDD DVDD GND SDA SCL DDCSCL DDCSDA MCL MDA DE RTERM Output Power Supply PLL Power Supply Digital Logic Power Supply Ground Serial Port Data I/O Serial Port Data Clock HDCP Slave Serial Port Data Clock HDCP Slave Serial Port Data I/O HDCP Master Serial Port Data Clock HDCP Master Serial Port Data I/O Data Enable Sets Internal Termination Resistance 1.8 V to 3.3 V 1.8 V 1.8 V 0V 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 500 Ω Table 6. Pin Function Descriptions Pin INPUTS Rx0+ Rx0− Rx1+ Rx1− Rx2+ Rx2− RxC+ RxC− PWRDN RTERM OUTPUTS HSOUT VSOUT FIELD DE CTL(3-0) SERIAL PORT SDA SCL DDCSDA DDCSCL MDA MCL Description Digital Input Channel 0 True. Digital Input Channel 0 Complement. Digital Input Channel 1 True. Digital Input Channel 1 Complement. Digital Input Channel 2 True. Digital input Channel 2 Complement. These six pins receive three pairs of transition minimized differential signaling (TMDS ) pixel data (at 10× the pixel rate) from a digital graphics transmitter. Digital Data Clock True. Digital Data Clock Complement. This clock pair receives a TMDS clock at 1× pixel data rate. Power-Down Control/Three-State Control. The function of this pin is programmable via Register 0x26 [2:1]. RTERM is the termination resistor used to drive the AD9397 internally to a precise 50 Ω termination for TMDS lines. This should be a 500 Ω 1% tolerance resistor. Horizontal Sync Output. A reconstructed and phase-aligned version of the HSYNC input. Both the polarity and duration of this output can be programmed via serial bus registers. By maintaining alignment with DATACK and Data, data timing with respect to horizontal sync can always be determined. Vertical Sync Output. The separated VSYNC from a composite signal or a direct pass through of the VSYNC signal. The polarity of this output can be controlled via the serial bus bit (Register 0x24 [6]). Odd/Even Field Bit for Interlaced Video. This output identifies whether the current field (in an interlaced signal) is odd or even. The polarity of this signal is programmable via Register 0x24[4]. Data Enable that defines valid video. Can be received in the signal or generated by the AD9397. Control 3, Control 2, Control 1, and Control 0 are output from the DVI stream. Refer to the DVI 1.0 specification for explanation. Serial Port Data I/O for Programming AD9397 Registers—I2C Address is 0x98. Serial Port Data Clock for Programming AD9397 Registers. Serial Port Data I/O for HDCP Communications to Transmitter—I2C Address is 0x74 or 0x76. Serial Port Data Clock for HDCP Communications to Transmitter. Serial Port Data I/O to EEPROM with HDCP Keys—I2C Address is 0xA0. Serial Port Data Clock to EEPROM with HDCP Keys. Rev. 0 | Page 8 of 28 AD9397 Pin DATA OUTPUTS RED [7:0] GREEN [7:0] BLUE [7:0] DATA CLOCK OUTPUT DATACK POWER SUPPLY 1 VD (3.3 V) VDD (1.8 V to 3.3 V) PVDD (1.8 V) DVDD (1.8 V) GND 1 Description Data Output, Red Channel. Data Output, Green Channel. Data Output, Blue Channel. The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output is fixed, but is different if the color space converter is used. When the sampling time is changed by adjusting the phase register, the output timing is shifted as well. The DATACK and HSOUT outputs are also moved, so the timing relationship among the signals is maintained. Data Clock Output. This is the main clock output signal used to strobe the output data and HSOUT into external logic. Four possible output clocks can be selected with Register 0x25 [7:6]. These are related to the pixel clock (1/2× pixel clock, 1× pixel clock, 2× frequency pixel clock, and a 90° phase shifted pixel clock). They are produced either by the internal PLL clock generator or EXTCLK and are synchronous with the pixel sampling clock. The polarity of DATACK can also be inverted via Register 0x24 [0]. The sampling time of the internal pixel clock can be changed by adjusting the phase register. When this is changed, the pixelrelated DATACK timing is shifted as well. The DATA, DATACK, and HSOUT outputs are all moved, so the timing relationship among the signals is maintained. Analog Power Supply. These pins supply power to the ADCs and terminators. They should be as quiet and filtered as possible. Digital Output Power Supply. A large number of output pins (up to 27) switching at high speed (up to 150 MHz) generates many power supply transients (noise). These supply pins are identified separately from the VD pins, so output noise transferred into the sensitive analog circuitry can be minimized. If the AD9397 is interfacing with lower voltage logic, VDD may be connected to a lower supply voltage (as low as 1.8 V) for compatibility. Clock Generator Power Supply. The most sensitive portion of the AD9397 is the clock generation circuitry. These pins provide power to the clock PLL and help the user design for optimal performance. The designer should provide quiet, noise-free power to these pins. Digital Input Power Supply. This supplies power to the digital logic. Ground. The ground return for all circuitry on chip. It is recommended that the AD9397 be assembled on a single solid ground plane, with careful attention to ground current paths. The supplies should be sequenced such that VD and VDD are never less than 300 mV below DVDD. At no time should DVDD be more than 300 mV greater than VD or VDD. Rev. 0 | Page 9 of 28 AD9397 DESIGN GUIDE GENERAL DESCRIPTION SERIAL CONTROL PORT The AD9397 is a fully integrated digital visual interface (DVI ) for receiving RGB or YUV signals for display on flat panel monitors, projectors or PDPs. This interface is capable of decoding HDCP-encrypted signals through connection to an external EEPROM. The circuit is ideal for providing an interface for HDTV monitors or as the front-end to high performance video scan converters. The serial control port is designed for 3.3 V logic. However, it is tolerant of 5 V logic signals. Implemented in a high performance CMOS process, the interface can capture signals with pixel rates of up to 150 MHz. The AD9397 includes all necessary input buffering, signal dc restoration (clamping), offset and gain (brightness and contrast) adjustment, pixel clock generation, sampling phase control, and output data formatting. Included in the output formatting is a color space converter (CSC), which accommodates any input color space and can output any color space. All controls are programmable via a 2-wire serial interface. Full integration of these sensitive analog functions makes system design straightforward and less sensitive to the physical and electrical environments. DIGITAL INPUTS All digital control inputs (HSYNC, VSYNC, I2C) on the AD9397 operate to 3.3 V CMOS levels. In addition, all digital inputs except the TMDS (DVI) inputs are 5 V tolerant. (Applying 5 V to them does not cause any damage.) TMDS inputs (Rx0+/Rx0–, Rx1+/Rx1–, Rx2+/Rx2–, and RxC+/RxC–) must maintain a 100 Ω differential impedance (through proper PCB layout) from the connector to the input where they are internally terminated (50 Ω to 3.3 V). If additional ESD protection is desired, use of a California Micro Devices (CMD) CM1213 (among others) series low capacitance ESD protection offers 8 kV of protection to the HDMI TMDS lines. OUTPUT SIGNAL HANDLING The digital outputs operate from 1.8 V to 3.3 V (VDD). POWER MANAGEMENT The AD9397 uses the activity detect circuits, the active interface bits in the serial bus, the active interface override bits, the power-down bit, and the power-down pin to determine the correct power state. There are four power states: full-power, seek mode, auto power-down, and power-down. Table 7 summarizes how the AD9397 determines which power mode to be in and which circuitry is powered on/off in each of these modes. The power-down command has priority and then the automatic circuitry. The power-down pin (Pin 81—polarity set by Register 0x26[3]) can drive the chip into four power-down options. Bit 2 and Bit 1 of Register 0x26 control these four options. Bit 0 controls whether the chip is powered down or the outputs are placed in high impedance mode (with the exception of SOG). Bit 7 to Bit 4 of Register 0x26 control whether the outputs, SOG, Sony Philips digital interface (S/PDIF), or InterIC sound bus (I2S or IIS) outputs are in high impedance mode or not. See the 2-Wire Serial Control Register Detail section for more details. Table 7. Power-Down Mode Descriptions Mode Full Power Seek Mode Seek Mode Power-Down 1 2 3 Power-Down 1 1 1 1 0 Inputs Sync Detect 2 1 0 0 X Auto PD Enable 3 X 0 1 Power-On or Comments Everything Everything Serial bus, sync activity detect, SOG, band gap reference Serial bus, sync activity detect, SOG, band gap reference Power-down is controlled via Bit 0 in Serial Bus Register 0x26. Sync detect is determined by OR’ing Bit 7 to Bit 2 in Serial Bus Register 0x15. Auto power-down is controlled via Bit 7 in Serial Bus Register 0x27. Rev. 0 | Page 10 of 28 AD9397 TIMING SYNC SEPARATOR THRESHOLD The output data clock signal is created so that its rising edge always occurs between data transitions and can be used to latch the output data externally. FIELD 1 QUADRANT Figure 3 shows the timing operation of the AD9397. 2 3 FIELD 0 4 1 FIELD 1 2 3 FIELD 0 4 1 HSIN tPER VSIN tDCYCLE DATACK 05691-004 VSOUT O/E FIELD EVEN FIELD Figure 4. VSYNC Filter tSKEW 05691-003 DATA HSOUT SYNC SEPARATOR THRESHOLD Figure 3. Output Timing FIELD 1 HSYNC TIMING QUADRANT 2 3 FIELD 0 4 1 FIELD 1 2 3 FIELD 0 4 1 HSIN Horizontal sync (HSYNC) is processed in the AD9397 to eliminate ambiguity in the timing of the leading edge with respect to the phase-delayed pixel clock and data. VSIN The HSYNC input is used as a reference to generate the pixel sampling clock. The sampling phase can be adjusted, with respect to HSYNC, through a full 360° in 32 steps via the phase adjust register (to optimize the pixel sampling time). Display systems use HSYNC to align memory and display write cycles, so it is important to have a stable timing relationship between the HSYNC output (HSOUT) and data clock (DATACK). VSYNC FILTER AND ODD/EVEN FIELDS The VSYNC filter is used to eliminate spurious VSYNCs, maintain a consistent timing relationship between the VSYNC and HSYNC output signals, and generate the odd/even field output. The filter works by examining the placement of VSYNC with respect to HSYNC and, if necessary, slightly shifting it in time at the VSOUT output. The goal is to keep the VSYNC and HSYNC leading edges from switching at the same time, eliminating confusion as to when the first line of a frame occurs. Enabling the VSYNC filter is done with Register 0x21[5]. Use of the VSYNC filter is recommended for all cases, including interlaced video, and is required when using the HSYNC per VSYNC counter. Figure 4 and Figure 5 illustrate even/odd field determination in two situations. O/E FIELD ODD FIELD 05691-005 VSOUT Figure 5. VSYNC Filter—Odd/Even DVI RECEIVER The DVI receiver section of the AD9397 allows the reception of a digital video stream compatible with DVI 1.0. Embedded in this data stream are HSYNCs, VSYNCs, and display enable (DE) signals. DVI restricts the received format to RGB, but the inclusion of a programmable color space converter (CSC) allows the output to be tailored to any format necessary. With this, the scaler following the AD9397 can specify that it always wishes to receive a particular format—for instance, 4:2:2 YCrCb—regardless of the transmitted mode. If RGB is sent, the CSC can easily convert that to 4:2:2 YCrCb while relieving the scaler of this task. DE GENERATOR The AD9397 has an onboard generator for DE, for start of active video (SAV), and for end of active video (EAV), all of which are necessary for describing the complete data stream for a BT656-compatible output. In addition to this particular output, it is possible to generate the DE for cases in which a scaler is not used. This signal alerts the following circuitry as to which are displayable video pixels. Rev. 0 | Page 11 of 28 AD9397 4:4:4 TO 4:2:2 FILTER The AD9397 contains a filter that allows it to convert a signal from YCrCb 4:4:4 to YCrCb 4:2:2 while maintaining the maximum accuracy and fidelity of the original signal. Input Color Space to Output Color Space The AD9397 can support a wide variety of output formats, such as: • RGB 24-bit • 4:4:4 YCrCb 8-bit • 4:2:2 YCrCb 8-bit, 10-bit, and 12-bit • Dual 4:2:2 YCrCb 8-bit One of the three channels is represented in Figure 6. In each processing channel, the three inputs are multiplied by three separate coefficients marked a1, a2, and a3. These coefficients are divided by 4096 to obtain nominal values ranging from –0.9998 to +0.9998. The variable labeled a4 is used as an offset control. The CSC_Mode setting is the same for all three processing channels. This multiplies all coefficients and offsets by a factor of 2CSC_Mode. The functional diagram for a single channel of the CSC, as shown in Figure 6, is repeated for the remaining G and B channels. The coefficients for these channels are b1, b2, b3, b4, c1, c2, c3, and c4. CSC_Mode[1:0] Color Space Conversion (CSC) Matrix The main inputs, RIN, GIN, and BIN, come from the 8-bit to 12-bit inputs from each channel. These inputs are based on the input format detailed in Table 9. The mapping of these inputs to the CSC inputs is shown in Table 8. Table 8. CSC Port Mapping CSC Input Channel RIN GIN BIN × RIN [11:0] × 1 4096 + + ×4 2 ×2 1 + ROUT [11:0] a2[12:0] 0 GIN [11:0] × × 1 4096 × 1 4096 a3[12:0] BIN [11:0] × 05691-006 The CSC matrix in the AD9397 consists of three identical processing channels. In each channel, three input values are multiplied by three separate coefficients. Also included are an offset value for each row of the matrix and a scaling multiple for all values. Each value has a 13-bit, twos complement resolution to ensure the signal integrity is maintained. The CSC is designed to run at speeds up to 150 MHz supporting resolutions up to 1080p at 60 Hz. With any-to-any color space support, formats such as RGB, YUV, YCbCr, and others are supported by the CSC. Input Channel R/CR Gr/Y B/CB a4[12:0] a1[12:0] Figure 6. Single CSC Channel A programming example and register settings for several common conversions are listed in the Color Space Converter (CSC) Common Settings section. For a detailed functional description and more programming examples, refer to the Application Note AN-795, AD9880 Color Space Converter User's Guide. OUTPUT DATA FORMATS The AD9398 supports 4:4:4, 4:2:2, double data-rate (DDR), and BT656 output formats. Register 0x25[3:0] controls the output mode. These modes and the pin mapping are illustrated in Table 8. B Table 9. Port Bit 4:4:4 4:2:2 4:4:4 DDR 4:2:2 to 12 1 Red 7 6 5 4 Red/Cr [7:0] CbCr [7:0] DDR ↑ 1 G [3:0] DDR ↓ R [7:0] CbCr[11:0] 3 2 1 DDR ↑ B [7:4] 0 Green 7 6 5 4 Green/Y [7:0] Y [7:0] DDR ↑ B [3:0] DDR ↓ G [7:4] Arrows in the table indicate clock edge. Rising edge of clock = ↑, falling edge = ↓. Rev. 0 | Page 12 of 28 Blue 7 6 5 4 3 Blue/Cb [7:0] DDR 4:2:2 ↑ CbCr ↓ Y, Y DDR 4:2:2 ↑ CbCr [11:0] DDR 4:2:2 ↓ Y,Y [11:0] Y [11:0] 3 2 1 0 2 1 0 AD9397 2-WIRE SERIAL REGISTER MAP The AD9397 is initialized and controlled by a set of registers that determines the operating modes. An external controller is employed to write and read the control registers through the 2-wire serial interface port. Table 10. Control Register Map Hex Address 0x00 0x11 0x12 Read/Write or Read Only Read Read/Write Read/Write Bits [7:0] [7] Default Value 00000000 0******* [6] *0****** HSYNC Source Override [5] **0***** VSYNC Source [4] ***0**** VSYNC Source Override [3] ****0*** Channel Select [2] *****0** Channel Select Override [1] ******0* Interface Select [0] *******0 Interface Override [7] 1******* Input HSYNC Polarity [6] *0****** HSYNC Polarity Override [5] **1***** Input VSYNC Polarity [4] ***0**** VSYNC Polarity Override HSYNCs per VSYNC MSB HSYNCs per VSYNC VSYNC Duration HSYNC Duration 0x17 Read [3:0] ****0000 0x18 0x22 0x23 Read Read/Write Read/Write [7:0] [7:0] [7:0] 00000000 4 32 0x24 Read/Write [7] 1******* [6] [5] *1****** **1***** Register Name Chip Revision HSYNC Source HSYNC Output Polarity VSYNC Output Polarity DE Output Polarity Description Chip revision ID. 0 = HSYNC. 1 = SOG. 0 = auto HSYNC source. 1 = manual HSYNC source. 0 = VSYNC. 1 = VSYNC from SOG. 0 = auto HSYNC source. 1 = manual HSYNC source. 0 = Channel 0. 1 = Channel 1. 0 = autochannel select. 1 = manual channel select. 0 = analog interface. 1 = digital interface. 0 = auto-interface select. 1 = manual interface select. 0 = active low. 1 = active high. 0 = auto HSYNC polarity. 1 = manual HSYNC polarity. 0 = active low. 1 = active high. 0 = auto VSYNC polarity. 1 = manual VSYNC polarity. MSB of HSYNCs per VSYNC. HSYNCs per VSYNC count. VSYNC duration. HSYNC duration. Sets the duration of the output HSYNC in pixel clocks. Output HSYNC polarity. 0 = active low out. 1 = active high out. Output VSYNC polarity. 0 = active low out. 1 = active high out. Output DE polarity. 0 = active low out. 1 = active high out. Rev. 0 | Page 13 of 28 AD9397 Hex Address 0x25 0x26 Read/Write or Read Only Read/Write Read/Write Bits [4] Default Value ***1**** Register Name Field Output Polarity [0] *******0 Output CLK Invert [7:6] 01****** Output CLK Select [5:4] **11**** Output Drive Strength [3:2] ****00** Output Mode [1] ******1* [0] *******0 [7] [5] [4] [3] 0******* **0***** ***0**** ****1*** Primary Output Enable Secondary Output Enable Output Three-State SPDIF Three-State I2S Three-State Power-Down Pin Polarity [2:1] 0x27 Read/Write *****00* Power-Down Pin Function [0] *******0 Power-Down [7] 1******* Auto Power-Down Enable [6] *0****** HDCP A0 [5] **0***** MCLK External Enable [4] ***0**** BT656 EN [3] [2:0] ****0*** *****000 Force DE Generation Interlace Offset Description Output field polarity. 0 = active low out. 1 = active high out. 0 = Don’t invert clock out. 1 = Invert clock out. Selects which clock to use on output pin. 1× CLK is divided down from TMDS clock input when pixel repetition is in use. 00 = ½× CLK. 01 = 1× CLK. 10 = 2× CLK. 11 = 90° phase 1× CLK. Sets the drive strength of the outputs. 00 = lowest, 11 = highest. Selects which pins the data comes out on. 00 = 4:4:4 mode (normal). 01 = 4:2:2 + DDR 4:2:2 on blue. 10 = DDR 4:4:4 + DDR 4:2:2 on blue. Enables primary output. Enables secondary output (DDR 4:2:2 in Output Mode 1 and Mode 2). Three-state the outputs. Three-state the SPDIF output. Three-state the I2S output and the MCLK out. Sets polarity of power-down pin. 0 = active low. 1 = active high. Selects the function of the power-down pin. 00 = power-down. 01 = power-down and three-state SOG. 10 = three-state outputs only. 11 = three-state outputs and SOG. 0 = normal. 1 = power-down. 0 = disable auto low power state. 1 = enable auto low power state. Sets the LSB of the address of the HDCP I2C. Set to 1 only for a second receiver in a dual-link configuration. 0 = use internally generated MCLK. 1 = use external MCLK input. If an external MCLK is used, it must be locked to the video clock according to the CTS and N available in the I2C. Any mismatch between the internal MCLK and the input MCLK results in dropped or repeated audio samples. Enables EAV/SAV codes to be inserted into the video output data. Allows use of the internal DE generator in DVI mode. Sets the difference (in HSYNCs) in field length between Field 0 and Field 1. Rev. 0 | Page 14 of 28 AD9397 Hex Address 0x28 Read/Write or Read Only Read/Write Bits [7:2] Default Value 011000** Register Name VS Delay 0x29 Read/Write [1:0] [7:0] ******01 00000100 HS Delay MSB HS Delay 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F Read/Write Read/Write Read/Write Read/Write Read/Write Read 0x30 Read [3:0] [7:0] [3:0] [7:0] [7] [6] [5] [3] [2:0] [6] ****0101 00000000 ****0010 11010000 0******* *0****** **0***** ****0*** *****000 *0****** Line Width MSB Line Width Screen Height MSB Screen Height Test 1 TMDS Sync Detect TMDS Active HDCP Keys Read DVI Quality DVI Content Encrypted Read/Write [5] [4] [7:4] **0***** ***0**** 1001**** DVI HSYNC Polarity DVI VSYNC Polarity MV Pulse Max [3:0] ****0110 MV Pulse Min Read/Write [7] 0******* MV Oversample En Read/Write [6] [5:0] [7] *0****** **001101 1******* MV Pal En MV Line Count Start MV Detect Mode [6] *0****** MV Settings Override [5:0] [7:6] **010101 10****** MV Line Count End MV Pulse Limit Set [5] **0***** Low Freq Mode [4] ***0**** Low Freq Override [3] ****0*** Up Conversion Mode [2] [1] *****0** ******0* CrCb Filter Enable CSC_Enable [6:5] *01* **** CSC_Mode [4:0] ***01100 CSC_Coeff_A1 MSB 0x31 0x32 0x33 0x34 0x35 Read/Write Read/Write Description Sets the delay (in lines) from the VSYNC leading edge to the start of active video. MSB, Register 0x29. Sets the delay (in pixels) from the HSYNC leading edge to the start of active video. MSB, Register 0x2B. Sets the width of the active video line in pixels. MSB, Register 0x2D. Sets the height of the active screen in lines. Must be written to 1 for proper operation. Detects a TMDS DE. Detects a TMDS clock. Returns 1 when read of EEPROM keys is successful. Returns quality number based on DE edges. This bit is high when HDCP decryption is in use (content is protected). The signal goes low when HDCP is not being used. Customers can use this bit to determine whether to allow copying of the content. The bit should be sampled at regular intervals because it can change on a frame-by-frame basis. Returns DVI HSYNC polarity. Returns DVI VSYNC polarity. Sets the maximum pseudo sync pulse width for Macrovision detection. Sets the minimum pseudo sync pulse width for Macrovision® detection. Tells the Macrovision detection engine whether we are oversampling or not. Tells the Macrovision detection engine to enter PAL mode. Sets the start line for Macrovision detection. 0 = standard definition. 1 = progressive scan mode. 0 = use hard-coded settings for line counts and pulse widths. 1 = use I2C values for these settings. Sets the end line for Macrovision detection. Sets the number of pulses required in the last 3 lines (SD mode only). Sets audio PLL to low frequency mode. Low frequency mode should only be set for pixel clocks <80 MHz. Allows the previous bit to be used to set low frequency mode rather than the internal auto-detect. 0 = repeat Cr and Cb values. 1 = interpolate Cr and Cb values. Enables the FIR filter for 4:2:2 CrCb output. Enables the color space converter (CSC). The default settings for the CSC provide HDTV-to-RGB conversion. Sets the fixed point position of the CSC coefficients, including the A4, B4, and C4 offsets. 00 = ±1.0, −4096 to +4095. 01 =±2.0, −8192 to +8190. 1× = ±4.0, −16384 to +16380. MSB, Register 0x36. Rev. 0 | Page 15 of 28 AD9397 Hex Address Read/Write or Read Only Bits Default Value Register Name Description 0x36 Read/Write [7:0] 01010010 CSC_Coeff_A1 LSB 0x37 0x38 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_A2 MSB CSC_Coeff_A2 LSB 0x39 0x3A Read/Write Read/Write [4:0] [7:0] ***00000 00000000 CSC_Coeff_A3 MSB CSC_Coeff_A3 LSB 0x3B 0x3C Read/Write Read/Write [4:0] [7:0] ***11001 11010111 CSC_Coeff_A4 MSB CSC_Coeff_A4 LSB 0x3D 0x3E Read/Write Read/Write [4:0] [7:0] ***11100 01010100 CSC_Coeff_B1 MSB CSC_Coeff_B1 LSB 0x3F 0x40 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_B2 MSB CSC_Coeff_B2 LSB 0x41 0x42 Read/Write Read/Write [4:0] [7:0] ***11110 10001001 CSC_Coeff_B3 MSB CSC_Coeff_B3 0x43 0x44 Read/Write Read/Write [4:0] [7:0] ***00010 10010010 CSC_Coeff_B4 MSB CSC_Coeff_B4 LSB 0x45 0x46 Read/Write Read/Write [4:0] [7:0] ***00000 00000000 CSC_Coeff_C1 MSB CSC_Coeff_C1 LSB 0x47 0x48 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_C2 MSB CSC_Coeff_C2 LSB Color space converter (CSC) coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x38. CSC coefficient for equation: ROUT = (A1 × RIN + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x3A. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x3C. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x3E. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x40. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x42. CSC coefficient for equation: ROUT = (A1 × RIN + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x44. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × RIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x46. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x48. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 B B B B B B B B B B Rev. 0 | Page 16 of 28 AD9397 Hex Address 0x49 0x4A Read/Write or Read Only Read/Write Read/Write Bits [4:0] [7:0] Default Value ***01110 10000111 Register Name CSC_Coeff_C3 MSB CSC_Coeff_C3 LSB 0x4B 0x4C Read/Write Read/Write [4:0] [7:0] ***11000 10111101 CSC_Coeff_C4 MSB CSC_Coeff_C4 LSB 0x50 0x56 0x59 Read/Write Read/Write Read/Write [7:0] [7:0] [6] [5] [4] [0] 00100000 00001111 Test Test MDA/MCL PU CLK Term O/R Manual CLK Term MDA/MCL ThreeState Description MSB, Register 0x4A. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 MSB, Register 0x4C. CSC coefficient for equation: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 Must be written to 0x20 for proper operation. Must be written to default of 0x0F for proper operation. This disables the MDA/MCL pull-ups. Clock termination power-down override: 0 = auto, 1 = manual. Clock termination: 0 = normal, 1 = disconnected. This bit three-states the MDA/MCL lines. B B Rev. 0 | Page 17 of 28 AD9397 2-WIRE SERIAL CONTROL REGISTER DETAILS CHIP IDENTIFICATION 0x12—Bit[4] VSYNC Polarity Override 0x00—Bit[7:0] Chip Revision 0 = auto VSYNC polarity, 1 = manual VSYNC polarity. Manual VSYNC polarity is defined in Register 0x11, Bit 5. The powerup default is 0. An 8-bit value that reflects the current chip revision. 0x11—Bit[7] HSYNC Source 0x17—Bits[3:0] HSYNCs per VSYNC MSBs 0 = HSYNC, 1 = SOG. The power-up default is 0. These selections are ignored if Register 0x11, Bit 6 = 0. The 4 MSBs of the 12-bit counter that reports the number of HSYNCs/VSYNC on the active input. This is useful in determining the mode and aids in setting the PLL divide ratio. 0x11—Bit[6] HSYNC Source Override 0 = auto HSYNC source, 1 = manual HSYNC source. Manual HSYNC source is defined in Register 0x11, Bit 7. The power-up default is 0. 0x11—Bit[5] VSYNC Source 0 = VSYNC, 1 = VSYNC from SOG. The power-up default is 0. These selections are ignored if Register 0x11, Bit 4 = 0. 0x11—Bit[4] VSYNC Source Override 0 = auto VSYNC source, 1 = manual VSYNC source. Manual VSYNC source is defined in Register 0x11, Bit 5. The power-up default is 0. 0x11—Bit[3] Channel Select 0 = Channel 0, 1 = Channel 1. The power-up default is 0. These selections are ignored if Register 0x11, Bit 2 = 0. 0x11—Bit[2] Channel Select Override 0 = auto channel select, 1 = manual channel select. Manual channel select is defined in Register 0x11, Bit 3. The power-up default is 0. 0x11—Bit[1] Interface Select 0 = analog interface, 1 = digital interface. The power-up default is 0. These selections are ignored if Register 0x11, Bit 0 = 0. 0x11—Bit[0] Interface Select Override 0 = auto interface select, 1 = manual interface select. Manual interface select is defined in Register 0x11, Bit 1. The power-up default is 0. 0x12—Bit[7] Input HSYNC Polarity 0 = active low, 1 = active high. The power-up default is 1. These selections are ignored if Register 10x2, Bit 6 = 0. 0x18—Bit[7:0] HSYNCs per VSYNC LSBs The 8 LSBs of the 12-bit counter that reports the number of HSYNCs/VSYNC on the active input. 0x21—Bit[5] VSYNC Filter Enable The purpose of the VSYNC filter is to guarantee the position of the VSYNC edge with respect to the HSYNC edge and to generate a field signal. The filter works by examining the placement of VSYNC and regenerating a correctly placed VSYNC one line later. The VSYNC is first checked to see whether it occurs in the Field 0 position or the Field 1 position. This is done by checking the leading edge position against the sync separator threshold and the HSYNC position. The HSYNC width is divided into four quadrants with Quadrant 1 starting at the HSYNC leading edge plus a sync separator threshold. If the VSYNC leading edge occurs in Quadrant 1 or Quadrant 4, the field is set to 0 and the output VSYNC is placed coincident with the HSYNC leading edge. If the VSYNC leading edge occurs in Quadrant 2 or Quadrant 3, the field is set to 1 and the output VSYNC leading edge is placed in the center of the line. In this way, the VSYNC filter creates a predictable relative position between HSYNC and VSYNC edges at the output. If the VSYNC occurs near the HSYNC edge, this guarantees that the VSYNC edge follows the HSYNC edge. This performs filtering also in that it requires a minimum of 64 lines between VSYNCs. The VSYNC filter cleans up extraneous pulses that might occur on the VSYNC. This should be enabled whenever the HSYNC/VSYNC count is used. Setting this bit to 0 disables the VSYNC filter. Setting this bit to 1 enables the VSYNC filter. Power-up default is 0. 0x21—Bit[4] VSYNC Duration Enable 0 = auto HSYNC polarity, 1 = manual HSYNC polarity. Manual HSYNC polarity is defined in Register 0x11, Bit 7. The powerup default is 0. This enables the VSYNC duration block which is designed to be used with the VSYNC filter. Setting the bit to 0 leaves the VSYNC output duration unchanged; setting the bit to 1 sets the VSYNC output duration based on Register 0x22. The power-up default is 0. 0x12—Bit[5] Input VSYNC Polarity 0x22—Bits[7:0] VSYNC Duration 0 = active low, 1 = active high. The power-up default is 1. These selections are ignored if Register 0x11, Bit 4 = 0. This is used to set the output duration of the VSYNC, and is designed to be used with the VSYNC filter. This is valid only if Register 0x21, Bit 4 is set to 1. Power-up default is 4. 0x12—Bit[6] HSYNC Polarity Override Rev. 0 | Page 18 of 28 AD9397 0x23—Bit[7:0] HSYNC Duration 0x25—Bit[5:4] Output Drive Strength An 8-bit register that sets the duration of the HSYNC output pulse. The leading edge of the HSYNC output is triggered by the internally generated, phase-adjusted PLL feedback clock. The AD9397 then counts a number of pixel clocks equal to the value in this register. This triggers the trailing edge of the HSYNC output, which is also phase-adjusted. The power-up default is 32. These two bits select the drive strength for all the high speed digital outputs (except VSOUT, A0 and O/E field). Higher drive strength results in faster rise/fall times and in general makes it easier to capture data. Lower drive strength results in slower rise/fall times and helps to reduce EMI and digitally generated power supply noise. The power-up default setting is 11. 0x24—Bit[7] HSYNC Output Polarity Output Drive 00 01 10 11 This bit sets the polarity of the HSYNC output. Setting this bit to 0 sets the HSYNC output to active low. Setting this bit to 1 sets the HSYNC output to active high. Power-up default setting is 1. 0x24—Bit[6] VSYNC Output Polarity This bit sets the polarity of the VSYNC output (both DVI and analog). Setting this bit to 0 sets the VSYNC output to active low. Setting this bit to 1 sets the VSYNC output to active high. Power-up default is 1. 0x24—Bit[5] Display Enable Output Polarity This bit sets the polarity of the display enable (DE) for both DVI and analog. 0 = DE output polarity is negative. 1 = DE output polarity is positive. The power-up default is 1. Table 12. Output Drive Strength Result Low output drive strength Medium low output drive strength Medium high output drive strength High output drive strength 0x25—Bits[3:2] Output Mode These bits choose between four options for the output mode, one of which is exclusive to an HDMI input. 4:4:4 mode is standard RGB; 4:2:2 mode is YCrCb, which reduces the number of active output pins from 24 to 16; 4:4:4 is double data rate (DDR) output mode; and the data is RGB mode, but changes on every clock edge. The power-up default setting is 00. Table 13. Output Mode 0x24—Bit[4] Field Output Polarity This bit sets the polarity of the field output signal (both DVI and analog) on Pin 21. 0 = active low out = even field; active high = odd field. 1 = active high out = odd field; active high = even field. The power-up default is 1. 0x24—Bit[0] Output Clock Invert This bit allows inversion of the output clock as specified by Register 0x25, Bits 7 to 6. 0 = noninverted clock. 1 = inverted clock. The power-up default setting is 0. Output Mode 00 01 10 11 Result 4:4:4 RGB mode 4:2:2 YCrCb mode + DDR 4:2:2 on blue (secondary) DDR 4:4:4: DDR mode + DDR 4:2:2 on blue (secondary) 12-bit 4:2:2 (HDMI option only) 0x25—Bit[1] Primary Output Enable These bits select the clock output on the DATACLK pin. They include 1/2× clock, a 2× clock, a 90° phase shifted clock, or the normal pixel clock. The power-up default setting is 01. This bit places the primary output in active or high impedance mode. The primary output is designated when using either 4:2:2 or DDR 4:4:4. In these modes, the data on the red and green output channels is the primary output, while the output data on the blue channel (DDR YCrCb) is the secondary output. 0 = primary output is in high impedance mode. 1 = primary output is enabled. The power-up default setting is 1. Table 11. Output Clock Select 0x25—Bit[0] Secondary Output Enable Select 00 01 10 11 This bit places the secondary output in active or high impedance mode. The secondary output is designated when using either 4:2:2 or DDR 4:4:4. In these modes, the data on the blue output channel is the secondary output while the output data on the red and green channels is the primary output. Secondary output is always a DDR YCrCb data mode. The power-up default setting is 0. 0 = secondary output is in high impedance mode. 1 = secondary output is enabled. 0x25—Bits[7:6] Output Clock Select Result ½× pixel clock 1× pixel clock 2× pixel clock 90° phase 1× pixel clock Rev. 0 | Page 19 of 28 AD9397 0x26—Bit[7] Output Three-State 0x27—Bit[3] Force DE Generation When enabled, this bit puts all outputs (except SOGOUT) in a high impedance state. 0 = normal outputs. 1 = all outputs (except SOGOUT) in high impedance mode. The power-up default setting is 0. This bit allows the use of the internal DE generator in DVI mode. 0 = internal DE generation disabled. 1 = force DE generation via programmed registers. The power-up default setting is 0. 0x26—Bit[3] Power-Down Polarity 0x27—Bits[2:0] Interlace Offset This bit defines the polarity of the input power-down pin. 0 = power-down pin is active low. 1 = power-down pin is active high. The power-up default setting is 1. These bits define the offset in HSYNCs from Field 0 to Field 1. The power-up default setting is 000. 0x26—Bits[2:1] Power-Down Pin Function These bits set the delay (in lines) from the leading edge of VSYNC to active video. The power-up default setting is 24. These bits define the different operational modes of the powerdown pin. These bits are functional only when the power-down pin is active; when it is not active, the part is powered up and functioning. 0x = the chip is powered down and all outputs are in high impedance mode. 1x = the chip remains powered up, but all outputs are in high impedance mode. The power-up default setting is 00. 0x28—Bits[7:2] VSYNC Delay 0x28—Bit[1:0] HSYNC Delay MSBs These 2 bits and the following 8 bits set the delay (in pixels) from the HSYNC leading edge to the start of active video. The power-up default setting is 0x104. 0x29—Bits[7:0] HSYNC Delay LSBs 0x26—Bit[0] Power-Down See the HSYNC Delay MSBs section. This bit is used to put the chip in power-down mode. In this mode, the power dissipation is reduced to a fraction of the typical power (see Table 1 for exact power dissipation). When in power-down, the HSOUT, VSOUT, DATACK, and all 30 of the data outputs are put into a high impedance state. Note that the SOGOUT output is not put into high impedance. Circuit blocks that continue to be active during power-down include the voltage references, sync processing, sync detection, and the serial register. These blocks facilitate a fast start-up from powerdown. 0 = normal operation. 1 = power-down. The power-up default setting is 0. 0x2A—Bits[3:0] Line Width MSBs 0x27—Bit[7] Auto Power-Down Enable These 4 bits and the following 8 bits set the width of the active video line (in pixels). The power-up default setting is 0x500. 0x2B—Bits[7:0] Line Width LSBs See the line width MSBs section. 0x2C—Bits[3:0] Screen Height MSBs These 4 bits and the following 8 bits set the height of the active screen (in lines). The power-up default setting is 0x2D0. 0x2D—Bits[7:0] Screen Height LSBs See the Screen Height MSBs section. This bit enables the chip to go into low power mode, or seek mode if no sync inputs are detected. 0 = auto power-down disabled. 1 = chip powers down if no sync inputs present. The power-up default setting is 1. 0x2F—Bit[6] TMDS Sync Detect This read-only bit indicates the presence of a TMDS DE. 0 = no TMDS DE present. 1 = TMDS DE detected. 0x2F—Bit[5] TMDS Active 0x27—Bit[6] HDCP A0 Address 2 This bit sets the LSB of the address of the HDCP I C. This should be set to 1 only for a second receiver in a dual-link configuration. The power-up default is 0. This read-only bit indicates the presence of a TMDS clock. 0 = no TMDS clock present. 1 = TMDS clock detected. BT656 GENERATION This read-only bit reports if the HDCP keys were read successfully. 0 = failure to read HDCP keys. 1 = HDCP keys read. 0x2F—Bit[3] HDCP Keys Read 0x27—Bit[4] BT656 Enable This bit enables the output to be BT656 compatible with the defined start of active video (SAV) and end of active video (EAV) controls to be inserted. These require specification of the number of active lines, active pixels per line, and delays to place these markers. 0 = disable BT656 video mode. 1 = enable BT656 video mode. The power-up default setting is 0. 0x2F—Bits[2:0] DVI Quality These read-only bits indicate a level of DVI quality based on the DE edges. A larger number indicates a higher quality. Rev. 0 | Page 20 of 28 AD9397 0x30—Bit[6] DVI Content Encrypted 0x33—Bits[5:0] Macrovision Line Count End This read-only bit is high when HDCP decryption is in use (content is protected). The signal goes low when HDCP is not being used. Customers can use this bit to allow copying of the content. The bit should be sampled at regular intervals because it can change on a frame-by-frame basis. 0 = HDCP not in use. 1 = HDCP decryption in use. Set the end line for Macrovision detection. Along with Register 0x32, Bits [5:0], they define the region where MV pulses are expected to occur. The power-up default is Line 21. 0x30—Bit[5] DVI HSYNC Polarity 0x34—Bits[7:6] Macrovision Pulse Limit Select Set the number of pulses required in the last three lines (SD mode only). If there is not at least this number of MV pulses, the engine stops. These two bits define these pulse counts: This read-only bit indicates the polarity of the DVI HSYNC. 0 = DVI HSYNC polarity is low active. 1 = DVI HSYNC polarity is high active. 00 = 6. 01 = 4. 10 = 5 (default). 11 = 7. 0x30—Bit[4] DVI VSYNC Polarity This read-only bit indicates the polarity of the DVI VSYNC. 0 = DVI VSYNC polarity is low active. 1 = DVI VSYNC polarity is high active. MACROVISION 0x34—Bit[5] Low Frequency Mode Sets whether the audio PLL is in low frequency mode or not. Low frequency mode should only be set for pixel clocks <80 MHz. 0x31—Bits[7:4] Macrovision Pulse Max 0x34—Bit[4] Low Frequency Override These bits set the pseudo sync pulse width maximum for Macrovision detection in pixel clocks. This is functional for 13.5 MHz SDTV or 27 MHz progressive scan. Power-up default is 9. Allows the previous bit to be used to set low frequency mode rather than the internal autodetect. 0x34—Bit[3] Upconversion Mode 0 = repeat Cb/Cr values. 1 = interpolate Cb/Cr values. 0x31—Bits[3:0] Macrovision Pulse Min 0x34—Bit[2] CbCr Filter Enable These bits set the pseudo sync pulse width maximum for Macrovision detection in pixel clocks. This is functional for 13.5 MHz SDTV or 27 MHz progressive scan. Power up default is 6. Enables the FIR filter for 4:2:2 CbCr output. COLOR SPACE CONVERSION 0x32—Bit[7] Macrovision Oversample Enable Tells the Macrovision detection engine whether oversampling is used. This accommodates 27 MHz sampling for SDTV and 54 MHz sampling for progressive scan and is used as a correction factor for clock counts. Power-up default is 0. 0x32—Bit[6] Macrovision PAL Enable Tells the Macrovision detection engine to enter PAL mode when set to 1. Default is 0 for NTSC mode. 0x32—Bits[5:0] Macrovision Line Count Start Set the start line for Macrovision detection. Along with Register 0x33, Bits [5:0], they define the region where MV pulses are expected to occur. The power-up default is Line 13. 0x33—Bit[7] Macrovision Detect Mode 0 = standard definition. 1 = progressive scan mode The default power-up values for the color space converter coefficients (R0x35 through R0x4C) are set for ATSC RGB-toYCbCr conversion. They are completely programmable for other conversions. 0x34—Bit[1] Color Space Converter Enable This bit enables the color space converter. 0 = disable color space converter. 1 = enable color space converter. The power-up default setting is 0. 0x35—Bits[6:5] Color Space Converter Mode These two bits set the fixed-point position of the CSC coefficients, including the A4, B4, and C4 offsets. Default = 01. Table 14. CSC Fixed Point Converter Mode Select 00 01 1× 0x33—Bit[6] Macrovision Settings Override This defines whether preset values are used for the MV line counts and pulse widths or the values stored in I2C registers are used. 0 = use hard-coded settings for line counts and pulse widths. 1 = use I2C values for these settings. Rev. 0 | Page 21 of 28 Result ±1.0, −4096 to +4095 ±2.0, −8192 to +8190 ±4.0, −16384 to +16380 AD9397 0x35—Bits[4:0] Color Space Conversion Coefficient A1 MSBs These 5 bits form the 5 MSBs of the Color Space Conversion Coefficient A1. This combined with the 8 LSBs of the following register form a 13-bit, twos complement coefficient which is user programmable. The equation takes the form of: ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 0x37—Bits[4:0] CSC A2 MSBs These five bits form the 5 MSBs of the Color Space Conversion Coefficient A2. Combined with the 8 LSBs of the following register they form a 13-bit, twos complement coefficient that is user programmable. The equation takes the form of: See the Register 0x37 section. 0x39—Bits[4:0] CSC A3 MSBs The default value for the 13-bit A3 is 0x0000. 0x3A—Bits[7:0] CSC A3 LSBs 0x3B—Bits[4:0] CSC A4 MSBs The default value for the 13-bit A4 is 0x19D7. 0x3C—Bits[7:0] CSC A4 LSBs 0x3D—Bits[4:0] CSC B1 MSBs The default value for the 13-bit B1 is 0x1C54. 0x3E—Bits[7:0] CSC B1 LSBs 0x3F—Bits[4:0] CSC B2 MSBs The default value for the 13-bit C1 is 0x0000. 0x46—Bits[7:0] CSC C1 LSBs 0x47—Bits[4:0] CSC C2 MSBs See the Register 0x35 section. 0x38—Bits[7:0] CSC A2 LSBs 0x42—Bit[7:0] CSC B3 LSBs 0x43—Bit[4:0] CSC B4 MSBs 0x44—Bits[7:0] CSC B4 LSBs 0x45—Bits[4:0] CSC C1 MSBs 0x36—Bits[7:0] Color Space Conversion Coefficient A1 LSBs The default value for the 13-bit A2 coefficient is 0x0800. The default value for the 13-bit B3 is 0x1E89. The default value for the 13-bit B4 is 0x0291. The default value for the 13-bit A1 coefficient is 0x0C52. ROUT = (A1 × RIN) + (A2 × GIN) + (A3 × BIN) + A4 GOUT = (B1 × RIN) + (B2 × GIN) + (B3 × BIN) + B4 BOUT = (C1 × RIN) + (C2 × GIN) + (C3 × BIN) + C4 0x40—Bits[7:0] CSC B2 LSBs 0x41—Bits[4:0] CSC B3 MSBs The default value for the 13-bit C2 is 0x0800. 0x48—Bits[7:0] CSC C2 LSBs 0x49—Bits[4:0] CSC C3 MSBs The default value for the 13-bit C3 is 0x0E87. 0x4A—Bits[7:0] CSC C3 LSBs 0x4B—Bits[4:0] CSC C4 MSBs The default value for the 13-bit C4 is 0x18BD. 0x4C—Bits[7:0] CSC C4 LSBs 0x59—Bit[6] MDA/MCL PU Disable This bit disables the inter-MDA/MCL pull-ups. 0x59—Bit[5] CLK Term O/R This bit allows for overriding during power down. 0 = auto, 1 = manual. 0x59—Bit[4] Manual CLK Term This bit allows normal clock termination or disconnects this. 0 = normal, 1 = disconnected. 0x59—Bit[0] MDA/MCL Three-State This bit three-states the MDA/MCL lines to allow in-circuit programming of the EEPROM. The default value for the 13-bit B2 is 0x0800. Rev. 0 | Page 22 of 28 AD9397 2-WIRE SERIAL CONTROL PORT DATA TRANSFER VIA SERIAL INTERFACE A 2-wire serial interface control interface is provided in the AD9397. Up to two AD9397 devices can be connected to the 2-wire serial interface, with a unique address for each device. The 2-wire serial interface comprises a clock (SCL) and a bidirectional data (SDA) pin. The analog flat panel interface acts as a slave for receiving and transmitting data over the serial interface. When the serial interface is not active, the logic levels on SCL and SDA are pulled high by external pull-up resistors. Data received or transmitted on the SDA line must be stable for the duration of the positive-going SCL pulse. Data on SDA must change only when SCL is low. If SDA changes state while SCL is high, the serial interface interprets that action as a start or stop sequence. There are six components to serial bus operation: For each byte of data read or written, the MSB is the first bit of the sequence. If the AD9397 does not acknowledge the master device during a write sequence, the SDA remains high so the master can generate a stop signal. If the master device does not acknowledge the AD9397 during a read sequence, the AD9397 interprets this as the end of data. The SDA remains high, so the master can generate a stop signal. To write data to specific control registers of the AD9397, the 8-bit address of the control register of interest must be written after the slave address has been established. This control register address is the base address for subsequent write operations. The base address auto-increments by 1 for each byte of data written after the data byte intended for the base address. If more bytes are transferred than there are available addresses, the address does not increment and remains at its maximum value. Any base address higher than the maximum value does not produce an acknowledge signal. • Start signal • Slave address byte • Base register address byte • Data byte to read or write • Stop signal Data are read from the control registers of the AD9397 in a similar manner. Reading requires two data transfer operations: • Acknowledge (Ack) • The base address must be written with the R/W bit of the slave address byte low to set up a sequential read operation. • Reading (the R/W bit of the slave address byte high) begins at the previously established base address. The address of the read register auto-increments after each byte is transferred. When the serial interface is inactive (SCL and SDA are high), communications are initiated by sending a start signal. The start signal is a high-to-low transition on SDA while SCL is high. This signal alerts all slave devices that a data transfer sequence is coming. The first 8 bits of data transferred after a start signal comprise a 7-bit slave address (the first 7 bits) and a single R/W bit (the eighth bit). The R/W bit indicates the direction of data transfer, read from (1) or write to (0) the slave device. If the transmitted slave address matches the address of the device (set by the state of the SA0 input pin as shown in Table 15), the AD9397 acknowledges by bringing SDA low on the 9th SCL pulse. If the addresses do not match, the AD9397 does not acknowledge. Table 15. Serial Port Addresses Bit 6 A5 0 Bit 5 A4 0 Bit 4 A3 1 Bit 3 A2 1 Bit 2 A1 0 Bit 1 A0 0 A repeated start signal occurs when the master device driving the serial interface generates a start signal without first generating a stop signal to terminate the current communication. This is used to change the mode of communication (read, write) between the slave and master without releasing the serial interface lines. SDA tBUFF tSTAH tDSU tDHO tSTASU tSTOSU tDAL SCL 05691-007 Bit 7 A6 (MSB) 1 To terminate a read/write sequence to the AD9397, a stop signal must be sent. A stop signal comprises a low-to-high transition of SDA while SCL is high. tDAH Figure 7. Serial Port Read/Write Timing Rev. 0 | Page 23 of 28 AD9397 SERIAL INTERFACE READ/WRITE EXAMPLES Write to one control register: Read from one control register: • Start signal • Start signal • Slave address byte (R/W bit = low) • Slave address byte (R/W bit = low) • Base address byte • Base address byte • Data byte to base address • Start signal • Stop signal • Slave address byte (R/W bit = high) Write to four consecutive control registers: • Data byte from base address • Start signal • Stop signal • Slave address byte (R/W bit = low) Read from four consecutive control registers: • Base address byte • Start signal • Data byte to base address • Slave address byte (R/W bit = low) • Data byte to (base address + 1) • Base address byte • Data byte to (base address + 2) • Start signal • Data byte to (base address + 3) • Slave address byte (R/W bit = high) • Stop signal • Data byte from base address • Data byte from (base address + 1) • Data byte from (base address + 2) • Data byte from (base address + 3) • Stop signal BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 ACK 05691-008 SDA SCL Figure 8. Serial Interface—Typical Byte Transfer Rev. 0 | Page 24 of 28 AD9397 PCB LAYOUT RECOMMENDATIONS The AD9397 is a high precision, high speed digital device. To achieve the maximum performance from the part, it is important to have a well laid-out board. The following is a guide for designing a board using the AD9397. POWER SUPPLY BYPASSING It is recommended to bypass each power supply pin with a 0.1 μF capacitor. The exception is in the case where two or more supply pins are adjacent to each other. For these groupings of powers/grounds, it is only necessary to have one bypass capacitor. The fundamental idea is to have a bypass capacitor within about 0.5 cm of each power pin. Also, avoid placing the capacitor on the opposite side of the PC board from the AD9397, because that interposes resistive vias in the path. The bypass capacitors should be physically located between the power plane and the power pin. Current should flow from the power plane to the capacitor to the power pin. Do not make the power connection between the capacitor and the power pin. Placing a via underneath the capacitor pads down to the power plane is generally the best approach. In some cases, using separate ground planes is unavoidable, so it is recommend to place a single ground plane under the AD9397. The location of the split should be at the receiver of the digital outputs. In this case, it is even more important to place components wisely because the current loops are much longer (current takes the path of least resistance). An example of a current loop is: power plane to AD9397 to digital output trace to digital data receiver to digital ground plane. OUTPUTS (BOTH DATA AND CLOCKS) Try to minimize the trace length that the digital outputs have to drive. Longer traces have higher capacitance, which require more current that causes more internal digital noise. Shorter traces reduce the possibility of reflections. Adding a 50 Ω to 200 Ω series resistor can suppress reflections, reduce EMI, and reduce the current spikes inside the AD9397. If series resistors are used, place them as close as possible to the AD9397 pins (although try not to add vias or extra length to the output trace to move the resistors closer). It is particularly important to maintain low noise and good stability of PVDD (the clock generator supply). Abrupt changes in PVDD can result in similarly abrupt changes in sampling clock phase and frequency. This can be avoided by careful attention to regulation, filtering, and bypassing. It is highly desirable to provide separate regulated supplies for each of the analog circuitry groups (VD and PVDD). If possible, limit the capacitance that each of the digital outputs drives to less than 10 pF. This can be accomplished easily by keeping traces short and by connecting the outputs to only one device. Loading the outputs with excessive capacitance increases the current transients inside of the AD9397 and creates more digital noise on its power supplies. Some graphic controllers use substantially different levels of power when active (during active picture time) and when idle (during HSYNC and VSYNC periods). This can result in a measurable change in the voltage supplied to the analog supply regulator, which can in turn produce changes in the regulated analog supply voltage. This can be mitigated by regulating the analog supply, or at least PVDD, from a different, cleaner power source (for example, from a 12 V supply). The digital inputs on the AD9397 were designed to work with 3.3 V signals, but are tolerant of 5.0 V signals. Therefore, no extra components need to be added if using 5.0 V logic. DIGITAL INPUTS Any noise that enters the HSYNC input trace can add jitter to the system. Therefore, minimize the trace length and do not run any digital or other high frequency traces near it. It is recommended to use a single ground plane for the entire board. Experience has repeatedly shown that the noise performance is the same or better with a single ground plane. Using multiple ground planes can be detrimental because each separate ground plane is smaller and long ground loops can result. Rev. 0 | Page 25 of 28 AD9397 COLOR SPACE CONVERTER (CSC) COMMON SETTINGS Table 16. HDTV YCrCb (0 to 255) to RGB (0 to 255) (Default Setting for AD9397) Register Address Value Register Address Value Register Address Value 0x35 0x2C 0x3D 0x1C 0x45 0x00 Red/Cr Coeff 1 0x36 0x52 Green/Y Coeff 1 0x3E 0x54 Blue/Cb Coeff 1 0x46 0x00 0x37 0x08 0x3F 0x08 0x47 0x08 Red/Cr Coeff 2 0x38 0x00 Green/Y Coeff 2 0x40 0x00 Blue/Cb Coeff 2 0x48 0x00 0x39 0x00 0x41 0x3E 0x49 0x0E Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x89 Blue/Cb Coeff 3 0x4A 0x87 0x3B 0x19 0x43 0x02 0x4B 0x18 Red/Cr Offset 0x3C 0xD7 Green/Y Offset 0x44 0x91 Blue/Cb Offset 0x4C 0xBD Table 17. HDTV YCrCb (16 to 235) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x47 0x3D 0x1D 0x45 0x00 Red/Cr Coeff 1 0x36 0x2C Green/Y Coeff 1 0x3E 0xDD Blue/Cb Coeff 1 0x46 0x00 0x37 0x04 0x3F 0x04 0x47 0x04 Red/Cr Coeff 2 0x38 0xA8 Green/Y Coeff 2 0x40 0xA8 Blue/Cb Coeff 2 0x48 0xA8 0x39 0x00 0x41 0x1F 0x49 0x08 Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x26 Blue/Cb Coeff 3 0x4A 0x 75 0x3B 0x1C 0x43 0x01 0x4B 0x1B Red/Cr Offset 0x3C 0x1F Green/Y Offset 0x44 0x34 Blue/Cb Offset 0x4C 0x7B Table 18. SDTV YCrCb (0 to 255) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value Red/Cr Coeff 1 0x36 0xF8 Green/Y Coeff 1 0x3D 0x3E 0x1A 0x6A Blue/Cb Coeff. 1 0x45 0x46 0x00 0x00 0x35 0x2A 0x37 0x08 0x3F 0x08 0x47 0x08 Red/Cr Coeff 2 0x38 0x00 Green/Y Coeff 2 0x40 0x00 Blue/Cb Coeff 2 0x48 0x00 0x39 0x00 0x41 0x1D 0x49 0x0D Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x50 Blue/Cb Coeff 3 0x4A 0xDB 0x3B 0x1A 0x43 0x04 0x4B 0x19 Red/Cr Offset 0x3C 0x84 Green/Y Offset 0x44 0x23 Blue/Cb Offset 0x4C 0x12 Table 19. SDTV YCrCb (16 to 235) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x46 0x3D 0x1C 0x45 0x00 Red/Cr Coeff 1 0x36 0x63 Green/Y Coeff 1 0x3E 0xC0 Blue/Cb Coeff 1 0x46 0x00 0x37 0x04 0x3F 0x04 0x47 0x04 Red/Cr Coeff 2 0x38 0xA8 Green/Y Coeff 2 0x40 0xA8 Blue/Cb Coeff 2 0x48 0xA8 Rev. 0 | Page 26 of 28 0x39 0x00 0x41 0x1E 0x49 0x08 Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x6F Blue/Cb Coeff 3 0x4A 0x11 0x3B 0x1C 0x43 0x02 0x4B 0x1B Red/Cr Offset 0x3C 0x84 Green/Y Offset 0x44 0x1E Blue/Cb Offset 0x4C 0xAD AD9397 Table 20. RGB (0 to 255) to HDTV YCrCb (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x08 0x3D 0x03 0x45 0x1E Red/Cr Coeff 1 0x36 0x2D Green/Y Coeff 1 0x3E 0x68 Blue/Cb Coeff 1 0x46 0x21 0x37 0x18 0x3F 0x0B 0x47 0x19 Red/Cr Coeff 2 0x38 0x93 Green/Y Coeff 2 0x40 0x71 Blue/Cb Coeff 2 0x48 0xB2 0x39 0x1F 0x41 0x01 0x49 0x08 Red/Cr Coeff 0x3A 0x3F Green/Y Coeff 3 0x42 0x27 Blue/Cb Coeff 3 0x4A 0x2D 0x3B 0x08 0x43 0x00 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 21. RGB (0 to 255) to HDTV YCrCb (16 to 235) Register Address Value Register Address Value Register Address Value 0x35 0x07 0x3D 0x02 0x45 0x1E Red/Cr Coeff 1 0x36 0x06 Green/Y Coeff 1 0x3E 0xED Blue/Cb Coeff 1 0x46 0x64 0x37 0x19 0x3F 0x09 0x47 0x1A Red/Cr Coeff 2 0x38 0xA0 Green/Y Coeff 2 0x40 0xD3 Blue/Cb Coeff 2 0x48 0x96 0x39 0x1F 0x41 0x00 0x49 0x07 Red/Cr Coeff 3 0x3A 0x5B Green/Y Coeff 3 0x42 0xFD Blue/Cb Coeff 3 0x4A 0x06 0x3B 0x08 0x43 0x01 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 22. RGB (0 to 255) to SDTV YCrCb (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x08 0x3D 0x04 0x45 0x1D Red/Cr Coeff 1 0x36 0x2D Green/Y Coeff 1 0x3E 0xC9 Blue/Cb Coeff 1 0x46 0x3F 0x37 0x19 0x3F 0x09 0x47 0x1A Red/Cr Coeff 2 0x38 0x27 Green/Y Coeff 2 0x40 0x64 Blue/Cb Coeff 2 0x48 0x93 0x39 0x1E 0x41 0x01 0x49 0x08 Red/Cr Coeff 3 0x3A 0xAC Green/Y Coeff 3 0x42 0xD3 Blue/Cb Coeff 3 0x4A 0x2D 0x3B 0x08 0x43 0x00 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 23. RGB (0 to 255) to SDTV YCrCb (16 to 235) Register Address Value Register Address Value Register Address Value 0x35 0x07 0x3D 0x04 0x45 0x1D Red/Cr Coeff 1 0x36 0x06 Green/Y Coeff 1 0x3E 0x1C Blue/Cb Coeff 1 0x46 0xA3 0x37 0x1A 0x3F 0x08 0x47 0x1B Red/Cr Coeff 2 0x38 0x1E Green/Y Coeff 2 0x40 0x11 Blue/Cb Coeff 2 0x48 0x57 Rev. 0 | Page 27 of 28 0x39 0x1E 0x41 0x01 0x49 0x07 Red/Cr Coeff 3 0x3A 0xDC Green/Y Coeff 3 0x42 0x91 Blue/Cb Coeff 3 0x4A 0x06 0x3B 0x08 0x43 0x01 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 AD9397 OUTLINE DIMENSIONS 16.00 BSC SQ 1.60 MAX 0.75 0.60 0.45 100 1 76 75 PIN 1 14.00 BSC SQ TOP VIEW (PINS DOWN) 1.45 1.40 1.35 0.15 0.05 0.20 0.09 7° 3.5° 0° 0.08 MAX COPLANARITY SEATING PLANE 25 51 50 26 VIEW A 0.50 BSC LEAD PITCH VIEW A ROTATED 90° CCW 0.27 0.22 0.17 COMPLIANT TO JEDEC STANDARDS MS-026-BED Figure 9. 100-Lead Low Profile Quad Flat Package [LQFP] (ST-100) Dimensions shown in millimeters ORDERING GUIDE Model AD9397KSTZ-100 1 AD9397KSTZ-1501 AD9397/PCB 1 Max Speeds (MHz) Analog Digital 100 100 150 150 Temperature Range 0°C to 70°C 0°C to 70°C Package Description 100-Lead Low Profile Quad Flat Package (LQFP) 100-Lead Low Profile Quad Flat Package (LQFP) Evaluation Board Package Option ST-100 ST-100 Z = Pb-free part. © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05691-0-10/05(0) T T Rev. 0 | Page 28 of 28