a Quad Matched 741-Type Operational Amplifiers OP11 FEATURES Guaranteed VOS: 500 V Max Guaranteed Matched CMRR: 94 dB Min Guaranteed Matched VOS: 750 V Max LM148/LM348 Direct Replacement Low Noise Silicon-Nitride Passivation Internal Frequency Compensation Low Crossover Distortion Continuous Short-Circuit Protection Low Input Bias Current PIN CONFIGURATIONS 14-Lead Epoxy DIP (P Suffix) OUT A 1 14 OUT D –IN A 2 13 –IN D +IN A 3 12 +IN D V+ 4 11 V– +IN B 5 10 +IN C 6 9 –IN C –IN B OUT B 7 8 OUT C GENERAL DESCRIPTION The OP11 provides four matched 741-type operational amplifiers in a single 14-lead DIP package. The OP11 is pin compatible with the LM148, LM348, RM4156, RM4158, and HA4741 amplifiers. The amplifier is matched for common-mode rejection ratio and offset voltage which is very important in designing instrumentation amplifiers. In addition, the amplifier is designed to have equal positive-going and negative-going slew rates. This is an important consideration for good audio system performance. 14-Lead Hermetic DIP (Y Suffix) The OP11 is ideal for use in designs requiring minimum space and cost while maintaining performance. OUT A 1 14 OUT D –IN A 2 13 –IN D +IN A 3 12 +IN D V+ 4 11 V– +IN B 5 10 +IN C 6 9 –IN C –IN B OUT B 7 8 OUT C V+ –IN +IN OUTPUT V– Figure 1. Simplified Schematic REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2002 OP11–SPECIFICATIONS ELECTRICAL CHARACTERISTICS (@ V = 15 V, T = 25C, unless otherwise noted) S A Parameter Symbol Conditions OP11A/OP11E Min Typ Max Input Offset Voltage VOS RS = 10 kW 0.3 0.5 0.6 2.5 Input Offset Current IOS 5.5 20 25 Input Bias Current IB 180 300 300 Input Resistance Differential Mode1 RIN 0.17 0.29 0.1 0.17 0.1 0.17 MW Input Voltage Range IVR ± 12 ± 13 ± 12 ± 13 ± 12 ± 13 V Common-Mode Rejection Ratio CMRR 100 120 100 120 70 100 dB VCM = ± 12 V, RS = 10 kW Min OP11F Typ Max Min OP11G Typ Max Unit 1.2 5.0 mV 50 75 200 nA 500 300 500 nA Power Supply Rejection Ratio PSRR VS = ± 5 V to ± 15 V, RS £ 10 kW Output Voltage Swing VO RL = 2 kW ± 11 ± 13 Large-Signal Voltage Gain AVO RL £ 2 kW, VO = ± 10 V 100 650 Power Consumption2 Pd VO = 0 V 105 Input Noise Voltage en p-p 0.1 Hz to 10 Hz 0.7 0.7 0.7 mV p-p Input Noise Voltage Density en fO = 10 Hz fO = 100 Hz fO = 1 MHz 18 14 12 18 14 12 18 14 12 nV/÷Hz nV/÷Hz nV/÷Hz Input Noise Current In p-p 0.1 Hz to 10 Hz 17 17 17 pA p-p Input Noise Current Density In fO = 10 Hz fO = 100 Hz fO = 1 MHz 1.8 1.5 1.2 1.8 1.5 1.2 1.8 1.5 1.2 pA/÷Hz pA/÷Hz pA/÷Hz Channel Separation CS 100 130 100 130 130 dB 2 SR 0.7 1.0 0.7 1.0 0.7 1.0 V/ms VO = 20 V p-p 11 16 11 16 11 16 kHz 2.4 3.0 2.4 3.0 2.4 3.0 MHz Slew Rate Large Signal Bandwidth3 Closed-Loop Bandwidth4 BW AVCL = 1 Rise Time 3 tf AV = 1, VIN = 50 mV Overshoot 3 OS 4 32 4 ± 11 100 180 32 ± 13 ± 11 650 123 10 50 180 100 ± 13 V 500 210 mV/V V/mV 340 mW 110 145 110 145 110 145 ns 15 25 15 25 15 25 % NOTES 1 Guaranteed by input bias current. 2 Total dissipation for all four amplifiers in package. 3 Sample tested. 4 Guaranteed by rise time. Specifications subject to change without notice –2– REV. A OP11 ELECTRICAL CHARACTERISTICS (@ VS = 15 V, 55C £ TA £ 125C for OP11A, 0C £ TA £ 70C for OP11E, unless otherwise noted) Conditions Input Offset Voltage VOS RS £ 10 kW 0.4 1.0 0.4 0.8 mV Average Input Offset Voltage Drift1 TCVOS RS £ 10 kW 2.0 10 2.0 10 mV/∞C Input Offset Current IOS 20 40 14 30 nA Average Input Offset Current Drift TCIOS 0.1 0.3 0.1 0.3 nA/∞C Input Bias Current IB 200 375 200 350 nA Input Voltage Range IVR Common-Mode Rejection Ratio CMRR Power Supply Rejection Ratio Large-Signal Voltage Gain VCM = ± 12 V, RS £ 10 kW AVO Unit ± 12 ± 13 ± 12 ± 13 V 100 120 100 120 dB VS = ± 5 V to ± 15 V, RS £ 10 kW PSRR Min OP11E Typ Max Symbol 1 Min OP11A Typ Max Parameter 4 32 4 32 mV/V RL ≥ 2 kW, VO = ± 10 V 50 250 50 250 V/mV ± 11 ± 13 ± 11 ± 13 V Output Voltage Swing VO RL ≥ 2 kW Power Consumption2 Pd VO = 0 V 115 200 115 200 mW NOTES 1 Guaranteed but not tested. 2 Total dissipation for all four amplifiers in package. Specifications subject to change without notice ELECTRICAL CHARACTERISTICS (@ V = 15 V, 40C £ T £ +85C, R £ 100 , unless otherwise noted) S A S Conditions Input Offset Voltage VOS RS £ 10 kW 0.8 3.0 1.5 Average Input Offset Voltage Drift TCVOS RS £ 10 kW 4.0 15 4.0 Input Offset Current IOS 40 60 250 300 nA Average Input Offset Current Drift1 TCIOS 0.3 0.6 0.3 0.6 nA/∞C Input Bias Current IB 400 550 400 800 nA Input Voltage Range IVR Common-Mode Rejection Ratio CMRR Power Supply Rejection Ratio Large-Signal Voltage Gain Output Voltage Swing 2 Power Consumption PSRR 6 .0 Unit mV mV/∞C ± 12 ± 13 ± 12 ± 13 V 100 120 70 100 dB VS = ± 5 V to ± 15 V, RS £ 10 kW 4 32 10 100 mV/V RL ≥ 2 kW, VO = ± 10 V 50 250 25 100 V/mV VO RL ≥ 2 kW ± 11 ± 13 ± 11 ± 13 V Pd VO = 0 V AVO 115 NOTES 1 Guaranteed but not tested. 2 Total dissipation for all four amplifiers in package. Specifications subject to change without notice REV. A Min OP11G Typ Max Symbol VCM = ± 12 V, RS £ 10 kW Min OP11F Typ Max Parameter –3– 200 250 400 mW OP11 ABSOLUTE MAXIMUM RATINGS* Supply Voltage (VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 22 V Input Voltage* . . . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 30 V Output Short-Circuit Duration . . . . . . . . . . . . . . . Continuous (One Amp Only) Storage Temperature Range Y Package . . . . . . . . . . . . . . . . . . . . . . . . –65∞C to +150∞C P Package . . . . . . . . . . . . . . . . . . . . . . . . . –65∞C to +125∞C Lead Temperature Range (Soldering, 60 sec) . . . . . . . . 300∞C Operating Temperature Range OP11A . . . . . . . . . . . . . . . . . . . . . . . . . . . –55∞C to +125∞C OP11E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0∞C to 70∞C OP11F, OP11G . . . . . . . . . . . . . . . . . . . . . –40∞C to +85∞C Package Type JA* JC Unit 14-Lead Plastic DIP (P) 14-Lead Hermetic DIP (Y) 83 108 39 15 ∞C/W ∞C/W *qJA is specified for worst-case conditions, i.e., qJA is specified for device in socket for CERDIP and P-DIP packages. ORDERING GUIDE *Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. Model Temperature Range Package Description Package Option OP11AY* OP11EP OP11EY* OP11FP* OP11GP –40∞C to +125∞C –40∞C to +125∞C 0∞C to 85∞C –40∞C to 85∞C –40∞C to 85∞C 14-Lead CERDIP 14-Lead Epoxy DIP 14-Lead CERDIP 14-Lead Epoxy DIP 14-Lead Epoxy DIP Y-14 P-14 Y-14 P-14 P-14 *Not for new designs. Obsolete April 2002. For Military processed devices, please refer to the Standard Microcircuit Drawing (SMD) available at www.dscc.dla.mil/programs/milspec/default.asp SMD Part Number ADI Equivalent 5962-89801012A 5962-8980101CA OP11ARCMDA OP11AYMDA MATCHING CHARACTERISTICS (@ V = 15 V, T = 25C, R £ 100 , unless otherwise noted) S Parameter Symbol Input Offset Voltage Match DVOS Common-Mode Rejection Ratio Match DCMRR A S Conditions VCM = ± 12 V VCM = ± 12 V OP11A, OP11E Min Typ Max 94 0.5 0.75 1 120 20 Min 94 OP11F Typ Max Unit 0.6 2.0 mV 1 120 20 mV/V dB Specifications subject to change without notice (@ VS = 15 V, 55C £ TA £ +125C for OP11A, 0C £ TA £ 70C for OP11E, 40C £ TA £ MATCHING CHARACTERISTICS +85C for OP11F, R £ 100 , unless otherwise noted) S Parameter Symbol Input Offset Voltage Match DVOS Common-Mode Rejection Ratio Match DCMRR Conditions VCM = ± 12 V VCM = ± 12 V OP11A, OP11E Min Typ Max 94 0.6 1.0 3.2 110 20 Min 94 OP11F Typ Max Unit 1.0 2.5 mV 3.2 110 20 mV/V dB Specifications subject to change without notice CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the OP11 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –4– WARNING! ESD SENSITIVE DEVICE REV. A Typical Performance Characteristics– OP11 0.1 800 VS = 15V RL = 2k 700 0.2 600 OPEN-LOOP GAIN – V/mV OFFSET VOLTAGE – mV VS = 15V 0.3 0.4 500 400 300 200 100 0.5 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 0 60 140 TPC 1. Input Offset Voltage vs. Temperature 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 VS = 15V RL = 2k TA = 25C CL = 100pF OPEN-LOOP GAIN – dB INPUT OFFSET CURRENT – nA 100 15 10 GAIN 0 45 80 90 60 PHASE 40 135 20 180 PHASE LAG – Degrees VS = 15V 5 0 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 0 0.1 140 1.0 10 100 1k 10k FREQUENCY – Hz 100k 1M 10M TPC 5. Open-Loop Gain and Phase vs. Frequency TPC 2. Offset Current vs. Temperature 1.4 300 NORMALIZED VALUE REFERRED TO 25C VS = 15V INPUT BIAS CURRENT – nA 140 TPC 4. Open-Loop Gain vs. Temperature 20 200 100 0 60 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 VS = 15V 1.3 1.2 1.1 SLEW RATE 1.0 0.9 0.8 BANDWIDTH 0.7 0.6 60 140 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 TPC 6. Normalized Slew Rate and Bandwidth vs. Temperature TPC 3. Bias Current vs. Temperature REV. A 120 –5– OP11 140 800 RL = 2k TA = 25C 120 CHANNEL SEPARATION – dB OPEN-LOOP GAIN – V/mV 700 600 500 400 300 200 0 5 60 40 VOLTAGE NOISE DENSITY – nV/ Hz 100 80 60 40 20 10 100 1k FREQUENCY – Hz 10k 10k 100k VS = 15V TA = 25C 100 10 1 10 100k TPC 8. CMRR vs. Frequency 100 1k FREQUENCY – Hz 10k TPC 11. Voltage Noise Density vs. Frequency 140 100 CURRENT NOISE DENSITY – pA/ Hz VS = 15V TA = 25C 120 100 80 60 40 20 0 1.0 1k FREQUENCY – Hz 1k VS = 15V TA = 25C 120 0 1.0 100 TPC 10. Channel Separation vs. Frequency 140 CMRR – dB 80 0 10 20 10 15 POWER SUPPLY VOLTAGE – V TPC 7. Open-Loop Gain vs. Supply Voltage PSRR – dB 100 20 100 0 VS = 15V TA = 25C 10 100 1k FREQUENCY – Hz 10k VS = 15V TA = 25C 10 1 0.1 10 100k TPC 9. PSRR vs. Frequency 100 1k FREQUENCY – Hz 10k TPC 12. Noise Current Density vs. Frequency –6– REV. A OP11 20 VS = 15V TA = 25C 14 OUTPUT VOLTAGE SWING – V OUTPUT VOLTAGE – mV 16 VS = 15V RL = 2k TA = 25C CL = 100pF 0 20 POSITIVE SWING NEGATIVE SWING 12 10 8 6 4 2 200 0 400 TIME – ns 600 0 0.1 800 TPC 13. Transient Response 1 LOAD RESISTANCE TO GROUND – k 10 TPC 16. Output Voltage vs. Load Resistance 5 VS = 15V RL = 2k TA = 25C CL = 100pF OUTPUT VOLTAGE – V 2 TA = 25C QUIESCENT CURRENT – mA 3 1 0 1 2 4 3 2 1 3 0 2 4 6 8 10 12 TIME – s 14 16 18 0 20 TPC 14. Voltage Follower Pulse Response 40 20 30 TOTAL SUPPLY VOLTAGE – V TPC 17. Quiescent Current vs. Supply Voltage VS = 15V RL = 2k TA = 25C 24 VS = 15V POWER CONSUMPTION – mW OUTPUT VOLTAGE PEAK-TO-PEAK – V 10 140 28 (27) 20 16 12 8 130 120 110 4 0 1k 10k 100k FREQUENCY – Hz 100 60 1M TPC 15. Maximum Output Swing vs. Frequency REV. A 0 40 20 0 20 40 60 80 TEMPERATURE – C 100 120 140 TPC 18. Power Consumption vs. Temperature –7– OUTLINE DIMENSIONS Dimensions shown in inches and (mm). C02784-0-4/02(A) 14-Lead Epoxy DIP (P Suffix) 0.795 (20.19) 0.725 (18.42) 14 8 0.280 (7.11) 0.240 (6.10) 7 1 PIN 1 0.100 (2.54) BSC 0.060 (1.52) 0.015 (0.38) 0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) 0.210 (5.33) MAX 0.130 (3.30) 0.160 (4.06) MIN 0.115 (2.93) 0.022 (0.558) 0.070 (1.77) SEATING PLANE 0.014 (0.356) 0.045 (1.15) 0.015 (0.381) 0.008 (0.204) 14-Lead Hermetic DIP (Y Suffix) 0.005 (0.13) MIN 0.098 (2.49) MAX 14 8 PIN 1 1 7 0.100 (2.54) BSC 0.785 (19.94) MAX 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.310 (7.87) 0.220 (5.59) 0.320 (8.13) 0.290 (7.37) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN SEATING 0.070 (1.78) PLANE 0.030 (0.76) 15 0 0.015 (0.38) 0.008 (0.20) Revision History Location Page Data Sheet changed from REV. 0 to REV. A. Change OP-09/OP-11 to OP11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global Edits to Figure 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits to SPEC TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Deletion of DICE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Deletion of WAFER TEST LIMITS Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Deletion of TYPICAL ELECTRICAL CHARACTERISTICS Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 –8– PRINTED IN U.S.A. Edits to PIN CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1