KBL6005 thru KBL610 6.0 A Single-Phase GPP Bridge Rectifier Rectifier Reverse Voltage 50 to 1000V 19.0 + 0.5 Features 14.2 + 0.5 15.7 + 0.5 0 1.3 + 0.1 19.0 MIN. This series is UL listed under the Recognized Component Index, file number E142814 Ideal for printed circuit board mounting The plastic material used carries Underwriters Laboratory flammability recognition 94V-0 Built-in printed circuit board stand-offs High case dielectric strength High temperature soldering guaranteed 265 /10 seconds at 5 lbs (2.3kg) tension 4.1 + 0.5 5.1 + 0.5 Mechanical Data Case: Reliable low cost construction utilizing molded plastic technique Terminals: Plated leads solderable per MIL-STD-202, Method 208 Mounting Position: Any Weight: 0.2 ounce, 5.6 grams (approx) 6.25 + 0.25 2.1 + 0.2 Dimensions in millimeters(1mm =0.0394") Maximum Ratings & Thermal Characteristics Rating at 25 C ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz. For Capacitive load derate current by 20%. KBL KBL KBL KBL KBL KBL Parameter Symbol 6005 601 602 604 606 608 VRRM 200 400 800 Maximum repetitive peak reverse voltage 50 100 600 Maximum RMS bridge input voltage Maximum DC blocking voltage Maximum average forward rectified output current at TA=50 C VRMS VDC 35 50 70 140 280 100 200 400 KBL 610 unit 1000 V 420 560 700 V 600 800 1000 V IF(AV) 6.0 A Peak forward surge current single sine-wave IFSM superimposed on rated load (JEDEC Method) 200 A I t 2 166 A sec ReJA TJ, TSTG 10.0 Rating for fusing ( t<8.3ms) Typical thermal resistance per element (1) Operating junction and storage temperature range 2 C/W -55 to + 150 Electrical Characteristics Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz. For Capacitive load derate by 20 %. KBL KBL KBL KBL KBL Parameter Symbol 6005 601 602 604 606 Maximum instantaneous forward voltage drop VF 1.1 per leg at 6.0A Maximum DC reverse current at rated TA =25 C DC blocking voltage per element TA =125 C IR Notes: (1)Thermal resistance from Junction to Ambemt on P.C.board mounting. www.asemi.tw 10 1000 KBL 608 KBL Unit 610 V A o Rating and Characteristic Curves ( TA=25 C Unless otherwise noted ) KBL6005 thru KBL610 Fig. 2 Maximum Non-repetitive Peak Forward Surge Current Fig. 1 Derating Curve for Output Rectified Current Peak Forward Surge Current, Amperes Average Forward Output Current, Amperes 6.0 4.0 2.0 60Hz Resistive of Inductive Load 200 8.3ms Single half-sine-Wave [JEDEC Method] 175 150 125 100 75 50 40 10 1 100 Number of Cycles at 60HZ 0 0 50 100 150 o Case Temperature, C Fig. 4 Typical Reverse Characteristics 10 Instantaneous Reverse Current ,Amperes Fig. 3 Typical Instantaneous Forward Characteristics 40 20 10 Tc=100 C 1.0 0.1 TA=25 C 4.0 .01 1.0 0 20 40 60 80 100 120 140 Percent of Rated Peak Reverse Voltage, % 0.1 Tj=25 C Pulse Width=300us 2% duty cycle .01 0.6 0.7 0.8 0.9 1.0 1.1 Instantaneous Forward Voltage, Volts Fig. 5 Typical Junction Capacitance 1.2 250 1.3 Tj=25 C f=1.0MHz Ving =50mV p.p. 200 Capacitance, pF Instantaneous Forward Current, Amperes 100 150 100 50 1 1.5 2 10 Reverse Voltage, Volts www.asemi.tw 100