ASEMI W005M

W005 thru W10
1.5 A Single-Phase Silicon Bridge Rectifier
Rectifier Reverse Voltage 50 to 1000V
8.1 + 0.5
5.35 + 0.25
Features
This series is UL listed under the Recognized
Component Index, file number E142814
30.5 MIN
32.3 MIN
The plastic material used carries Underwriters Laboratory
flammability recognition 94V-0
Ideal for printed circuit board mounting
High surge current capability
High temperature soldering guaranteed 265 C/10
seconds at 5 lbs (2.3kg) tension
5.1 + 0.5
Mechanical Data
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Plated leads solderable per MIL-STD-202,
Method 208
Mounting Position: Any
Weight: 0.05 ounce, 1.3 grams (approx)
5.1 + 0.5
Dimensions in millimeters(1mm =0.0394")
Maximum Ratings & Thermal Characteristics
Rating at 25 C ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz.
For Capacitive load derate current by 20%.
Parameter
Symbol W005M W01M W02M W04M W06M W08M W10M unit
Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000
V
Maximum RMS bridge input voltage
VRMS
35
70
140
280
420
560
700
V
VDC
50
100
200
400
600
800
1000
V
Maximum DC blocking voltage
Maximum average forward rectified
output current at TA=25 C
IF(AV)
1.5
A
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
IFSM
50
A
I t
2
10.0
A sec
ReJA
50.0
C/W
24.0
pF
Rating for fusing ( t<8.3ms)
Typical thermal resistance per element (1)
Typical junction capacitance per element (2)
Operating junction and storage temperature
range
Cj
TJ,
TSTG
2
-55 to + 150
Electrical Characteristics
Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz.
For Capacitive load derate by 20 %.
Parameter
Symbol W005M W01M W02M W04M W06M W08M W10M Unit
Maximum instantaneous forward voltage drop
per leg at 1.5A
VF
1.1
Maximum DC reverse current at rated TA =25 C
DC blocking voltage per element
TA =100 C
IR
10
1000
Notes: (1)Thermal resistance from Junction to Ambemt on P.C.board mounting.
(2)Measured at 2.0MHz and applied reverse voltage of 4.0 volts.
www.asemi.tw
V
A
o
Rating and Characteristic Curves ( TA=25 C Unless otherwise noted )
W005M thru W10M
Fig. 2 Maximum Non-repetitive Peak
Forward Surge Current
Peak Forward Surge Current,
Amperes
Fig. 1 Derating Curve for
Output Rectified Current
1.5
Average Forward Output
Current, Amperes
60Hz Resistive of
Inductive Load
1.0
0.5
60
8.3ms
Single half-sine-Wave
[JEDEC Method]
50
40
30
20
10
0
10
1
100
Number of Cycles at 60HZ
Fig. 4 Typical Reverse
Characteristics
0
60
40
80
100
120
140
100
o
Case Temperature, C
Tj=125 C
Instantaneous Reverse
Current ,Amperes
10
10
Tj=25 C
0.1
.01
0
20
40
60
80
100
120
Percent of Rated Peak Reverse
Voltage, %
1.0
Fig. 5 Typical Junction Capacitance
100
Tj=25 C
f=1.0MHz
0.1
Tj=25 C
Pulse Width=300us
.01
0.4
0.6
0.8
1.0
1.2
Instantaneous Forward
Voltage, Volts
1.4
1.6
Capacitance, pF
Instantaneous Forward Current,
Amperes
Fig. 3 Typical Instantaneous
Forward Characteristics
1.0
10
1
1.5
2
10
Reverse Voltage, Volts
www.asemi.tw
100
140