Tentative July 22, 2004 No. 3284LTD-1468-5 LIQUID CRYSTAL DISPLAY MODULE TECHNICAL DATA TX06D15VM1EAA (NOTE) 1. This document may, w holly or partially, be subject to change w ithout notice. 2. All rights are reserved ; No one is permitted to reproduce or duplicate, in any from, the w hole or part of this document w ithout Hitachi's permission. 3. No one is permitted to explain contents of this document to third parties w ithout Hitachi's permission. 4. Hitachi w ill not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user's unit according to this document, any previous reports or oral discussions. 5. Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Hitachi's products. Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein. 6. No license is granted by implication or otherw ise under any patents or other rights of any third party or Hitachi, Ltd. 7. LIFE SUPPORT APPLICATIONS : Hitachi's products are not authorized for use in LIFE SUPPORT SYSTEMS. 3. GENERAL DATA (1) Part Name TX06D15VM1EAA (2) Module Dimensions 41.85(W) mm x 56.0(H) mm x 4.6(t) mm (3) Active Area Dimensions 34.848(W) mm x 43.56(H) mm (4) Pixel Pitch 0.198(W) mm x 0.198(H) mm (5) Resolution 176 x 3 (R,G,B)(W) x 220 (H) dots (6) Color Pixel Arrangement RGB Vertical Stripe (7) Display Mode Transflective Type, Normally Black Mode (8) Color Number 65K or 262K Colors (9) View ing Direction 6 O'clock (10) Back Light Light Emitting Diode (LED) (11) Weight 13.8g (typ) (12) Pow er Supply Voltage Vcc=Vci=2.8V (typ) (13) LCD Driver IC Source IC : HD66772 Gate and Pow er IC : HD66774S (14) Interface Clock Synchronized Serial Interface (SPI) + RGB Interface (18bit) 16bit RGB - I/F 18bit RGB - I/F Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 65k colors (Use 16bit of the 18bit bus interface) 262k colors 3284PS 2603-TX06D15VM1EAA-4 Page 3-1/1 4. ABSOLUTE MAXIMUM RATINGS 4. 1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS OF LCD VSS=0V SYMBOL Vcc MIN -0.3 MAX 4.6 UNIT V Pow er Supply for Analog Vci -0.3 4.6 V Note 1 Input Voltage Vi -0.3 Vcc+0.3 V Note 1, 2 Input Current Ii 0 100 mA LED Reverse Voltage VR - 5 V LED Forw ard Current I LED - Note 3 mA - - (+/-2) kV ITEM Pow er Supply for Logic Static Electricity COMMENT Note 1 Note 4 Note 1 Voltage from GND. Note 2 Applies to the RESET, ID, SDO, SDI, SCL, CS*, VLD, VSYNC, HSYNC, DOTCLK ENABLE, and PD17-0 pins. Note 3 Ambient Temperature vs. Allow able Forw ard Current 30 6mA(85 deg C) 20 10 0 0 20 40 60 80 100 Ambient temperature (deg C) Note 4 150pF-1.5Kohm/200pF-0 ohm, 25 deg C-70%RH. The Surface of LCD center are subjected. 4. 2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS ITEM STORAGE OPERATING MIN MAX Ambient Temperature -20 deg C 70 deg C Note 1 MAX -30 deg C 80 deg C Note 1 Note 1 Not Acceptable Not Acceptable Humidity Corrosive Gas MIN COMMENT Note 2 Without condensation Ta<40 deg C : 85%RH max. Ta>40 deg C : Absolute humidity must be low er than the humidity of 85%RH at 40 deg C. Note 2 Hitachi Displays, Ltd. Background color changes slightly depending on ambient temperature. This phenomenon is reversible. Date Mar. 16, 2004 Sh. No. 3284PS 2604-TX06D15VM1EAA-4 Page 4-1/1 5. ELECTRICAL CHARACTERISTICS TFT-LCD Module ITEM Pow er Supply Logic Voltage Analog Ta=25 deg C, VSS=0V SYMBOL Vcc CONDITION - MIN 2.72 TYP 2.8 MAX 2.89 Vci "H" level 2.72 0.7xVcc 2.8 - 2.89 Vcc "L" level -0.3 - 0.15xVcc UNIT NOTE V Input Voltage for Logic Circuits Vi Output Voltage for Logic Circuits Vo "H" level "L" level 0.75xVcc - - 0.15xVcc Input/Output Leak Current I Li - -1 - - 1 - All White Partial - - Sleep - Standby Moving Picture(Full) - (10.3) - Icc + Ici Pow er Supply Current 2000 650 40 3 V 1) V 1) uA 2) uA Frame Frequency f FLM - - 90 - mA Hz LED Forw ard Voltage V LED - - 3.6 - V LED Forw ard Current I LED - - 15.0 (Note 9) mA 3), 5) 4), 5) 6) 7) 8) (Note 1) RESET, ID, SDO, SDI, SCL, CS*, VLD, VSYNC, HSYNC, DOTCLK, ENABLE, PD17-0 Pins: SDO, SDI Pins: RESET, CS*, SCL, VLD, ID VSYNC, HSYNC, DOTCLK ENABLE, PD17-0 Vcc PMOS (Input Circuit) NMOS Vcc (Output Circuit : Three State) Vcc PMOS GND NMOS GND PMOS Output Enable Output Data NMOS GND (Note 2) Excepted the current of out driving MOS. (Note 3) Vcc=Vci=2.8V, Internal clock operation mode & No RGB I/F input signals. (Note 4) Vcc=Vci=2.8V, 8 colors mode, f FLM=45Hz, No RGB I/F input signals. Partial Pattern 16 Line : White (8 color mode) 204 Line : Black (8 color mode) (Note (Note (Note (Note 5) 6) 7) 8) Still picture is internal RAM. Vcc=Vci=2.8V, Sleep mode & No RGB I/F input signals. Vcc=Vci=2.8V, Standby mode & No RGB I/F input signals. Vcc=Vci=2.8V, 18bit- RGB I/F & High speed write mode. (fFLM=90Hz, Black & White Checker) All data written via the RGB-I/F are written to the internal RAM. (Note 9) Refer to the 4. 1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS OF LCD.(Page 4-1/1) Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2605-TX06D15VM1EAA-4 Page 5-1/1 6. OPTICAL CHARACTERISTICS 6.1 OPTICAL CHARACTERISTICS OF LCD (BACKLIGHT ON) Ta=25 deg C SYMBOL CONDITION Brightness B f =0 deg, q=0 deg Uniformity - ITEM TYP MAX UNIT NOTE 50 60 - cd/m2 1) f =0 deg, q=0 deg - - +/-30 % 3),5) q=0 deg, K>2.0 - 60 - - 60 - deg q=90 deg, K>2.0 4),6),7) K f =0 deg, q=0 deg 30 40 - - 6) tr+tf Ta=25 f =0 deg deg C q=0 deg Ta=0 deg C - 35 70 ms 8) - 140 280 x 0.47 0.52 0.57 y 0.28 0.33 0.38 x 0.27 0.32 0.37 0.44 0.49 0.54 - 0.10 0.15 0.20 9) y 0.09 0.14 0.19 x 0.24 0.29 0.34 y 0.26 0.31 0.36 f2-f1 View ing angle Contrast ratio Response time (rise+fall) Red Green Color tone (Primary Color) Blue White y x f =0 deg q=0 deg MIN (Measurement condition : Hitachi standard) Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2606-TX06D15VM1EAA-4 Page 6-1/3 6.2 OPTICAL CHARACTERISTICS OF LCD (BACKLIGHT OFF) Ta=25 deg C ITEM Reflectance CONDITION MIN TYP MAX UNIT NOTE R f =0 deg, q=0 deg 15 20 - % 2) q=0 deg, K>2.0 - 60 - - 60 - deg 4),6) q=90 deg, K>2.0 K f =0 deg, q=0 deg 5 15 - - 6) tr+tf Ta=25 f =0 deg deg C q=0 deg Ta=0 deg C - 25 50 - 100 200 ms 8) x 0.44 0.49 0.54 y 0.29 0.34 0.39 x 0.30 0.35 0.40 0.39 0.44 0.49 - 0.15 0.20 0.25 9),10) 0.12 0.17 0.22 x 0.33 0.38 0.43 y 0.31 0.36 0.41 f2-f1 View ing angle Contrast ratio Response time (rise+fall) Color tone (Primary Color) SYMBOL Red Green y x Blue y White f =0 deg q=0 deg (B/L:turned off) (Measurement condition : Hitachi standard) Note 1. Definition of Brightness "B" LCM Sensor Sensor : TOPCON/BM-5A or same level equipment 500mm Measuring point : Active area center Note 2. Definition of Reflectance "R" Circular and Flat Light source Circular hole R= LCM or SWB Sensor BLCM x 100(%) BSWB BLCM : Brightness of LCM at optimum voltage. (displaying w hite pattern) BSWB : Brightness of SWB. SWB : Standard w hite board. 500mm Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2606-TX06D15VM1EAA-4 Page 6-2/3 Note 3. Measuring point (1) 44 Note 4. Definition of q and f (Normal) View ing direction 88 132 (176) (Pixel) (1) P1 P2 P3 P4 P5 P6 P7 P8 P9 Z f1 55 f2 y (q=180deg) 110 X 165 X' q (220) y' (q=0deg) Note 5. Definition of the brightness uniformity (Max brightness or Min brightness) - (Average brightness) (Average brightness) Note 6. Definition of Contrast "K" Brightness w hen displaying White raster Brightness w hen displaying Black raster K= Note 7. Definition of view ing angle f1 and f2 f=0 deg f1<0 deg<f2 f 2.0 Sensor f1 f2 View ing angle f Sensor : BM-5 or similar equipment Note 8. Definition of optical response time Display data Black Black White Black T ime % 100 90 10 0 tr :Rise time tf :Fall time Note 9. The LCD driving voltage should be adjusted so as to obtain maximum contrast. Note 10. The color temperature of light source is 5200K. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2606-TX06D15VM1EAA-4 Page 6-3/3 7. BLOCK DIAGRAM G1 X1,Y 1 TFT-LCD 176(H) x RGB x 220(V) G220 HD66774S X1,Y220 Vcom CL1, FLM, DISPTM, M, EQ DCCLK, GCS*, GDA, GCL X176,Y220 Vcom 9 HD66772 CL1, FLM, DISPTM, M, EQ DCCLK, GCS*, GDA, GCL VDH DDVDH VREG1OUT DDVDH RESET RESET Vci Vcc GND RESET PD17-PD0 ID, SCL, VLD SDO, SDI, CS* DOTCLK, VSYNC ENABLE, HSYNC 18 6 4 AN Note 1 R1 R2 R3 LED CA1 LED CA2 LED CA3 R1-3: 100 ohm Note 1 Connect the resistor for overcurrent protection betw een CA(Cathode) and GND. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2607-TX06D15VM1EAA-4 Page 7-1/1 8. INTERFACE 8. 1 INTERNAL PIN CONNECTION PIN No. 1 2 3 4 5 6 7 8 SIGNAL AN CA1 CA2 CA3 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Hitachi Displays, Ltd. ID NC FUNCTION Power Supply for LED GND for LED1 GND for LED2 GND for LED3 Reset ID NC NC NC NC NC NC NC NC NC NC NC RESET NC SDO SDI SCL NC CS* VLD VSYNC HSYNC DOTCLK ENABLE PD17 PD16 PD15 PD14 PD13 PD12 PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 Vci Vcc GND AGND Date NC Serial Instruction Data Out Serial Instruction Data In Synchronous Clock Signal NC Chip Select Active Data signal for write operation Vertical synchronous for Display Data Horizontal synchronous for Display Data Clock signal for Display Data Enable signal for Display Data Display Data(R5) Display Data(R4) Display Data(R3) Display Data(R2) Display Data(R1) Display Data(R0) Display Data(G5) Display Data(G4) Display Data(G3) Display Data(G2) Display Data(G1) Display Data(G0) Display Data(B5) Display Data(B4) Display Data(B3) Display Data(B2) Display Data(B1) Display Data(B0) Power Supply for Analog Power Supply for Logic GND GND for Analog Mar. 16, 2004 Sh. No. I/F: Suitable Connector JAE:FF0245SA1 (JAE:FF0245SS1) 3284PS 2608-TX06D15VM1EAA-4 Page 8-1/9 8.2 RGB INTERFACE MODE SETTING RGB INTERFACE MODE & UNUSED PIN CONNECTION RGB Interface Mode Colors Used Pins RGB Data Bus Unused Pins Pin No. Signal 29 PD12 41 PD0 16-bit 65k PD17-13, PD11-1 PD12, PD0 18-bit 262k PD17-0 GND GND When the 16-bit RGB-I/F is selected, PD12 and PD0 pins must be fixed to the GND level. INPUT DATA & GRAM WRITE DATA 18-bit RGB INTERFACE Data Bus (Input data) PD PD PD PD PD PD PD PD PD PD PD PD PD PD PD PD PD PD 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GRAM write data R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 16-bit RGB INTERFACE Data Bus (Input data) PD PD PD PD PD 17 16 15 14 13 PD PD PD PD PD PD PD PD PD PD PD 11 10 9 8 7 6 5 4 3 2 1 GRAM write data R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 In 16-bit RGB-I/F, the input data are expanded into 18-bit by adding one bit (the same data as the MSB of RB) to the LSB of RB data within HD66772. NUMBER OF COLOR RGB-I/F MODE Hitachi Displays, Ltd. NUMBER OF GRAYSCALE NUMBER OF COLOR R G B 18-bit 64 64 64 262,144 16-bit 32 64 32 65,536 Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-2/9 8.3 GRAM ADDRESS MAP SS=1,GS=0 X 1 2 3 4 173 174 175 176 Y 1 G1 "0000"H "0001"H "0002"H "0003"H "00AC"H "00AD"H "00AE"H "00AF"H 2 G2 "0100"H "0101"H "0102"H "0103"H "01AC"H "01AD"H "01AE"H "01AF"H 3 G3 "0200"H "0201"H "0202"H "0203"H "02AC"H "02AD"H "02AE"H "02AF"H 4 G4 "0300"H "0301"H "0302"H "0303"H "03AC"H "03AD"H "03AE"H "03AF"H 5 G5 "0400"H "0401"H "0402"H "0403"H "04AC"H "04AD"H "04AE"H "04AF"H 6 G6 "0500"H "0501"H "0502"H "0503"H "05AC"H "05AD"H "05AE"H "05AF"H 215 G215 "D600"H "D601"H "D602"H "D603"H "D6AC"H "D6AD"H "D6AE"H "D6AF"H 216 G216 "D700"H "D701"H "D702"H "D703"H "D7AC"H "D7AD"H "D7AE"H "D7AF"H 217 G217 "D800"H "D801"H "D802"H "D803"H "D8AC"H "D8AD"H "D8AE"H "D8AF"H 218 G218 "D900"H "D901"H "D902"H "D903"H "D9AC"H "D9AD"H "D9AE"H "D9AF"H 219 G219 "DA00"H "DA01"H "DA02"H "DA03"H "DAAC"H "DAAD"H "DAAE"H "DAAF"H 220 G220 "DB00"H "DB01"H "DB02"H "DB03"H "DBAC"H "DBAD"H Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. "DBAE"H "DBAF"H 3284PS 2608-TX06D15VM1EAA-4 Page 8-3/9 8.4 INTERFACE TIMING Clock synchronized Serial Interface Timing Characteristics Item Min Typ Max 0.1 - 20 0.35 - 20 40 - - 150 - - 40 - - 150 - - ns - - 20 tCSU ns 20 - - tCH ns 60 - - tSISU ns 30 - - Serial input data hold time tSIH ns 30 - - Serial output data delay time tSOD ns - - 130 Serial output data hold time tSOH ns 5 - - Serial clock cycle time Write Symbol Unit tSCYC us tSCH ns tSCL ns tscr, tscf Read Serial clock "High" level pulse w idth Write Serial clock "Low " level pulse w idth Write Read Read Serial clock rise / fall time Chip select set up time Chip select hold time Serial input data set up time RGB Interface Timing Characteristics Item <<18/16bit RGB Interface Mode(HWM=1)>> Symbol Unit Min Typ Max tSYNCS clock 0 - 1 ENABLE set up time tENS ns 10 - - ENABLE hold time tENH ns 20 - - VLD set up time tVLS ns 10 - - VLD hold time tVLH ns 40 - - DOTCLK "Low " level pulse w idth ns 40 - - DOTCLK "High" level pulse w idth PWDL PWDH ns 40 - - DOTCLK cycle time tCYCD ns 100 - - Data set up time tPDS ns 10 - - Data hold time tPDH ns 40 - - trgbr,trgbf ns - - 25 Symbol Unit Min Typ Max Reset "low " level w idth tRES ms 1 - - Reset rise time trRES us - - 10 VSYNC/HSYNC set up time DOTCLK,VSYNC,HSYNC rise/fall time Reset Timing Characteristics Item Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-4/9 Start : S CS* End : P VIH VIL VIL tSCY C tCSU tSCH tscf tSCL tscr VIH SCL tCH VIH VIH VIL VIL VIL tSISU VIH SDI VIL VIH VIL tSIH Input Data VIH Input Data VIL tSOD tSOH VOH1 SDO Output Data VOL1 Output Data VOH1 VOL1 Clock Synchronized Serial Interface Timing VSYNC HSYNC trgbf trgbr tSYNCS VIH VIH VIL VIL tENH tENS ENABLE VIH VIH VIH VIH VIL VIL VIL VIL tVLS VLD tVLH VIH VIH VIH VIH VIL VIL VIL VIL trgbf trgbf PW DL VIH VIH VIH DOTCLK PW DH VIL VIL VIL tCYCD tPDS PD17-0 VIH VIH VIL VIL tPDH Wright Data VIH VIH VIL VIL RGB Interface Timing tRES RESET* trRES VIH VIL VIL Reset Timing Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-5/9 16-/18-bit RGB Interface Timing 1 frame BPP V= 8H FPPV = 8H DP=220H VLW=4H VSYNC 1H HSYNC 1H HLW=4CLK HSYNC 1CLK DOTCLK BPP H=8CLK FPPH=4CLK ENABLE VLD PD17-0 Valid Data (176) FPP : Front porch period BPP : Back porch period DP : Display operation period VLW : The period in which VSYNC is low level HLW : The period in which HSYNC is low level Item HLW BPPH FPPH VLW BPPV FPPV DP The number of raster-row s of 1frame min 1DOTCLK typ 4DOTCLK max - Note HLW > 1DOTCLK HLW (1DOTCLK) - - BPPH > HLW 1H 2H 2H - 2HLW (8DOTCLK) 4DOTCLK 4H 8H 8H 220H - VLW > 1H 14H 14H 240H - - - BPPV + FPPV = 16H BPPV + DP + FPPV f DOTCLK = f FLM x (220 + BPPV + FPPV) x (176 + BPPH + FPPH) Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-6/9 8.5 REGISTER SETTING FLOW < Pow er ON sequence > Pow er supply setting(1) Pow er supply setting(2) Pow er supply setting(3) Mode Setting Index R11h R12h R13h R14h R0Ah R0Ah R0Ah Value 0x1010 0x0000 0x0609 0x2D0F 0x0100 0x0101 0x0102 R10h 0x0808 R0Ah 0x0100 Wait 20ms or more R13h 0x0619 R0Ah 0x0101 Wait 20ms or more R01h R02h R03h R04h R05h R08h R0Bh R23h R24h R40h R41h R42h R43h R44h R45h R30h R31h R32h R33h R34h R35h R36h R37h R3Fh R0Ah R0Ah 0x011B 0x0500 0x1230 0x0000 0x0000 0x0808 0x0000 0x0000 0x0000 0x0000 0x0000 0xDB00 0xEFEF 0xAF00 0xDB00 0x0100 0x0707 0x0102 0x0204 0x0506 0x0000 0x0706 0x0402 0x0003 0x0106 0x0107 Internal clock operation Mode Operation Mode RGB I/F Mode Serial Transfer Serial Transfer (Note 2) More than 100mS To : Display On sequence Serial Transfer R0Ch R21h R22h R0Ch R21h R22h (Note 1) 0x0000 ----- Graphic RAM w riting (RGB I/F) Graphic RAM w riting (SPI) < Display On sequence > Hight-speed Write Mode R07h 0x0001 Wait 2 frames or more R07h 0x0021 R0Ah 0x0100 R07h 0x0023 Wait 2 frames or more R07h 0x0033 < Display Off sequence > R0Ch 0x0000 R07h 0x0032 Wait 2 frames or more R07h 0x0022 Wait 2 frames or more R07h 0x0000 R0Ah 0x0100 R10h 0x0000 R0Ah 0x0100 Serial Transfer 0x0000 0x0000 ----- Note 1 RGB I/F Mode 16bit 18bit Serial Transfer Internal clock operation Mode Serial Transfer Serial Transfer Value 0x0111 0x0110 Note 2 Operation amplifier stabilizing period Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-7/9 < Standby & Sleep Sequence > (Standby) Display Off sequence Standby Setting(STB="1") (Sleep) Display Off sequence Standby Setting Sleep Setting(SLP="1") Sleep Setting Serial Transfer Oscillation Start Wait 10ms Standby Canceled Sleep Canceled(SLP="0") Standby Canceled(STB="0") Serial Transfer Power ON sequence Power ON sequence Display On sequence Display On sequence Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Sleep Canceled Page 8-8/9 < 8 Colors Mode Setting > (Normal Mode 8 Colors Mode) (8 Colors Mode Normal Mode) Display Off GON="1" , DTE="1" , D1-0="10" Display Off GON="1" , DTE="1" , D1-0="10" Wait 2 frame or more Wait 2 frame or more Display Off GON="1" , DTE="0" , D1-0="10" Display Off GON="1" , DTE="0" , D1-0="10" Wait 2 frame or more Wait 2 frame or more Display Off GON="0" , DTE="0" , D1-0="00" Display Off GON="0" , DTE="0" , D1-0="00" Serial Transfer Serial Transfer RAM Setting RAM Setting CL="1" CL="0" Wait 40ms or more Wait 40ms or more Display On GON="0" , DTE="0" , D1-0="01" Display On GON="0" , DTE="0" , D1-0="01" Wait 2 frame or more Wait 2 frame or more Display On GON="1" , DTE="0" , D1-0="01" Display On GON="1" , DTE="0" , D1-0="01" Serial Transfer Serial Transfer Display On GON="1" , DTE="0" , D1-0="11" Display On GON="1" , DTE="0" , D1-0="11" Wait 2H Period or more Wait 2H Period or more Display On GON="1" , DTE="1" , D1-0="11" Display On GON="1" , DTE="1" , D1-0="11" 8 colors Mode Normal Mode Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2608-TX06D15VM1EAA-4 Page 8-9/9 10. VISUAL INSPECTION 10.1 INSPECTION CONDITION 1) Ambient illumination : 1000 - 1500 [lx] 2) Distance betw een eyes of an inspector and the LCD Module : Approximately 20 [cm] 3) View ing angle : < 30deg eye eye 30deg 30deg LCD Mold 10.2 DEFINITION OF ZONE The visual inspection zone of a LCD Module is divided into three. A zone : The inside of the Active Area. B zone : The outer periphery of the Active Area. C zone : Whole of the LCD Module except the zone A and B. (Including FPC & Plastic Mold) 1.3mm 1.3mm Active Area View ing Area Whole of the LCD Module except the zone A and B A zone B zone C zone Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2610-TX06D15VM1EAA-4 Page 10-1/3 10.3 COSMETIC SPECIFICATION No. 1 Dot defect Sparkle Mode Black Mode 2 3 Applied Inspection Maximum Remarks Unit Zone Mode Acceptable number pcs A 0 ITEM 1 dot Adjacent dots 0 unit A 1 dot 2 pcs A Adjacent dots 0 unit A 2 None pcs A The Total number Line defects Uneven Brightness: Line shape 4 Uneven Brightness: Dot shape Stain Inclusion W < 0.01 L:Ignored : Line shape [mm] 0.01 < W L < 2.0 5 < 0.05 Width, L > 2.0 Length 0.05 < W Stain Inclusion D < 0.1 : dot shape [mm] 0.1 < D < 0.2 6 Diverge diameter 0.2 < D 7 Uneven Anti Reflection 8 Scratch, Dent of Plastic Mold 9 Scratch of FPC Light-On 1),2),4) A Light-On A Light-On 6) A,B Light-On Light-Off 5),6),7) A,B Light-On Light-Off 5),6),7) By Limited sample A,B Light-Off 6) Serious one is not allowed C Light-Off 6) By Limited sample C Light-Off 6) Serious one is not allowed Ignored 2 0 see Dot shape pcs Ignore 2 pcs 0 Note: 1) Defect whose area per each dot is over 50 % is regarded as Dot defect. 2) Defect whose brightness at all black screen is more than 30% is regarded as Bright Dot defect. 3) Defect whose brightness at all white screen is less than 70% is regarded as Dark Dot defect. 4) Defect dots which are not adjacent are regarded as single Dot defect each. 5) Defect which can be easily wiped off is disregarded 6) In case any problems would be brought out, both parties should discuss needed items such as limited samples. 7) In case of gray scale pattern, obvious defect is to be rejected. Definition of D Definition of W and L b D= Hitachi Displays, Ltd. Date L a+b 2 Mar. 16, 2004 (mm) Sh. No. 3284PS 2610-TX06D15VM1EAA-4 Page 10-2/3 No. ITEM 10 Glass crack CRITERIA A B C (1) Electrode L L= 1.8 [mm] Y< (1/4)xL Y (2) Generality Y X X < 5.0 [mm] Y< 1.5 [mm] * No crack allow ed to reach seal area. Y < 1, in case of tw o cracks found. (3) Corner Y X X < 1.5 Y< 1.5 * No crack allow ed to reach seal area. Y < 1, in case of tw o cracks found. (4) The crack that has potential to enlarge None Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2610-TX06D15VM1EAA-4 Page 10-3/3 11. PRECAUTION IN DESIGN 11. 1 GENERAL ATTENTION (1) The LCD module is designed as display for mobile phone. When it is used for other purposes, w e do not guarantee these specifications at all about the contents, quality, safety etc.. Moreover, this module is not particularly developed as an object for equipment in connection w ith a human life such as medical apparatus of life support relation. (2) Please do not decompose this LCD module. There is danger such as a burn, electric shock, and an injury. Moreover, w hen module is decomposed, w e do not guarantee these specifications at all about the contents, quality, safety etc.. 11.2 PRECAUTIONS AGAINST ELECTROSTATIC DISCHARGE As this module contains C-MOS LSIs, it is not strong against electrostatic discharge. Make certain that the operator's body is connected to the ground through a list band etc. And don't touch I/F pins directly. 11.3 HANDLING PRECAUTIONS (1) Please do not leave on a humid environment for a long time. In storage, w hen the ambient temperature is over 35 degrees C , please avoid high humidity. The polarizers degradation is easily caused in high temperature and high humidity. Moreover, It is also the cause of bubble and peeling of polarizer. Please store/operate the LCD module w ithin the relative temperature and normal humidity. (2) Since the polarizer on the top tend to be easily scratched, they should be handled w ith full care so as not to get them touched, pushed or rubbed by a piece on glass, tw eezers and anything else w hich are harder than a pencil lead 3H. (3) Maximum pressure to the surface must be less than 1.96Pa . And if the pressure area is less than 1cm2, maximum pressure must be less than 1.96N . (4) As the adhesives used for adhering upper/low er polarizers w hich w ill be deteriorated by a chemical reaction w ith such chemicals as acetone, toluene, hexane, ethanol and isopropyl alcohol. Don't let the organic solvent or chemicals adhere to polarizers. (5) Lightly w ipe to clean the dirty surface w ith absorbent cotton or other soft material like chamois, soaked in the recommended chemicals w ithout scrubbing it hardly. Alw ays w ipe the surface horizontally or vertically. Never give a w ipe in a circle. To prevent the display surface from damage and keep the appearance in good state, it is sufficient, in general, to w ipe it w ith absorbent cotton. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2611-TX06D15VM1EAA-4 Page 11-1/3 (6) Immediately w ipe off saliva or w ater drop attached on the display area because it may cause deformation or faded color. (7) Fogy dew deposited on the surface may cause a damage, stain or dirt to the polarizer. When you need to take out the LCD module from some place at low temperature for test, etc. It is required to be w armed them up to be temperature higher than room temperature before taking them out. (8) Touching the display area or I/F pins w ith bare hands or contaminating them are prohibited, because the stain on the display area and poor insulation betw een terminals are often caused by being touched w ith bare hands. (Some cosmetics are detrimental to polarizers.) (9) In general, the glass is fragile so that it, especially on its periphery, tends to be cracked or chipped in handling. Please do not give the LCD module sharp shocks caused by falling etc. (10) The LCD is a product made from glass. It is possible to be damaged by the strong shock. Please be careful and prevent to drop it. (11) It doesn't bend and scratch the I/F part. These are cause of no good contact. Please be careful. 11.4 OPERATION PRECAUTION (1) The spike noise causes the mis-operation of circuits. Recommended condition of spike noise level is as follow s : Vcc=+/-200mV(Over and under shoot voltage) (2) Response time depends on the temperature. (In low er temperature, it becomes longer). And also brightness and color depend on the temperature. (3) Be careful for condensation at sudden temperature change. Condensation make damage to polarizer or electrical contact part. And after fading condensation, smear or spot w ill occur. (4) When fixed patterns are displayed at long times, afterimage is likely to occur. (5) Module has high frequency circuit. If you need to shield the electromagnetic noise, please do in yours. (6) Do not connect or remove the module from main system w ith pow er applied. (7) Strong light exposure causes mis-operation of driver. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2611-TX06D15VM1EAA-4 Page 11-2/3 11.5 STORAGE When storing LCD module as spare parts for a long time, the follow ing precautions are necessary. (1) Store the LCD modules in a dark place ; do not expose them to sunlight or fluorescent light. Keep the temperature between 10 degrees C and 30 degrees C,and the humidity between 55% and 75%. (2) The polarizer surface should not come in contact w ith any other object. It is recommended that they be stored in the container in w hich they w ere shipped. 11.6 SAFETY (1) This liquid crystal display module is using glass. When it damages, please w ear a protection glove to deal it. Moreover, w hen any liquid leaked out of a damaged glass cell comes in contact w ith your hands, please w ash it off w ell w ith soap and w ater. (2) Solder is used for mounting of internal electronic component at print circuit board. Since the Lead(Pb) is contained in solder. When you w ant to discard this LCD module, please follow local ordinances or regulations for disposal. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2611-TX06D15VM1EAA-4 Page 11-3/3 12. DESIGNATION OF LOT MARK 12.1 LOT MARK The lot mark consists of 7 or 10-digit production control number. T X 0 6 D 1 5 V M 1 E A A A 3 2 A * H * (Note 1) Production control Production base Day Month Year Revision Part name Revision Contents of change A Year Figure in lot mark Month Figure in lot mark Month Figure in lot mark 2003 3 Jan. 1 July 7 2004 4 Feb. 2 Aug. 8 2005 5 Mar. 3 Sep. 9 2006 6 Apr. 4 Oct. A May 5 Nov. B June 6 Dec. C Day 1 2 3 4 5 6 7 8 9 Figure in lot mark 1 2 3 4 5 6 7 8 9 Production base Figure in lot mark Made in Japan H 10 11 12 13 14 15 16 17 18 19 Day Figure in lot mark A B C D E F G H J K Made in China S W 20 21 22 23 24 25 26 27 28 29 Day Figure in lot mark L M P N Q R S T U V 30 31 Day Figure in lot mark W X Location of the lot mark : On the back of the LCD Module Printing method of a lot mark : Laser marker or Inkjet printer Note (1) Printing method Hitachi Displays, Ltd. Production control No. Upper 7-digit Lower 3-digit Laser marker Lot No. Serial No. Inkjet printer Lot No. - Date Mar. 16, 2004 Sh. No. 3284PS 2612-TX06D15VM1EAA-4 Page 12-1/1 13. PRECAUTION FOR USE (1) A limit sample should be provided by the both parities on an occasion w hen the both parties agree to its necessity. Judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties. (2) On the follow ing occasions, the handling of the problem should be decided through discussion and agreement betw een responsible persons of the both parties. (1) (2) (3) (4) When a question is arisen in the specifications. When a new problem is arisen w hich is not specified in the specifications. When an inspection specification change or operating condition change by customer is reported to HITACHI, and some problem is arisen in the specification due to the change. When a new problem is arisen at the customer's operating set for sample evaluation (3) Regarding the treatment for maintenance and repairing, both parties w ill discuss it in six month later after latest delivery of this product. The precaution that should be observed w hen handling LCM have been explained above. If any points are unclear or if you have any requests, please contact Hitachi. Hitachi Displays, Ltd. Date Mar. 16, 2004 Sh. No. 3284PS 2613-TX06D15VM1EAA-4 Page 13-1/1