GR 47/GR 48 Technical Description CE The product described in this manual conforms to the Radio Equipment and Telecommunication Terminal Equipment (R&TTE) directive 99/5/EC with requirements covering EMC directive 89/336/EEC and Low Voltage directive 73/23/EEC. The product fulfils the requirements according to 3GPP TS 51.010-1, EN 301489-7 and EN60950. The information contained in this document is the proprietary information of Sony Ericsson Mobile Communications. The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Sony Ericsson Mobile Communications, is strictly prohibited. Further, no portion of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, without the prior written consent of Sony Ericsson Mobile Communications, the copyright holder. Second edition (February 2003) Sony Ericsson Mobile Communications. publishes this manual without making any warranty as to the content contained herein. Further Sony Ericsson Mobile Communications. reserves the right to make modifications, additions and deletions to this manual due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this manual. All rights reserved. © Sony Ericsson Mobile Communications., 2003 Publication number: Printed in UK GR47/GR48 Technical description Contents 1 INTRODUCTION ...........................................................................................................5 1.1 OVERVIEW ...............................................................................................................5 1.2 FEATURES ...............................................................................................................6 1.2.1 Type of Mobile Station ......................................................................................6 1.2.2 SMS ................................................................................................................7 1.2.3 Voice calls .......................................................................................................7 1.2.4 Data ................................................................................................................7 1.2.5 SIM Card .........................................................................................................8 1.2.6 Power consumption ..........................................................................................8 1.2.7 Other features ..................................................................................................8 1.2.8 Development Kit...............................................................................................8 1.3 PRECAUTIONS ..........................................................................................................9 1.4 ABBREVIATIONS ........................................................................................................9 2 MECHANICAL DESCRIPTION .................................................................................... 11 2.1 2.2 3 INTERFACE D ESCRIPTION ......................................................................................... 11 PHYSICAL DIMENSIONS ............................................................................................ 12 SYSTEM CONNECTOR INTERFACE .......................................................................... 13 3.1 OVERVIEW ............................................................................................................. 13 3.2 GENERAL ELECTRICAL AND LOGICAL CHARACTERISTICS ................................................ 16 3.2.1 General Protection Requirements.................................................................... 17 3.3 GROUNDS .............................................................................................................. 18 3.3.1 The Analogue Ground..................................................................................... 18 3.3.2 The Digital Ground (DGND) ............................................................................ 18 3.4 R EGULATED POWER S UPPLY .................................................................................... 19 3.4.1 Power Supply (VCC)....................................................................................... 19 3.4.2 Battery Charging Input (CHG_IN) .................................................................... 19 3.5 ON/OFF AND EXTERNAL POWER S IGNALS .................................................................. 20 3.5.1 Module ON/OFF ............................................................................................. 20 3.5.2 External 2.75 V (VIO)...................................................................................... 21 3.6 ANALOGUE A UDIO ................................................................................................... 22 3.6.1 Audio To Mobile Station (ATMS)...................................................................... 22 3.6.2 Audio From Mobile Station (AFMS).................................................................. 24 3.7 MICROPHONE S IGNALS ............................................................................................ 24 3.8 SPEAKER S IGNALS .................................................................................................. 25 3.9 D IGITAL AUDIO ........................................................................................................ 25 3.10 SERIAL DATA ...................................................................................................... 27 3.10.1 UART 1 (RS232) - RD, TD, RTS, CTS, DTR, DCD, DSR and RI ........................ 29 3.10.2 Serial Data Signals - RD, TD ........................................................................... 29 3.10.3 Control Signals - RTS, CTS, DTR, DCD, RI, DSR............................................. 30 3.10.4 UART 2 - TD2, RD2........................................................................................ 32 3.10.5 UART 3 - TD3, RD3........................................................................................ 32 3.11 SIM CARD RELATED SIGNALS................................................................................. 33 3.11.1 SIM Detection – SIM Presence........................................................................ 34 3.12 SERVICE/PROGRAMMING ...................................................................................... 34 3.13 BUZZER .............................................................................................................. 35 3.14 LED .................................................................................................................. 35 3.15 TX_ON - BURST TRANSMISSION ............................................................................ 36 3.16 R EAL TIME CLOCK ............................................................................................... 36 3.17 EXTENDED IO CAPABILITIES ................................................................................... 37 3.17.1 LED/IO6......................................................................................................... 37 3.17.2 I#/O# ............................................................................................................. 37 GBBA/SEM/BMS 03:0001 Rev A 3 GR47/GR48 Technical description 3.17.3 UART3/IO# .................................................................................................... 37 3.17.4 IO# / ADC# .................................................................................................... 37 3.18 KEYBOARD INTERFACE ......................................................................................... 39 3.18.1 IO# / KEYROW#............................................................................................. 39 3.18.2 KEYCOL#...................................................................................................... 39 4 ANTENNA CONNECTOR............................................................................................ 41 5 AT COMMAND SUMMARY ......................................................................................... 42 6 EMBEDDED APPLICATIONS ...................................................................................... 45 6.1 FEATURES ............................................................................................................. 45 6.2 IMPLEMENTATION .................................................................................................... 45 6.2.1 Limitations ..................................................................................................... 45 6.2.2 IDE (Integrated Developers Environment) ........................................................ 46 7 TCP/IP STACK ........................................................................................................... 47 7.1 IMPLEMENTATION .................................................................................................... 47 8 TECHNICAL DATA ..................................................................................................... 48 9 CONTACT DETAILS ................................................................................................... 50 GBBA/SEM/BMS 03:0001 Rev A 4 GR47/GR48 Technical description 1 Introduction 1.1 Overview The GR47/GR48 belong to a new generation of Sony Ericsson Mobile Communications GSM modules. This document describes the main characteristics and functionality of the GR47/48, two dual band products for 900/1800 MHz and 850/1900 MHz GSM bands respectively. They are intended to be used in both machine-to-machine applications and man-to-machine applications. The module serves its purpose when there is a need for sending and receiving data (by SMS, CSD, HSCSD, or GPRS), as well as making voice calls over the GSM network. GR47/GR48 are business-to-business products. It is intended to be sold to manufacturers, system integrators, applications developersdeveloping solutions with wireless communication. The module is intended to be integrated by the system integrator within an application. The module and the external application will form a system for wireless communication. A typical system is one where a micro controller in an external application communicates with the module over its serial interface. The micro controller will control the module, via the supported set of AT commands. It is assumed that the system integrators have a high technical knowledge and the ability to integrate the module into a system. For the GR47/GR48 modules some interesting applications are the following: • Fleet and Asset Management • Vending Machines • Security and Alarm • Other telemetry applications GBBA/SEM/BMS 03:0001 Rev A 5 GR47/GR48 Technical description 1.2 Features The module performs a set of telecom services (TS) according to GSM standard phase 2+, ETSI and ITU-T. The functions of the module are implemented by issuing AT commands over the serial interface. Supported AT commands are listed in section 5, these are defined further in GSM 7.05/7.07 and the GR47/GR48 integrator’s manual. 1.2.1 Type of Mobile Station The GR4X family are normal dual band type of MS with the following characteristics. GR47 GSM 900 E-GSM 900 GSM 1800 Frequency Range (MHz) TX: 880-915 TX: 880-890 TX: 1710-1785 RX: 935-960 RX: 925-935 RX: 1805-1880 Channel spacing 200 kHz 200 kHz Number of channels 173 Carriers *8 (TDMA) 374 Carriers *8 (TDMA) GSM: Channels 1 to 124 DCS: Channels 512 to 885 E-GSM: Channels 975 to 1023 Modulation GMSK GMSK TX Phase Accuracy < 5º RMS Phase error (burst) < 5º RMS Phase error (burst) Duplex spacing 45 MHz 95 MHz Receiver sensitivity at antenna connector < - 102 dBm < - 102 dBm Transmitter output power at antenna connector Class 4 Class 1 2W (33 dBm) 1W (30 dBm) Automatic hand-over between GSM 900 and GSM 1800 GR48 GSM 850 GSM 1900 Frequency Range (MHz) TX: 824-849 TX: 1850-1910 RX: 869-894 RX: 1930-1990 Channel spacing 200 kHz 200 kHz Number of channels 123 carriers *8 (TDMA) 298 Carriers *8 (TDMA) GSM: Channels 128 to 251 PCS: Channels 512 to 810 Modulation GMSK GMSK TX Phase Accuracy < 5º RMS Phase error (burst) < 5º RMS Phase error (burst) Duplex spacing 45 MHz 80 MHz Receiver sensitivity at antenna connector < - 102 dBm < - 102 dBm Transmitter output power at antenna connector Class 5 Class 1 0.8 W (29 dBm) 1W (30 dBm) Automatic hand-over between GSM 850 and GSM 1900 GBBA/SEM/BMS 03:0001 Rev A 6 GR47/GR48 Technical description 1.2.2 SMS The module supports the following SMS services: • • • • Sending: MO, both PDU and Text mode supported. Receiving: MT, both PDU and Text mode supported. CBM is a service, in which a message is sent to all subscribers located in one or more specific cell(s) in the GSM network, for example, cell location information. SMS STATUS REPORT according to GSM 03.40. The maximum length of an SMS message is 160 characters when using 7-bit encoding. For 8-bit data, the maximum length is 140 characters. The module supports upto 6 concatenated messages to extend this function. 1.2.3 Voice calls The GR47/GR48 offers the capability of MO and MT voice calls, as well as supporting emergency calls. In addition to this multiparty, call waiting and call deflection features are available. Some of these features are operator specific. The module offers normal analogue input/output lines, analogue audio input/ output lines in differential modes, and digital audio interface, with the possibility of accessing internal points within the digital audio lines. Moreover, the GR47/GR48 have an embedded echo canceller and noise suppression, which provide high quality audio. The module supports HR, FR and EFR voice coding, provided that EFR is available in the network. 1.2.4 Data The module supports the following data protocols: • General Packet Radio Service (GPRS). The modules are Class B Terminals, which provides simultaneous activation and attach of GPRS and GSM services. The GR47/GR48 modules are GPRS 4+1 devices, which are capable of transmitting in one timeslot per frame (uplink), and receiving in a maximum of four timeslots per frame (downlink). • Circuit Switched Data (CSD). GR47/GR48 modules are capable of establishing a circuit switch data link at 9.6 kbps. • High Speed Circuit Switched Data (HSCSD). GR47/GR48 supports HSCSD communication, with one timeslot per frame capacity in the uplink and two timeslots per frame capacity in the downlink (2+1). GBBA/SEM/BMS 03:0001 Rev A 7 GR47/GR48 Technical description 1.2.5 SIM Card The module supports the connection of an external SIM Card with 3V or 5 V technology, via the 60-pin system connector. The module does not have an internal SIM holder. 1.2.6 Power consumption Stand-by Transmit/Operation GSM 850 & 900 MHz <5 mA 275 mA (2A peak) GSM 1800 & 1900 MHz <5 mA 250 mA (1.75A peak) Note! The power consumption during transmission is measured at maximum transmit power. 1.2.7 Other features • 07.10 Multiplexing • GPS interoperability • SIM application toolkit, class 2 release 96 compliant • Embedded application (see section 6) • On board TCP/IP stack (see section 7) 1.2.8 Development Kit Sony Ericsson Mobile Communications provides the opportunity to test the module in a limited scale, before ordering a large quantity. 1.2.8.1 M2mpower Package With the M2mpower package you can quickly get started with the module. The developer's Kit as part of the M2mpower Package includes necessary accessories (software and hardware) that you will need for your test purposes. It also includes the following: • GSM module GR47 or GR48 • Integrator’s Manual • M2mpower IDE • M2mpower application guide The Integrator’s Manual provides you with all the information you need to be able to integrate the module with your application. The Embedded Applications software IDE is supplied ready to run on a GBBA/SEM/BMS 03:0001 Rev A 8 GR47/GR48 Technical description suitable PC and comes with extensive help files, training course and support. 1.2.8.2 Developer’s kit As an alternative, the Integrator’s Manual and Universal Development Board are available as a separate offering. The kit includes other necessary accessories (software and hardware) that you will need for your test purposes These are available from your regional salesperson or M2M customer support (see section 7) 1.3 Precautions The GR47/GR48 should be handled like any mobile station. In the Integrators’ Manual you will find more information about safety and product care. In the Technical Data chapter in this document the environmental and electrical limits are specified. Never exceed these limits to ensure the module is not damaged. 1.4 Abbreviations Abbreviation Explanation ATMS Audio To Mobile Staition AFMS Audio From Mobile Station CBS Cell Broadcast Service CBM Cell Broadcast Messaging CSD Circuit Switch Data DCE Data Circuit Terminating Equipment DTE Data Terminal Equipment DTMF Dual Tone Multi Frequency EA Embedded Applications EFR Enhanced Full Rate codec EMC Electro-Magnetic Compatibility ETSI European Telecommunications Standards Institute FR Full Rate codec GPRS General Packet Radio Service GPS Global Positioning System GSM Global System for Mobile Comunication HR Half Rate codec HSCSD High Speed Circuit Switched Data IDE Integrated Developers Environment GBBA/SEM/BMS 03:0001 Rev A 9 GR47/GR48 Technical description IP Internet Protocol ITU-T International Telecommunication Union – Telecommunications Standardisation Sector ME Mobile Equipment MMCX Micro Minature Coax MO Mobile Originated MS Mobile Station MT Mobile Terminated PCM Pulse Code Modulation PDU Protocol Data Unit RLP Radio Link Protocol RF Radio Frequency RFU Reserved for Future Use RTC Real Time Clock SDP Service Discovery Protocol SMS Short Message Service SIM Subscriber Identity Module TCP Transport Control Protocol TBD To Be Defined UDP User Datagram Protocol GBBA/SEM/BMS 03:0001 Rev A 10 GR47/GR48 Technical description 2 Mechanical Description 2.1 Interface Description The picture below presents the conceptual mechanical design of the GR47/48. The GR47/GR48 are protected with AISI 304 Stainless Steel covers suitable to fulfil the environmental and EMC requirements. Dimensions, the position of the different connectors and mounting holes are shown in figure 2.2. Figure 2.1 GR 47/48, view from the underside GBBA/SEM/BMS 03:0001 Rev A 11 GR47/GR48 Technical description 2.2 Physical Dimensions Figure 2.2 Physical dimensions of GR 47/48 The measures are given in millimetres. See also chapter 6, Technical Data. GBBA/SEM/BMS 03:0001 Rev A 12 GR47/GR48 Technical description 3 System Connector Interface 3.1 Overview The electrical connections to the module (except the antenna), are made through the System Connector Interface. The connector shall allow the following connections: board to board and board to cable. Details of connector availability and sources are available from customer support on request. Figure 3.1 GR 47/48. View from the underside The table on next page provides the pin assignment of the different signals in the System Connector Interface as well as a short description of them. All signal directions are with respect to the module i.e. Direction 'O' means data being sent by the module. GBBA/SEM/BMS 03:0001 Rev A 13 GR47/GR48 Technical description Pin Signal Name Dir Signal Type Description 1. VCC - Supply Power Supply 2. DGND - - Digital Ground 3. VCC - Supply Power Supply 4. DGND - - Digital Ground 5. VCC - Supply Power Supply 6. DGND - - Digital Ground 7. VCC - Supply Power Supply 8. DGND - - Digital Ground 9. VCC - Supply Power Supply 10. DGND - - Digital Ground 11. CHG_IN - Batt Charge (power) Battery charging 12. DGND - - Digital Ground 13. IO5 I/O Dig 2.75 General Purpose input/output 5 ADC4 I Analogue Analogue to digital converter 4 ON/OFF I Internal pull up, open drain Turns the module on/off Dig. 3/5 V SIM card power supply 14. 15. SIMVCC - Former WAKE_B Power output for SIM Card from module 16. SIMPRESENCE I Internal pull up, open drain SIM Presence A "1" shall indicate that the SIM is missing; a "0" that it is inserted. 17. SIMRST O Dig. 3/5 V SIM card reset 18. SIMDATA I/O Dig. 3/5 V SIM card data 19. SIMCLK O Dig. 3/5 V SIM card clock 20. DAC O Analogue Digital to Analogue converter 21. IO1 I/O Digital, 2.75 General purpose input/output 1 KEYROW2 I IO2 I/O Digital, 2.75 General purpose input/output 2 ADC 5 I Analogue Analgue to digital converter 5 IO3 I/O Digital, 2.75 General purpose input/output 3 KEYROW3 I IO4 I/O KEYROW4 I 25. VRTC I Supply 1.8 V Voltage for real time clock 26. ADC1 I Analogue Analogue to digital converter 1 27. ADC2 I Analogue Analogue to digital converter 2 22. 23. 24. GBBA/SEM/BMS 03:0001 Rev A Keyboard row 2 Keyboard row 3 Digital, 2.75 General purpose input/output 4 Keyboard row 4 14 GR47/GR48 Technical description 28. ADC3 I Analogue Analogue to digital converter 3 29. SDA I/O 2.75, internal pullup I2C Data 30. SCL O 2.75, internal pullup I2C Clock 31. BUZZER O Dig. 2.75 Buzzer output from module 32. O3 O Dig. 2.75 General purpose output 5 KEYCOL3 O Keyboard column 3 DSR O Data Set Ready LED O IO6 I/O V IO O 33. 34. Dig. 2.75 Flashing LED General purpose I/O 6 Power Out 2.75 Module powered indication. The VIO is a 2.75 V output that could power external devices to transmit data towards the GSM device to a 75mA max. 35. TX_ON O Dig 2.75 This output shall indicate when the GSM module is going to transmit the burst. 36. RI O Dig. 2.75 Ring Indicator KEYCOL2 O Keyboard column 2 O2 O General purpose output 2 DTR I KEYROW1 I Keyboard row 1 IN1 I General purpose input 1 DCD O KEYCOL1 O Keyboard column 1 O1 O General purpose output 1 RTS I IO9 I/O CTS O KEYCOL4 O Keyboard column 4 O4 O General purpose output 4 41. TD I Dig. 2.75 Transmitted Data [former DTMS] 42. RD O Dig. 2.75 Received Data [former DFMS] 43. TD3 I Dig. 2.75 UART3 Transmission I/O7 I/O RD3 O I/O8 I/O 45. TD2 I Dig. 2.75 UART2 Reception [Former CTMS] 46. RD2 O Dig. 2.75 UART2 Transmission [Former CFMS] 37. 38. 39. 40. 44. GBBA/SEM/BMS 03:0001 Rev A Dig. 2.75 Dig. 2.75 Dig. 2.75 Data Terminal Ready Data Carrier Detect Request To Send General purpose I/O 9 Dig. 2.75 Clear To Send General purpose I/O 7 Dig. 2.75 UART3 Reception General purpose I/O 8 15 GR47/GR48 Technical description 47. PCMULD I Dig. 2.75 DSP PCM digital audio input 48. PCMDLD O Dig. 2.75 DSP PCM digital audio output 49. PCMO O Dig. 2.75 Codec PCM digital audio output 50. PCMI I Dig. 2.75 Codec PCM digital audio input 51. PCMSYNC O Dig. 2.75 DSP PCM frame sync 52. PCMCLK O Dig. 2.75 DSP PCM clock output 53. MICP I Analogue Microphone input positive 54. MICN I Analogue Microphone input negative 55. BEARP O Analogue Speaker output positive 56. BEARN O Analogue Speaker output negative 57. AFMS O Analogue Audio output from module 58. SERVICE I 12V/2.7V Flash programming voltage for the MS. Enable logger information if no flashing Former VPPFLASH 59. ATMS I Analogue Audio input to module 60. AGND - Analogue Analogue ground Note : Although the pin out has changed the unit remains backwardly compatible with the GM47. 3.2 General Electrical and Logical Characteristics Many of the signals present in the interface are high-speed CMOS logic inputs or outputs powered from 2.75 V ± 5 %. Whenever a signal is defined as Dig. 2.75 V, the following electrical characteristics shall apply. Parameter Min. Typ. Max. Units Output Current Io High Level Output Voltage (V OH ) 2.2 2.75 Volts - 2 mA Low Level Output Voltage (V OL) 0 0.6 Volts 2 mA High Level Input Voltage (V IH ) 1.93 2.75 Volts Low Level Input voltage (V IL) 0 0.5 Volts GBBA/SEM/BMS 03:0001 Rev A 16 GR47/GR48 Technical description 3.2.1 General Protection Requirements All 2.75V digital inputs shall continuously withstand any voltage from -0.5V up to 3.47V (3.3V + 5%) in the power-on or power-off condition with no damage. All 2.75V digital outputs shall continuously withstand a short circuit to any voltage within the range from 0V to 3V. ! Note : This is for protection ONLY, the module cannot be driven directly by a 3.3V micro processor, if this is done it will invalidate any warranty claim on the module. The SIM output signals and the SIMVCC supply can continuously withstand a short circuit to any voltage within the range from 0V to 4.1V. GBBA/SEM/BMS 03:0001 Rev A 17 GR47/GR48 Technical description 3.3 Grounds Pins Name Description 2, 4, 6, 8, 10, 12 DGND Digital Ground 60 AGND Analogue Ground There are two ground signals in GR 47/48, Analogue Ground (AGND) and Digital Ground (DGND). The analogue Ground is connected to pin number 60, and the Digital Ground is connected to the System Connector Interface through pin numbers 2, 4, 6, 8, 10 and 12. Note: All the Ground pins have to be connected to the application. The AGND is connected to the DGND in the ME, and only there. It is important that the AGND and the DGND are separated in the application. 3.3.1 The Analogue Ground The AGND lead is the analogue audio reference ground. It is the return signal for Audio To Mobile Station (ATMS) and Audio From Mobile Station (AFMS). It shall be connected to the Digital Ground (DGND) inside the module and only there. The application shall not connect DGND and AGND. Parameter Limit Imax ≅12.5mA 3.3.2 The Digital Ground (DGND) DGND is the reference for all digital signals in the System Interface. It shall also be the DC return for the power supply on VCC and SERVICE. Each DGND pin is rated at 0.5 A. All DGND pins are connected internally in the module. All DGND pins should be connected commonly in the application. Parameter Limit Iaverage < 0.5 A No DGND pin can withstand over 0.5 A Imax < 600 mA (100 mA each) GBBA/SEM/BMS 03:0001 Rev A 18 GR47/GR48 Technical description 3.4 Regulated Power Supply Pins Name Description 1, 3, 5, 7, 9 VCC Regulated Power Supply The regulated power supply, VCC, is connected to the pin numbers 1, 3, 5, 7 and 9. 3.4.1 Power Supply (VCC) The VCC supplies the module with external power. Any other voltage needed is generated internally. Parameter Mode Limit Voltage to be applied Nominal 3.6 Volts Tolerance including ripple 3.4 Volts - 4.0 Volts 1 Over voltages Current Drive capability at TX Full Power 5.5 Volts < 600 mA (average)) < 2 A (Peak) GR 47/48 have not internal capacitance to supply the large current peaks during GSM transmission. Therefore on burst transmission the application DC source is responsible for providing the appropriate current. Design application notes are available from customer support on request. 3.4.2 Battery Charging Input (CHG_IN) The battery charging pin is design to provide a charging current into a battery. The precise algorithm is TBD but it will be one of the following • • 1 Generic charging algorithm implemented and further refinements for the algorithm to be implemented through embedded applications (see section 6) Specific charging algorithms for SEM approved batteries. Measured at system connector pins. GBBA/SEM/BMS 03:0001 Rev A 19 GR47/GR48 Technical description 3.5 ON/OFF and External Power Signals Pins Name Dir Description 14 ON/OFF I Square signal to turn on/off the module 34 VIO O External power supply 3.5.1 Module ON/OFF The module is powered ON/OFF by grounding (pulling low) pin 14 as per figure 3.2 below. The pin should then be released as it has an internal pull up to return it to the high state. Note: Driving with 2.75V or 3.6V is not permitted and restricts module functionality. Parameter Minimum Typical Voltage HIGH Level (FALSE) Maximum Units VCC By internal pull up only Voltage LOW Level (TRUE) 0 0.3*VCC Volts Pull-up Resistance Internal pull up 39 KΩ Figure 3.2ON/OFF and VIO performance Where the times are defined as follows: Time Description Min Typ tmr Time to start an ON/OFF operation 1 1.5 tpwr Time for module start-up once ON/ OFF signal has set to TRUE 100 GBBA/SEM/BMS 03:0001 Rev A Max Unit S 200 mS 20 GR47/GR48 Technical description 3.5.2 External 2.75 V (VIO) The VIO has been derived from a 2.75 V regulator. It is possible to use this output as a power supply at 2.75 V with a maximum of 75mA. It will indicate that the module is alive and it could power external devices. In this case, the external applications do not need to implement a 2.75 volt regulator to adapt the incoming (from module point of view) serial data. Parameter MinimumTypical Maximum Units Output Voltage (Iload =50 mA) 2.70 Load current GBBA/SEM/BMS 03:0001 Rev A 2.75 2.85 Volts 75 mA 21 GR47/GR48 Technical description 3.6 Analogue Audio Pins Name Dir Description 57 AFMS O Audio From Mobile Station 59 ATMS I Audio To Mobile Station 60 AGND - Reference for analogue audio ATMS and AFMS are the audio input and output for the module. The analogue audio signals can be used in two different modes, Handsfree and Portable Handsfree. Handsfree This mode is referred to as Audio To Mobile Station (ATMS) and Audio From Mobile Station (AFMS). It is used by audio accessories such as Handsets and Handsfree equipment. Portable Handsfree This mode activates a different amplification factor in the Mobile Equipment (ME). It also activates a microphone bias level in ATMS. This is the default mode. 3.6.1 Audio To Mobile Station (ATMS) ATMS is the analogue audio input to the module. It connects to the audio input of the CODEC in the module. The CODEC then converts the analogue audio to digital audio, in PCM format, which is connected to the internal PCM bus in the module. The internal PCM bus connects the encoded audio to PCMO on the system connector. ATMS is also used as the microphone input from the Portable Handsfree. If this is the case, a DC bias is provided from the ATMS. All sources must be AC-coupled except the Portable Handsfree microphone, which shall be DC-coupled in order to supply DC current to the Portable Handsfree microphone. AC coupling prevents incorrect biasing or damage of the ATMS input. The capacitor must have a value greater than shown below to avoid attenuation of low frequencies. The ATMS input is a passive network followed by the transmit part of the CODEC. GBBA/SEM/BMS 03:0001 Rev A 22 GR47/GR48 Technical description Parameter Limit Application driving impedance (0.3 - 3.5 kHz) < 300 Ω AC coupling capacitance > 1 µF 2 Module input impedance (0.3 - 3.5 kHz) >50ΚΩ Low frequency cut-off (- 3 dB) 300 Hz ± 50 Hz High frequency cut-off (- 3 dB) > 3500 Hz Maximum allowed input level 1.5V pp = 530mV Output DC bias level Handsfree mode 2V Portable Handsfree mode 2 V ± 0.1 V Additional Gain in Portable Handsfree mode 28.5 dB • Maximum input level at ATMS 245mV rms output at PCMO = 3dBm0. • The following table is with nominal PGA (Programmable Gain Settings). • For more information see AT commands in the integrators manual. Input Input Volts mVrms TXAGC dB AUXI1 Gain PCMO dBm0 ATMS 245 0 13 3 Maximum input level at MICI 61.4mV rms output at PCMO = 3dBm0 Input Input Volts mVrms TXAGC dB AUXI1 Gain PCMO dBm0 MICI 61.4 0 25 3 Output at AUX02 for 3dBm0 at PCMI Input dBm0 RXPGA Volume Control dB AUX02 mVrms PCMI 3dBm0 0 0 436 Output at BEAR for 3dBm0 at PCMI 2 Input dBm0 RXPGA Volume Control dB BEAR mVrms PCMI 3dBm0 0 0 388 AC coupling capacitance must be supplied by the application, unless a DC coupled microphone is used. GBBA/SEM/BMS 03:0001 Rev A 23 GR47/GR48 Technical description 3.6.2 Audio From Mobile Station (AFMS) AFMS is the analogue audio output from the module. When it is active, the output is derived from the PCM digital audio by the decoder part of the CODEC. The PCM data comes from PCMI on the system connector. It is also used as an ear-piece driver for the Portable Hands Free accessory. Parameter Limit Speaker impedance 64 Ω το 1ΚΩ AFMS Output Capacitance 2.2 µF ±10% Levels (THD < 5 %) 3.7 Drive capability into 5 kΩ (0.3 - 3.5 kHz) > 2.4 Vpp [TBC] Drive capability into 1.5 kΩ (0.3 - 3.5 kHz) > 2.2 Vpp [TBC] Drive capability into 150 Ω (at 1kHz) > 1.3 Vpp [TBC] Microphone Signals Pin Speaker signals Dir Function 53 MICP I Microphone Positive Input 54 MICN I Microphone Negative Input MICP and MICN are the microphone-input pins. These inputs shall be compatible with an electret microphone. The microphone contains a FET buffer with open drain output, which must be supplied with at least +2V relative to ground. Figure 3.3 Microphone connection to module CCO is the internal source voltage that will provide the necessary drive current for the microphone (This is not provided by the module). GBBA/SEM/BMS 03:0001 Rev A 24 GR47/GR48 Technical description Parameter CCO 3.8 Limit 2.0 - 2.5 V Speaker Signals Pin Speaker signals Dir Function 55 BEARP O Microphone Positive Output 56 BEARN O Microphone Negative Output BEARP and BEARN are the speakers output pins. These outputs are in differential mode. 3.9 Digital Audio Pin PCM signal Dir Function 52 PCMCLK O PCM clock 51 PCMSYNC O PCM frame sync 47 PCMULD I PCM audio input to DSP 48 PCMDLD O PCM audio output to DSP 50 PCMI I PCM audio input to Codec 49 PCMO O PCM audio output to Codec The digital PCM audio signals allow the connection of a digital audio source / receiver, bypassing the analogue audio CODEC processing functions performed within the module. Figure 3.4 Pin connections to digital audio GBBA/SEM/BMS 03:0001 Rev A 25 GR47/GR48 Technical description In the case where no external audio processing is performed, then it is necessary to connect the following signals at the system connector: PCMDLD and PCMI PCMULD and PCMO Electrical characteristics The Dig. 2.75 V CMOS Output / Input electrical characteristics shall apply, with DGND as the reference. PCM interface format The PCM format (for PCMULD and PCMDLD) shall follow a linear PCM data I/O format of an industry standard Texas Instrument DSP. It is the same format as the one used between the CODEC and the DSP. The DSP is the source of the bit clock PCMCLK and the frame synchronisation PCMSYNC. The data bits in PCMULD and PCMDLD shall be aligned so that the MSB in each word occurs on the same clock edge. GBBA/SEM/BMS 03:0001 Rev A 26 GR47/GR48 Technical description 3.10 Serial Data Pin Name Dir Description RS232 CCITT Nº 41 TD I Serial data to module 103 42 RD O Serial data from module 104 39 RTS I Request To Send 105 IO9 I/O General purpose I/O 9 CTS O Clear To Send KeyCOL4 O Key column 4 O4 O General purpose output 4 DTR I Data Terminal Ready KeyROW1 I Keyboard column 1 40 37 I/O1 38 O Data Carrier Detect KeyCOL1 O Key column 1 O4 O General purpose output 1 RI O Ring Indicator KeyCOL2 O Key column 2 O2 O General output 2 45 TD2 I UART 2 Data Transmission 46 RD2 O UART 2 Data Reception 43 TD3 O UART 3 Data Transmission 44 RD3 I UART 3 Data Reception GBBA/SEM/BMS 03:0001 Rev A 108.2 General purpose I/O 1 DCD 36 106 109 125 27 GR47/GR48 Technical description The serial channels are used as asynchronous communication links between an application system or accessory units connected to the Module. They consist of three UART's. • • • UART 1 – This has full RS232 and is used for all on and off line communication. UART 2 – May be used for interfacing to a GPS unit, downloading software, receiving logging information, etc. UART 3 – May be used by embedded applications. The Dig. 2.75 V CMOS Output / Input electrical characteristics shall apply, with DGND as the reference. Extra relevant data is specified for some of the signals. The character format supported is, 1 start bit, 8 bit data, non-parity plus 1 stop bit, in total 10 bits per character. Note : As stated in section 3.2.1 the module is unable to directly interface to a 3.3V micro processor. Note 2 : As can be seen from the pin out table, several of the RS232 pins have multiple functionality, this is user selectable with the RS232 functionality set as default. GBBA/SEM/BMS 03:0001 Rev A 28 GR47/GR48 Technical description 3.10.1 UART 1 (RS232) - RD, TD, RTS, CTS, DTR, DCD, DSR and RI The UART1 signals form a 9 pin RS-232 (V.24) serial port. The signal levels do not match the standard RS-232 (V.28) levels. The relationship between the levels is shown in the table below RS - 232 Level RD, TD RTS, CTS, DTR, DCD, RI 2.75 V CMOS Level <-3V 1 OFF > 1.93 >+3V 0 ON < 0.80 V Conversion between the 2.75V CMOS levels and the RS232 levels can be achieved using a standard interface IC, such as the Maxim Integrated Products MAX3237. 3.10.2 Serial Data Signals - RD, TD The default baud rate is 9.6 kbit/s, however higher bit rates up to 460 kbit/s are supported and are set by the AT+IPR command. The UART 1 starts at a rate of 9.6 kbit/s in standard AT mode or binary mode (First received data AT or binary will determine the operation mode). The GSM 07.10 multiplexing protocol is supported and is started on command, in this case bit rates up to 460 kbits/s are supported. Serial Data From Module (RD) RD is an output used to send data on the UART 1 to the application system. This is a Dig. 2.75 CMOS Output and general characteristics are applicable. Parameter Limit Application load resistance < 100 kΩ Application load capacitance < 500 pF Serial Data To Module (TD) TD is input (to the module) used by the application system to send data on the UART 1 to the module. This is a Dig. 2.75 CMOS Input and general characteristics are applicable. Parameter Limit Application driving impedance < 100 Ω Input capacitance 1 nF Input resistance (pull-down) 100 kΩ to 2.75 V GBBA/SEM/BMS 03:0001 Rev A 29 GR47/GR48 Technical description 3.10.3 Control Signals - RTS, CTS, DTR, DCD, RI, DSR The control signals are active low, and hence when a standard interface IC is used (such as MAX3237), then standard RS-232 levels are obtained. These signals together with DGND, RD and TD form a 9-pin RS-232 data port (with the exception of the voltage levels). RTS and CTS shall be capable of transmitting at 1/10 of the data transmission speed for data rates, up to 460 kbit/s. (Byte oriented flow control mechanism). Switching times for RTS and CTS Parameter Limit Time from Low to High level < 2 µs Time from High to Low level < 2 µs Request to Send (RTS) RTS is an input to the module. The signals on this circuit are used to condition the DCE (the module when used for data transmission purposes) for data transmission. Default level is OFF, by internal pull up. The exact behaviour of RTS is defined by the AT+IFC command. Software or hardware flow control can be selected. Hardware flow control is the default. This is a Dig. 2.75 CMOS Input and general characteristics are applicable. It is the duty of the application to pull RTS low (logic levels) to request communications with the module. The module will respond by asserting CTS low and as such may be used as a notification as a module status ready for communication. Parameter Limit Application driving impedance < 100 Ω Input capacitance < 2 nF Input resistance (pull-down) 100 kΩ to DGND GBBA/SEM/BMS 03:0001 Rev A 30 GR47/GR48 Technical description Clear To Send (CTS) CTS is an output from the module. The signals on this circuit are used to indicate that the DCE (the module when used for data transmission purposes) is ready to transmit data. Default level is high. The exact behaviour of CTS is defined by the AT+IFC command. Software or hardware flow control can be selected. This is a Dig. 2.75 CMOS Output and general characteristics are applicable. Tip: if only software flow control is to be used it becomes necessary to assert RTS low or to connect RTS to CTS at the module. Parameter Limit Application load capacitance < 500 pF Application load resistance > 1 MΩ Data Terminal Ready (DTR) DTR is an input to the module. Signals from the DTE on this circuit indicate the DTE is ready to transmit and receive data. DTR also acts as a hardware 'hang-up' so that calls are terminated if DTR is OFF (high). Default level is ON (low). The exact behaviour of DTR is defined by the AT&D command. This is a Dig. 2.75 CMOS Input and general characteristics are applicable. Data Carrier Detect (DCD) DCD is an output from the module. An ON (low) signal shall indicate that a valid carrier (data signal) is being received by the DCE (module). The exact behaviour of DCD is defined by the AT&C command. This is a Dig. 2.75 CMOS Output and general characteristics are applicable. Ring Indicator (RI) RI is an output from the module. An ON (low) signal indicates a ringing signal is being received by the DCE (module). This is a Dig. 2.75 CMOS Output and general characteristic s are applicable. GBBA/SEM/BMS 03:0001 Rev A 31 GR47/GR48 Technical description DSR (Data Set Ready) The DSR signal must be switched on using the at&s command. If DSR is enabled it will indicate an active state (low) if the module is in command mode and inactive (high) if the module is in on line data mode. 3.10.4 UART 2 - TD2, RD2 The UART 2 consists of a full duplex serial communication. This involves the transmission and reception lines. The communication port shall work in one mode: Operation and Maintenance mode. Operation and Maintenance mode shall work in addition with the SERVICE signal. On switching the module on, if SERVICE signal is active then two events can happen. If no data is sent to the module, then the logger is activated. Otherwise, the module shall be ready to be reprogrammed. Timing and Electrical signal characteristics equal to UART 1 TD and RD, except for maximum baud rate that could be increased to 921 kbps. Transmitted Data 2 (TD2) TD2 is input (to the module) used by the application system to send data on the UART 2 to the module. The electrical characteristics shall be the same as TD. Received Data 2 (RD2) RD2 is an output used to send data on the UART 2 to the application system. The electrical characteristics shall be the same as RD. 3.10.5 UART 3 - TD3, RD3 The UART 3 consists of a full duplex serial communication. This involves the transmission and reception lines. Timing and electrical signals characteristics equal to UART 1 TD and RD. GBBA/SEM/BMS 03:0001 Rev A 32 GR47/GR48 Technical description Transmitted Data 3 (TD3) TD3 is input (to the module) used by the application system to send data on the UART 3 to the module. The electrical characteristics shall be the same as TD. Received Data 3 (RD3) RD is an output used to send data on the UART 3 to the application system. The electrical characteristics shall be the same as RD. 3.11 SIM Card related signals Parameter Mode Signal Min. Typ. Max. Uni t SIM supply Voltage 3V SIMVCC 2.7 3.0 3.3 V 4.5 5.0 5.5 V 2.1 3.0 V 3.5 5.0 V 0 0.9 V 0 1.5 V 2.7 3.0 V 4.7 5.0 V 0 0.2 V 0 0.2 V 2.4 3.0 V 4.4 5.0 V 0 0.35 V 0 0.3 V 5V High Level Input Voltage (V IH) 3V SIMDAT 5V Low Level Input Voltage (V IL) 3V SIMDAT 5V High Level Output Voltage (V OH ) 3V SIMDAT 5V Low Level Output Voltage (V OL ) 3V SIMDAT 5V High Level Output Voltage (V OH ) 3V SIMCLK SIMRST 5V Low Level Output Voltage (V OL ) 3V SIMRST 5V GBBA/SEM/BMS 03:0001 Rev A SIMCLK 33 GR47/GR48 Technical description 3.11.1 SIM Detection – SIM Presence SIMPRESENCE is an input intended to be used to determine whether a SIM card has been inserted or removed in the external SIM card holder. It shall be normally wired to the "Card Inserted Switch" of the external SIM card holder. When left open an internal pull up resistor maintains the signal high and means ‘SIM card missing’ to the module. When pulled low the module assumes a SIM card is inserted. SIMPRESENCE is a digital CMOS 2.75 input with the following characteristics. Parameter Min. Pull-up resistance (at 2.75 V) 100 Typ. Units kΩ Low Level Input Voltage (SIM inserted) High Level Input Voltage (SIM missing) Max. 1.93 0.8 V 5 V Note : The module has been Type Approved with SIM presence implemented, to avoid extra testing when type approving the application this should be designed in. 3.12 Service/Programming Pin Signal Description 58 SERVICE Flash programming voltage This input shall be used as a programming voltage for the Flash Memory to initiate and it is also used as a signal to indicate to the module that it should start outputting logging information. Mode SERVICE Voltage (V) Min. Typ. Normal Operation Service/enable programming Absolute maximum voltage GBBA/SEM/BMS 03:0001 Rev A 1.9 2.75 Drive Capacity Max. 0.8 - 3.6 > 1 mA 13.5 - 34 GR47/GR48 Technical description 3.13 Buzzer Pin Signal Description 31 Buzzer Buzzer output from the module This is an output signal which allows the application to use preprogrammed melodies or sounds. Typical use would involve a transistor buffer with a piezoelectric sounder. The Dig. 2.75 V CMOS Output electrical characteristics shall apply, with DGND as the reference. 3.14 LED Pin Signal Description 33 LED LED Output from module I/O6 General purpose I/O 6 This is an output signal which allows the use of an external LED. The LED shall indicate different states within the module. This signal is a Dig. 2.75 V CMOS output so general characteristics are applicable. In order to connect a LED in the external application the following scheme shall be followed. The operation of the LED is hardcoded and is not controlled by the host application. Figure 3.5 Electrical connection for LED GBBA/SEM/BMS 03:0001 Rev A 35 GR47/GR48 Technical description 3.15 TX_ON - Burst Transmission Pin Signal Dir Description 35 TX_ON O GSM module on transmission The TX_ON is a digital signal output. This shall indicate that the module is going to transmit the burst. Burst transmission is the time when a GSM transceiver unit is transmitting in its timeslot assigned by the network. Dig 2.75 CMOS Output so general electrical characteristics are applicable. 3.16 Real Time Clock The Real Time Clock provides the module with a time-of-day calendar with alarm and one hundred-year calendar to the main microprocessor. The real time clock operates with a separate power supply. Therefore, two modes of operation shall be distinguished: • • RTC Normal operation: This is when the MS is powered/Vcc present and it does not take into account if the MS is in OFF or ON. RTC Backup operation: This operation is performed when the MS is not powered, VCC = 0V. In this case the RTC operation is maintained by the backup power supply. The backup power supply is a passive power supply, capacitor, golden- capacitor, battery etc., which shall be connected outside the MS to VRTC pin. During the RTC normal operation, the passive power supply is being charged; this is like charging a capacitor. In backup operation, the backup source provides with enough voltage for RTC operations. The following table shows both voltage operations characteristics. Parameter Min. Typ. Max. Units Supply Voltage RTC (Normal Operation – Charging the capacitance) 1.6 1.8 2.0 V Supply Voltage RTC (Backup Operation – Capacitance provides with voltage) 1.0 1.8 2.0 V 5.0 10.0 µA Current drawn GBBA/SEM/BMS 03:0001 Rev A 36 GR47/GR48 Technical description In Back-up operation if the voltage drop below 1 Volt, the RTC shall stop working. The following diagram shows the RTC connection: Figure 3.6 RTC connection 3.17 Extended IO capabilities In order to increase the flexibility and variety of GR47 peripherals, the RS232 hardware flow control shares its physical interface with the keypad scanning interface and extended general purpose IO capability. Due to the nature of this sharing, it is not feasible to operate all these features concurrently (although, with care, dynamic switching from one feature to another and back is possible). When a particular feature is required of an IO, the software automatically sets the states of the relevant IO blocks disabling one set and enabling others. This is most noticeable with the RS232 hardware flow control when switching on the keypad functionality. If full hardware flow control and handshaking is required there will be no available keypad column drivers and the keypad interfacing will be disabled. If intermediate hardware flow control is selected (RTS and CTS only), the unused flow control pins (DTR, DCD, RI, DSR) are made available to the keypad interface providing three discrete matrix column drivers. If RS232 hardware flow control is switched off altogether, the remaining keypad column driver is enabled allowing the full keypad matrix of 5 columns by 4 rows. 3.17.1 LED/IO6 The LED function pin can be used as a general purpose digital IO when the flashing LED function is not required. However, this pin does not have an on-board pull-up resistor. It is required that an external pull-up or pull-down resistor be provided by the host circuitry when either not used or when used as a digital input. GBBA/SEM/BMS 03:0001 Rev A 37 GR47/GR48 Technical description 3.17.2 I#/O# When not being used for an alternative function the pins labelled I# and O# may be used for general purpose inputs or outputs respectively. The inputs have an on-board 100k pull-up resistor and the outputs are driven rail-to-rail at 2.75V levels. 3.17.3 UART3/IO# The UART3 pins have been given alternative functions as general purpose I/O, both pins may be used for either input or output. However, the TX pin has a 100kO pull-down resistor to ground and the RX pin has a 100kO pull-up resistor to 2.75V. This must be taken into consideration when designing the host circuit. 3.17.4 IO#/ADC# To increase analog input capabilities, the GR47 optimises the IO by multiplexing or sharing different features on single pins. There are two digital IO pins which now have an additional ADC input. When configured as digital IO, the software will not read the voltages at the two new ADC inputs. When configured as ADC inputs the software will configure the digital IO pins as input or high impedance tri-state. In this state any applied voltage between 0V and 2.75V can be read as an 8 bit value. Because the additional ADC inputs (ADC4 and ADC5) are common with digital IO, the input circuit of the ADC is not the same as for the original circuits ADC1-3. It is important to understand the input structure of the pin so that the correct analog voltage is read by the application. The input structure is provided in figure 3.7. It consists of a 100kO pull-up to 2.75V followed by a series 1kO and 10nF capacitor to ground which make a low pass filter with a 3dB roll-off at about 16kHz. The input impedance of the analog IC is 1MO minimum. 2.75V 2.75V >1MO 100kO 1kO IO5/ADC4 ADC 10nF Analog IC Figure 3.7 Input circuit for combined digital IO and ADC pins GBBA/SEM/BMS 03:0001 Rev A 38 GR47/GR48 Technical description 3.18 Keyboard interface To increase IO capabilities, the GR47 optimises the IO by multiplexing or sharing different features on single pins. The IO has been extended to allow simple interfacing of a matrix keypad. 3.18.1 IO#/KEYROW# When configured for keypad operation the software will configure the digital IO pins as input or high impedance tri-state. In this state, the keypad matrix row can be read from the KEYROW# inputs. These pins have a 100kO pull-up to 2.75V and the rows are considered activated when the voltage is pulled low by the external keypad switches. 3.18.2 KEYCOL# The keypad matrix column drivers share functionality with the RS232 hardware flow control signals. When configured for keypad operation the software will configure the hardware flow control to either intermediate or off. With intermediate flow control the number of keypad column outputs is limited to three, with flow control switched off, the number of keypad column outputs is increased to four. In addition to the keypad column outputs it is possible to use a direct ground connection as an additional column driver, which is interpreted as column zero. Thus it is possible to create a variety of keypad matrix sizes from single column to five columns wide. Finally, a standard keypad matrix directly connects the rows to the columns whenever a key is depressed. In order to avoid short circuits if multiple keys are pressed simultaneously, the column drivers must be open-collector. This must be achieved with external transistors as the logic drive from the GR47 is rail-to-rail. Suitable transistors for this interface are of the type with built in bias resistors between base and emitter. The method of connection is shown in 3.8 below. GBBA/SEM/BMS 03:0001 Rev A 39 GR47/GR48 Technical description KEYROW# 1 2 3 4 5 6 GR47 RN1107 KEYCOL# RN1107 RN1107 Figure 3.8 Keyboard matrix connections GBBA/SEM/BMS 03:0001 Rev A 40 GR47/GR48 Technical description 4 Antenna Connector The Antenna Connector is a hub for transmission of the Radio Frequency (RF) signals from the module to the external customersupplied antenna. It is a MMCX connector that is mounted on the surface of the module. Most dealers should be able to supply this type of connector. This table provides the electrical characteristics at the antenna interface. Parameter Nominal impedance Limit Output Power 2 Watt peak (Class 4) Extended GSM 900 1 Watt peak (Class 1) GSM 1800 Better than - 102 dBm Extended GSM 900 Better than - 102 dBm GSM 1800 Static Sensitivity GBBA/SEM/BMS 03:0001 Rev A Description 50 Ω (SWR < 2:1) 41 GR47/GR48 Technical description 5 AT Command Summary The AT standard is a line-oriented command language. "AT" is an abbreviation of ATtention and it is always used to start sending a command line from a TE to the TA. TE stands for Terminal Equipment which is a computer of any size and TA stands for Terminal Adapter which is the modem part of the module. The command line consists of a string of alphanumeric characters. It is sent to the modem to instruct it to perform the commands specified by the characters. Functionality AT commands CONTROL AND IDENTIFICATION Subscriber Information AT+CNUM, AT+CIMI, AT*ESNU Product & Release info AT+CGMR, AT+CGSN, AT*ESIR Generic information & Settings AT, AT*, AT+CLAC, AT+GCAP, ATI, AT+CSCS, AT&F, AT&W, ATZ, AT+WS46, AT*E2SSN CALL CONTROL General call control ATA, ATD, ATL, ATH, ATP, ATT, AT+CHUP, AT+CMOD, AT+CVHU, AT+CR, AT+CRC, DTMF AT+VTS Data commands ATO, AT+CRLP AUDIO CONTROL Audio profile modification AT*E2EAMS Audio profile manipulation AT*EALR, AT*EAMS, AT*EARS, AT*ELAM, AT*EMIR, AT*EMIC, AT*EXVC, AT*E2APR NETWORK SERVICES Alternate Line Service (ALS) AT*EALS, AT*ELIN, AT*ESLN Customer Service Profile AT*ECSP Call forwarding AT+CCFC, AT*EDIF Calling/called number identification AT+CLIP, AT+CLIR, AT*EIPS Preferred networks AT*EPNR, AT*EPNW Advice of Charge AT+CACM, AT+CAMM, AT+CAOC, AT+CPUC Calling cards AT*ESCN Call hold, waiting & multiparty AT+CCWA, AT+CHLD Operator selection AT+COPS GBBA/SEM/BMS 03:0001 Rev A 42 GR47/GR48 Technical description Network registration AT+CREG USSD AT+CUSD, AT+CSSN Security & Locks AT+CLCK, AT+CPWD, AT+CPIN, AT*EPEE SETTINGS Restting AT*EMAR Ring signal settings AT*ERIL, AT*ERIN, AT*ERIP, AT*ESIL, AT*ESMA, AT*ESMM, AT*ESOM ME STATUS INFORMATION AT*ECAM, AT+CSQ, AT+CIND, AT+CPAS, AT+CMER ERROR CONTROL AT+CMEE, AT+CEER SMS & CB Settings AT*ESTL, AT+CPMS, AT+CRES, AT+CSAS, AT+CSCA, AT+CSMS, AT+CNMI, AT+CSDH, AT+CSMP, AT+CGSMS SMS-Command AT+CMGC Read / write SMS AT+CMGD, AT+CMGW, AT+CMGL, AT+CMGR Send SMS AT+CMGS, AT+CMSS PHONEBOOK Read / write / find AT+CPBS, AT+CPBR, AT+CPBW, AT+CPBF Groups AT*EGIR, AT*ESAG, AT*ESCG, AT*ESDG, AT*ESDI, AT*ESGR Personal Rings AT*EPRR, AT*EPRW Settings AT*EPBM, AT*E2PBCS CLOCK Alarm AT+CALA, AT+CALD, AT+CAPD Time & Date AT+CCLK, AT+CTZU, AT*EDST INTERFACE COMMANDS Flow control AT&C, AT&D, AT+ICF, AT+IFC, AT+IPR, AT&S S registers ATS0, ATS10, ATS2, ATS3, ATS4, ATS5, ATS6, ATS7, ATS8 Response control AT+ILRR, ATE, ATV, ATQ, AT+CSCS, ATX 07.10 MULTIPLEXING AT+CMUX GBBA/SEM/BMS 03:0001 Rev A 43 GR47/GR48 Technical description HSCSD AT+CHSR, AT+CHSU GPRS PDP Context Activation AT+CGACT GPRS Attachment AT+CGATT Enter Data State AT+CGDATA Define PDP Context AT+CGDCONT GPRS Event Reporting AT+CGEREP Show PDP Address AT+CGPADDR Quality of Service Profile (MINIMUM ACCEPTABLE) AT+CGQMIN Quality of Service Profile (REQUESTED) AT+CGQREQ GPRS Network registration Status AT+CGREG Extension of ATD for GPRS ATD* NETWORK INFORMATION Cell information AT*E2CD Engineering Mode AT*E2EMM SIM APPLICATION TOOLKIT Set Up Call AT*E2STKC Display Text AT*E2STKD Get Inkey AT*E2STKG Get Input AT*E2STKI Select Item AT*E2STKL Set Up Menu AT*E2STKM Envelope (Menu Selection) AT*E2STKN Application Toolkit Settings AT*E2STKS GBBA/SEM/BMS 03:0001 Rev A 44 GR47/GR48 Technical description 6 Embedded applications The module has the capability to store and run customer written code in the form of a script during the processors idle time, through the use of an on board interpreter. 6.1 Features Main features of embedded applications are as follows. • • • • 6.2 C based scripting language (SEM specific) Over the air upgradeable (scripts, NOT signalling software) Library of intrinsic functions Multiple on module script support Implementation The module has upto 44k of space available for storage of two scripts in the scripting language and 25k of operating RAM. Structures included in this language are • • • If - then - else statements While loops For loops All hardware interfaces that are normally available to the module through the AT commands are available to the embedded application. Further drivers have been written such as M bus and I2 C for use by the EA through the use of the IO pins. 6.2.1 Limitations Since the module is processing the script using its own memory limitations are placed onto the scripts that are run. • • • GBBA/SEM/BMS 03:0001 Rev A A direct comparison cannot be made to a fully compiled C program in terms of size but a gauge of script size is that if each line were 128 characters long in the script then the script could be 350 lines long. Processing power is something that needs to be considered as the script is run as a low priority process within the software. An option that can be used to stop this controller mode , this stops GSM operation and provides all processing power for the script to be run. Code cannot be ported directly from an existing application and loaded directly onto the module. It must be re written in the SEM script language so that the module interpreter can function correctly. 45 GR47/GR48 Technical description 6.2.2 M2mpower IDE (Integrated Developers Environment) The IDE is a windows based package which allows the user to write simulate, de-bug and download their application into a module with the EA software. The standard version is designed to run on Windows XP and 2000, other versions are available for 98 if required. A guide is available for implementing applications using the developers kit and the EA functionality. This is a required package to be able to implement an EA. For further information please contact SEM customer support. GBBA/SEM/BMS 03:0001 Rev A 46 GR47/GR48 Technical description 7 TCP/IP stack An on board IP/TCP/UDP stack has been integrated into the software negating the need for the customer to implement one in their own code base. This is going to initially only be accessible through the embedded applications (see previous section) using intrinsic functions. 7.1 Implementation There are a number commands allowing various functions , these are as follows. • • • • Open/closing IP connection – Negotiates/closes a dynamic IP address with the web server. Send/Receive TCP packets – Performs all TCP operations to send and receive packets. Send/Receive UDP packets – Performs all UDP operations to send and receive packets. Resolve URL to an IP address - Similar to nslookup command in DOS When the unit is set up and controlled using the embedded applications either the EA or an external application can generate data to be sent and can pass it to the module for transmission. This effectively provides a transparent communication link to an internet server from the application over GPRS. GBBA/SEM/BMS 03:0001 Rev A 47 GR47/GR48 Technical description 8 Technical Data Mechanical specifications Maximum length: 50 mm Maximum width: 33 mm Maximum thickness: 6.82 mm (without system connector pins length) Weight: 18,5 g Power supply voltage, normal operation Voltage: 3.6V Nominal Tolerance -0.2 +0.4V Ripple: <100mV @ 200KHz, <20mV @>200KHz Voltage must always stay within a normal operating range, ripple included. Power consumption: Speech mode < 250 mA (< 2 A peak) Idle mode: <5 mA Powered off: < 100 µA RTC accuracy: Max < 37ppm Typical < 20ppm Radio specifications Frequency range: GR 47: GSM 900 & EGSM 900 MHz and 1800 MHz (Dual Band) GR 48: GSM 850 MHz and 1900 MHz (Dual Band) Maximum RF output power: Antenna impedance: 2W/1W 50 Ω SIM card SIM card interface (external only) 3 V or 5 V Environmental specifications Operating temperature range: -25 0C to +55 0C Storage temperature range: -40 0C to +85 0C Maximum relative humidity: 95% at +40 0C Stationary vibration, sinusoidal: Displacement: 7.5 mm Acceleration amplitude: 20 m/s 2 m/s 2 Frequency range: 2-8 Hz 8-200 Hz 200-500 Hz Stationary vibration, random Acceleration spectral density (m2/s 2): 0.96 2.88 0.96 Frequency range: 5-10 10-200 200-500 60 min per/axis GBBA/SEM/BMS 03:0001 Rev A 40 48 GR47/GR48 Technical description Non-stationary vibration, including shock Shock response spectrum I, peak acceleration: - 3 shocks in each axis and direction: 300 m/s 2, 11 ms Shock response spectrum II, peak acceleration: - 3 shocks in each axis and direction: 1000 m/s 2, 6 ms Bump: Acceleration 250 m/s 2 Free fall transportation: 1.2 m Rolling pitching transportation: Angle: ±35 degrees, period: 8s Static load: 10 kPa Low air pressure/high air pressure: 70 kPa / 106 kPa Storage SMS Storage capacity 40 in ME In addition the unit can handle as many SMS as the SIM can store (SIM dependent). Phone book capacity 100 DAC Parameter Value Units Resolution 8 bit Output voltage swing for Code=00HEX 0.138 ± 0.1 V Output voltage swing for Code=FFHEX 2.61 ± 0.2 V Nominal Step Size 9.668 ± 0.1 mV Linear Code Range 8-247 (8H-F7H) LSB Absolute Error during Linear Range ±100 mV Conversion Speed <100 µs ADC Parameter Value Units Resolution 8 bit Input voltage for Code=00H 0.01 ± 0.01 V Input voltage for Code=FFH 2.75 ± 0.1 V Nominal Step Size 10.742 mV Accuracy ±3 LSB Input Impedance >1 MΩ Conversion Time to within 0.5bit <100 µs GBBA/SEM/BMS 03:0001 Rev A 49 GR47/GR48 Technical description 9 Contact details To contact customer support please use the details below. Customer Support Maplewood Building Chineham Business Park Basingstoke RG24 8YB E mail : [email protected] Or [email protected] GBBA/SEM/BMS 03:0001 Rev A 50