PRELIMINARY TECHNICAL DATA = Low Power, +2.3 V to +5.5 V, 50 MHz Complete DDS Preliminary Technical Data AD9834 Capability for phase modulation and frequency modulation is provided. Frequency accuracy can be controlled to one part in 0.25 billion. Modulation is effected by loading registers through the serial interface. FEATURES +2.3 V to +5.5 V Power Supply 50 MHz Speed Low Jitter Clock Output Sine Output/Triangular Output Serial Loading Power-Down Option Narrowband SFDR > 72 dB 20 mW Power Consumption at 3 V 20-Pin TSSOP The AD9834 offers the user a variety of output waveforms. The SIN ROM can be bypassed so that a linear up/down ramp is output from the DAC. If the SIN ROM is not by-passed, a sinusoidal output is available. Also, if a clock output is required, the MSB of the DAC data can be output, or the on-chip comparator can be used. APPLICATIONS Test Equipment Slow Sweep Generator DDS Tuning Digital Modulation The digital section is driven by an on-board regulator which steps down the applied DVDD to +2.5 V when DVDD exceeds +2.5 V. The analog and digital sections are independent and can be run from different power supplies e.g. AVDD can equals 5 V with DVDD equal to 3 V, etc. GENERAL DESCRIPTION The AD9834 is a numerically controlled oscillator employing a phase accumulator, a SIN ROM and a 10-bit D/A converter integrated on a single CMOS chip. Clock rates up to 50 MHz are supported with a power supply from 2.3 V to 5.5 V. The AD9834 has a power-down pin (SLEEP) which allows external control of a power-down mode. Sections of the device which are not being used can be powered down to minimise the current consumption e.g. the DAC can be powered down when a clock output is being generated. The part is available in a 20-pin TSSOP package. FUNCTIONAL BLOCK DIAGRAM AVDD AGND DGND MCLK DVDD CAP/2.5V REFOUT On-Board Reference Regulator FullScale Control VCC 2.5V FSELECT 28 Bit FREQ0 REG MUX FS ADJUST Phase Accumulator (28 Bit) 12 SIN ROM 10-Bit DAC MUX COMP IOUT IOUTB 28 Bit FREQ1 REG MSB MUX 12 Bit PHASE0 REG 12 Bit PHASE1 REG MUX DIV BY 2 MUX SIGN BIT OUT 16 Bit Control Register COMPARATOR Serial Interface & Control Logic FSYNC SCLK SDATA VIN AD9834 PSELECT SLEEP RESET REV PrM 04/02 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106,U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2002 PRELIMINARY TECHNICAL DATA AD9834 Ω; (VDD = +2.3 V to +5.5 V; AGND = DGND = 0 V; TA = TMIN to TMAX; RSET = 6.8 kΩ; RLOAD = 200 Ω for IOUT and IOUTB unless otherwise noted) SPECIFICATIONS1 Parameter Min SIGNAL DAC SPECIFICATIONS Resolution Update Rate (fMAX) IOUT Full Scale Output Compliance2 DC Accuracy: Integral Nonlinearity Differential Nonlinearity DDS SPECIFICATIONS Dynamic Specifications: Signal to Noise Ratio Total Harmonic Distortion Spurious Free Dynamic Range (SFDR): Wideband (0 to Nyquist) NarrowBand (± 200 kHz) Clock Feedthrough Wake Up Time Bits MSPS mA V 50 -53 50 72 –55 1 1 10 4 1 10 20 100 1.116 1.2 1 100 1.284 DVDD –0.9 DVDD - 0.5 2 0.9 0.5 1 10 IINH, Input Current CIN, Input Capacitance Low Power Sleep Mode4 50 2.8 0.8 Test Conditions/Comments LSB LSB VINL, Input Low Voltage POWER SUPPLIES AVDD DVDD I AA 4 I DD 4 IAA + IDD4 Units ±1 ±0.5 OUTPUT BUFFER Output Rise/Fall Time Output Jitter LOGIC INPUTS VINH, Input High Voltage Max 10 COMPARATOR Input Voltage Range Input Capacitance Input HighPass Cutoff Frequency Input DC Resistance Input DC Current VOLTAGE REFERENCE Internal Reference REFOUT Input Impedance3 Reference TC Typ dB dBc fMCLK = 50 MHz, fOUT = fMCLK/4096 fMCLK = 50 MHz, fOUT = fMCLK/4096 dBc dBc dBc ms fMCLK = 50 MHz, fOUT = fMCLK/7 fMCLK = 50 MHz, fOUT = fMCLK/7 V p-p pF MHz MΩ µA ac-coupled internally ns ps rms Using a 15 pF Load When DAC data MSB is output V KΩ ppm/°C 1.2 V ± 7% V V V V V µA pF +3.6 V to +5.5 V Power Supply +2.7 V to +3.6 V Power Supply +2.3 V to + 2.7 V Power Supply +3.6 V to +5.5 V Power Supply +2.3 V to + 3.6 V Power Supply fMCLK = 50 MHz, fOUT = fMCLK/7 2.3 2.3 5.5 5.5 5 0.5 + 0.04/MHz 7 10 0.25 10 15 V V mA mA mA mA mA 3 V Power Supply 5 V Power Supply DAC and Internal Clock Powered Down NOTES 1 Operating temperature range is as follows: B Version: –40°C to +85°C; typical specifications are at 25ⴗC 2 Guaranteed by Design. 3 Applies when REFOUT is sourcing current. The impedance is higher when REFOUT is sinking current. 4 Measured with the digital inputs static and equal to 0 V or DVDD. Specifications subject to change without notice. There is 95% test coverage of the digital circuitry. –2– REV PrM PRELIMINARY TECHNICAL DATA AD9834 RSET 6.8 K 100nF 10nF ON-BOARD REFERENCE REGULATOR FS ADJUST REFOUT CAP/2.5V 12 FULL-SCALE CONTROL SIN ROM 10-BIT DAC AVDD 10nF COMP IOUT 200R 20pF AD9834 Figure 1. Test Circuit With which Specifications are tested. TIMING CHARACTERISTICS1 (VDD = +2.3 V to +5.5 V; AGND = DGND = 0 V, unless otherwise noted) Parameter Limit at TMIN to TMAX Units Test Conditions/Comments t1 t2 t3 t4 t5 t6 t7 t8 20 8 8 25 10 10 5 10 t4 - 5 5 3 8 8 ns ns ns ns ns ns ns ns ns ns ns ns ns MCLK Period MCLK High Duration MCLK Low Duration SCLK Period SCLK High Duration SCLK Low Duration FSYNC to SCLK Falling Edge Setup Time FSYNC to SCLK Hold Time t9 t10 t11 t11A* min min min min min min min min max min min min min Data Setup Time Data Hold Time FSELECT, PSELECT Setup Time Before MCLK Rising Edge FSELECT, PSELECT Setup Time After MCLK Rising Edge 1 Guaranteed by design, not production tested. *See Pin Description Section. t1 MCLK MCLK t2 t 11A t 11 t3 FSELECT, PSELECT VALID DATA VALID DATA VALID DATA Figure 2. Master Clock Figure 3. Control Timing t5 t4 SCLK t7 t8 t6 FSYNC t10 t9 SDATA D15 D14 D2 D1 Figure 4. Serial Timing REV PrM –3– D0 D15 D14 PRELIMINARY TECHNICAL DATA AD9834 Storage Temperature Range . . . . . . . . . –65°C to +150°C Maximum Junction Temperature . . . . . . . . . . . . . +150°C TSSOP Package θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . 143°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . 45°C/W Lead Temperature, Soldering (10 sec) . . . . . . . . . 300°C IR Reflow, Peak Temperature . . . . . . . . . . . . . . . 220°C ABSOLUTE MAXIMUM RATINGS* (TA = +25°C unless otherwise noted) AVDD to AGND . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V DVDD to DGND . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V AVDD to DVDD . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V AGND to DGND. . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V CAP/2.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.75 V Digital I/O Voltage to DGND –0.3 V to DVDD + 0.3 V Analog I/O Voltage to AGND –0.3 V to AVDD + 0.3 V Operating Temperature Range Industrial (B Version) . . . . . . . . . . . . . . –40°C to +85°C *Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ORDERING GUIDE Model Temperature Range Package Description Package Option AD9834BRU EVAL-AD9834EB – 40°C to +85°C 20-Pin TSSOP (Thin Shrink Small Outline Package ) RU-20 Evaluation Board PIN CONFIGURATION FS ADJUST 1 REFOUT COMP 2 AVDD DVDD CAP/+2.5V 4 O 17 5 TOP VIEW (Not to Scale) 16 6 15 AGND VIN SIGNBITOUT FSYNC DGND MCLK 7 14 SCLK 8 13 SDATA FSELECT PSELECT 9 12 10 11 SLEEP RESET 20 AD9834 3 19 18 IOUTB IOUT CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9834 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –4– REV PrM PRELIMINARY TECHNICAL DATA AD9834 PIN FUNCTIONS DESCRIPTIONS Pin # Mnemonic Function ANALOG SIGNAL AND REFERENCE 1 FS ADJUST Full-Scale Adjust Control. A resistor (RSET) is connected between this pin and AGND. This determines the magnitude of the full-scale DAC current. The relationship between RSET and the full-scale current is as follows: IOUTFULL-SCALE = 18 x VREFOUT/RSET VREFOUT = 1.20 V nominal, RSET = 6.8 kΩ typical 2 REFOUT Voltage Reference Output. The AD9834 has an internal 1.20 V reference, which is made available at this pin. 3 COMP A DAC Bias Pin. This pin is used for de-coupling the DAC bias voltage. 17 VIN Input to comparator. The comparator can be used to generate a square wave from the sinusoidal DAC output. The DAC output should be filtered appropriately before being applied to the comparator to improve jitter. When bits OPBITEN and SIGNPIB in the control register are set to 1, the comparator input is connected to VIN. 19,20 IOUT, IOUTB Current Output. This is a high impedance current source. A load resistor of nominally 200 Ω should be connected between IOUT and AGND. IOUTB should preferably be tied through an external load resistor of 200 Ω to AGND but can be tied directly to AGND. A 20pF capacitor to AGND is also recommended to prevent clock feedthrough. POWER SUPPLY 4 AVDD Positive power supply for the analog section. AVDD can have a value from +2.3 V to +5.5 V. A 0.1 µF decoupling capacitor should be connected between AVDD and AGND. 5 DVDD Positive power supply for the digital section. DVDD can have a value from +2.3 V to +5.5 V. A 0.1 µF decoupling capacitor should be connected between DVDD and DGND. 6 CAP/2.5V The digital circuitry operates from a +2.5 V power supply. This +2.5 V is generated from DVDD using an on board regulator (when DVDD exceeds +2.7 V). The regulator requires a decoupling capacitor of typically 100 nF which is connected from CAP/2.5V to DGND. If DVDD is equal to or less than +2.7 V, CAP/2.5 V should be shorted to DVDD. 7 DGND Digital Ground. 18 AGND Analog Ground. DIGITAL INTERFACE AND CONTROL 8 MCLK Digital Clock Input. DDS output frequencies are expressed as a binary fraction of the frequency of MCLK. The output frequency accuracy and phase noise are determined by this clock. 9 FSELECT Frequency Select Input. FSELECT controls which frequency register, FREQ0 or FREQ1, is used in the phase accumulator. The frequency register to be used can be selected using the pin FSELECT or the bit FSEL. When the bit FSEL is being used to select the frequency register, this pin, FSELECT, should be tied to CMOS high or low. 10 PSELECT Phase Select Input. PSELECT controls which phase register, PHASE0 or PHASE1, is added to the phase accumulator output. The phase register to be used can be selected using the pin PSELECT or the bit PSEL. When the phase registers are being controlled by the bit PSEL, this pin, PSELECT, should be tied to CMOS high or low. 11 RESET Active high digital input. RESET resets appropriate internal registers to zero which corresponds to an analog output of midscale. RESET does not affect any of the addressable registers. 12 SLEEP Active high digital input. When this pin is high, the DAC is powered down. This pin has the same function as control bit SLEEP12. 13 SDATA Serial Data Input. The 16-bit serial data word is applied to this input. 14 SCLK Serial Clock Input. Data is clocked into the AD9834 on each falling SCLK edge. 15 FSYNC Active Low Control Input. This is the frame synchronisation signal for the input data. When FSYNC is taken low, the internal logic is informed that a new word is being loaded into the device. 16 SIGN BIT OUT Logic Output. The comparator output is available on this pin or, alternatively, the MSB from the NCO can be output on this pin. Setting bit OPBITEN in the control register to 1 enables this output pin. Bit SIGNPIB determines whether the comparator output or the MSB from the NCO is output on the pin. REV PrM –5– PRELIMINARY TECHNICAL DATA AD9834 Typical Performance Characteristics TPC 1. Typical Current Consumption vs. MCLK Frequency TPC 2. Narrow Band SFDR vs. MCLK Frequency TPC 3. Wide Band SFDR vs. MCLK Frequency TPC 4. Wide Band SFDR vs. fOUT/fMCLK for Various MCLK Frequencies TPC 5. SNR vs. MCLK Frequency TPC 6. SNR vs. fOUT/fMCLK for Various MCLK Frequencies TPC 7. Wake-Up Time vs. Temperature TPC 8. VREFOUT vs. Temperature –6– REV PrM PRELIMINARY TECHNICAL DATA AD9834 Typical Performance Characteristics TPC 9. fMCLK = 10 MHz; fOUT = 2.4 kHz; Frequency Word = 000FBA9 TPC 10. fMCLK = 10 MHz; fOUT = 1.43 kHz = fMCLK/7 ; Frequency Word = 2492492 TPC 11. fMCLK = 10 MHz; fOUT = 3.33 kHz = fMCLK/3 ; Frequency Word = 5555555 TPC 12. fMCLK = 50 MHz; fOUT = 12 kHz; Frequency Word = 000FBA9 TPC 13. fMCLK = 50 MHz; fOUT = 120 kHz; Frequency Word = 009D496 TPC 14. fMCLK = 50 MHz; fOUT = 1.2 MHz; Frequency Word = 0624DD3 TPC 15. fMCLK = 50 MHz; fOUT = 4.8 MHz; Frequency Word = 189374C TPC 16. fMCLK = 50 MHz; fOUT = 7.143 MHz = fMCLK/7 ; Frequency Word = 2492492 TPC 17. fMCLK = 50 MHz; fOUT = 16.667 MHz = fMCLK/3 ; Frequency Word = 5555555 REV PrM –7– PRELIMINARY TECHNICAL DATA AD9834 TERMINOLOGY THEORY OF OPERATION Integral Nonlinearity Sine waves are typically thought of in terms of their magnitude form a(t) = sin (ωt). However, these are nonlinear and not easy to generate except through piece wise construction. On the other hand, the angular information is linear in nature. That is, the phase angle rotates through a fixed angle for each unit of time. The angular rate depends on the frequency of the signal by the traditional rate of ω = 2πf. This is the maximum deviation of any code from a straight line passing through the endpoints of the transfer function. The endpoints of the transfer function are zero scale, a point 0.5 LSB below the first code transition (000 . . . 00 to 000 . . . 01) and full scale, a point 0.5 LSB above the last code transition (111 . . . 10 to 111 . . . 11). The error is expressed in LSBs. Differential Nonlinearity MAGNITUDE This is the difference between the measured and ideal 1 LSB change between two adjacent codes in the DAC. A specified differential nonlinearity of ±1 LSB maximium ensures +1 0 monotonicity. Output Compliance -1 The output compliance refers to the maximum voltage that can be generated at the output of the DAC to meet the specifications. When voltages greater than that specified for the output compliance are generated, the AD9834 may not meet the specifications listed in the data sheet. PHASE 2π 0 Spurious Free Dynamic Range Along with the frequency of interest, harmonics of the fundamental frequency and images of the these frequencies are present at the output of a DDS device. The spurious free dynamic range (SFDR) refers to the largest spur or harmonic which is present in the band of interest. The wide band SFDR gives the magnitude of the largest harmonic or spur relative to the magnitude of the fundamental frequency in the 0 to Nyquist bandwidth. The narrow band SFDR gives the attenuation of the largest spur or harmonic in a bandwidth of ±200 kHz about the fundamental frequency. Figure 5. Sine Wave Knowing that the phase of a sine wave is linear and given a reference interval (clock period), the phase rotation for that period can be determined. ∆Phase = ωδt Solving for ω ω = ∆Phase/δt = 2πf Solving for f and substituting the reference clock frequency for the reference period (1/fMCLK = δt) f = ∆Phase x fMCLK/2π Total Harmonic Distortion Total Harmonic Distortion (THD) is the ratio of the rms sum of harmonics to the rms value of the fundameltal. For the AD9834, THD is defined as: THD = 20 log√(V22 + V32 + V42 + V52 + V62)/V1 where V1 is the rms amplitude of the fundamental and V2, V3, V4, V5 and V6 are the rms amplitudes of the second through thre sixth harmonic. Signal-to-Noise Ratio (SNR) The AD9834 builds the output based on this simple equation. A simple DDS chip can implement this equation with three major subcircuits: Numerical Controlled Oscillator + Phase Modulator SIN ROM Digital- to- Analog Convertor. Each of these sub-circuits are discussed in the following section. S/N is the ratio of the rms value of the measured output signal to the rms sum of all other spectral components below the Nyquist frequency, excluding the first six harmonics and dc. The value for SNR is expressed in decibels. Clock Feedthrough There will be feedthrough from the MCLK input to the analog output. Clock feedthrough refers to the magnitude of the MCLK signal relative to the fundamental frequency in the AD9834’s output spectrum. –8– REV PrM PRELIMINARY TECHNICAL DATA AD9834 CIRCUIT DESCRIPTION The AD9834 is a fully integrated Direct Digital Synthesis (DDS) chip. The chip requires one reference clock, one low precision resistor and eight decoupling capacitors to provide digitally created sine waves up to 25 MHz. In addition to the generation of this RF signal, the chip is fully capable of a broad range of simple and complex modulation schemes. These modulation schemes are fully implemented in the digital domain allowing accurate and simple realization of complex modulation algorithms using DSP techniques. The internal circuitry of the AD9834 consists of the following main sections: a Numerical Controlled Oscillator (NCO), Frequency and Phase Modulators, SIN ROM, a Digital-to-Analog Converter, a Comparator and a Regulator. Numerical Controlled Oscillator + Phase Modulator This consists of two frequency select registers, a phase accumulator, two phase offset registers and a phase offset adder. The main component of the NCO is a 28-bit phase accumulator which assembles the phase component of the output signal. Continuous time signals have a phase range of 0 to 2. Outside this range of numbers, the sinusoid functions repeat themselves in a periodic manner. The digital implementation is no different. The accumulator simply scales the range of phase numbers into a multibit digital word. The phase accumulator in the AD9834 is implemented with 28 bits. Therefore, in the AD9834, 2 = 228. Likewise, the ∆Phase term is scaled into this range of numbers 0 < ∆Phase < 228 – 1. Making these substitutions into the equation above f = ∆Phase x fMCLK/228 where 0 < ∆Phase < 228 - 1. The input to the phase accumulator (i.e., the phase step) can be selected either from the FREQ0 Register or FREQ1 Register and this is controlled by the FSELECT pin or the FSEL bit. NCOs inherently generate continuous phase signals, thus avoiding any output discontinuity when switching between frequencies. Following the NCO, a phase offset can be added to perform phase modulation using the 12-bit Phase Registers. The contents of one of these phase registers is added to the most significant bits of the NCO. The AD9834 has two Phase registers, the resolution of these registers being 2π/4096. SIN ROM To make the output from the NCO useful, it must be converted from phase information into a sinusoidal value. Since phase information maps directly into amplitude, the SIN ROM uses the digital phase information as an address to a look-up table, and converts the phase information into amplitude. Although the NCO contains a 28-bit phase accumulator, the output of the NCO is truncated to 12 bits. Using the full resolution of the phase accumulator is impractical and unnecessary as this would require a look-up table of 228 entries. It is necessary only to have sufficient phase resolution such that the errors due to truncation are smaller than the resolution of the 10-bit REV PrM DAC. This requires the SIN ROM to have two bits of phase resolution more than the 10-bit DAC. The SIN ROM is enabled using bits MODE and OPBITEN in the control register. This is explained further in Table 14. Digital-to-Analog Converter The AD9834 includes a high impedance current source 10-bit DAC, capable of driving a wide range of loads. Full-scale output current can be adjusted, for optimum power and external load requirements, through the use of a single external resistor (RSET). The DAC can be configured for either single-ended or differential operation. IOUT and IOUTB can be connected through equal external resistors to AGND to develop complementary output voltages. The load resistors can be any value required, as long as the full-scale voltage developed across it does not exceed the voltage compliance range. Since full-scale current is controlled by RSET, adjustments to RSET can balance changes made to the load resistors. Comparator The AD9834 can be used to generate synthesised digital clock signals. This can be done by using the on-board self-biasing comparator, which converts the DAC's sinusoidal signal to a square wave. The output from the DAC may be filtered externally before being applied to the comparator input. The comparator reference voltage is the time-average of the signal applied to VIN. The comparator can accept a signal of 1 Vpp. As the comparator's input is ac-coupled, to operate correctly as a zero crossing dectector, it requires a minimum input frequency of 3 MHz. The comparator's output will be a square wave with an amplitude from 0 V to DVDD. To enable the comparator, bits SIGNPIB and OPBITEN in the control resister are set to '1'. This is explained further in Table 13. Regulator The AD9834 has separate power supplies for the analog and digital section. AVDD provides the power supply required for the analog section, while DVDD provides the power supply for the digital section. Both of these supplies can have a value of +2.3V to +5.5V, and are independant of each other e.g. the analog section can be operated at 5V and the digital section can be operated at 3V or vice versa. The internal digital section of the AD9834 is operated at 2.5 V. An on-board regulator steps down the voltage applied at DVDD to 2.5 V. The digital inteface (serial port) of the AD9834 is also operated from DVDD. These digital signals are level shifted within the AD9834 to make them 2.5V compatible. When the applied voltage at the DVDD pin of the AD9834 is equal to or less than 2.5V, the pins CAP/2.5V and DVDD should be tied together, thus by-passing the on-board regulator. –9– PRELIMINARY TECHNICAL DATA AD9834 FUNCTIONAL DESCRIPTION Serial Interface The AD9834 has a standard 3-wire serial interface, which is compatible with SPI, QSPI, MICROWIRE and DSP interface standards. Data is loaded into the device as a 16-bit word under the control of a serial clock input, SCLK. The timing diagram for this operation is given in Figure 4. The FSYNC input is a level triggered input that acts as a frame synchronisation and chip enable. Data can only be transferred into the device when FSYNC is low. To start the serial data transfer, FSYNC should be taken low, observing the minimum FSYNC to SCLK falling edge setup time, t7. After FSYNC goes low, serial data will be shifted into the device's input shift register on the falling edges of SCLK for 16 clock pulses. FSYNC may be taken high after the sixteenth falling edge of SCLK, observing the minimum SCLK falling edge to FSYNC rising edge time, t8. Alternatively, FSYNC can be kept low for a multiple of 16 SCLK pulses, and then brought high at the end of the data transfer. In this way, a continuous stream of 16 bit words can be loaded while FSYNC is held low, FSYNC only going high after the 16th SCLK falling edge of the last word loaded. The SCLK can be continuous or, alternatively, the SCLK can idle high or low between write operations. Powering up the AD9834 The flow chart in Figure 7 shows the operating routine for the AD9834. When the AD9834 is powered up, the part should be reset. This will reset appropriate internal registers to zero to provide an analog output of midscale. To avoid spurious DAC outputs while the AD9834 is being initialized, the RESET bit/pin should be set to 1 until the part is ready to begin generating an output. RESET does not reset the phase, frequency or control registers. These registers will contain invalid data and, therefore, should be set to a known value by the user. The RESET bit/pin should then be set to 0 to begin generating an output. A signal will appear at the DAC output 7 MCLK cycles after RESET is set to 0. Latency Associated with each operation is a latency. When the pins FSELECT and PSELECT change value there is a pipeline delay before control is transfered to the selected register. When the timing specifications t11 and t11A are met (see figure 3) FSELECT and PSELECT have latencies of 7 MCLK cycles. When the timing specifications t11 and t11A are not met, the latency is increased by one MCLK cycle. Similarly there is a latency associated with each asynchronous write operation. If a selected frequency/phase register is loaded with a new word there is a delay of 7 to 8 MCLK cycles before the analog output will change. (There is an uncertainty of one MCLK cycle as it depends on the position of the MCLK rising edge when the data is loaded into the destination register.) The negative transition of the RESET and SLEEP functions are sampled on the internal falling edge of MCLK, therefore also have a latency associated with them. The Control Register The AD9834 contains a 16-bit control register which sets up the AD9834 as the user wishes to operate it. All control bits, except MODE, are sampled on the internal negative edge of MCLK. Table 2, on the following page, describes the individual bits of the control register. The different functions and the various output options from the AD9834 are described in more detail in the section following Table 2. To inform the AD9834 that you wish to alter the contents of the Control register, D15 and D14 must be set to '0' as shown below. Table 1. Control Register D15 D14 0 0 D13 D0 CONTROL BITS SLEEP12 AD9834 SLEEP1 SIN ROM Phase Accumulator (28 Bit) 0 MUX 1 (Low Power) IOUT 10 - Bit DAC IOUTB COMPARATOR MODE + OPBITEN Div by 2 1 MUX 0 1 MUX 0 VIN DIGITAL OUTPUT SIGN BIT OUT (enable) DIV2 SIGNPIB OPBITEN Figure 6. Function of Control Bits –10– REV PrM PRELIMINARY TECHNICAL DATA AD9834 Table 2. Description of bits in the Control Register Bit Name Function D13 B28 D12 HLB D11 FSEL D10 PSEL D9 PIN/SW D8 RESET D7 SLEEP1 D6 SLEEP12 D5 OPBITEN D4 SIGNPIB D3 DIV2 D2 D1 Reserved MODE D0 Reserved Two write operations are required to load a complete word into either of the Frequency registers. B28 = '1' allows a complete word to be loaded into a frequency register in two consecutive writes. The first write contains the 14 LSBs of the frequency word and the next write will contain the 14 MSBs. The first two bits of each sixteen-bit word define the frequency register to which the word is loaded, and should therefore be the same for both of the consecutive writes. Refer to table 6 for the appropriate addresses. The write to the frequency register occurs after both words have been loaded, so the register never holds an intermediate value. An example of a complete 28-bit write is shown in table 7. When B28 = '0' the 28-bit frequency register operates as 2 14-bit registers, one containing the 14 MSBs and the other containing the 14 LSBs. This means that the 14 MSBs of the frequency word can be altered independent of the 14 LSBs and vice versa. To alter the 14 MSBs or the 14 LSBs, a single write is made to the appropriate Frequency address. The control bit D12 (HLB) informs the AD9834 whether the bits to be altered are the 14 MSBs or 14 LSBs. This control bit allows the user to continuously load the MSBs or LSBs of a frequency regiser while ignoring the remaining 14 bits. This is useful if the complete 28 bit resolution is not required. HLB is used in conjunction with D13 (B28). This control bit indicates whether the 14 bits being loaded are being transferred to the 14 MSBs or 14 LSBs of the addressed frequency register. D13 (B28) must be set to '0' to be able to change the MSBs and LSBs of a frequency word seperately. When D13 (B28) = '1', this control bit is ignored. HLB = '1' allows a write to the 14 MSBs of the addressed frequency register. HLB = '0' allows a write to the 14 LSBs of the addressed frequency register. The FSEL bit defines whether the FREQ0 register or the FREQ1 register is used in the phase accumulator. See table 4 on selecting a frequency register. The PSEL bit defines whether the PHASE0 register or the PHASE1 register data is added to the output of the phase accumulator. See Table 5 on selecting a phase register. Functions that select frequency and phase registers, reset internal registers, and power down the DAC can be implemented using either software or hardware. PIN/SW selects the source of control for these functions. PIN/SW = '1' implies that the functions are being controlled using the appropriate control pins. PIN/SW = '0' implies that the functions are being controlled using the appropriate control bits. RESET = '1' resets internal registers to zero, which corresponds to an analog output of midscale. RESET = '0' disables Reset. This function is explained further in Table 11. When SLEEP1 = '1', the internal MCLK clock is disabled. The DAC output will remain at its present value as the NCO is no longer accumulating. When SLEEP1 = '0' MCLK is enabled. This function is explained further in Table 12. SLEEP12 = '1' powers down the on-chip DAC. This is useful when the AD9834 is used to output the MSB of the DAC data. SLEEP12 = '0' implies that the DAC is active. This function is explained further in Table 12. The function of this bit is to control whether there is an output at the pin SIGN BIT OUT. This bit should remain at '0' if the user is not using the pin SIGN BIT OUT. OPBITEN = '1' enables the pin SIGN BIT OUT. When OPBITEN equals 0, the SIGN BIT OUT output buffer is put into a high impedance state and, therefore, no output is available at the SIGN BIT OUT pin. The function of this bit is to control what is output at the pin SIGN BIT OUT. When SIGNPIB = '1', the on board comparator is connected to SIGN BIT OUT. After filtering the sinusoidal output from the DAC, the waveform can be applied to the comparator to generate a square waveform. This is explained futher in Table 13. When SIGNPIB = '0', the MSB (or MSB/2) of the DAC data is connected to the pin SIGN BIT OUT. The bit DIV2 controls whether it is the MSB or MSB/2 that is ouput. DIV2 is used in association with SIGNPIB and OPBITEN. This is fully explained in Table 13. When DIV2 = '1', the digital output is passed directly to the SIGN BIT OUT pin. When DIV2 = '0', the digital output/2 is passed directly to the SIGN BIT OUT pin. This bit must always be set to 0. The function of this bit is to control what is output at the IOUT/IOUT pins. This bit should be set to '0' if the control bit OPBITEN = '1'. When MODE = '1', the SIN ROM is bypassed, resulting in a ramp output from the DAC. When MODE = '0' the SIN ROM is used to convert the phase information into amplitude information which results in a sinusoidal signal at the output (See table 14). This bit must always be set to 0. REV PrM –11– PRELIMINARY TECHNICAL DATA AD9834 The Frequency and Phase Resisters The AD9834 contains 2 frequency registers and 2 phase registers. These are described in Table 3 below. Table 3. Frequency/Phase Registers Register Size FREQ0 28 Bits Frequency Register 0. When FSEL bit or FSELECT pin = 0, this register defines the output frequency as a fraction of the MCLK frequency. 28 Bits Frequency Register 1. When FSEL bit or FSELECT pin = 1, this register defines the output frequency as a fraction of the MCLK frequency. 12 Bits Phase Offset Register 0. When PSEL bit or PSELECT pin = 0, the contents of this register are added to the output of the phase accumulator. 12 Bits Phase Offset Register 1. When PSEL bit or PSELECT pin = 1, the contents of this register are added to the output of the phase accumulator. FREQ1 PHASE0 PHASE1 Description The analog output from the AD9834 is fMCLK/228 x FREQREG where FREQREG is the value loaded into the selected frequency register. This signal will be phase shifted by 2π/4096 x PHASEREG where PHASEREG is the value contained in the selected phase register. Access to the frequency and phase registers is controlled by both the FSELECT/PSELECT pins and the FSEL/ PSEL control bits. If the control bit PIN/SW = 1, the pins controls the function, whereas if PIN/SW = 0, the bits control the function. This is outlined in tables 4 and 5 below. If the FSEL/PSEL bits are being used, the pins should preferably be held at CMOS logic high or low. Control of the frequency/phase registers can be interchanged from the pins to the bits. Table 4: Selecting a Frequency Register FSELECT 0 1 X X FSEL X X 0 1 PIN/SW 1 1 0 0 Selected Register FREQ0 REG FREQ1 REG FREQ0 REG FREQ1 REG Table 5: Selecting a Phase Register PSELECT 0 1 X X PSEL X X 0 1 PIN/SW 1 1 0 0 The FSELECT and PSELECT pins are sampled on the internal falling edge of MCLK. It is recommended that the data on these pins does not change within a time window of the falling edge of MCLK (see Figure 3 for timing). If FSELECT/PSELECT changes value when a falling edge occurs, there is an uncertainty of one MCLK cycle as to when control is transferred to the other frequency/phase register. The flow charts in Figures 8 and 9 show the routine for selecting and writing to the frequency and phase registers of the AD9834. Writing to a Frequency Register: When writing to a frequency register, bits D15 and D14 give the address of the frequency register. Table 6. Frequency Register Bits D15 D14 D13 0 1 1 0 MSB MSB D0 14 FREQ0 REG BITS 14 FREQ1 REG BITS LSB LSB If the user wishes to alter the entire contents of a frequency register, two consecutive writes to the same address must be performed, as the frequency registers are 28 bits wide. The first write will contain the 14 LSBs while the second write will contain the 14 MSBs. For this mode of operation, the control bit B28 (D13) should be set to 1. An example of a 28-bit write is shown in Table 7 below. Table 7: Writing 3FFF0000 to FREQ0 REG SDATA input Result of input word 0010 0000 0000 0000 Control word write (D15, D14 = 00); B28 (D13) = 1; HLB (D12) = X FREQ0 REG write (D15, D14 = 01); 14 LSBs = 0000 FREQ0 REG write (D15, D14 = 01); 14 MSBs = 3FFF 0100 0000 0000 0000 0111 1111 1111 1111 In some applications, the user does not need to alter all 28 bits of the frequency register. With coarse tuning, only the 14 MSBs are altered while with fine tuning, only the 14 LSBs are altered. By setting the control bit B28 (D13) to 0, the 28-bit frequency register operates as 2 14-bit registers, one containing the 14 MSBs and the other containing the 14 LSBs. This means that the 14 MSBs of the frequency word can be altered independent of the 14 LSBs and vice versa. Bit HLB (D12) in the control register identifies which 14 bits are being altered. Examples of this are shown over. Selected Register PHASE0 REG PHASE1 REG PHASE0 REG PHASE1 REG –12– REV PrM PRELIMINARY TECHNICAL DATA AD9834 Table 8: Writing 3FFF to the 14 LSBs of FREQ1 REG SDATA input Result of input word 0000 0000 0000 0000 1011 1111 1111 1111 Control word write (D15, D14 = 00); B28 (D13) = 0; HLB (D12) = 0, i.e. LSBs FREQ1 REG write (D15, D14 = 10); 14 LSBs = 3FFF The Sleep Function Sections of the AD9834 which are not in use can be powered down minimise power consumption. This is done using the Sleep Function. The parts of the chip that can be powered down are the Internal clock and the DAC. The DAC can be powered down through hardware or software. The pin/bits required for the Sleep Function are outlined in Table 12. Table 9: Writing 3FFF to the 14 MSBs of FREQ0 REG SDATA input Result of Input word 0001 0000 0000 0000 0111 1111 1111 1111 Control word write (D15, D14 = 00); B28 (D13) = 0; HLB (D12) = 1, i.e. MSBs FREQ0 REG write (D15, D14 = 01); 14 MSBs = 3FFF Writing to a Phase Register: When writing to a phase register, bits D15 and D14 are set to 11. Bit D13 identifies which phase register is being loaded. Table 10. Phase Register Bits D15 D14 1 1 1 1 D13 D12 D11 0 1 X X MSB MSB D0 12 PHASE0 BITS 12 PHASE1 BITS LSB LSB The RESET Function The RESET function resets appropriate internal registers to zero to provide an analog output of midscale. RESET does not reset the phase, frequency or control registers. When the AD9834 is powered up, the part should be reset. To reset the AD9834, set the RESET pin/bit to 1. To take the part out of reset, set the pin/bit to 0. A signal will appear at the DAC output 7 MCLK cycles after RESET is set to 0. The RESET function is controlled by both the RESET pin and the RESET control bit. If the control bit PIN/SW = 0, the RESET bit controls the function, whereas if PIN/ SW = 1, the pin control the function. Table 12: Applying the SLEEP Function SLEEP SLEEP1 SLEEP12 pin bit bit 0 1 X X X X X X 0 0 1 1 X X 0 1 0 1 PIN/SW bit 1 1 0 0 0 0 Result No powerdown DAC Powered Down No powerdown DAC Powered Down Internal Clock disabled Both the DAC powered down and the Internal Clock disabled DAC Powered Down: This is useful when the AD9834 is used to output the MSB of the DAC data only. In this case, the DAC is not required so it can be powered down to reduce power consumption. Internal Clock disabled: When the internal clock of the AD9834 is disabled the DAC output will remain at its present value as the NCO is no longer accumulating. New frequency, phase and control words can be written to the part when the SLEEP1 control bit is active. The synchronising clock is still active which means that the selected frequency and phase registers can also be changed either at the pins or by using the control bits. Setting the SLEEP1 bit equal to 0 enables the MCLK. Any changes made to the registers while SLEEP1 was active will be seen at the output after a certain latency. The effect of asserting the SLEEP pin is seen immediately at the output, i.e. the zero to one transition of this pin is not sampled. However, the negative transition of SLEEP is sampled on the internal falling edge of MCLK. The SIGN BIT OUT Pin Table 11: Applying RESET RESET pin 0 1 X X RESET bit X X 0 1 PIN/SW 1 1 0 0 Result No Reset Applied Internal Registers Reset No Reset Applied Internal Registers Reset The effect of asserting the RESET pin is seen immediately at the output, i.e. the zero to one transition of this pin is not sampled. However, the negative transition of RESET is sampled on the internal falling edge of MCLK. REV PrM The AD9834 offers a variety of outputs from the chip. The digital outputs are available from the SIGN BIT OUT pin. The available outputs are the comparator output or the MSB of the DAC data. This pin must be enabled before use. The enabling/disabling of this pin is controlled by the bit OPBITEN (D5) in the control register. When OPBITEN = 1, this pin is enabled. Note that the MODE bit (D1) in the control register should be set to '0' if OPBITEN = '1'. –13– PRELIMINARY TECHNICAL DATA AD9834 Comparator Output: The AD9834 has an on-board comparator. To connect this comparator to the SIGN BIT OUT pin, the SIGNPIB (D4) control bit must be set to 1. After filtering the sinusoidal output from the DAC, the waveform can be applied to the comparator to generate a square waveform. MSB from the NCO: The MSB from the NCO can be output from the AD9834. By setting the SIGNPIB (D4) control bit to 0, the MSB of the DAC data is available at the SIGN BIT OUT pin. This is useful as a coarse clock source. This square wave can also be divided by 2 before being output. The bit DIV2 (D3) in the control register controls the frequency of this output from the SIGN BIT OUT pin. Table 13: Various Outputs from SIGN BIT OUT OPBITEN MODE Bit Bit 0 1 1 1 1 1 SIGNPIB DIV2 Bit Bit X 0 0 0 0 1 X 0 0 1 1 X X 0 1 0 1 X SIGN BIT OUT Pin High Impedance DAC data MSB / 2 DAC data MSB Reserved Comparator Output Reserved APPLICATIONS Because of the various output options available from the part, the AD9834 can be configured to suit a wide variety of applications. One of the areas where the AD9834 is suitable is in modulation applications. The part can be used to perform simple modulation such as FSK. More complex modulation schemes such as GMSK and QPSK can also be implemented using the AD9834. In an FSK application, the two frequency registers of the AD9834 are loaded with different values; one frequency will represent the space frequency while the other will represent the mark frequency. The digital data stream is fed to the FSELECT pin which will cause the AD9834 to modulate the carrier frequency between the two values. The AD9834 has two phase registers; this enables the part to perform PSK. With phase shift keying, the carrier frequency is phase shifted, the phase being altered by an amount which is related to the bit stream being input to the modulator. The AD9834 is also suitable for signal generator applications. With the on-board comparator, the device can be used to generate a square wave. With its low current consumption, the part is suitable for applications in which it can be used as a local oscillator. The IOUT/IOUTB Pins The analog outputs from the AD9834 are available from the IOUT/IOUTB pins. The available outputs are a sinuoidal output or a ramp output. Sinusoidal Output: The SIN ROM is used to convert the phase information from the frequency and phase registers into amplitude information which results in a sinusoidal signal at the output. To have a sinusoidal output from the IOUT/IOUTB pins set the bt MODE (D1) = 1. Up/Down Ramp Output: The SIN ROM can be bypassed so that the truncated digital output from the NCO is sent to the DAC. In this case, the output is no longer sinusoidal. The DAC will produce a ramp up/down function. To have a ramp output from the IOUT/IOUTB pins set the bt MODE (D1) = 0. Note that the SLEEP pin/SLEEP12 bit must be 0 (i.e. the DAC is enabled) when using these pins. Table 14: Various Outputs from IOUT/IOUTB OPBITEN Bit 0 0 1 1 MODE Bit IOUT / IOUTB Pins 0 1 0 1 Sinusoid Up/Down Ramp Sinusoid Reserved –14– REV PrM PRELIMINARY TECHNICAL DATA AD9834 DATA WRITE See Figure 9 SELECT DATA SOURCES See Figure 10 INITIALISATION See Figure 8 below WAIT 7/8 MCLK CYCLES See Timing Diagram Fig. 2 DAC OUTPUT VOUT = VREFOUT * 18 * RLOAD/RSET * (1+ (SIN(2p(FREQREG * FMCLK * t/228 + PHASEREG/212))) YES CHANGE PHASE? CHANGE PSEL/ YES PSELECT? NO NO YES CHANGE FSEL/ YES CHANGE FREQUENCY? FSELECT? NO CHANGE DAC OUTPUT FROM SIN TO RAMP? YES CONTROL REGISTER WRTE? YES NO CHANGE FREQ REGISTER? YES CHANGE PHASE REGISTER? NO YES CHANGE OUTPUT AT SIGN BIT OUT PIN? NO Figure 7. Flow Chart for AD9834 Initialisation and Operation INITIALISATION APPLY RESET USING CONTROL BIT USING PIN (CONTROL REGISTER WRITE) (CONTROL REGISTER WRITE) RESET = 1 PIN/SW = 0 PIN/SW = 1 WRITE TO FREQUENCY AND PHASE REGISTERS FREQ0 REG = FOUT0 / fMCLK * 228 FREQ1 REG = FOUT1 / fMCLK * 228 PHASE 0 & PHASE1 REG = (PhaseShift * 212) / 2p (See Figure 9 Below) SET RESET = 0 SELECT FREQUENCY REGISTERS SELECT PHASE REGISTERS USING CONTROL BIT USING PIN (CONTROL REGISTER WRITE) (APPLY SIGNALS AT PINS) RESET bit = 0 FSEL = Selected Freq Register PSEL = Selected Phase Register PIN/SW = 0 RESET pin = 0 FSELECT = Selected Freq Register PSELECT = Selected Phase Register Figure 8. Initialisation REV PrM –15– SET RESET PIN = 1 PRELIMINARY TECHNICAL DATA AD9834 DATA WRITE NO WRITE A FULL 28-BIT WORD TO A FREQUENCY REGISTER? NO WRITE TO PHASE REGISTER? WRITE 14 MSBs OR LSBs TO A FREQUENCY REGISTER? YES YES YES (CONTROL REGISTER WRITE) (CONTROL REGISTER WRITE) B28 (D13) = 0 HLB (D12) = 0 / 1 B28 (D13) = 1 YES WRITE 2 CONSECUTIVE 16-BIT WORDS WRITE A 16-BIT WORD (See Table 7 for Example) (See Tables 8 & 9 for examples) WRITE 14 MSBs OR LSBs TO A FREQUENCY REGISTER? WRITE ANOTHER FULL 28 BITS TO A FREQUENCY REGISTER? (16 - Bit Write) D15, D14 = 11 D13 = 0/1 (chooses the phase register) D12 = X D11 ... D0 = Phase Data WRITE TO ANOTHER PHASE REGISTER? YES YES NO NO NO Figure 9. Data Writes SELECT DATA SOURCES YES FSELECT AND PSELECT PINS BEING USED? SET FSELECT AND PSELECT NO (CONTROL REGISTER WRITE) (CONTROL REGISTER WRITE) PIN/SW = 0 SET FSEL Bit SET PSEL Bit PIN/SW = 1 Figure 10. Selecting Data Sources –16– REV PrM PRELIMINARY TECHNICAL DATA AD9834 GROUNDING AND LAYOUT INTERFACING TO MICROPROCESSORS The printed circuit board that houses the AD9834 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of ground planes which can be separated easily. A minimum etch technique is generally best for ground planes as it gives the best shielding. Digital and analog ground planes should only be joined in one place. If the AD9834 is the only device requiring an AGND to DGND connection, then the ground planes should be connected at the AGND and DGND pins of the AD9834. If the AD9834 is in a system where multiple devices require AGND to DGND connections, the connection should be made at one point only, a star ground point that should be established as close as possible to the AD9834. The AD9834 has a standard serial interface which allows the part to interface directly with several microprocessors. The device uses an external serial clock to write the data/ control information into the device. The serial clock can have a frequency of 40 MHz maximum. The serial clock can be continuous or, it can idle high or low between write operations. When data/control information is being written to the AD9834, FSYNC is taken low and is held low while the 16 bits of data are being written into the AD9834. The FSYNC signal frames the 16 bits of information being loaded into the AD9834. Avoid running digital lines under the device as these will couple noise onto the die. The analog ground plane should be allowed to run under the AD9834 to avoid noise coupling. The power supply lines to the AD9834 should use as large a track as is possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other sections of the board. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This will reduce the effects of feedthrough through the board. A microstrip technique is by far the best but is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground planes while signals are placed on the other side. Good decoupling is important. The analog and digital supplies to the AD9834 are independent and separately pinned out to minimize coupling between analog and digital sections of the device. All analog and digital supplies should be decoupled to AGND and DGND respectively with 0.1 µF ceramic capacitors in parallel with 10 µF tantalum capacitors. To achieve the best from the decoupling capacitors, they should be placed as close as possible to the device, ideally right up against the device. In systems where a common supply is used to drive both the AVDD and DVDD of the AD9834, it is recommended that the system’s AVDD supply be used. This supply should have the recommended analog supply decoupling between the AVDD pins of the AD9834 and AGND and the recommended digital supply decoupling capacitors between the DVDD pins and DGND. REV PrM AD9834 to ADSP-21xx Interface Figure 12 shows the serial interface between the AD9834 and the ADSP-21xx. The ADSP-21xx should be set up to operate in the SPORT Transmit Alternate Framing Mode (TFSW = 1). The ADSP-21xx is programmed through the SPORT control register and should be configured as follows: Internal clock operation (ISCLK = 1) Active low framing (INVTFS = 1) 16-bit word length (SLEN = 15) Internal frame sync signal (ITFS = 1) Generate a frame sync for each write (TFSR = 1). Transmission is initiated by writing a word to the Tx register after the SPORT has been enabled. The data is clocked out on each rising edge of the serial clock and clocked into the AD9834 on the SCLK falling edge. Figure 11. ADSP2101/ADSP2103 to AD9834 Interface AD9834 to 68HC11/68L11 Interface Figure 13 shows the serial interface between the AD9834 and the 68HC11/68L11 microcontroller. The microcontroller is configured as the master by setting bit MSTR in the SPCR to 1 and, this provides a serial clock on SCK while the MOSI output drives the serial data line SDATA. Since the microcontroller does not have a dedicated frame sync pin, the FSYNC signal is derived from a port line (PC7). The set up conditions for correct operation of the interface are as follows: SCK idles high between write operations (CPOL = 0) data is valid on the SCK falling edge (CPHA = 1). When data is being transmitted to the AD9834, the FSYNC line is taken low (PC7). Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes with only 8 falling clock edges occuring in the transmit cycle. Data is transmitted MSB first. In order to load data into the AD9834, PC7 is held low after the first 8 bits are transferred and a second serial write operation is performed to the AD9834. Only after the second 8 bits have been trans- –17– PRELIMINARY TECHNICAL DATA AD9834 ferred should FSYNC be taken high again. being applied to the AD9834. The interface to the DSP56000/DSP56001 is similar to that of the DSP56002. Figure 12. 68HC11/68L11 to AD9834 Interface AD9834 to 80C51/80L51 Interface Figure 14 shows the serial interface between the AD9834 and the 80C51/80L51 microcontroller. The microcontroller is operated in mode 0 so that TXD of the 80C51/80L51 drives SCLK of the AD9834 while RXD drives the serial data line SDATA. The FSYNC signal is again derived from a bit programmable pin on the port (P3.3 being used in the diagram). When data is to be transmitted to the AD9834, P3.3 is taken low. The 80C51/80L51 transmits data in 8 bit bytes thus, only 8 falling SCLK edges occur in each cycle. To load the remaining 8 bits to the AD9834, P3.3 is held low after the first 8 bits have been transmitted and a second write operation is initiated to transmit the second byte of data. P3.3 is taken high following the completion of the second write operation. SCLK should idle high between the two write operations. The 80C51/80L51 outputs the serial data in a format which has the LSB first. The AD9834 accepts the MSB first (the 4 MSBs being the control information, the next 4 bits being the address while the 8 LSBs contain the data when writing to a destination register). Therefore, the transmit routine of the 80C51/80L51 must take this into account and re-arrange the bits so that the MSB is output first. Figure 14. AD9834 to DSP56002 Interface AD9834 EVALUATION BOARD The AD9834 Evaluation Board allows designers to evaluate the high performance AD9834 DDS modulator with minimum of effort. To prove that this device will meet the user's waveform synthesis requirements, the user only require's a powersupply, an IBM-compatible PC and a spectrum analyser along with the evaluation board. The DDS evaluation kit includes a populated, tested AD9834 printed circuit board. The evaluation board interfaces to the parallel port of an IBM compatible PC. Software is available with the evaluation board which allows the user to easily program the AD9834. A schematic of the Evaluation board is shown in Figure 24. The software will run on any IBM compatible PC which has Microsoft Windows95, Windows98 or Windows ME 2000 NT™ installed. Using the AD9834 Evaluation Board The AD9834 Evaluation kit is a test system designed to simplify the evaluation of the AD9834. An application note is also available with the evaluation board and gives full information on operating the evaluation board. Prototyping Area Figure 13. 80C51/80L51 to AD9834 Interface AD9834 to DSP56002 Interface Figure 15 shows the interface between the AD9834 and the DSP56002. The DSP56002 is configured for normal mode asynchronous operation with a Gated internal clock (SYN = 0, GCK = 1, SCKD = 1). The frame sync pin is generated internally (SC2 = 1), the transfers are 16 bits wide (WL1 = 1, WL0 = 0) and the frame sync signal will frame the 16 bits (FSL = 0). The frame sync signal is available on pin SC2 but, it needs to be inverted before An area is available on the evaluation board for the user to add additional circuits to the evaluation test set. Users may want to build custom analog filters for the output or add buffers and operational amplifiers to be used in the final application. XO vs. External Clock The AD9834 can operate with master clocks up to 50MHz. A 50MHz oscillator is included on the evaluation board. However, this oscillator can be removed and, if required, an external CMOS clock connected to the part. Power Supply Power to the AD9834 Evaluation Board must be provided externally through pin connections. The power leads should be twisted to reduce ground loops. –18– REV PrM PRELIMINARY TECHNICAL DATA AD9834 DVDD AVDD C1 0.1µ F C13 0.01µ F 1 2 3 4 5 6 SCLK SDATA FSYNC LK4 AVDD 6 DVDD 4 5 DVDD AVDD C14 0.01µ F CAP C6 0.1µ F J1 COMP 1 7 8 SCLK 9 10 SDATA FSYNC 11 12 13 14 C2 0.1µ F RESET 2 18 14 SCLK 4 16 13 SDATA 6 14 15 FSYNC 8 12 11 REFOUT SLEEP FSADJUST R1 10K 17 18 19 20 21 IOUTB IOUT PSELECT LK1 10 9 FSELECT LK2 22 23 24 25 26 27 U1 AD9834 U2 R2 10K 2 DVDD C4 0.1µ F LK5 12 1 R4 6.8k RESET RESET 15 16 C3 10nF 3 20 C11 IOUTB 19 R5 200R PSELECT VIN 17 FSELECT C12 R6 IOUT 200R R7 C11 300R C11 8 MCLK DVDD SW SIGNBITOUT DGND 16 SBOUT AGND 7 18 DVDD J2 J3 AVDD 28 29 30 31 32 33 34 35 36 C8 10µF MCLK C7 0.1µ F C9 0.1µ F C10 10µF LK3 DVDD R3 50R 14 C5 0.1µ F DVDD U3 OUT 8 DGND 7 Figure 15. AD9834 Evaluation Board Layout Integrated Circuits U3 OSC XTAL 50 MHz U1 AD9834BRU U2 74HCT244 Links Lk1 Lk2 Lk5 Lk3 Lk4 3 pin sil header 2 pin sil header Switch Capacitors C1 C2 C5 C6 C7 C9 C14 C3 C4 C13 C8 C10 C11 C12 C15 C16 Resistors R1 R2 R3 R4 R5 R6 R7 REV PrM 100nF Ceramic Capacitor 10nF ceramic Capacitor 10uF Tantalum Capacitor Option for extra decoupling capacitors 10 KΩ Resistor 51 Ω Resistor 6.8 kΩ Resistor 200 Ω Resistor 300 Ω Resistor SW Sockets PSEL1; FSEL1; IOUT; IOUTB; Connectors J1 J2, J3 –19– End Stackable Switch (SDC Double Throw) CLK1; Sub Minature BNC SBOUT; Connector 36-Pin Edge Connector PCB Mounting Terminal Block PRELIMINARY TECHNICAL DATA AD9834 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 20-Lead Small Outline Package (TSSOP) (RU-20) 0.260 (6.60) 0.252 (6.40) 20 0.256 (6.50) 0.246 (6.25) 0.177 (4.50) 0.169 (4.30) 11 1 0.006 (0.15) 0.002 (0.05) SEATING PLANE 10 PIN 1 0.0256 (0.65) BSC 0.0118 (0.30) 0.0075 (0.19) –20– 0.0433 (1.10) MAX 0.0079 (0.20) 0.0035 (0.090) 8o 0o 0.028 (0.70) 0.020 (0.50) REV PrM