E-X(S)D-1W&F-X(S)D-1W Series Isolated 1W Dual&Single Output DC/DC Converters SELECTION GUIDE Input Output Voltage Output Current Input Current Voltage (V) (V) (MA) (MA) F0505XD-1W 5 5 200 F0509XD-1W 5 9 111 F0512XD-1W 5 12 F0515XD-1W 5 ◆Efficiency up to 79% F0505XS-1W ◆Power density up to 0.85W/cm3 Isolationt MTTF1 (KHRS) Efficiency (%) Capacitance 294 68 23 4241 267 75 30 3376 84 260 77 26 2555 15 67 256 78 27 1838 5 5 200 294 68 23 4241 F0509XS-1W 5 9 111 267 75 30 3376 F0512XS-1W 5 12 84 260 77 26 2555 F0515XS-1W 5 15 67 256 78 27 1838 F1205XD-1W 12 5 200 121 69 26 2664 F1209XD-1W 12 9 111 113 74 35 2295 F1212XD-1W 12 12 84 108 77 43 1883 F1215XD-1W 12 15 67 108 77 42 1462 F1205XS-1W 12 5 200 121 69 26 2664 F1209XS-1W 12 9 111 113 74 35 2295 F1212XS-1W 12 12 84 108 77 43 1883 ◆Footprint 1.17cm2 F1215XS-1W 12 15 67 108 77 42 1462 F1505XS-1W 15 5 200 93 67 21 2747 ◆Industry standard pinout F1512XS-1W 15 12 84 85 75 45 1365 F1515XS-1W 15 15 67 84 77 50 941 E0505XD-1W 5 ±5 ±100 280 71.5 21 3106 E0509XD-1W 5 ±9 ±55 263 76 24 2258 E0512XD-1W 5 ±12 ±42 256 78 26 1579 E0515XD-1W 5 ±15 ±33 253 79 27 1065 ◆Internal SMD construction E0505XS-1W 5 ±5 ±100 280 71.5 21 3106 E0509XS-1W 5 ±9 ±55 263 76 24 2258 ◆Fully encapsulated with toroidal Magnetics E0512XS-1W 5 ±12 ±42 256 78 26 1579 ◆No external components required E0515XS-1W 5 ±15 ±33 253 79 27 1065 E1205XD-1W 12 ±5 ±100 117 71 27 2148 E1209XD-1W 12 ±9 ±55 113 74 35 1705 E1212XD-1W 12 ±12 ±42 111 75 42 1287 E1215XD-1W 12 ±15 ±33 110 76 41 924 E1205XS-1W 12 ±5 ±100 117 71 29 2148 E1209XS-1W 12 ±9 ±55 113 74 35 1705 E1212XS-1W 12 ±12 ±42 111 75 42 1287 E1215XS-1W 12 ±15 ±33 110 76 41 924 E1505XS-1W 15 ±5 ±100 91 69 39 1941 E1512XS-1W 15 ±12 ±42 87 75 68 789 E1515XS-1W 15 ±15 ±33 84 77 84 522 Order code FEATURES ◆RoHS compliant ◆Wide temperature performance at full 1 Watt load,-40°C to 85 °C ◆Single and dual output ◆UV 94V-0 package material ◆No heatsink required ◆ Power sharing on dual output ◆3KVDC isolation (1 minute) ◆5V,9V,12V and 15V output ◆MTTF up to 4.2 million hours ◆No electrolytic or tantalum capacitors ◆PCB mounting MODEL SELECTION ① ② ③ ④ ⑤ ⑥ E 05 05 X S -1W ①Product Series ③Output Voltage ⑤SIP Package ②Input Voltage ④Fixed Input ⑥Rated Power APPLICATIONS The E_X(S)D-1W&F_X(S)D-1W series of industrial temperature range DC/DC converters are the standard building blocks for on-board distributed power systems . They are ideally suited for providing local supplies on control system boards with the added benefit of 3kVDC galvanic isolation to reduce switching noise.Available in SIP and DIP with dual and single output pinout.All of the rated power may be drawn from a single pin provided the total load does not exceed 1 watt. (Rated Load) (PF) ABSOLUTE MAXIMUM RATINGS Short-circuit protection2 1 second Lead temperature 1.5mm from case for 10 seconds 300°C Internal power dissipation 560mW Input voltage VIN,E/F05 types 7V Input voltage VIN,E/F12 types 15V Input voltage VIN,E/F15 types 18V 1.Calculated using MIL-HDBK-217FN2 calculation model with nominal input voltage at full load. MICRODC reserves the copyright 2.Supply voltage must be disconnected at the end of the short circuit duration. All specifications typical at TA=25°C,nominal input voltage and rated output current unless otherwise specified. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 4 E-X(S)D-1W&F-X(S)D-1W Series OUTPUT CHARACTERISTICS Parameter Rated Power1 Voltage Set Point Accuracy Line regulation Conditions Min. Typ. Max. Units 1 W 1.0 1.2 %% Typ. Max. Units TA=-40°C to 120°C See tolerance envelope High Vin to low Vin INPUT CHARACTERISTICS Parameter Voltage range Conditions Min. Continuous operation,5V input types 4.5 5 5.5 V Continuous operation,12V input types 10.8 12 13.2 V Continuous operation,15V input types 13.5 15 16.5 V 20 40 MA p-p Typ. Max. Units Reflected ripple current ISOLATION CHARACTERISTICS Parameter Conditions Min. Isolation test voltage Flash tested for 1 minute 3000 VDC Resistance Viso=1000VDC 10 GΩ GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units 5V input types 120 135 kHz 12V input types 150 170 kHz 15V input types 90 110 kHz Typ. Max. Units -40 85 °C -50 125 °C 5V output types 28 °C All other output types 25 °C Switching frequency TEMPERATURE CHARACTERISTICS Parameter Conditions Specification All output types Min. Storage Case Tempetature above ambient TEMPERATURE DERATING GRAPH TOLERANCE ENVELOPE 1.See derating graph. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.Another 24V& 48V products, please inquire Our technical department! http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 4 E-X(S)D-1W&F-X(S)D-1W Series TECHNICAL NOTES ISOLATION VOLTAGE "Hi Pot Test","Flash Tested","Withstand Voltage","Dielectric Withstand Voltage"&”Isolation Test Voltage" are all terms that relate to the same thing, a test voltage. Applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Professional Power Module E_X(S)D&F_X(S)D series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 3KVDC for 1 minute. A question commonly asked is,"What is the continuous voltage that can be applied across the part in normal operation?" For a part holding no specific agency approvals, such as the E/F series ,both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC.The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier, but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-acssible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials. Construction and environment. The E_X(S)D&F_X(S)D series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing. but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. OUTPUT RIPPLE REDUCTION By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: Ceramic chip capacitors are recommended. It is required that the ESR(Equivalent Series Resistance)should be as low as possible.X7R types are recommended. The voltage rating should be at least twice(except for 15V output),the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF(Self Resonant Frequency) should be >20MHz. CHARACTERISATION TEST METHODS Ripple & Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1uF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter C2 10uF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter C3 100nF multilayer ceramic capacitor, general purpose R1 450Ω resistor, carbon film,+/-1% tolerance R2 50Ω BNC termination T1 3T of the caox cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 4 E-X(S)D-1W&F-X(S)D-1W Series PACKAGE SPECIFICATIONS PIN CONNECTIONS MECHANICAL DIMENSIONS DIP package SINGLE OUTPUT VARIANTS SIP package PIN CONNECTIONS-14 PIN DIP PIN CONNECTIONS-7 PIN SIP pin Function pin Function 1 -VIN 1 +VIN 7 NC 2 -VIN 8 +VOUT 5 -VOUT 10 -VOUT 7 +VOUT 14 +VIN DUAL OUTPUT VARIANTS PIN CONNECTIONS-14 PIN DIP *Pin not fitted on single output variants. All dimensions in inches ±0.01(mm±0.25mm).All pins on a 0.1(2.54) pitch and within ±0.01(0.25)of true position. Weight: 2.4g (DIP) 2.1g (SIP) PIN CONNECTIONS-7 PIN SIP pin Function pin Function 1 -VIN 1 +VIN 7 NC 2 -VIN 8 +VOUT 5 -VOUT 9 0V 6 0V 10 -VOUT 7 +VOUT 14 +VIN RECOMMENDED FOOTPRINT DETAILS 14 Pin DIP Package14 Pin DIP Package 7 Pin SIP Package *Hole not required for single output variants. TUBE OUTLINE DIMENSIONS 14 Pin DIP Tube 7 Pin SIP Tube Unless otherwise stated all dimensions in inches ±0.02(mm ±0.5mm). Tube length(14 Pin DIP):20.47(520mm±2mm). Tube length( 7 Pin SIP):20.47(520mm±2mm). Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:[email protected] Website:http://www.microdc.cn Microdc Professional Power module,Inc.makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. Specifications are subject to change without notice. 2010 Microdc Professional Power Module, Inc. Guangzhou http://www.microdc.cn Tube Quantity:10 RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 4 of 4