F-XM-1W Series 1W, FIXED INPUT, ISOLATED&UNREGULATED SINGLE OUTPUT DC-DC CONVERTER PRODUCT PROGRAM Input Part Number FEATURES ◆ ◆ ◆ ◆ High Efficiency up to 79% 3000VDC Isolation Temperature Range: -40℃～+85℃ No Heat sink Required ◆ No External Component Required ◆ No External Component Required ◆ Industry Standard Pin out ◆ RoHS Compliance Output Voltage (VDC) Current (mA) Efficiency (%,Typ) Package style Nominal Range Voltage (VDC) Min Max F0303XM -1W 3.3 3.0-3.6 3.3 300 30 70 SIP4 F0305XM -1W 3.3 3.0-3.6 5 200 20 73 SIP4 F0309XM-1W 3.3 3.0-3.6 9 111 12 74 SIP4 F0503XM -1W 5 4.5-5.5 3.3 300 30 71 SIP4 F0505XM -1W 5 4.5-5.5 5 200 20 69 SIP4 F0509XM -1W 5 4.5-5.5 9 111 12 76 SIP4 F0512XM -1W 5 4.5-5.5 12 83 9 78 SIP4 F0515XM -1W 5 4.5-5.5 15 67 7 78 SIP4 F1203XM -1W 12 10.8-13.2 3.3 300 30 74 SIP4 F1205XM -1W 12 10.8-13.2 5 200 20 71 SIP4 F1209XM -1W 12 10.8-13.2 9 111 12 74 SIP4 F1212XM -1W 12 10.8-13.2 12 83 9 78 SIP4 F1215XM -1W 12 10.8-13.2 15 67 7 79 SIP4 MODEL SELECTION ① ② ③ ④ ⑤ ⑥ F 05 05 X M -1W ①Product Series ③Output Voltage ⑤Mini SIP4 Package ②Input Voltage ④Fixed Input ⑥Rated Power ISOLATION SPECIFICATIONS Item Isolation voltage Isolation resistance Test conditions Min Tested for 1 minute and 1 mA max 3000 VDC Test at 500VDC 1000 MΩ Isolation Capacitance Typ Max Units 60 pF DESCRIPTION The F-XM-1W Series is specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤10%); 2) Where isolation is necessary between input and output (isolation voltage ≤3000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as:purely digital circuits,ordinary low frequency analog circuits,and IGBT power device driving circuits. COMMON SPECIFICATIONS Item Test conditions Min Typ Storage humidity Units 95 % Operating Temperature -40 85 Storage Temperature -55 125 Temp. rise at full load Lead temperature 15 1.5mm from case for 10 seconds Cooling ℃ 30 300 Short circuit protection* MICRODC RESERVES THE COPYRIGHT Max 1 S Free air convection Case material Plastic (UL94-V0) MTBF 3500 K hours Weight 4.3 g *Supply voltage must be discontinued at the end of short circuit duration. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 2 F-XM-1W Series APPLICATION NOTE OUTPUT SPECIFICATIONS Item Test conditions Output power Line regulation Min Typ 0.1 For Vin change of ±1% (3.3V output) Max Units 1 W ±1.5 % ±1.2 % (3.3V output) 15 20 % (5V output) 10 15 % (others output) Load 10% to 100% (9V output) 8.3 15 % regulation Load (12V output) 6.8 15 % (15V output) 6.3 15 % (24V output) 6.0 15 % Output voltage accuracy Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that his product should never be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load,or use our company's products with a lower rated output power. Recommended circuit If you want to further decrease the input/output ripple, an "LC" filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). See tolerance envelope graph Temperature drift 100% full load Ripple& Noise* 20MHz Bandwidth 100 Switching frequency Full load, nominal input 100 0.03 %/℃ 150 mVp-p KHz *Test ripple and noise by "Parallel cable" method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1. All specifications measured at T A =25 ℃ , humidity<75%, nominal input voltage and rated output load unless otherwise specified. It should also be noted that the inductance and the frequency of the "LC" filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the recommended capacitance of its filter capacitor sees (Table 1). 2. See below recommended circuits for more details. TYPICAL CHARACTERISTICS It not recommended to connect any external capacitor in the application field with less than 0.5 watt output. Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). OUTLINE DIMENSIONS & PIN CONNECTIONS Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload.The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:[email protected] Website:http://www.microdc.cn REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 2