® MUR1620CTA thru MUR1660CTA Pb MUR1620CTA thru MUR1660CTA Pb Free Plating Product 16.0 Ampere Heatsink Common Anode Ultra Fast Recovery Rectifiers Unit : inch (mm) TO-220AB .139(3.55) MIN .054(1.39) .045(1.15) .177(4.5)MAX Automotive Inverters/Solar Inverters Plating Power Supply,SMPS and UPS Car Audio Amplifiers and Sound Device Systems .038(0.96) .019(0.50) Mechanical Data Case: Heatsink TO-220AB Epoxy: UL 94V-0 rate flame retardant Terminals: Solderable per MIL-STD-202 method 208 Polarity: As marked on diode body Mounting position: Any Weight: 2.2 gram approximately .1(2.54) .548(13.93) .50(12.7)MIN Application .624(15.87) .196(5.00) .163(4.16) .269(6.85) .419(10.66) .387(9.85) .226(5.75) Features Fast switching for high efficiency Low forward voltage drop High current capability Low reverse leakage current High surge current capability .025(0.65)MAX .1(2.54) Case Case Positive Common Cathode Suffix "CT" Negative Common Anode Suffix "CTA" Case Doubler Tandem Polarity Suffix "CTD" MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL MUR1620CTA MUR1640CTA MUR1660CTA UNIT Maximum Recurrent Peak Reverse Voltage VRRM 200 400 600 V Maximum RMS Voltage VRMS 140 280 420 V Maximum DC Blocking Voltage VDC 200 400 600 V Maximum Average Forward Rectified 16.0 IF(AV) o Current TC=100 C A Peak Forward Surge Current, 8.3ms single Half sine-wave superimposed on rated load IFSM 175 VF 0.98 150 A (JEDEC method) Maximum Instantaneous Forward Voltage @ 8.0 A 1.3 o Maximum DC Reverse Current @TJ=25 C o At Rated DC Blocking Voltage @TJ=125 C IR uA 250 uA nS Trr 35 Typical junction Capacitance (Note 2) CJ 90 Operating Junction and Storage Temperature Range V 10.0 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 3) 1.7 R JC 2.2 TJ, TSTG -55 to + 150 pF o CW o C NOTES : (1) Reverse recovery test conditions IF = 0.5A, IR = 1.0A, Irr = 0.25A. (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts DC. (3) Thermal Resistance junction to case. Rev.04/2014 © 2006 Thinki Semiconductor Co.,Ltd. Page 1/2 http://www.thinkisemi.com/ ® MUR1620CTA thru MUR1660CTA FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE 200 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 16 13 10 8 6 4 60 Hz Resistive or Inductive load Pulse Width 8.3ms Single Half-Sire-Wave (JEDEC Method) 175 150 125 100 75 50 25 0 0 0 50 100 150 1 100 NUMBER OF CYCLES AT 60Hz o CASE TEMPERATURE, C FIG.4 - TYPICAL REVERSE CHARACTERISTICS FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 80 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 10 MUR1620CTA MUR1640CTA 8 MUR1660CTA 0.1 o TJ=25 C PULSE WIDTH=300uS 1% DUTY CYCLE 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 o TJ=125 C 100 10 o TJ=25 C 1 0.1 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1000 o TJ = 25 C f = 1.0 MHZ Vsig = 50mVp-p 100 10 0.1 1.0 4.0 10 100 REVERSE VOLTAGE, VOLTS Rev.04/2014 © 2006 Thinki Semiconductor Co.,Ltd. Page 2/2 http://www.thinkisemi.com/