SFF1004GA thru SFF1008GA ® Pb SFF1004GA thru SFF1008GA Pb Free Plating Product 10.0 Ampere Isolated Dual Common Anode Super Fast Rectifiers Unit : inch (mm) ITO-220AB .189(4.8) .165(4.2) .272(6.9) .248(6.3) .406(10.3) .381(9.7) .134(3.4) .118(3.0) .130(3.3) .114(2.9) Application Automotive Inverters/Solar Inverters Plating Power Supply,Adaptor,SMPS and UPS Car Audio Amplifiers and Sound Device Systems .161(4.1)MAX .071(1.8) .055(1.4) .055(1.4) .039(1.0) .035(0.9) .011(0.3) Mechanical Data Case: ITO-220AB Isolated full plastic pkg Epoxy: UL 94V-0 rate flame retardant Terminals: Solderable per MIL-STD-202 method 208 Polarity: As marked on diode body Mounting position: Any Weight: 2.0 gram approximately .1 .1 (2.55) (2.55) .543(13.8) .512(13.0) .606(15.4) .583(14.8) .112(2.85) .100(2.55) Features Fast switching for high efficiency Low forward voltage drop High current capability Low reverse leakage current High surge current capability .114(2.9) .098(2.5) .032(.8) MAX Case Case Negative Common Anode Suffix "GA" Positive Common Cathode Suffix "G" Case Doubler Tandem Polarity Suffix "GD" MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL SFF1004G SFF1006G SFF1008G SFF1004GA SFF1006GA SFF1008GA UNIT SFF1004GD SFF1006GD SFF1008GD Maximum Recurrent Peak Reverse Voltage VRRM 200 400 600 V Maximum RMS Voltage VRMS 140 280 420 V Maximum DC Blocking Voltage VDC 200 400 600 V Maximum Average Forward Rectified o Current TC=100 C IF(AV) 10.0 A IFSM 100 A Peak Forward Surge Current, 8.3ms single Half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage @ 5.0 A VF 0.98 o Maximum DC Reverse Current @TJ=25 C o At Rated DC Blocking Voltage @TJ=125 C IR 1.3 uA 250 uA nS Trr 35 Typical junction Capacitance (Note 2) CJ 65 Operating Junction and Storage Temperature Range V 10.0 Maximum Reverse Recovery Time (Note 1) Typical Thermal Resistance (Note 3) 1.7 R JC 2.2 TJ, TSTG -55 to +150 pF o CW o C NOTES : (1) Reverse recovery test conditions IF = 0.5A, IR = 1.0A, Irr = 0.25A. (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts DC. (3) Thermal Resistance junction to case. Rev.04/2014 © 2006 Thinki Semiconductor Co.,Ltd. Page 1/2 http://www.thinkisemi.com/ SFF1004GA thru SFF1008GA ® FIG.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1 - FORWARD CURRENT DERATING CURVE 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 10 8 6 4 2 60 Hz Resistive or Inductive load 0 Pulse Width 8.3ms Single Half-Sire-Wave (JEDEC Method) 80 60 40 20 0 0 50 100 150 1 CASE TEMPERATURE, C 100 FIG.4 - TYPICAL REVERSE CHARACTERISTICS FIG.3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1000 50 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES IINSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60Hz o SFF1004GA SFF1006GA 5 SFF1008GA 1 o TJ=25 C PULSE WIDTH=300uS 1% DUTY CYCLE 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 o TJ=125 C 100 10 o TJ=25 C 1 0.1 0 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% FIG.5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1000 o TJ = 25 C f = 1.0 MHZ Vsig = 50mVp-p 100 10 0.1 1.0 4.0 10 100 REVERSE VOLTAGE, VOLTS Rev.04/2014 © 2006 Thinki Semiconductor Co.,Ltd. Page 2/2 http://www.thinkisemi.com/