EP7209 EP7209 FEATURES ■ Audio decoder system-on-chip Ultra-Low-Power Audio Decoder System-on-Chip — Allows for support of multiple audio decompression algorithms — Supports MPEG 1, 2, & 2.5 layer 3 audio decoding, including ISO compliant MPEG 1 & 2 layer 3 support for all standard sample rates and bit rates — Supports bit streams with adaptive bit rates — DAI (Digital Audio Interface) providing glueless interface to low power DACs, ADCs, and Codecs OVERVIEW The EP7209 is a complete integrated system on a chip for enabling personal digital audio solutions. It is designed specifically for implementing audio processing algorithms in power sensitive applications. The core-logic functionality of the device is built around an ARM720T embedded processor. ■ Ultra low power consumption for MP3 playback — 87 mW (typical) for 44.1 kHz samples/sec, 128 kbits/second — 50 mW for 22.05 kHz samples/sec, 64 kbits/second — <1 mW in Standby State ■ ARM720T processor — — — — — — ARM7TDMI CPU 8 kbytes of four-way set-associative cache MMU with 64-entry TLB (transition look-aside buffer) Write Buffer Windows CE enabled Thumb code support enabled (cont.) The EP7209 also includes a 32-bit Y2K-compliant Real-Time Clock (RTC) and comparator. (cont.) Functional Block Diagram 13-MHZ INPUT INTERNAL DATA BUS PLL 3.6864 MHZ D[0:31] ARM720T 32.768 KHZ 32.768-KHZ OSCILLATOR NPOR, RUN, RESET, WAKEUP STATE CONTROL BATOK, NEXTPWR PWRFL, BATCHG POWER MANAGEMENT EINT[1:3], FIQ, MEDCHG FLASHING LED DRIVE INTERRUPT CONTROLLER PORTS A, B, D (8-BIT) PORT E (3-BIT) KEYBD DRIVERS (0:7) BUZZER DRIVE DC-TO-DC ADCCLK, ADCIN, ADCOUT, SMPCLK, ADCCS ARM7TDMI CPU CORE MEMORY CONTROLLER 8-KBYTE CACHE CL-PS6700 INTFC. PB[0:1], NCS[4:5] EXPANSION CONTROL EXPCLK, WORD, NCS[0:3], EXPRDY, WRITE MMU WRITE BUFFER INTERNAL ADDRESS BUS RTC LCD DMA GPIO TIMER COUNTERS (2) PWM SSI1 (ADC) SSICLK, SSITXFR, SSITXDA, SSIRXDA, SSIRSFR P.O. Box 17847, Austin, Texas 78760 (512) 445 7222 FAX: (512) 445 7581 http://www.cirrus.com ON-CHIP BOOT ROM DAI SSI2 CODEC ICE-JTAG LCD CONTROLLER ON-CHIP SRAM 38,400 BYTES EPB BRIDGE EPB BUS A[0:27], DRA[0:12] TEST AND DEVELOPMENT LCD DRIVE IrDA LED AND PHOTODIODE UART1 ASYNC INTERFACE 1 UART2 ASYNC INTERFACE 2 Copyright Cirrus Logic, Inc. 1999 (All Rights Reserved) DEC ‘99 DS453PP2 1 EP7209 FEATURES (cont.) ■ Dynamically programmable clock speeds of 18, 36, 49, and 74 MHz at 2.5 V ■ Performance matching 100 MHz Intel Pentium-based PC ■ OEM customization — Integrated ARM720T RISC processor — Up to 25 MHz of CPU processing power available (after digital audio decoding) for custom features such as software EQ or tone control, volume control, spectrum analyzer, random play order, etc. — Allows for control of digital voice recorder function ■ LCD controller — Interfaces directly to a single-scan panel monochrome LCD — Panel width is programmable from 32 to 1024 pixels in 16-pixel increments — Video frame buffer size programmable up to 128 kbytes — Bits per pixel of 1, 2, or 4 bits ■ Memory controller — Decodes up to 6 separate memory segments of up to 256 Mbytes each — Each segment can be configured as 8, 16, or 32 bits wide and supports page-mode access — Programmable access time for conventional ROM/SRAM/FLASH memory — Supports Removable FLASH card interface — Enables connection to removable FLASH card for addition of expansion FLASH memory modules ■ 38,400 bytes (0x9600) of on-chip SRAM for fast program execution and/or as a frame buffer ■ On-chip boot ROM for manufacturing support ■ Integrated DAI interface — Connects directly to a Crystal® audio DAC ■ 27-bits of general-purpose I/O — Three 8-bit and one 3-bit GPIO port — Supports scanning keyboard matrix ■ SIR (up to 115.2 kbps) infrared encoder/decoder — IrDA (Infrared Data Association) SIR protocol encoder/decoder ■ DC-to-DC converter interface (PWM) — Provides two 96 kHz clock outputs with programmable duty ratio (from 1-in-16 to 15-in-16) that can be used to drive a DC to DC converter ■ 208-pin LQFP or 256-ball PBGA packages ■ Full JTAG boundary scan and Embedded ICE support OVERVIEW (cont.) The EP7209 also includes a comprehensive set of integrated peripherals such as an LCD display controller, an audio DAC interface, and a FLASH memory interface. Using the EP7209, a portable audio decoder solution can be built with the addition of an LCD display, an audio DAC, a FLASH memory subsystem, and a small number of additional low cost components. The EP7209 uses its powerful 32-bit RISC processing engine to implement audio decompression algorithms in software. The nature of the on-board RISC processor and the availability of efficient C-compilers and other software development tools ensures that a wide range of audio decompression algorithms can easily be ported to and run on the EP7209. The EP7209 uses external memory for storing application code. The use of external memory to support software audio decompression algorithms ensures that the audio decompression system solution can be tailored to the requirements of the application. Software can be placed in a low cost mask ROM for price 2 sensitive applications, or can be placed in external FLASH memory to enable upgradeable systems. The EP7209’s 8 kbyte on-board cache and programmable wait state generator ensure that a wide range of memory options can be utilized. The EP7209 runs a full ISO-compliant MPEG 1, 2, & 2.5 layer 3 audio decompression engine with less than 50% of its available processing capability. This leaves significant processing power available for product differentiation. MPEG 1, 2, & 2.5 Layer 3 Object Code Library Cirrus Logic provides an object code library for enabling MPEG 1, 2, & 2.5 layer 3 audio decompression. This library supports the MPEG 1 sample rates of 48 k, 44.1 k and 32 k bits per second; the MPEG 2 sample rates of 24 k, 22.05 k and 16 k bits per second; and the MPEG 2.5 sample rates of 12 k, 11.025 k and 8 k bits per second. In addition to all standard fixed compressed data rates, the MPEG layer 3 object code library also supports decompression of variable bit-rate data streams. DS453PP2 EP7209 OVERVIEW (cont.) Power Management The EP7209 is designed for ultra-low-power operation. Its core operates at only 2.5 V, while its I/O has an operation range of 2.5 V-3.3 V. Through careful design, Cirrus Logic has achieved extremely low power consumption with the EP7209. This is achieved by using a combination of dynamically adjustable core clock frequencies, low power states utilized during periods of inactivity, and fully static design principles. For example, when decompressing MPEG 1 layer 3 music data with sample rates of 44.1 kHz and 128 kbits/sec, the EP7209 consumes less than 87 mW. At sampling frequencies of 22.05 kHz and 64 kbits/sec, power consumption falls to 50 mW. downloading of compressed music or data from a PC to an EP7209-based portable digital audio player. The EP7209 can also be connected to industry standard USB slave devices through an external interface. The power of the EP7209 coupled with the 36 MHz external data bus ensures that the EP7209 can support rapid transfer of compressed audio data over a USB interface. The EP7209 also includes a built-in 115.2 kbps IrDA SIR protocol encoder/decoder that can be used to drive an infrared communication interface to download the data. Digital Audio Interface The EP7209 connects directly to both on-system FLASH memory and to removable FLASH memorycards. The generality of the external interface on the EP7209 allows for the use of a wide variety of additional memory types for compressed audio data storage. The EP7209 integrates an DAI interface to enable a direct connection to many low cost, low power, high quality audio converters. In particular, the DAI interface can be used to drive the Crystal CS43L41 / 42 / 43 low power audio DACs and the Crystal CS53L32 low power audio ADC. Some of these devices feature digital bass and treble boost, digital volume control and compressor-limiter functions. LCD Interface Packaging The EP7209 interfaces directly to a single-scan panel monochrome LCD display. For portable digital audio player applications that require LCDs, a 128 kbyte display buffer is provided. The EP7209 is available in a 208-pin LQFP package and a 256-ball PBGA package. Data Download As shown in the system block diagram, simply adding FLASH memory, an LCD, an audio DAC, and some discrete components, a complete low power digital audio player system can be made. (See the following illustration). Audio Data Memory Interfaces The EP7209 along with minimal glue logic can connect to a PC through the parallel port. This enables System Design Contacting Cirrus Logic Support For a complete listing of Direct Sales, Distributor, and Sales Representative contacts, visit the Cirrus Logic web site at: http://www.cirrus.com/corporate/contacts/ Preliminary product information describes products which are in production, but for which full characterization data is not yet available. Advance product information describes products which are in development and subject to development changes. Cirrus Logic, Inc. has made best efforts to ensure that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind (express or implied). No responsibility is assumed by Cirrus Logic, Inc. for the use of this information, nor for infringements of patents or other rights of third parties. This document is the property of Cirrus Logic, Inc. and implies no license under patents, copyrights, trademarks, or trade secrets. No part of this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or otherwise) without the prior written consent of Cirrus Logic, Inc. Items from any Cirrus Logic website or disk may be printed for use by the user. However, no part of the printout or electronic files may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or otherwise) without the prior written consent of Cirrus Logic, Inc.Furthermore, no part of this publication may be used as a basis for manufacture or sale of any items without the prior written consent of Cirrus Logic, Inc. The names of products of Cirrus Logic, Inc. or other vendors and suppliers appearing in this document may be trademarks or service marks of their respective owners which may be registered in some jurisdictions. A list of Cirrus Logic, Inc. trademarks and service marks can be found at http://www.cirrus.com. DS453PP2 3 EP7209 OVERVIEW (cont.) CRYSTAL MOSCIN CRYSTAL RTCIN LCD COL[7:0] D[31:0] A[27:0] FLASH CARD/ FLASH MEMORY PA[7:0] KEYBOARD/ PUSH BUTTONS NMOE NMWE EINT[X] CS[3] SMART MEDIA CARD INTERFACE CS[0] EP7209 PC PARALLEL PORT PE[2:0] NPOR NPWRFL NBATOK NEXTPWR NBATCHG RUN WAKEUP POWER SUPPLY UNIT AND COMPARATORS BATTERY CS[1] NOR FLASH × 16 HEADPHONES PB[6:7] NAND FLASH ×8 SSICLK SSITXFR SSITXDA SSIRXDA STEREO DAC CS43L41 / 42 / 43 STEREO ADC CS53L32 MIC USB CS[4] Figure 1. A Typical EP7209-Based Digital Audio Player Reference 4 DS453PP2 EP7209 EP7209 TABLE OF CONTENTS 1. CONVENTIONS ...................................................................................................................... 10 1.1 Acronyms and Abbreviations ............................................................................................ 10 1.2 Units of Measurement ...................................................................................................... 11 1.3 General Conventions ........................................................................................................ 11 1.4 Pin Description Conventions ............................................................................................. 11 2. PIN INFORMATION ................................................................................................................ 12 2.1 208-Pin LQFP Pin Diagram .............................................................................................. 12 2.2 Pin Descriptions ................................................................................................................ 13 2.2.1 External Signal Functions ................................................................................... 13 2.2.2 SSI/Codec/DAI Pin Multiplexing ............................................................................ 16 2.2.3 Output Bi-Directional Pins .................................................................................... 17 3. FUNCTIONAL DESCRIPTION ............................................................................................... 18 3.1 CPU Core .......................................................................................................................... 19 3.2 State Control ..................................................................................................................... 20 3.2.1 Standby State .......................................................................................................... 20 3.2.1.1 UART in Standby State ............................................................................... 21 3.2.2 Idle State ................................................................................................................. 22 3.2.3 Keyboard Interrupt ................................................................................................... 22 3.3 Resets ............................................................................................................................... 23 3.4 Clocks ............................................................................................................................... 23 3.4.1 On-Chip PLL ............................................................................................................ 23 3.4.1.1 Characteristics of the PLL Interface ............................................................ 24 3.4.2 External Clock Input (13 MHz) ................................................................................ 24 3.4.3 Dynamic Clock Switching When in the PLL Clocking Mode .................................... 26 3.5 Interrupt Controller ............................................................................................................ 26 3.5.1 Interrupt Latencies in Different States ..................................................................... 28 3.5.1.1 Operating State ........................................................................................... 28 3.5.1.2 Standby State .............................................................................................. 28 3.6 EP7209 Boot ROM .......................................................................................................... 29 3.7 Memory and I/O Expansion Interface ............................................................................... 30 3.8 CL-PS6700 PC Card Controller Interface ......................................................................... 31 3.9 Endianness ....................................................................................................................... 33 3.10 Internal UARTs (Two) and SIR Encoder ......................................................................... 34 3.11 Serial Interfaces .............................................................................................................. 34 3.11.1 Codec Sound Interface .......................................................................................... 36 3.11.2 Digital Audio Interface ........................................................................................... 37 3.11.2.1 DAI Operation ............................................................................................ 38 3.11.2.2 DAI Frame Format ..................................................................................... 38 3.11.2.3 DAI Signals ................................................................................................ 38 3.11.3 ADC Interface — Master Mode Only SSI1 (Synchronous Serial Interface) .......... 39 3.11.4 Master/Slave SSI2 (Synchronous Serial Interface 2) ........................................... 39 3.11.4.1 Read Back of Residual Data ..................................................................... 42 3.11.4.2 Support for Asymmetric Traffic .................................................................. 42 3.11.4.3 Continuous Data Transfer ......................................................................... 43 3.11.4.4 Discontinuous Clock .................................................................................. 43 3.11.4.5 Error Conditions ........................................................................................ 43 3.11.4.6 Clock Polarity ............................................................................................ 43 3.12 LCD Controller with Support for On-Chip Frame Buffer .................................................. 43 3.13 Timer Counters ............................................................................................................... 45 3.13.1 Free Running Mode ............................................................................................... 46 3.13.2 Prescale Mode ...................................................................................................... 46 3.14 Real Time Clock .............................................................................................................. 46 DS453PP2 DS453PP2 5 EP7209 3.14.1 Characteristics of the Real Time Clock Interface ................................................... 46 3.15 Dedicated LED Flasher ................................................................................................... 47 3.16 Two PWM Interfaces ....................................................................................................... 47 3.17 Boundary Scan ................................................................................................................ 47 3.18 In-Circuit Emulation ......................................................................................................... 48 3.18.1 Introduction ............................................................................................................ 48 3.18.2 Functionality ........................................................................................................... 48 3.19 Maximum EP7209-Based System .................................................................................. 48 4. MEMORY MAP ....................................................................................................................... 50 5. REGISTER DESCRIPTIONS .................................................................................................. 51 5.1 Internal Registers .............................................................................................................. 51 5.1.1 PADR Port A Data Register ..................................................................................... 54 5.1.2 PBDR Port B Data Register ..................................................................................... 54 5.1.3 PDDR Port D Data Register .................................................................................... 54 5.1.4 PADDR Port A Data Direction Register ................................................................... 54 5.1.5 PBDDR Port B Data Direction Register ................................................................... 54 5.1.6 PDDDR Port D Data Direction Register ................................................................... 55 5.1.7 PEDR Port E Data Register ..................................................................................... 55 5.1.8 PEDDR Port E Data Direction Register ................................................................... 55 5.2 SYSTEM Control Registers ............................................................................................... 56 5.2.1 SYSCON1 The System Control Register 1 ............................................................. 56 5.2.2 SYSCON2 System Control Register 2 ..................................................................... 59 5.2.3 SYSCON3 System Control Register 3 ..................................................................... 61 5.2.4 SYSFLG1 — The System Status Flags Register .................................................... 62 5.2.5 SYSFLG2 System Status Register 2 ....................................................................... 64 5.3 Interrupt Registers ............................................................................................................. 65 5.3.1 INTSR1 Interrupt Status Register 1 ......................................................................... 65 5.3.2 INTMR1 Interrupt Mask Register 1 .......................................................................... 67 5.3.3 INTSR2 Interrupt Status Register 2 ......................................................................... 67 5.3.4 INTMR2 Interrupt Mask Register 2 .......................................................................... 68 5.3.5 INTSR3 Interrupt Status Register 3 ......................................................................... 68 5.3.6 INTMR3 Interrupt Mask Register 3 .......................................................................... 68 5.4 Memory Configuration Registers ....................................................................................... 69 5.4.1 MEMCFG1 Memory Configuration Register 1 ......................................................... 69 5.4.2 MEMCFG2 Memory Configuration Register 2 ......................................................... 69 5.5 Timer/Counter Registers ................................................................................................... 71 5.5.1 TC1D Timer Counter 1 Data Register ..................................................................... 71 5.5.2 TC2D Timer Counter 2 Data Register ..................................................................... 71 5.5.3 RTCDR Real Time Clock Data Register .................................................................. 71 5.5.4 RTCMR Real Time Clock Match Register ............................................................... 71 5.6 LEDFLSH Register ............................................................................................................ 72 5.7 PMPCON Pump Control Register ..................................................................................... 73 5.8 CODR — The CODEC Interface Data Register ................................................................ 74 5.9 UART Registers ................................................................................................................ 74 5.9.1 UARTDR1–2 UART1–2 Data Registers .................................................................. 74 5.9.2 UBRLCR1–2 UART1–2 Bit Rate and Line Control Registers .................................. 75 5.10 LCD Registers ................................................................................................................. 77 5.10.1 LCDCON — The LCD Control Register ................................................................. 77 5.10.2 PALLSW Least Significant Word — LCD Palette Register .................................... 78 5.10.3 PALMSW Most Significant Word — LCD Palette Register .................................... 78 5.10.4 FBADDR LCD Frame Buffer Start Address ........................................................... 79 5.11 SSI Register .................................................................................................................... 79 5.11.1 SYNCIO Synchronous Serial ADC Interface Data Register .................................. 79 5.12 STFCLR Clear all ‘Start Up Reason’ flags location ......................................................... 80 6 DS453PP2 EP7209 5.13 ‘End Of Interrupt’ Locations ............................................................................................ 81 5.13.1 BLEOI Battery Low End of Interrupt ...................................................................... 81 5.13.2 MCEOI Media Changed End of Interrupt .............................................................. 81 5.13.3 TEOI Tick End of Interrupt Location ...................................................................... 81 5.13.4 TC1EOI TC1 End of Interrupt Location ................................................................. 81 5.13.5 TC2EOI TC2 End of Interrupt Location ................................................................. 82 5.13.6 RTCEOI RTC Match End of Interrupt .................................................................... 82 5.13.7 UMSEOI UART1 Modem Status Changed End of Interrupt .................................. 82 5.13.8 COEOI Codec End of Interrupt Location ............................................................... 82 5.13.9 KBDEOI Keyboard End of Interrupt Location ........................................................ 82 5.13.10 SRXEOF End of Interrupt Location ..................................................................... 82 5.14 State Control Registers ................................................................................................... 82 5.14.1 STDBY Enter the Standby State Location ............................................................. 82 5.14.2 HALT Enter the Idle State Location ....................................................................... 82 5.15 SS2 Registers ................................................................................................................. 83 5.15.1 SS2DR Synchronous Serial Interface 2 Data Register ......................................... 83 5.15.2 SS2POP Synchronous Serial Interface 2 Pop Residual Byte ............................... 83 5.16 DAI Register Definitions .................................................................................................. 83 5.16.1 DAI Control Register ............................................................................................. 84 5.16.1.1 DAI Enable (DAIEN) .................................................................................. 85 5.16.1.2 DAI Interrupt Generation ........................................................................... 85 5.16.1.3 Left Channel Transmit FIFO Interrupt Mask (LCTM) ................................. 85 5.16.1.4 Left Channel Receive FIFO Interrupt Mask (LARM) ................................. 85 5.16.1.5 Right Channel Transmit FIFO Interrupt Mask (RCTM) .............................. 86 5.16.1.6 Right Channel Receive FIFO Interrupt Mask (RCRM) .............................. 86 5.16.1.7 Loop Back Mode (LBM) ............................................................................. 86 5.16.2 DAI Data Registers ................................................................................................ 87 5.16.2.1 DAI Data Register 0 .................................................................................. 87 5.16.2.2 DAI Data Register 1 .................................................................................. 88 5.16.2.3 DAI Data Register 2 .................................................................................. 88 5.16.3 DAI Status Register ............................................................................................... 89 5.16.3.1 Right Channel Transmit FIFO Service Request Flag (RCTS) ................... 89 5.16.3.2 Right Channel Receive FIFO Service Request Flag (RCRS) ................... 89 5.16.3.3 Left Channel Transmit FIFO Service Request Flag (LCTS) ...................... 89 5.16.3.4 Left Channel Receive FIFO Service Request Flag (LCRS) ...................... 90 5.16.3.5 Right Channel Transmit FIFO Underrun Status (RCTU) ........................... 90 5.16.3.6 Right Channel Receive FIFO Overrun Status (RCRO) ............................. 90 5.16.3.7 Left Channel Transmit FIFO Underrun Status (LCTU) .............................. 90 5.16.3.8 Left Channel Receive FIFO Overrun Status (LCRO) ................................ 90 5.16.3.9 Right Channel Transmit FIFO Not Full Flag (RCNF) ................................. 90 5.16.3.10 Right Channel Receive FIFO Not Empty Flag (RCNE) ........................... 90 5.16.3.11 Left Channel Transmit FIFO Not Full Flag (LCNF) .................................. 91 5.16.3.12 Left Channel Receive FIFO Not Empty Flag (LCNE) .............................. 91 5.16.3.13 FIFO Operation Completed Flag (FIFO) ................................................. 91 6. ELECTRICAL SPECIFICATIONS .......................................................................................... 93 6.1 Absolute Maximum Ratings .............................................................................................. 93 6.2 Recommended Operating Conditions .............................................................................. 93 6.3 DC Characteristics ............................................................................................................ 93 6.4 AC Characteristics ............................................................................................................ 95 6.5 I/O Buffer Characteristics ................................................................................................ 102 6.6 JTAG Bandary Scan Signal Ordering ............................................................................. 102 7. TEST MODES ....................................................................................................................... 106 7.1 Oscillator and PLL Bypass Mode .................................................................................... 106 7.2 Oscillator and PLL Test Mode ......................................................................................... 106 DS453PP2 7 EP7209 7.3 Debug/ICE Test Mode .................................................................................................... 107 7.4 Hi-Z (System) Test Mode ............................................................................................... 107 7.5 Software Selectable Test Functionality .......................................................................... 107 8. PIN INFORMATION .............................................................................................................. 108 8.1 208-Pin LQFP Pin Diagram ............................................................................................. 108 8.2 208-Pin LQFP Numeric Pin Listing ................................................................................. 109 8.3 256-Pin PBGA Pin Diagram ............................................................................................ 112 8.4 256-Ball PBGA Ball Listing .............................................................................................. 113 8.4.1 PBGA Ground Connections ................................................................................... 116 9. PACKAGE SPECIFICATIONS ............................................................................................. 117 9.1 208-Pin LQFP Package Outline Drawing ....................................................................... 117 9.2 EP7209 256-Ball PBGA (17 × 17 × 1.53-mm Body) Dimensions .................................. 118 10. ORDERING INFORMATION ............................................................................................... 119 11. APPENDIX A: BOOT CODE .............................................................................................. 120 12. INDEX ................................................................................................................................. 125 LIST OF FIGURES Figure 1. 208-Pin LQFP (Low Profile Quad Flat Pack) Pin Diagram............................................. 12 Figure 2. EP7209 Block Diagram .................................................................................................. 19 Figure 3. State Diagram ................................................................................................................ 20 Figure 4. CLKEN Timing Entering the Standby State ................................................................... 25 Figure 5. CLKEN Timing Entering the Standby State ................................................................... 25 Figure 6. Codec Interrupt Timing................................................................................................... 36 Figure 7. DAI Interface .................................................................................................................. 37 Figure 8. EP7209 Rev C - Digital Audio Interface Timing – MSB/Left Justified format ................ 38 Figure 9. SSI2 Port Directions in Slave and Master Mode ............................................................ 40 Figure 10. Residual Byte Reading................................................................................................. 42 Figure 11. Video Buffer Mapping................................................................................................... 45 Figure 12. A Maximum EP7209 Based System ............................................................................ 49 Figure 13. Consecutive Memory Read Cycles with Minimum Wait States.................................... 97 Figure 14. Sequential Page Mode Read Cycles with Minimum Wait States ................................. 98 Figure 15. Consecutive Memory Write Cycles with Minimum Wait States .................................... 99 Figure 16. LCD Controller Timings.............................................................................................. 100 Figure 17. SSI Interface for AD7811/2 ........................................................................................ 100 Figure 18. SSI Timing Interface for MAX148/9............................................................................ 101 Figure 19. SSI2 Interface Timings............................................................................................... 101 Figure 20. 208-Pin LQFP (Low Profile Quad Flat Pack) Pin Diagram......................................... 108 Figure 21. 256-Ball Plastic Ball Grid Array Diagram ................................................................... 112 LIST OF TABLES Table 1. Acronyms and Abbreviations........................................................................................... 10 Table 2. Unit of Measurement ....................................................................................................... 11 Table 3. Pin Description Conventions ........................................................................................... 11 Table 4. External Signal Functions................................................................................................ 13 Table 5. SSI/Codec/DAI Pin Multiplexing ...................................................................................... 16 Table 6. Output Bi-Directional Pins ............................................................................................... 17 Table 7. Peripheral Status in Different Power Management States .............................................. 21 Table 8. Exception Priority Handling ............................................................................................. 26 Table 9. Interrupt Allocation in the First Interrupt Register............................................................ 27 Table 10. Interrupt Allocation in the Second Interrupt Register..................................................... 27 Table 11. Interrupt Allocation in the Third Interrupt Register......................................................... 27 Table 12. External Interrupt Source Latencies .............................................................................. 29 Table 13. Chip Select Address Ranges After Boot From On-Chip Boot ROM.............................. 29 8 DS453PP2 EP7209 Table 14. Boot Options ................................................................................................................. 30 Table 15. CL-PS6700 Memory Map.............................................................................................. 31 Table 16. Space Field Decoding ................................................................................................... 32 Table 19. Serial Interface Options................................................................................................. 35 Table 20. Serial-Pin Assignments ................................................................................................. 35 Table 21. ADC Interface Operation Frequencies .......................................................................... 39 Table 17. Effect of Endianness on Read Operations .................................................................... 41 Table 18. Effect of Endianness on Write Operations .................................................................... 41 Table 22. Instructions Supported in JTAG Mode .......................................................................... 47 Table 23. Device ID Register ........................................................................................................ 48 Table 24. EP7209 Memory Map in External Boot Mode ............................................................... 50 Table 25. EP7209 Internal Registers Compatible with CL-PS7111 (Little Endian Mode)............. 52 Table 26. EP7209 Internal Registers (Big Endian Mode) ............................................................. 54 Table 27. SYSCON1 ..................................................................................................................... 56 Table 28. SYSCON2 ..................................................................................................................... 59 Table 29. SYSCON3 ..................................................................................................................... 61 Table 30. SYSFLG ........................................................................................................................ 62 Table 31. SYSFLG2 ...................................................................................................................... 64 Table 32. INTSR1 ......................................................................................................................... 65 Table 34. INTSR3 ......................................................................................................................... 68 Table 35. Values of the Bus Width Field ....................................................................................... 70 Table 36. Values of the Wait State Field at 13 MHz and 18 MHz ................................................. 70 Table 37. Values of the Wait State Field at 36 MHz ..................................................................... 70 Table 38. MEMCFG ...................................................................................................................... 71 Table 39. LED Flash Rates ........................................................................................................... 72 Table 40. LED Duty Ratio ............................................................................................................. 72 Table 41. PMPCON ...................................................................................................................... 73 Table 42. Sense of PWM control lines .......................................................................................... 73 Table 43. UARTDR1-2 UART1-2 .................................................................................................. 74 Table 44. UBRLCR1-2 UART1-2 .................................................................................................. 75 Table 45. LCDCON ....................................................................................................................... 77 Table 46. Gray Scale Value to Color Mapping.............................................................................. 79 Table 47. SYNCIO ........................................................................................................................ 80 Table 48. DAI Control Register ..................................................................................................... 84 Table 49. DAI Data Register 0 ...................................................................................................... 87 Table 50. DAI Data Register 1 ...................................................................................................... 88 Table 51. DAI Control, Data and Status Register Locations ......................................................... 91 Table 52. absolute Maximum Ratings........................................................................................... 93 Table 53. Recommended Operating Conditions ........................................................................... 93 Table 54. DC Characteristics ........................................................................................................ 93 Table 55. AC Timing Characteristics............................................................................................. 95 Table 56. Timing Characteristics................................................................................................... 96 Table 57. I/O Buffer Output Characteristics ................................................................................ 102 Table 58. 208-Pin LQFP Numeric Pin Listing ............................................................................. 102 Table 59. EP7209 Hardware Test Modes ................................................................................... 106 Table 60. Oscillator and PLL Test Mode Signals ........................................................................ 107 Table 61. Software Selectable Test Functionality ....................................................................... 107 Table 62. 208-Pin LQFP Numeric Pin Listing ............................................................................. 109 Table 63. 256-Ball PBGA Ball Listing.......................................................................................... 113 Table 64. PBGA Balls to Connect to Ground (VSS) .................................................................... 116 DS453PP2 9 EP7209 1. CONVENTIONS This section presents acronyms, abbreviations, units of measurement, and conventions used in this data sheet. 1.1 Acronyms and Abbreviations Table 1 lists abbreviations and acronyms used in this data sheet. Acronym/ Abbreviation Definition Acronym/ Abbreviation Definition LCD liquid crystal display. LED light-emitting diode. LQFP low profile quad flat pack. LSB least significant bit. MIPS millions of instructions per second. MMU memory management unit. MSB most significant bit. PBGA plastic ball grid array. PCB printed circuit board. PDA personal digital assistant. PIA peripheral interface adapter. PLL phase locked loop. AC alternating current. A/D analog-to-digital. ADC analog-to-digital converter. CMOS complementary metal oxide semiconductor. CODEC coder/decoder. PSU power supply unit. CPU central processing unit. p/u pull-up resistor. D/A digital-to-analog. RAM random access memory. DC direct current. RISC DMA direct-memory access. reduced instruction set computer. EPB embedded peripheral bus. ROM read-only memory. FCS frame check sequence. RTC Real Time Clock. FIFO first in/first out. SIR slow (9600–115.2 kbps) infrared. GPIO general purpose I/O. SRAM static random access memory. ICT in circuit test. SSI synchronous serial interface. IR infrared. TAP test access port. IrDA Infrared Data Association. TLB translation lookaside buffer. JTAG Joint Test Action Group. UART universal asynchronous receiver. Table 1. Acronyms and Abbreviations 10 Table 1. Acronyms and Abbreviations (cont.) DS453PP2 EP7209 1.2 Units of Measurement Symbol Unit of Measure °C degree Celsius Hz hertz (cycle per second) kbits/s kilobits per second kbyte kilobyte (1,024 bytes) kHz kilohertz kΩ kilohm Mbps megabits (1,048,576 bits) per second Mbyte megabyte (1,048,576 bytes) MHz megahertz (1,000 kilohertz) µA microampere µF microfarad µW microwatt µs microsecond (1,000 nanoseconds) mA milliampere mW milliwatt ms millisecond (1,000 microseconds) ns nanosecond V volt W watt Table 2. Unit of Measurement 1.3 General Conventions Hexadecimal numbers are presented with all letters in uppercase and a lowercase ‘h’ appended or with a 0x at the beginning. For example, 0x14 and 03CAh are hexadecimal numbers. Binary numbers are enclosed in single quotation marks when in text (for example, ‘11’ designates a binary number). Numbers not indicated by an ‘h’, 0x or quotation marks are decimal. Registers are referred to by acronym, as listed in the tables on the previous page, with bits listed in brackets MSB-to-LSB separated by a colon (:) (for example, CODR[7:0]), or LSB-to-MSB separated by a hyphen (for example, CODR[0–2]). The use of ‘tbd’ indicates values that are ‘to be determined’, ‘n/a’ designates ‘not available’, and ‘n/c’ indicates a pin that is a ‘no connect’. 1.4 Pin Description Conventions Abbreviations used for signal directions are listed in Table 3. Abbreviation Direction I Input O Output I/O Input or Output Table 3. Pin Description Conventions DS453PP2 11 EP7209 2. PIN INFORMATION 208-Pin LQFP Pin Diagram 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 NURESET NMEDCHG/NBROM NPOR BATOK NEXTPWR NBATCHG D[7] VSSIO A[7] D[8] A[8] D[9] A[9] D[10] A[10] D[11] VSSIO VDDIO A[11] D[12] A[12] D[13] A[13] D[14] A[14] D[15] A[15] D[16] A[16] D[17] A[17] NTRST VSSIO VDDIO D[18] A[18] D[19] A[19] D[20] A[20] VSSIO D[21] A[21] D[22] A[22] D[23] A[23] D[24] VSSIO VDDIO A[24] HALFWORD 2.1 EP7209 208-Pin LQFP (Top View) 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 D[25] A[25] D[26] A[26] D[27] A[27] VSSIO D[28] D[29] D[30] D[31] BUZ COL[0] COL[1] TCLK VDDIO COL[2] COL[3] COL[4] COL[5] COL[6] COL[7] FB[0] VSSIO FB[1] SMPCLK ADCOUT ADCCLK DRIVE[0] DRIVE[1] VDDIO VSSIO VDDCORE VSSCORE NADCCS ADCIN SSIRXFR SSIRXDA SSITXDA SSITXFR VSSIO SSICLK PD[0]/LEDFLSH PD[1] PD[2] PD[3] TMS VDDIO PD[4] PD[5] PD[6] PD[7] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 NCS[5] VDDIO VSSIO EXPCLK WORD WRITE RUN/CLKEN EXPRDY TXD[2] RXD[2] TDI VSSIO PB[7] PB[6] PB[5] PB[4] PB[3] PB[2] PB[1]/PRDY[2] PB[0]/PRDY[1] VDDIO TDO PA[7] PA[6] PA[5] PA[4] PA[3] PA[2] PA[1] PA[0] LEDDRV TXD[1] VSSIO PHDIN CTS RXD[1] DCD DSR NTEST[1] NTEST[0] EINT[3] NEINT[2] NEINT[1] NEXTFIQ PE[2]/CLKSEL PE[1]BOOTSEL[1] PE[0]BOOTSEL[0] VSSRTC RTCOUT RTCIN VDDRTC N/C VDDOSC MOSCIN MOSCOUT VSSOSC WAKEUP NPWRFL A[6] D[6] A[5] D[5] VDDIO VSSIO A[4] D[4] A[3] D[3] A[2] VSSIO D[2] A[1] D[1] A[0] D[0] VSSCORE VDDCORE VSSIO VDDIO CL[2] CL[1] FRM M DD[3] DD[2] VSSIO DD[1] DD[0] N/C N/C N/C N/C VDDIO VSSIO N/C N/C NMWE NMOE VSSIO NCS[0] NCS[1] NCS[2] NCS[3] NCS[4] Notes: 1)For package specifications, please see 208--Pin LQFP Package Outline Drawing on page 117 2)N/C should not be grounded but left as no connects Figure 1. 208-Pin LQFP (Low Profile Quad Flat Pack) Pin Diagram 12 DS453PP2 EP7209 2.2 Pin Descriptions Table 4 describes the function of all the external signals to the EP7209. Note that all output signals are tristateable to enable the Hi-Z test modes to be supported. 2.2.1 External Signal Functions Function Signal Name Signal Description Data bus D[0:31] I/O 32-bit system data bus for memory and I/O interface A[0:27] O 28 bits of system byte address during memory and expansion cycles Whenever the EP7209 is in the Standby State, the external address and data buses are driven low. The RUN signal is used internally to force these buses to be driven low. This is done to prevent peripherals that are powered-down from draining current. Also, the internal peripheral’s signals get set to their Reset State. Address bus nMOE O Memory output enable, active low nMWE O Memory write enable, active low nCS[0:3] O Chip select; active low, SRAM-like chip selects for expansion nCS[4:5] O Chip select; active low, CS for expansion or for CL-PS6700 select EXPRDY I Expansion port ready; external expansion devices drive this low to extend the bus cycle. This is used to insert wait states for an external bus cycle. WRITE O Write strobe, low during reads, high during writes from the EP7209 To do write accesses of different sizes Word and Half-Word must be externally decoded. The encoding of these signals is as follows: Memory Interface WORD/ HALFWORD O EXPCLK I/O Access Size Word Half-Word Word Half-Word Byte 1 * 0 0 1 0 The core will generate an address. When doing a read, the ARM core will select the appropriate byte channels. When doing a write, the correct bytes will have to be enabled depending on the above signals and the least significant bits of the address bus. The ARM architecture does not support unaligned accesses. For a read using x 32 memory, it is assumed that you will ignore bits 1 and 0 of the address bus and perform a word read (or in power critical systems decode the relevant bits depending on the size of the access). If an unaligned read takes place, the core will rotate the resulting data in the register. For more information on this behavior see the LDR instruction in the ARM7TDMI data sheet. Expansion clock rate is the same as the CPU clock for 13 MHz and 18 MHz. It runs at 36.864 MHz for 36,49 and 74 MHz modes; in 13 MHz mode this pin is used as the clock input. Table 4. External Signal Functions DS453PP2 13 EP7209 Function Signal Name Signal Description nMEDCHG/ nBROM I Media changed input; active low, deglitched. Used as a general purpose FIQ interrupt during normal operation. It is also used on power up to configure the processor to either boot from the internal Boot ROM, or from external memory. When low, the chip will boot from the internal Boot ROM. nEXTFIQ I External active low fast interrupt request input EINT[3] I External active high interrupt request input nEINT[1:2] I Two general purpose, active low interrupt inputs nPWRFL1 I Power fail input; active low, deglitched input to force system into the Standby State BATOK1 I Main battery OK input; falling edge generates a FIQ, a low level in the Standby State inhibits system start up; deglitched input nEXTPWR I External power sense; must be driven low if the system is powered by an external source nBATCHG1 I New battery sense; driven low if battery voltage falls below the "no-battery" threshold; it is a deglitched input Interrupts Power Management nPOR I Power-on reset input. This signal is not deglitched. When active it completely resets the entire system, including all the RTC registers. Upon power-up, the signal must be held active low for a minimum of 100 µsec after Vdd has settled. During normal operation, nPOR needs to be held low for at least one clock cycle of the selected clock speed (i.e., when running at 13 MHz, the pulse width of nPOR needs to be > 77 nsec). Note that nURESET, RUN/CLKEN, TEST(0), TEST(1), PE(0), PE(1), PE(2), DRIVE(0), DRIVE(1), DD(0), DD(1), DD(2), and DD(3) are all latched on rising edge of nPOR. State Control I/O This pin is programmed to either output the RUN signal or the CLKEN signal. The CLKENSL bit is used to configure this pin. When RUN is selected, the pin will be high when the system is active or idle, low while in the Standby State. When CLKEN is selected, the pin will only be driven low when in the Standby State (For RUN, see Table 6). I Wake up deglitched input signal; rising edge forces system into the Operating State from the Standby State; active after an nPOR reset. The wakeup signal can not be used to exit Idle, only Standby. Wakeup must wait at least 2 seconds before it goes high for it to be detected by the CPU. It must also be held high for at least 125 µsec to guarantee its detection. Toggling wakeup after its first detection has no effect (i.e., it is ignored). nURESET1 I User reset input; active low deglitched input from user reset button. This pin is also latched upon the rising edge of nPOR and read along with the input pins nTEST[0:1] to force the device into special test modes. nURESET does not reset the RTC. SSICLK I/O RUN/CLKEN WAKEUP1 DAI, Codec or SSI2 Interface (See Table 5 for SSI2/Codec/DAI Pin Multiplexing) DAI/Codec/SSI2 clock signal SSITXFR I/O DAI/Codec/SSI2 serial data output frame/synchronization pulse output SSITXDA O DAI/Codec/SSI2 serial data output SSIRXDA I SSIRXFR I/O DAI/Codec/SSI2 serial data input SSI2 serial data input frame/synchronization pulse DAI external clock input Table 4. External Signal Functions (cont.) 14 DS453PP2 EP7209 Function ADC Interface (SSI1) IrDA and RS232 Interfaces LCD Keyboard & Buzzer drive LED Flasher General Purpose I/O PWM Drives Signal Name Signal Description ADCCLK O Serial clock output nADCCS O Chip select for ADC interface ADCOUT O Serial data output ADCIN I Serial data input SMPCLK O Sample clock output LEDDRV O Infrared LED drive output (UART1) PHDIN I Photo diode input (UART1) TXD[1:2] O RS232 UART1 and 2 TX outputs RXD[1:2] I RS232 UART1 and 2 RX inputs DSR I RS232 DSR input DCD I RS232 DCD input CTS I RS232 CTS input DD[0:3] I/O LCD serial display data; pins can be used on power up to read the ID of some LCD modules (See Table 6). CL[1] O LCD line clock CL[2] O LCD pixel clock FRM O LCD frame synchronization pulse output M O LCD AC bias drive COL[0:7] O Keyboard column drives (SYSCON1) BUZ O Buzzer drive output (SYSCON1) PD[0]/ LEDFLSH O LED flasher driver — multiplexed with Port D bit 0. This pin can provide up to 4 mA of drive current. PA[0:7] I/O Port A I/O (bit 6 for boot clock option, bit 7 for CL-PS6700 PRDY input); also used as keyboard row inputs PB[0]/PRDY1 PB[1]/PRDY2 PB[2:7] I/O Port B I/O. All eight Port B bits can be used as GPIOs. When the PC CARD1 or 2 control bits in the SYSCON2 register are deasserted, PB[0] and PB[1] are available for GPIO. When asserted, these port bits are used as the PRDY signals for connected CL-PS6700 PC Card Host Adapter devices. PD[0:7] I/O Port D I/O PE[0]/ BOOTSEL[0] I/O Port E I/O (3 bits only). Can be used as general purpose I/O during normal operation. PE[1]/ BOOTSEL[1] I/O During power-on reset, PE[0] and PE[1] are inputs and are latched by the rising edge of nPOR to select the memory width that the EP7209 will use to read from the boot code storage device (i.e., external 8-bit-wide FLASH bank). PE[2]/ CLKSEL I/O During power-on reset, PE[2] is latched by the rising edge of nPOR to select the clock mode of operation (i.e., either the PLL or external 13 MHz clock mode). DRIVE[0:1] I/O PWM drive outputs. These pins are inputs on power up to determine what polarity the output of the PWM should be when active. Otherwise, these pins are always an output (See Table 6). FB[0:1] I PWM feedback inputs Table 4. External Signal Functions (cont.) DS453PP2 15 EP7209 Function Boundary Scan Test Signal Name Signal Description TDI I JTAG data in TDO O JTAG data out TMS I JTAG mode select TCLK I JTAG clock nTRST I JTAG async reset nTEST[0:1] I Test mode select inputs. These pins are used in conjunction with the power-on latched state of nURESET to select between the various device test models. MOSCIN MOSCOUT I O Main 3.6864 MHz oscillator for 18.432 MHz–73.728 MHz PLL RTCIN RTCOUT I O Real Time Clock 32.768 kHz oscillator Oscillators No connects N/C No connects should be left as no connects; do not connect to ground Table 4. External Signal Functions (cont.) 1. All deglitched inputs are via the 16.384 kHz clock. Each deglitched signal must be held active for at least two clock periods. Therefore, the input signal must be active for at least ~125 µs to be detected cleanly. NOTE: 2.2.2 The RTC crystal must be populated for the device to function properly. SSI/Codec/DAI Pin Multiplexing SSI2 Codec DAI Direction Strength SSICLK PCMCLK SCLK I/O 1 SSITXFR PCMSYNC LRCK I/O 1 1 SSITXDA PCMOUT SDOUT Output SSIRXDA PCMIN SDIN Input SSIRXFR p/u* MCLK I/O * 1 p/u = use an ~10 k pull-up The selection between SSI2 and the codec is controlled by the state of the SERSEL bit in SYSCON2 (See SYSCON2 System Control Register 2). The choice between the SSI2, codec, and the DAI is controlled by the DAISEL bit in SYSCON3 (See SYSCON3 System Control Register 3). Table 5. SSI/Codec/DAI Pin Multiplexing 16 DS453PP2 EP7209 2.2.3 Output Bi-Directional Pins RUN The RUN pin is looped back in to skew the address and data bus from each other. Drive [0:1] Drive 0 and 1 are looped back in on power up to determine what polarity the output of the PWM should be when active. DD[3:0] DD[3:0] are looped back in on power up to enable the reading of the ID of some LCD modules. NOTE: The above output pins are implemented as bi-directional pins to enable the output side of the pad to be monitored and hence provide more accurate control of timing or duration: Table 6. Output Bi-Directional Pins DS453PP2 17 EP7209 3. FUNCTIONAL DESCRIPTION • Digital Audio Interface (DAI) for connection to CD-quality DACs and codecs. • Interrupt controller • Advanced system state control and power management. • Two full-duplex 16550A compatible UARTs with 16-byte transmit and receive FIFOs. The EP7209 contains the following functional blocks: • IrDA SIR protocol controller capable of speeds up to 115.2 kbps. • ARM720T processor which consists of the following functional sub-blocks: • Programmable 1-, 2-, or 4-bit-per-pixel LCD controller with 16-level gray scaler. - ARM7TDMI CPU core (which supports the logic for the Thumb instruction set, core debug, enhanced multiplier, JTAG, and the Embedded ICE) running at a dynamically programmable clock speed of 18 MHz, 36 MHz, 49 MHz, or 74 MHz. • Programmable frame buffer start address, allowing a system to be built using only internal SRAM for memory. • On-chip boot ROM programmed with serial load boot sequence. • Two 16-bit general purpose timer counters. Memory Management Unit (MMU) compatible with the ARM710 core (providing address translation and a 64 entry translation lookaside buffer) with added support for Windows CE. • A 32-bit Real Time Clock (RTC) and comparator. • Dedicated LED flasher pin driven from the RTC with programmable duty ratio (multiplexed with a GPIO pin). • Two synchronous serial interfaces for Microwire or SPI peripherals such as ADCs, one supporting both the master and slave mode and the other supporting only the master mode. • Full JTAG boundary scan and Embedded ICE support. • Two programmable pulse-width modulation interfaces. • An interface to one or two Cirrus Logic CLPS6700 PC Card controller devices to support two PC Card slots. The EP7209 device is a single-chip embedded controller designed to be used in low cost and ultralow-power digital audio players. Operating at 74 MHz, the EP7209 delivers approximately 66 Dhrystone 2.1 MIPS of sustained performance (74 MIPS peak). This is approximately the same as a 100 MHz Pentium-based PC. - - 8 kbytes of unified instruction and data cache with a four-way set associative cache controller. - Write buffer • 38,400 bytes (0x9600) of on-chip SRAM that can be shared between the LCD controller and general application use. • Memory interfaces for up to 6 independent 256 Mbyte expansion segments with programming wait states. • 18 27 bits of general purpose I/O - multiplexed to provide additional functionality where necessary. DS453PP2 EP7209 • • Oscillator and phase locked loop (PLL) to generate the core clock speeds of 18.432 MHz, 36.864 MHz, 49.152 MHz, and 73.728 MHz from an external 3.6864 MHz crystal, with an alternative external clock input (used in 13 MHz mode). A low power 32.768 kHz oscillator. The EP7209 design is optimized for low power dissipation and is fabricated on a fully static 0.25 micron CMOS process. It is available in a 256-ball PBGA or a 208-pin LQFP package. Figure 2 shows a simplified block diagram of the EP7209. All external memory and peripheral devices are connected to the 32-bit data bus using the external 28-bit address bus and control signals. 3.1 CPU Core The ARM720T consists of an ARM7TDMI 32-bit RISC processor, a unified cache, and a memory management unit (MMU). The cache is four-way set associative with 8-kbytes organized as 512 lines of 4 words. The cache is directly connected to the ARM7TDMI, and therefore caches the virtual address from the CPU. When the cache misses, the MMU translates the virtual address into a physical address. A 64-entry translation lookaside buffer (TLB) is utilized to speed the address translation process and reduce bus traffic necessary to read the page table. The MMU saves power by only translating the cache misses. See the ARM720T Data sheet for a complete description of the various logic blocks that make up the processor, as well as all internal register information. 13-MHZ INPUT 3.6864 MHZ INTERNAL DATA BUS PLL D[0:31] ARM720T 32.768 KHZ 32.768-KHZ OSCILLATOR ARM7TDMI CPU CORE NPOR, RUN, RESET, WAKEUP STATE CONTROL BATOK, NEXTPWR PWRFL, BATCHG POWER MANAGEMENT EINT[1:3], FIQ, MEDCHG FLASHING LED DRIVE INTERRUPT CONTROLLER PORTS A, B, D (8-BIT) PORT E (3-BIT) KEYBD DRIVERS (0:7) BUZZER DRIVE DC-TO-DC ADCCLK, ADCIN, ADCOUT, SMPCLK, ADCCS SSICLK, SSITXFR, SSITXDA, SSIRXDA, SSIRSFR MEMORY CONTROLLER 8-KBYTE CACHE CL-PS6700 INTFC. PB[0:1], NCS[4:5] EXPANSION CONTROL EXPCLK, WORD, NCS[0:3], EXPRDY, WRITE MMU WRITE BUFFER INTERNAL ADDRESS BUS RTC LCD DMA GPIO TIMER COUNTERS (2) PWM ON-CHIP BOOT ROM SSI1 (ADC) DAI CODEC EPB BUS ICE-JTAG LCD CONTROLLER ON-CHIP SRAM 38,400 BYTES EPB BRIDGE SSI2 A[0:27], DRA[0:12] TEST AND DEVELOPMENT LCD DRIVE IrDA LED AND PHOTODIODE UART1 ASYNC INTERFACE 1 UART2 ASYNC INTERFACE 2 Figure 2. EP7209 Block Diagram DS453PP2 19 EP7209 3.2 State Control 3.2.1 The EP7209 supports the following Power Management States: Operating, Idle, and Standby (see Figure 3). The normal program execution state is the Operating State; this is a full performance state where all of the clocks and peripheral logic are enabled. The Idle State is the same as the Operating State with the exception of the CPU clock being halted, and an interrupt or wakeup will return it back to the Operating State. The Standby State has the lowest power consumption, selecting this mode shuts down the main oscillator, leaving only the Real Time Clock and its associated logic powered. It is important when the EP7209 is in Standby that all power and ground pins remain connected to power and ground in order to have a proper system wake-up. The only state that Standby can transition to is the Operating State. Interrupt or rising wakeup Standby Operating Write to standby location, power fail, or user reset te In nPOR, power fail, or user reset pt rru Write to halt location Idle Figure 3. State Diagram In the description below, the RUN/CLKEN pin can be used either for the RUN functionality, or the CLKEN functionality to allow an external oscillator to be disabled in the 13 MHz mode. Either RUN or CLKEN functionality can be selected according to the state of the CLKENSL bit in the SYSCON2 register. Table 7 on the following page shows peripheral status in various power management states. 20 Standby State The Standby State equates to the system being switched "off" (i.e., no display, and the main oscillator is shut down). When the 18.432–73.72 MHz mode is selected, the PLL will be shut down. In the 13 MHz mode, if the CLKENSL bit is set low, then the CLKEN signal will be forced low and can, if required, be used to disable an external oscillator. In the Standby State, all the system memory and state is maintained and the system time is kept upto-date. The PLL/on-chip oscillator or external oscillator is disabled and the system is static, except for the low power watch crystal (32 kHz) oscillator and divider chain to the RTC and LED flasher. The RUN signal is driven low and this signal can be used externally in the system to power down other system modules. Whenever the EP7209 is in the Standby State, the external address and data buses are forced low internally by the RUN signal. This is done to prevent peripherals that are powered-down from draining current. Also, the internal peripheral’s signals get set to their Reset State. When first powered, or reset by the nPOR (Power On Reset, active low) signal, the EP7209 is forced into the Standby State. This is known as a cold reset, and when leaving the Standby State after a cold reset, external wake up is the only way to wake up the device. When leaving the Standby State after non-cold reset conditions (i.e., the software has forced the device into the Standby State), the transition to the Operating State can be caused by a rising edge on the WAKEUP input signal or by an enabled interrupt. Normally, when entering the Standby State from the Operating State, the software will leave some interrupt sources enabled. NOTE: The CPU cannot be awakened by the TINT, WEINT, and BLINT interrupts when in the Standby State. DS453PP2 EP7209 Address (W/B) Operating Idle Standby nPOR RESET nURESET RESET UARTs On On Off Reset Reset LCD FIFO On On Reset Reset Reset LCD On On Off Reset Reset ADC Interface On On Off Reset Reset SSI2 Interface On On Off Reset Reset DAI Interface On On Off Reset Reset Codec On On Off Reset Reset Timers On On Off Reset Reset RTC On On On On On LED Flasher On On On Reset Reset DC-to-DC On On Off Reset Reset CPU On Off Off Reset Reset Interrupt Control On On On Reset Reset PLL/CLKEN Signal On On Off Off Off Table 7. Peripheral Status in Different Power Management States Typically, software writes to the Standby internal memory location to cause the transition from the Operating State to the Standby State. Before entering the Standby State, if external I/O devices (such as the CL-PS6700s connected to nCS[4] or nCS[5]) are in use, the software must check to ensure that they are idle before issuing the write to the Standby State location. Before entering the Standby State, the software must properly disable the DAI. Failing to do so will result in higher than expected power consumption in the Standby State, as well as unpredictable operation of the DAI. The DAI can be re-enabled after transitioning back to the Operating State. The system can also be forced into the Standby State by hardware if the nPWRFL or nURESET inputs are forced low. The only exit from the Standby State is to the Operating State. The system will only transition to the Operating State from the Standby State under the following conditions: when the nPWRFL input pin is high and either the nEXTPWR input pin is low or the BATOK input pin is high. This prevents the system from starting when the power supply is inadequate (i.e., the main batteries are low), corresponding to a low level on nPWRFL or BATOK. From the Standby State, if the WAKEUP signal is applied with no clock except the 32 kHz clock running, the EP7209 will be initialized into a state where it is ready to start and is waiting for the CPU to start receiving its clock. The CPU will still be held in reset at this point. After the first clock is applied, there will be a delay of about eight clock cycles before the CPU is enabled. This delay is to allow the clock to the CPU time to settle. 3.2.1.1 UART in Standby State During the Standby State, the UARTs are disabled and cannot detect any activity (i.e., start bit) on the receiver. If this functionality is required then this can be accomplished in software by the following method: DS453PP2 21 EP7209 1) Permanently connect the RX pin to one of the active low external interrupt pins. ter (refer to the SYSCON2 Register Description for details). 2) Ensure that on entry to the Standby State, the chosen interrupt source is not masked, and the UART is enabled. • If the KBWEN bit (SYSCON2 bit 3) is set low, then a keypress will cause a transition from a power saving state only if the keyboard interrupt is non-masked (i.e., the interrupt mask register 2 (INTMR2 bit 0) is high). • When KBWEN is high, a keypress will cause the device to wake up regardless of the state of the interrupt mask register. This is called the “Keyboard Direct Wakeup’ mode. In this mode, the interrupt request may not get serviced. If the interrupt is masked (i.e., the interrupt mask register 2 (INTMR2 bit 0) is low), the processor simply starts re-executing code from where it left off before it entered the power saving state. If the interrupt is non-masked, then the processor will service the interrupt. • When the KBD6 bit (SYSCON2 bit 1) is low, all 8 of Port A inputs are OR’ed together to produce the internal wakeup signal and keyboard interrupt request. This is the default reset state. • When the KBD6 bit (SYSCON2 bit 1) is high, only the lowest 6 bits of Port A are OR’ed together to produce the internal wakeup signal and keyboard interrupt request. The two most significant bits of Port A are available as GPIO when this bit is set high. 3) Send a preamble that consists of one start bit, 8 bits of zero, and one stop bit. This will cause the EP7209 to wake and execute the enabled interrupt vector. The UART will automatically be re-enabled when the processor re-enters the Operating State, and the preamble will be received. Since the UART was not awake at the start of the preamble, the timing of the sample point will be offcenter during the preamble byte. However, the next byte transmitted will be correctly aligned. Thus, the actual first real byte to be received by the UART will get captured correctly. 3.2.2 Idle State If in the Operating State, the Idle State can be entered by writing to a special internal memory location (HALT) in the EP7209. If an interrupt occurs, the EP7209 will return immediately back to the Operating State and execute the next instruction. The WAKEUP signal can not be used to exit the Idle State. It is only used to exit the Standby State. In the Idle State, the device functions just like it does when in the Operating State. However, the CPU clock is halted while it waits for an event such as a key press to generate an interrupt. The PLL (in 18.432–73.728 MHz mode) or the external 13 MHz clock source always remains active in the Idle State. 3.2.3 Keyboard Interrupt In the case where KBWEN is low and the INTMR2 bit 0 is low, it will only be possible to wakeup the device by using the external WAKEUP pin or another enabled interrupt source. The keyboard interrupt capability allows an OS to use either a polled or interrupt-driven keyboard routine, or a combination of both. For the case of the keyboard interrupt, the following options are available and are selectable according to bits 1 and 3 of the SYSCON2 regis- 22 DS453PP2 EP7209 NOTE: 3.3 The keyboard interrupt is NOT deglitched. Resets There are three asynchronous resets to the EP7209: nPOR, nPWRFL and nURESET. If any of these are active, a system reset is generated internally. This will reset all internal registers in the EP7209 except the RTC data and match registers. These registers are only cleared by nPOR allowing the system time to be preserved through a user reset or power fail condition. Any reset will also reset the CPU and cause it to start execution at the reset vector when the EP7209 returns to the Operating State. Internal to the EP7209, three different signals are used to reset storage elements. These are nPOR, nSYSRES and nSTBY. nPOR is an external signal. nSTBY is equivalent to the external RUN signal. nPOR (Power On Reset, active low) is the highest priority reset signal. When active (low), it will reset all storage elements in the EP7209. nPOR active forces nSYSRES and nSTBY active. nPOR will only be active after the EP7209 is first powered up and not during any other resets. nPOR active will clear all flags in the status register except for the cold reset flag (CLDFLG) bit, which is set. nSYSRES (System Reset, active low) is generated internally to the EP7209 if nPOR, nPWRFL or nURESET are active. It is the second highest priority reset signal, used to asynchronously reset most internal registers in the EP7209. nSYSRES active forces nSTBY and RUN low. nSYSRES is used to reset the EP7209 and force it into the Standby State with no co-operation from software. The CPU is also reset. The nSTBY and RUN signals are high when the EP7209 is in the Operating or Idle States and low when in the Standby State. The main system clock is valid when nSTBY is high. The nSTBY signal will disable any peripheral block that is clocked from the master clock source (i.e., everything ex- cept for the RTC). In general, a system reset will clear all registers and nSTBY will disable all peripherals that require a main clock. The following peripherals are always disabled by a low level on nSTBY: two UARTs and IrDA SIR encoder, timer counters, telephony codec, and the two SSI interfaces. In addition, when in the Standby State, the LCD controller and PWM drive are also disabled. When operating from an external 13 MHz oscillator which has become disabled in the Standby State by using the CLKEN signal (i.e., with CLKENSL = 0), the oscillator must be stable within 0.125 sec from the rising edge of the CLKEN signal. 3.4 Clocks There are two clocking modes for the EP7209. Either an external clock input can be used or the onchip PLL. The clock source is selected by a strapping option on Port E, pin 2 (PE[2]). If PE[2] is high at the rising edge of nPOR (i.e., upon powerup), the external clock mode is selected. If PE[2] is low, then the on-chip PLL mode is selected. After power-up, PE[2] can be used as a GPIO. The EP7209 device contains several separate sections of logic, each clocked according to its own clock frequency requirements. When the EP7209 is in external clock mode, the actual frequencies at the peripherals will be different than when in PLL mode. See each peripheral device section for more details. The section below describes the clocking for both the ARM720T and address/data bus. 3.4.1 On-Chip PLL The ARM720T clock can be programmed to 18.432 MHz, 36.864 MHz, 49.152 MHz or 73.728 MHz with the PLL running at twice the highest possible CPU clock frequency (147.456 MHz). The PLL uses an external 3.6864 MHz crystal. By chip default, the on-chip PLL is used and configured such that the ARM720T and address/data buses run at 18.432 MHz. DS453PP2 23 EP7209 When the clock frequency is selected to be 36 MHz, both the ARM720T and the address/data buses are clocked at 36 MHz. When the clock frequency is selected higher than 36 MHz, only the ARM720T gets clocked at this higher speed. The address/data will be fixed at 36 MHz. The clock frequency used is selected by programming the CLKCTL[1:0] bits in the SYSCON3 register. The clock frequency selection does not effect the EPB. Therefore, all the peripheral clocks are fixed, regardless of the clock speed selected for the ARM720T. NOTE: After modifying the CLKCTL[1:0] bits, the next instruction should always be a ‘NOP’. 3.4.1.1 Characteristics of the PLL Interface When connecting a crystal to the on-chip PLL interface pins (i.e. MOSCIN and MOSCOUT), the crystal and circuit should conform to the following requirements: • The 3.6864 MHz frequency should be created by the crystals fundamental tone (i.e., it should be a fundamental mode crystal). • A start-up resistor is not necessary, since one is provided internally. • Start-up loading capacitors may be placed on each side of the external crystal and ground. Their value should be in the range of 10 pF. However, their values should be selected based 24 upon the crystal specifications. The total sum of the capacitance of the traces between the EP7209’s clock pins, the capacitors, and the crystal leads should be subtracted from the crystal’s specifications when determining the values for the loading capacitors. • The crystal should have a maximum 100 ppm frequency drift over the chip’s operating temperature range. Alternatively, a digital clock source can be used to drive the MOSCIN pin of the EP7209. With this approach, the voltage levels of the clock source should match that of the Vdd supply for the EP7209’s pads (i.e. the supply voltage level used to drive all of the non-Vdd core pins on the EP7209). The output clock pin (i.e., MOSCOUT) should be left floating. 3.4.2 External Clock Input (13 MHz) An external 13 MHz crystal oscillator can be used to drive all of the EP7209. When selected the ARM720T and the address/data buses both get clocked at 13 MHz. The fixed clock sources to the various peripherals will have different frequencies than in the PLL mode. In this configuration, the PLL will not be used at all. NOTE: When operating at 13 MHz, the CLKCTL[1:0] bits should not be changed from their default value of ‘00’. DS453PP2 EP7209 13 MHz CLKEN Figure 4. CLKEN Timing Entering the Standby State EXPCLK (internal) RUN CLKEN Interrupt / WAKEUP Figure 5. CLKEN Timing Entering the Standby State DS453PP2 25 EP7209 3.4.3 Dynamic Clock Switching When in the PLL Clocking Mode The clock frequency used for the CPU and the buses is controlled by programming the CLKCTL[1:0] bits in the SYSCON3 register. When this occurs, the state controller switches from the current to the new clock frequency as soon as possible without causing a glitch on the clock signals. The glitchfree clock switching logic waits until the clock that is currently in use and the newly programmed clock source are both low, and then switches from the previous clock to the new clock without a glitch on the clocks. 3.5 Interrupt Controller When unexpected events arise during the execution of a program (i.e., interrupt or memory fault) an exception is usually generated. When these exceptions occur at the same time, a fixed priority system determines the order in which they are handled. Table 8 shows the priority order of all the exceptions. Priority Exception Highest Reset . Data Abort . FIQ . IRQ . Prefetch Abort Lowest Undefined Instruction, Software Interrupt Table 8. Exception Priority Handling The EP7209 interrupt controller has two interrupt types: interrupt request (IRQ) and fast interrupt request (FIQ). The interrupt controller has the ability to control interrupts from 22 different FIQ and IRQ sources. Of these, seventeen are mapped to the IRQ input and five sources are mapped to the FIQ input. 26 FIQs have a higher priority than IRQs. If two interrupts are received from within the same group (IRQ or FIQ), the order in which they are serviced must be resolved in software. The priorities are listed in Table 9. All interrupts are level sensitive; that is, they must conform to the following sequence. 1) The interrupting device (either external or internal) asserts the appropriate interrupt. 2) If the appropriate bit is set in the interrupt mask register, then either a FIQ or an IRQ will be asserted by the interrupt controller. (A description for each bit in this register can be found in INTSR1 Interrupt Status Register 1). 3) If interrupts are enabled the processor will jump to the appropriate address. 4) Interrupt dispatch software reads the interrupt status register to establish the source(s) of the interrupt and calls the appropriate interrupt service routine(s). 5) Software in the interrupt service routine will clear the interrupt source by some action specific to the device requesting the interrupt (i.e., reading the UART RX register). The interrupt service routine may then re-enable interrupts, and any other pending interrupts will be serviced in a similar way. Alternately, it may return to the interrupt dispatch code, which can check for any more pending interrupts and dispatch them accordingly. The “End of Interrupt” type interrupts are latched. All other interrupt sources (i.e., external interrupt source) must be held active until its respective service routine starts executing. See ‘End of Interrupt’ Locations for more details. Table 9, Table 10 and Table 11 show the names and allocation of interrupts in the EP7209. DS453PP2 EP7209 Interrupt Bit in INTMR1 and INTSR1 Name Comment FIQ 0 EXTFIQ FIQ 1 BLINT Battery low interrupt FIQ 2 WEINT Tick Watchdog expired interrupt FIQ 3 MCINT Media changed interrupt IRQ 4 CSINT Codec sound interrupt IRQ 5 EINT1 External interrupt input 1 (nEINT[1] pin) IRQ 6 EINT2 External interrupt input 2 (nEINT[2] pin) IRQ 7 EINT3 External interrupt input 3 (EINT[3] pin) IRQ 8 TC1OI TC1 underflow interrupt IRQ 9 TC2OI TC2 underflow interrupt IRQ 10 RTCMI RTC compare match interrupt IRQ 11 TINT IRQ 12 UTXINT1 Internal UART1 transmit FIFO empty interrupt IRQ 13 URXINT1 Internal UART1 receive FIFO full interrupt IRQ 14 UMSINT Internal UART1 modem status changed interrupt IRQ 15 SSEOTI Synchronous serial interface 1 end of transfer interrupt External fast interrupt input (nEXTFIQ pin) 64 Hz tick interrupt Table 9. Interrupt Allocation in the First Interrupt Register Interrupt Bit in INTMR2 and INTSR2 Name Comment IRQ 0 KBDINT Key press interrupt IRQ 1 SS2RX Master/slave SSI 16 bytes received IRQ 2 SS2TX Master/slave SSI 16 bytes transmitted IRQ 12 UTXINT2 UART2 transmit FIFO empty interrupt IRQ 13 URXINT2 UART2 receive FIFO full interrupt Table 10. Interrupt Allocation in the Second Interrupt Register Interrupt Bit in INTMR3 and INTSR3 Name FIQ 0 DAIINT Comment DAI interface interrupt Table 11. Interrupt Allocation in the Third Interrupt Register DS453PP2 27 EP7209 3.5.1 3.5.1.1 Interrupt Latencies in Different States Operating State The ARM720T processor checks for a low level on its FIQ and IRQ inputs at the end of each instruction. The interrupt latency is therefore directly related to the amount of time it takes to complete execution of the current instruction when the interrupt condition is detected. First, there is a one to two clock cycle synchronization penalty. For the case where the EP7209 is operating at 13 MHz with a 16-bit external memory system, and instruction sequence stored in one wait state FLASH memory, the worst case interrupt latency is 251 clock cycles. This includes a delay for cache line fills for instruction prefetches, and a data abort occurring at the end of the LDM instruction, and the LDM being non-quad word aligned. In addition, the worst-case interrupt latency assumes that LCD DMA cycles to support a panel size of 320 x 240 at 4 bits-per-pixel, 60 Hz refresh rate, is in progress. This would give a worst-case interrupt latency of about 19.3 µs for the ARM720T processor operating at 13 MHz in this system. For those interrupt inputs which have de-glitching, this figure is increased by the maximum time required to pass through the deglitcher, which is approximately 125 µs (2 cycle of the 16.384 kHz clock derived from the RTC oscillator). This would create an absolute worst case latency of approximately 141 µs. If the ARM720T is run at 36 MHz or greater and/or 32 bit wide external memory, the 19.3 µs value will be reduced. All the serial data transfer peripherals included in the EP7209 (except for the master-only SSI1) have local buffering to ensure a reasonable interrupt latency response requirement for the OS of 1 ms or less. This assumes that the maximum data rates described in this specification are complied with. If 28 the OS cannot meet this requirement, there will be a risk of data over/underflow occurring. Idle State When leaving the Idle State as a result of an interrupt, the CPU clock is restarted after approximately two clock cycles. However, there is still potentially up to 20 µsec latency as described in the first section above, unless the code is written to include at least two single cycle instructions immediately after the write to the IDLE register (in which case the latency drops to a few microseconds). This is important, as the Idle State can only be left because of a pending interrupt, which has to be synchronized by the processor before it can be serviced. 3.5.1.2 Standby State In the Standby State, the latency will depend on whether the system clock is shut down and if the FASTWAKE bit in the SYSCON3 register is set. If the system is configured to run from the internal PLL clock, then the PLL will always be shut down when in the Standby State. In this case, if the FASTWAKE bit is cleared, then there will be a latency of between 0.125 sec to 0.25 sec. If the FASTWAKE bit is set, then there will be a latency of between 250 µsec to 500 µsec. If the system is running from the external clock (at 13 MHz), with the CLKENSL bit in SYSCON2 set to 0, then the latency will also be between 0.125 sec and 0.25 sec to allow an external oscillator to stabilize. In the case of a 13 MHz system where the clock is not disabled during the Standby State (CLKENSL = 1), then the latency will be the same as described in the Idle State section above. Whenever the EP7209 is in the Standby State, the external address and data buses are driven low. The RUN signal is used internally to force these buses to be driven low. This is done to prevent peripherals that are power-down from draining current. Also, the internal peripheral’s signals get set to their Reset State. DS453PP2 EP7209 Table 12 summarizes the five external interrupt sources and the effect they have on the processor interrupts. 3.6 EP7209 Boot ROM The 128 bytes of on-chip Boot ROM contain a instruction sequence that initializes the device and then configures UART1 to receive 2048 bytes of serial data that will then be placed in the on-chip SRAM. Once the download is complete, execution jumps to the start of the on-chip SRAM. This would allow, for example, code to be downloaded to program system FLASH during a product’s manufacturing process. See Appendix A: Boot Code for details of the ROM Boot Code with comments to describe the stages of execution. Selection of the Boot ROM option is determined by the state of the nMEDCHG pin during a power on reset. If nMEDCHG is high while nPOR is active, then the EP7209 will boot from an external memory device connected to CS[0] (normal boot mode). If nMEDCHG is low, then the boot will be from the on-chip ROM. Note that in both cases, following the de-assertion of power on reset, the EP7209 will be in the Standby State and requires a low-to-high transition on the external WAKEUP pin in order to actually start the boot sequence. The effect of booting from the on-chip Boot ROM is to reverse the decoding for all chip selects internally. Table 13 shows this decoding. The control signal for the boot option is latched by nPOR, which means that the remapping of addresses and bus widths will continue to apply until nPOR is asserted again. After booting from the Boot ROM, the contents of the Boot ROM can be read back from address 0x00000000 onwards, and in normal state of operation the Boot ROM contents can be read back from address range 0x70000000. Address Range Chip Select 0000.0000–0FFF.FFFF CS[7] (Internal only) 1000.0000–1FFF.FFFF CS[6] (Internal only) 2000.0000–2FFF.FFFF nCS[5] 3000.0000–3FFF.FFFF nCS[4] 4000.0000–4FFF.FFFF nCS[3] 5000.0000–5FFF.FFFF nCS[2] 6000.0000–6FFF.FFFF nCS[1] 7000.0000–7FFF.FFFF nCS[0] Table 13. Chip Select Address Ranges After Boot From On-Chip Boot ROM Interrupt Pin Input State Operating State Latency Idle State Latency Standby State Latency nEXTFIQ Not deglitched; must be Worst case latency active for 20 µs to be of 20 µsec detected Worst case 20 µsec: if only single cycle instructions, less than 1 µsec Including PLL/osc. settling time, approx. 0.25 sec when FASTWAKE = 0, or approx. 500 µsec when FASTWAKE = 1, or = Idle State if in 13 MHz mode with CLKENSL set nEINT1–2 Not deglitched Worst case latency of 20 µsec As above As above EINT3 Not deglitched Worst case latency of 20 µsec As above As above nMEDCHG Deglitched by 16 kHz Worst case latency clock; must be active of 141 µsec for at least 125 µs to be detected Worst case 80 µsec: if only single cycle instructions, 125 µsec As above (note difference if in 13 MHz mode with CLKENSL set) Table 12. External Interrupt Source Latencies DS453PP2 29 EP7209 3.7 Memory and I/O Expansion Interface Six separate linear memory or expansion segments are decoded by the EP7209, two of which can be reserved for two PC Card cards, each interfacing to a separate single CL-PS6700 device. Each segment is 256 Mbytes in size. Two additional segments (i.e., in addition to these six) are dedicated to the on-chip SRAM and the on-chip ROM. The on-chip ROM space is fully decoded, and the SRAM space is fully decoded up to the maximum size of the video frame buffer programmed in the LCDCON register (128 kbytes). Beyond this address range the SRAM space is not fully decoded (i.e., any accesses beyond 128 kbyte range get wrapped around to within 128 kbyte range). Any of the six segments are configured to interface to a conventional SRAM-like interface, and can be individually programmed to be 8-, 16-, or 32-bits wide, to support page mode access, and to execute from 1 to 8 wait states for non-sequential accesses and 0 to 3 for burst mode accesses. The zero wait state sequential access feature is designed to support burst mode ROMs. For writable memory devices which use the nMWE pin, zero wait state sequential accesses are not permitted and one wait state is the minimum which should be programmed in the sequential field of the appropriate MEMCFG register. Bus cycles can also be extended using the EXPRDY input signal. Page mode access is accomplished by setting SQAEN = 1, which enables accesses of the form one random address followed by three sequential addresses, etc., while keeping nCS asserted. These sequential bursts can be up to four words long be- 30 fore nCS is released to allow DMA and refreshes to take place. This can significantly improve bus bandwidth to devices such as ROMs which support page mode. When SQAEN = 0, all accesses to memory are by random access without nCS being de-asserted between accesses. Again nCS is de-asserted after four consecutive accesses to allow DMAS. Bits 5 and 6 of the SYSCON2 register independently enable the interfaces to the CL-PS6700 (PC Card slot drivers). When either of these interfaces are enabled, the corresponding chip select (nCS4 and/or nCS5) becomes dedicated to that CL-PS6700 interface. The state of SYSCON2 bit 5 determines the function of chip select nCS4 (i.e., CL-PS6700 interface or standard chip select functionality); bit 6 controls nCS5 in a similar way. There is no interaction between these bits. For applications that require a display buffer smaller than 38,400 bytes, the on-chip SRAM can be used as the frame buffer. The width of the boot device can be chosen by selecting values of PE[1] and PE[0] during power on reset. These inputs are latched by the rising edge of nPOR to select the boot option. PE[1] PE[0] Boot Block (nCS0) 0 0 32-bit 0 1 8-bit 1 0 16-bit 1 1 Undefined Table 14. Boot Options DS453PP2 EP7209 3.8 CL-PS6700 PC Card Controller Interface Two of the expansion memory areas are dedicated to supporting up to two CL-PS6700 PC Card controller devices. These are selected by nCS4 and nCS5 (once enabled by bits 5 and 6 of SYSCON2). For efficient, low power operation, both address and data are carried on the lower 16 bits of the EP7209 data bus. Accesses are initiated by a write or read from the area of memory allocated for nCS4 or nCS5. The memory map within each of these areas is segmented to allow different types of PC Card accesses to take place, for attribute, I/O, and common memory space. The CL-PS6700 internal registers are memory mapped within the address space as shown in Table 15. NOTE: It must be noted that, due to the operating speed of the CL-PS6700, this interface is supported only for processor speeds of 13 and 18 MHz. A complete description of the protocol and AC timing characteristics can be found in the CL-PS6700 data sheet. A transaction is initiated by an access to the nCS4 or nCS5 area. The chip select is asserted, and on the first clock, the upper 10 bits of the PC Card address, along with 6 bits of size, space, and slot information are put out onto the lower 16 bits of the EP7209’s data bus. Only word (i.e., 4-byte) and single-byte accesses are supported, and the slot field is hardcoded to 11, since the slot field is defined as a ‘Reserved field’ by the CL-PS6700. The Access Type chip selects are used to select the device to be accessed. The space field is made directly from the A26 and A27 CPU address bits, according to the decode shown in Table 16. The size field is forced to 11 if a word access is required, or to 00 if a byte access is required. This avoids the need to configure the interface after a reset. On the second clock cycle, the remaining 16 bits of the PC Card address are multiplexed out onto the lower 16 bits of the data bus. If the transaction selected is a CL-PS6700 register transaction, or a write to the PC Card (assuming there is space available in the CL-PS6700’s internal write buffer) then the access will continue on the following two clock cycles. During these following two clock cycles the upper and lower halves of the word to be read or written will be put onto the lower 16 bits of the main data bus. The ‘ptype’ signal on the CL-PS6700s should be connected to the EP7209’s WRITE output pin. During PC Card accesses, the polarity of this pin changes and it becomes low to signify a write and high to signify a read. It is valid with the first half word of the address. During the second half word of the address it is always forced high to indicate to the CL-PS6700 that the EP7209 has initiated either the write or read. The PRDY signals from each of the two CLPS6700 devices are connected to Port B bits 0 and 1, respectively. When the PC CARD1 or PC CARD2 control bits in the SYSCON2 register are Addresses for CL-PS6700 Interface 1 Addresses for CL-PS6700 Interface 2 Attribute 0x40000000–0x43FFFFFF 0x50000000– 0x53FFFFFF I/O 0x44000000–0x47FFFFFF 0x54000000–0x57FFFFFF Common memory 0x48000000–0x4BFFFFFF 0x58000000–0x5BFFFFFF CL-PS6700 registers 0x4C000000–0x4FFFFFFF 0x5C000000–0x5FFFFFFF Table 15. CL-PS6700 Memory Map DS453PP2 31 EP7209 de-asserted, these port bits are available for GPIO. When asserted, these port bits are used as the PRDY signals. When the PRDY signal is de-asserted (i.e., low), it indicates that the CL-PS6700 is busy accessing its card. If a PC CARD access is attempted while the device is busy, the PRDY signal will cause the EP7209’s CPU to be stalled. The EP7209’s CPU will have to wait for the card to become available. DMA transfers to the LCD can still continue in the background during this period of time (as described below). The EP7209 can access the registers in the CL-PS6700, regardless of the state of the PRDY signal. If the EP7209 needs to access the PC CARD via the CL-PS6700, it waits until the PRDY signal is high before initiating a transfer request. Once a request is sent, the PRDY signal indicates if data is available. In the case of a PC Card write, writes can be posted to the CL-PS6700 device, with the same timing as CL-PS6700 internal register writes. Writes will normally be completed by the CL-PS6700 device independent of the EP7209 processor activity. If a posted write times out, or fails to complete for any other reason, then the CL-PS6700 will issue an interrupt (i.e., a WR_FAIL interrupt). In the case where the CL-PS6700 write buffer is already full, the PRDY signal will be de-asserted (i.e., driven low) and the transaction will be stalled pending an available slot in the buffer. In this case, the EP7209’s CPU will be stalled until the write can be posted successfully. While the PRDY signal is deasserted, the chip select to the CL-PS6700 will be de-asserted and the main bus will be released so that DMA transfers to the LCD controller can continue in the background. In the case of a PC Card read, the PRDY signal from the CL-PS6700 will be de-asserted until the read data is ready. At this point, it will be reasserted and the access will be completed in the same way as for a register access. In the case of a byte access, only one 16-bit data transfer will be required to complete the access. While the PRDY signal is deasserted, the chip select to the CL-PS6700 will be de-asserted and the main bus will be released so that DMA transfers to the LCD controller can continue in the background. The EP7209 will re-arbitrate for control of the bus when the PRDY signal is reasserted to indicate that the read or write transaction can be completed. The CPU will always be stalled until the PC Card access is completed. A card read operation may be split into a request cycle and a data cycle, or it may be combined into a single request/data transfer cycle. This depends on whether the data requested from the card is available in the prefetch buffer (internal to the CLPS6700). The request portion of the cycle, for a card read, is similar to the request phase for a card write (described above). If the requested data is available in the prefetch buffer, the CL-PS6700 asserts the PRDY signal before the rising edge of the third clock and the EP7209 continues the cycle to read the data. Otherwise, the PRDY signal is de-asserted and the request cycle is stalled. The EP7209 may Space Field Value PC CARD Memory Space 00 Attribute 01 I/O 10 Common memory 11 CL-PS6700 registers Table 16. Space Field Decoding 32 DS453PP2 EP7209 then allow the DMA address generator to gain control of the bus, to allow LCD refreshes to continue. When the CL-PS6700 is ready with the data, it asserts the PRDY signal. The EP7209 then arbitrates for the bus and, once the request is granted, the suspended read cycle is resumed. The EP7209 resumes the cycle by asserting the appropriate chip select, and data is transferred on the next two clocks if a word read (one clock if a byte read). There is no support within the EP7209 for detecting time-outs. The CL-PS6700 device must be programmed to force the cycle to be completed (with invalid data for a read) and then generate an interrupt if a read or write access has timed out (i.e., RD_FAIL or WR_FAIL interrupt). The system software can then determine which access was not successfully completed by reading the status registers within the CL-PS6700. The CL-PS6700 has support for DMA data transfers. However, DMA is supported only by software emulation because the DMA address generator built into the EP7209 is dedicated to the LCD controller interface. If DMA is enabled within the CLPS6700, it will assert its PDREQ signal to make a DMA request. This can be connected to one of the EP7209’s external interrupts and be used to interrupt the CPU so that the software can service the DMA request under program control. Each of the CL-PS6700 devices can generate an interrupt PIRQ. The PIRQ output is open drain on the CL-PS6700 devices, so if there are two CL-PS6700 devices they may be wire OR’ed to the same interrupt which can be connected to one of the EP7209’s active low external interrupt sources. On the receipt of an interrupt, the CPU can read the interrupt status registers on the CL-PS6700 devices to determine the cause of the interrupt. All transactions are synchronized to the EXPCLK output from the EP7209 in 18.432 MHz mode or the external 13 MHz clock. The EXPCLK should be permanently enabled, by setting the EXCKEN bit in the SYSCON1 register, when the CL-PS6700 is used. The reason for this is that the PC Card interface and CL-PS6700 internal write buffers need to be clocked after the EP7209 has completed its bus cycles. A GPIO signal from the EP7209 can be connected to the PSLEEP pin of the CL-PS6700 devices to allow them to be put into a power saving state before the EP7209 enters the Standby State. It is essential that the software monitor the appropriate status registers within the CL-PS6700s to ensure that there are no pending posted bus transactions before the Standby State is entered. Failure to do this will result in incomplete PC Card accesses. 3.9 Endianness The EP7209 uses a Little Endian configuration for internal registers. However, it is possible to connect the device to a Big Endian external memory system. The Big-endian/Little-endian bit in the ARM720T control register sets whether the EP7209 treats words in memory as being stored in Big Endian or Little Endian format. Memory is viewed as a linear collection of bytes numbered upwards from zero. Bytes 0 to 3 hold the first stored word, bytes 4 to 7 the second, and so on. In the Little Endian scheme, the lowest numbered byte in a word is considered to be the least significant byte of the word and the highest numbered byte is the most significant. Byte 0 of the memory system should be connected to data lines 7 through 0 (D[7:0]) in this scheme. In the Big Endian scheme the most significant byte of a word is stored at the lowest numbered byte, and the least significant byte is stored at the highest numbered byte. Therefore, Byte 0 of the memory system should be connected to data lines 31 through 24 (D[31:24]). Load and store are the only instructions affected by the Endianness. Tables 17 and 18 demonstrate the behavior of the EP7209 in Big and Little Endian mode, including the effect of performing non-aligned word access- DS453PP2 33 EP7209 es. The register definition section of this specification defines the behavior of the internal EP7209 registers in the Big Endian mode in more detail. For further information, refer to ARM Application Note 61, Big and Little Endian Byte Addressing. 3.10 Internal UARTs (Two) and SIR Encoder The EP7209 contains two built-in UARTs that offers similar functionality to National Semiconductor’s 16C550A device. Both UARTs can support bit rates of up to 115.2 kbits/s and include two 16byte FIFOs: one for receive and one for transmit. One of the UARTs (UART1) supports the three modem control input signals CTS, DSR and DCD. The additional RI input, and RTS and DTR output modem control lines are not explicitly supported but can be implemented using GPIO ports in the EP7209. UART2 has only the RX and TX pins. UART operation and line speeds are controlled by the UBLCR1 (UART bit rate and line control). Three interrupts can be generated by UART1: RX, TX, and modem status interrupts. Only two can be generated by UART2: RX and TX. The RX interrupt is asserted when the RX FIFO becomes half full or if the FIFO is non-empty for longer than three character length times with no more characters being received. The TX interrupt is asserted if the TX FIFO buffer reaches half empty. The modem status interrupt for UART1 is generated if any of the modem status bits change state. Framing and parity errors are detected as each byte is received and pushed onto the RX FIFO. An overrun error generates an RX interrupt immediately. All error bits can be read from the 11-bit wide data register. The FIFOs can also be programmed to be one byte depth only (i.e., like a conventional 16450 UART with double buffering). The EP7209 also contains an IrDA (Infrared Data Association) SIR protocol encoder as a post-processing stage on the output of UART1. This encod- 34 er can be optionally switched in to the TX and RX signals of UART1, so that these can be used to drive an infrared interface directly. If the SIR protocol encoder is enabled, the UART TXD1 line is held in the passive state and transitions of the RXD1 line will have no effect. The IrDA output pin is LEDDRV, and the input from the photodiode is PHDIN. Modem status lines will cause an interrupt (which can be masked) irrespective of whether the SIR interface is being used. Both the UARTs operate in a similar manner to the industry standard 16C550A. When CTS is deasserted on the UART, the UART does not stop shifting the data. It relies on software to take appropriate action in response to the interrupt generated. Baud rates supported for both the UARTs are dependent on frequency of operation. When operating from the internal PLL, the interface supports various baud rates from 115.2 kbps downwards. The master clock frequency is chosen so that most of the required data rates are obtainable exactly. When operating with a 13.0 MHz external clock source, the baud rates generated will have a slight error, which is less than or equal to 0.75%. The rates obtainable from the 13 MHz clock include 9.6 k, 19.2 k, 38 k, 58 k and 115.2 kbps. See UBRLCR1-2 UART1-2 Bit Rate and Line Control Registers for full details of the available bit rates in the 13 MHz mode. 3.11 Serial Interfaces In addition to the two UARTs, the EP7209 offers the following serial interfaces shown in Table 19. The inputs/outputs of three of the serial interfaces (DAI, codec, and SSI2) are multiplexed onto a single set of external interface pins. If the DAISEL bit of SYSCON3 is low, then either SSI2 or the codec interface will be selected to connect to the external pins. When bit 0 of SYSCON2 (SERSEL) is high, then the codec is connected to the external pins, when low the master/slave SSI2 is connected to DS453PP2 EP7209 these pins. When the DAISEL bit is set high, the DAI interface is connected to the external pins. On power up, both the DAISEL and SERSEL bits are reset low, thus the master/slave SSI2 will be connected to these pins (and configured for slave mode operation to avoid external drive clashes). Type Comments Table 20 contains pin definition information for the three multiplexed interfaces. The internal names given to each of the three interfaces are unique to help differentiate them from each other. The sections below that describe each of the three interfaces will use their respective unique internal pin names for clarity. Referred To As Max. Transfer Speed SPI/Microwire 1 Master mode only ADC Interface 128 kbits/s SPI/Microwire 2 Master/slave mode SSI2 Interface 512 kbits/s DAI Interface CD quality DACs and ADCs DAI Interface 1.536 Mbits/s Codec Interface Only for use in the PLL clock mode Codec Interface 64 kbits/s Table 19. Serial Interface Options Pin No. LQFP External Pin Name 63 SSICLK 65 SSI2 Slave Mode (Internal Name) SSI2 Master Mode Codec Internal Name DAI Internal Name Strength SSICLK = serial bit clock; Input Output PCMCLK = Output SCLK = Output 1 SSITXFR SSKTXFR = TX frame sync; Input Output PCMSYNC = Output LRCK = Output 1 66 SSITXDA SSITXDA = TX data; Output Output PCMOUT = Output SDOUT = Output 1 67 SSIRXDA SSIRXDA = RX data; Input Input PCMIN = Input SDIN = Input 68 SSIRXFR SSIRXFR = RX frame sync; Input Output p/u (use a 10k pull-up) MCLK 1 Table 20. Serial-Pin Assignments DS453PP2 35 EP7209 3.11.1 NOTE: Codec Sound Interface Both the CDENRX and CDENTX enable bits should be asserted in tandem for data to be transmitted or received. The reason for this is that the interrupt generation will occur 1 msec after one of the FIFOs is enabled. For example: If the receive FIFO gets enabled first and the transmit FIFO at a later time, the interrupt will occur 1 msec after the receive FIFO is enabled. After the first interrupt occurs, the receive FIFO will be half full. However, it will not be possible to know how full the transmit FIFO will be since it was enabled at a later time. Thus, it is possible to unintentionally overwrite data already in the transmit FIFO (See Figure 6). The codec interface allows direct connection of a telephony type codec to the EP7209. It provides all the necessary clocks and timing pulses and performs a parallel to serial conversion or vice versa on the data stream to or from the external codec device. The interface is full duplex and contains two separate data FIFOs (16 deep by 8-bits wide, one for the receive data, another for the transmit data). Data is transferred to or from the codec at 64 kbits/s. The data is either written to or read from the appropriate 16 byte FIFO. If enabled, a codec interrupt (CSINT) will be generated after every 8 bytes are transferred (FIFO half full/empty). This means the interrupt rate will be every 1 msec, with a latency of 1 msec. Transmit and receive modes are enabled by asserting high both the CDENRX and CDENTX codec enable bits in the SYSCON1 register. After the CDENRX and CDENTX enable bits get asserted, the corresponding FIFOs become enabled. When both FIFOs are disabled, the FIFO status flag CRXFE is set and CTXFF is cleared so that the FIFOs appear empty. Additionally, if the CDENTX bit is low, the PCMOUT output is disabled. Asserting either of the two enable bits causes the sync and interrupt generation logic to become active; otherwise they are disabled to conserve power. CDENRX CDENTX CSINT 1 ms Interrupt occurs Interrupt occurs 1 ms Interrupt occurs 1 ms Figure 6. Codec Interrupt Timing 36 DS453PP2 EP7209 Data is loaded into the transmit FIFO by writing to the CODR register. At the beginning of a transmit cycle, this data is loaded into a shift/load register. Just prior to the byte being transferred out, PCMSYNC goes high for one PCMCLK cycle. Then the data is shifted out serially to PCMOUT, MSB first, (with the MSB valid at the same time PCMSYNC is asserted). Data is shifted on the rising edge of the PCMCLK output. Receiving of data is performed by taking data in serially through PCMIN, again MSB first, shifting it through the shift/load register and loading the complete byte into the receive FIFO. If there is no data available in the transmit FIFO, then a zero will be loaded into the shift/load register. Input data is sampled on the falling edge of PCMCLK. Data is read from the CODR register. 3.11.2 Digital Audio Interface The DAI interface provides a high quality digital audio connection to DAI compatible audio devices. The DAI is a subset of I2S audio format that is supported by a number of manufacturers. The DAI interface produces one 128-bit frame at the audio sample frequency using a bit clock and frame sync signal. Digital audio data is transferred, full duplex, via separate transmit and receive data lines. The bit clock frequency is either fixed at 9.216 MHz or set via an externally supplied MCLK signal. The DAI interface contains separate transmit and receive FIFO’s. The transmit FIFO’s are 8 audio samples deep and the receive FIFO’s are 12 audio samples deep. DAI ADC SCLK LRCK SDATA 7209 SDIN MCLK DAI DAC SCLK LRCK SDOUT MCLK SCLK LRCK SDATA MCLK CLOCK GEN Figure 7. DAI Interface DS453PP2 37 EP7209 3.11.2.1 DAI Operation Following reset, the DAI logic is disabled. To enable the DAI, the applications program should first clear the emergency underflow and overflow status bits, which are set following the reset, by writing a 1 to these register bits (in the DAISR register). Next, the DAI control register should be programmed with the desired mode of operation using a word write. The transmit FIFOs can either be “primed” by writing up to eight 16-bit values each, or can be filled by the normal interrupt service routine which handles the DAI FIFOs. Finally, the FIFOs for each channel must be enabled via writes to DAIDR2. At this point, transmission/reception of data begins on the transmit (SDOUT) and receive (SDIN) pins. This is synchronously controlled by the 9.216 MHz (6.5 MHz in 13 MHz mode) internal clock or the externally supplied bit clock (SCLK), and the serial frame clock (LRCK). tions from low to high the next 16-bits make up the right side of an audio sample. 3.11.2.3 DAI Signals MCLK oversampled clock. Used as an input to the EP7209 for generating the DAI timing. This signal is also usually used as an input to a DAC/ADC as an oversampled clock. This signal is fixed at 256 times the audio sample frequency. SCLK bit clock. Used as the bit clock input into the DAC/ADC. This signal is fixed at 128 times the audio sample frequency. LRCK frame sync. Used as a frame synchronization input to the DAC/ADC. This signal is fixed at the audio sample frequency. This signal is clocked out on the negative going edge of SCLK. SDOUT digital audio data out. Used for sending playback data to a DAC. This signal is clocked out on the negative going edge of the SCLK output. SDIN digital audio input. Used for receiving record data from an ADC. This signal is latched by the EP7209 on the positive going edge of SCLK. 3.11.2.2 DAI Frame Format Each DAI frame is 128 bits long and is comprises one audio sample. Of this 128-bit frame, only 32 bits are actually used for digital audio data. The remaining bits are output as zeros. The LRCK signal is used as a frame synchronization signal. Each transition of LRCK delineates the left and right halves of an audio sample. When LRCK transitions from high to low the next 16-bits make up the left side of an audio sample. When LRCK transi- 128 SCLKs Left Channel LRCK Right Channel SCLK SDATA O MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 SDATAI MSB -1 -2 -3 -4 -5 +5 +4 +3 +2 +1 LSB MSB -1 -2 -3 -4 +5 +4 +3 +2 +1 LSB LSB Figure 8. EP7209 Rev C - Digital Audio Interface Timing – MSB/Left Justified format 38 DS453PP2 EP7209 3.11.3 ADC Interface — Master Mode Only SSI1 (Synchronous Serial Interface) The first synchronous serial interface allows interfacing to the following peripheral devices: • In the default mode, the device is compatible with the MAXIM MAX148/9 in external clock mode. Similar SPI or Microwire compatible devices can be connected directly to the EP7209. • In the extended mode and with negative-edge triggering selected (the ADCCON and ADCCKNSEN bits are set, respectively, in the SYSCON3 register), this device can be interfaced to Analog Devices’ AD7811/12 chip using nADCCS as a common RFS/TFS line. • Other features of the devices, including power management, can be utilized by software and the use of the GPIO pins. The clock output frequency is programmable and only active during data transmissions to save power. There are four output frequencies selectable, which will be slightly different depending whether the device is operating in a 13 MHz mode or a 18.432 MHz–73.728 MHz mode (see Table 21). The required frequency is selected by programming the corresponding bits 16 and 17 in the SYSCON1 register. The sample clock (SMPCLK) always runs at twice the frequency of the shift clock (ADCCLK). The output channel is fed by an 8-bit shift register when the ADCCON bit of SYSCON3 is clear. When ADCCON is set, up to 16 bits of configuration command can be sent, as specified in the SYNCIO register. The input channel is captured by a 16-bit shift register. The clock and synchronization pulses are activated by a write to the output shift register. During transfers the SSIBUSY (synchronous serial interface busy) bit in the system status flags register is set. When the transfer is complete and valid data is in the 16-bit read shift register, the SSEOTI interrupt is asserted and the SSIBUSY bit is cleared. An additional sample clock (SMPCLK) can be enabled independently and is set at twice the transfer clock frequency. This interface has no local buffering capability and is only intended to be used with low bandwidth interfaces, such as for a touch-screen ADC interface. 3.11.4 Master/Slave SSI2 Serial Interface 2) (Synchronous A second SPI/Microwire interface with full master/slave capability is provided by the EP7209. Data rates in slave mode are theoretically up to 512 kbits/s, full duplex, although continuous operation at this data rate will give an interrupt rate of 2 kHz, which is too fast for many operating systems. This would require a worst case interrupt response time of less than 0.5 msec and would cause loss of data through TX underruns and RX overruns. SYSCON1 bit 17 SYSCON1 bit 16 13.0 MHz Operation ADCCLK Frequency (kHz) 18.432–73.728 MHz Operation ADCCLK Frequency (kHz) 0 0 4.2 4 0 1 16.9 16 1 0 67.7 64 1 1 135.4 128 Table 21. ADC Interface Operation Frequencies DS453PP2 39 EP7209 The interface is fully capable of being clocked at 512 kHz when in slave mode. However, it is anticipated that external hardware will be used to frame the data into packets. Therefore, although the data would be transmitted at a rate of 512 kbits/s, the sustained data rate would in fact only be 85.3 kbits/s (i.e., 1 byte every 750 µsec). At this data rate, the required interrupt rate will be greater than 1 msec, which is acceptable. There are separate half-word-wide RX and TX FIFOs (16 half-words each) and corresponding interrupts which are generated when the FIFO’s are half-full or half-empty as appropriate. The interrupts are called SS2RX and SS2TX, respectively. Register SS2DR is used to access the FIFOs. There are five pins to support this SSI port: SSIRXDA, SSITXFR, SSICLK, SSITXDA, and SSIRXFR. The SSICLK, SSIRXDA, SSIRXFR, and SSITXFR signals are inputs and the SSITXDA signal is an output in slave mode. In the master mode, SSICLK, SSITXDA, SSITXFR, and SSIRXFR are outputs and SSIRXDA is an input. Master mode is enabled by writing a one to the SS2MAEN bit (SYSCON2[9]). When the master/slave SSI is not required, it can be disabled to save power by writing a zero to the SS2TXEN and the SS2RXEN bits (SYSCON2[4] [7]). When set, these two bits inde- Slave 7209 pendently enable the transmit and receive sides of the interface. The master/slave SSI is synchronous, full duplex, and capable of supporting serial data transfers between two nodes. Although the interface is byteoriented, data is loaded in blocks of two bytes at a time. Each data byte to be transferred is marked by a frame sync pulse, lasting one clock period, and located one clock prior to the first bit being transferred. Direction of the SSI2 ports, in slave and master mode, is shown in Figure 9. Data on the link is sent MSB first and coincides with an appropriate frame sync pulse, of one clock in duration, located one clock prior to the first data bit sent (i.e., MSB). It is not possible to send data LSB first. When operating in master mode, the clock frequency is selected to be the same as the ADC interface’s (master mode only SSI1) — that is, the frequencies are selected by the same bits 16 and 17 of the SYSCON1 register (i.e., the ADCKSEL bits). Thus, the maximum frequency in master mode is 128 kbits/s. The interface will support continuous transmission at this rate assuming that the OS can respond to the interrupts within 1 msec to prevent over/underruns. Master 7209 SSIRXFR SSIRXFR SSITXFR SSITXFR SSICLK SSICLK SSIRXDA SSITXDA SSITXDA SSIRXDA Figure 9. SSI2 Port Directions in Slave and Master Mode 40 DS453PP2 EP7209 Address (W/B) Data in Memory (as seen by the EP7209) Byte Lanes to Memory/Ports/Registers Big Endian Memory Little Endian Memory 7:0 15:8 23:16 31:24 7:0 15:8 Word + 0 (W) 11223344 44 33 22 11 44 33 22 Word + 1 (W) 11223344 44 33 22 11 44 33 Word + 2 (W) 11223344 44 33 22 11 44 33 Word + 3 (W) 11223344 44 33 22 11 44 Word + 0 (H) 11223344 44 33 22 11 Word + 1 (H) 11223344 44 33 22 Word + 2 (H) 11223344 44 33 22 Word + 3 (H) 11223344 44 33 Word + 0 (B) 11223344 dc Word + 1 (B) 11223344 Word + 2 (B) 11223344 Word + 3 (B) 11223344 NOTE: R0 Contents 23: 16 31: 24 Big Endian Little Endian 11 11223344 11223344 22 11 44112233 44112233 22 11 33441122 33441122 33 22 11 22334411 22334411 44 33 22 11 00001122 00003344 11 44 33 22 11 22000011 44000033 11 44 33 22 11 00003344 00001122 22 11 44 33 22 11 44000033 22000011 dc dc 11 44 dc dc dc 00000011 00000044 dc dc 22 dc dc 33 dc dc 00000022 00000033 dc 33 dc dc dc dc 22 dc 00000033 00000022 44 dc dc dc dc dc dc 11 00000044 00000011 dc = don’t care Table 17. Effect of Endianness on Read Operations Address (W/B) Register Contents Byte Lanes to Memory/Ports/Registers Big Endian Memory Little Endian Memory 7:0 15:8 23:16 31:24 7:0 15:8 23:16 31:24 Word + 0 (W) 11223344 44 33 22 11 44 33 22 11 Word + 1 (W) 11223344 44 33 22 11 44 33 22 11 Word + 2 (W) 11223344 44 33 22 11 44 33 22 11 Word + 3 (W) 11223344 44 33 22 11 44 33 22 11 Word + 0 (H) 11223344 44 33 44 33 44 33 44 33 Word + 1 (H) 11223344 44 33 44 33 44 33 44 33 Word + 2 (H) 11223344 44 33 44 33 44 33 44 33 Word + 3 (H) 11223344 44 33 44 33 44 33 44 33 Word + 0 (B) 11223344 44 44 44 44 44 44 44 44 Word + 1 (B) 11223344 44 44 44 44 44 44 44 44 Word + 2 (B) 11223344 44 44 44 44 44 44 44 44 Word + 3 (B) 11223344 44 44 44 44 44 44 44 44 NOTE: Bold indicates active byte lane. Table 18. Effect of Endianness on Write Operations DS453PP2 41 EP7209 NOTE: To allow synchronization to the incoming slave clock, the interface enable bits will not take effect until one SSICLK cycle after they are written and the value read back from SYSCON2. The enable bits reflect the real status of the enables internally. Hence, there will be a delay before the new value programmed to the enable bits can be read back. The timing diagram for this interface can be found in the AC Characteristics section of this document. 3.11.4.1 Read Back of Residual Data All writes to the transmit FIFO must be in halfwords (i.e., in units of two bytes at a time). On the receive side, it is possible that an odd number of bytes will be received. Bytes are always loaded into the receive FIFO in pairs, so in the case of a single residual byte remaining at the end of a transmission, it will be necessary for the software to read the byte separately. This is done by reading the status of two bits in the SYSFLG2 register to determine the validity of the residual data. These two bits (RESVAL, RESFRM) are both set high when a residual is valid; RESVAL is cleared on either a new transmission or on reading of the residual bit by software. RESFRM is cleared only on a new transmission. By popping the residual byte into the RX FIFO and then reading the status of these bits it is possible to determine if a residual bit has been correctly read. Figure 10 illustrates this procedure. The sequence is as follows: read the RESVAL bit, if this is a 0, no action needs to be taken. If this is a 1, then pop the residual byte into the FIFO by writing to the SS2POP location. Then read back the two status bits RESVAL and RESFRM. If these bits read back 01, then the residual byte popped into the FIFO is valid and can be read back from the SS2DR register. If the bits are not 01, then there has been another transmission received since the residual read procedure has been started. The data item that has been popped to the top of the FIFO will be invalid and should be ignored. In this case, the correct byte 42 will have been stored in the most significant byte of the next half-word to be clocked into the FIFO. NOTE: All the writes/reads to the FIFO are done word at a time (data on the lower 16 bits is valid and upper 16 bits are ignored). Software manually pops the residual byte into the RX FIFO by writing to the SS2POP location (the value written is ignored). This write will strobe the RX FIFO write signal, causing the residual byte to be written into the FIFO. 3.11.4.2 Support for Asymmetric Traffic The interface supports asymmetric traffic (i.e., unbalanced data flow). This is accomplished through separate transmit and receive frame sync control lines. In operation, the receiving node receives a byte of data on the eight clocks following the assertion of the receive frame sync control line. In a similar fashion, the sending node can transmit a byte of data on the eight clocks following the assertion of the transmit frame sync pulse. There is no correlation in the frequency of assertions of the RX and TX frame sync control lines (SSITXFR and SSIRXFR). Hence, the RX path may bear a greater data throughput than the TX path, or vice versa. Both directions, however, have an absolute maximum data throughput rate determined by the maxi- Residual bit valid 00 11 New RX byte received Pop FIFO New RX byte received 01 Figure 10. Residual Byte Reading DS453PP2 EP7209 mum possible clock frequency, assuming that the interrupt response of the target OS is sufficiently quick. 3.11.4.3 Continuous Data Transfer Data bytes may be sent/received in a contiguous manner without interleaving clocks between bytes. The frame sync control line(s) are eight clocks apart and aligned with the clock representing bit D0 of the preceding byte (i.e., one bit in advance of the MSB). 3.11.4.4 Discontinuous Clock In order to save power during the idle times, the clock line is put into a static low state. The master is responsible for putting the link into the Idle State. The Idle State will begin one clock, or more, after the last byte transferred and will resume at least one clock prior to the first frame sync assertion. To disable the clock, the TX section is turned off. In Master mode, the EP7209 does not support the discontinuous clock. 3.11.4.5 Error Conditions RX FIFO overflows are detected and conveyed via a status bit in the SYSFLG2 register. This register should be accessed at periodic intervals by the application software. The status register should be read each time the RX FIFO interrupts are generated. At this time the error condition (i.e., overrun flag) will indicate that an error has occurred but cannot convey which byte contains the error. Writing to the SRXEOF register location clears the overrun flag. TX FIFO underflow condition is detected and conveyed via a bit in the SYSFLG2 register, which is accessed by the application software. A TX underflow error is cleared by writing data to be transmitted to the TX FIFO. 3.11.4.6 Clock Polarity Clock polarity is fixed. TX data is presented on the bus on the rising edge of the clock. Data is latched into the receiving device on the falling edge of the clock. The TX pin is held in a tristate condition when not transmitting. 3.12 LCD Controller with Support for OnChip Frame Buffer The LCD controller provides all the necessary control signals to interface directly to a single panel multiplexed LCD. The panel size is programmable and can be any width (line length) from 32 to 1024 pixels in 16 pixel increments. The total video frame buffer size is programmable up to 128 kbytes. This equates to a theoretical maximum panel size of 1024 x 256 pixels in 4-bits-per-pixel mode. The video frame buffer can be located in any portion of memory controlled by the chip selects. Its start address will be fixed at address 0x0000000 within each chip select. The start address of the LCD video frame buffer is defined in the FBADDR[3:0] register. These bits become the most significant nibble of the external address bus. The default start address is 0xC000 0000 (FBADDR = 0xC). A system built using the on-chip SRAM (OCSR), will then serve as the LCD video frame buffer and miscellaneous data store. The LCD video frame buffer start address should be set to 0x6 in this option. Programming of the register FBADDR is only permitted when the LCD is disabled (this is to avoid possible cycle corruption when changing the register contents while a LCD DMA cycle is in progress). There is no hardware protection to prevent this. It is necessary for the software to disable the LCD controller before reprogramming the FBADDR register. Full address decoding is provided for the OCSR, up to the maximum video frame buffer size programmable into the LCDCON register. Beyond this, the address is wrapped around. The frame buffer start address must not be programmed to 0x4 or 0x5 if either CL-PS6700 in- DS453PP2 43 EP7209 terface is in use (PCMEN1 or PCMEN2 bits in the SYSCON2 register are enabled). FBADDR should never be programmed to 0x7 or 0x8, as these are the locations for the on-chip Boot ROM and internal registers. The screen is mapped to the video frame buffer as one contiguous block where each horizontal line of pixels is mapped to a set of consecutive bytes or words in the video RAM. The video frame buffer can be accessed word wide as pixel 0 is mapped to the LSB in the buffer such that the pixels are arranged in a Little Endian manner. The pixel bit rate, and hence the LCD refresh rate, can be programmed from 18.432 MHz to 576 kHz when operating in 18.432–73.728 MHz mode, or 13 MHz to 203 kHz when operating from a 13 MHz clock. The LCD controller is programmed by writing to the LCD control register (LCDCON). The LCDCON register should not be reprogrammed while the LCD controller is enabled. The LCD controller also contains two 32-bit palette registers, which allow any 4-, 2-, or 1-bit pixel value to be mapped to any of the 15 gray scale values available. The required DMA bandwidth to support a ½ VGA panel displaying 4-bits-per-pixel data at an 80 Hz refresh rate is approximately 6.2 Mbytes/sec. Assuming the frame buffer is stored in a 32-bit wide the maximum theoretical bandwidth available is 86 Mbytes/sec at 36.864 MHz, or 29.7 Mbytes/sec at 13 MHz. The LCD controller uses a nine stage 32-bit wide FIFO to buffer display data. The LCD controller requests new data when there are five words remaining in the FIFO. This means that for a ½ VGA display at 4-bits-per-pixel and 80 Hz refresh rate, the maximum allowable DMA latency is approximately 3.25 µsec ((5 words x 8 bits/byte)/(640 x 240 x 4bpp x 80 Hz)) = 3.25 µsec). The worst-case 44 latency is the total number of cycles from when the DMA request appears to when the first DMA data word actually becomes available at the FIFO. DMA has the highest priority, so it will always happen next in the system. The maximum number of cycles required is 36 from the point at which the DMA request occurs to the point at which the STM is complete, then another 6 cycles before the data actually arrives at the FIFO from the first DMA read. This creates a total of 42 cycles. Assuming the frame buffer is located in 32-bit wide, the worst case latency is almost exactly 3.2 µs, with 13 MHz page mode cycles. With each cycle consuming ~77 ns (i.e., 1/1 MHz), the value of 3.2 µs comes from 42 cycles x 77 ns/cycle = ~3.23 µsec. If 16-bit wide, then the worst case latency will double. In this case, the maximum permissible display size will be halved, to approx. 320 x 240 pixels, assuming the same pixel depth and refresh rate has to be maintained. If the frame buffer is to be stored in static memory, then further calculations must be performed. If 18 MHz mode is selected, and 32-bit wide, then the worst case latency will be 2.26 µsec (i.e., 42 cycles x 54 nsec/cycle). If 36 MHz mode is selected, and 32-bit wide, then the worst case latency drops down to 1.49 µs. This calculation is a little more complex for 36 MHz mode of operation. The total number of cycles = (12 x 4) + 7 = 55. Thus, 55 x 27 ns = ~1.49 µsec. Figure 11 shows the organization of the video map for all combinations of bits per pixel. The refresh rate is not affected by the number of bits per pixel; however the LCD controller fetches twice the data per refresh for 4-bits-per-pixel compared to 2-bits-per-pixel. The main reason for reducing the number of bits per pixel is to reduce the power consumption of the memory where the video frame buffer is mapped. DS453PP2 EP7209 3.13 Timer Counters Two identical timer counters are integrated into the EP7209. These are referred to as TC1 and TC2. Each timer counter has an associated 16-bit read/write data register and some control bits in the system control register. Each counter is loaded with the value written to the data register immediately. This value will then be decremented on the second active clock edge to arrive after the write (i.e., after the first complete period of the clock). When the timer counter under flows (i.e., reaches 0), it will assert its appropriate interrupt. The timer counters can be read at any time. The clock source and mode are selectable by writing to various bits in the system control register. When run from the internal PLL, 512 kHz and 2 kHz rates are provided. When using the 13 MHz external source, the default frequencies will be 541 kHz and 2.115 kHz, respectively. However, only in non-PLL mode, an optional divide by 26 frequency can be generated Pixel 1 Pixel 2 Pixel 3 Pixel 4 Gray scale Bit 0 Bit 1 Gray scale Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 4 Bits per pixel Pixel 1 Pixel 2 Pixel 3 Pixel 4 Gray scale Gray scale Bit 0 Gray scale Bit 1 Bit 2 Bit 3 Bit 4 Gray scale Bit 5 Bit 6 Bit 7 2 Bits per pixel Pixel 1 Pixel 2 Pixel 3 Pixel 4 Gray scale Gray scale Gray scale Gray scale Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 1 Bit per pixel Figure 11. Video Buffer Mapping DS453PP2 45 EP7209 (thus generating a 500 kHz frequency when using the 13 MHz source). This divider is enabled by setting the OSTB (Operating System Timing Bit) in the SYSCON2 register (bit 12). When this bit is set high to select the 500 kHz mode, the 500 kHz frequency is routed to the timers instead of the 541 kHz clock. This does not affect the frequencies derived for any of the other internal peripherals. The timer counters can operate in two modes: free running or pre-scale. 3.13.1 Free Running Mode In the free running mode, the counter will wrap around to 0xFFFF when it under flows and it will continue to count down. Any value written to TC1 or TC2 will be decremented on the second edge of the selected clock. 3.13.2 Prescale Mode read twice to ensure a valid and stable reading. This also applies when reading back the RTCDIV field of the SYSCON1 register, which reflects the status of the six LSBs of the RTC counter. 3.14.1 When connecting a crystal to the RTC interface pins (i.e., RTCIN and RTCOUT), the crystal and circuit should conform to the following requirements: • The 32.768 kHz frequency should be created by the crystals fundamental tone (i.e., it should be a fundamental mode crystal) • A start-up resistor is not necessary, since one is provided internally. • Start-up loading capacitors may be placed on each side of the external crystal and ground. Their value should be in the range of 10 pF. However, their values should be selected based upon the crystal specifications. The total sum of the capacitance of the traces between the EP7209’s clock pins, the capacitors, and the crystal leads should be subtracted from the crystal’s specifications when determining the values for the loading capacitors. • The crystal should have a maximum 5 ppm frequency drift over the chip’s operating temperature range. • The voltage for the crystal must be 2.5 V + 0.2 V. In the prescale mode, the value written to TC1 or TC2 is automatically re-loaded when the counter under flows. Any value written to TC1 or TC2 will be decremented on the second edge of the selected clock. This mode can be used to produce a programmable frequency to drive the buzzer (i.e., with TC1) or generate a periodic interrupt. 3.14 Real Time Clock The EP7209 contains a 32-bit Real Time Clock (RTC). This can be written to and read from in the same way as the timer counters, but it is 32 bits wide. The RTC is always clocked at 1 Hz, generated from the 32.768 kHz oscillator. It also contains a 32-bit output match register, this can be programmed to generate an interrupt when the time in the RTC matches a specific time written to this register. The RTC can only be reset by an nPOR cold reset. Because the RTC data register is updated from the 1 Hz clock derived from the 32 kHz source, which is asynchronous to the main memory system clock, the data register should always be 46 Characteristics of the Real Time Clock Interface Alternatively, a digital clock source can be used to drive the RTCIN pin of the EP7209. With this approach, the voltage levels of the clock source should match that of the Vdd supply for the EP7209’s pads (i.e., the supply voltage level used to drive all of the non-Vdd core pins on the EP7209) (i.e., RTCOUT). The output clock pin should be left floating. DS453PP2 EP7209 3.15 Dedicated LED Flasher The LED flasher feature enables an external pin (PD[0]/LEDFLSH) to be toggled at a programmable rate and duty ratio, with the intention that the external pin is connected to an LED. This module is driven from the RTCs 32.768 kHz oscillator and works in all running modes because no CPU intervention is needed once its rate and duty ratio have been configured (via the LEDFLSH register). The LED flash rate period can be programmed for 1, 2, 3, or 4 seconds. The duty ratio can be programmed such that the mark portion can be 1/16, 2/16, 3/16, …, 16/16 of the full cycle. The external pin can provide up to 4 mA of drive current. 3.16 Boundary Scan IEEE 1149.1 compliant JTAG is provided with the EP7209. Table 22 shows what instructions are supported in the EP7209. Instruction Code To maximize power savings, the drive ratio fields should be used to disable the PWMs, instead of the FB pins. The clocks that source the PWMs are disabled when the drive ratio fields are zeroed. Description 0000 Places the selected scan chain in test mode. 0010 Connects the Scan Path Register between TDI and TDO 0011 NOTE: This instructio n i s i nc lu ded for product testing only and should never be used. 1110 Connects the ID register between TDI and TDO 1111 Connects a 1-bit shift register bit TDI and TDO EXTEST SCAN_N SAMPLE/PRELOAD Two PWM Interfaces Two Pulse Width Modulator (PWM) duty ratio clock outputs are provided by the EP7209. When the device is operating from the internal PLL, the PWM will run at a frequency of 96 kHz. These signals are intended for use as drives for external DCto-DC converters in the Power Supply Unit (PSU) subsystem. External input pins that would normally be connected to the output from comparators monitoring the external DC-to-DC converter output are also used to enable these clocks. These are the FB[0:1] pins. The duty ratio (and hence PWMs on time) can be programmed from 1 in 16 to 15 in 16. The sense of the PWM drive signal (active high or low) is determined by latching the state of this drive signal during power on reset (i.e., a pull-up on the drive signal will result in a active low drive output, and visa versa). This allows either positive or negative voltages to be generated by the external DC-to-DC converter. PWMs are disabled by writing zeros into the drive ratio fields in the PMPCON Pump Control register. NOTE: 3.17 IDCODE BYPASS Table 22. Instructions Supported in JTAG Mode The INTEST function will not be supported for the EP7209. Additional user-defined instructions exist, but these are not relevant to board-level testing. For further information please refer to the ARM DDI 0087E ARM720T Data Sheet. As there are additional scan-chains within the ARM720T processor, it is necessary to include a scan-chain select function — shown as SCAN_N in Table 22. To select a particular scan chain, this function must be input to the TAP controller, followed by the 4-bit scan-chain identification code. The identification code for the boundary scan chain is 0011. Note that it is only necessary to issue the SCAN_N instruction if the device is already in the JTAG mode. The boundary scan chain is selected as the DS453PP2 47 EP7209 by the ARM processor. Execution is halted when either a match occurs between the values programmed into the ICEBreaker and the values currently appearing on the address bus, data bus, and the various control signals. Any bit can be masked to remove it from the comparison. Either unit can be programmed as a watchpoint (monitoring data accesses) or a breakpoint (monitoring instruction fetches). default on test-logic reset and any of the system resets. The contents of the device ID-register for the EP7209 are shown in Table 23. This is equivalent to 0x0F0F0F0F. Note this is the ID-code for the ARM720T processor. 3.18 In-Circuit Emulation 3.18.1 Introduction Using one of these watchpoint units, an unlimited number of software breakpoints (in RAM) can be supported by substitution of the actual code. EmbeddedICE is an extension to the architecture of the ARM family of processors, and provides the ability to debug cores that are deeply embedded into systems. It consists of three parts: NOTE: The EXTERN[1:0] signals from the ICEBreaker module are not wired out in this device. This mechanism is used to allow watchpoints to be dependent on an external event. This behavior can be emulated in software via the ICEBreaker control registers. 1) A set of extensions to the ARM core 2) The EmbeddedICE macrocell, to provide access the extensions from the outside world 3) The EmbeddedICE interface to provide communication from the EmbeddedICE macrocell and the host computer A more detailed description is available in the ARM Software Development Toolkit User Guide and Reference Manual. The ICEBreaker module and its registers are fully described in the ARM7TDMI Data Sheet. The EmbeddedICE macrocell is programmed, in a serial fashion, through the TAP controller on the ARM via the JTAG interface. The EmbeddedICE macrocell is by default disabled to minimize power usage, and must be enabled at boot-up to support this functionality. 3.18.2 3.19 A maximum configured system using the EP7209 is shown in Figure 12. This system assumes the ROMs are 16-bit wide devices. The keyboard may be connected to more GPIO bits than shown to allow greater than 64 keys, however these extra pins will not be wired into the WAKEUP pin functionality. Functionality The ICEBreaker module consists of two real-time watchpoint units together with a control and status register. One or both of the units can be programmed to halt the execution of the instructions Version 0 0 0 Maximum EP7209-Based System Part number 0 1 1 1 1 0 0 0 0 1 1 Manufacturer ID 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 Table 23. Device ID Register 48 DS453PP2 EP7209 CRYSTAL MOSCIN DD[3:0] CRYSTAL RTCIN nCS[4] PB0 EXPCLK CL1 CL2 FM M LCD COL[7:0] CL-PS6700 PC CARD CONTROLLER PC CARD SOCKET KEYBOARD D[31:0] PA[7:0] A[27:0] PB[7:0] nMOE WRITE PD[7:0] EP7209 PE[2:0] nPOR nPWRFL BATOK nEXTPWR nBATCHG RUN WAKEUP DRIVE[1:0] FB[1:0] nCS[0] nCS[1] ×16 FLASH ×16 FLASH DAISSICLK SSITXFR SSITXDA SSIRXDA ×16 FLASH ×16 FLASH LEDDRV PHDIN CS[n] WORD EXTERNAL MEMORYMAPPED EXPANSION BUFFERS NCS[2] NCS[3] ADDITIONAL I/O NOTE: BUFFERS AND LATCHES LEDFLSH RXD1/2 TXD1/2 DSR CTS DCD ADCCLK nADCCS ADCOUT ADCIN SMPCLK POWER SUPPLY UNIT AND COMPARATORS DC INPUT BATTERY DC-TO-DC CONVERTERS CODEC/SSI2/ DAI IR LED AND PHOTODIODE 2× RS-232 TRANSCEIVERS ADC DIGITIZER A system can only use one of the following peripheral interfaces at any given time: SSI2, codec, or DAI. Figure 12. A Maximum EP7209 Based System DS453PP2 49 EP7209 4. MEMORY MAP The lower 2 GByte of the address space is allocated to memory. The 2 GByte less 8 k for internal registers is not accessible in the EP7209. The MMU in the EP7209 should be programmed to generate an abort exception for access to this area. Internal peripherals are addressed through a set of internal memory locations from hex address 8000.0000 to 8000.3FFF. These are known as the internal registers in the EP7209. In Table 24, the memory map from 0x8000.000 to 0x8000.1FFF contains registers that are compatible with the CLPS7111 (see Table 24). These were included for backward compatibility and are referred to as old internal registers. Table 24 shows how the 4-Gbyte address range of the ARM720T processor (as configured within this chip) is mapped in the EP7209. The memory map shown assumes that two CL-PS6700 PC Card controllers are connected. If this functionality is not required, then the nCS[4] and nCS[5] memory is available. The external boot ROM is not fully decoded (i.e., the boot code will repeat within the 256-Mbyte space from 0x70000000 to 0x80000000). See Table 13 on page 29 for the memory map when booted from on chip boot ROM. The SRAM is fully decoded up to a maximum size of 128 kbytes. Access to any location above this range will be wrapped to within the range. Address Contents Size 0xF000.0000 Reserved 256 Mbytes 0xE000.0000 Reserved 256 Mbytes 0xD000.0000 Unused 256 Mbytes 0xC000.0000 Unused 256 Mbytes 0x8000.4000 Unused ~1 Gbyte 0x8000.2000 Internal registers (new) 8 kbytes 0x8000.0000 Internal registers (old) (from 7111) 8 kbytes 0x7000.0000 Boot ROM (nCS[7]) 128 bytes 0x6000.0000 SRAM (nCS[6]) 38,400 bytes 0x5000.0000 PCMCIA-1 (nCS[5]) 4 x 64 Mbytes 0x4000.0000 PCMCIA-0 (nCS[4]) 4 x 64 Mbytes 0x3000.0000 Expansion (nCS[3]) 256 Mbytes 0x2000.0000 Expansion (nCS[2]) 256 Mbytes 0x1000.0000 ROM Bank 1 (nCS[1]) 256 Mbytes 0x0000.0000 ROM Bank 0 (nCS[0]) 256 Mbytes Table 24. EP7209 Memory Map in External Boot Mode 50 DS453PP2 EP7209 5. REGISTER DESCRIPTIONS 5.1 Internal Registers Table 25 shows the Internal Registers of the EP7209 that are compatible with the CL-PS7111 when the CPU is configured to a Little Endian Memory System. Table 26 shows the differences that occur when the CPU is configured to a Big Endian Memory System for byte-wide access to Ports A, B, and D. All the internal registers are inherently Little Endian (i.e., the least significant byte is attached to bits 7 to 0 of the data bus). Hence, the system Endianness affects the addresses required for byte accesses to the internal registers, resulting in a reversal of the byte address required to read/write a particular byte within a register. Note that the internal registers have been split into two groups – the “old” and the “new”. The old ones are the same as that used in CL-PS7111 and are there for compatibility. The new registers are for accessing the additional functionality of the DAI interface and the LED flasher. There is no effect on the register addresses for word accesses. Bits A[0:1] of the internal address bus are only decoded for Ports A, B, and D (to allow read/write to individual ports). For all other registers, bits A[0:1] are not decoded, so that byte reads will return the whole register contents onto the EP7209’s internal bus, from where the appropriate byte (according to the Endianness) will be read by the CPU. To avoid the additional complexity, it is preferable to perform all internal register accesses as word operations, except for ports A to D which are explicitly designed to operate with byte accesses, as well as with word accesses. An 8 k segment of memory in the range 0x8000.0000 to 0x8000.3FFF is reserved for internal use in the EP7209. Accesses in this range will not cause any external bus activity unless debug mode is enabled. Writes to bits that are not explic- itly defined in the internal area are legal and will have no effect. Reads from bits not explicitly defined in the internal area are legal but will read undefined values. All the internal addresses should only be accessed as 32-bit words and are always on a word boundary, except for the PIO port registers, which can be accessed as bytes. Address bits in the range A[0:5] are not decoded (except for Ports A–D), this means each internal register is valid for 64 bytes (i.e., the SYSFLG1 register appears at locations 0x8000.0140 to 0x8000.017C). There are some gaps in the register map for backward compatibility reasons, but registers located next to a gap are still only decoded for 64 bytes. The GPIO port registers are byte-wide and can be accessed as a word but not as a half-word. These registers additionally decode A[0:1]. All addresses are in hexadecimal notation. NOTE: All byte-wide registers should be accessed as words (except Port A to Port D registers, which are designed to work in both word and byte modes). All registers bit alignment starts from the LSB of the register (i.e., they are all right shift justified). The registers which interact with the 32 kHz clock or which could change during readback (i.e., RTC data registers, SYSFLG1 register (lower 6-bits only), the TC1D and TC2D data registers, port registers, and interrupt status registers), should be read twice and compared to ensure that a stable value has been read back. All internal registers in the EP7209 are reset (cleared to zero) by a system reset (i.e., nPOR, nRESET, or nPWRFL signals becoming active), and the Real Time Clock data register (RTCDR) and match register (RTCMR), which are only reset by nPOR becoming active. This ensures that the system time preserved through a user reset or power fail condition. In the following register descriptions, Little Endian is assumed. DS453PP2 51 EP7209 Address Name Default RD/WR Size Comments 0x8000.0000 PADR 0 RW 8 Port A data register 0x8000.0001 PBDR 0 RW 8 Port B data register 0x8000.0002 — — 8 Reserved 0x8000.0003 PDDR 0 RW 8 Port D data register 0x8000.0040 PADDR 0 RW 8 Port A data direction register 0x8000.0041 PBDDR 0 RW 8 Port B data direction register 0x8000.0042 — — 8 Reserved 0x8000.0043 PDDDR 0 RW 8 Port D data direction register 0x8000.0080 PEDR 0 RW 3 Port E data register 0x8000.00C0 PEDDR 0 RW 3 Port E data direction register 0x8000.0100 SYSCON1 0 RW 32 System control register 1 0x8000.0140 SYSFLG1 0 RD 32 System status flags register 1 0x8000.0180 MEMCFG1 0 RW 32 Expansion memory configuration register 1 0x8000.01C0 MEMCFG2 0 RW 32 Expansion memory configuration register 2 0x8000.0240 INTSR1 0 RD 32 Interrupt status register 1 0x8000.0280 INTMR1 0 RW 32 Interrupt mask register 1 0x8000.02C0 LCDCON 0 RW 32 LCD control register 0x8000.0300 TC1D 0 RW 16 Read/Write register sets and reads data to TC1 0x8000.0340 TC2D 0 RW 16 Read/Write register sets and reads data to TC2 0x8000.0380 RTCDR — RW 32 Real Time Clock data register 0x8000.03C0 RTCMR — RW 32 Real Time Clock match register 0x8000.0400 PMPCON 0 RW 12 PWM pump control register 0x8000.0440 CODR 0 RW 8 CODEC data I/O register 0x8000.0480 UARTDR1 0 RW 16 UART1 FIFO data register 0x8000.04C0 UBLCR1 0 RW 32 UART1 bit rate and line control register 0x8000.0500 SYNCIO 0 RW 32 Synchronous serial I/O data register for master only SSI 0x8000.0540 PALLSW 0 RW 32 Least significant 32-bit word of LCD palette register 0x8000.0580 PALMSW 0 RW 32 Most significant 32-bit word of LCD palette register 0x8000.05C0 STFCLR — WR — Write to clear all start up reason flags 0x8000.0600 BLEOI — WR — Write to clear battery low interrupt 0x8000.0640 MCEOI — WR — Write to clear media changed interrupt 0x8000.0680 TEOI — WR — Write to clear tick and watchdog interrupt 0x8000.06C0 TC1EOI — WR — Write to clear TC1 interrupt Table 25. EP7209 Internal Registers Compatible with CL-PS7111 (Little Endian Mode) 52 DS453PP2 EP7209 Address Name Default RD/WR Size Comments 0x8000.0700 TC2EOI — WR — Write to clear TC2 interrupt 0x8000.0740 RTCEOI — WR — Write to clear RTC match interrupt 0x8000.0780 UMSEOI — WR — Write to clear UART modem status changed interrupt 0x8000.07C0 COEOI — WR — Write to clear CODEC sound interrupt 0x8000.0800 HALT — WR — Write to enter the Idle State 0x8000.0840 STDBY — WR — Write to enter the Standby State 0x8000.0880– 0x8000.0FFF Reserved 0x8000.1000 FBADDR 0xC RW 4 LCD frame buffer start address 0x8000.1100 SYSCON2 0 RW 16 System control register 2 0x8000.1140 SYSFLG2 0 RD 16 System status register 2 0x8000.1240 INTSR2 0 RD 24 Interrupt status register 2 0x8000.1280 INTMR2 0 RW 16 Interrupt mask register 2 0x8000.12C0– 0x8000.147F Reserved 0x8000.1480 UARTDR2 0 RW 16 UART2 Data Register 0x8000.14C0 UBLCR2 0 RW 32 UART2 bit rate and line control register 0x8000.1500 SS2DR 0 RW 16 Master/slave SSI2 data Register 0x8000.1600 SRXEOF — WR — Write to clear RX FIFO overflow flag 0x8000.16C0 SS2POP — WR — Write to pop SSI2 residual byte into RX FIFO 0x8000.1700 KBDEOI — WR — Write to clear keyboard interrupt 0x8000.1800 Reserved — WR — Do not write to this location. A write will cause the processor to go into an unsupported power savings state. 0x8000.1840– 0x8000.1FFF Reserved — Write will have no effect, read is undefined Write will have no effect, read is undefined Write will have no effect, read is undefined Table 25. EP7209 Internal Registers Compatible with CL-PS7111 (Little Endian Mode) (cont.) DS453PP2 53 EP7209 Big Endian Mode Name Default RD/WR Size Comments 0x8000.0003 PADR 0 RW 8 Port A Data Register 0x8000.0002 PBDR 0 RW 8 Port B Data Register 0x8000.0001 — — 8 Reserved 0x8000.0000 PDDR 0 RW 8 Port D Data Register 0x8000.0043 PADDR 0 RW 8 Port A data Direction Register 0x8000.0042 PBDDR 0 RW 8 Port B Data Direction Register 0x8000.0041 — — 8 Reserved 0x8000.0040 PDDDR 0 RW 8 Port D Data Direction Register 0x0000.0080 PEDR 0 RW 3 Port E Data Register 0X8000.0000 PEDDR 0 RW 3 Port E Data Direction Register Table 26. EP7209 Internal Registers (Big Endian Mode) NOTE: 5.1.1 The following Register Descriptions refer to Little Endian Mode Only PADR Port A Data Register ADDRESS: 0x8000.0000 Values written to this 8-bit read/write register will be output on Port A pins if the corresponding data direction bits are set high (port output). Values read from this register reflect the external state of Port A, not necessarily the value written to it. All bits are cleared by a system reset. 5.1.2 PBDR Port B Data Register ADDRESS: 0x8000.0001 Values written to this 8-bit read/write register will be output on Port B pins if the corresponding data direction bits are set high (port output). Values read from this register reflect the external state of Port B, not necessarily the value written to it. All bits are cleared by a system reset. 5.1.3 PDDR Port D Data Register ADDRESS: 0x8000.0003 Values written to this 8-bit read/write register will be output on Port D pins if the corresponding data direction bits are set low (port output). Values read from this register reflect the external state of Port D, not necessarily the value written to it. All bits are cleared by a system reset. 5.1.4 PADDR Port A Data Direction Register ADDRESS: 0x8000.0040 Bits set in this 8-bit read/write register will select the corresponding pin in Port A to become an output, clearing a bit sets the pin to input. All bits are cleared by a system reset. 5.1.5 PBDDR Port B Data Direction Register ADDRESS: 0x8000.0041 Bits set in this 8-bit read/write register will select the corresponding pin in Port B to become an output, clearing a bit sets the pin to input. All bits are cleared by a system reset. 54 DS453PP2 EP7209 5.1.6 PDDDR Port D Data Direction Register ADDRESS: 0x8000.0043 Bits cleared in this 8-bit read/write register will select the corresponding pin in Port D to become an output, setting a bit sets the pin to input. All bits are cleared by a system reset so that Port D is output by default. 5.1.7 PEDR Port E Data Register ADDRESS: 0x8000.0080 Values written to this 3-bit read/write register will be output on Port E pins if the corresponding data direction bits are set high (port output). Values read from this register reflect the external state of Port E, not necessarily the value written to it. All bits are cleared by a system reset. 5.1.8 PEDDR Port E Data Direction Register ADDRESS: 0x8000.00C0 Bits set in this 3-bit read/write register will select the corresponding pin in Port E to become an output, clearing bit sets the pin to input. All bits are cleared by a system reset so that Port E is input by default. DS453PP2 55 EP7209 5.2 SYSTEM Control Registers 5.2.1 SYSCON1 The System Control Register 1 ADDRESS: 0x8000.0100 23 22 21 20 19 IRTXM WAKEDIS 15 14 13 12 11 SIREN CDENRX CDENTX LCDEN DBGEN 7 6 5 4 3:0 TC2S TC2M TC1S TC1M Keyboard scan The system control register is a 21-bit read/write register which controls all the general configuration of the EP7209, as well as modes etc. for peripheral devices. All bits in this register are cleared by a system reset. The bits in the system control register SYSCON1 are defined in Table 27. Bit 0:3 Description Keyboard scan: This 4-bit field defines the state of the keyboard column drives. The following table defines these states. Keyboard Scan Column 0 All driven high 1 All driven low 2–7 All high impedance (tristate) 8 Column 0 only driven high all others high impedance 9 Column 1 only driven high all others high impedance 10 Column 2 only driven high all others high impedance 11 Column 3 only driven high all others high impedance 12 Column 4 only driven high all others high impedance 13 Column 5 only driven high all others high impedance 14 Column 6 only driven high all others high impedance 15 Column 7 only driven high all others high impedance 4 TC1M: Timer counter 1 mode. Setting this bit sets TC1 to prescale mode, clearing it sets free running mode. 5 TC1S: Timer counter 1 clock source. Setting this bit sets the TC1 clock source to 512 kHz, clearing it sets the clock source to 2 kHz. 6 TC2M: Timer counter 2 mode. Setting this bit sets TC2 to prescale mode, clearing it sets free running mode. 7 TC2S: Timer counter 2 clock source. Setting this bit sets the TC2 clock source to 512 kHz, clearing it sets the clock source to 2 kHz. 8 UART1EN: Internal UART enable bit. Setting this bit enables the internal UART. Table 27. SYSCON1 56 DS453PP2 EP7209 Bit Description 9 BZTOG: Bit to drive (i.e., toggle) the buzzer output directly when software mode of operation is selected (i.e., bit BZMOD = 0). See the BZMOD and BUZFREQ (SYSCON1) bits for more details. 10 BZMOD: This bit selects the buzzer drive mode. When BZMOD = 0, the buzzer drive output pin is connected directly to the BZTOG bit. This is the software mode. When BZMOD = 1, the buzzer drive is in the hardware mode. Two hardware sources are available to drive the pin. They are the TC1 or a fixed internally generated clock source. The selection of which source is used to drive the pin is determined by the state of the BUZFREQ bit in the SYSCON2 register. If the TC1 is selected, then the buzzer output pin is connected to the TC1 under flow bit. The buzzer output pin changes every time the timer wraps around. The frequency depends on what was programmed into the timer. See the description of the BUZFREQ and BZTOG bits (SYSCON2) for more details. 11 DBGEN: Setting this bit will enable the debug mode. In this mode, all internal accesses are output as if they were reads or writes to the expansion memory addressed by nCS5. nCS5 will still be active in its standard address range. In addition the internal interrupt request and fast interrupt request signals to the ARM720T processor are output on Port E, bits 1 and 2. Note that these bits must be programmed to be outputs before this functionality can be observed. The clock to the CPU is output on Port E, Bit 0 to enable individual accesses to be distinguished. For example, in debug mode: nCS5 = nCS5 or internal I/O strobe PE0 = CLK PE1 = nIRQ PE2 = nFIQ 12 LCDEN: LCD enable bit. Setting this bit enables the LCD controller. 13 CDENTX: Codec interface enable TX bit. Setting this bit enables the codec interface for data transmission to an external codec device. 14 CDENRX: Codec interface enable RX bit. Setting this bit enables the codec interface for data reception from an external codec device. NOTE: Both CDENRX and CDENTX need to be enabled/disabled in tandem, otherwise data may be lost. 15 SIREN: HP SIR protocol encoding enable bit. This bit will have no effect if the UART is not enabled. 16:17 ADCKSEL: Microwire / SPI peripheral clock speed select. This two bit field selects the frequency of the ADC sample clock; this is twice the frequency of the synchronous serial ADC interface clock. The table below shows the available frequencies for operation when in PLL mode. These bits are also used to select the shift clock frequency for the SSI2 interface when set into master mode. The frequencies obtained in 13.0 MHz mode can be found in Table 21. ADCKSEL ADC Sample Frequency (kHz) — SMPCLK ADC Clock Frequency (kHz) — ADCCLK 00 8 4 01 32 16 10 128 64 11 256 128 Table 27. SYSCON1 (cont.) DS453PP2 57 EP7209 Bit Description 18 EXCKEN: External expansion clock enable. If this bit is set, the EXPCLK is enabled continuously; it is the same speed and phase as the CPU clock and will free run all the time the main oscillator is running if this bit is set. This bit should not be left set all the time for power consumption reasons. If the system enters the Standby State, the EXPCLK will become undefined. If this bit is clear, EXPCLK will be active during memory cycles to expansion slots that have external wait state generation enabled only. 19 WAKEDIS: Setting this bit disables waking up from the Standby State, via the wakeup input. 20 IRTXM: IrDA TX mode bit. This bit controls the IrDA encoding strategy. Clearing this bit means each zero bit transmitted is represented as a pulse of width 3/16th of the bit rate period. Setting this bit means each zero bit is represented as a pulse of width 3/16th of the period of 115,200-bit rate clock (i.e., 1.6 µsec regardless of the selected bit rate). Setting this bit will use less power, but will probably reduce transmission distances. Table 27. SYSCON1 (cont.) 58 DS453PP2 EP7209 5.2.2 SYSCON2 System Control Register 2 ADDRESS: 0x8000.1100 15 14 13 12 11:10 9 8 Reserved BUZFREQ CLKENSL OSTB Reserved SS2MAEN UART2EN 7 6 5 4 3 2 1 0 SS2RXEN PC CARD2 PC CARD1 SS2TXEN KBWEN Reserved KBD6 SERSEL This register is an extension of SYSCON1, containing additional control for the EP7209, for compatibility with CL-PS7111. The bits of this second system control register are defined below. The SYSCON2 register is reset to all 0s on power up. Bit 0 Description SERSEL:The only affect of this bit is to select either SSI2 or the codec to interface to the external pins. See the table below for the selection options. NOTE: If the DAISEL bit of SYSCON3 is set, then it overrides the state of the SERSEL bit, and thus the external pins are connected to the DAI interface. SERSEL Value Selected Serial Device to External Pins 0 Master/slave SSI2 1 Codec 1 KBD6: The state of this bit determines how many of the Port A inputs are OR’ed together to create the keyboard interrupt. When zero (the reset state), all eight of the Port A inputs will generate a keyboard interrupt. When set high, only Port A bits 0 to 5 will generate an interrupt from the keyboard. It is assumed that the keyboard row lines are connected into Port A. 3 KBWEN: When the KBWEN bit is high, the EP7209 will awaken from a power saving state into the Operating State when a high signal is on one of Port A’s inputs (irrespective of the state of the interrupt mask register). This is called the Keyboard Direct Wakeup mode. In this mode, the interrupt request does not have to get serviced. If the interrupt is masked (i.e., the interrupt mask register 2 (INTMR2) bit 0 is low), the processor simply starts re-executing code from where it left off before it entered the power saving state. If the interrupt is non-masked, then the processor will service the interrupt. 4 SS2TXEN: Transmit enable for the synchronous serial interface 2. The transmit side of SSI2 will be disabled until this bit is set. When set low, this bit also disables the SSICLK pin (to save power) in master mode, if the receive side is low. 5 PC CARD1: Enable for the interface to the CL-PS6700 device for PC Card slot 1. The main effect of this bit is to reassign the functionality of Port B, bit 0 to the PRDY input from the CL-PS6700 devices, and to ensure that any access to the nCS4 address space will be according to the CL-PS6700 interface protocol. 6 PC CARD2: Enable for the interface to the CL-PS6700 device for PC Card slot 2. The main effect of this bit is to reassign the functionality of Port B, bit 1 to the PRDY input from the CL-PS6700 devices, and to ensure that any access to the nCS5 address space will be according to the CL-PS6700 interface protocol. Table 28. SYSCON2 DS453PP2 59 EP7209 Bit Description 7 SS2RXEN: Receive enable for the synchronous serial interface 2. The receive side of SSI2 will be disabled until this bit is set. When both SSI2TXEN and SSI2RXEN are disabled, the SSI2 interface will be in a power saving state. 8 UART2EN: Internal UART2 enable bit. Setting this bit enables the internal UART2. 9 SS2MAEN: Master mode enable for the synchronous serial interface 2. When low, SSI2 will be configured for slave mode operation. When high, SSI2 will be configured for master mode operation. This bit also controls the directionality of the interface pins. 12 OSTB: This bit (operating system timing bit) is for use only with the 13 MHz clock source mode. Normally it will be set low, however when set high it will cause a 500 kHz clock to be generated for the timers instead of the 541 kHz which would normally be available. The divider to generate this frequency is not clocked when this bit is set low. 13 CLKENSL: CLKEN select. When low, the CLKEN signal will be output on the RUN/CLKEN pin. When high, the RUN signal will be output on RUN/CLKEN. 14 BUZFREQ: The BUZFREQ bit is used to select which hardware source will be used as the source to drive the buzzer output pin. When BUZFREQ = 0, the buzzer signal generated from the on-chip timer (TC1) is output. When BUZFREQ = 1, a fixed frequency clock is output (500 Hz when running from the PLL, 528 Hz in the 13 MHz external clock mode). See the BZMOD and the BZTOG bits (SYSCON2) for more details. Table 28. SYSCON2 (cont.) 60 DS453PP2 EP7209 5.2.3 SYSCON3 System Control Register 3 ADDRESS: 0x8000eeg.2200 15 14 13 12 11 10 9 8 Reserved Reserved Reserved Reserved Reserved Reserved DAIEN FASTWAKE 7 6 5 4 3 2 1 0 VERSN[2] Reserved VERSN[1] Reserved VERSN[0] Reserved ADCCKNSEN DAISEL CLKCTL1 CLKCTL0 ADCCON This register is an extension of SYSCON1 and SYSCON2, containing additional control for the EP7209. The bits of this third system control register are defined in Table 29. Bit Description 0 ADCCON: Determines whether the ADC Configuration Extension field SYNCIO(31:16) is to be used for ADC configuration data. When this bit = 0 (default state) the ADC Configuration Byte SYNCIO(7:0) only is used for compatibility with the CL-PS7111. When this bit = 1, the ADC Configuration Extension field in the SYNCIO register is used for ADC Configuration data and the value in the ADC Configuration Byte (SYNCIO(6:0)) selects the length of the data (8-bit to 16-bit). 1:2 CLKCTL(1:0): Determines the frequency of operation of the processor and Wait State scaling. The table below lists the available options. NOTE: CLKCTL(1:0) Value Processor Frequency Memory Bus Frequency Wait State Scaling 00 18.432 MHz 18.432 MHz 1 01 36.864 MHz 36.864 MHz 2 10 49.152 MHz 36.864 MHz 2 11 73.728 MHz 36.864 MHz 2 To determine the number of wait states programmed refer to Table 36 and Table 37. When operating at 13 MHz, the CLKCTL[1:0] bits should not be changed from the default value of ‘00’. Under no circumstances should the CLKCTL bits be changed using a buffered write. 3 DAIPSEL: When set selects the DAI Interface. This defaults to either the SSI (i.e., DAISEL bit is low). 4 ADCCKNSEN: When set, configuration data is transmitted on ADCOUT at the rising edge of the ADCCLK, and data is read back on the falling edge on the ADCIN pin. When clear (default), the opposite edges are used. 5:7 VERSN[0:2]: Additional read-only version bits — will read ‘000’. 8 FASTWAKE: When set, the device will wake from the Standby State within one to two cycles of a 4 kHz clock. This bit is cleared at power up, and thus the device first starts using the default one to two cycles of the 8 Hz clock. 9 DAIEN: This bit enables the Digital Audio Interface when set (i.e., when DAIEN is high). Table 29. SYSCON3 DS453PP2 61 EP7209 5.2.4 SYSFLG1 — The System Status Flags Register ADDRESS: 0x8000.0140 31:30 29 28 27 26 VERID ID BOOTBIT1 BOOTBIT0 SSIBUSY 23 22 21:16 23 22 UTXFF1 URXFE1 RTCDIV UTXFF1 URXFE1 15 14 13 12 11 CLDFLG PFFLG RSTFLG NBFLG UBUSY1 7:4 3 2 1 0 DID WUON WUDR DCDET MCDR The system status flags register is a 32-bit read only register, which indicates various system information. The bits in the system status flags register SYSFLG1 are defined in Table 30. Bit Description 0 MCDR: Media changed direct read. This bit reflects the INVERTED non-latched status of the media changed input. 1 DCDET: This bit will be set if a non-battery operated power supply is powering the system (it is the inverted state of the nEXTPWR input pin). 2 WUDR: Wake up direct read. This bit reflects the non-latched state of the wakeup signal. 3 WUON: This bit will be set if the system has been brought out of the Standby State by a rising edge on the wakeup signal. It is cleared by a system reset or by writing to the HALT or STDBY locations. 4:7 DID: Display ID nibble. This 4-bit nibble reflects the latched state of the four LCD data lines. The state of the four LCD data lines is latched by the LCDEN bit, and so it will always reflect the last state of these lines before the LCD controller was enabled. These bits identify the LCD display panel fitted. 8 CTS: This bit reflects the current status of the clear to send (CTS) modem control input to UART1. 9 DSR: This bit reflects the current status of the data set ready (DSR) modem control input to UART1. 10 DCD: This bit reflects the current status of the data carrier detect (DCD) modem control input to UART1. 11 UBUSY1: UART1 transmitter busy. This bit is set while UART1 is busy transmitting data, it is guaranteed to remain set until the complete byte has been sent, including all stop bits. 12 NBFLG: New battery flag. This bit will be set if a low to high transition has occurred on the nBATCHG input, it is cleared by writing to the STFCLR location. 13 RSTFLG: Reset flag. This bit will be set if the RESET button has been pressed, forcing the nURESET input low. It is cleared by writing to the STFCLR location. 14 PFFLG: Power Fail Flag. This bit will be set if the system has been reset by the nPWRFL input pin, it is cleared by writing to the STFCLR location. Table 30. SYSFLG 62 DS453PP2 EP7209 Bit Description 15 CLDFLG: Cold start flag. This bit will be set if the EP7209 has been reset with a power on reset, it is cleared by writing to the STFCLR location. 16:21 RTCDIV: This 6-bit field reflects the number of 64 Hz ticks that have passed since the last increment of the RTC. It is the output of the divide by 64 chain that divides the 64 Hz tick clock down to 1 Hz for the RTC. The MSB is the 32 Hz output, the LSB is the 1 Hz output. 22 URXFE1: UART1 receiver FIFO empty. The meaning of this bit depends on the state of the UFIFOEN bit in the UART1 bit rate and line control register. If the FIFO is disabled, this bit will be set when the RX holding register is empty. If the FIFO is enabled the URXFE bit will be set when the RX FIFO is empty. 23 UTXFF1: UART1 transmit FIFO full. The meaning of this bit depends on the state of the UFIFOEN bit in the UART1 bit rate and line control register. If the FIFO is disabled, this bit will be set when the TX holding register is full. If the FIFO is enabled the UTXFF bit will be set when the TX FIFO is full. 24 CRXFE: Codec RX FIFO empty bit. This will be set if the 16-byte codec RX FIFO is empty. 25 CTXFF: Codec TX FIFO full bit. This will be set if the 16-byte codec TX FIFO is full. 26 SSIBUSY: Synchronous serial interface busy bit. This bit will be set while data is being shifted in or out of the synchronous serial interface, when clear data is valid to read. 27:28 BOOTBIT0–1: These bits indicate the default (power-on reset) bus width of the ROM interface. See Memory Configuration Registers for more details on the ROM interface bus width. The state of these bits reflect the state of Port E[0:1] during power on reset, as shown in the table below. PE[1] (BOOTBIT1) PE[0] (BOOTBIT0) Boot option 0 0 32-bit 0 1 8-bit 1 0 16-bit 1 1 Reserved 29 ID: Will always read ‘1’ for the EP7209 device. 30:31 VERID: Version ID bits. These 2 bits determine the version id for the EP7209. Will read ‘10’ for the initial version. Table 30. SYSFLG (cont.) DS453PP2 63 EP7209 5.2.5 SYSFLG2 System Status Register 2 ADDRESS: 0x8000.1140 23 22 21:12 11 10:7 6 UTXFF2 URXFE2 Reserved UBUSY2 Reserved CKMODE 5 4 3 2 1 0 SS2TXUF SS2TXFF SS2RXFE RESFRM RESVAL SS2RXOF This register is an extension of SYSFLG1, containing status bits for backward compatibility with CLPS7111. The bits of the second system status register are defined in Table 31. Bit Description 0 SS2RXOF: Master/slave SSI2 RX FIFO overflow. This bit is set when a write is attempted to a full RX FIFO (i.e., when RX is still receiving data and the FIFO is full). This can be cleared in one of two ways: 1. Empty the FIFO (remove data from FIFO) and then write to SRXEOF location. 2. Disable the RX (affects of disabling the RX will not take place until a full SSI2 clock cycle after it is disabled) 1 RESVAL: Master/slave SSI2 RX FIFO residual byte present, cleared by popping the residual byte into the SSI2 RX FIFO or by a new RX frame sync pulse. 2 RESFRM: Master/slave SSI2 RX FIFO residual byte present, cleared only by a new RX frame sync pulse. 3 SS2RXFE: Master/slave SSI2 RX FIFO empty bit. This will be set if the 16 x 16 RX FIFO is empty. 4 SS2TXFF: Master/slave SSI2 TX FIFO full bit. This will be set if the 16 x 16 TX FIFO is full. This will get cleared when data is removed from the FIFO or the EP7209 is reset. 5 SS2TXUF: Master/slave SSI2 TX FIFO Underflow bit. This will be set if there is attempt to transmit when TX FIFO is empty. This will be cleared when FIFO gets loaded with data. 6 CKMODE: This bit reflects the status of the CLKSEL (PE[2]) input, latched during nPOR. When low, the PLL is running and the chip is operating in 18.432–73.728 MHz mode. When high the chip is operating from an external 13 MHz clock. 11 UBUSY2: UART2 transmitter busy. This bit is set while UART2 is busy transmitting data; it is guaranteed to remain set until the complete byte has been sent, including all stop bits. 22 URXFE2: UART2 receiver FIFO empty. The meaning of this bit depends on the state of the UFIFOEN bit in the UART2 bit rate and line control register. If the FIFO is disabled, this bit will be set when the RX holding register contains is empty. If the FIFO is enabled the URXFE bit will be set when the RX FIFO is empty. 23 UTXFF2: UART2 transmit FIFO full. The meaning of this bit depends on the state of the UFIFOEN bit in the UART2 bit rate and line control register. If the FIFO is disabled, this bit will be set when the TX holding register is full. If the FIFO is enabled the UTXFF bit will be set when the TX FIFO is full. Table 31. SYSFLG2 64 DS453PP2 EP7209 5.3 Interrupt Registers 5.3.1 INTSR1 Interrupt Status Register 1 ADDRESS: 0x8000.0240 15 14 13 12 11 10 9 8 SSEOTI UMSINT URXINT1 UTXINT1 TINT RTCMI TC2OI TC1OI 7 6 5 4 3 2 1 0 EINT3 EINT2 EINT1 CSINT MCINT WEINT BLINT EXTFIQ The interrupt status register is a 32-bit read only register. The interrupt status register reflects the current state of the first 16 interrupt sources within the EP7209. Each bit is set if the appropriate interrupt is active. The interrupt assignment is given in Table 32. Bit Description 0 EXTFIQ: External fast interrupt. This interrupt will be active if the nEXTFIQ input pin is forced low and is mapped to the FIQ input on the ARM720T processor. 1 BLINT: Battery low interrupt. This interrupt will be active if no external supply is present (nEXTPWR is high) and the battery OK input pin BATOK is forced low. This interrupt is de-glitched with a 16 kHz clock, so it will only generate an interrupt if it is active for longer than 125 µsec. It is mapped to the FIQ input on the ARM720T processor and is cleared by writing to the BLEOI location. NOTE: BLINT is disabled during the Standby State. 2 WEINT: Tick Watch dog expired interrupt. This interrupt will become active on a rising edge of the periodic 64 Hz tick interrupt clock if the tick interrupt is still active (i.e., if a tick interrupt has not been serviced for a complete tick period). It is mapped to the FIQ input on the ARM720T processor and the TEOI location NOTE: WEINT is disabled during the Standby State. Watch dog timer tick rate is 64 Hz (in 13 MHz and 73.728–18.432 MHz modes). Watchdog timer is turned off during the Standby State. 3 MCINT: Media changed interrupt. This interrupt will be active after a rising edge on the nMEDCHG input pin has been detected, This input is de-glitched with a 16 kHz clock so it will only generate an interrupt if it is active for longer than 125 µsec. It is mapped to the FIQ input on the ARM7TDMI processor and is cleared by writing to the MCEOI location. On power-up, the Media change pin (nMEDCHG) is used as an input to force the processor to either boot from the internal Boot ROM, or from external memory. After power-up, the pin can be used as a general purpose FIQ interrupt pin. 4 CSINT: Codec sound interrupt, generated when the data FIFO has reached half full or empty (depending on the interface direction). It is cleared by writing to the COEOI location. 5 EINT1: External interrupt input 1. This interrupt will be active if the nEINT1 input is active (low) it is cleared by returning nEINT1 to the passive (high) state. 6 EINT2: External interrupt input 2. This interrupt will be active if the nEINT2 input is active (low) it is cleared by returning nEINT2 to the passive (high) state. 7 EINT3: External interrupt input 3. This interrupt will be active if the EINT3 input is active (high) it is cleared by returning EINT3 to the passive (low) state. Table 32. INTSR1 DS453PP2 65 EP7209 Bit Description 8 TC1OI: TC1 under flow interrupt. This interrupt becomes active on the next falling edge of the timer counter 1 clock after the timer counter has under flowed (reached zero). It is cleared by writing to the TC1EOI location. 9 TC2OI: TC2 under flow interrupt. This interrupt becomes active on the next falling edge of the timer counter 2 clock after the timer counter has under flowed (reached zero). It is cleared by writing to the TC2EOI location. 10 RTCMI: RTC compare match interrupt. This interrupt becomes active on the next rising edge of the 1 Hz Real Time Clock (one second later) after the 32-bit time written to the Real Time Clock match register exactly matches the current time in the RTC. It is cleared by writing to the RTCEOI location. 11 TINT: 64 Hz tick interrupt. This interrupt becomes active on every rising edge of the internal 64 Hz clock signal. This 64 Hz clock is derived from the 15-stage ripple counter that divides the 32.768 kHz oscillator input down to 1 Hz for the Real Time Clock. This interrupt is cleared by writing to the TEOI location. NOTE: TINT is disabled/turned off during the Standby State. 12 UTXINT1: Internal UART1 transmit FIFO half-empty interrupt. The function of this interrupt source depends on whether the UART1 FIFO is enabled. If the FIFO is disabled (FIFOEN bit is clear in the UART1 bit rate and line control register), this interrupt will be active when there is no data in the UART1 TX data holding register and be cleared by writing to the UART1 data register. If the FIFO is enabled this interrupt will be active when the UART1 TX FIFO is half or more empty, and is cleared by filling the FIFO to at least half full. 13 URXINT1: Internal UART1 receive FIFO half full interrupt. The function of this interrupt source depends on whether the UART1 FIFO is enabled. If the FIFO is disabled this interrupt will be active when there is valid RX data in the UART1 RX data holding register and be cleared by reading this data. If the FIFO is enabled this interrupt will be active when the UART1 RX FIFO is half or more full or if the FIFO is non empty and no more characters have been received for a three character time out period. It is cleared by reading all the data from the RX FIFO. 14 UMSINT: Internal UART1 modem status changed interrupt. This interrupt will be active if either of the two modem status lines (CTS or DSR) change state. It is cleared by writing to the UMSEOI location. 15 SSEOTI: Synchronous serial interface end of transfer interrupt. This interrupt will be active after a complete data transfer to and from the external ADC has been completed. It is cleared by reading the ADC data from the SYNCIO register. Table 32. INTSR1 (cont.) 66 DS453PP2 EP7209 5.3.2 INTMR1 Interrupt Mask Register 1 ADDRESS: 0x8000.0280 15 14 13 12 11 10 9 8 SSEOTI UMSINT URXINT UTXINT TINT RTCMI TC2OI TC1OI 7 6 5 4 3 2 1 0 EINT3 EINT2 EINT1 CSINT MCINT WEINT BLINT EXTFIQ This interrupt mask register is a 32-bit read/write register, which is used to selectively enable any of the first 16 interrupt sources within the EP7209. The four shaded interrupts all generate a fast interrupt request to the ARM720T processor (FIQ), this will cause a jump to processor virtual address 0000.0001C. All other interrupts will generate a standard interrupt request (IRQ), this will cause a jump to processor virtual address 0000.00018. Setting the appropriate bit in this register enables the corresponding interrupt. All bits are cleared by a system reset. Please refer to INTSR1 Interrupt Status Register 1 for individual bit details. 5.3.3 INTSR2 Interrupt Status Register 2 ADDRESS: 0x8000.1240 15:14 13 12 11:3 2 1 0 Reserved URXINT2 UTXINT2 Reserved SS2TX SS2RX KBDINT This register is an extension of INTSR1, containing status bits for backward compatibility with CLPS7111. The interrupt status register also reflects the current state of the new interrupt sources within the EP7209. Each bit is set if the appropriate interrupt is active. The interrupt assignment is given in Table 33. Bit Description 0 KBDINT: Keyboard interrupt. This interrupt is generated whenever a key is pressed, from the logical OR of the first 6 or all 8 of the Port A inputs (depending on the state of the KBD6 bit in the SYSCON2 register. The interrupt request is latched, and can be de-asserted by writing to the KBDEOI location. NOTE: KBDINT is not deglitched. 1 SS2RX: Synchronous serial interface 2 receive FIFO half or greater full interrupt. This is generated when RX FIFO contains 8 or more half-words. This interrupt is cleared only when the RX FIFO is emptied or one SSI2 clock after RX is disabled. 2 SS2TX: Synchronous serial interface 2 transmit FIFO less than half empty interrupt. This is generated when TX FIFO contains fewer than 8 byte pairs. This interrupt gets cleared by loading the FIFO with more data or disabling the TX. One synchronization clock required when disabling the TX side before it takes effect. 12 UTXINT2: UART2 transmit FIFO half empty interrupt. The function of this interrupt source depends on whether the UART2 FIFO is enabled. If the FIFO is disabled (FIFOEN bit is clear in the UART2 bit rate and line control register), this interrupt will be active when there is no data in the UART2 TX data holding register and be cleared by writing to the UART2 data register. If the FIFO is enabled this interrupt will be active when the UART2 TX FIFO is half or more empty, and is cleared by filling the FIFO to at least half full. DS453PP2 67 EP7209 Bit Description 13 URXINT2: UART2 receive FIFO half full interrupt. The function of this interrupt source depends on whether the UART2 FIFO is enabled. If the FIFO is disabled this interrupt will be active when there is valid RX data in the UART2 RX data holding register and be cleared by reading this data. If the FIFO is enabled this interrupt will be active when the UART2 RX FIFO is half or more full or if the FIFO is non empty and no more characters have been received for a three character time out period. It is cleared by reading all the data from the RX FIFO. Table 33. INSTR2 (cont.) 5.3.4 INTMR2 Interrupt Mask Register 2 ADDRESS: 0x8000.1280 15:14 13 12 11:3 2 1 0 Reserved URXINT2 UTXINT2 Reserved SS2TX SS2RX KBDINT This register is an extension of INTMR1, containing interrupt mask bits for the backward compatibility with the CL-PS7111. Please refer to INTSR2 for individual bit details. 5.3.5 INTSR3 Interrupt Status Register 3 ADDRESS: 0x8000.2240 7:1 0 Reserved DAIINT This register is an extension of INTSR1 and INTSR2 containing status bits for the new features of the EP7209. Each bit is set if the appropriate interrupt is active. The interrupt assignment is given in Table 34. Bit 0 Description MCPINT: DAI interface interrupt. The cause must be determined by reading the DAI status register. It is mapped to the FIQ interrupt on the ARM720T processor Table 34. INTSR3 5.3.6 INTMR3 Interrupt Mask Register 3 ADDRESS: 0x8000.2280 7:1 0 Reserved DAIINT This register is an extension of INTMR1 and INTMR2, containing interrupt mask bits for the new features of the EP7209. Please refer to INTSR3 for individual bit details. 68 DS453PP2 EP7209 5.4 Memory Configuration Registers 5.4.1 MEMCFG1 Memory Configuration Register 1 ADDRESS: 0x8000.0180 31:24 23:16 15:8 7:0 nCS[3] configuration nCS[2] configuration nCS[1] configuration nCS[0] configuration Expansion and ROM space is selected by one of eight chip selects. One of the chip selects (nCS[6]) is used internally for the on-chip SRAM, and the configuration is hardwired for 32-bit wide, minimum wait state operation. nCS[7] is used for the on-chip Boot ROM and the configuration field is hardwired for 8-bit wide, minimum wait state operation. Data written to the configuration fields for either nCS[6] or nCS7 will be ignored. Two of the chip selects (nCS[4:5]) can be used to access two CL-PS6700 PC CARD controller devices, and when either of these interfaces is enabled, the configuration field for the appropriate chip select in the MEMCFG2 register is ignored. When the PC CARD1 or 2 control bit in the SYSCON2 register is disabled, then nCS[4] and nCS[5] are active as normal and can be programmed using the relevant fields of MEMCFG2, as for the other four chip selects. All of the six external chip selects are active for 256 Mbytes and the timing and bus transfer width can be programmed individually. This is accomplished by programming the six byte-wide fields contained in two 32-bit registers, MEMCFG1 and MEMCFG2. All bits in these registers are cleared by a system reset (except for the nCS[6] and nCS[7] configurations). The Memory Configuration Register 1 is a 32-bit read/write register which sets the configuration of the four expansion and ROM selects nCS[0:3]. Each select is configured with a 1-byte field starting with expansion select 0. 5.4.2 MEMCFG2 Memory Configuration Register 2 ADDRESS: 0x8000.01C0 31:24 (Boot ROM) 7 CLKENB 23:16 (Local SRAM) 6 SQAEN 15:8 nCS[5] configuration 5:2 Wait States Field 7:0 nCS[4] configuration 1:0 Bus width The Memory Configuration Register 2 is a 32-bit read/write register which sets the configuration of the two expansion and ROM selects nCS[4:5]. Each select is configured with a 1-byte field starting with expansion select 4. Each of the six non-reserved byte fields for chip select configuration in the memory configuration registers are identical and define the number of wait states, the bus width, enable EXPCLK output during accesses and enable sequential mode access. This byte field is defined below. This arrangement applies to nCS[0:3], and nCS[4:5] when the PC CARD enable bits in the SYSCON2 register are not set. The state of these bits is ignored for the Boot ROM and local SRAM fields in the MEMCFG2 register. Table 35 defines the bus width field. Note that the effect of this field is dependent on the two BOOTBIT bits that can be read in the SYSFLG1 register. All bits in the memory configuration register are cleared by a system reset and the state of the BOOTBIT bits are determined by Port E bits 0 and 1 on the EP7209 during power-on reset. The state of PE[1] and PE[0] determine whether the EP7209 is going to boot from either 32-bit wide, 16-bit wide or 8-bit wide ROMs. Table 36 shows the values for the wait states for random and sequential wait states at 13 and 18 MHz bus rates. At 36 MHz bus rate, the encoding becomes more complex. Table 37 preserves compatibility with the previous devices, while allowing the previously unused bit combinations to specify more variations of random and sequential wait states. DS453PP2 69 EP7209 Bus Width Field BOOTBIT1 BOOTBIT0 Expansion Transfer Mode Port E bits 1,0 during NPOR reset 00 01 10 11 00 01 10 11 00 01 10 11 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 32-bit wide bus access 16-bit wide bus access 8-bit wide bus access Reserved 8-bit wide bus access Reserved 32-bit wide bus access 16-bit wide bus access 16-bit wide bus access 32-bit wide bus access Reserved 8-bit wide bus access Low, Low Low, Low Low, Low Low, Low Low, High Low, High Low, High Low, High High, Low High, Low High, Low High, Low Table 35. Values of the Bus Width Field Value No. of Wait States Random No. of Wait States Sequential 00 01 10 11 4 3 2 1 3 2 1 0 Table 36. Values of the Wait State Field at 13 MHz and 18 MHz Bit 3 Bit 2 Bit 1 Bit 0 Wait States Random Wait States Sequential 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 Table 37. Values of the Wait State Field at 36 MHz 70 DS453PP2 EP7209 Bit Description 6 SQAEN: Sequential access enable. Setting this bit will enable sequential accesses that are on a quad word boundary to take advantage of faster access times from devices that support page mode. The sequential access will be faulted after four words (to allow video refresh cycles to occur), even if the access is part of a longer sequential access. In addition, when this bit is not set, non-sequential accesses will have a single idle cycle inserted at least every four cycles so that the chip select is de-asserted periodically between accesses for easier debug. 7 CLKENB: Expansion clock enable. Setting this bit enables the EXPCLK to be active during accesses to the selected expansion device. This will provide a timing reference for devices that need to extend bus cycles using the EXPRDY input. Back to back (but not necessarily page mode) accesses will result in a continuous clock. This bit will only affect EXPCLK when the PLL is being used (i.e., in 73.728–18.432 MHz mode). When operating in 13 MHz mode, the EXPCLK pin is an input so it is not affected by this register bit. To save power internally, it should always be set to zero when operating in 13 MHz mode. Table 38. MEMCFG See the AC Electrical Specification section for more detail on bus timing. The memory area decoded by CS[6] is reserved for the on-chip SRAM, hence this does not require a configuration field in MEMCFG2. It is automatically set up for 32-bit wide, no wait state accesses. For the Boot ROM, it is automatically set up for 8-bit, no wait state accesses. Chip selects nCS[4] and nCS[5] are used to select two CL-PS6700 PC CARD controller devices. These have a multiplexed 16-bit wide address/data interface, and the configuration bytes in the MEMCFG2 register have no meaning when these interfaces are enabled. 5.5 5.5.1 Timer/Counter Registers TC1D Timer Counter 1 Data Register ADDRESS: 0x8000.0300 The timer counter 1 data register is a 16-bit read/write register which sets and reads data to TC1. Any value written will be decremented on the next rising edge of the clock. 5.5.2 TC2D Timer Counter 2 Data Register ADDRESS: 0x8000.0340 The timer counter 2 data register is a 16-bit read/write register which sets and reads data to TC2. Any value written will be decremented on the next rising edge of the clock. 5.5.3 RTCDR Real Time Clock Data Register ADDRESS: 0x8000.0380 The Real Time Clock data register is a 32-bit read/write register, which sets and reads the binary time in the RTC. Any value written will be incremented on the next rising edge of the 1 Hz clock. This register is reset only by nPOR. 5.5.4 RTCMR Real Time Clock Match Register ADDRESS: 0x8000.03C0 The Real Time Clock match register is a 32-bit read/write register, which sets and reads the binary match time to RTC. Any value written will be compared to the current binary time in the RTC, if they match it will assert the RTCMI interrupt source. This register is reset only by nPOR. DS453PP2 71 EP7209 5.6 LEDFLSH Register ADDRESS: 0x8000.22C0 6 5:2 1:0 Enable Duty ratio Flash rate The output is enabled whenever LEDFLSH[6] = 1. When enabled, PDDDR[0] needs to be configured as an output pin and the bit cleared to ‘0’ (See PDDDR Port D Data Direction Register). When the LED Flasher is disabled, the pin defaults to being used as Port D bit 0. Thus, this will ensure that the LED will be off when disabled. The flash rate is determined by the LEDFLSH[1:0] bits, in the following way: LEDFLSH[1:0] Flash Period (sec) 00 1 01 2 10 3 11 4 Table 39. LED Flash Rates LEDFLSH[5:2] Duty Ratio (time on : time off) LEDFLSH[5:2] Duty Ratio (time on : time off) 0000 01:15 1000 09:07 0001 02:14 1001 10:06 0010 03:13 1010 11:05 0011 04:12 1011 12:04 0100 05:11 1100 13:03 0101 06:10 1101 14:02 0110 07:09 1110 15:01 0111 08:08 1111 16:00 (continually on) Table 40. LED Duty Ratio 72 DS453PP2 EP7209 5.7 PMPCON Pump Control Register ADDRESS: 0x8000.0400 11:8 7:4 3:0 Drive 1 pump ratio Drive 0 from AC source ratio Drive 0 from battery ratio The Pulse Width Modulator (PWM) pump control register is a 16-bit read/write register which sets and controls the variable mark space ratio drives for the two PWMs. All bits in this register are cleared by a system reset. (The top four bits are unused. They should be written as zeroes, and will read as undefined). Bit Description 0:3 Drive 0 from battery: This 4-bit field controls the ‘on’ time for the Drive 0 PWM pump while the system is powered from batteries. Setting these bits to 0 disables this pump, setting these bits to 1 allows the pump to be driven in a 1:16 duty ratio, 2 in a 2:16 duty ratio etc. up to a 15:16 duty ratio. An 8:16 duty ratio results in a square wave of 96 kHz when operating with an 18.432 MHz master clock, or 101.6 kHz when operating from the 13 MHz source. 4:7 Drive 0 from AC: This 4-bit field controls the ‘on’ time for the Drive 0 DC to DC pump while the system is powered from a non-battery type power source. Setting these bits to 0 disables this pump, setting these bits to 1 allows the pump to be driven in a 1:16 duty ratio, 2 in a 2:16 duty ratio, etc. up to a 15:16 duty ratio. An 8:16 duty ratio results in a square wave of 96 kHz when operating with an 18.432 MHz master clock, or 101.6 kHz when operating from the 13 MHz source. NOTE: The EP7209 monitors the power supply input pins (i.e., BATOK and NEXTPWR) to determine which of the above fields to use. 8:11 Drive 1 pump ratio: This 4-bit field controls the ‘on’ time for the drive1 PWM pump. Setting these bits to 0 disables this pump, setting these bits to 1 allows the pump to be driven in a 1:16 duty ratio, 2 in a 2:16 duty ratio, etc. up to a 15:16 duty ratio. An 8:16 duty ratio results in a square wave of 96 kHz when operating with an 18.432 MHz master clock, or 101.6 kHz when operating from the 13 MHz source. Table 41. PMPCON The state of the output drive pins is latched during power on reset, this latched value is used to determine the polarity of the drive output. The sense of the PWM control lines is summarized in Table 42. Initial State of Drive 0 or Drive 1 During Power on Reset Sense of Drive 0 or Drive 1 Polarity of Bias Voltage Low Active high +ve High Active low -ve Table 42. Sense of PWM control lines External input pins that would normally be connected to the output from comparators monitoring the PWM output are also used to enable these clocks. These are the FB[0:1] pins.When FB[0] is high, the PWM is disabled. The same applies to FB[1]. They are read upon power-up. NOTE: To maximize power savings, the drive ratio fields should be used to disable the PWMs, instead of the FB pins. The clocks that source the PWMs are disabled when the drive ratio fields are zeroed. DS453PP2 73 EP7209 5.8 CODR — The CODEC Interface Data Register ADDRESS: 0x8000.0440 The CODR register is an 8-bit read/write register, to be used with the codec interface. This is selected by the appropriate setting of bit 0 (SERSEL) of the SYSCON2 register. Data written to or read from this register is pushed or popped onto the appropriate 16-byte FIFO buffer. Data from this buffer is then serialized and sent to or received from the codec sound device. When the codec is enabled, the codec interrupt CSINT is generated repetitively at 1/8th of the byte transfer rate and the state of the FIFOs can be read in the system flags register. The net data transfer rate to/from the codec device is 8 kBytes/s, giving an interrupt rate of 1 kHz. 5.9 UART Registers 5.9.1 UARTDR1–2 UART1–2 Data Registers ADDRESS: 0x8000.0480 and 0x8000.1480 10 9 8 7:0 OVERR PARERR FRMERR RX data The UARTDR registers are 11-bit read and 8-bit write registers for all data transfers to or from the internal UARTs 1 and 2. Data written to these registers is pushed onto the 16-byte data TX holding FIFO if the FIFO is enabled. If not it is stored in a one byte holding register. This write will initiate transmission from the UART. The UART data read registers are made up of the 8-bit data byte received from the UART together with three bits of error status. If the FIFO is enabled, data read from this register is popped from the 16 byte data RX FIFO. If the FIFO is not enabled, it is read from a one byte buffer register containing the last byte received by the UART. If it is enabled, data received and error status is automatically pushed onto the RX FIFO. The RX FIFO is 10-bits wide by 16 deep. NOTE: Bit These registers should be accessed as words. Description 8 FRMERR: UART framing error. This bit is set if the UART detected a framing error while receiving the associated data byte. Framing errors are caused by non-matching word lengths or bit rates. 9 PARERR: UART parity error. This bit is set if the UART detected a parity error while receiving the data byte. 10 OVERR: UART over-run error. This bit is set if more data is received by the UART and the FIFO is full. The overrun error bit is not associated with any single character, and so is not stored in the FIFO, if this bit is set the entire contents of the FIFO is invalid and should be cleared. This error bit is cleared by reading the UARTDR register. Table 43. UARTDR1-2 UART1-2 74 DS453PP2 EP7209 5.9.2 UBRLCR1–2 UART1–2 Bit Rate and Line Control Registers ADDRESS: 0x8000.04C0 and 0x8000.14C0 31:19 18:17 16 15 14 13 12 11:0 WRDLEN FIFOEN XSTOP EVENPRT PRTEN BREAK Bit rate divisor The bit rate divisor and line control register is a 19-bit read / write register. Writing to these registers sets the bit rate and mode of operation for the internal UARTs. Bit 0:11 Description Bit rate divisor: This 12-bit field sets the bit rate. If the system is operating from the PLL clock, then the bit rate divider is fed by a clock frequency of 3.6864 MHz, which is then further divided internally by 16 to give the bit rate. The formula to give the divisor value for any bit rate when operating from the PLL clock is: Divisor = (230400/bit rate divisor) – 1. A value of zero in this field is illegal when running from the PLL clock. The tables below show some example bit rates with the corresponding divisor value. In 13 MHz mode, the clock frequency fed to the UART is 1.8571 MHz. In this mode, zero is a legal divisor value, and will generate the maximum possible bit rate. The tables below show the bit rates available for both 18.432 MHz and 13 MHz operation. Divisor Value Bit Rate Running From the Pll Clock 0 — 1 Divisor Value Bit Rate at 13 Mhz Error on 13 MHz Value 115200 0 116071 0.75% 2 76800 1 58036 0.75% 3 57600 2 38690 0.75% 5 38400 5 19345 0.75% 11 19200 7 14509 0.75% 15 14400 11 9673 0.75% 23 9600 47 2418 0.42% 95 2400 96 1196 0.28% 191 1200 1054 110.02 0.18% 2094 110 12 BREAK: Setting this bit will drive the TX output active (high) to generate a break. 13 PRTEN: Parity enable bit. Setting this bit enables parity detection and generation 14 EVENPRT: Even parity bit. Setting this bit sets parity generation and checking to even parity, clearing it sets odd parity. This bit has no effect if the PRTEN bit is clear. 15 XSTOP: Extra stop bit. Setting this bit will cause the UART to transmit two stop bits after each data byte, clearing it will transmit one stop bit after each data byte. Table 44. UBRLCR1-2 UART1-2 DS453PP2 75 EP7209 Bit Description 16 FIFOEN: Set to enable FIFO buffering of RX and TX data. Clear to disable the FIFO (i.e., set its depth to one byte). 17:18 WRDLEN: This two bit field selects the word length according to the table below. WRDLEN Word Length 00 5 bits 01 6 bits 10 7 bits 11 8 bits Table 44. UBRLCR1-2 UART1-2 (cont.) 76 DS453PP2 EP7209 5.10 LCD Registers 5.10.1 LCDCON — The LCD Control Register ADDRESS: 0x8000.02C0 31 30 29:25 24:19 18:13 12:0 GSMD GSEN AC prescale Pixel prescale Line length Video buffer size The LCD control register is a 32-bit read/write register that controls the size of the LCD screen and the operating mode of the LCD controller. Refer to the system description of the LCD controller for more information on video buffer mapping. The LCDCON register should only be reprogrammed when the LCD controller is disabled. Bit Description 0:12 Video buffer size: The video buffer size field is a 13-bit field that sets the total number of bits x 128 (quad words) in the video display buffer. This is calculated from the formula: Video buffer size = (Total bits in video buffer / 128) – 1 i.e., for a 640 x 240 LCD and 4-bits per pixel, the size of the video buffer is equal to 614400 bits. Video buffer = 640 x 240 x 4=614400 bits Video buffer size field = (614400 / 128) – 1 = 4799 or 0x12BF hex. The minimum value allowed is 3 for this bit field. 13:18 Line length: The line length field is a 6-bit field that sets the number of pixels in one complete line. This field is calculated from the formula: line length = (Number of pixels in line / 16) – 1 i.e., for 640 x 240 LCD Line length = (640 / 16) – 1 = 39 or 0x27 hex. The minimum value that can be programmed into this register is a 1 (i.e., 0 is not a legal value). 19:24 Pixel prescale: The pixel prescale field is a 6-bit field that sets the pixel rate prescale. The pixel rate is always derived from a 36.864 MHz clock when in PLL mode, and is calculated from the formula: Pixel rate (MHz) = 36.864 / (Pixel prescale + 1) When the EP7209 is operating at 13 MHz, pixel rate is given by the formula: Pixel rate (MHz) = 13 / (Pixel prescale + 1) The pixel prescale value can be expressed in terms of the LCD size by the formula: When the EP7209 is operating @ 18.432 MHz: Pixel prescale = (36864000 / (Refresh Rate x Total pixels in display)) – 1 When the EP7209 is operating @ 13 MHz: Pixel prescale = (13000000 / (Refresh Rate x Total pixels in display)) – 1 Refresh Rate is the screen refresh frequency (70 Hz to avoid flicker) The value should be rounded down to the nearest whole number and zero is illegal and will result in no pixel clock. EXAMPLE: For a system being operated in the 18.432–73.728 MHz mode, with a 640 x 240 screen size, and 70 Hz screen refresh rate desired, the LCD Pixel prescale equals 36.864E6/(70 x 640x240) – 1 = 2.428 Rounding 2.428 down to the nearest whole number equals 2. This gives an actual pixel rate of 36.864E6 / (2+1) = 12.288 MHz Which gives an actual refresh frequency of 12.288E6/(640x240) = 80 Hz. NOTE: As the CL[2] low pulse time is doubled after every CL[1] high pulse this refresh frequency is only an approximation, the accurate formula is 12.288E6/((640x240)+120) = 79.937 Hz. Table 45. LCDCON DS453PP2 77 EP7209 Bit Description 25:29 AC prescale: The AC prescale field is a 5-bit number that sets the LCD AC bias frequency. This frequency is the required AC bias frequency for a given manufacturer’s LCD plate. This frequency is derived from the frequency of the line clock (CL[1]). The LCD M signal will toggle after n+1 counts of the line clock (CL[1]) where n is the number programmed into the AC prescale field. This number must be chosen to match the manufacturer’s recommendation. This is normally 13, but must not be exactly divisible by the number of lines in the display. 30 GSEN: Gray scale enable bit. Setting this bit enables gray scale output to the LCD. When this bit is cleared each bit in the video map directly corresponds to a pixel in the display. 31 GSMD: Gray scale mode bit. Clearing this bit sets the controller to 2-bits per pixel (4 gray scales), setting it sets it to 4 bits per pixel (16 gray scales). This bit has no effect if GSEN is cleared. Table 45. LCDCON (cont.) 5.10.2 PALLSW Least Significant Word — LCD Palette Register ADDRESS: 0x8000.0580 31:28 Gray scale value for pixel value 7 27:24 23:20 19:16 15:12 11:8 7:4 3:0 Gray scale Gray scale Gray scale Gray scale Gray scale Gray scale Gray scale value for pixel value for pixel value for pixel value for pixel value for pixel value for pixel value for pixel value 6 value 5 value 4 value 3 value 2 value 1 value 0 The least and most significant word LCD palette registers make up a 64-bit read/write register which maps the logical pixel value to a physical gray scale level. The 64-bit register is made up of 16 x 4-bit nibbles, each nibble defines the gray scale level associated with the appropriate pixel value. If the LCD controller is operating in two bits per pixel, only the lower 4 nibbles are valid (D[15:0] in the least significant word). Similarly, one bit per pixel means only the lower 2 nibbles are valid (D[7:0]) in the least significant word. 5.10.3 PALMSW Most Significant Word — LCD Palette Register ADDRESS: 0x8000.0540 31:28 Gray scale value for pixel value 15 27:24 23:20 19:16 15:12 11:8 7:4 3:0 Gray scale Gray scale Gray scale Gray scale Gray scale Gray scale Gray scale value for pixel value for pixel value for pixel value for pixel value for pixel value for pixel value for pixel value 14 value 13 value 12 value 11 value 10 value 9 value 8 The pixel to gray scale level assignments and the actual physical color and pixel duty ratio for the gray scale values are shown in Table 46. Note that colors 8–15 are the inverse of colors 7–0 respectively. This means that colors 7 and 8 are identical. Therefore, in reality only 15 gray scales available, not 16. The steps in the gray scale are non-linear, but have been chosen to give a close approximation to perceived linear gray scales. The is due to the eye being more sensitive to changes in gray level close to 50% gray (See PALLSW description). 78 DS453PP2 EP7209 Gray Scale Value Duty Cycle % Pixels Lit % Step Change 0 0 0% 11.1 % 1 1/9 11.1 % 8.9 % 2 1/5 20.0 % 6.7 % 3 4/15 26.7 % 6.6 % 4 3/9 33.3 % 6.7 % 5 2/5 40.0 % 5.4 % 6 4/9 44.4 % 5.6 % 7 1/2 50.0 % 0.0 % 8 1/2 50.0 % 5.6 % 9 5/9 55.6 % 5.4 % 10 3/5 60.0 % 6.7 % 11 6/9 66.7 % 6.6 % 12 11/15 73.3 % 6.7 % 13 4/5 80.0 % 8.9 % 14 8/9 88.9 % 11.1 % 15 1 100 % Table 46. Gray Scale Value to Color Mapping 5.10.4 FBADDR LCD Frame Buffer Start Address ADDRESS: 0x8000.1000 This register contains the start address for the LCD Frame Buffer. It is assumed that the frame buffer starts at location 0x0000000 within each chip select memory region. Therefore, the value stored within the FBADDR register is only the value of the chip select where the frame buffer is located. On reset, this will be set to 0xC. The register is 4 bits wide (bits [3:0]). This register must only be reprogrammed when the LCD is disabled (i.e., setting the LCDEN bit within SYSCON2 low). 5.11 SSI Register 5.11.1 SYNCIO Synchronous Serial ADC Interface Data Register ADDRESS: a0x8000.0500 In the default mode, the bits in SYNCIO have the following meaning: 31:15 14 13 12:8 7:0 Reserved TXFRMEN SMCKEN Frame length ADC Configuration Byte 15 14 13 12:7 6:0 Reserved TXFRMEN SMCKEN Frame length ADC Configuration Length Whereas in extended mode, the following applies: ADC Configuration Extension NOTE: The frame length in extended mode is 6 bits wide to allow up to 16 write bits, 1 null bit and 16 read bits (= 33 cycles). DS453PP2 79 EP7209 SYNCIO is a 32-bit read/write register. The data written to the SYNCIO register configures the master only SSI. In default mode, the least significant byte is serialized and transmitted out of the synchronous serial interface1 (i.e., SSI1) to configure an external ADC, MSB first. In extended mode, a variable number of bits are sent from SYNCIO[16:31] as determined by the ADC Configuration Length. The transfer clock will automatically be started at the programmed frequency and a synchronization pulse will be issued. The ADCIN pin is sampled on every positive going clock edge (or the falling clock edge, if ADCCKNSEN in SYSCON3 is set) and the result is shifted in to the SYNCIO read register. During data transfer, the SSIBUSY bit is set high; at the end of a transfer the SSEOTI interrupt will be asserted. In order to clear the interrupt the SYNCIO register must be read. The data read from the SYNCIO register is the last sixteen bits shifted out of the ADC. The length of the data frame can be programmed by writing to the SYNCIO register. This allows many different ADCs to be accommodated. The device is SPI/Microwire compatible (transfers are in multiples of 8 bits). However, to be compatible with some non-SPI/Microwire devices, the data written to the ADC device can be anything between 8 to 16 bits. This is user-definable as defined in the ADC Configuration Extension section of the SYNCIO register. Bit Description 0:7 or 0:6 ADC Configuration Byte: When the ADCCON control bit in the SYSCON3 register = 0, this is the 8-bit configuration data to be sent to the ADC. When the ADCCON control bit in the SYSCON3 register = 1, this field determines the length of the ADC configuration data held in the ADC Configuration Extension field for sending to the ADC. 8:12 or 7:12 Frame length: The Frame Length Field is the total number of shift clocks required to complete a data transfer. In default mode, MAX148/9 (and for many ADCs), this is 25 = (8 for configuration byte + 1 null bit + 16 bits result). In extended mode, AD7811/12, this is 23 = (10 for configuration byte + 3 null + 10 bits result). 13 SMCKEN: Setting this bit will enable a free running sample clock at twice the programmed ADC clock frequency to be output on the SMPLCK pin. 14 TXFRMEN: Setting this bit will cause an ADC data transfer to be initiated. The value in the ADC configuration field will be shifted out to the ADC and depending on the frame length programmed, a number of bits will be captured from the ADC. If the SYNCIO register is written to with the TXFRMEN bit low, no ADC transfer will take place, but the Frame length and SMCKEN bits will be affected. 16:31 ADC Configuration Extension: When the ADCCON control bit in the SYSCON3 register = 0 this field is ignored for compatibility with the CL-PS7111. When the ADCCON control bit in the SYSCON3 register = 1, this field is the configuration data to be sent to the ADC. The ADC Configuration Extension field length is determined by the value held in the ADC Configuration Length field (SYNCIO[6:0]). Table 47. SYNCIO 5.12 STFCLR Clear all ‘Start Up Reason’ flags location ADDRESS: 0x8000.05C0 A write to this location will clear all the ‘Start Up Reason’ flags in the system flags status register SYSFLG. The ‘Start Up Reason’ flags should first read to determine the reason why the chip was started (i.e., a new battery was installed). Any value may be written to this location. 80 DS453PP2 EP7209 5.13 ‘End Of Interrupt’ Locations These locations are written to after the appropriate interrupt has been serviced. The write is performed to clear the interrupt status bit, so that other interrupts can be serviced. Any value may be written to these locations. 5.13.1 BLEOI Battery Low End of Interrupt ADDRESS: 0x8000.0600 A write to this location will clear the interrupt generated by a low battery (falling edge of BATOK with nEXTPWR high). 5.13.2 MCEOI Media Changed End of Interrupt ADDRESS: 0x8000.0640 A write to this location will clear the interrupt generated by a falling edge of the nMEDCHG input pin. 5.13.3 TEOI Tick End of Interrupt Location ADDRESS: 0x8000.0680 A write to this location will clear the current pending tick interrupt and tick watch dog interrupt. 5.13.4 TC1EOI TC1 End of Interrupt Location ADDRESS: 0x8000.06C0 A write to this location will clear the under flow interrupt generated by TC1. DS453PP2 81 EP7209 5.13.5 TC2EOI TC2 End of Interrupt Location ADDRESS: 0x8000.0700 A write to this location will clear the under flow interrupt generated by TC2. 5.13.6 RTCEOI RTC Match End of Interrupt ADDRESS: 0x8000.0740 A write to this location will clear the RTC match interrupt 5.13.7 UMSEOI UART1 Modem Status Changed End of Interrupt ADDRESS: 0x8000.0780 A write to this location will clear the modem status changed interrupt. 5.13.8 COEOI Codec End of Interrupt Location ADDRESS: 0x8000.07C0 A write to this location clears the sound interrupt (CSINT). 5.13.9 KBDEOI Keyboard End of Interrupt Location ADDRESS: 0x8000.1700 A write to this location clears the KBDINT keyboard interrupt. 5.13.10 SRXEOF End of Interrupt Location ADDRESS: 0x8000.1600 A write to this location clears the SSI2 RX FIFO overflow status bit. 5.14 5.14.1 State Control Registers STDBY Enter the Standby State Location ADDRESS: 0x8000.0840 A write to this location will put the system into the Standby State by halting the main oscillator. A write to this location while there is an active interrupt will have no effect. NOTES: 1) Before entering the Standby State, the LCD Controller should be disabled. The LCD controller should be enabled on exit from the Standby State. 2) If the EP7209 is attempting to get into the Standby State when there is a pending interrupt request, it will not enter into the low power mode. The instruction will get executed, but the processor will ignore the command. 5.14.2 HALT Enter the Idle State Location ADDRESS: 0x8000.0800 A write to this location will put the system into the Idle State by halting the clock to the processor until an interrupt is generated. A write to this location while there is an active interrupt will have no effect. 82 DS453PP2 EP7209 5.15 5.15.1 SS2 Registers SS2DR Synchronous Serial Interface 2 Data Register ADDRESS: 0x8000.1500 This is the 16-bit wide data register for the full-duplex master/slave SSI2 synchronous serial interface. Writing data to this register will initiate a transfer. Writes need to be word writes and the bottom 16 bits are transferred to the TX FIFO. Reads will be 32 bits as well; the low 16 bits contain RX data and the upper 16-bits should be ignored. Although the interface is byte-oriented, data is written in two bytes at a time to allow higher bandwidth transfer. It is up to the software to assemble the bytes for the data stream in an appropriate manner. All reads/writes to this register must be word reads/writes. 5.15.2 SS2POP Synchronous Serial Interface 2 Pop Residual Byte ADDRESS: 0x8000.16C0 This is a write-only location which will cause the contents of the RX shift register to be popped into the RX FIFO, thus enabling a residual byte to be read. The data value written to this register is ignored. This location should be used in conjunction with the RESVAL and RESFRM bits in the SYSFLG2 register. 5.16 DAI Register Definitions There are five registers within the DAI Interface, one control register, three data registers, and one status register. The control register is used to mask or unmask interrupt requests to service the DAI’s FIFOs, and to select whether an on-chip or off-chip clock is used to drive the bit rate, and to enable/disable operation. The first pair of data register addresses the top of the right channel transmit FIFO and the bottom of the right channel receive FIFO. A read accesses the receive FIFOs, and a write the transmit FIFOs. Note that these are four physically separate FIFOs to allow full-duplex transmission. The status register contains bits which signal FIFO overrun and underrun errors and transmit and receive FIFO service requests. Each of these status conditions signal an interrupt request to the interrupt controller. The status register also flags when the transmit FIFOs are not full when the receive FIFOs are not empty. DS453PP2 83 EP7209 5.16.1 DAI Control Register ADDRESS: 0x8000.2000 31:24 23 22 21 20 19 18 17 16 15:0 Reserved LBM RCRM RCTM LCRM LCTM Reserved ECS DAIEN Reserved The DAI control register (DAIR) contains eight different bit fields that control various functions within the DAI interface. Bit 0:15 Description Reserved Must be set to 0x0404 7 Reserved 15 Reserved 16 DAIEN: DAI Interface Enable 0 — DAI operation disabled, control of the SDIN, SDOUT, SCLKLRCK, and LRCK pins given to the SSI2/codec/DAI pin mulitiplexing logic to assign I/O pins 60-64 to another block. 1 — DAI operation enabled Note that by default, the SSI/CODEC have precedence over the DAI interface in regard to the use of the I/O pins. Nevertheless, when Bit 3 (MCPSEL) of register SYSCON3 is set to 1, then the above mentioned DAI ports are connected to I/O pins 60–64. 17 ECS: External Clock Select selects external MCLK when = 1. 18 Reserved Must be 0. 19 LCTM: Left Channel Transmit FIFO Interrupt Mask 0 — Left Channel transmit FIFO half-full or less condition does not generate an interrupt (LCTS bit ignored). 1 — Left Channel transmit FIFO half-full or less condition generates an interrupt (state of LCTS sent to interrupt controller). 20 LCRM: Left Channel Receive FIFO Interrupt Mask 0 — Left Channel receive FIFO half-full or more condition does not generate an interrupt (LCRS bit ignored). 1 — Left Channel receive FIFO half-full or more condition generates an interrupt (state of LCRS sent to interrupt controller). 21 RCTM: Right Channel Transmit FIFO Interrupt Mask 0 — Right channel transmit FIFO half-full or less condition does not generate an interrupt (RCTS bit ignored). 1 — Right channel transmit FIFO half-full or less condition generates an interrupt (state of RCTS sent to interrupt controller). 22 RCRM: Right Channel Receive FIFO Interrupt Mask 0 — Right Channel receive FIFO half-full or more condition does not generate an interrupt (RCRS bit ignored). 1 — Right Channel receive FIFO half-full or more condition generates an interrupt (state of RCRS sent to interrupt controller). Table 48. DAI Control Register 84 DS453PP2 EP7209 Bit 23 24:31 Description LBM: Loop Back Mode 0 — Normal serial port operation enabled 1 — Output of serial shifter is connected to input of serial shifter internally and control of SDIN, SDOUT, SCLK, and LRCK pins is given to the PPC unit. Reserved Table 48. DAI Control Register (cont.) 5.16.1.1 DAI Enable (DAIEN) The DAI enable (DAIEN) bit is used to enable and disable all DAI operation. When the DAI is disabled, all of its clocks are powered down to minimize power consumption. Note that DAIEN is the only control bit within the DAI interface that is reset to a known state. It is cleared to zero to ensure the DAI timing is disabled following a reset of the device. When the DAI timing is enabled, SCLK begins to transition and the start of the first frame is signaled by driving the LRCK pin low. The rising and falling-edge of LRCK coincides with the rising and fallingedge of SCLK. As long as the DAIEN bit is set, the DAI interface operates continuously, transmitting and receiving 128 bit data frames. When the DAIEN bit is cleared, the DAI interface is disabled immediately, causing the current frame which is being transmitted to be terminated. Clearing DAIEN resets the DAI’s interface FIFOs. However DAI data register 3, the control register and the status register are not reset. Therefore, the user must ensure these registers are properly reconfigured before re-enabling the DAI interface. 5.16.1.2 DAI Interrupt Generation The DAI interface can generate four maskable interrupts and four non-maskable interrupts, as described in the sections below. Only one interrupt line is wired into the interrupt controller for the whole DAI interface. This interrupt is the wired OR of all eight interrupts (after masking where appropriate). The software servicing the interrupts must read the status register in the DAI to determine which source(s) caused the interrupt. It is possible to prevent any DAI sources causing an interrupt by masking the DAI interrupt in the interrupt controller register. 5.16.1.3 Left Channel Transmit FIFO Interrupt Mask (LCTM) The left channel sample transmit FIFO interrupt mask (LCTM) bit is used to mask or enable the left channel sample transmit FIFO service request interrupt. When LATM = 0, the interrupt is masked and the state of the left channel transmit FIFO service request (LCTS) bit within the DAI status register is ignored by the interrupt controller. When LCTM = 1, the interrupt is enabled and whenever LCTS is set (one) an interrupt request is made to the interrupt controller. Note that programming LCTM = 0 does not affect the current state of LCTS or the left channel transmit FIFO logic’s ability to set and clear LCTS; it only blocks the generation of the interrupt request. 5.16.1.4 Left Channel Receive FIFO Interrupt Mask (LARM) The left channel sample receive FIFO interrupt mask (LCRM) bit is used to mask or enable the left channel receive FIFO service request interrupt. When LCRM = 0, the interrupt is masked and the state of the left channel sample receive FIFO service request (LCRS) bit within the DAI status register is ignored by the interrupt controller. When LCRM = 1, the interrupt is enabled and whenever LCRS is set (one) an interrupt request is made to the interrupt controller. Note that programming LCRM = 0 does not affect the current state of LCRS or the left channel receive FIFO logic’s ability to set and clear LCRS, it only blocks the generation of the interrupt request. DS453PP2 85 EP7209 5.16.1.5 Right Channel Transmit FIFO Interrupt Mask (RCTM) The right channel transmit FIFO interrupt mask (RCTM) bit is used to mask or enable the right channel transmit FIFO service request interrupt. When RCTM = 0, the interrupt is masked and the state of the right channel transmit FIFO service request (RCTS) bit within the DAI status register is ignored by the interrupt controller. When RCTM = 1, the interrupt is enabled and whenever RCTS is set (one) an interrupt request is made to the interrupt controller. Note that programming RCTM = 0 does not affect the current state of RCTS or the right channel transmit FIFO logic’s ability to set and clear RCTS; it only blocks the generation of the interrupt request. 5.16.1.6 Right Channel Receive FIFO Interrupt Mask (RCRM) The right channel receive FIFO interrupt mask (RCRM) bit is used to mask or enable the right channel receive FIFO service request interrupt. When RCRM = 0, the interrupt is masked and the state of the right channel receive FIFO service request (RCRS) bit within the DAI status register is ignored by the interrupt controller. When RCRM = 1, the interrupt is enabled and whenever RCRS is set (one) an interrupt request is made to the interrupt controller. Note that programming RCRM = 0 does not affect the current state of RCRS or the right channel receive FIFO logic’s ability to set and clear RCRS; it only blocks the generation of the interrupt request. 5.16.1.7 Loop Back Mode (LBM) The loop back mode (LBM) bit is used to enable and disable the ability of the DAI’s transmit and receive logic to communicate. When LBM = 0, the DAI operates normally. The transmit and receive data paths are independent and communicate via their respective pins. When LBM = 1, the output of the serial shifter (MSB) is directly connected to the input of the serial shifter (LSB) internally and control of the SDOUT, SDIN, SCLK, and LRCK pins are given to the peripheral pin control (PPC) unit. Table 48 shows the bit locations corresponding to the ten different control bit fields within the DAI control register. Note that the DAIEN bit is the only control bit which is reset to a known state to ensure the DAI is disabled following a reset of the device. The reset state of all other control bits is unknown and must be initialized before enabling the DAI. Writes to reserved bits are ignored and reads return zeros. 86 DS453PP2 EP7209 5.16.2 DAI Data Registers The DAI contains three data registers: DAIDR0 addresses the top entry of the right channel transmit FIFO and bottom entry of the right channel receive FIFO; DAIDR1 addresses the top and bottom entry of the left channel transmit and receive FIFOs, respectively; and DAIDR2 is used to perform enable and disable the DAI FIFOs. 5.16.2.1 DAI Data Register 0 ADDRESS: 0x8000.2040 31:16 15:0 Reserved Bottom of Right Channel Receive FIFO Read Access 31:16 15:0 Reserved Top of Right Channel Transmit FIFO Write Access When DAI Data Register 0 (DAIDR0) is read, the bottom entry of the right channel receive FIFO is accessed. As data is removed by the DAI’s receive logic from the incoming data frame, it is placed into the top entry of the right channel receive FIFO and is transferred down an entry at a time until it reaches the last empty location within the FIFO. Data is removed by reading DAIDR0, which accesses the bottom entry of the right channel FIFO. After DAIDR0 is read, the bottom entry is invalidated, and all remaining values within the FIFO automatically transfer down one location. When DAIDR0 is written, the top-most entry of the right channel transmit FIFO is accessed. After a write, data is automatically transferred down to the lowest location within the transmit FIFO which does not already contain valid data. Data is removed from the bottom of the FIFO one value at a time by the transmit logic, loaded into the correct position within the 64-bit transmit serial shifter, then serially shifted out onto the SDOUT pin. Table 49 shows DAIDR0. Note that the transmit and receive right channel FIFOs are cleared when the device is reset, or by writing a zero to DAIEN (DAI disabled). Also, note that writes to reserved bits are ignored and reads return zeros. Bit Description 0:15 RIGHT CHANNEL DATA: Transmit/Receive right channel FIFO Data Read — Bottom of Right Channel Receive FIFO data Write — Top of Right Channel Transmit FIFO data 16:31 Reserved Table 49. DAI Data Register 0 DS453PP2 87 EP7209 5.16.2.2 DAI Data Register 1 ADDRESS: 0x8000.2080 31:16 15:0 Reserved Bottom of Left Channel Receive FIFO Read Access 31:16 15:0 Reserved Top of Left Channel Transmit FIFO Write Access When DAI Data Register 1 (DAIDR1) is read, the bottom entry of the left channel receive FIFO is accessed. As data is removed by the DAI’s receive logic from the incoming data frame, it is placed into the top entry of the left channel receive FIFO and is transferred down an entry at a time until it reaches the last empty location within the FIFO. Data is removed by reading DAIDR1, which accesses the bottom entry of the left channel FIFO. After DAIDR1 is read, the bottom entry is invalidated, and all remaining values within the FIFO automatically transfer down one location. When DAIDR1 is written, the top-most entry of the left channel transmit FIFO is accessed. After a write, data is automatically transferred down to the lowest location within the transmit FIFO which does not already contain valid data. Data is removed from the bottom of the FIFO one value at a time by the transmit logic. It is then loaded into the correct position within the 64-bit transmit serial shifter then serially shifted out onto the SDOUT pin. Table 50 shows DAIDR1. Note that the transmit and receive left channel FIFOs are cleared when the device is reset, or by writing a zero to DAIEN (DAI disabled). Also, note that writes to reserved bits are ignored and reads return zeros. Bit Description 0:15 LEFT CHANNEL DATA: Transmit/Receive left channel FIFO Data Read — Bottom of Left Channel Receive FIFO data Write — Top of Left Channel Transmit FIFO data 16:31 Reserved Table 50. DAI Data Register 1 5.16.2.3 DAI Data Register 2 ADDRESS: 0x8000.20C0 DAIDR2 contains 21 bits and is used to enable and disable the FIFOs for the left and right channels of the DAI data stream. The left channel FIFO is enabled by writing 0x000D.C000 and disabled by writing 0x000D.0000. The right channel FIFO is enabled by writing 0x0011.C000 and disabled by writing 0x0011.0000. After writing a value to this register, wait until the FIFO operation complete bit (FIFO) is set in the DAI status register before writing another value to this register. 88 DS453PP2 EP7209 5.16.3 DAI Status Register ADDRESS: 0x8000.2100 The DAI Status Register (DAISR) contains bits which signal FIFO overrun and underrun errors and FIFO service requests. Each of these conditions signal an interrupt request to the interrupt controller. The status register also flags when transmit FIFOs are not full, when the receive FIFOs are not empty, when a FIFO operation is complete, and when the right channel or left channel portion of the codec is enabled (no interrupt generated). Bits which cause an interrupt signal the interrupt request as long as the bit is set. Once the bit is cleared, the interrupt is cleared. Read/write bits are called status bits, read-only bits are called flags. Status bits are referred to as “sticky” (once set by hardware, they must be cleared by software). Writing a one to a sticky status bit clears it, writing a zero has no effect. Read-only flags are set and cleared by hardware, and writes have no effect. Additionally some bits which cause interrupts have corresponding mask bits in the control register and are indicated in the section headings below. Note that the user has the ability to mask all DAI interrupts by clearing the DAI bit within the interrupt controller mask register INTMR3. 5.16.3.1 Right Channel Transmit FIFO Service Request Flag (RCTS) The right channel transmit FIFO service request flag (RCTS) is a read-only bit which is set when the right channel transmit FIFO is nearly empty and requires service to prevent an underrun. RCTS is set any time the right channel transmit FIFO has four or fewer entries of valid data (half full or less), and is cleared when it has five or more entries of valid data. When the RCTS bit is set, an interrupt request is made unless the right channel transmit FIFO interrupt request mask (RCTM) bit is cleared. After the CPU fills the FIFO such that four or more locations are filled within the right channel transmit FIFO, the RCTS flag (and the service request and/or interrupt) is automatically cleared. 5.16.3.2 Right Channel Receive FIFO Service Request Flag (RCRS) The right channel receive FIFO service request flag (RCRS) is a read-only bit which is set when the right channel receive FIFO is nearly filled and requires service to prevent an overrun. RCRS is set any time the right channel receive FIFO has six or more entries of valid data (half full or more), and cleared when it has five or fewer (less than half full) entries of data. When the RCRS bit is set, an interrupt request is made unless the right channel receive FIFO interrupt request mask (RCRM) bit is cleared. After six or more entries are removed from the receive FIFO, the LCRS flag (and the service request and/or interrupt) is automatically cleared. 5.16.3.3 Left Channel Transmit FIFO Service Request Flag (LCTS) The left channel transmit FIFO service request flag (LCTS) is a read-only bit which is set when the left channel transmit FIFO is nearly empty and requires service to prevent an underrun. LCTS is set any time the left channel transmit FIFO has four or fewer entries of valid data (half full or less), and is cleared when it has five or more entries of valid data. When the LCTS bit is set, an interrupt request is made unless the left channel transmit FIFO interrupt request mask (LCTM) bit is cleared. After the CPU fills the FIFO such that four or more locations are filled within the left channel transmit FIFO, the LCTS flag (and the service request and/or interrupt) is automatically cleared. DS453PP2 89 EP7209 5.16.3.4 Left Channel Receive FIFO Service Request Flag (LCRS) The left channel receive FIFO service request flag (LCRS) is a read-only bit which is set when the left channel receive FIFO is nearly filled and requires service to prevent an overrun. LCRS is set any time the left channel receive FIFO has six or more entries of valid data (half full or more), and cleared when it has five or fewer (less than half full) entries of data. When the LCRS bit is set, an interrupt request is made unless the left channel receive FIFO interrupt request mask (LCRM) bit is cleared. After six or more entries are removed from the receive FIFO, the LCRS flag (and the service request and/or interrupt) is automatically cleared. 5.16.3.5 Right Channel Transmit FIFO Underrun Status (RCTU) The right channel transmit FIFO underrun status bit (RCTU) is set when the right channel transmit logic attempts to fetch data from the FIFO after it has been completely emptied. When an underrun occurs, the right channel transmit logic continuously transmits the last valid right channel value which was transmitted before the underrun occurred. Once data is placed in the FIFO and it is transferred down to the bottom, the right channel transmit logic uses the new value within the FIFO for transmission. When the RCTU bit is set, an interrupt request is made. 5.16.3.6 Right Channel Receive FIFO Overrun Status (RCRO) The right channel receive FIFO overrun status bit (RCRO) is set when the right channel receive logic attempts to place data into the right channel receive FIFO after it has been completely filled. Each time a new piece of data is received, the set signal to the RCRO status bit is asserted, and the newly received data is discarded. This process is repeated for each new sample received until at least one empty FIFO entry exists. When the RCRO bit is set, an interrupt request is made. 5.16.3.7 Left Channel Transmit FIFO Underrun Status (LCTU) The left channel transmit FIFO underrun status bit (LCTU) is set when the left channel transmit logic attempts to fetch data from the FIFO after it has been completely emptied. When an underrun occurs, the left channel transmit logic continuously transmits the last valid left channel value which was transmitted before the underrun occurred. Once data is placed in the FIFO and it is transferred down to the bottom, the left channel transmit logic uses the new value within the FIFO for transmission. When the LCTU bit is set, an interrupt request is made. 5.16.3.8 Left Channel Receive FIFO Overrun Status (LCRO) The left channel receive FIFO overrun status bit (LCRO) is set when the left channel receive logic places data into the left channel receive FIFO after it has been completely filled. Each time a new piece of data is received, the set signal to the LCRO status bit is asserted, and the newly received sample is discarded. This process is repeated for each new piece of data received until at least one empty FIFO entry exists. When the LCRO bit is set, an interrupt request is made. 5.16.3.9 Right Channel Transmit FIFO Not Full Flag (RCNF) The right channel transmit FIFO not full flag (RCNF) is a read-only bit which is set whenever the right channel transmit FIFO contains one or more entries which do not contain valid data and is cleared when the FIFO is completely full. This bit can be polled when using programmed I/O to fill the right channel transmit FIFO. This bit does not request an interrupt. 5.16.3.10 Right Channel Receive FIFO Not Empty Flag (RCNE) The right channel receive FIFO not empty flag (RCNELCNF) is a read-only bit which is set when ever the right channel receive FIFO contains one or more entries of valid data and is cleared when it no longer contains any valid data. This bit can be polled when using programmed I/O to remove remaining data from the receive FIFO. This bit does not request an interrupt. 90 DS453PP2 EP7209 5.16.3.11 Left Channel Transmit FIFO Not Full Flag (LCNF) The left channel transmit FIFO not full flag (LCNF) is a read-only bit which is set when ever the left channel transmit FIFO contains one or more entries which do not contain valid data. It is cleared when the FIFO is completely full. This bit can be polled when using programmed I/O to fill the left channel transmit FIFO. This bit does not request an interrupt. 5.16.3.12 Left Channel Receive FIFO Not Empty Flag (LCNE) The left channel receive FIFO not empty flag (LCNE) is a read-only bit which is set when ever the left channel receive FIFO contains one or more entries of valid data and is cleared when it no longer contains any valid data. This bit can be polled when using programmed I/O to remove remaining data from the receive FIFO. This bit does not request an interrupt. 5.16.3.13 FIFO Operation Completed Flag (FIFO) The FIFO operation completed (FIFO) flag is set after the FIFO operation requested by writing to DAIDR2 as completed. FIFO is automatically cleared when DAIDR2 is read or written. This bit does not request an interrupt. 31:13 12 11 10 9 8 7 Reserved FIFO LCNE LCNF RCNE RCNF RCCELCRO 6 5 4 3 2 1 0 RCNFLCTU LCRORCRO LCTURCTU LCRS LCTS LCRSRCRS LCTSRCTS Bit Description 0 RCTS: Right Channel Transmit FIFO Service Request Flag (read-only) 0 — right channel transmit FIFO is more than half full (five or more entries filled) or DAI disabled 1 — right channel transmit FIFO is half full or less (four or fewer entries filled) and DAI operation is enabled, interrupt request signaled if not masked (if RCTM = 1) 1 RCRS: Right Channel Receive FIFO Service Request (read-only) 0 — right channel receive FIFO is less than half full (five or fewer entries filled) or DAI disabled 1 — right channel receive FIFO is half full or more (six or more entries filled) and DAI operation is enabled, interrupt request signaled if not masked (if RCRM = 1) 2 LCTS: Left Channel Transmit FIFO Service Request Flag (read-only) 0 — Left Channel transmit FIFO is more than half full or less (four or fewer entries filled) or DAI disabled. 1 — Left Channel transmit FIFO is half full or less (four or fewer entries filled) and DAI operation is enabled, interrupt request signaled if not masked (if LCTM = 1) 3 LCRS: 0 — Left Channel receive FIFO is less than half full (five or fewer entries filled) or DAI disabled. 1 — Left Channel receive FIFO is half full or more (six or more entries filled) and DAI operation is enabled, interrupt request signalled if not masked (if LCRM = 1) Table 51. DAI Control, Data and Status Register Locations DS453PP2 91 EP7209 Bit Description 4 Right Channel Transmit FIFO Underrun 0 — Right Channel transmit FIFO has not experienced an underrun 1 — Right Channel transmit logic attempted to fetch data from transmit FIFO while it was empty, request interrupt 5 RCRO: Right Channel Receive FIFO Overrun 0 — Right Channel receive FIFO has not experienced an overrun 1 — Right Channel receive logic attempted to place data into receive FIFO while it was full, request interrupt 6 LCTU: Left Channel Transmit FIFO Underrun 0 — Left Channel transmit FIFO has not experienced an underrun 1 — Left Channel transmit logic attempted to fetch data from transmit FIFO while it was empty, request interrupt 7 LCRO: Left Channel Receive FIFO Overrun 0 — Left Channel receive FIFO has not experienced an overrun 1 — Left Channel receive logic attempted to place data into receive FIFO while it was full, request interrupt 8 RCNF: Right Channel Transmit FIFO Not Full (read-only) 0 — Right Channel transmit FIFO is full 1 — Right Channel transmit FIFO is not full 9 RCNE: Right Channel Receive FIFO Not Empty (read-only) 0 — Right Channel receive FIFO is empty 1 — Right Channel receive FIFO is not empty 10 LCNF: LCNETelecom Transmit FIFO Not Full (read-only) 0 — Left Channel transmit FIFO is full 1 — Left Channel transmit FIFO is not full 11 LCNE: Left Channel Receive FIFO Not Empty (read-only) 0 — Left Channel receive FIFO is empty 1 — Left Channel receive FIFO is not empty 12 FIFO: FIFO Operation Completed (read-only) 0 — A FIFO Operation has not completed since the last time this bit was cleared 1 — THe FIFO Operation was completed 13 Reserved 14 Reserved 15 Reserved 16:31 Reserved Table 51. DAI Control, Data and Status Register Locations (cont.) 92 DS453PP2 EP7209 6. ELECTRICAL SPECIFICATIONS 6.1 Absolute Maximum Ratings DC Core, PLL, and RTC Supply Voltage 2.9 V DC I/O Supply Voltage (Pad Ring) 3.6 V DC Pad Input Current ±10 mA/pin; ±100 mA cumulative Storage Temperature, No Power –40°C to +125°C Table 52. absolute Maximum Ratings 6.2 Recommended Operating Conditions DC core, PLL, and RTC Supply Voltage 2.5 V ± 0.2 V DC I/O Supply Voltage (Pad Ring) 2.3V - 3.6V DC Input/Output Voltage O–I/O supply voltage Operating Temperature 0°C to +70°C Table 53. Recommended Operating Conditions 6.3 DC Characteristics All characteristics are specified at VDD = 2.5 volts and VSS = 0 volts over an operating temperature of 0°C to +70°C for all frequencies of operation. The current consumption figures relate to typical conditions at 2.5 V, 18.432 MHz operation with the PLL switched ‘on.’ Symbol Parameter Min Max Unit Conditions VIH CMOS input high voltage 1.7 VDD + 0.3 V VDD = 2.5 V VIL CMOS input low voltage -0.3 0.8 V VDD = 2.5 V VT+ Schmitt trigger positive going threshold 1.6 (Typ) 2.0 V VT- Schmitt trigger negative going threshold 0.8 1.2 (Typ) V Vhst Schmitt trigger hysteresis 0.1 0.4 V VIL to VIH VOH CMOS output high voltage Output drive 1 Output drive 2 VDD – 0.2 2.5 2.5 V V V IOH = 0.1 mA OH = 4 mA OH = 12 mA VOL CMOS output low voltage Output drive 1 Output drive 2 0.3 0.5 0.5 V V V IOL = –0.1 mA OL = –4 mA OL = –12 mA 1 µA VIN = VDD or GND VOUT = VDD or GND IIN Input leakage current IOZ Output tri-state leakage current* 25 100 µA CIN Input capacitance 8 10 pF Table 54. DC Characteristics DS453PP2 93 EP7209 Symbol Parameter COUT CI/O Min Max Unit Output capacitance 8 10 pF Transceiver capacitance 8 10 pF Startup current consumption IDDstartup µA Initial 100 ms from power up, 32 kHz oscillator not stable, POR signal at VIL, all other I/O static, VIH = VDD ± 0.1 V, VIL = GND ± 0.1 V µA Just 32 kHz oscillator running, all other I/O static, VIH = VDD ± 0.1 V, VIL = GND ± 0.1 V mA Both oscillators running, CPU static, LCD refresh active, VIH = VDD ± 0.1 V, VIL = GND ± 0.1 V Standby current consumption IDDstandby 4 Idle current consumption At 13 MHz At 18 MHz At 36 MHz IDDidle IDDoperating 4.2 6 12 Operating current consumption At 13 MHz At 18 MHz At 36 MHz At 49 MHz At 74 MHz All system active, running typical program 14 20 40 50 68 mA Standby supply voltage VDDstandby NOTE: Conditions TBD V Minimum standby voltage for state retention and RTC operation only All power dissipation values can be derived from taking the particular IDD current and multiplying by 2.5 V. The RTC of the EP7209 should be brought up at room temperature. This is required because the RTC OSC will NOT function properly if it is brought up at –40°C. Once operational, it will continue to operate down to –40°C. A typical design will provide 3.3 V to the I/O supply (i.e., VDDIO), and 2.5 V to the remaining logic. This is to allow the I/O to be compatible with 3.3 V powered external logic (i.e., 3.3 V DRAMs). Pull-up current = 50 µA typical at VDD = 3.3 volts. Table 54. DC Characteristics (cont.) 94 DS453PP2 EP7209 6.4 AC Characteristics All characteristics are specified at VDD = 2.3 to 2.7 volts and VSS = 0 volts over an operating temperature of 0°C to +70°C. Those characteristics marked with a # will be significantly different for 13 MHz mode because the EXPCLK is provided as an input rather than generated internally. These timings are estimated at present. The timing values are referenced to 1/2 VDD. Symbol Parameter 13 MHz Min Max 18/36 MHz Min Units Max t1 Falling CS to data bus Hi-Z 0 35 0 25 ns t2 Address change to valid write data 0 45 0 35 ns t3 DATA in to falling EXPCLK setup time 0 # — 18 — ns t4 DATA in to falling EXPCLK hold time 10 # — 0 — ns t5 EXPRDY to falling EXPCLK setup time 0# — 18 — ns t6 Falling EXPCLK to EXPRDY hold time 10 # 50 0 50 ns t7 Rising nMWE to data invalid hold time 10 — 5 — ns t8 Sequential data valid to falling NMWE setup time –10 10 –10 10 ns t15 LCD CL2 low time 80 3,475 80 3,475 ns t16 LCD CL2 high time 80 3,475 80 3,475 ns t17 LCD falling CL[2] to rising CL[1] delay 0 25 0 25 ns t18 LCD falling CL[1] to rising CL[2] 80 3,475 80 3,475 ns t19 LCD CL[1] high time 80 3,475 80 3,475 ns t20 LCD falling CL[1] to falling CL[2] 200 6,950 200 6,950 ns t21 LCD falling CL[1] to FRM toggle 300 10,425 300 10,425 ns t22 LCD falling CL[1] to M toggle –10 20 –10 20 ns t23 LCD rising CL[2] to display data change –10 20 –10 20 ns t24 Falling EXPCLK to address valid — 33 # — 5 ns t25 Data valid to falling nMWE for non sequential access only 5 — 5 — ns t31 SSICLK period (slave mode) 0 512 0 512 kHz t32 SSICLK high 925 1025 925 1025 ns t33 SSICLK low 925 1025 925 1025 ns t34 SSICLK rise/fall time 7 7 ns t35 SSICLK rising to RX and/or TX frame sync 528 528 ns t36 SSICLK rising edge to frame sync low 448 448 ns t37 SSICLK rising edge to TX data valid 80 80 ns t38 SSIRXDA data set-up time 30 30 ns t39 SSIRXDA data hold time 40 40 ns t40 SSITXFR and/or SSIRXFR period 750 750 ns The values for 36 MHz include 1 wait state, the 18 MHz values have 0 wait states. Table 55. AC Timing Characteristics DS453PP2 95 EP7209 Symbol Characteristics 13 MHz Min Max 18 MHz Min Max 36 MHz Min Units Max tnCSRD Negative strobe (nCS[0:5]) zero wait state read access time 120 70 35 ns tnCSWR Negative strobe (nCS[0:5]) zero wait state write access time 120 70 35 ns tEXBST Sequential expansion burst mode read access time 55 35 35 ns The values for 36 MHz include 1 wait state, the 18 MHz values have 0 waits tates. Table 56. Timing Characteristics 96 DS453PP2 EP7209 eXPCLK tNCSRD nCS[5:0] nMOE A[27:0] WORD t1 tADRD tPCSRD D[31:0] t3 t4 Data in Bus held t5 t3 t4 Data in t6 eXPRDY NOTES: 1) tnCSRD = 50 ns at 36.864 MHz 70 ns at 18.432 MHz 120 ns at 13.0 MHz Maximum values for minimum wait states. This time can be extended by integer multiples of the clock period (27 ns at 36 MHz, 54 ns at 18.432 MHz, and 77 ns at 1 MHz), by either driving EXPRDY low and/or by programming a number of wait states. EXPRDY is sampled on the falling edge of EXPCLK before the data transfer. If low at this point, the transfer is delayed by one clock period where EXPRDY is sampled again. EXPCLK need not be referenced when driving EXPRDY, but is shown for clarity. 2) Consecutive reads with sequential access enabled are identical except that the sequential access wait state field is used to determine the number of wait states, and no idle cycles are inserted between successive non-sequential ROM/expansion cycles. This improves performance so the SQAEN bit should always be set where possible. 3) tnCSRD = tADRD = tPCSRD Figure 13. Consecutive Memory Read Cycles with Minimum Wait States DS453PP2 97 EP7209 EXPCLK nCS[5:0] nMOE A[27:4] tEXBST 0 tEXBST 4 8 WORD t1 tEXRD D[31:0] t3 t4 Data in Bus held t5 t4 t3 Data in t3 t4 Data in t6 EXPRDY NOTES: 1) tEXBST = 35 ns at 36.864 MHz 35 ns at 18.432 MHz 55 ns at 13.0 MHz (Value for 36.864 MHz assumes 1 wait state.) Maximum values for minimum wait states. This time can be extended by integer multiples of the clock period (27 nsec at 36 MHz, 54 nsec at 18.432 MHz and 77 ns at 13 MHz), by either driving EXPRDY low and/or by programming a number of wait states. EXPRDY is sampled on the falling edge of EXPCLK before the data transfer. If low at this point, the transfer is delayed by one clock period where EXPRDY is sampled again. EXPCLK need not be referenced when driving EXPRDY, but is shown for clarity. 2) Consecutive reads with sequential access enabled are identical except that the sequential access wait state field is used to determine the number of wait states, and no idle cycles are inserted between successive non-sequential ROM/expansion cycles. This improves performance so the SQAEN bit should always be set where possible. Figure 14. Sequential Page Mode Read Cycles with Minimum Wait States 98 DS453PP2 EP7209 eXPCLK tnCSWR nCS[5:0] t8 tADWR nMWE A[27:0] WORD t2 D[31:0] Bus held t7 t2 Write data Write data t6 t5 EXPRDY NOTES: 1) tnCSWR = 35 nsec at 36.864 MHz 70 ns at 18.432 MHz 120 ns at 13.0 MHz Maximum values for minimum wait states. This time can be extended by integer multiples of the clock period (27 nsec at 36 MHz, 54 nsec at 18.432 MHz, and 77 nsec at 13 MHz), by either driving EXPRDY low and/or by programming a number of wait states. EXPRDY is sampled on the falling edge of EXPCLK before the data transfer. If low at this point, the transfer is delayed by one clock period where EXPRDY is sampled again. EXPCLK need not be referenced when driving EXPRDY, but is shown for clarity. 2) Consecutive reads with sequential access enabled are identical except that the sequential access wait state field is used to determine the number of wait states, and no idle cycles are inserted between successive non-sequential ROM/expansion cycles. This improves performance so the SQAEN bit should always be set where possible. 3) Zero wait states for sequential writes is not permitted for memory devices which use nMWE pin, as this cannot be driven with valid timing under zero wait state conditions. Figure 15. Consecutive Memory Write Cycles with Minimum Wait States DS453PP2 99 EP7209 t20 t15 t16 CL[2] t17 t19 t18 t21 CL[1] FRM t22 M t23 DD[3:0] NOTES: 1) The figure shows the end of a line. 2) If FRM is high during the CL[1] pulse, this marks the first line in the display. 3) CL[2] low time is doubled during the CL[1] high pulse Figure 16. LCD Controller Timings 1 2 DI9 DI8 3 4 5 7 6 8 9 DI1 DI0 10 11 12 13 14 15 22 23 DO1 DO0 ADCCLK (SCLK) nADCCS (nRFS/TFS) ADCIN (Din) DI7 DI6 DI5 DI4 DI3 DI2 ADCOUT (Dout) DO9 DO8 Figure 17. SSI Interface for AD7811/2 100 DS453PP2 EP7209 1 2 DI7 DI6 3 4 5 6 7 8 9 10 11 12 13 14 15 24 25 ADCCLK (SCLK) nADCCS (nCS) ADCIN (Din) DI5 DI4 DI3 DI2 DI1 ADCOUT (Dout) DI0 DO15 DO14 DO13 DO12 DO11 DO10 DO1 DO0 Figure 18. SSI Timing Interface for MAX148/9 t33 t31 t32 SSICLK t40 t35 SSI RX/TXFR t36 t37 D7 SSITXDA t38 SSIRXDA D2 D1 D0 D2 D1 D0 t39 D7 Figure 19. SSI2 Interface Timings DS453PP2 101 EP7209 6.5 I/O Buffer Characteristics All I/O buffers on the EP7209 are CMOS threshold input bidirectional buffers except the oscillator and power pads. For signals that are nominally inputs, the output buffer is only enabled during pin test mode. All output buffers are tristated during system (hi-Z) test mode. All buffers have a standard CMOS threshold input stage (apart from the Schmitt triggered inputs) and CMOS slew rate controlled output stages to reduce system noise. Table 57 defines the I/O buffer output characteristics which will apply across the full range of temperature and voltage (i.e., these values are for 3.3 V, +70°C). All propagation delays are specified at 50% VDD to 50% VDD, all rise times are specified as 10% VDD to 90% VDD and all fall times are specified as 90% VDD to 10% VDD. Buffer Type Drive Current Propagation Delay (Max) Rise Time (Max) Fall Time (Max) Load I/O strength 1 ±4 mA 7 14 14 50 pF I/O strength 2 ±12 mA 5 6 6 50 pF Table 57. I/O Buffer Output Characteristics 6.6 Pin No. JTAG Bandary Scan Signal Ordering Signal Type Strength Reset State 1 High 1 nCS[5] Out 2 VDDIO Pad Pwr 3 VSSIO Pad Gnd 4 EXPCLK I/O 1 5 WORD Out 1 Low 6 WRITE Out 1 Low 7 RUN/CLKEN I/O 1 Low 8 EXPRDY In 1 9 TXD[2] Out 1 10 RXD[2] In 11 TDI In 12 VSSIO Pad Gnd 13 PB[7] I/O 1 Input 14 PB[6] I/O 1 Input 15 PB[5] I/O 1 Input 16 PB[4] I/O 1 Input 17 PB[3] I/O 1 Input 18 PB[2] I/O 1 Input High with p/u* Table 58. 208-Pin LQFP Numeric Pin Listing Pin No. Signal Type Strength Reset State 19 PB[1]/ PRDY2 I/O 1 Input 20 PB[0]/ PRDY1 I/O 1 Input 21 VDDIO Pad Pwr 22 TDO Out 1 Tristate 23 PA[7] I/O 1 Input 24 PA[6] I/O 1 Input 25 PA[5] I/O 1 Input 26 PA[4] I/O 1 Input 27 PA[3] I/O 1 Input 28 PA[2] I/O 1 Input 29 PA[1] I/O 1 Input 30 PA[0] I/O 1 Input 31 LEDDRV Out 1 Low 32 TXD[1] Out 1 High 33 VSSIO Pad Gnd 1 High 34 PHDIN In 35 CTS In 36 RXD[1] In Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) 102 DS453PP2 EP7209 Pin No. Signal Type 37 DCD In 38 DSR In 39 nTEST[1] In 40 nTEST[0] In 41 EINT[3] 42 Strength Pin No. Signal Type 71 VSSCORE Core Gnd With p/u* 72 VDDCORE Core Pwr With p/u* 73 VSSIO Pad Gnd In 74 VDDIO Pad Pwr nEINT[2] In 75 DRIVE[1] I/O 1 43 nEINT[1] In High/ Low 44 nEXTFIQ In 76 DRIVE[0] I/O 1 High/ Low 45 PE[2]/ CLKSEL I/O 77 ADCCLK Out 1 Low 78 ADCOUT Out 1 Low 46 PE[1]/ BOOTSEL[1] I/O 1 Input 79 SMPCLK Out 1 Low 47 PE[0]/ BOOTSEL[0] I/O 1 Input 48 VSSRTC 49 RTCOUT 50 1 Reset State Input Strength Reset State 80 FB[1] In 81 VSSIO Pad Gnd RTC Gnd 82 FB[0] In Out 83 COL[7] Out 1 High RTCIN In 84 COL[6] Out 1 High 51 VSSRTC RTC power 85 COL[5] Out 1 High 86 COL[4] Out 1 High 52 N/C 87 COL[3] Out 1 High 53 PD[7] I/O 1 Low 88 COL[2] Out 1 High 54 PD[6] I/O 1 Low 89 VDDIO Pad Pwr 55 PD[5] I/O 1 Low 90 TCLK In 56 PD[4] I/O 1 Low 91 COL[1] Out 1 High 57 VDDIO Pad Pwr 92 COL[0] Out 1 High 58 TMS In with p/u* 93 BUZ Out 1 Low 59 PD[3] I/O 1 Low 94 D[31] I/O 1 Low 60 PD[2] I/O 1 Low 95 D[30] I/O 1 Low 61 PD[1] I/O 1 Low 96 D[29] I/O 1 Low 62 PD[0]/ LEDFLSH I/O 1 Low 97 D[28] I/O 1 Low 63 SSICLK I/O 1 Input 98 VSSIO Pad Gnd 64 VSSIO Pad Gnd 99 A[27] Out 2 Low 65 SSITXFR I/O 1 Low 100 D[27] I/O 1 Low 66 SSITXDA Out 1 Low 101 A[26] Out 2 Low 67 SSIRXDA In 102 D[26] I/O 1 Low 68 SSIRXFR I/O 103 A[25] Out 2 Low 69 ADCIN In 104 D[25] I/O 1 Low 70 nADCCS Out 105 HALFWORD Out 1 Low 106 A[24] Out 1 Low 107 VDDIO Pad Pwr Input 1 High Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) — Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 103 EP7209 Pin No. Signal Type Strength Reset State Pin No. Signal 108 VSSIO Pad Gnd 109 D[24] 110 111 Type Strength Reset State — 147 D[8] I/O 1 Low I/O 1 Low 148 A[7] Out 1 Low A[23] Out 1 Low 149 VSSIO Pad Gnd D[23] I/O 1 Low 150 D[7] I/O 1 Low 112 A[22] Out 1 Low 151 nBATCHG In 113 D[22] I/O 1 Low 152 nEXTPWR In 114 A[21] Out 1 Low 153 BATOK In 115 D[21] I/O 1 Low 154 nPOR In 116 VSSIO Pad Gnd 155 A[20] Out 1 Low nMEDCHG/ nBROM In 117 118 D[20] I/O 1 Low 156 nURESET In 119 A[19] Out 1 Low 157 VDDOSC Osc Pwr 120 D[19] I/O 1 Low 158 MOSCIN Osc MOSCOUT Osc Schmitt Schmitt 121 A[18] Out 1 Low 159 122 D[18] I/O 1 Low 160 VSSOSC Osc Gnd 123 VDDIO Pad Pwr 161 WAKEUP In 124 VSSIO Pad Gnd 162 nPWRFL In 163 A[6] Out 1 Low Schmitt 125 nTRST In 126 A[17] Out 1 Low 164 D[6] I/O 1 Low 127 D[17] I/O 1 Low 165 A[5] Out 1 Low 128 A[16] Out 1 Low 166 D[5] I/O 1 Low VDDIO Pad Pwr 1 Low 129 D[16] I/O 1 Low 167 130 A[15]] Out 1 Low 168 VSSIO Pad Gnd 131 D[15] I/O 1 Low 169 A[4] Out 132 A[14] Out 1 Low 170 D[4] I/O 1 Low A[3] Out 2 Low 133 D[14] I/O 1 Low 171 134 A[13] Out 1 Low 172 D[3] I/O 1 Low 135 D[13] I/O 1 Low 173 A[2] Out 2 Low 136 A[12] Out 1 Low 174 VSSIO Pad Gnd D[2] I/O 1 Low 137 D[12] I/O 1 Low 175 138 A[11] Out 1 Low 176 A[1] Out 1 Low 139 VDDIO Pad Pwr 177 D[1] I/O 1 Low 140 VSSIO Pad Gnd 178 A[0] Out 1 Low D[0] I/O 1 Low 1 Low 141 D[11] I/O 1 Low 179 142 A[10] Out 1 Low 180 VSS CORE Core Gnd 143 D[10] I/O 1 Low 181 VDD CORE Core Pwr 144 A[9] Out 1 Low 182 VSSIO Pad Gnd VDDIO Pad Pwr CL[2] Out 145 D[9] I/O 1 Low 183 146 A[8] Out 1 Low 184 Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) 104 Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 EP7209 Pin No. Signal Type Strength Reset State 185 CL[1] Out 1 Low 186 FRM Out 1 Low 187 M Out 1 Low 188 DD[3] I/O 1 Low 1 Low 189 DD[2] I/O 190 VSSIO Pad Gnd 191 DD[1] I/O 1 Low 192 DD[0] I/O 1 Low 193 N/C 194 N/C 195 N/C 196 N/C 197 VDDIO Pad Pwr 198 VSSIO Pad Gnd 199 N/C 200 N/C 201 nMWE Out 1 High 202 nMOE Out 1 High 203 VSSIO Pad Gnd 204 nCS[0] Out 1 High 205 nCS[1] Out 1 High 206 nCS[2] Out 1 High 207 nCS[3] Out 1 High 208 nCS[4] Out 1 High NOTE: ‘With p/u’ means with internal pull-up on the pin. Table 58. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 105 EP7209 7. TEST MODES 7.2 The EP7209 supports a number of hardware activated test modes, these are activated by the pin combinations shown in Table 59. All latched signals will only alter test modes while NPOR is low, their state is latched on the rising edge of NPOR. This allows these signals to be used normally during various test modes. This mode is selected by nTEST[0] = 0, nTEST[1] = 1, Latched nURESET = 0 Within each test mode, a selection of pins is used as multiplexed outputs or inputs to provide/monitor the test signals unique to that mode. 7.1 Oscillator and PLL Bypass Mode This mode is nTEST[1] = 0. selected by nTEST[0] = 1, In this mode all the internal oscillators and PLL are disabled and the appropriate crystal oscillator pins become the direct external oscillator inputs bypassing the oscillator and PLL. MOSCIN must be driven by a 36.864 MHz clock source and RTCIN by a 32.768 kHz source. Test Mode Oscillator and PLL Test Mode This test mode will enable the main oscillator and it will output various buffered clock and test signals derived from the main oscillator, PLL, and 32-kHz oscillator. All internal logic in the EP7209 will be static and isolated from the oscillators, with the exception of the 6-bit ripple counter used to generate 576 kHz and the Real Time Clock divide chain. Port A is used to drive the inputs of the PLL directly, and the various clock and PLL outputs are monitored on the COL pins. Table 60 defines the EP7209 signal pins used in this test mode. This mode is only intended to allow test of the oscillators and PLL. Note that these inputs are inverted before being passed to the PLL to ensure that the default state of the port (all zero) maps onto the correct default state of the PLL (TSEL = 1, XTALON = 1, PLLON = 1, D0 = 0, D1 = 1, PLLBP = 0). This state will produce the correct frequencies as shown in Table 60. Any other combinations are for testing the oscillator and PLL and should not be used incircuit. Latched nMEDCHG Latched PE[0] Latched PE[1] Latched nURESET nTEST[0] nTEST[1] Normal operation (32-bit boot) 1 0 0 X 1 1 Normal operation (8-bit boot) 1 1 0 X 1 1 Normal operation (16-bit boot) 1 0 1 X 1 1 Alternative test ROM boot 0 X X X 1 1 Oscillator / PLL bypass X X X X 1 0 Oscillator / PLL test mode X X X 0 0 1 ICE Mode X X X 1 0 0 System test (all HiZ) X X X 0 0 0 Table 59. EP7209 Hardware Test Modes 106 DS453PP2 EP7209 Signal I/O Pin Function TSEL * I PA5 PLL test mode XTLON * I PA4 Enable to oscillator circuit PLLON * I PA3 Enable to PLL circuit PLLBP I PA0 Bypasses PLL RTCCLK O COL0 Output of RTC oscillator CLK1 O COL1 1 Hz clock from RTC divider chain OSC36 O COL2 36 MHz divided PLL main clock CLK576K O COL4 576 KHz divided from above VREF O COL6 Test clock output for PLL Table 60. Oscillator and PLL Test Mode Signals 7.3 Debug/ICE Test Mode This mode is selected by nTEST0 = 0, nTEST1 = 0, Latched nURESET = 1. Selection of this mode enables the debug mode of the ARM720T. By default, this is disabled which saves approximately 3% on power. 7.4 Hi-Z (System) Test Mode This mode selected by nTEST0 = 0, nTEST1 = 0, Latched nURESET = 0. This test mode asynchronously disables all output buffers on the EP7209. This has the effect of removing the EP7209 from the PCB so that other devices on the PCB can be in-circuit tested. The internal state of the EP7209 is not altered directly by this test mode. 7.5 Software Selectable Test Functionality When bit 11 of the SYSCON register is set high, internal peripheral bus register accesses are output on the main address and data buses as though they were external accesses to the address space addressed by nCS[5]. Hence, nCS[5] takes on a dual role, it will be active as the strobe for internal accesses and for any accesses to the standard address range for nCS[5]. Additionally, in this mode, the internal signals shown in Table 61 are multiplexed out of the device on port pins. Signal I/O Pin Function CLK O PE0 Waited clock to CPU nFIQ O PE1 nFIQ interrupt to CPU nIRQ O PE2 nIRQ interrupt to CPU Table 61. Software Selectable Test Functionality This test is not intended to be used when LCD DMA accesses are enabled. This is due to the fact that it is possible to have internal peripheral bus activity simultaneously with a DMA transfer. This would cause bus contention to occur on the external bus. The ‘Waited clock to CPU’ is an internally ANDed source that generates the actual CPU clock. Thus, it is possible to know exactly when the CPU is being clocked by viewing this pin. The signals nFIQ and nIRQ are the two output signals from the internal interrupt controller. They are input directly into the ARM720T processor. DS453PP2 107 EP7209 8. PIN INFORMATION 208-Pin LQFP Pin Diagram 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 NURESET NMEDCHG/NBROM NPOR BATOK NEXTPWR NBATCHG D[7] VSSIO A[7] D[8] A[8] D[9] A[9] D[10] A[10] D[11] VSSIO VDDIO A[11] D[12] A[12] D[13] A[13] D[14] A[14] D[15] A[15] D[16] A[16] D[17] A[17] NTRST VSSIO VDDIO D[18] A[18] D[19] A[19] D[20] A[20] VSSIO D[21] A[21] D[22] A[22] D[23] A[23] D[24] VSSIO VDDIO A[24] HALFWORD 8.1 EP7209 208-Pin LQFP (Top View) 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 D[25] A[25] D[26] A[26] D[27] A[27] VSSIO D[28] D[29] D[30] D[31] BUZ COL[0] COL[1] TCLK VDDIO COL[2] COL[3] COL[4] COL[5] COL[6] COL[7] FB[0] VSSIO FB[1] SMPCLK ADCOUT ADCCLK DRIVE[0] DRIVE[1] VDDIO VSSIO VDDCORE VSSCORE NADCCS ADCIN SSIRXFR SSIRXDA SSITXDA SSITXFR VSSIO SSICLK PD[0]/LEDFLSH PD[1] PD[2] PD[3] TMS VDDIO PD[4] PD[5] PD[6] PD[7] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 NCS[5] VDDIO VSSIO EXPCLK WORD WRITE RUN/CLKEN EXPRDY TXD[2] RXD[2] TDI VSSIO PB[7] PB[6] PB[5] PB[4] PB[3] PB[2] PB[1]/PRDY[2] PB[0]/PRDY[1] VDDIO TDO PA[7] PA[6] PA[5] PA[4] PA[3] PA[2] PA[1] PA[0] LEDDRV TXD[1] VSSIO PHDIN CTS RXD[1] DCD DSR NTEST[1] NTEST[0] EINT[3] NEINT[2] NEINT[1] NEXTFIQ PE[2]/CLKSEL PE[1]BOOTSEL[1] PE[0]BOOTSEL[0] VSSRTC RTCOUT RTCIN VDDRTC N/C VDDOSC MOSCIN MOSCOUT VSSOSC WAKEUP NPWRFL A[6] D[6] A[5] D[5] VDDIO VSSIO A[4] D[4] A[3] D[3] A[2] VSSIO D[2] A[1] D[1] A[0] D[0] VSSCORE VDDCORE VSSIO VDDIO CL[2] CL[1] FRM M DD[3] DD[2] VSSIO DD[1] DD[0] N/C N/C N/C N/C VDDIO VSSIO N/C N/C NMWE NMOE VSSIO NCS[0] NCS[1] NCS[2] NCS[3] NCS[4] Notes: 1) For package specifications, please see 208--Pin LQFP Package Outline Drawing on page 117 2) N/C should not be grounded but left as no connects Figure 20. 208-Pin LQFP (Low Profile Quad Flat Pack) Pin Diagram 108 DS453PP2 EP7209 8.2 208-Pin LQFP Numeric Pin Listing Pin No. Signal Type Strength 1 Reset State High Pin No. Signal Type 36 RXD[1] In 37 DCD In Strength 1 nCS[5] Out 2 VDDIO Pad Pwr 38 DSR In 3 VSSIO Pad Gnd 39 nTEST[1] In With p/u* 4 EXPCLK I/O 1 40 nTEST[0] In With p/u* EINT[3] In Reset State 5 WORD Out 1 Low 41 6 WRITE Out 1 Low 42 nEINT[2] In 7 RUN/CLKEN I/O 1 Low 43 nEINT[1] In 8 EXPRDY In 1 44 nEXTFIQ In 45 PE[2]/ CLKSEL I/O 1 Input 46 PE[1]/ BOOTSEL[1] I/O 1 Input 47 PE[0]/ BOOTSEL[0] I/O 1 Input 9 TXD[2] Out 1 High 10 RXD[2] In 11 TDI In 12 VSSIO Pad Gnd 13 PB[7] I/O 1 Input 14 PB[6] I/O 1 Input 48 VSSRTC RTC Gnd 15 PB[5] I/O 1 Input 49 RTCOUT Out 16 PB[4] I/O 1 Input 50 RTCIN In 17 PB[3] I/O 1 Input 51 VSSRTC 18 PB[2] I/O 1 Input RTC power 19 PB[1]/ PRDY2 I/O 1 Input 20 PB[0]/ PRDY1 I/O 1 Input 21 VDDIO Pad Pwr 22 TDO Out 1 Tristate 23 PA[7] I/O 1 Input 24 PA[6] I/O 1 Input 25 PA[5] I/O 1 Input 26 PA[4] I/O 1 Input 27 PA[3] I/O 1 Input 28 PA[2] I/O 1 29 PA[1] I/O 30 PA[0] 31 LEDDRV 32 33 with p/u* 52 N/C 53 PD[7] I/O 1 Low 54 PD[6] I/O 1 Low 55 PD[5] I/O 1 Low 1 Low 56 PD[4] I/O 57 VDDIO Pad Pwr 58 TMS In with p/u* 59 PD[3] I/O 1 Low 60 PD[2] I/O 1 Low 61 PD[1] I/O 1 Low Input 62 PD[0]/ LEDFLSH I/O 1 Low 1 Input 63 SSICLK I/O 1 Input I/O 1 Input 64 VSSIO Pad Gnd Out 1 Low 65 SSITXFR I/O 1 Low TXD[1] Out 1 High 66 SSITXDA Out 1 Low VSSIO Pad Gnd 1 High 67 SSIRXDA In 34 PHDIN In 68 SSIRXFR I/O 35 CTS In 69 ADCIN In Table 62. 208-Pin LQFP Numeric Pin Listing Input Table 62. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 109 EP7209 Pin No. Signal Type Strength Reset State Pin No. Signal 70 Type Strength Reset State nADCCS Out 1 High 107 VDDIO Pad Pwr — 71 VSSCORE Core Gnd 108 VSSIO Pad Gnd — 109 D[24] I/O 1 Low 72 VDDCORE Core Pwr 110 A[23] Out 1 Low 73 VSSIO Pad Gnd 111 D[23] I/O 1 Low 74 VDDIO Pad Pwr 112 A[22] Out 1 Low 75 DRIVE[1] I/O 2 High/ Low 113 D[22] I/O 1 Low A[21] Out 1 Low DRIVE[0] I/O 2 High/ Low 114 76 115 D[21] I/O 1 Low VSSIO Pad Gnd 77 ADCCLK Out 1 Low 116 78 ADCOUT Out 1 Low 117 A[20] Out 1 Low 79 SMPCLK Out 1 Low 118 D[20] I/O 1 Low 80 FB[1] In 119 A[19] Out 1 Low D[19] I/O 1 Low 81 VSSIO Pad Gnd 120 82 FB[0] In 121 A[18] Out 1 Low 83 COL[7] Out 1 High 122 D[18] I/O 1 Low 84 COL[6] Out 1 High 123 VDDIO Pad Pwr VSSIO Pad Gnd 1 Low 85 COL[5] Out 1 High 124 86 COL[4] Out 1 High 125 nTRST In 87 COL[3] Out 1 High 126 A[17] Out 88 COL[2] Out 1 High 127 D[17] I/O 1 Low A[16] Out 1 Low 89 VDDIO Pad Pwr 128 90 TCLK In 129 D[16] I/O 1 Low 91 COL[1] Out 1 High 130 A[15]] Out 1 Low 92 COL[0] Out 1 High 131 D[15] I/O 1 Low A[14] Out 1 Low 93 BUZ Out 1 Low 132 94 D[31] I/O 1 Low 133 D[14] I/O 1 Low 95 D[30] I/O 1 Low 134 A[13] Out 1 Low 96 D[29] I/O 1 Low 135 D[13] I/O 1 Low Low 136 A[12] Out 1 Low 137 D[12] I/O 1 Low Out 1 Low 97 D[28] I/O 1 98 VSSIO Pad Gnd 99 A[27] Out 2 Low 138 A[11] 100 D[27] I/O 1 Low 139 VDDIO Pad Pwr VSSIO Pad Gnd 101 A[26] Out 2 Low 140 102 D[26] I/O 1 Low 141 D[11] I/O 1 Low 103 A[25] Out 2 Low 142 A[10] Out 1 Low 104 D[25] I/O 1 Low 143 D[10] I/O 1 Low 105 HALFWORD Out 1 Low 144 A[9] Out 1 Low Low 145 D[9] I/O 1 Low 106 A[24] Out 1 Table 62. 208-Pin LQFP Numeric Pin Listing (cont.) 110 Table 62. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 EP7209 Signal Type Strength Reset State Pin No. Signal Type Strength Reset State 146 A[8] Out 1 Low 184 CL[2] Out 1 Low 147 D[8] I/O 1 Low 185 CL[1] Out 1 Low 148 A[7] Out 1 Low 186 FRM Out 1 Low 149 VSSIO Pad Gnd 187 M Out 1 Low 150 D[7] I/O 188 DD[3] I/O 1 Low 151 nBATCHG In 189 DD[2] I/O 1 Low 152 nEXTPWR In 190 VSSIO Pad Gnd 153 BATOK In 191 DD[1] I/O 1 Low 154 nPOR In 192 DD[0] I/O 1 Low 155 nMEDCHG/ nBROM In 193 N/C 194 N/C 156 nURESET In 195 N/C 157 VDDOSC Osc Pwr 196 N/C 158 MOSCIN Osc 197 VDDIO Pad Pwr 159 MOSCOUT Osc 198 VSSIO Pad Gnd 160 VSSOSC Osc Gnd 199 N/C 161 WAKEUP In 162 nPWRFL In 163 A[6] Out 1 164 D[6] I/O 165 A[5] 166 Pin No. 1 Low Schmitt Schmitt Schmitt 200 N/C 201 nMWE Out 1 High Low 202 nMOE Out 1 High 1 Low 203 VSSIO Pad Gnd Out 1 Low 204 nCS[0] Out 1 High D[5] I/O 1 Low 205 nCS[1] Out 1 High 167 VDDIO Pad Pwr 206 nCS[2] Out 1 High 168 VSSIO Pad Gnd 207 nCS[3] Out 1 High 169 A[4] Out 1 Low 208 nCS[4] Out 1 High 170 D[4] I/O 1 Low 171 A[3] Out 2 Low 172 D[3] I/O 1 Low 2 Low 173 A[2] Out 174 VSSIO Pad Gnd 175 D[2] I/O 1 Low 176 A[1] Out 2 Low 177 D[1] I/O 1 Low 178 A[0] Out 2 Low 179 D[0] I/O 1 Low 180 VSS CORE Core Gnd 181 VDD CORE Core Pwr 182 VSSIO Pad Gnd 183 VDDIO Pad Pwr NOTE: ‘With p/u’ means with internal pull-up on the pin. Table 62. 208-Pin LQFP Numeric Pin Listing (cont.) Table 62. 208-Pin LQFP Numeric Pin Listing (cont.) DS453PP2 111 EP7209 8.3 256-Pin PBGA Pin Diagram 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H J K L M N P R T 256-Ball PBGA (Bottom View) NOTE: 112 For package specifications, please see 256-Ball PBGA Dimensions page 118 DS453PP2 EP7209 8.4 256-Ball PBGA Ball Listing Ball Location Name Type Ball Location Name Type C5 VSSIO Pad ground VSSIO Pad ground A1 VDDIO Pad power C6 A2 nCS[4] O C7 VSSIO Pad ground A3 nCS[1] O C8 VDDIO Pad power A4 NC No Connect C9 VSSIO Pad ground VSSIO Pad ground A5 NC No Connect C10 A6 DD[1] O C11 VSSIO Pad ground A7 M O C12 VDDIO Pad power A8 VDDIO Pad power C13 VSSIO Pad ground VSSIO Pad ground A9 D[0] I/O C14 A10 D[2] I/O C15 nPOR I A11 A[3] O C16 nEXTPWR I A12 VDDIO Pad power D1 WRITE O EXPRDY I A13 A[6] O D2 A14 MOSCOUT O D3 VSSIO Pad ground A15 VDDOSC Oscillator power D4 VDDIO Pad power A16 VSSIO Pad ground D5 nCS[2] O nMWE O B1 nCS[5] O D6 B2 VDDIO Pad power D7 N/C No Connect B3 nCS[3] O D8 CL[2] O B4 nMOE O D9 VSSRTC Core ground D[4] I/O B5 VDDIO Pad power D10 B6 N/C No Connect D11 nPWRFL I B7 DD[2] O D12 MOSCIN I B8 CL[1] O D13 VDDIO Pad power VSSIO Pad ground B9 VDDCORE Core power D14 B10 D[1] I/O D15 D[7] I/O B11 A[2] O D16 D[8] I/O B12 A[4] O E1 RXD[2] I PB[7] I B13 A[5] O E2 B14 WAKEUP I E3 TDI I B15 VDDIO Pad power E4 WORD O B16 nURESET I E5 VSSIO Pad ground nCS[0] O C1 VDDIO Pad power E6 C2 EXPCLK I E7 NC No Connect C3 VSSIO Pad ground E8 FRM O C4 VDDIO Pad power E9 A[0] O Table 63. 256-Ball PBGA Ball Listing Table 63. 256-Ball PBGA Ball Listing (cont.) DS453PP2 113 EP7209 Ball Location Name Type Ball Location Name Type E10 D[5] I/O H1 PA[7] I E11 VSSOSC Oscillator ground H2 PA[5] I E12 VSSIO Pad ground H3 VSSIO Pad ground E13 nMEDCHG/nBROM I H4 PA[4] I E14 VDDIO Pad power H5 PA[6] I E15 D[9] I/O H6 PB[0]/PRDY[1] I E16 D[10] I/O H7 PB[2] I F1 PB[5] I H8 VSSRTC RTC ground F2 PB[3] I H9 VSSRTC RTC ground F3 VSSIO Pad ground H10 A[10] O F4 TXD[2] O H11 A[11] O F5 RUN/CLKEN O H12 A[12] O F6 VSSIO Pad ground H13 A[13] O F7 NC No Connect H14 VSSIO Pad ground F8 DD[3] O H15 D[14] I/O F9 A[1] O H16 D[15] I/O F10 D[6] I/O J1 PA[3] I F11 VSSRTC RTC ground J2 PA[1] I F12 BATOK I J3 VSSIO Pad ground F13 nBATCHG I J4 PA[2] I F14 VSSIO Pad ground J5 PA[0] I F15 D[11] I/O J6 TXD[1] O F16 VDDIO Pad power J7 CTS I G1 PB[1]/PRDY[2] I J8 VSSRTC RTC ground G2 VDDIO Pad power J9 VSSRTC RTC ground G3 TDO O J10 A[17] O G4 PB[4] I J11 A[16] O G5 PB[6] I J12 A[15] O G6 VSSRTC Core ground J13 A[14] O G7 VSSRTC RTC ground J14 nTRST I G8 DD[0] O J15 D[16] I/O G9 D[3] I/O J16 D[17] I/O G10 VSSRTC RTC ground K1 LEDDRV O G11 A[7] O K2 PHDIN I G12 A[8] O K3 VSSIO Pad ground G13 A[9] O K4 DCD I G14 VSSIO Pad ground K5 nTEST[1] I G15 D[12] I/O K6 EINT[3] I G16 D[13] I/O K7 VSSRTC RTC ground Table 63. 256-Ball PBGA Ball Listing (cont.) 114 Table 63. 256-Ball PBGA Ball Listing (cont.) DS453PP2 EP7209 Ball Location Name Type Ball Location Name Type K8 ADCIN I M15 A[20] O K9 COL[4] O M16 D[21] I/O K10 TCLK I N1 nEXTFIQ I K11 D[20] I/O N2 PE[1]/BOOTSEL[1] I K12 D[19] I/O N3 VSSIO Pad ground K13 D[18] I/O N4 VDDIO Pad power K14 VSSIO Pad ground N5 PD[5] I/O K15 VDDIO Pad power N6 PD[2] I/O K16 VDDIO Pad power N7 SSIRXDA I/O L1 RXD[1] I N8 ADCCLK O L2 DSR I N9 SMPCLK O L3 VDDIO Pad power N10 COL[2] O L4 nEINT[1] I N11 D[29] I/O L5 PE[2]/CLKSEL I N12 D[26] I/O L6 VSSRTC RTC ground N13 HALFWORD O L7 PD[0]/LEDFLSH I/O N14 VSSIO Pad ground L8 VSSRTC Core ground N15 D[22] I/O L9 COL[6] O N16 D[23] I/O L10 D[31] I/O P1 VSSRTC RTC ground L11 VSSRTC RTC ground P2 RTCOUT O L12 A[22] O P3 VSSIO Pad ground L13 A[21] O P4 VSSIO Pad ground L14 VSSIO Pad ground P5 VDDIO Pad power L15 A[18] O P6 VSSIO Pad ground L16 A[19] O P7 VSSIO Pad ground M1 nTEST[0] I P8 VDDIO Pad power M2 nEINT[2] I P9 VSSIO Pad ground M3 VDDIO Pad power P10 VDDIO Pad power M4 PE[0]/BOOTSEL[0] I P11 VSSIO Pad ground M5 TMS I P12 VSSIO Pad ground M6 VDDIO Pad power P13 VDDIO Pad power M7 SSITXFR I/O P14 VSSIO Pad ground M8 DRIVE[1] I/O P15 D[24] I/O M9 FB[0] I P16 VDDIO Pad power M10 COL[0] O R1 RTCIN I/O M11 D[27] I/O R2 VDDIO Pad power M12 VSSIO Pad ground R3 PD[4] I/O M13 A[23] O R4 PD[1] I/O M14 VDDIO Pad power R5 SSITXDA O Table 63. 256-Ball PBGA Ball Listing (cont.) Table 63. 256-Ball PBGA Ball Listing (cont.) DS453PP2 115 EP7209 Ball Location Name Type Ball Location R6 R7 nADCCS O T12 BUZ O VDDIO Pad power T13 D[28] I/O R8 ADCOUT O T14 A[26] O R9 COL[7] O T15 D[25] I/O R10 COL[3] O T16 VSSIO Pad ground R11 COL[1] O R12 D[30] I/O R13 A[27] O R14 A[25] O R15 VDDIO Pad power R16 A[24] O T1 VDDRTC RTC power T2 PD[7] I/O T3 PD[6] I/O T4 PD[3] I/O T5 SSICLK I/O T6 SSIRXFR – T7 VDDCORE Core power T8 DRIVE[0] I/O T9 FB[1] I T10 COL[5] O T11 VDDIO Pad power Name Type Table 63. 256-Ball PBGA Ball Listing (cont.) 8.4.1 PBGA Ground Connections Table 64 lists the balls on the PBGA package that must be connected to ground. These extra leads are not used on the PBGA package. A16 E5 E11 E12 J3 J8 J9 N3 N14 F3 F6 F11 F14 K3 K7 K14 P1 P3 P4 P6 P7 P9 P11 P12 P14 C3 C5 C6 C7 C9 C10 C11 C13 C14 G6 G7 G10 G14 L6 L8 L11 L14 T16 D3 D9 D14 H3 H8 H9 H14 M12 Table 64. PBGA Balls to Connect to Ground (VSS) Table 63. 256-Ball PBGA Ball Listing (cont.) 116 DS453PP2 EP7209 9. PACKAGE SPECIFICATIONS 9.1 208-Pin LQFP Package Outline Drawing 29.60 (1.165) 30.40 (1.197) 27.80 (1.094) 28.20 (1.110) 0.17 (0.007) 0.27 (0.011) 27.80 (1.094) 28.20 (1.110) EP7209 29.60 (1.165) 30.40 (1.197) 208-Pin LQFP 0.50 (0.0197) BSC Pin 1 Indicator Pin 208 Pin 1 0.45 (0.018) 0.75 (0.030) 1.35 (0.053) 1.45 (0.057) 1.00 (0.039) BSC 0° MIN 7° MAX 0.09 (0.004) 0.20 (0.008) 1.40 (0.055) 1.60 (0.063) NOTES: 0.05 (0.002) 0.15 (0.006) 1) Dimensions are in millimeters (inches), and controlling dimension is millimeter. 2) Drawing above does not reflect exact package pin count. 3) Before beginning any new design with this device, please contact Cirrus Logic for the latest package information. 4) For pin description, please see 208-Pin LQFP Pin Diagram page 12 DS453PP2 117 EP7209 9.2 EP7209 256-Ball PBGA (17 × 17 × 1.53-mm Body) Dimensions 0.80 (0.032) ±0.05 (.002) 17.00 (0.669) Pin 1 Corner 0.40 (0.016) ±0.10 (.004) +0.70 (.027) 15.00 (0.590) -0.00 30° TYP Pin 1 Indicator 17.00 (0.669) 15.00 (0.590) +0.70 (.027) -0.00 4 Layer 0.56 (0.022) ±0.06 (0.002) 2 Layer 0.36 (0.022) +0.04 (0.001) –0.06 (0.002) TOP VIEW SIDE VIEW 17.00 (0.669) Pin 1 Corner 1.00 (0.040) 1.00 (0.040) REF 16 15 14 13 12 11 109 8 7 6 5 4 3 21 1.00 (0.040) REF A B C D E F G H J K L M N P R T 1.00 (0.040) 0.50 R 3 Places NOTE: 118 17.00 (0.669) BOTTOM VIEW For pin description, please see 256-Ball PBGA Pin Diagram page 112 DS453PP2 EP7209 10. ORDERING INFORMATION The order number for the device is: EP7209 — CV — A Revision † Package Type: V = Low Profile Quad Flat Pack B = Plastic Ball Grid Array (17 mm x 17 mm) Temperature Range: C = Commercial Part Number Product Line: Embedded Processor NOTE: † Contact Cirrus Logic for up-to-date information on revisions. Go to the Cirrus Logic Internet site at http://cirrus.com/corporate/contacts to find contact information for your local sales representative. DS453PP2 119 EP7209 11. APPENDIX A: BOOT CODE ;(C) Copyright 1995-1996, Cirrus Logic, Inc. All Rights Reserved. ; TTL CL-EP7209 Sample program ; version 1.0 (initial version) ;ks ; boot from uart1 AREA |C$$code|,CODE,READONLY ENTRY ; System constants ; HwBaseAddress EQU 0x80000000 HwControl EQU 0x00000100 HwControl2 EQU 0x00001100 HwControlUartEnable EQU 0x00000100 HwStatus EQU 0x00000140 HwStatus2 EQU 0x000001140 HwStatusUartRxFifoEmpty EQU 0x00400000 HwUartData EQU 0x00000480 HwUartData2 EQU 0x00001480 HwUartDataFrameErr EQU 0x0100 HwUartDataParityErr EQU 0x0200 HwUartDataOverrunErr EQU 0x0400 HwUartControl EQU 0x000004C0 HwUartControl2 EQU 0x000014C0 HwUartControlRate EQU 0x00000FFF HwUartControlRate115200 EQU 0x001 HwUartControlRate76800 EQU 0x002 HwUartControlRate57600 EQU 0x003 HwUartControlRate38400 EQU 0x005 ; ; ; ; 120 DS453PP2 EP7209 HwUartControlRate19200 EQU 0x00B HwUartControlRate14400 EQU 0x00F HwUartControlRate9600 EQU 0x017 HwUartControlRate4800 EQU 0x02F HwUartControlRate2400 EQU 0x05F HwUartControlRate1200 EQU 0x0BF HwUartControlRate600 EQU 0x17F HwUartControlRate300 EQU 0x2FF HwUartControlRate150 EQU 0x5FF HwUartControlRate110 EQU 0x82E HwUartControlRate115200_13 EQU 0x000 HwUartControlRate57600_13 EQU 0x001 HwUartControlRate38400_13 EQU 0x002 HwUartControlRate19200_13 EQU 0x005 HwUartControlRate14400_13 EQU 0x007 HwUartControlRate9600_13 EQU 0x00b HwUartControlRate4800_13 EQU 0x017 HwUartControlRate2400_13 EQU 0x02F HwUartControlRate1200_13 EQU 0x060 HwUartControlRate600_13 EQU 0x0c0 HwUartControlRate300_13 EQU 0x182 HwUartControlRate150_13 EQU 0x305 HwUartControlRate110_13 EQU 0x41E HwUartControlBreak EQU 0x00001000 HwUartControlParityEnable EQU 0x00002000 HwUartControlPartiyEvenOrOdd EQU 0x00004000 HwUartControlTwoStopBits EQU 0x00008000 HwUartControlFifoEnable EQU 0x00010000 HwUartControlDataLength EQU 0x00060000 HwUartControlDataLength5 EQU 0x00000000 HwUartControlDataLength6 EQU 0x00020000 HwUartControlDataLength7 EQU 0x00040000 HwUartControlDataLength8 EQU 0x00060000 ; ; 9600baud, 8bits/ch no parity, 1 stop bit UartValue EQU HwUartControlRate9600+HwUartControlDataLength8 UartValue_13 EQU HwUartControlRate9600_13+HwUartControlDataLength8 BufferAddress EQU 0x10000000 ;start address sram snooze buffer codeexeaddr EQU 0x10000000 ; count EQU 0x00000800 ;2k bytes DS453PP2 121 EP7209 startflag EQU ’<’ endflag EQU ’>’ CLKMOD EQU 0x40 ; ;clock mode 1 = 13 MHz ARM Processor constants ArmIrqDisable EQU 0x00000080 ArmFiqDisable EQU 0x00000040 ; 26bit mode is not supported ; ArmUserMode EQU 0x10 ArmFIQMode EQU 0x11 ArmIRQMode EQU 0x12 ArmSVCMode EQU 0x13 ArmAbortMode EQU 0x17 ArmUndefMode EQU 0x1B ArmMaskMode EQU 0x1F CP 0xF CN 0x00 CN 0x01 ; ArmMmuCP ; ArmMmuId ; ArmMmuControl ArmMmuControlMmuEnable EQU 0x00000001 ArmMmuControlAlignFaultEnable EQU 0x00000002 ArmMmuControlCacheEnable EQU 0x00000004 ArmMmuControlWriteBufferEnable EQU 0x00000008 ArmMmuControl32BitCodeEnable EQU 0x00000010 ArmMmuControl32BitDataEnable EQU 0x00000020 ArmMmuControlMandatory EQU 0x00000040 ArmMmuControlBigEndianEnable EQU 0x00000080 ArmMmuControlSystemEnable EQU 0x00000100 ArmMmuControlRomEnable EQU 0x00000200 ; ArmMmuPageTableBase CN 0x02 CN 0x03 CN 0x05 ; ArmMmuDomainAccess ; ArmMmuFlushTlb 122 DS453PP2 EP7209 ; ArmMmuPurgeTlb CN 0x06 CN 0x07 ; ArmMmuFlushIdc ;InitialMmuConfig EQU +ArmMmuControl32BitDataEnable +ArmMmuControlBigEndianEnable ArmMmuControl32BitCodeEnable +ArmMmuControlMandatory InitialMmuConfig EQU ArmMmuControl32BitCodeEnable +ArmMmuControl32BitDataEnable +ArmMmuControlMandatory ;leave as little endian 11/6/96 ks ;============================================================================== ====== ; REAL CODE START ; set little endian, 32bit code, 32bit data by writing to CP15’s control register LDR r0, =InitialMmuConfig MCR ArmMmuCP, 0, r0, ArmMmuControl, c0 ; set the cpu to SVC32 mode MRS r0, CPSR ;read psr BIC r0, r0, #ArmMaskMode ;remove the mode bits ORR r0, r0, #ArmSVCMode ;set to supervisor 32 bit mode MSR CPSR, r0 ; Now set the CPU into the new mode ; ; initialize HW control UARTEnable LDR r12,=HwBaseAddress MOV r0,#HwControlUartEnable STR r0,[r12,#HwControl] LDR r1,=HwStatus2 ADD r1,r1,r12 LDR r2,[r1] TST r2,#CLKMOD LDREQ r0,=UartValue ;load 18 mhz value if bit not set LDRNE r0,=UartValue_13 ;load 13 mhz value if bit set ;Enable UART ;read system flag2 DS453PP2 123 EP7209 STR ; r0,[r12,#HwUartControl] ;initialise Uart Send ready signal LDR r0,=startflag STRB r0,[r12,#HwUartData] ; ; send ready receive the data LDR r3,=count LDR r2,=BufferAddress 01 ; wait for byte available LDR r1,[r12,#HwStatus] TST r1,#HwStatusUartRxFifoEmpty BNE %b01 ; ; spin, if Rx FIFO is empty read the data ,store it and accumulate checksum LDRB r0,[r12,#HwUartData] ; read data STRB r0,[r2],#1 ; save it in memory SUBS r3,r3,#1 ; decrement count BNE %b01 ; do more if count has not expired ; all received, send end flag LDR r0,=endflag STRB r0,[r12,#HwUartData] ; send reply LDR r15,=codeexeaddr ;jump to execution address LTORG END 124 DS453PP2 EP7209 12. INDEX F Symbols functional block diagram 19 functional description 18 / BOOTSEL0 15 / BOOTSEL1 15 / CLKSEL 15 / LEDFLSH 15 /PRDY1 15 Numerics pin information PB 15 PD 15 PE 15 DRIVE 15 FB 15 NTEST 16 A 13 NCS 13 pin information DD 15 NCS 13 D 13 COL 15 PA 15 PD 15 PB 15 PE 15 NEINT 14 RXD 15 TXD 15 PE 15 /PRDY2 PB 15 pin information NCS 13 B boundary scan 47 C clocks 23 external clock input (13 MHz) 24 on-chip PLL 23 CPU core 19 D dedicated LED flasher 47 E endianness 33 I idle state 28 iInternal UARTs 34 in-circuit emulation 48 interrupt Ccontroller 23 L LCD controller 43 M memory and I/O expansion interface 30 CL-EP7211 boot ROM 29 O operating state 28 P PADDR Port A Data Direction Register 54 PADR Port A Data Register 54 PBDR Port B Data Register 54 PBGA ground connections 116 PDDDR Port D Data Direction Register 55 PDDR Port D Data Register 54 PEDDR Port E Data Direction Register 55 pin descriptions, external signal functions 13 pin diagram 12, 108 pin information ADCCLK 15 ADCIN 15 ADCOUT 15 BATOK 14 BUZ 15 CL1 15 CL2 15 CTS 15 DCD 15 DSR 15 EINT3 14 EXPCLK 13 EXPRDY 13 FRM 15 LEDDRV 15 M 15 MOSCIN 16 MOSCOUT 16 NADCCS 15 NBATCHG 14 DS453PP2 125 EP7209 NEXTFIQ 14 NEXTPWR 14 NMEDCHG/ BROM 14 NMOE 13 NMWE 13 NPOR 14 NPWRFL 14 NURESET 14 PHDIN 15 RTCIN 16 RTCOUT 16 RUN/CLKEN 14 SMPCLK 15 SSICLK 14 SSIRXDA 14 SSIRXFR 14 SSITXDA 14 SSITXFR 14 TCLK 16 TDI 16 TDO 16 TMS 16 TNRST 16 WAKEUP 14 WRITE 13 PWM interface 47 S serial interface ADC iInterface 39 clock polarity 43 continuous data transfer 43 discontinuous clock 43 error conditions 43 MCP interface 37 MCP operation 38 readback of residual data 42 support for asymmetric traffic 42 serial interfaces 34 codec sound interface 36 SIR encoder 34 standby state 28 state control 20 SYSFLG, The System Status Flags Register 62 T timer counters 45 free running mode 46 prescale mode 46 U UART 19 R realtime clock 46 resets 23 126 DS453PP2 • Notes •