AD AD9735BBCRL

10-/12-/14-Bit, 1200 MSPS DACS
AD9734/AD9735/AD9736
FEATURES
FUNCTIONAL BLOCK DIAGRAM
RESET
A reduced-specification LVDS interface is utilized to achieve
the high sample rate. The output current can be programmed
over a range of 8.66 mA to 31.66 mA. The AD973x family is
manufactured on a 0.18 μm CMOS process and operates from
1.8 V and 3.3 V supplies for a total power consumption of
380 mW in bypass mode. It is supplied in a 160-lead chip scale
ball grid array for reduced package parasitics.
CLOCK
DISTRIBUTION
S3
2×
BAND GAP
C2
VREF
IOUTA
14-, 12-,
10-BIT DAC
CORE
REFERENCE
CURRENT
C1S1
IOUTB
S2
I120
Figure 1.
PRODUCT HIGHLIGHTS
1.
Low noise and intermodulation distortion (IMD) features
enable high quality synthesis of wideband signals at intermediate frequencies up to 600 MHz.
2.
Double data rate (DDR) LVDS data receivers support the
maximum conversion rate of 1200 MSPS.
3.
Direct pin programmability of basic functions or SPI port
access offers complete control of all AD973x family
functions.
4.
Manufactured on a CMOS process, the AD973x family
uses a proprietary switching technique that enhances
dynamic performance.
5.
The current output(s) of the AD9736 family are easily configured for single-ended or differential circuit topologies.
GENERAL DESCRIPTION
The AD9736, AD9735, and AD9734 are high performance, high
frequency DACs that provide sample rates of up to 1200 MSPS,
permitting multicarrier generation up to their Nyquist
frequency. The AD9736 is the 14-bit member of the family,
while the AD9735 and the AD9734 are the 12-bit and 10-bit
members, respectively. They include a serial peripheral interface
(SPI) port that provides for programming of many internal
parameters and enables readback of status registers.
C3
04862-001
DB[13:0]+
DB[13:0]–
C2
C3
SYNCHRONIZER
DATACLK_IN+
DATACLK_IN–
C1
CONTROLLER
SPI
LVDS
DRIVER
DATACLK_OUT+
DATACLK_OUT–
APPLICATIONS
Broadband communications systems
Cellular infrastructure (digital predistortion)
Point-to-point wireless
CMTS/VOD
Instrumentation, automatic test equipment
Radar, avionics
DACCLK– DACCLK+
IRQ
S1 S2 S3
SDIO
SDO
CSB
SCLK
LVDS
RECEIVER
Pin-compatible family
Excellent dynamic performance
AD9736: SFDR = 82 dBc at fOUT = 30 MHz
AD9736: SFDR = 69 dBc at fOUT = 130 MHz
AD9736: IMD = 87 dBc at fOUT = 30 MHz
AD9736: IMD = 82 dBc at fOUT = 130 MHz
LVDS data interface with on-chip 100 Ω terminations
Built-in self test
LVDS sampling integrity
LVDS-to-DAC data transfer integrity
Low power: 380 mW (IFS = 20 mA; fOUT = 330 MHz)
1.8/3.3 V dual-supply operation
Adjustable analog output
8.66 mA to 31.66 mA (RL = 25 Ω to 50 Ω)
On-chip 1.2 V reference
160-lead chip scale ball grid array (CSP_BGA) package
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD9734/AD9735/AD9736
TABLE OF CONTENTS
Features .............................................................................................. 1
Full Scale Current (FSC) Registers (Reg. 2, Reg. 3)............... 31
Applications....................................................................................... 1
LVDS Controller (LVDS_CNT) Registers
(Reg. 4, Reg. 5, Reg. 6) ............................................................... 31
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 3
Specifications..................................................................................... 4
DC Specifications ......................................................................... 4
Digital Specifications ................................................................... 6
AC Specifications.......................................................................... 8
Absolute Maximum Ratings............................................................ 9
Thermal Resistance ...................................................................... 9
ESD Caution.................................................................................. 9
Pin Configurations and Function Descriptions ......................... 10
Location of Supply and Control Pins....................................... 16
Terminology .................................................................................... 17
Typical Performance Characteristics ........................................... 18
SYNC Controller (SYNC_CNT) Registers
(Reg. 7, Reg. 8)............................................................................ 32
Cross Controller (CROS_CNT) Registers
(Reg. 10, Reg. 11)........................................................................ 32
Analog Control (ANA_CNT) Registers
(Reg. 14, Reg. 15)........................................................................ 33
Built-In Self Test Control (BIST_CNT) Registers
(Reg. 17, Reg. 18, Reg. 19, Reg. 20, Reg. 21)........................... 33
Controller Clock Predivider (CCLK_DIV) Reading
Register (Reg. 22) ....................................................................... 34
Theory of Operation ...................................................................... 35
Serial Peripheral Interface ............................................................. 36
General Operation of the Serial Interface............................... 36
Short Instruction Mode (8-Bit Instruction) ........................... 36
Long Instruction Mode (16-Bit Instruction).......................... 36
Serial Interface Port Pin Descriptions ..................................... 36
SCLK—Serial Clock............................................................... 36
AD9736 Static Linearity, 10 mA Full Scale ............................. 18
CSB—Chip Select................................................................... 37
AD9736 Static Linearity, 20 mA Full Scale ............................. 19
SDIO—Serial Data I/O.......................................................... 37
AD9736 Static Linearity, 30 mA Full Scale ............................. 20
AD9735 Static Linearity, 10 mA, 20 mA, 30 mA
Full Scale...................................................................................... 21
AD9734 Static Linearity, 10 mA, 20 mA, 30 mA
Full Scale...................................................................................... 22
AD9736 Power Consumption, 20 mA Full Scale....................... 23
AD9736 Dynamic Performance, 20 mA Full Scale................ 24
SDO—Serial Data Out .......................................................... 37
MSB/LSB Transfers .................................................................... 37
Notes on Serial Port Operation ................................................ 37
Pin Mode Operation .................................................................. 38
RESET Operation....................................................................... 38
Programming Sequence ............................................................ 38
AD9735, AD9734 Dynamic Performance, 20 mA
Full Scale...................................................................................... 27
Interpolation Filter..................................................................... 39
AD973x WCDMA ACLR, 20 mA Full Scale .......................... 28
Data Interface Controllers......................................................... 39
SPI Register Map............................................................................. 29
LVDS Sample Logic.................................................................... 40
SPI Register Details ........................................................................ 30
LVDS Sample Logic Calibration............................................... 40
Mode Register (Reg. 0) .............................................................. 30
Operating the LVDS Controller in Manual Mode via the
SPI Port ........................................................................................ 41
Interrupt Request Register (IRQ) (Reg. 1) .............................. 30
Rev. A | Page 2 of 72
AD9734/AD9735/AD9736
Operating the LVDS Controller in Surveillance and
Auto Mode ...................................................................................41
SYNC Logic and Controller...........................................................42
SYNC Logic and Controller Operation....................................42
Operation in Manual Mode.......................................................42
Operation in Surveillance and Auto Modes ............................42
FIFO Bypass.................................................................................42
Digital Built-In Self Test (BIST) ....................................................44
Overview ......................................................................................44
AD973x BIST Procedure............................................................45
AD973x Expected BIST Signatures ..........................................45
Generating Expected Signatures ...............................................46
Cross Controller Registers .............................................................47
Analog Control Registers ...............................................................48
Band Gap Temperature Characteristic Trim Bits ...................48
Mirror Roll-Off Frequency Control .........................................48
Headroom Bits.............................................................................48
Voltage Reference........................................................................48
Applications Information...............................................................50
Driving the DACCLK Input ......................................................50
DAC Output Distortion Sources...................................................51
DC-Coupled DAC Output.............................................................52
DAC Data Sources ..........................................................................53
Input Data Timing ..........................................................................54
Synchronization Timing.................................................................55
Power Supply Sequencing ..............................................................56
AD973X Evaluation Board Schematics ........................................57
AD973X Evaluation Board PCB Layout.......................................62
Outline Dimensions........................................................................69
Ordering Guide ...........................................................................69
REVISION HISTORY
9/06—Rev. 0 to Rev. A
Updated Format.................................................................. Universal
Changes to Table 1 ............................................................................5
Changes to Table 2 ............................................................................6
Changes to Table 3 ............................................................................8
Inserted Table 5..................................................................................9
Replaced Pin Configuration and Function Descriptions
Section ..............................................................................................10
Changes to Figure 27 to Figure 38 ................................................21
Changes to Figure 40 ......................................................................23
Changes to Table 9 ..........................................................................29
Changes to Figure 103 ....................................................................56
Changes to Figure 105 ....................................................................58
Changes to Figure 107 ....................................................................60
Changes to Figure 108 ....................................................................61
Changes to Figure 115 ....................................................................68
Updated Outline Dimensions........................................................69
Changes to Ordering Guide...........................................................69
4/05—Revision 0: Initial Version
Rev. A | Page 3 of 72
AD9734/AD9735/AD9736
SPECIFICATIONS
DC SPECIFICATIONS
AVDD33 = DVDD33 = 3.3 V, CVDD18 = DVDD18 = 1.8 V, maximum sample rate, IFS = 20 mA, 1× mode, 25 Ω, 1% balanced load,
unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
Integral Nonlinearity (INL)
Differential Nonlinearity (DNL)
ANALOG OUTPUTS
Offset Error
Gain Error (With Internal
Reference)
Gain Error (Without Internal
Reference)
Full-Scale Output Current
Output Compliance Range
Output Resistance
Output Capacitance
TEMPERATURE DRIFT
Offset
Gain
Reference Voltage 1
REFERENCE
Internal Reference Voltage1
Output Resistance 2
ANALOG SUPPLY VOLTAGES
AVDD33
CVDD18
DIGITAL SUPPLY VOLTAGES
DVDD33
DVDD18
SUPPLY CURRENTS
1× Mode, 1.2 GSPS
IAVDD33
ICVDD18
IDVDD33
IDVDD18
FIR Bypass (1×) Mode
2× Mode, 1.2 GSPS
IAVDD33
ICVDD18
IDVDD33
IDVDD18
FIR 2× Interpolation Filter
Enabled
Min
AD9736
Typ
14
Max
Min
AD9735
Typ
12
Max
Min
AD9734
Typ
10
Max
Unit
Bits
−5.6
−2.1
±1.0
±0.6
+5.6
+2.1
−1.5
−0.5
±0.50
±0.25
+1.5
+0.5
−0.5
−0.1
±0.12
±0.06
+0.5
+0.1
LSB
LSB
−0.01
±0.005
±1.0
+0.01
−0.01
±0.005
±1.0
+0.01
−0.01
±0.005
±1.0
+0.01
% FSR
% FSR
±1.0
8.66
−1.0
20.2
±1.0
31.66
+1.0
8.66
−1.0
20.2
±1.0
31.66
1.0
8.66
−1.0
20.2
% FSR
31.66
+1.0
10
1
10
1
10
1
mA
V
MΩ
pF
0
80
40
0
80
40
0
80
40
ppm/°C
ppm/°C
ppm/°C
1.14
1.2
5
1.26
1.14
1.2
5
1.26
1.14
1.2
5
1.26
V
kΩ
3.13
1.70
3.3
1.8
3.47
1.90
3.13
1.70
3.3
1.8
3.47
1.90
3.13
1.70
3.3
1.8
3.47
1.90
V
V
3.13
1.70
3.3
1.8
3.47
1.90
3.13
1.70
3.3
1.8
3.47
1.90
3.13
1.70
3.3
1.8
3.47
1.90
V
V
25
47
10
122
380
25
47
10
122
380
25
47
10
122
380
mA
mA
mA
mA
mW
25
47
10
234
550
25
47
10
234
550
25
47
10
234
550
mA
mA
mA
mA
mW
Rev. A | Page 4 of 72
AD9734/AD9735/AD9736
Parameter
Static, No Clock
IAVDD33
ICVDD18
IDVDD33
IDVDD18
FIR Bypass (1×) Mode
Sleep Mode, No Clock
IAVDD33
FIR Bypass (1×) Mode
Power-Down Mode 3
IAVDD33
ICVDD18
IDVDD33
IDVDD18
FIR Bypass (1×) Mode
Min
AD9736
Typ
Max
25
8
10
2
133
Min
AD9735
Typ
Max
25
8
10
2
133
Min
AD9734
Typ
Max
25
8
10
2
133
Unit
mA
mA
mA
mA
mW
2.5
59
3.15
65
2.5
59
3.15
65
2.5
59
3.15
65
mA
mW
0.01
0.02
0.01
0.01
0.12
0.13
0.12
0.12
0.11
1.24
0.01
0.02
0.01
0.01
0.12
0.13
0.12
0.12
0.11
1.24
0.01
0.02
0.01
0.01
0.12
0.13
0.12
0.12
0.11
1.24
mA
mA
mA
mA
mW
1
Default band gap adjustment (Reg. 0x0E <2:0> = 0x0).
Use an external amplifier to drive any external load.
3
Typical wake-up time is 8 μs with recommended 1 nF capacitor on VREF pin.
2
Rev. A | Page 5 of 72
AD9734/AD9735/AD9736
DIGITAL SPECIFICATIONS
AVDD33 = DVDD33 = 3.3 V, CVDD18 = DVDD18 = 1.8 V, maximum sample rate, IFS = 20 mA, 1× mode, 25 Ω, 1% balanced load,
unless otherwise noted. LVDS drivers and receivers are compliant to the IEEE-1596 reduced range link, unless otherwise noted.
Table 2.
Parameter
LVDS DATA INPUT
(DB[13:0]+, DB[13:0]−) DB+ = VIA, DB− = VIB
Input Voltage Range, VIA or VIB
Input Differential Threshold, VIDTH
Input Differential Hysteresis, VIDTHH − VIDTHL
Receiver Differential Input Impedance, RIN
LVDS Input Rate
LVDS Minimum Data Valid Period (tMDE)
LVDS CLOCK INPUT
(DATACLK_IN+, DATACLK_IN−) DATACLK_IN+ = VIA, DATACLK_IN− = VIB
Input Voltage Range, VIA or VIB
Input Differential Threshold, 1 VIDTH
Input Differential Hysteresis, VIDTHH − VIDTHL
Receiver Differential Input Impedance, RIN
Maximum Clock Rate
LVDS CLOCK OUTPUT
(DATACLK_OUT+, DATACLK_ OUT−) DATACLK_OUT+ = Voa, DATACLK_OUT− = Vob 100 Ω Termination
Output Voltage High, VOA or VOB
Output Voltage Low, VOA or VOB
Output Differential Voltage, |VOD|
Output Offset Voltage, VOS
Output Impedance, Single-Ended, RO
RO Mismatch Between A and B, ΔRO
Change in |VOD| Between 0 and 1, |ΔVOD|
Change in VOS Between 0 and 1, ΔVOS
Output Current—Driver Shorted to Ground, ISA, ISB
Output Current—Drivers Shorted Together, ISAB
Power-Off Output Leakage, |IXA|, |IXB|
Maximum Clock Rate
DAC CLOCK INPUT (CLK+, CLK−)
Input Voltage Range, CLK− or CLK+
Differential Peak-to-Peak Voltage
Common-Mode Voltage
Maximum Clock Rate
SERIAL PERIPHERAL INTERFACE
Maximum Clock Rate (fSCLK, 1/tSCLK)
Minimum Pulse Width High, tPWH
Minimum Pulse Width Low, tPWL
Minimum SDIO and CSB to SCLK Setup, tDS
Minimum SCLK to SDIO Hold, tDH
Maximum SCLK to Valid SDIO and SDO, tDV
Minimum SCLK to Invalid SDIO and SDO, tDNV
Rev. A | Page 6 of 72
Min
Typ
825
−100
Max
Unit
1575
+100
mV
mV
mV
Ω
MSPS
ps
20
80
1200
120
344
825
−100
1575
+100
20
80
600
120
1375
1025
150
1150
80
200
100
250
1250
120
10
25
25
20
4
10
600
0
400
300
1200
800
400
800
1600
500
20
20
20
10
5
20
5
mV
mV
mV
Ω
MHz
mV
mV
mV
mV
Ω
%
mV
mV
mA
mA
mA
MHz
mV
mV
MHz
MHz
ns
ns
ns
ns
ns
ns
AD9734/AD9735/AD9736
Parameter
INPUT (SDI, SDIO, SCLK, CSB)
Voltage in High, VIH
Voltage in Low, VIL
Current in High, IIH
Current in Low, IIL
SDIO OUTPUT
Voltage out High, VOH
Voltage out Low, VOL
Current out High, IOH
Current out Low, IOL
Min
Max
Unit
−10
−10
0.8
+10
+10
V
V
μA
μA
2.4
0
3.6
0.4
2.0
Typ
3.3
0
4
4
1
Refer to the Input Data Timing section for recommended LVDS differential drive levels.
Rev. A | Page 7 of 72
V
V
mA
mA
AD9734/AD9735/AD9736
AC SPECIFICATIONS
AVDD33 = DVDD33 = 3.3 V, CVDD18 = DVDD18 = 1.8 V, maximum sample rate, IFS = 20 mA, 1× mode, 25 Ω, 1% balanced load,
unless otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
Maximum Update Rate
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fDAC = 800 MSPS
fOUT = 20 MHz
fDAC = 1200 MSPS
fOUT = 50 MHz
fOUT = 100 MHz
fOUT = 316 MHz
fOUT = 550 MHz
TWO-TONE INTERMODULATION
DISTORTION (IMD)
fDAC = 1200 MSPS
fOUT2 = fOUT + 1.25 MHz
fOUT = 40 MHz
fOUT = 50 MHz
fOUT = 100 MHz
fOUT = 316 MHz
fOUT = 550 MHz
NOISE SPECTRAL DENSITY (NSD)
Single Tone
fDAC = 1200 MSPS
fOUT = 50 MHz
fOUT = 100 MHz
fOUT = 241MHz
fOUT = 316 MHz
fOUT = 550 MHz
Eight-Tone
fDAC = 1200 MSPS, 500 kHz Tone Spacing
fOUT = 50 MHz
fOUT = 100 MHz
fOUT = 241MHz
fOUT = 316 MHz
fOUT = 550 MHz
Min
AD9736
Typ
1200
Max
Min
AD9735
Typ
Max
1200
Min
AD9734
Typ
Max
1200
Unit
MSPS
75
75
75
dBc
80
77
63
55
76
74
63
54
76
71
60
53
dBc
dBc
dBc
dBc
88
85
84
70.5
65
84
84
81
67
60
83
83
79
66
60
dBc
dBc
dBc
dBc
dBc
−158.5
−165
−164
−160.5
−158
−155
−162
−161
−159.5
−157
−155
−154
−154
−155
−152
−149
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
−163.3
−166.5
−166
−165
−164
−162
−163
−163
−161.5
−162
−160
−154
−152
−150.5
−151
−150
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
dBm/Hz
Rev. A | Page 8 of 72
AD9734/AD9735/AD9736
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
AVDD33
DVDD33
DVDD18
CVDD18
AVSS
AVSS
DVSS
CLK+, CLK−
PIN_MODE
DATACLK_IN,
DATACLK_OUT
LVDS Data Inputs
IOUTA, IOUTB
I120, VREF, IPTAT
IRQ, CSB, SCLK, SDO,
SDIO, RESET
Junction Temperature
Storage Temperature
With
Respect to
AVSS
DVSS
DVSS
CVSS
DVSS
CVSS
CVSS
CVSS
DVSS
DVSS
Min
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
−0.3 V
Max
+3.6 V
+3.6 V
+1.98 V
+1.98 V
+0.3 V
+0.3 V
+0.3 V
CVDD18 + 0.18 V
DVDD33 + 0.3 V
DVDD33 + 0.3 V
DVSS
AVSS
AVSS
DVSS
−0.3 V
−1.0 V
−0.3 V
−0.3 V
DVDD33 + 0.3 V
AVDD33 + 0.3 V
AVDD33 + 0.3 V
DVDD33 + 0.3 V
−65°C
150°C
+150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to
absolute maximum ratings for extended periods may effect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 5. Thermal Resistance
Package Type
160-Lead Ball, CSP_BGA
θJA 1
31.2
Unit
°C/W
1
θJA measurement in still air.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Note that this device in its current form does not meet Analog Devices’ standard requirements for ESD as measured against the charged
device model (CDM). As such, special care should be used when handling this product, especially in a manufacturing environment. Analog
Devices will provide a more ESD-hardy product in the near future at which time this warning will be removed from this data sheet.
Rev. A | Page 9 of 72
AD9734/AD9735/AD9736
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A
B
C
D
DACCLK– E
DACCLK+ F
G
H
J
K
DB13 (MSB)
L
DB12
DB0 (LSB) M
DB11
N
04862-005
DB9
DB10
DB8
DB7
DB6
DATACLK_IN
DB5
DATACLK_OUT
DB4
DB3
DB2
DB1
P
Figure 2. AD9736 Digital LVDS Input, Clock I/O (Top View)
Table 6. AD9736 Pin Function Descriptions
Pin No.
A1, A2, A3, B1, B2, B3, C1, C2, C3, D2, D3
A4, A5, A6, A9, A10, A11, B4, B5, B6, B9,
B10, B11, C4, C5, C6, C9, C10, C11, D4, D5,
D6, D9, D10, D11
A7, B7, C7, D7
A8, B8, C8, D8
A12, A13, B12, B13, C12, C13, D12, D13
A14
B14
Mnemonic
CVDD18
AVSS
Description
1.8 V Clock Supply.
Analog Supply Ground.
IOUTB
IOUTA
AVDD33
DNC
I120
C14
VREF
D1, E2, E3, E4, F2, F3, F4, G1, G2, G3, G4
D14
CVSS
IPTAT
E1, F1
E11, E12, F11, F12, G11, G12
E13
DACCLK−/DACCLK+
AVSS
IRQ/UNSIGNED
E14
RESET/PD
F13
CSB/2×
F14
G13
G14
H1, H2, H3, H4, H11, H12, H13, H14, J1, J2,
J3, J4, J11, J12, J13, J14
SDIO/FIFO
SCLK/FSC0
SDO/FSC1
DVDD18
DAC Negative Output. 10 mA to 30 mA full-scale output current.
DAC Positive Output. 10 mA to 30 mA full-scale output current.
3.3 V Analog Supply.
Do Not Connect.
Nominal 1.2 V Reference. Tie to analog ground via 10 kΩ resistor to
generate a 120 μA reference current.
Band Gap Voltage Reference I/O. Tie to analog ground via 1 nF
capacitor; output impedance is approximately 5 kΩ.
Clock Supply Ground.
Factory Test Pin. Output current, proportional to absolute
temperature, is approximately 10 μA at 25°C with a slope of
approximately 20 nA/°C.
Negative/Positive DAC Clock Input (DACCLK).
Analog Supply Ground Shield. Tie to AVSS at the DAC.
If PIN_MODE = 0, IRQ: Active low open-drain interrupt request
output, pull up to DVDD33 with 10 kΩ resistor.
If PIN_MODE = 1, UNSIGNED: Digital input pin where 0 = twos
complement input data format, 1 = unsigned.
If PIN_MODE = 0, RESET: 1 resets the AD9736.
If PIN_MODE = 1, PD: 1 puts the AD9736 in the power-down state.
See the Serial Peripheral Interface section and the Pin Mode
Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
1.8 V Digital Supply.
Rev. A | Page 10 of 72
AD9734/AD9735/AD9736
Pin No.
K1, K2, K3, K4, K11, K12, L2, L3, L4, L5, L6,
L9, L10, L11, L12, M3, M4, M5, M6, M9,
M10, M11, M12
K13, K14
Mnemonic
DVSS
Description
Digital Supply Ground.
DB<13>−/DB<13>+
L1
PIN_MODE
L7, L8, M7, M8, N7, N8, P7, P8
L13, L14
DVDD33
DB<12>−/DB<12>+
M2, M1
DB<0>−/DB<0>+
M13, M14
DB<11>−/DB<11>+
N1, P1
DB<1>−/DB<1>+
N2, P2
DB<2>−/DB<2>+
N3, P3
DB<3>−/DB<3>+
N4, P4
DB<4>−/DB<4>+
N5, P5
DB<5>−/DB<5>+
N6, P6
N10, P10
DATACLK_OUT−/
DATACLK_OUT+
DATACLK_IN−/
DATACLK_IN+
DB<6>−/DB<6>+
Negative/Positive Data Input Bit 13 (MSB). Conforms to IEEE-1596
reduced range link.
0 = SPI Mode. SPI is enabled.
1 = PIN Mode. SPI is disabled; direct pin control.
3.3 V Digital Supply.
Negative/Positive Data Input Bit 12. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 0 (LSB). Conforms to IEEE-1596
reduced range link.
Negative/Positive Data Input Bit 11. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 1. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 2. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 3. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 4. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 5. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Output Clock. Conforms to IEEE-1596
reduced range link.
N11, P11
DB<7>−/DB<7>+
N12, P12
DB<8>−/DB<8>+
N13, P13
DB<9>−/DB<9>+
N14, P14
DB<10>−/DB<10>+
N9, P9
Negative/Positive Data Input Clock. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 6. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 7. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 8. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 9. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 10. Conforms to IEEE-1596 reduced
range link.
Rev. A | Page 11 of 72
AD9734/AD9735/AD9736
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A
B
C
D
DACCLK– E
DACCLK+ F
G
H
J
K
DB11 (MSB)
L
DB10
DB9
NC M
N
04862-115
DB8
DB7
DB6
DB5
DB4
DATACLK_IN
DB3
DATACLK_OUT
DB2
DB1
NC
DB0 (LSB)
P
Figure 3. AD9735 Digital LVDS Input, Clock I/O (Top View)
Table 7. AD9735 Pin Function Descriptions
Pin No.
A1, A2, A3, B1, B2, B3, C1, C2, C3, D2, D3
A4, A5, A6, A9, A10, A11, B4, B5, B6, B9,
B10, B11, C4, C5, C6, C9, C10, C11, D4, D5,
D6, D9, D10, D11
A7, B7, C7, D7
A8, B8, C8, D8
A12, A13, B12, B13, C12, C13, D12, D13
A14
B14
Mnemonic
CVDD18
AVSS
Description
1.8 V Clock Supply.
Analog Supply Ground.
IOUTB
IOUTA
AVDD33
DNC
I120
C14
VREF
D1, E2, E3, E4, F2, F3, F4, G1, G2, G3, G4
D14
CVSS
IPTAT
E1, F1
E11, E12, F11, F12, G11, G12
E13
DACCLK−/DACCLK+
AVSS
IRQ/UNSIGNED
E14
RESET/PD
F13
CSB/2×
F14
G13
G14
H1, H2, H3, H4, H11, H12, H13, H14, J1, J2,
J3, J4, J11, J12, J13, J14
K1, K2, K3, K4, K11, K12, L2, L3, L4, L5, L6,
L9, L10, L11, L12, M3, M4, M5, M6, M9,
M10, M11, M12
SDIO/FIFO
SCLK/FSC0
SDO/FSC1
DVDD18
DAC Negative Output. 10 mA to 30 mA full-scale output current.
DAC Positive Output. 10 mA to 30 mA full-scale output current.
3.3 V Analog Supply.
Do Not Connect.
Nominal 1.2 V Reference. Tie to analog ground via 10 kΩ resistor to
generate a 120 μA reference current.
Band Gap Voltage Reference I/O. Tie to analog ground via 1 nF
capacitor; output impedance approximately 5 kΩ.
Clock Supply Ground.
Factory Test Pin; Output current, proportional to absolute
temperature, is approximately 10 μA at 25°C with a slope of
approximately 20 nA/°C.
Negative/Positive DAC Clock Input (DACCLK).
Analog Supply Ground Shield. Tie to AVSS at the DAC.
If PIN_MODE = 0, IRQ: Active low open-drain interrupt request
output, pull up to DVDD33 with 10 kΩ resistor.
If PIN_MODE = 1, UNSIGNED: Digital input pin where 0 = twos
complement input data format, 1 = unsigned.
If PIN_MODE = 0, RESET: 1 resets the AD9735.
If PIN_MODE = 1, PD: 1 puts the AD9735 in the power-down state.
See the Serial Peripheral Interface section and the Pin Mode
Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
1.8 V Digital Supply.
DVSS
Digital Supply Ground.
Rev. A | Page 12 of 72
AD9734/AD9735/AD9736
Pin No.
K13, K14
Mnemonic
DB<11>−/DB<11>+
L1
PIN_MODE
L7, L8, M7, M8, N7, N8, P7, P8
L13, L14
DVDD33
DB<10>−/DB<10>+
M1, M2
M13, M14
NC
DB<9>−/DB<9>+
N1, P1
N2, P2
NC
DB<0>−/DB<0>+
N3, P3
DB<1>−/DB<1>+
N4, P4
DB<2>−/DB<2>+
N5, P5
DB<3>−/DB<3>+
N6, P6
N10, P10
DATACLK_OUT−/
DATACLK_OUT+
DATACLK_IN−/
DATACLK_IN+
DB<4>−/DB<4>+
N11, P11
DB<5>−/DB<5>+
N12, P12
DB<6>−/DB<6>+
N13, P13
DB<7>−/DB<7>+
N14, P14
DB<8>−/DB<8>+
N9, P9
Description
Negative/Positive Data Input Bit 11 (MSB). Conforms to IEEE-1596
reduced range link.
0 = SPI Mode. SPI is enabled.
1 = PIN Mode. SPI disabled; direct pin control.
3.3 V Digital Supply.
Negative/Positive Data Input Bit 10. Conforms to IEEE-1596 reduced
range link.
No Connect.
Negative/Positive Data Input Bit 9. Conforms to IEEE-1596 reduced
range link.
No Connect.
Negative/Positive Data Input Bit 0 (LSB). Conforms to IEEE-1596
reduced range link.
Negative/Positive Data Input Bit 1. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 2. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 3. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Output Clock. Conforms to IEEE-1596
reduced range link.
Negative/Positive Data Input Clock. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 4. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 5. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 6. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 7. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 8. Conforms to IEEE-1596 reduced
range link.
Rev. A | Page 13 of 72
AD9734/AD9735/AD9736
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A
B
C
D
DACCLK– E
DACCLK+ F
G
H
J
K
DB9 (MSB)
L
DB8
NC M
DB7
N
04862-114
DB6
DB5
DB4
DB3
DB2
DATACLK_IN
DB1
DATACLK_OUT
NC
DB0 (LSB)
NC
NC
P
Figure 4. AD9734 Digital LVDS Input, Clock I/O (Top View)
Table 8. AD9734 Pin Function Descriptions
Pin No.
A1, A2, A3, B1, B2, B3, C1, C2, C3, D2, D3
A4, A5, A6, A9, A10, A11, B4, B5, B6, B9,
B10, B11, C4, C5, C6, C9, C10, C11, D4, D5,
D6, D9, D10, D11
A7, B7, C7, D7
A8, B8, C8, D8
A12, A13, B12, B13, C12, C13, D12, D13
A14
B14
Mnemonic
CVDD18
AVSS
Description
1.8 V Clock Supply.
Analog Supply Ground.
IOUTB
IOUTA
AVDD33
DNC
I120
C14
VREF
D1, E2, E3, E4, F2, F3, F4, G1, G2, G3, G4
D14
CVSS
IPTAT
E1, F1
E11, E12, F11, F12, G11, G12
E13
DACCLK−/DACCLK+
AVSS
IRQ/UNSIGNED
E14
RESET/PD
F13
CSB/2×
F14
G13
G14
H1, H2, H3, H4, H11, H12, H13, H14, J1, J2,
J3, J4, J11, J12, J13, J14
K1, K2, K3, K4, K11, K12, L2, L3, L4, L5, L6,
L9, L10, L11, L12, M3, M4, M5, M6, M9,
M10, M11, M12
SDIO/FIFO
SCLK/FSC0
SDO/FSC1
DVDD18
DAC Negative Output. 10 mA to 30 mA full-scale output current.
DAC Positive Output. 10 mA to 30 mA full-scale output current.
3.3 V Analog Supply.
Do Not Connect.
Nominal 1.2 V Reference. Tie to analog ground via 10 kΩ resistor to
generate a 120 μA reference current.
Band Gap Voltage Reference I/O. Tie to analog ground via 1 nF
capacitor; output impedance approximately 5 kΩ.
Clock Supply Ground.
Factory Test Pin. Output current, proportional to absolute
temperature, is approximately 10 μA at 25°C with a slope of
approximately 20 nA/°C.
Negative/Positive DAC Clock Input (DACCLK).
Analog Supply Ground Shield. Tie to AVSS at the DAC.
If PIN_MODE = 0, IRQ: Active low open-drain interrupt request
output, pull up to DVDD33 with 10 kΩ resistor.
If PIN_MODE = 1, UNSIGNED: Digital input pin where 0 = twos
complement input data format, 1 = unsigned.
If PIN_MODE = 0, RESET: 1 resets the AD9734.
If PIN_MODE = 1, PD: 1 puts the AD9734 in the power-down state.
See the Serial Peripheral Interface section and the Pin Mode
Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
See the Pin Mode Operation section for pin description.
1.8 V Digital Supply.
DVSS
Digital Supply Ground.
Rev. A | Page 14 of 72
AD9734/AD9735/AD9736
Pin No.
K13, K14
Mnemonic
DB<9>−/DB<9>+
L1
PIN_MODE
L7, L8, M7, M8, N7, N8, P7, P8
L13, L14
DVDD33
DB<8>−/DB<8>+
M1, M2
M13, M14
NC
DB<7>−/DB<7>+
N1, P1
N2, P2
N3, P3
N4, P4
NC
NC
NC
DB<0>−/DB<0>+
N5, P5
DB<1>−/DB<1>+
N6, P6
N10, P10
DATACLK_OUT−/
DATACLK_OUT+
DATACLK_IN−/
DATACLK_IN+
DB<2>−/DB<2>+
N11, P11
DB<3>−/DB<3>+
N12, P12
DB<4>−/DB<4>+
N13, P13
DB<5>−/DB<5>+
N14, P14
DB<6>−/DB<6>+
N9, P9
Description
Negative/Positive Data Input Bit 9 (MSB). Conforms to IEEE-1596
reduced range link.
0 = SPI Mode. SPI is enabled.
1 = PIN Mode. SPI is disabled; direct pin control.
3.3 V Digital Supply.
Negative/Positive Data Input Bit 8. Conforms to IEEE-1596 reduced
range link.
No Connect.
Negative/Positive Data Input Bit 7. Conforms to IEEE-1596 reduced
range link.
No Connect.
No Connect.
No Connect.
Negative/Positive Data Input Bit 0 (LSB). Conforms to IEEE-1596
reduced range link.
Negative/Positive Data Input Bit 1. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Output Clock. Conforms to IEEE-1596
reduced range link.
Negative/Positive Data Input Clock. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 2. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 3. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 4. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 5. Conforms to IEEE-1596 reduced
range link.
Negative/Positive Data Input Bit 6. Conforms to IEEE-1596 reduced
range link.
Rev. A | Page 15 of 72
AD9734/AD9735/AD9736
LOCATION OF SUPPLY AND CONTROL PINS
5
6
7
8
9 10 11 12 13 14
1
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
J
J
K
K
L
L
M
M
N
N
P
P
AVDD33, 3.3V, ANALOG SUPPLY
AVSS, ANALOG SUPPLY GROUND SHIELD
2
3
4
5
6
7
8
4
5
6
7
8
9 10 11 12 13 14
DVDD33, 3.3V DIGITAL SUPPLY
DVSS DIGITAL SUPPLY GROUND
Figure 7. Digital Supply Pins (Top View)
Figure 5. Analog Supply Pins (Top View)
1
3
DVDD18, 1.8V DIGITAL SUPPLY
04862-002
AVSS, ANALOG SUPPLY GROUND
2
9 10 11 12 13 14
A
B
1
C
2
3
4
5
6
7
8
9 10 11 12 13 14
D
A
E
B
I120
F
C
VREF
G
D
IPTAT
H
E
J
IRQ
F
K
CSB
SDIO
G
L
SCLK
SDO
H
J
N
K
P
PIN_MODE L
CVDD18, 1.8V CLOCK SUPPLY
CVSS, CLOCK SUPPLY GROUND
04862-003
M
M
2×
FIFO
N
FSC0
FSC1
Figure 8. Analog I/O and SPI Control Pins (Top View)
Rev. A | Page 16 of 72
RESET
PIN_MODE = 1,
SPI DISABLED
PD
UNSIGNED
P
Figure 6. Clock Supply Pins (Top View)
PIN_MODE = 0,
SPI ENABLED
04862-006
4
04862-004
3
IOUTA
2
IOUTB
1
AD9734/AD9735/AD9736
TERMINOLOGY
Linearity Error (Integral Nonlinearity or INL)
The maximum deviation of the actual analog output from the
ideal output, determined by a straight line drawn from zero to
full scale.
Power Supply Rejection
The maximum change in the full-scale output as the supplies
are varied from nominal to minimum and maximum specified
voltages.
Differential Nonlinearity (DNL)
The measure of the variation in analog value, normalized to full
scale, associated with a 1 LSB change in digital input code.
Settling Time
The time required for the output to reach and remain within a
specified error band about its final value, measured from the
start of the output transition.
Monotonicity
A DAC is monotonic if the output either increases or remains
constant as the digital input increases.
Offset Error
The deviation of the output current from the ideal of zero. For
IOUTA, 0 mA output is expected when the inputs are all 0s. For
IOUTB, 0 mA output is expected when all inputs are set to 1s.
Gain Error
The difference between the actual and ideal output span. The
actual span is determined by the output when all inputs are set
to 1s minus the output when all inputs are set to 0s.
Output Compliance Range
The range of allowable voltage at the output of a current output
DAC. Operation beyond the maximum compliance limits can
cause either output stage saturation or breakdown, resulting in
nonlinear performance.
Temperature Drift
Specified as the maximum change from the ambient (25°C)
value to the value at either TMIN or TMAX. For offset and gain
drift, the drift is reported in ppm of full-scale range (FSR) per
°C. For reference drift, the drift is reported in ppm per °C.
Glitch Impulse
Asymmetrical switching times in a DAC give rise to undesired
output transients that are quantified by a glitch impulse. It is
specified as the net area of the glitch in pV-s.
Spurious-Free Dynamic Range
The difference, in dB, between the rms amplitude of the output
signal and the peak spurious signal over the specified bandwidth.
Total Harmonic Distortion (THD)
The ratio of the rms sum of the first six harmonic components
to the rms value of the measured input signal. It is expressed as
a percentage or in decibels (dB).
Multitone Power Ratio
The spurious-free dynamic range containing multiple carrier
tones of equal amplitude. It is measured as the difference
between the rms amplitude of a carrier tone to the peak
spurious signal in the region of a removed tone.
Rev. A | Page 17 of 72
AD9734/AD9735/AD9736
TYPICAL PERFORMANCE CHARACTERISTICS
AD9736 STATIC LINEARITY, 10 mA FULL SCALE
1.00
1.0
0.75
0.8
0.50
0.6
0.25
0.4
ERROR (LSB)
ERROR (LSB)
0
–0.25
–0.50
–0.75
–1.00
0.2
0
–0.2
–0.4
–1.25
–0.6
–1.50
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–1.0
04862-008
–2.00
0
Figure 9. AD9736 INL, −40°C, 10 mA FS
2048
4096
6144
8192 10240 12288 14336 16384
CODE
04862-010
–0.8
–1.75
Figure 12. AD9736 DNL, −40°C, 10 mA FS
1.00
1.0
0.75
0.8
0.50
0.6
0.25
0.4
ERROR (LSB)
ERROR (LSB)
0
–0.25
–0.50
–0.75
–1.00
0.2
0
–0.2
–0.4
–1.25
–0.6
–1.50
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–1.0
04862-008
–2.00
0
Figure 10. AD9736 INL, 25°C, 10 mA FS
2048
4096
6144
8192 10240 12288 14336 16384
CODE
04862-011
–0.8
–1.75
Figure 13. AD9736 DNL, 25°C, 10 mA FS
1.00
1.0
0.75
0.8
0.50
0.6
0.25
0.4
ERROR (LSB)
–0.25
–0.50
–0.75
–1.00
0.2
0
–0.2
–0.4
–1.25
–0.6
–1.50
–2.00
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
Figure 11. AD9736 INL, 85°C, 10 mA FS
–1.0
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
Figure 14. AD9736 DNL, 85°C, 10 mA FS
Rev. A | Page 18 of 72
04862-012
–0.8
–1.75
04862-009
ERROR (LSB)
0
AD9734/AD9735/AD9736
0.6
0.8
0.5
0.6
0.4
0.4
0.3
0.2
0.2
0
–0.2
–0.4
–0.6
0.1
0
–0.1
–0.2
–0.8
–0.3
–1.0
–0.4
–1.2
–0.5
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–0.6
0
0.6
0.8
0.5
0.6
0.4
0.4
0.3
0.2
0.2
ERROR (LSB)
1.0
0
–0.2
–0.4
–0.6
0
–0.2
–0.3
–0.4
–1.2
–0.5
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–0.6
0
0.6
0.8
0.5
0.6
0.4
0.4
0.3
0.2
0.2
ERROR (LSB)
1.0
0
–0.2
–0.4
–0.6
–0.2
–0.4
–1.2
–0.5
6144
8192 10240 12288 14336 16384
CODE
8192 10240 12288 14336 16384
CODE
0
–0.3
4096
6144
–0.1
–1.0
2048
4096
0.1
–0.8
0
2048
Figure 19. AD9736 DNL, 25°C, 20 mA FS
04862-015
ERROR (LSB)
Figure 16. AD9736 INL, 25°C, 20 mA FS
–1.4
8192 10240 12288 14336 16384
CODE
–0.1
–1.0
0
6144
0.1
–0.8
–1.4
4096
Figure 18. AD9736 DNL, −40°C, 20 mA FS
04862-014
ERROR (LSB)
Figure 15. AD9736 INL, −40°C, 20 mA FS
2048
04862-017
0
Figure 17. AD9736 INL, 85°C, 20 mA FS
–0.6
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
Figure 20. AD9736 DNL, 85°C, 20 mA FS
Rev. A | Page 19 of 72
04862-018
–1.4
04862-016
ERROR (LSB)
1.0
04862-013
ERROR (LSB)
AD9736 STATIC LINEARITY, 20 mA FULL SCALE
AD9734/AD9735/AD9736
AD9736 STATIC LINEARITY, 30 mA FULL SCALE
2.0
0.6
0.5
1.5
0.4
0.3
0.2
0.5
ERROR (LSB)
0
–0.5
–1.0
0
–0.1
–0.2
–0.3
–0.4
–1.5
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–0.6
0
Figure 21. AD9736 INL, −40°C, 30 mA FS
6144
8192 10240 12288 14336 16384
CODE
0.6
0.5
1.5
0.4
1.0
0.3
0.2
0.5
ERROR (LSB)
ERROR (LSB)
4096
Figure 24. AD9736 DNL, −40°C, 30 mA FS
2.0
0
–0.5
–1.0
0.1
0
–0.1
–0.2
–0.3
–0.4
–1.5
–0.5
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
–0.6
04862-020
–2.0
2048
04862-022
–0.5
04862-019
–2.0
0.1
0
Figure 22. AD9736 INL, 25°C, 30 mA FS
2048
4096
6144
8192 10240 12288 14336 16384
CODE
04862-023
ERROR (LSB)
1.0
Figure 25. AD9736 DNL, 25°C, 30 mA FS
2.0
1.0
1.5
0.5
1.0
0.5
0
0
ERROR (LSB)
0
0
–0.5
–0.5
–1.0
–0.5
–1.0
–1.5
–2.0
–1.0
–1.5
–2.5
–2.0
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
Figure 23. AD9736 INL, 85°C, 30 mA FS
–3.0
0
2048
4096
6144
8192 10240 12288 14336 16384
CODE
Figure 26. AD9736 DNL, 85°C, 30 mA FS
Rev. A | Page 20 of 72
04862-024
–1.5
04862-021
ERROR (LSB)
0
AD9734/AD9735/AD9736
AD9735 STATIC LINEARITY, 10 mA, 20 mA, 30 mA FULL SCALE
0.4
0.100
0.050
0.3
0
ERROR (LSB)
ERROR (LSB)
0.2
0.1
–0.050
–0.100
0
–0.150
–0.1
512
1024
1536
2048
2560
3072
3584
4096
CODE
–0.250
0
512
1024
1536
2048
2560
3072
3584
4096
3584
4096
3584
4096
CODE
Figure 27. AD9735 INL, 25°C, 10 mA FS
04862-028
0
04862-025
–0.2
–0.200
Figure 30. AD9735 DNL, 25°C, 10 mA FS
0.15
0.100
0.075
0.10
0.050
0.05
ERROR (LSB)
ERROR (LSB)
0.025
0
–0.05
0
–0.025
–0.050
–0.10
–0.075
–0.15
512
1024
1536
2048
2560
3072
3584
4096
CODE
–0.125
0
1536
2048
2560
3072
Figure 31. AD9735 DNL, 25°C, 20 mA FS
0.2
0.050
0.1
0
–0.050
0
–1.000
ERROR (LSB)
–0.1
–0.2
–0.3
–1.150
–0.200
–0.250
–0.4
–0.300
–0.5
0
512
1024
1536
2048
CODE
2560
3072
3584
4096
Figure 29. AD9735 INL, 25°C, 30 mA FS
–0.400
0
512
1024
1536
2048
CODE
2560
3072
Figure 32. AD9735 DNL, 25°C, 30 mA FS
Rev. A | Page 21 of 72
04862-030
–0.350
04862-027
ERROR (LSB)
1024
CODE
Figure 28. AD9735 INL, 25°C, 20 mA FS
–0.6
512
04862-029
0
04862-026
–0.20
–0.100
AD9734/AD9735/AD9736
AD9734 STATIC LINEARITY, 10 mA, 20 mA, 30 mA FULL SCALE
0.04
0.03
0.02
0.02
ERROR (LSB)
0.04
0
0.01
0
–0.04
–0.01
–0.06
0
128
256
384
512
640
768
896
1024
CODE
04862-031
–0.02
–0.02
0
128
256
384
512
640
768
896
1024
CODE
04862-034
ERROR (LSB)
0.06
Figure 36. AD9734 DNL, 25°C, 10 mA FS
Figure 33. AD9734 INL, 25°C, 10 mA FS
0.03
0.03
0.02
0.02
0.01
0.01
ERROR (LSB)
–0.01
–0.02
0
–0.01
–0.03
–0.04
–0.02
0
128
256
384
512
CODE
640
768
896
1024
–0.03
04862-032
–0.06
0
128
256
384
512
640
768
896
1024
896
1024
CODE
04862-035
–0.05
Figure 37. AD9734 DNL, 25°C, 20 mA FS
Figure 34. AD9734 INL, 25°C, 20 mA FS
0.01
0.06
0.04
0
0.02
–0.01
ERROR (LSB)
0
–0.02
–0.04
–0.06
–0.02
–0.03
–0.04
–0.08
–0.12
0
128
256
384
512
640
768
CODE
896
1024
–0.06
0
128
256
384
512
640
768
CODE
Figure 38. AD9734 DNL, 25°C, 30 mA FS
Figure 35. AD9734 INL, 25°C, 30 mA FS
Rev. A | Page 22 of 72
04862-036
–0.05
–0.10
04862-033
ERROR (LSB)
ERROR (LSB)
0
AD9734/AD9735/AD9736
AD9736 POWER CONSUMPTION, 20 mA FULL SCALE
0.50
0.7
0.45
0.6
TOTAL
0.40
TOTAL
0.5
0.25
0.20
DVDD18
0.15
DVDD18
0.3
CVDD18
0.2
AVDD33
0.10
DVDD33
0
250
500
750
fDAC (MHz)
1000
1250
1500
0
DVDD33
AVDD33
0.1
CVDD18
0.05
0
0.4
0
250
500
750
1000
1250
1500
fDAC (MHz)
Figure 40. AD9736, 2× Interpolation Mode Power vs. fDAC at 25°C
Figure 39. AD9736 1× Mode Power vs. fDAC at 25°C
Rev. A | Page 23 of 72
04862-038
POWER (W)
0.30
04862-037
POWER (W)
0.35
AD9734/AD9735/AD9736
80
75
800MSPS
IMD (dBc)
SFDR (dBc)
70
65
60
1.2GSPS
1GSPS
50
0
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
04862-039
55
92
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
0
50
100
150
200
Figure 41. AD9736 SFDR vs. fOUT over fDAC at 25°C
300
350
400
450
500
550
Figure 44. AD9736 IMD vs. fOUT over 50 Parts, 25°C,1.2 GSPS
80
90
85
75
1GSPS
80
70
75
IMD (dBc)
SFDR (dBc)
250
fOUT (MHz)
04862-042
AD9736 DYNAMIC PERFORMANCE, 20 mA FULL SCALE
65
+85°C
60
70
800MSPS
65
1.2GSPS
–40°C
60
+25°C
55
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
50
0
100
200
300
400
500
600
fOUT (MHz)
Figure 42. AD9736 SFDR vs. fOUT over Temperature
04862-043
0
04862-040
50
55
Figure 45. AD9736 IMD vs. fOUT over fDAC at 25°C
90
78
76
85
74
80
72
75
IMD (dBc)
68
66
64
62
–40°C
70
+25°C
+85°C
65
60
60
58
56
52
0
50
100
150
200
250
300 350
fOUT (MHz)
400
450
500
550
50
0
100
200
300
400
500
600
fOUT (MHz)
Figure 43. AD9736 SFDR vs. fOUT over 50 Parts, 25°C, 1.2 GSPS
Figure 46. AD9736 IMD vs. fOUT over Temperature, 1.2 GSPS
Rev. A | Page 24 of 72
04862-044
55
54
04862-041
SFDR (dBc)
70
AD9734/AD9735/AD9736
95
90
90
85
IMD
0dBFS
80
75
IMD (dBc)
SFDR
75
70
–6dBFS
65
65
60
60
55
0
10
fOUT (MHz)
100
50
0
300
400
500
600
Figure 50. AD9736 IMD vs. fOUT over AOUT, 25°C, 1.2 GSPS
90
90
THIRD-ORDER IMD
85
85
SFDR
80
SFDR, IMD (dBc)
75
70
65
75
70
SFDR_1×
65
60
60
55
55
0
50
100
150
200
fOUT (MHz)
SFDR_2×
80
250
300
350
50
04862-046
SFDR, IMID (dBc)
200
fOUT (MHz)
Figure 47. AD9736 Low Frequency IMD and SFDR vs. fOUT, 25°C, 1.2 GSPS
50
100
Figure 48. AD9736 IMD and SFDR vs. fOUT, 25°C, 1.2 GSPS, 2× Interpolation
0
50
100
150
200
250
300
350
fOUT (MHz)
04862-049
55
–12dBFS
70
04862-048
80
04862-045
IMD AND SFDR (dBc)
85
Figure 51. AD9736 SFDR vs. fOUT, 25°C, 1.2 GSPS, 1× and 2× Interpolation
80
90
75
85
THIRD-ORDER IMD_1×
70
80
–12dBFS
55
–6dBFS
70
65
50
60
45
55
40
0
100
200
300
fOUT (MHz)
400
500
600
Figure 49. AD9736 SFDR vs. fOUT over AOUT, 25°C, 1.2 GSPS
50
04862-047
SFDR (dBc)
0dBFS
60
75
0
50
100
150
200
fOUT (MHz)
250
300
350
04862-050
SFDR, IMD (dBc)
THIRD-ORDER IMD_2×
65
Figure 52. AD9736 IMD vs. fOUT, 25°C, 1.2 GSPS, 1× and 2× Interpolation
Rev. A | Page 25 of 72
AD9734/AD9735/AD9736
–150
–150
–152
–152
–154
–154
–156
1.2GSPS
–160
–162
–160
–164
–166
–166
–168
–168
0
100
200
300
fOUT (MHz)
400
500
600
–170
–40°C
+25°C
0
100
200
300
400
500
600
fOUT (MHz)
Figure 56. AD9736 8-Tone NSD vs. fOUT over Temperature, 1.2 GSPS
Figure 53. AD9736 1-Tone NSD vs. fOUT over fDAC, 25°C
–150
–157
–152
–158
–154
–159
–156
NSD (dBm/Hz)
+85°C
–158
–40°C
–160
+25°C
–162
–164
–160
–161
–162
–163
–164
–166
–165
–168
100
200
300
fOUT (MHz)
400
500
600
0
50
100
150
200
250
300
350
400
450
500
550
fOUT (MHz)
Figure 54. AD9736 1-Tone NSD vs. fOUT over Temperature, 1.2 GSPS
04862-055
–166
0
04862-052
–170
+85°C
–162
–164
–170
NSD (dBm/Hz)
–158
04862-054
–158
NSD (dBm/Hz)
1GSPS
04862-051
NSD (dBm/Hz)
–156
Figure 57. AD9736 1-Tone NSD vs. fOUT over 50 Parts, 1.2 GSPS, 25°C
–150
–161
–152
–154
–162
NSD (dBm/Hz)
–158
–160
–162
1GSPS
–163
–164
–165
–164
1.2GSPS
–166
–166
–170
0
100
200
300
fOUT (MHz)
400
500
600
Figure 55. AD9736 8-Tone NSD vs. fOUT over fDAC, 25°C
–167
0
50
100
150
200
250
300
fOUT (MHz)
350
400
450
500
550
04862-056
–168
04862-053
NSD (dBm/Hz)
–156
Figure 58. AD9736 8-Tone NSD vs. fOUT over 50 Parts, 1.2 GSPS, 25°C
Rev. A | Page 26 of 72
AD9734/AD9735/AD9736
AD9735, AD9734 DYNAMIC PERFORMANCE, 20 mA FULL SCALE
80
90
85
75
1GSPS
80
800MSPS
75
IMD (dBc)
SFDR (dBc)
70
65
60
800MSPS
70
1.2GSPS
65
1GSPS
60
0
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
50
04862-060
50
55
1.2GSPS
0
Figure 59. AD9735 SFDR vs. fOUT over fDAC, 1.2 GSPS
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
04862-063
55
Figure 62. AD9734 IMD vs. fOUT over fDAC, 1.2 GSPS
80
–150
–152
75
–154
–156
NSD (dBc/Hz)
800MSPS
65
1GSPS
60
–160
–162
8 TONES
–166
1.2GSPS
0
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
–168
–170
0
50
Figure 60. AD9734 SFDR vs. fOUT over fDAC, 1.2 GSPS
Figure 63. AD9735 NSD vs. fOUT, 1.2 GSPS
90
–145
1GSPS
–147
85
–149
80
800MSPS
8 TONES
–151
NSD (dBc/Hz)
75
70
65
1.2GSPS
–153
1 TONE
–155
–157
–159
60
–161
55
0
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
–165
0
50
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
Figure 64. AD9734 NSD vs. fOUT, 1.2 GSPS
Figure 61. AD9735 IMD vs. fOUT over fDAC, 1.2 GSPS
Rev. A | Page 27 of 72
04862-065
50
–163
04862-062
IMD (dBc)
100 150 200 250 300 350 400 450 500 550 600
fOUT (MHz)
04862-064
55
50
1 TONE
–158
–164
04862-061
SFDR (dBc)
70
AD9734/AD9735/AD9736
AD973x WCDMA ACLR, 20 mA FULL SCALE
REF –22.75dBm
#AVG
LOG 10dB/
04862-057
#ATTEN 6dB
PAVG
10
W1
S2
CENTER 134.83MHz
#RES BW 30kHz
RMS RESULTS
CARRIER POWER
–10.72dBm/
3.84000MHz
VBW 300kHz
OFFSET FREQ
5.00MHz
10.0MHz
15.0MHz
REF BW
3.840MHz
3.840MHz
3.884MHz
LOWER
dBc
dBm
–81.65
–92.37
–82.06
–92.78
–82.11
–92.83
SPAN 33.88MHz
SWEEP 109.9ms (601pts)
UPPER
dBc
–81.39
–82.43
–82.39
dBm
–92.11
–93.16
–93.11
Figure 65. AD9736 WCDMA Carrier at 134.83 MHz, fDAC = 491.52 MSPS
REF –22.75dBm
#AVG
LOG 10dB/
04862-058
#ATTEN 6dB
PAVG
10 S2
CENTER 134.83MHz
#RES BW 30kHz
RMS RESULTS
CARRIER POWER
–10.72dBm/
3.84000MHz
VBW 300kHz
OFFSET FREQ
5.00MHz
10.0MHz
15.0MHz
REF BW
3.840MHz
3.840MHz
3.884MHz
LOWER
dBc
dBm
–80.32
–91.10
–81.13
–91.91
–80.43
–91.21
SPAN 33.88MHz
SWEEP 109.9ms (601pts)
UPPER
dBc
–80.60
–80.75
–81.36
dBm
–91.38
–91.53
–92.13
Figure 66. AD9735 WCDMA Carrier at 134.83 MHz, fDAC = 491.52 MSPS
REF –22.75dBm
#AVG
LOG 10dB/
04862-059
#ATTEN 6dB
PAVG
10 S2
CENTER 134.83MHz
#RES BW 30kHz
RMS RESULTS
CARRIER POWER
–10.76dBm/
3.84000MHz
VBW 300kHz
OFFSET FREQ
5.00MHz
10.0MHz
15.0MHz
SPAN 33.88MHz
SWEEP 109.9ms (601pts)
REF BW
3.840MHz
3.840MHz
3.884MHz
LOWER
dBc
dBm
–71.07
–81.83
–70.55
–81.31
–70.79
–81.56
UPPER
dBc
–71.23
–71.42
–71.25
dBm
–81.99
–82.19
–82.01
Figure 67. AD9734 WCDMA Carrier at 134.83 MHz, fDAC = 491.52 MSPS
Rev. A | Page 28 of 72
AD9734/AD9735/AD9736
SPI REGISTER MAP
Write 0 to unspecified or reserved bit locations. Reading these bits returns unknown values.
Table 9. SPI Register Map
Reg. Addr.
Dec.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Hex.
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default
(Hex)
Pin Mode
(Hex)
MODE
IRQ
FSC_1
FSC_2
LVDS_CNT1
LVDS_CNT2
LVDS_CNT3
SYNC_CNT1
SYNC_CNT2
RESERVED
CROS_CNT1
CROS_CNT2
RESERVED
RESERVED
ANA_CNT1
ANA_CNT2
RESERVED
BIST_CNT
BIST<7:0>
BIST<15:8>
BIST<23:16>
BIST<31:24>
CCLK_DIV
SDIO_DIR
LVDS
SLEEP
FSC<7>
MSD<3>
SD<3>
LSURV
FIFOSTAT3
SSURV
LSBFIRST
SYNC
RESET
CROSS
LONG_INS
RESERVED
2X MODE
IE_LVDS
FIFO MODE
IE_SYNC
FSC<6>
MSD<2>
SD<2>
LAUTO
FIFOSTAT2
SAUTO
FSC<5>
MSD<1>
SD<1>
LFLT<3>
FIFOSTAT1
SFLT<3>
FSC<4>
MSD<0>
SD<0>
LFLT<2>
FIFOSTAT0
SFLT<2>
FSC<3>
MHD<3>
LCHANGE
LFLT<1>
VALID
SFLT<1>
FSC<2>
MHD<2>
ERR_HI
LFLT<0>
SCHANGE
SFLT<0>
DATAFRMT
IE_CROSS
FSC<9>
FSC<1>
MHD<1>
ERR_LO
LTRH<1>
PHOF<1>
RESERVED
PD
RESERVED
FSC<8>
FSC<0>
MHD<0>
CHECK
LTRH<0>
PHOF<0>
STRH<0>
00
00
02
00
00
00
00
00
00
00
00
02
00
00
00
00
00
00
UPDEL<5>
DNDEL<5>
UPDEL<4>
DNDEL<4>
UPDEL<3>
DNDEL<3>
UPDEL<2>
DNDEL<2>
UPDEL<1>
DNDEL<1>
UPDEL<0>
DNDEL<0>
00
00
00
00
HDRM<4>
HDRM<3>
TRMBG<2>
HDRM<2>
TRMBG<1>
HDRM<1>
TRMBG<0>
HDRM<0>
C0
CA
C0
CA
LVDS_EN
SYNC_EN
CLEAR
00
00
CCD<2>
CCD<1>
CCD<0>
00
00
MSEL<1>
HDRM<7>
MSEL<0>
HDRM<6>
HDRM<5>
SEL<1>
SEL<0>
SIG_READ
RESERVED
RESERVED
RESERVED
RESERVED
CCD<3>
Rev. A | Page 29 of 72
AD9734/AD9735/AD9736
SPI REGISTER DETAILS
Reading these registers returns previously written values for all defined register bits, unless otherwise noted. Reset value for write registers
in bold text.
MODE REGISTER (REG. 0)
ADDR
0x00
Name
MODE
Bit 7
SDIO_DIR
Bit 6
LSB/MSB
Bit 5
RESET
Bit 4
LONG_INS
Bit 3
2× MODE
Bit 2
FIFO MODE
Bit 1
DATAFRMT
Bit 0
PD
Table 10. Mode Register Bit Descriptions
Bit Name
SDIO_DIR
Read/Write
WRITE
LSB/MSB
WRITE
RESET
WRITE
LONG_INS
WRITE
2×_MODE
WRITE
FIFO_MODE
WRITE
DATAFRMT
WRITE
PD
WRITE
Description
0, input only per SPI standard.
1, bidirectional per SPI standard.
0, MSB first per SPI standard.
1, LSB first per SPI standard.
NOTE: Only change LSB/MSB order in single-byte instructions to avoid erratic behavior due to bit
order errors.
0, execute software reset of SPI and controllers, reload default register values except Registers 0x00
and 0x04.
1, set software reset, write 0 on the next (or any following) cycle to release the reset.
0, short (single-byte) instruction word.
1, long (two-byte) instruction word, not necessary since the maximum internal address is REG31
(0x1F).
0, disable 2× interpolation filter.
1, enable 2× interpolation filter.
0, disable FIFO synchronization.
1, enable FIFO synchronization.
0, signed input DATA with midscale = 0x0000.
1, unsigned input DATA with midscale = 0x2000.
0, enable LVDS Receiver, DAC, and clock circuitry.
1, power down LVDS Receiver, DAC, and clock circuitry.
INTERRUPT REQUEST REGISTER (IRQ) (REG. 1)
ADDR
0x01
Name
IRQ
Bit 7
LVDS
Bit 6
SYNC
Bit 5
CROSS
Bit 4
RESERVED
Bit 3
IE_LVDS
Bit 2
IE_SYNC
Table 11. Interrupt Register Bit Descriptions
Bit Name
LVDS
Read/Write
WRITE
READ
SYNC
WRITE
READ
CROSS
WRITE
READ
IE_LVDS
WRITE
IE_SYNC
WRITE
IE_CROSS
WRITE
Description
Don’t care.
0, no active LVDS receiver interrupt.
1, interrupt in LVDS receiver occurred.
Don’t care.
0, no active SYNC logic interrupt.
1, interrupt in SYNC logic occurred.
Don’t care.
0, no active CROSS logic interrupt.
1, interrupt in CROSS logic occurred.
0, reset LVDS receiver interrupt and disable future LVDS receiver interrupts.
1, enable LVDS receiver interrupt to activate IRQ pin.
0, reset SYNC logic interrupt and disable future SYNC logic interrupts.
1, enable SYNC logic interrupt to activate IRQ pin.
0, reset CROSS logic interrupt and disable future CROSS logic interrupts.
1, enable CROSS logic interrupt to activate IRQ pin.
Rev. A | Page 30 of 72
Bit 1
IE_CROSS
Bit 0
RESERVED
AD9734/AD9735/AD9736
FULL SCALE CURRENT (FSC) REGISTERS (REG. 2, REG. 3)
ADDR
0x02
0x03
Name
FSC_1
FSC_2
Bit 7
SLEEP
FSC<7>
Bit 6
–
FSC<6>
Bit 5
Bit 4
Bit 3
Bit 2
–
FSC<5>
–
FSC<4>
–
FSC<3>
–
FSC<2>
Bit 1
FSC<9>
FSC<1>
Bit 0
FSC<8>
FSC<0>
Bit 1
MHD<1>
ERR_LO
LTRH<1>
Bit 0
MHD<0>
CHECK
LTRH<0>
Table 12. Full Scale Current Output Register Bit Descriptions
Bit Name
SLEEP
Read/Write
WRITE
FSC<9:0>
WRITE
Description
0, enable DAC output.
1, set DAC output current to 0 mA.
0x000, 10 mA full-scale output current.
0x200, 20 mA full-scale output current.
0x3FF, 30 mA full-scale output current.
LVDS CONTROLLER (LVDS_CNT) REGISTERS (REG. 4, REG. 5, REG. 6)
ADDR
0x04
0x05
0x06
Name
LVDS_CNT1
LVDS_CNT2
LVDS_CNT3
Bit 7
MSD<3>
SD<3>
LSURV
Bit 6
MSD<2>
SD<2>
LAUTO
Bit 5
MSD<1>
SD<1>
LFLT<3>
Bit 4
MSD<0>
SD<0>
LFLT<2>
Bit 3
MHD<3>
LCHANGE
LFLT<1>
Bit 2
MHD<2>
ERR_HI
LFLT<0>
Table 13. LVDS Controller Register Bit Descriptions
Bit Name
MSD<3:0>
Read/Write
WRITE
READ
MHD<3:0>
WRITE
READ
SD<3:0>
WRITE
READ
LCHANGE
READ
ERR_HI
ERR_LO
CHECK
READ
READ
READ
LSURV
WRITE
LAUTO
WRITE
LFLT<3:0>
WRITE
LTRH<2:0>
WRITE
Description
0x0, set setup delay for the measurement system.
If ( LAUTO = 1), the latest measured value for the setup delay.
If ( LAUTO = 0), readback of the last SPI write to this bit.
0x0, set hold delay for the measurement system.
If ( LAUTO = 1), the latest measured value for the hold delay.
If ( LAUTO = 0), readback of the last SPI write to this bit.
0x0, set sample delay.
If ( LAUTO = 1), the result of a measurement cycle is stored in this register.
If ( LAUTO = 0), readback of the last SPI write to this bit.
0, no change from previous measurement.
1, change in value from the previous measurement.
NOTE: The average filter and the threshold detection are not applied to this bit.
One of the 15 LVDS inputs is above the input voltage limits of the IEEE reduced link specification.
One of the 15 LVDS inputs is below the input voltage limits of the IEEE reduced link specification.
0, phase measurement—sampling in the previous or following DATA cycle.
1, phase measurement—sampling in the correct DATA cycle.
0, the controller stops after completion of the current measurement cycle.
1, continuous measurements are taken and an interrupt is issued if the clock alignment drifts beyond the
threshold value.
0, sample delay is not automatically updated.
1, continuously starts measurement cycles and updates the sample delay according to the measurement.
NOTE: LSURV (Reg. 6, Bit 7) must be set to 1 and the LVDS IRQ (Reg. 1, Bit 3) must be set to 0 for AUTO mode.
0x0, average filter length, Delay = Delay + Delta Delay/2^ LFLT <3:0>, values greater than 12 (0x0C) are
clipped to 12.
000, set auto update threshold values.
Rev. A | Page 31 of 72
AD9734/AD9735/AD9736
SYNC CONTROLLER (SYNC_CNT) REGISTERS (REG. 7, REG. 8)
ADDR
0x07
0x08
Name
SYNC_CNT1
SYNC_CNT2
Bit 7
FIFOSTAT3
SSURV
Bit 6
FIFOSTAT2
SAUTO
Bit 5
FIFOSTAT1
SFLT<3>
Bit 4
FIFOSTAT0
SFLT<2>
Bit 3
VALID
SFLT<1>
Bit 2
SCHANGE
SFLT<0>
Bit 1
PHOF<1>
RESERVED
Bit 0
PHOF<0>
STRH<0>
Table 14. Sync Controller Register Bit Descriptions
Bit Name
FIFOSTAT<2:0>
FIFOSTAT<3>
Read/Write
READ
READ
VALID
READ
SCHANGE
READ
PHOF<1:0>
WRITE
READ
SSURV
WRITE
SAUTO
WRITE
SFLT<3:0>
WRITE
STRH<0>
WRITE
Description
Position of FIFO read counter ranges from 0 to 7.
0, SYNC logic OK.
1, error in SYNC logic.
0, FIFOSTAT<3:0> is not valid yet.
1, FIFOSTAT<3:0> is valid after a reset.
0, no change in FIFOSTAT<3:0>.
1, FIFOSTAT<3:0> has changed since the previous measurement cycle when SSURV = 1 (surveillance mode
active).
00, change the readout counter.
Current setting of the readout counter (PHOF<1:0>) in surveillance mode (SSURV = 1) after an interrupt.
Current calculated optimal readout counter value in AUTO mode (SAUTO = 1).
0, the controller stops after completion of the current measurement cycle.
1, continuous measurements are taken and an interrupt is issued if the readout counter drifts beyond the
threshold value.
0, readout counter (PHOF<3:0>) is not automatically updated.
1, continuously starts measurement cycles and updates the readout counter according to the
measurement.
NOTE: SSURV (Reg. 8, Bit 7) must be set to 1 and the SYNC IRQ (Reg. 1, Bit 2) must be set to 0 for AUTO
mode.
0x0, average filter length, FIFOSTAT = FIFOSTAT + Delta FIFOSTAT/2 ^ SFLT<3:0>; values greater than 12
(0x0C) are clipped to 12.
0, if FIFOSTAT<2:0> = 0 or 7, a sync interrupt is generated.
1, if FIFOSTAT<2:0> = 0, 1, 6 or 7, a sync interrupt is generated.
CROSS CONTROLLER (CROS_CNT) REGISTERS (REG. 10, REG. 11)
ADDR
0x0A
0x0B
Name
CROS_CNT1
CROS_CNT2
Bit 7
–
–
Bit 6
–
–
Bit 5
UPDEL<5>
DNDEL<5>
Bit 4
UPDEL<4>
DNDEL<4>
Bit 3
UPDEL<3>
DNDEL<3>
Bit 2
UPDEL<2>
DNDEL<2>
Bit 1
UPDEL<1>
DNDEL<1>
Table 15. Cross Controller Register Description
Bit Name
UPDEL<5:0>
DNDEL<5:0>
Read/Write
WRITE
WRITE
Description
0x00, move the differential output stage switching point up, set to 0 if DNDEL is non-zero.
0x00, move the differential output stage switching point down, set to 0 if UPDEL is non-zero.
Rev. A | Page 32 of 72
Bit 0
UPDEL<0>
DNDEL<0>
AD9734/AD9735/AD9736
ANALOG CONTROL (ANA_CNT) REGISTERS (REG. 14, REG. 15)
ADDR
0x0E
0x0F
Name
ANA_CNT1
ANA_CNT2
Bit 7
MSEL<1>
HDRM<7>
Bit 6
MSEL<0>
HDRM<6>
Bit 5
–
HDRM<5>
Bit 4
–
HDRM<4>
Bit 3
–
HDRM<3>
Bit 2
TRMBG<2>
HDRM<2>
Bit 1
TRMBG<1>
HDRM<1>
Bit 0
TRMBG<0>
HDRM<0>
Table 16. Analog Control Register Bit Descriptions
Bit Name
MSEL<1:0>
Read/Write
WRITE
Description
TRMBG<2:0>
WRITE
000, band gap temperature characteristic trim.
NOTE: See the plot in the Analog Control Registers section.
HDRM<7:0>
WRITE
0xCA, output stack headroom control.
HDRM<7:4> set reference offset from AVDD33 (VCAS centering).
HDRM<3:0> set overdrive (current density) trim (temperature tracking).
Note: Set to 0xCA for optimum performance.
00, mirror roll off frequency control = bypass.
01, mirror roll off frequency control = narrowest bandwidth.
10, mirror roll off frequency control = medium bandwidth.
11, mirror roll off frequency control = widest bandwidth.
NOTE: See the plot in the Analog Control Registers section.
BUILT-IN SELF TEST CONTROL (BIST_CNT) REGISTERS (REG. 17, REG. 18, REG. 19, REG. 20, REG. 21)
ADDR
0x11
0x12
0x13
0x14
0x15
Name
BIST_CNT
BIST<7:0>
BIST<15:8>
BIST<23:16>
BIST<31:24>
Bit 7
SEL<1>
BIST<7>
BIST<15>
BIST<23>
BIST<31>
Bit 6
SEL<0>
BIST<6>
BIST<14>
BIST<22>
BIST<30>
Bit 5
SIG_READ
BIST<5>
BIST<13>
BIST<21>
BIST<29>
Bit 4
–
BIST<4>
BIST<12>
BIST<20>
BIST<28>
Bit 3
–
BIST<3>
BIST<11>
BIST<19>
BIST<27>
Bit 2
LVDS_EN
BIST<2>
BIST<10>
BIST<18>
BIST<26>
Table 17. BIST Control Register Bit Descriptions
Bit Name
SEL<1:0>
Read/Write
WRITE
SIG_READ
WRITE
LVDS_EN
WRITE
SYNC_EN
WRITE
CLEAR
WRITE
BIST<31:0>
READ
Description
00, write result of the LVDS Phase 1 BIST to BIST<31:0>.
01, write result of the LVDS Phase 2 BIST to BIST<31:0>.
10, write result of the SYNC Phase 1 BIST to BIST<31:0>.
11, write result of the SYNC Phase 2 BIST to BIST<31:0>.
0, no action.
1, enable BIST signature readback.
0, no action.
1, enable LVDS BIST.
0, no action.
1, enable SYNC BIST.
0, no action.
1, clear all BIST registers.
Results of the built-in self test.
Rev. A | Page 33 of 72
Bit 1
SYNC_EN
BIST<1>
BIST<9>
BIST<17>
BIST<25>
Bit 0
CLEAR
BIST<0>
BIST<8>
BIST<16>
BIST<24>
AD9734/AD9735/AD9736
CONTROLLER CLOCK PREDIVIDER (CCLK_DIV) READING REGISTER (REG. 22)
ADR
0x16
Name
CCLK_DIV
Bit 7
RESERVED
Bit 6
RESERVED
Bit 5
RESERVED
Bit 4
RESERVED
Bit 3
CCD<3>
Bit 2
CCD<2>
Bit 1
CCD<1>
Bit 0
CCD<0>
Table 18. Controller Clock Predivider Register Bit Descriptions
Bit Name
CCD<3:0>
Read/Write
WRITE
Description
0x0, controller clock = DACCLK/16.
0x1, controller clock = DACCLK/32.
0x2, controller clock = DACCLK/64 …
0xF, controller clock = DACCLK/524288.
NOTE: The 100 MHz to 1.2 GHz DACCLK must be divided to less than 10 MHz for correct operation. CCD<3:0>
must be programmed to divide the DACCLK so that this relationship is not violated. Controller clock =
DACCLK/(2 ^ ( CCD<3:0> + 4 )).
Rev. A | Page 34 of 72
AD9734/AD9735/AD9736
THEORY OF OPERATION
The AD9736, AD9735, and AD9734 are 14-bit, 12-bit, and
10-bit DACs that run at an update rate up to 1.2 GSPS. Input
data can be accepted up to the full 1.2 GSPS rate, or a 2×
interpolation filter can be enabled (2× mode) allowing full
speed operation with a 600 MSPS input data rate. The DATA
and DATACLK_IN inputs are parallel LVDS, meeting the IEEE
reduced swing LVDS specifications with the exception of input
hysteresis. The DATACLK_IN input runs at one-half the input
DATA rate in a double data rate (DDR) format. Each edge of
DATACLK_IN transfers DATA into the AD9736, as shown in
Figure 79.
The DACCLK−/DACCLK+ inputs (Pin E1 and Pin F1) directly
drive the DAC core to minimize clock jitter. The DACCLK
signal is also divided by 2 (1× and 2× mode), then output as the
DATACLK_OUT. The DATACLK_OUT signal clocks the data
source. The DAC expects DDR LVDS data (DB<13:0>) aligned
with the DDR input clock (DATACLK_IN) from a circuit similar to the one shown in Figure 96. Table 19 shows the clock
relationships.
Table 19. AD973x Clock Relationship
MODE
1×
2×
DACCLK
1.2 GHz
1.2 GHz
DATACLK_OUT
600 MHz
600 MHz
DATACLK_IN
600 MHz
300 MHz
DATA
1.2 GSPS
600 MSPS
Maintaining correct alignment of data and clock is a common
challenge with high speed DACs, complicated by changes in
temperature and other operating conditions. Using the
DATACLK_OUT signal to generate the data allows most of the
internal process, temperature, and voltage delay variation to be
cancelled. The AD973x further simplifies this high speed data
capture problem with two adaptive closed-loop timing
controllers.
One timing controller manages the LVDS data and data clock
alignment (LVDS controller), and the other manages the LVDS
data and DACCLK alignment (sync controller).
The LVDS controller locates the data transitions and delays the
DATACLK_IN so that its transition is in the center of the valid
data window. The sync controller manages the FIFO that moves
data from the LVDS DATACLK_IN domain to the DACCLK
domain.
Both controllers can operate in manual mode under external
processor control, in surveillance mode where error conditions
generate external interrupts, or in automatic mode where errors
are automatically corrected.
The LVDS and sync controllers include moving average filtering
for noise immunity and variable thresholds to control activity.
Normally, the controllers are set to run in automatic mode,
making any necessary adjustments without dropping or duplicating samples sent to the DAC. Both controllers require initial
calibration prior to entering automatic update mode.
The AD973x analog output changes 35 DACCLK cycles after
the input data changes in 1× mode with the FIFO disabled. The
FIFO adds up to eight additional cycles of delay. This delay is
read from the SPI port. Internal clock delay variation is less
than a single DACCLK cycle at 1.2 GHz (833 ps).
Stopping the AD973x DATACLK_IN while the DACCLK is still
running can lead to unpredictable output signals. This occurs
because the internal digital signal path is interleaved. The last
two samples clocked into the DAC continue to be clocked out
by DACCLK even after DATACLK_IN has stopped. The resulting output signal is at a frequency of one-half fDAC, and the
amplitude depends on the difference between the last two
samples.
Control of the AD973x functions is via the serially programmed
registers listed in Table 9. Optionally, a limited number of functions can be directly set by external pins in pin mode.
Rev. A | Page 35 of 72
AD9734/AD9735/AD9736
SERIAL PERIPHERAL INTERFACE
The AD973x serial port is a flexible, synchronous serial
communications port, allowing easy interface to many
industry-standard microcontrollers and microprocessors. The
serial I/O is compatible with most synchronous transfer
formats, including both the Motorola SPI® and Intel® SSR
protocols. The interface allows read/write access to all registers
that configure the AD973x. Single- or multiple-byte transfers
are supported, as well as most significant bit first (MSB-first) or
least significant bit first (LSB-first) transfer formats. The
AD973x serial interface port can be configured as a single pin
I/O (SDIO) or two unidirectional pins for in/out (SDIO/SDO).
SDO (PIN G14)
SCLK (PIN G13)
SPI PORT
CSB (PIN F13)
The short instruction byte is shown in the following table:
MSB
I7
R/W
I6
N1
I5
N0
I4
A4
I3
A3
I2
A2
I1
A1
LSB
I0
A0
R/W, Bit 7 of the instruction byte, determines whether a read or
a write data transfer occurs after the instruction byte write.
Logic high indicates read operation. Logic 0 indicates a write
operation. N1, N0, Bit 6, and Bit 5 of the instruction byte
determine the number of bytes to be transferred during the data
transfer cycle. The bit decodes are shown in Table 20.
A4, A3, A2, A1, A0, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0 of the
instruction byte, determine which register is accessed during
the data transfer portion of the communications cycle. For
multibyte transfers, this address is the starting byte address. The
remaining register addresses are generated by the AD973x,
based on the LSBFIRST bit (Reg. 0, Bit 6).
AD973x
04862-066
SDIO (PIN F14)
SHORT INSTRUCTION MODE (8-BIT INSTRUCTION)
Figure 68. AD973x SPI Port
The AD973x can optionally be configured via external pins
rather than the serial interface. When the PIN_MODE input
(Pin L1) is high, the serial interface is disabled and its pins are
reassigned for direct control of the DAC. Specific functionality
is described in the Pin Mode Operation section.
GENERAL OPERATION OF THE SERIAL INTERFACE
There are two phases to a communication cycle with the
AD973x. Phase 1 is the instruction cycle, which is the writing of
an instruction byte into the AD973x, coincident with the first
eight SCLK rising edges. The instruction byte provides the
AD973x serial port controller with information regarding the
data transfer cycle, which is Phase 2 of the communication
cycle. The Phase 1 instruction byte defines whether the
upcoming data transfer is read or write, the number of bytes in
the data transfer, and the starting register address for the first
byte of the data transfer. The first eight SCLK rising edges of
each communication cycle are used to write the instruction byte
into the AD973x.
The remaining SCLK edges are for Phase 2 of the communication cycle. Phase 2 is the actual data transfer between the
AD973x and the system controller. Phase 2 of the communication cycle is a transfer of 1, 2, 3, or 4 data bytes as determined
by the instruction byte. Using one multibyte transfer is the
preferred method. Single-byte data transfers are useful to
reduce CPU overhead when register access requires one byte
only. Registers change immediately upon writing to the last bit
of each transfer byte.
CSB (Chip Select) can be raised after each sequence of 8 bits
(except the last byte) to stall the bus. The serial transfer resumes
when CSB is lowered. Stalling on nonbyte boundaries resets
the SPI.
Table 20. Byte Transfer Count
N1
0
0
1
1
N2
0
1
0
1
Description
Transfer 1 byte
Transfer 2 bytes
Transfer 3 bytes
Transfer 4 bytes
LONG INSTRUCTION MODE (16-BIT INSTRUCTION)
The long instruction bytes are shown in the following table:
MSB
I15
R/W
I7
A7
I14
N1
I6
A6
I13
N0
I5
A5
I12
A12
I4
A4
I11
A11
I3
A3
I10
A10
I2
A2
I9
A9
I1
A1
LSB
I8
A8
I0
A0
If LONG_INS = 1 (Reg. 0, Bit 4), the instruction byte is
extended to 2 bytes where the second byte provides an
additional 8 bits of address information. Address 0x00 to
Address 0x1F are equivalent in short and long instruction
modes. The AD973x does not use any addresses greater than 31
(0x1F), so always set LONG_INS = 0.
SERIAL INTERFACE PORT PIN DESCRIPTIONS
SCLK—Serial Clock
The serial clock pin is used to synchronize data to and from the
AD973x and to run the internal state machines. The maximum
frequency of SCLK is 20 MHz. All data input to the AD973x is
registered on the rising edge of SCLK. All data is driven out of
the AD973x on the rising edge of SCLK.
Rev. A | Page 36 of 72
AD9734/AD9735/AD9736
CSB—Chip Select
Active low input starts and gates a communication cycle. It
allows more than one device to be used on the same serial
communications lines. The SDO and SDIO pins go to a high
impedance state when this input is high. Chip select should stay
low during the entire communication cycle.
SDIO—Serial Data I/O
Data is always written into the AD973x on this pin. However,
this pin can be used as a bidirectional data line. The configuration of this pin is controlled by SDIO_DIR at Reg. 0, Bit 7.
The default is Logic 0, which configures the SDIO pin as
unidirectional.
SDO—Serial Data Out
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. In the case where the
AD973x operates in a single bidirectional I/O mode, this pin
does not output data and is set to a high impedance state.
MSB/LSB TRANSFERS
For multibyte transfers, writing to this register can occur during
the middle of the communication cycle. Care must be taken to
compensate for this new configuration for the remaining bytes
of the current communication cycle. The same considerations
apply to setting the software reset, RESET (Reg. 0, Bit 5). All
registers are set to their default values except Reg. 0 and Reg. 4,
which remain unchanged.
Use of only single-byte transfers when changing serial port
configurations or initiating a software reset is highly
recommended. In the event of unexpected programming
sequences, the AD973x SPI can become inaccessible. For
example, if user code inadvertently changes the LONG_INS bit
or the LSBFIRST bit, the following bits experience unexpected
results. The SPI can be returned to a known state by writing an
incomplete byte (1 to 7 bits) of all 0s followed by 3 bytes of
0x00. This returns to MSB-first short instructions
(Reg. 0 = 0x00), so the device can be reinitialized.
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
R/W N1 N0 A4 A3
A2 A1 A0 D7N D6N D5N
Figure 69. Serial Register Interface Timing, MSB-First Write
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
SCLK
SDIO
R/W N1 N0
A4
A3
A2 A1 A0
The AD973x serial port controller data address decrements
from the data address written toward 0x00 for multibyte I/O
operations if the MSB-first mode is active. The serial port
controller address increments from the data address written
toward 0x1F for multibyte I/O operations if the LSB-first mode
is active.
D6N D5N
D30 D20 D10 D00
D6N D5N
D30 D20 D10 D00
D7
SDO
When LSBFIRST = 1 (LSB first), the instruction and data bytes
must be written from least significant bit to most significant bit.
Multibyte data transfers in LSB-first format start with an
instruction byte that includes the register address of the least
significant data byte followed by multiple data bytes. The serial
port internal byte address generator increments for each byte of
the multibyte communication cycle.
D30 D20 D10 D00
04862-067
SDIO
04862-068
When LSBFIRST = 0 (MSB first), the instruction and data bytes
must be written from the most significant bit to the least
significant bit. Multibyte data transfers in MSB-first format start
with an instruction byte that includes the register address of the
most significant data byte. Subsequent data bytes should follow
in order from high address to low address. In MSB-first mode,
the serial port internal byte address generator decrements for
each data byte of the multibyte communication cycle.
SCLK
D7
Figure 70. Serial Register Interface Timing, MSB-First Read
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
SCLK
SDIO
A0
A1 A2 A3
A4 N0
N1 R/W D00 D10 D20
D4N D5N D6N D7N
04862-069
The AD973x serial port can support both MSB-first or LSB-first
data formats. This functionality is controlled by LSBFIRST at
Reg. 0, Bit 6. The default is MSB first (LSBFIRST = 0).
Figure 71. Serial Register Interface Timing, LSB-First Write
INSTRUCTION CYCLE
DATA TRANSFER CYCLE
CSB
SCLK
The AD973x serial port configuration is controlled by Reg. 0,
Bit 4, Bit 5, Bit 6, and Bit 7. Note that the configuration changes
immediately upon writing to the last bit of the register.
SDIO
A0
A1 A2
A3
A4
N0
N1 R/W
D10 D20
D4N D5N D6N D7N
D10 D20
D4N D5N D6N D7N
D0
SDO
D0
Figure 72. Serial Register Interface Timing, LSB-First Read
Rev. A | Page 37 of 72
04862-070
NOTES ON SERIAL PORT OPERATION
AD9734/AD9735/AD9736
tDS
Table 22. PIN_MODE Input Functions
tSCLK
Mnemonic
UNSIGNED
CSB
tPWH
tPWL
SCLK
2×
tDH
INSTRUCTION BIT 7
SDIO
04862-071
tDS
INSTRUCTION BIT 6
FSC1, FSC0
Figure 73. Timing Diagram for SPI Register Write
CSB
PD
SCLK
SDIO I1
I0
D7
FIFO
tDV
D6
D5
04862-072
tDNV
Figure 74. Timing Diagram for SPI Register Read
After the last instruction bit is written to the SDIO pin, the
driving signal must be set to a high impedance in time for the
bus to turn around. The serial output data from the AD973x is
enabled by the falling edge of SCLK. This causes the first output
data bit to be shorter than the remaining data bits, as shown in
Figure 74.
To assure proper reading of data, read the SDIO or SDO pin
prior to changing the SCLK from low to high. Due to the more
complex multibyte protocol, multiple AD973x devices cannot
be daisy-chained on the SPI bus. Multiple DACs should be
controlled by independent CSB signals.
PIN MODE OPERATION
When the PIN_MODE input (Pin L1) is set high, the SPI port is
disabled. The SPI port pins are remapped, as shown in Table 21.
The function of these pins is described in Table 22. The remaining PIN_MODE register settings are shown in Table 9.
Table 21. SPI_MODE vs. PIN_MODE Inputs
Pin Number
E13
F13
G13
E14
F14
G14
PIN_MODE = 0
IRQ
CSB
SCLK
RESET
SDIO
SDO
PIN_MODE = 1
UNSIGNED
2×
FSC0
PD
FIFO
FSC1
Function
0, twos complement input data format
1, unsigned input data format
0, interpolation disabled
1, interpolation = 2× enabled
00, sleep mode
01, 10 mA full-scale output current
10, 20 mA full-scale output current
11, 30 mA full-scale output current
0, chip enabled
1, chip in power-down state
0, input FIFO disabled
1, input FIFO enabled
Care must be taken when using PIN_MODE because only the
control bits shown in Table 22 can be changed. If the remaining
register default values are not suitable for the desired operation,
PIN_MODE cannot be used. If the FIFO is enabled, the
controller clock must be less than 10 MHz. This limits the DAC
clock to 160 MHz.
RESET OPERATION
The RESET pin forces all SPI register contents to their default
values (see Table 9), which places the DAC in a known state.
The software reset bit forces all SPI register contents, except
Reg. 0 and Reg. 4, to their default values.
The internal reset signal is derived from a logical OR operation
on the RESET pin state and from the software reset state. This
internal reset signal drives all SPI registers to their default
values, except Reg. 0 and Reg. 4, which are unaffected. The data
registers are not affected by either reset.
The software reset is asserted by writing 1 to Reg. 0, Bit 5. It
may be cleared on the next SPI write cycle or a later write cycle.
PROGRAMMING SEQUENCE
The AD973x registers should be programmed in this order:
1.
Reset hardware.
2.
Make changes to SPI port configuration, if necessary.
3.
Input format, if unsigned.
4.
Interpolation, if in 2× mode.
5.
Calibrate and set the LVDS controller.
6.
Enable the FIFO.
7.
Calibrate and set the sync controller.
Step 1 through Step 4 are required, while Step 5 through Step 7
are optional. The LVDS controller can help assure proper data
reception in the DAC with changes in temperature and voltage.
The sync controller manages the FIFO to assure proper transfer
of the received data to the DAC core with changes in
temperature and voltage. The DAC is intended to operate with
both controllers active unless data and clock alignment is
managed externally.
Rev. A | Page 38 of 72
AD9734/AD9735/AD9736
0.10
INTERPOLATION FILTER
0.08
0.06
0.04
MAGNITUDE (dB)
In 2× mode, the input data is interpolated by a factor of 2 so
that it aligns with the DAC update rate. The interpolation filter
is a hard-coded, 55-tap, symmetric FIR with a 0.001 dB passband flatness and a stop-band attenuation of about 90 dB. The
transition band runs from 20% of fDAC to 30% of fDAC. The FIR
response is shown in Figure 75 where the frequency axis is
normalized to fDAC. Figure 76 shows the pass-band flatness and
Table 23 shows the 16-bit filter coefficients.
Tap Weight
−7
0
+24
0
−62
0
+135
0
−263
0
+471
0
−793
0
+1273
0
−1976
0
+3012
0
−4603
0
+7321
0
−13270
0
+41505
+65535
0
–0.10
0
0.05
0.10
0.15
0.20
FREQUENCY NORMALIZED TO fDAC
0.25
04862-074
–0.08
–10
Figure 76. Interpolation Filter Pass-Band Flatness
DATA INTERFACE CONTROLLERS
Two internal controllers are utilized in the operation of the
AD973x. The first controller helps maintain optimum LVDS
data sampling; the second controller helps maintain optimum
synchronization between the DACCLK and the incoming data.
The LVDS controller is responsible for optimizing the sampling
of the data from the LVDS bus (DB13:0), while the sync
controller resolves timing problems between the DAC_CLK
(CLK+, CLK−) and the DATACLK. A block diagram of these
controllers is shown in Figure 77.
DATACLK
DATACLK_OUT
CLK
CONTROL
DATACLK_IN
DATA
SOURCE
i.e., FPGA
LVDS
CONTROLLER
SYNC
CONTROLLER
SYNC
LOGIC
LVDS
SAMPLE
LOGIC
DB<13:0>
FIFO
DAC
Figure 77. Data Controllers
The controllers are clocked with a divided-down version of the
DAC_CLK. The divide ratio is set utilizing the controller clock
predivider bits (CCD<3:0>) located at Reg. 22, Bits 3:0 to
generate the controller clock as follows:
–20
Controller Clock = DAC_CLK/(2(CCD<3:0> + 4))
–30
Note that the controller clock cannot exceed 10 MHz for correct
operation. Until CCD<3:0> is properly programmed to meet
this requirement, the DAC output may not be stable. This
means the FIFO cannot be enabled in PIN_MODE unless the
DACCLK is less than 160 MHz.
–40
–50
–60
–70
–80
–90
–100
0
0.05
0.10 0.15 0.20 0.25 0.30 0.35 0.40
FREQUENCY NORMALIZED TO fDAC
0.45
0.50
04862-073
MAGNITUDE (dB)
–0.04
04862-075
Coefficient Number
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
0
–0.02
–0.06
Table 23. FIR Interpolation Filter Coefficients
Coefficient Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
0.02
Figure 75. Interpolation Filter Response
Rev. A | Page 39 of 72
AD9734/AD9735/AD9736
DBU
The LVDS and sync controllers are independently operated in
three modes via SPI port Reg. 6 and Reg. 8:
Manual mode
•
Surveillance mode
•
Auto mode
FF
D1
FF
D2
DBL
DATA SAMPLING
SIGNAL
SD<3:0>
SAMPLE DELAY
In manual mode, all of the timing measurements and updates
are externally controlled via the SPI.
DATACLK_IN
LVDS
RX
MSD<3:0>
DELAY
In surveillance mode, each controller takes measurements and
calculates a new optimal value continuously. The result of the
measurement is passed through an averaging filter before
evaluating the results for increased noise immunity. The filtered
result is compared to a threshold value set via Reg. 6 and Reg. 8
of the SPI port. If the error is greater than the threshold, an
interrupt is triggered and the controller stops.
DELAYED
CLOCK
SIGNAL
CHECK
FF
MSD<3:0>
DELAY
CLOCK
SAMPLING
SIGNAL
04862-076
•
LVDS
RX
DB<13:0>
Figure 78. Internal LVDS Data Sampling Logic
CLK TO DB SKEW
DB13:0
Reg. 1 of the SPI port controls the interrupts with Bit 3 and Bit 2
enabling the respective interrupts and Bit 7 and Bit 6 indicating
the respective controller interrupt. If an interrupt is enabled, it
also activates the AD973x IRQ pin. To clear an interrupt, the
interrupt enable bit of the respective controller must be set to 0
for at least 1 controller clock cycle (controller clock <10 MHz).
DATACLK_IN
PROP DELAY
TO LATCH
DATA SAMPLING
SIGNAL (DSS)
PROP DELAY
TO LATCH
D1
D2
04862-077
Auto mode is almost identical to surveillance mode. Instead
of triggering an interrupt and stopping the controller, the
controller automatically updates its settings to the newly
calculated optimal value and continues to run.
SAMPLE
DELAY
Figure 79. Internal LVDS Data Sampling Logic Timing
LVDS SAMPLE LOGIC CALIBRATION
LVDS SAMPLE LOGIC
A simplified diagram of the AD973x LVDS data sampling
engine is shown in Figure 78 and the timing diagram is shown
in Figure 79.
The incoming LVDS data is latched by the data sampling signal
(DSS), which is derived from DATACLK_IN. The LVDS
controller delays DATACLK_IN to create the data sampling
signal (DSS), which is adjusted to sample the LVDS data in the
center of the valid data window. The skew between the
DATACLK_IN and the LVDS data bits (DB<13:0>) must be
minimal for proper operation. Therefore, it is recommended
that the DATACLK_IN be generated in the same manner as the
LVDS data bits (DB<13:0>) with the same driver and data lines
(that is, it should just be another LVDS data bit running a
constant 01010101… sequence, as shown in Figure 96).
If the DATACLK_IN signal is stopped, the DACCLK continues
to generate an output signal based on the last two values
clocked into the registers that drive D1 and D2, as shown in
Figure 78. If these two registers are not equal, a large output at a
frequency of one-half fDAC can be generated at the DAC output.
The internal DSS delay must be calibrated to optimize the data
sample timing. Once calibrated, the AD973x generates an IRQ
or automatically corrects its timing if temperature or voltage
variations change the timing too much. This calibration is done
using the delayed clock sampling signal (CSS) to sample the
delayed clock signal (DCS). The LVDS sampling logic finds the
edges of the DATACLK_IN signal and, from this measurement,
the center of the valid data window is located.
The internal delay line that derives the delayed DSS from
DATACLK_IN is controlled by SD3:0 (Reg. 5, Bits 7:4), while
the DCS is controlled by MSD3:0 (Reg. 4, Bits 7:4), and the CSS
is controlled by MHD3:0 (Reg. 4, Bits 3:0).
DATACLK_IN transitions must be time aligned with the LVDS
data (DB<13:0>) transitions. This allows the CSS, derived from
the DATACLK_IN, to find the valid data window of DB<13:0>
by locating the DATACLK_IN edges. The latching (rising) edge
of CSS is initially placed using Bits SD<3:0> and can then be
shifted to the left using MSD<3:0> and to the right using
MHD<3:0>. When CSS samples the DCS and the result is 1
(which can be read back via the check bit at Reg. 5, Bit 0), the
sampling occurs in the correct data cycle.
Rev. A | Page 40 of 72
AD9734/AD9735/AD9736
To find the leading edge of the data cycle, increment the
measured setup delay until the check bit goes low. To find the
trailing edge, increment the measured hold delay (MHD) until
check goes low. Always set MHD = 0 when incrementing MSD
and vice versa.
SETUP TIME (tS)
DB<13:0>
DATACLK_IN
SAMPLE DELAY SD<3:0>
MSD<3:0> = 0 1 2 3 4 5
The incremental units of SD, MSD, and MHD are in units of real
time, not fractions of a clock cycle. The nominal step size is 80 ps.
CHECK = 1 1 1 1 1 0
With SD<3:0> and MHD<3:0> set to 0, increment the setup time
delay (MSD<3:0>, Reg. 4, Bits 7:4) until the check bit (Reg. 5,
Bit 0) goes low and record this value. This locates the leading
DATACLK_IN (and data) transition, as shown in Figure 80.
With SD<3:0> and MSD<3:0> set to 0, increment the hold time
delay (MHD<3:0>, Reg. 4, Bits 3:0) until the check bit (Reg. 5,
Bit 0) goes low and record this value. This locates the trailing
DATACLK_IN (and DB<13:0>) transition, as shown in Figure
81.
Figure 81. Hold Delay Measurement
OPERATING THE LVDS CONTROLLER IN
SURVEILLANCE AND AUTO MODE
In surveillance mode, the controller searches for the edges of
the data eye in the same manner as in the manual mode of
operation and triggers an interrupt if the clock sampling signal
(CSS) has moved more than the threshold value set by
LTRH<1:0> (Reg. 6, Bits 1:0).
There is an internal filter that averages the setup and hold time
measurements to filter out noise and glitches on the clock lines.
Average Value = (MHD – MSD)/2
New Average = Average Value + (Δ Average/2 ^ LFLT<3:0>)
Once both DATACLK_IN edges are located, the sample delay
(SD<3:0>, Reg. 5, Bits 7:4) must be updated by
Sample Delay = (MHD − MSD)/2
If an accumulating error in the average value causes it to exceed
the threshold value (LTHR<1:0>), an interrupt is issued.
After updating SD<3:0>, verify that the sampling signal is in the
middle of the valid data window by adjusting both MHD and
MSD with the new sample delay until the check bit goes low.
The new MHD and MSD values should be equal to or within
one unit delay if SD<3:0> was set correctly.
MHD and MSD may not be equal to or within one unit delay if
the external clock jitter and noise exceeds the internal delay
resolution. Differences of 2, 3, or more are possible and can
require more filtering to provide stable operation.
The sample delay calibration should be performed prior to
enabling surveillance mode or auto mode.
SETUP TIME (tS)
DB<13:0>
DATACLK_IN
The maximum allowable value for LFLT<3:0> is 12. If
LFLT<3:0> is too small, clock jitter and noise can cause erratic
behavior. In most cases, LFLT can be set to the maximum value.
In surveillance mode, the ideal sampling point should first be
found using manual mode and then applied to the sample delay
registers. Set the threshold and filter values depending on how
far the CSS signal is allowed to drift before an interrupt occurs.
Then, set the surveillance bit high (Reg. 6, Bit 7) and monitor
the interrupt signal either via the SPI port (Reg. 1, Bit 7) or the
IRQ pin.
In auto mode, follow the same steps to set up the sample delay,
threshold, and filter length. To run the controller in auto mode,
both the LAUTO (Reg. 6, Bit 6) and LSURV (Reg. 6, Bit 7) bits
need to be set to 1. In auto mode, the LVDS interrupt should be
set low (Reg. 1, Bit 3) to allow the sample delay to be automatically updated if the threshold value is exceeded.
CSS SAMPLE DCS
CSS WITH
MHD<3:0> = 0
04862-078
DSC DELAYED
BY MSD<3:0>
CHECK = 1
CHECK = 1
04862-079
DSC DELAYED
BY MSD<3:0> = 0
The manual operation of the LVDS controller allows the user to
step through both the setup and hold delays to calculate the
optimal sampling delay (that is, the center of the data eye).
MSD<3:0> = 0 1 2 3 4 5
CSS SAMPLE DCS
CSS WITH
MHD<3:0> = 0
OPERATING THE LVDS CONTROLLER IN
MANUAL MODE VIA THE SPI PORT
SAMPLE DELAY SD<3:0>
HOLD TIME (tH)
Figure 80. Setup Delay Measurement
Rev. A | Page 41 of 72
AD9734/AD9735/AD9736
SYNC LOGIC AND CONTROLLER
A FIFO structure is utilized to synchronize the data transfer
between the DACCLK and the DATACLK_IN clock domains.
The sync controller writes data from DB<13:0> into an 8-word
memory register based on a cyclic write counter clocked by the
DSS, which is a delayed version of DACCLK_IN. The data is
read out of the memory based on a second cyclic read counter
clocked by DACCLK. The 8-word FIFO shown in Figure 82
provides sufficient margin to maintain proper timing under
most conditions. The sync logic is designed to prevent the read
and write pointers from crossing. If the timing drifts far enough
to require an update of the phase offset (PHOF<1:0>), two
samples are duplicated or dropped. Figure 83 shows the timing
diagram for the sync logic.
8 WORD
MEMORY
M0
DAC<13:0>
ADDER
DSS
FF
FIFOSTAT<2:0>
PHOF<1:0>
WRITE
COUNTER
READ
COUNTER
DACCLK
04862-080
ZD
To start operating the DAC in manual mode, allow DACCLK
and DATACLK_IN to stabilize, then enable FIFO mode (Reg. 0,
Bit 2). Read FIFOSTAT<2:0> (Reg. 7, Bits 6:4) to determine if
adjustment is needed. For example, if FIFOSTAT<2:0> = 6, the
timing is not yet critical, but it is not optimal.
To return to an optimal state (FIFOSTAT<2:0> = 4), the
PHOF<1:0> (Reg. 7, Bits 1:0) needs to be set to 1. Setting
PHOF<1:0> = 1 effectively increments the read pointer by 2.
This causes the write pointer value to be captured two clocks
later, decreasing FIFOSTAT<2:0> from 6 to 4.
OPERATION IN SURVEILLANCE AND AUTO MODES
Once FIFOSTAT<2:0> is manually placed in an optimal state,
the AD973x sync logic can run in surveillance or auto mode. To
start, turn on surveillance mode by setting SSURV = 1 (Reg. 8,
Bit 7), then enable the sync interrupt (Reg. 1, Bit 2).
If STRH<0> = 0 (Reg. 8, Bit 0), an interrupt occurs if
FIFOSTAT<2:0> = 0 or 7. If STRH<0> = 1 (Reg. 8, Bit 0), an
interrupt occurs if FIFOSTAT<2:0> = 0, 1, 6, or 7. The interrupt
is read at Reg. 1, Bit 6 at the AD973x IRQ pin.
DAC<13:0>
M7
OPERATION IN MANUAL MODE
Figure 82. Sync Logic Block Diagram
SYNC LOGIC AND CONTROLLER OPERATION
The relationship between the readout pointer and the write
pointer initially is unknown because the startup relationship
between DACCLK and DATACLK_IN is unknown. The sync
logic measures the relative phase between the two counters with
the zero detect block and the flip-flop in Figure 82. The relative
phase is returned in FIFOSTAT<2:0> (Reg. 7, Bits 6:4), and sync
logic errors are indicated by FIFOSTAT<3> (Reg. 7, Bit 7). If
FIFOSTAT<2:0> returns a value of 0 or 7, the memory is
sampling in a critical state (read and write pointers are close to
crossing).
If the FIFOSTAT<2:0> returns a value of 3 or 4, the memory is
sampling at the optimal state (read and write pointers are
farthest apart). If FIFOSTAT<2:0> returns a critical value, the
pointer can be adjusted with the phase offset PHOF<1:0> (Reg.
7, Bits 1:0). Due to the architecture of the FIFO, the phase offset
can only adjust the read pointer in steps of 2.
To enter auto mode, complete the preceding steps then set
SAUTO = 1 (Reg. 8, Bit 6). Next, set the sync interrupt = 0
(Reg. 1, Bit 2), to allow the phase offset (PHOF<1:0>) to be
automatically updated if FIFOSTAT<2:0> violates the threshold
value. The FIFOSTAT signal is filtered to improve noise
immunity and reduce unnecessary phase offset updates. The
filter operates with the following algorithm:
FIFOSTAT = FIFOSTAT + ΔFIFOSTAT/2 ^ SFLT<3:0>
where:
0 ≤ SFLT<3:0> ≤ 12
Values greater than 12 are set to 12. If SFLT<3:0> is too small,
clock jitter and noise can cause erratic behavior. Normally, SFLT
can be set to the maximum value.
FIFO BYPASS
When the FIFO_MODE bit (Reg. 1, Bit 2) is set to 0, the FIFO
is bypassed with a mux. When the FIFO is enabled, the pipeline
delay through the AD973x increases by the delta between the
FIFO read pointer and write pointer plus 4 more clock periods.
Rev. A | Page 42 of 72
AD9734/AD9735/AD9736
DACCLK
INTERNAL DELAY
DATACLK_OUT
EXTERNAL DELAY
DATACLK_IN
DATA_IN
A
C
B
D
E
F
G
I
H
J
K
L
M
N
P
O
Q
R
SAMPLE_HOLD
SAMPLE_SETUP
SAMPLE_DELAY
DSS1
C
A
D1
G
E
I
Q
O
M
K
DSS2
0
2
1
3
H
F
4
5
6
7
2
3
B
DATA 'A' CAN BE
SAFELY READ FROM
THE FIFO IN THE
SAFE ZONE. IN THE
ERROR ZONE, THE
POINTERS MAY
BRIEFLY OVERLAP
DUE TO CLOCK JITTER
OR NOISE.
0
FIFOSTAT IS SET
EQUAL TO THE
WRITE POINTER
EACH TIME THE
READ POINTER
CHANGES FROM
7 TO 0.
D
E
F
G
H
M7
DAC_DATA
7
C
M6
FIFOSTAT
6
J
M2
READ_PTR1
5
4
P
I
M1
M5
1
N
A
M0
M4
0
L
ERROR ZONE
SAFE ZONE
M3
J
4
5
6
7
0
1
2
3
4
4
5
6
7
0
1
2
4
A
B
C
D
3
4
4
E
F
Figure 83. Sync Logic Timing Diagram
Rev. A | Page 43 of 72
G
H
I
J
K
L
M
04862-081
WRITE_PTR1
D
B
D2
AD9734/AD9735/AD9736
DIGITAL BUILT-IN SELF TEST (BIST)
OVERVIEW
Placing the idle value on the data input also allows the BIST to
be set up while the DAC clock is running. The idle value should
be all 0s in unsigned mode (0x0000) and all 0s except for the
MSB in twos complement mode (0x2000).
The AD973x includes an internal signature generator that
processes incoming data to create unique signatures. These
signatures are read back from the SPI port, allowing verification
of correct data transfer into the AD973x. BIST vectors provided
on the AD973x-EB evaluation board CD check the full width
data input or individual bits for PCB debug, utilizing the
procedure in the AD973X BIST Procedure section. Alternatively, any vector can be used provided the expected signature is
calculated in advance.
The BIST consists of two stages; the first stage is after the LVDS
receiver and the second stage is after the FIFO. The first BIST
stage verifies correct sampling of the data from the LVDS bus
while the second BIST stage verifies correct synchronization
between the DAC_CLK domain and the DATACLK_IN
domain. The BIST vector is generated using 32-bit LFSR
signature logic. Because the internal architecture is a 2-bus
parallel system, there are two 32-bit LFSR signature logic blocks
on both the LVDS and SYNC blocks. Figure 84 shows where the
LVDS and SYNC phases are located.
The MATLAB® routine, in the Generating Expected Signatures
section, calculates the expected signature. BIST verifies correct
data transfer because not all errors are always evident on a
spectrum analyzer. There are four BIST signature generators
that can be read back using Reg. 18 to Reg. 21, based on the
setting of the BIST selection bits (Reg. 17, Bits 7:6), as shown in
Table 24. The BIST signature returned from the AD973x
depends on the digital input during the test. Because the filters
in the DAC have memory, it is important to put the correct idle
value on the DATA input to flush the memory prior to reading
the BIST signature.
Table 24. BIST Selection Bits
Bit
LVDS Phase 1
LVDS Phase 2
SYNC Phase 1
SYNC Phase 2
SEL<1>
0
0
1
1
SEL<0>
0
1
0
1
D1
DB<13:0>
LVDS
BIST
PH1
(RISE)
LVDS
RX
DATACLK_IN
FIFO
2x
SYNC
BIST
PH1
(RISE)
DAC
D2
SYNC LOGIC
SYNC
BIST
PH2
(FALL)
SPI PORT
Figure 84. Block Diagram Showing LVDS and SYNC Phase 1 and SYNC Phase 2
Rev. A | Page 44 of 72
04862-082
LVDS
BIST
PH2
(FALL)
AD9734/AD9735/AD9736
AD973x BIST PROCEDURE
17.
Read all signature registers (Reg. 21, Reg. 20, Reg. 19, and
Reg. 18, as described in Step 14 ) for each of the four SEL
(Reg. 17, Bits 7:6) values, and verify that they match the
expected signatures shown in Table 25.
18.
Flush the BIST circuitry. This must be done once before
valid data can be read. Loop back to Step 11 and rerun the
test to obtain the correct result.
1.
Set RESET pin = 1.
2.
Set input DATA = 0x0000 for signed (0x2000 for
unsigned).
3.
Enable DATACLK_IN if it is not already running.
4.
Run for at least 16 DATACLK_IN cycles.
5.
Set RESET pin = 0.
6.
Run for at least 16 DATACLK_IN cycles.
7.
Set RESET pin = 1.
8.
Run for at least 16 DATACLK_IN cycles.
AD973x EXPECTED BIST SIGNATURES
9.
Set RESET pin = 0.
10.
Set desired operating mode (1× mode and signed data are
default values and expected for the supplied BIST vectors).
The BIST vectors provided on the AD973x-EB CD are in signed
mode, so no programming is necessary for the part to pass the
BIST. The BIST vector is for 1×, no FIFO, and signed data.
11.
Set CLEAR (Reg. 17, Bit 0), SYNC_EN (Reg. 17, Bit 1),
and LVDS_EN (Reg. 17, Bit 2) high.
For testing all 14 input bits, use the vector all_bits_unsnew.txt
and verify against the signatures in Table 25.
12.
Wait 50 DATACLK_IN cycles to allow 0s to propagate
through and clear sync signatures.
Table 25. Expected BIST Data Readback for All Bits
13.
Set CLEAR low.
14.
Read all signature registers (Reg. 21, Reg. 20, Reg. 19, and
Reg. 18) for each of the four SEL (Reg. 17, Bits 7:6) values
and verify they are all 0x00.
LVDS Phase 1
a.
Reg. 17 set to 0x26 (SEL1 = 0, SEL0 = 0,
SIG_READ = 1, LVDS_EN = 1, SYNC_EN = 1).
b. Read Reg. 20, Reg. 19, Reg. 18, and Reg. 17.
LVDS Phase 2
a.
Reg. 17 set to 0x66 (SEL1= 0, SEL0 = 1,
SIG_READ = 1, LVDS_EN = 1, SYNC_EN = 1).
b.
Read Reg. 20, Reg. 19, Reg. 18, and Reg. 17.
SYNC Phase 1
a. Reg. 17 set to 0xA6 (SEL1= 1, SEL0 = 0,
SIG_READ = 1, LVDS_EN = 1, SYNC_EN = 1).
b. Read Reg. 20, Reg. 19, Reg. 18, and Reg. 17.
SYNC Phase 2
a. Reg. 17 set to 0xE6 (SEL1= 1, SEL0 = 1,
SIG_READ = 1, LVDS_EN = 1, SYNC_EN = 1).
b. Read Reg. 20, Reg. 19, Reg. 18, and Reg. 17.
Each time BIST mode is entered, this flush needs to
be performed once. Multiple BIST runs can be performed
without reflushing, as long as the device remains in
BIST mode.
LVDS Phase 1
CF71487C
15.
Clock the BIST vector into the AD973x.
16.
After the BIST vector is clocked into the part, hold DATA
= 0x0000 for signed (0x2000 for unsigned); otherwise, the
additional nonzero data changes the signature.
LVDS Phase 2
66DF5250
SYNC Phase 1
CF71487C
SYNC Phase 2
66DF5250
For individual bit tests, use the vectors named bitn.txt (where n
is the desired bit number being tested) and compare them
against the values in Table 26.
Table 26. Expected BIST Data Readback for Individual Bits
Vector
bit0.txt
bit1.txt
bit2.txt
bit3.txt
bit4.txt
bit5.txt
bit6.txt
bit7.txt
bit8.txt
bit9.txt
bit10.txt
bit11.txt
bit12.txt
bit13.txt
Bit
Number
0
1
2
3
4
5
6
7
8
9
10
11
12
13
LVDS Rise
Expected
AABF0A00
2BBF0A00
29BE0A00
2DBC0A00
25B80A00
35B00A00
15A00A00
55800A00
D5C00A00
D5410A00
D5430B00
D5470900
D54F0D00
D55F0500
LVDS Fall
Expected
2A400500
6B400500
E9400500
ED410500
E5430500
F5470500
D54F0500
955F0500
157F0500
153E0500
15BC0500
15B80400
15B00600
15A00200
Note the following for Table 26:
•
The term rise refers to Phase 1 and fall refers to Phase 2.
•
Byte order is Decimal Register Address 21, Address 20,
Address 19, and Address 18.
•
SYNC phase should always equal LVDS phase in 1× mode.
Rev. A | Page 45 of 72
AD9734/AD9735/AD9736
GENERATING EXPECTED SIGNATURES
To generate the expected BIST signatures, follow this procedure:
The following MATLAB code duplicates the internal logic of
the AD973x. To use it, save this code in a file called bist.m.
1.
--- begin bist.m --function [ ret1 , ret2] = bist(vec)
ret1 = bist1(vec(1:2:length(vec)-1));
ret2 = bist1(vec(2:2:length(vec)));
function ret = bist1(v)
sum = zeros(1,32);
for i = 1 :length(v)
if v(i) ~= 0
su(1) = ~xor(sum(32) ,bitget(v(i),1));
su(2) = ~xor(sum(1) ,bitget(v(i),2));
su(3) = ~xor(sum(2) ,bitget(v(i),3));
su(4) = ~xor(sum(3) ,bitget(v(i),4));
su(5) = ~xor(sum(4) ,bitget(v(i),5));
su(6) = ~xor(sum(5) ,bitget(v(i),6));
su(7) = ~xor(sum(6) ,bitget(v(i),7));
su(8) = ~xor(sum(7) ,bitget(v(i),8));
su(9) = ~xor(sum(8) ,bitget(v(i),9));
su(10) = ~xor(sum(9) ,bitget(v(i),10));
su(11) = ~xor(sum(10) ,bitget(v(i),11));
su(12) = ~xor(sum(11) ,bitget(v(i),12));
su(13) = ~xor(sum(12) ,bitget(v(i),13));
su(14) = ~xor(sum(13) ,bitget(v(i),14));
su(15) = sum(14); su(16) = sum(15);
su(17) = sum(16); su(18) = sum(17);
su(19) = sum(18); su(20) = sum(19);
su(21) = sum(20); su(22) = sum(21);
su(23) = sum(22); su(24) = sum(23);
su(25) = sum(24); su(26) = sum(25);
su(27) = sum(26); su(28) = sum(27);
su(29) = sum(28); su(30) = sum(29);
su(31) = sum(30); su(32) = sum(31);
sum = su;
end
end % for ret = dec2hex( 2.^[0:31]× sum',8);
--- end bist.m ---
Start MATLAB and type the following at the command
prompt:
t = round(randn(1,100) × 213/8+213) ;
[ b1 b2 ] = bist(t)
The first statement creates a random vector of 14-bit
words, with a length of 100.
2.
Set t equal to any desired vector, or take this random vector
and input it to the AD973x.
3.
Alter the command randn(1,100) to change the vector
length as desired.
4.
Type b1 at the command line to see the calculated
signature for the LVDS BIST, Phase 1.
5.
Type b2 to see the value for LVDS BIST, Phase 2.
The values returned for b1 and b2 each are 32-bit hex values.
They correspond to Reg. 18, Reg. 19, Reg. 20, and Reg. 21,
where b1 is the value read for SEL<1:0> = 0, 0 (see Table 17)
and b2 is the value read for SEL<1:0> = 0, 1.
When the DAC is in 1× mode, the signature at SYNC BIST,
Phase 1 should equal the signature at LVDS BIST, Phase 1. The
same is true for Phase 2.
Rev. A | Page 46 of 72
AD9734/AD9735/AD9736
CROSS CONTROLLER REGISTERS
Figure 85 shows the effect of UPDEL and DNDEL.
If the system is calibrated after manufacture, adjust the cross
controller offsets to provide optimum performance. To start,
increment DNDEL<5:0> (Reg. 11, Bits 5:0) while observing
HD2 (second harmonic distortion) and/or IMD to find the
desired optimum. If DNDEL does not influence the performance, set it to 0 and increment UPDEL<5:0> (Reg. 10, Bits 5:0).
Based on system characterization, set one of these controls to
the maximum value to yield the best performance.
Rev. A | Page 47 of 72
INCREMENT DNDEL TO MOVE
THE CROSSING TOWARD THE
IDEAL VALUE
IDEAL DIFFERENTIAL OUTPUT
CROSSING ALIGNMENT
INCREMENT UPDEL TO MOVE
THE CROSSING TOWARD THE
IDEAL VALUE
04862-083
The AD973x differential output stage is adjustable to equalize
the charge injection into the positive and negative outputs. This
adjustment impacts certain performance characteristics, such as
harmonic distortion or IMD. System performance can be enhanced by adjusting the cross controller.
Figure 85. Effect of UPDEL and DNDEL
AD9734/AD9735/AD9736
ANALOG CONTROL REGISTERS
–110
The AD973x includes some registers for optimizing its analog
performance. These registers include temperature trim for the
band gap, noise reduction in the output current mirror, and
output current mirror headroom adjustments.
NOISE (IdBm/Hz)
–115
BAND GAP TEMPERATURE CHARACTERISTIC
TRIM BITS
Using TRMBG<2:0> (Reg. 14, Bits 2:0), the temperature
characteristic of the internal band gap can be trimmed to
minimize the drift over temperature, as shown in Figure 86.
–120
MSEL3
–125
MSEL1
–130
MSEL0
MSEL2
04862-0-085
–135
1.23
–140
1
10
F (kHz)
Figure 87. 1/f Noise with Respect to MSEL Bits
VREF (V)
001
1.21
010
HEADROOM BITS
011
HDRM<7:0> (Reg. 15, Bits 7:0) are for internal evaluation.
Changing the default reset values is not recommended.
100
1.2
101
VOLTAGE REFERENCE
110
1.19
0
10
20
30
40
50
60
70
04862-084
111
1.18
–50 –40 –30 –20 –10
100
80
90
The AD973x output current is set by a combination of digital
control bits and the I120 reference current, as shown in
Figure 88.
TEMPERATURE (°C)
AD973x
Figure 86. Band Gap Temperature Characteristic for Various TRMBG Values
FSC<9:0>
VBG
1.2V
The temperature changes are sensitive to process variations,
and Figure 86 may not be representative of all fabrication lots.
Optimum adjustment requires measurement of the device
operation at two temperatures and development of a trim
algorithm to program the correct TRMBG<2:0> values in
external nonvolatile memory.
VREF
–
I120
1nF
+
10kΩ
AVSS
DAC
CURRENT
SCALING
IFULL-SCALE
I120
04862-086
1.22
000
Figure 88. Voltage Reference Circuit
MIRROR ROLL-OFF FREQUENCY CONTROL
With MSEL <1:0> (Reg. 14, Bits 7:6), the user can adjust the
noise contribution of the internal current mirror to optimize
the 1/f noise. Figure 87 shows MSEL vs. the 1/f noise with
20 mA full-scale current into a 50 Ω resistor.
The reference current is obtained by forcing the band gap
voltage across an external 10 kΩ resistor from I120 (Pin B14) to
ground. The 1.2 V nominal band gap voltage (VREF) generates a
120 μA reference current in the 10 kΩ resistor. This current is
adjusted digitally by FSC<9:0> (Reg. 2, Reg. 3) to set the output
full-scale current IFS:
I FS =
Rev. A | Page 48 of 72
VREF ⎛
192
⎞
× ⎜ 72 + ⎛⎜
× FSC < 9.0 > ⎞⎟ ⎟
R
⎝ 1024
⎠⎠
⎝
AD9734/AD9735/AD9736
The full-scale output current range is approximately 10 mA to
30 mA for register values from 0x000 to 0x3FF. The default
value of 0x200 generates 20 mA full scale. The typical range is
shown in Figure 89.
VREF (Pin C14) must be bypassed to ground with a 1 nF
capacitor. The band gap voltage is present on this pin and can
be buffered for use in external circuitry. The typical output
impedance is near 5 kΩ. If desired, an external reference can be
used to overdrive the internal reference by connecting it to the
VREF pin.
35
30
25
20
IPTAT (Pin D14) is used for factory testing. Leave this pin
floating.
15
10
5
0
04862-087
IFS (mA)
Always connect a 10 kΩ resistor from the I120 pin to ground
and use the digital controls to vary the full-scale current. The
AD973x is not a multiplying DAC. Applying an analog signal to
I120 is not supported.
0
200
400
600
800
1000
DAC GAIN CODE
Figure 89. IFS vs. DAC Gain Code
Rev. A | Page 49 of 72
AD9734/AD9735/AD9736
APPLICATIONS INFORMATION
DRIVING THE DACCLK INPUT
0.1μF
VCM = 400mV
CLK–
04862-088
50Ω
0.1μF
50Ω
CLK+
CLK–
50Ω BAV99ZXCT
HIGH SPEED
DUAL DIODE
VCM = 400mV
Figure 91. TTL or CMOS DACCLK Drive Circuit
A simple bias network for generating VCM is shown in
Figure 92. It is important to use CVDD18 and CVSS for the
clock bias circuit. Any noise or other signal that is coupled onto
the clock is multiplied by the DAC digital input signal and may
degrade the DAC performance.
CLK+
50Ω
LVDS_N_IN
0.1μF
VCM = 400mV
Figure 90. LVDS DACCLK Drive Circuit
If a clean sine clock is available, it can be transformer-coupled
to DACCLK, as shown in Figure 107. Use of a CMOS or TTL
clock can also be acceptable for lower sample rates. It is routed
through a CMOS to LVDS translator, then ac-coupled, as
described previously. Alternatively, it can be transformercoupled and clamped, as shown in Figure 91.
Rev. A | Page 50 of 72
CVDD
1.8V
1kΩ
1nF
287Ω
0.1µF
1nF
CVSS
Figure 92. DACCLK VCM Generator Circuit
04862-090
LVDS_P_IN
TTL OR CMOS
CLK INPUT
04862-089
The DACCLK input requires a low jitter differential drive
signal. It is a PMOS input differential pair powered from the
1.8 V supply, so it is important to maintain the specified 400 mV
input common-mode voltage. Each input pin can safely swing
from 200 mV p-p to 800 mV p-p about the 400 mV commonmode voltage. While these input levels are not directly LVDS
compatible, DACCLK can be driven by an offset ac-coupled
LVDS signal, as shown in Figure 90.
AD9734/AD9735/AD9736
DAC OUTPUT DISTORTION SOURCES
This is the configuration implemented on the evaluation board
(Figure 107). The 20 Ω series resistors allow the DAC to drive a
less reactive load, which improves distortion. Further improvement
is realized by adding the Balun T3 to help provide an equal load
to both DAC outputs.
The DAC architecture inherently generates third harmonics, the
levels of which depend on the output frequency and amplitude
generated. If any output signal is rectified and coupled back
onto the DAC clock, it can generate additional third-harmonic
energy.
The distortion components should be identical in amplitude
and phase at both AD973x outputs. Even though each singleended output includes a large amount of second-harmonic
energy, a careful differential-to-single-ended conversion can
remove most of it. Optimum performance at high intermediate
frequency (IF) output is obtained with the output circuit shown
in Figure 93.
IOUTA
R19
20Ω
R8
50Ω
R6
50Ω
IOUTB
1
T3
J2, 50Ω OUTPUT
5
6
5
1
4
4
3
AVSS
3
R17
20Ω
T1
AVSS
04862-091
The second harmonic is mostly due to an imbalance in the
output load. The dc transfer characteristic of the DAC is capable
of second harmonic distortion of at least −75 dBc. Output load
imbalance or digital data noise coupling onto DACCLK causes
additional second harmonic distortion.
Figure 93. IF Signal Output Circuit
Because T1 has a differential input, but a single-ended output,
Pin 4 of T1 has a higher capacitance to ground due to parasitics
to Pin 3. T1 Pin 6 has lower parasitic capacitance to ground
because it drives 50 Ω at Pin 1. This presents an unbalanced
load to the DAC output, so T3 is added to improve the load
balancing. Refer to Figure 107 for the transformer part numbers.
Rev. A | Page 51 of 72
AD9734/AD9735/AD9736
DC-COUPLED DAC OUTPUT
An alternate circuit is shown in Figure 95. It suffers from dc
offset at the output unless the DAC load resistors are small,
relative to the amplifier gain and feedback resistors.
0.5V p-p
0V TO –0.5V
IOUTA
DAC OUTPUT
20mA
FULL SCALE
IOUTB
100Ω
25Ω
1kΩ
2kΩ
AVSS
25Ω
1kΩ
2V p-p
0V TO –2V
OUTPUT
2kΩ
AVSS
2V p-p
0V TO –2V
IOUTA
Figure 95. Differential Op Amp Output Circuit
100Ω
500Ω
OUTPUT
AVSS
100Ω
500Ω
IOUTB
2V p-p
+1V TO –1V
500Ω
AVSS
100Ω
04862-092
DAC
OUTPUT
20mA
FULL SCALE
500Ω
Figure 94. Op Amp I to V Conversion Output Circuit
Rev. A | Page 52 of 72
04862-093
In some cases, it may be desirable to dc-couple the AD973x
output. The best method for doing this is shown in Figure 94.
This circuit can be used with voltage or current feedback
amplifiers. Because the DAC output current is driving a virtual
ground, this circuit may offer enhanced settling times. The
settling time is limited by the op amp rather than by the DAC.
This circuit is intended for use where the amplifiers can be
powered by a bipolar supply.
AD9734/AD9735/AD9736
DAC DATA SOURCES
The circuit shown in Figure 96 allows optimum data alignment
when running the AD973x at full speed. This circuit can be
easily implemented in the FPGA or ASIC used to drive the
digital input. It is important to use the DATACLK_OUT signal
because it helps to cancel some of the timing errors. In this
configuration, DATACLK_OUT generates the DDR LVDS
DATACLK_IN to drive the AD973x. The circuit aligns the
DATACLK_IN and the digital input data (DB<13:0>) as
required by the AD973x. The LVDS controller in the AD973x
uses DATACLK_IN to generate the internal DSS to capture the
incoming data in the center of the valid data window.
To operate in 2× mode, the circuit in Figure 96 must be
modified to include a divide-by-2 block in the path of
DATACLK_OUT. Without this additional divider, the data and
DATACLK_IN runs 2× too fast. DATACLK_OUT is always
DACCLK/2.
Contact FPGA vendors directly regarding the maximum output
data rates supported by their products.
DATA SOURCE
DATA SOURCE
D1
DATA1
DB(13:0) TO AD9736
MUX
DATA2
DATA2
LOGIC 1
LOGIC 0
04862-094
DATACLK_IN
TO AD9736 (DDR)
MUX
DB(13:0) TO AD9736
MUX
DATACLK_IN
TO AD9736 (DDR)
D2
D2
LOGIC 0
LOGIC 1
MUX
04862-096
D1
DATA1
DATACLK_OUT
FROM AD9736 (DDR)
÷2
DATACLK_OUT
FROM AD9736 (DDR)
Figure 96. Recommended FPGA/ASIC Configuration for Driving AD9736
Digital Inputs, 1× Mode
Figure 98. Recommended FPGA/ASIC Configuration for Driving AD9736
Digital Inputs, 2× Mode
DATACLK_OUT+
DATACLK_OUT+
DATA2
D1
A
C
D
B
A
DATA1
C
D2
DB
CLK_OUT+/2
E
D
B
A
DATA2
B
D1
C
A
C
D
B
A
C
04862-095
Figure 97. FPGA/ASIC Timing for Driving AD973x Digital Inputs, 1× Mode
DB
DATACLK_IN+
D
B
D2
DATACLK_IN+
E
A
B
C
04862-097
DATA1
Figure 99. FPGA/ASIC Timing for Driving AD973x Digital Inputs, 2× Mode
Rev. A | Page 53 of 72
AD9734/AD9735/AD9736
INPUT DATA TIMING
The AD973x is intended to operate with the LVDS and sync
controllers running to compensate for timing drift due to
voltage and temperature variations. In this mode, the key to
correct data capture is to present valid data for a minimum
amount of time. The AD973x minimum valid data time is
measured by increasing the input data rate to the point of
failure. The nominal supply voltages are used and the
temperature is set to the worst case of 85°C. The input
data is verified via the BIST signature registers, because the
DAC output does not run as fast as the input data logic. The
following example explains how the minimum data valid
period is calculated for the typical performance case.
The ability of the AD973x to capture incoming data is
dependent on the speed of the silicon, which varies from lot to
lot. The typical (or average) silicon speed operates with data
that is valid for 225 ps at 85°C. Statistically, the worst extreme
for slow silicon may require up to a 344 ps valid data period, as
specified in Table 2.
Table 27. Typical Minimum Data Valid Times
Differential Input
Voltage
400 mV
250 mV
These factors must be considered in determining the minimum
valid data window at the receiver input:
• Data rise and fall times: 100 ps (rise + fall)
• Internal clock jitter: 10 ps
(DATACLK_OUT + DATACLK_IN)
• Bit-to-bit skew: 50 ps
• Bit-to-DATACLK_IN skew: 50 ps
• Internal data sampling signal resolution: 80 ps
For nominal silicon, the BIST typically indicates failure at
2.15 GSPS or a DACCLK period of 465 ps. The valid data
window is calculated by subtracting all the other variables
from the total data period:
Minimum Data Valid Time = DACCLK Period − Data Rise −
Data Fall − Jitter − Bit-to-Bit Skew − Bit-to-DATACLK_IN Skew
− Data Sampling Signal Resolution
BIST
Max fCLK
2.15 GHz
2.00 GHz
Min Clock
Period
465 ps
500 ps
Typ Min Data
Valid at Receiver
225 ps
260 ps
At 1.2 GHz, the typical 400 mV p-p minimum data valid period
of 225 ps leaves 608 ps for external factors. Under the same
conditions, the worst expected minimum data valid period of
344 ps leaves 489 ps for external data uncertainty.
The 100 mV LVDS VOD threshold test is a dc test to verify that
the input logic state changes. It does not indicate the operating
speed. The ability of the receiver to recover the data depends on
the input signal overdrive. With a 250 mV input, there is a
150 mV overdrive, and with a 400 mV signal, there is a 300 mV
overdrive. The relationship between overdrive level and timing
is very nonlinear. Higher levels of overdrive result in smaller
minimum valid data windows.
For typical silicon, decreasing the LVDS swing from 400 mV p-p
to 250 mV p-p requires the minimum data valid period to
increase by 15%. This is illustrated in Figure 100.
225ps
For the 400 mV p-p LVDS signal case:
400mV
Minimum Data Valid = 465 ps − 100 ps − 10 ps − 50 ps −
80 ps = 465 ps − 240 ps = 225 ps
260ps
04862-098
250mV
For correct data capture, the input data must be valid for 225 ps.
Slower edges, more jitter, or more skew require an increase in
the clock period to maintain the minimum data valid period.
Table 27 shows the typical minimum data valid period (tMDE) for
400 mV p-p differential and 250 mV p-p differential LVDS swings.
Figure 100. Typical Minimum Valid Data Time (tMDE) vs. LVDS Swing
The minimum valid data window changes with temperature,
voltage, and process. The maximum value presented in the
specification table was determined from a 6σ distribution in the
worst-case conditions.
Rev. A | Page 54 of 72
AD9734/AD9735/AD9736
SYNCHRONIZATION TIMING
When more than one AD973x must be synchronized or when
a constant group delay must be maintained, the internal
controllers cannot be used. If the FIFO is enabled, the delay
between multiple AD973x devices is unknown. If the
DATACLK_OUT from multiple devices is used, there is an
uncertainty of two DACCLK periods because the initial phase
of DATACLK_OUT with respect to DACCLK cannot be
controlled. This means one DAC must be used to provide
DATACLK_OUT for all synchronized DACs and all timing
must be externally managed. The following timing information
allows system timing to be calculated so that multiple AD973xs
can be synchronized.
DATACLK_OUT changes relative to the rising edge of
DACCLK+ and is delayed, as shown in Figure 101. Because
DACCLK is divided by 2 to create DATACLK_OUT, the phase
of DATACLK_OUT can be 0° or 180°. There is no way to
predict or control this relationship. It can be different after each
power cycle and is not affected by hardware or software resets.
DACCLK
tDDCO
04862-099
DATACLK_OUT
Figure 101. DACCLK to DATACLK_OUT Delay
The incoming data is de-interleaved internally as shown in
Figure 78. In Figure 78, DBU (upper) and DBL (lower) represent
the de-interleaved data paths. Each edge of DATACLK_IN
latches an incoming sample in two alternating registers. The
DATACLK_IN to data setup and hold definitions are illustrated
in Figure 102. All the data input must be valid during the setupand-hold period. External skew effectively increases the setup
and hold times that the data source must meet.
DATACLK_IN
OR DATACLK_OUT
While correct DATA_IN vs. DATACLK_IN timing is critical,
the transition of the incoming data to the DACCLK domain is
equally critical. By referencing the incoming DATA and
DATACLK_IN timing to the DATACLK_OUT signal, some
timing uncertainty can be removed. The DATACLK_OUT
timing very closely tracks the timing of the DACCLKcontrolled registers. Any variation in the path delay affects both
paths in almost the same way. If DATACLK_OUT is not used,
the full DACCLK to DATACLK_OUT path variation reduces
the external timing margin. Figure 101 shows a simplified view
of the internal clocking scheme with the relevant delay paths.
The internal architecture is interleaved such that each phase has
twice as long to make the transition across the clock domains.
This results in an extremely narrow window where the
incoming data must be held stable.
Table 28 shows the timing parameters for Figure 101 and
Figure 102. These parameters were measured for a sample of
five devices from five silicon lots. Worst-case fast and slow skew
lots were included in addition to the nominal (or average) lot.
The typical −40°C to typical +85°C spread illustrates the
variability with temperature for a single lot. Adding in lot-to-lot
variation with the fast and slow lots indicates the worst-case
spread in timing.
The timing varies such that all of the parameters move in the
same direction. For example, if the DATACLK_IN to data setup
time is fast, the hold time is similarly fast. The DACCLK to
DATACLK_OUT delay and the DATACLK_OUT to data setup
and hold is also at the fast end of the range.
Note that the polarities of setup-and-hold values in Table 28
conform to the standard convention of setup time occurring
prior to the latching edge and hold time occurring after the
latching edge, as shown in Figure 102.
tDSU
tDH
04862-100
DATA_IN
Figure 102. Standard Definitions for DATACLK_IN or DATACLK_OUT to
Data Setup and Hold, SD = 0
Table 28. AD973x Clock and Data Timing Parameters
Symbol and Definition
tDDCO − DACCLK to DATACLK_OUT Delay
tDCISU − DATACLK_IN to DATA Setup
tDCIH − DATACLK_IN to DATA Hold
tDISU − DATACLK_OUT to DATA Setup
tDIH − DATACLK_OUT to DATA Hold
Fast −40°C
+1650
−100
+210
+1310
−1250
Typ −40°C
+1800
−120
+220
+1440
−1360
Rev. A | Page 55 of 72
All +25°C
+1890
−150
+240
+1611
−1548
Typ +85°C
+2050
−170
+280
+1710
−1640
Slow +85°C
+2350
−220
+360
+1970
−1890
Unit
ps
ps
ps
ps
ps
AD9734/AD9735/AD9736
POWER SUPPLY SEQUENCING
The 1.8 V supplies should be enabled prior to enabling the 3.3 V supplies. Do not enable the 3.3 V supplies when the
1.8 V supplies are off.
DATACLK_IN DOMAIN
DACCLK DOMAIN
D1
FF
DAC_DATA
LVDS
RX
FF
DATA SAMPLING
SIGNAL
SD<3:0>
SD<3:0>
SAMPLE DELAY
DELAY
SAMPLE
DATACLK_IN
DATACLK_OUT
LVDS
RX
LVDS
TX
DAC
CORE
DAC_OUTPUT
D2A
D2
FF
DAC SAMPLING
SIGNAL
PATH A
÷2
CLK
RX
DACCLK
PATH B
COMMON SYSTEM CLOCK
DELAYS THROUGH PATH A AND B WILL TRACK,
THUS REDUCING TIMING UNCERTAINTY IN THE SYSTEM
Figure 103. Simplified Internal Clock Routing
Rev. A | Page 56 of 72
04862-101
DB<13:0>
D1A
FF
AD9734/AD9735/AD9736
AD973X EVALUATION BOARD SCHEMATICS
TP4
RED
FERRITE
VDD33
LC1210
+
ACASE
C14
10μF
6.3V
VSS
TB1 2
L7
TP7
RED
FERRITE
LC1210
18DIG
TB1 3
VSS
TP5
BLK
L5
VDD18B
+
C22
ACASE 10μF
6.3V
FERRITE
LC1210
TP13
BLK
TP6
RED
+
ACASE
VSS
TB1 4
VSS
VDD18A
L1, L3, L4, L5, L6, AND L7
FERRITE BEAD CORE:
PANASONIC EXC–CL3225U1
DIGIKEY PN: P9811CT–ND
C18
10μF
6.3V
TP14
BLK
VSS
JP1
VSS
L1
33ANA
TB2 1
FERRITE
LC1210
VSSA
TB2 4
C1
10μF
6.3V
TP3
BLK
L3
FERRITE
LC1210
L4
VSSA
POWER INPUT FILTERS
TP9
RED
VDDC
+
ACASE
FERRITE
LC1210
VSSA
UNDER DUT
VDDA33
+
ACASE
VSSA
TB2 2
18ANA
TB2 3
TP1
RED
C10
10μF
6.3V
TP11
BLK
VSSA
Figure 104. Power Supply Input for AD973x Evaluation Board, Rev. F
Rev. A | Page 57 of 72
04862–102
L6
33DIG
TB1 1
Rev. A | Page 58 of 72
Figure 105. Circuitry Local to AD973x, Evaluation Board, Rev. F
ACASE
04862-103
VSSA
6.3V
4.7μF
C11
VDDC
C13
C12
1nF CC0603
0.1μF CC0603
CLKN
CLKP
DNP
CC063
C5
A7
B7
C7
D7
A4
A5
A6
B4
B5
B6
C4
C5
C6
D4
D5
D6
A1
A2
A3
B1
B2
B3
C1
C2
C3
D2
D3
D1
E1
F1
E2
E3
E4
F2
F3
F4
G1
G2
G3
G4
HYDROGEN
TOP
IP1
IN1
IP2
IN2
AD9736
IP3
IN3
IP4
IN4
VSSA331
VSSA3313
VSSA332
VSSA3314
VSSA333
VSSA3315
VSSA334
VSSA3316
VSSA335
VSSA3317
VSSA336
VSSA3318
VSSA337
VSSA3319
VSSA338
VSSA3320
VSSA339
VSSA3321
VSSA3310 VSSA3322
VSSA3311 VSSA3323
VSSA3312 VSSA3324
VDDA331
VDDC1
VDDA332
VDDC2
VDDA333
VDDC3
VDDA334
VDDC4
VDDA335
VDDC5
VDDA336
VDDC6
VDDA337
VDDC7
VDDA338
VDDC8
SPARE
VDDC9
I120
VDDC10
VDDC11
VREF
VSSC1
IPTAT
CLKN
SIGNED_IRQ
CLKP
PD_RESET
VSSC2
2X_CSB
VSSC3
FIFO_SDIO
VSSC4
FSC0_SCLK
VSSC5
FSC1_SDO
VSSC6
SHIELD1
VSSC7
SHIELD2
VSSC8
SHIELD3
VSSC9
SHIELD4
VSSC10
SHIELD5
VSSC11 U1 SHIELD6
CC060
C4
1nF
C3
0.1μF
R5
10kΩ
SPCSB
SPSDI
SPCLK
SPSDO
4
3
TP16
WHT
SPARE
VSS
VSS;5
SW1
RESET
JP3
VSS
ACASE
1
2
C9
1nF
VSSA
R1
0.1%
10kΩ
VSSA
VDD33
CC0603
C24
0.1μF
VDD33
VSS
ACASE
VDD33
C21
1nF
DB13N
DB13P
DB12N
DB12P
DB11N
DB11P
DB10N
DB10P
DB9N
DB9P
DB8N
DB8P
DCLKNOUT
DCLKPOUT
JP15
CC0603
DNP
CC0603
C7
C25
1nF
3
A B
2
1 JP8 3
A B
2
1
C20
0.1μF
CC0603
H1
H2
H3
H4
J1
J2
J3
J4
K3
K4
L3
L4
L5
L6
M3
M4
M5
M6
K2
K1
L2
L1
M2
M1
N1
P1
N2
P2
N3
P3
N4
P4
N5
P5
N6
P6
L7
M7
N7
P7
HYDROGEN
VDD16
VDD1
U1
VDD15
VDD2
AD9736
VDD14
VDD3
VDD13
VDD4
VDD12
VDD5
VDD11
VDD6
VDD10
VDD7
VDD9
VDD8
VSS20
VSS1
VSS19
VSS2
VSS18
VSS3
VSS17
VSS4
VSS16
VSS5
VSS15
VSS6
VSS14
VSS7
VSS13
VSS8
VSS12
VSS9
VSS11
VSS10
VSS21
LVDS13N
NCK1
LVDS13P
VSS22
LVDS12N
SPI_MODE
LVDS12P
LVDS0N
LVDS11N
LVDS0P
LVDS11P
LVDS1N
LVDS10N
LVDS1P
LVDS10P
LVDS2N
LVDS9N
LVDS2P
LVDS9P
LVDS3N
LVDS8N
LVDS3P
LVDS8P
LVDS4N
LVDS7N
LVDS4P
LVDS7P
LVDS5N
LVDS6N
LVDS5P
LVDS6P
LVDSCLKOUTN LVDSCLKINN
LVDSCLKOUTP LVDSCLKINP
VDD331
VDD338
VDD332
VDD337
VDD333
VDD336
VDD334
VDD335
BOTTOM
H14
H13
H12
H11
J14
J13
J12
J11
K11
K12
L9
L10
L11
L12
M9
M10
M11
M12
K13
K14
L13
L14
M13
M14
N14
P14
N13
P13
N12
P12
N11
P11
N10
P10
N9
P9
L8
M8
N8
P8
NOTE: AD9736 MSB –LSB BIT ORDER IS REVERSED
FROM THE CONNECTOR BIT ORDER.
C15 CC0603 C16 CC0603 C17
0.1μF
1nF
4.7μF
6.3V
WHT
WHT
TP8
TP10
VREF
I120
CC0603
CC0603
C19
4.7μF
6.3V
VDD18A
C23
4.7μF
6.3V
VDD33
RC0603
RESET_A
TP12
WHT
IPTAT
IRQ
JP4
C2
4.7μF
6.3V
VSS
ACASE
VDDA33
ACASE
VSSA
VDD18B
IRQ
TP2
C6
WHT
CC0603
R16
10kΩ
DNP
CC0603
VSSA
A8
B8
C8
D8
A9
A10
A11
B9
B10
B11
C9
C10
C11
D9
D10
D11
A12
A13
B12
B13
C12
C13
D12
D13
A14
B14
C14
D14
E13
E14
F13
F14
G13
G14
E11
E12
F11
F12
G11
G12
IN
IP
VSS
DNP
CC0603
C34
DB0N
DB0P
DB1N
DB1P
DB2N
DB2P
DB3N
DB3P
DB4N
DB4P
DB5N
DB5P
DB6N
DB6P
DB7N
DB7P
DCLKNIN
DCLKPIN
CC0603
C8
DNP
AD9734/AD9735/AD9736
RC1206
Rev. A | Page 59 of 72
Figure 106. High Speed Digital I/O Connector, AD973x Evaluation Board, Rev. F
DB0
DB13
DB13
DB0
04862–104
AD9736
CONNECTOR
NOTE: AD9736 MSB-LSB BIT ORDER IS REVERSED
FROM THE CONNECTOR BIT ORDER.
EXTCLK
TESTOUTP
TP15
WHT
JACK
TESTOUTN
G1
S1
G3
S3
G5
S5
G7
S7
G9
S9
G11
S11
G13
S13
G15
S15
G17
S17
G19
S19
G21
S21
G23
S23
G25
S25
G27
S27
G29
S29
G31
S31
G33
S33
G35
S35
G37
S37
G39
S39
G41
S41
G43
S43
G45
S45
G47
S47
G49
G2
S2
G4
S4
G6
S6
G8
S8
G10
S10
G12
S12
G14
S14
G16
S16
G18
S18
G20
S20
G22
S22
G24
S24
G26
S26
G28
S28
G30
S30
G32
S32
G34
S34
G36
S36
G38
S38
G40
S40
G42
S42
G44
S44
G46
S46
G48
S48
G50
JACK
FCN–268 F024–G/0 D
J3
VSS
DB0P
DB1P
DB2P
DB3P
DB4P
DB5P
DB6P
DB7P
DCLKPIN
DCLKPOUT
DB8P
DB9P
DB10P
DB11P
DB12P
DB13P
DB13N
DB12N
DB11N
DB10N
DB9N
DB8N
DCLKNOUT
DCLKNIN
DB7N
DB6N
DB5N
DB4N
DB3N
DB2N
DB1N
DB0N
AD9734/AD9735/AD9736
Rev. A | Page 60 of 72
Figure 107. Clock Input and Analog Output, AD973x Evaluation Board, Rev. F
04862–105
VSSA
IP
IN
R7
DNP
RC0603
RC0603
VSSA
RC0603
RC0603
RC0603
R19
20Ω
R17
20Ω
RC0603
R18
DNP
RC0603
R17 AND R19 PRESENT A
MORE REAL LOAD TO THE
DAC WHICH IMPROVES
H2 PERFORMANCE.
R8
50Ω
R6
50Ω
RC0603
VSSA
J1
VSSA;3,4,5
SMA200UP
R162
0Ω
R161
0Ω
S
T3
NC=2
S
P
P
5
4
3
2
1
P
T3B
T3:M/A-COM
–1dB: 4.5-1000MHz
S
P
NC=2
S
S
P
P
T4B
NC=2
S
T1
5
4
3
2
1
ETC1–1–13
4
5
6
1
1
0.1μF
0.1μF
VSSA
415mV COMMON
MODE VOLTAGE
400mV p–p
C36
C35
C28
C29
DNP
1nF
C38
1nF
CC0603
VSSA
VDDC
CLKN
CLKP
AN LVDS SIGNAL MAY BE USED
TO DRIVE C35 AND C36 IF R20 AND R21
ARE INCREASED TO 50Ω EACH.
0.1μF
C27
CC0603
CC0603
DNP
VSSA
VSSA;3,4,5
SMA200UP
J2
C26
CC0603
CC0603
300Ω
R4
1kΩ
R3
RC0603
R17 AND R19 CAN BE REMOVED AND T1
REPLACED WITH A 1:1 TRANSFORMER FOR
HIGHER OUTPUT AMPLITUDE IF MORE H2
IS ACCEPTABLE (TYPICALLY AT LOWER FOUT).
T1:MINI-CIRCUITS
–3dB: 8-600MHz
–1dB: 13-300MHz
5
ADT2–1T–1P
3
6
4
ETC1–1–13
4
3
1
3
VSSA
T2 AND T4B ARE NOT POPULATED
ETC1–1–13
1
3
4
5
6
T2
ADT2–1T–1P
T3A
ADTL1–12XX
CC0603 CC0603
RC0603
R21 25Ω
RC0603
T3A IS NOT POPULATED
THIS CONFIGURATION PROVIDES OPTIMUM AC
PERFORMANCE FOR IF SIGNAL GENERATION.
TYPICAL SIGNAL LEVELS SHOWN FOR 50Ω LOAD.
JUMPER ADDED FROM T1 PIN 3 TO
T1 PIN 2 ON THE REV. C EVAL BOARD.
NOTE:
T1, T3, AND T3B ARE INSTALLED,
R6 AND R8 = 50Ω,
R7 = DNP
R17 AND R19 = 20Ω,
R161 AND R162 = 0Ω,
RC0603
R20 25Ω
AD9734/AD9735/AD9736
Rev. A | Page 61 of 72
Figure 108. SPI Port Interface, AD973x Evaluation Board, Rev. F
04862–106
VDD33
VDD33
1
1
1
A B
2
JP10
A B
2
JP9
A B
2
JP14
A B
2
JP13
VSS
IRQ
1 JP12 3
A B
2
VSS
VSS
RC0603
VSS
R13
10kΩ
JP5
VSS
JP6
VSS
VSS
JP7
JP2
3
3
3
3
RESET_A
1 JP11 3
A B
2
SPSDO
VDD33
SPSDI
VDD33
SPCLK
VDD33
SPCSB
1
RC0603
VDD33
R14
10kΩ
2
VSS;7
VDD33;14
5
VSS;7
VDD33;14
3
VSS;7
VDD33;14
1
74AC14
6
74AC14
4
74AC14
1
2
4
6
13
74AC14
8
R10
11
R11
12
10
8
FERRITE
74AC14
U6
74AC14
FERRITE
RC0805
9kΩ
RC0805
9kΩ
RC0805
9kΩ
2
6.3V
+ C30
ACASE 4.7μF
VDD33
R12
VSS;7
VDD33;14
9
VSS;7
VDD33;14
U6
LC1210
L9
13
VSS;7
VDD33;14
74AC14
LC1210
L8
VSS;7
VDD33;14
9
VSS;7
VDD33;14
11
U5
U5
U6
10
74AC14
U5
FERRITE BEAD CORE:
PANASONIC EXC-CL3225U1
DIGIKEY PN: P9811CT-ND
VSS
74AC14
U6
74AC14
U6
12
74AC14
VSS;7
VDD33;14
VSS;7
VDD33;14
5
VSS;7
VDD33;14
3
VSS;7
VDD33;14
74AC14
U6
U5
U5
U5
SPI PORT
USE THESE JUMPERS TO SET PIN_MODE
CONTROL SIGNALS OR CONNECT SPI PORT
SIGNALS IN SPI_MODE.
CC0805
C31
0.1μF
+ C32
P1
6.3V
ACASE 4.7μF
2
1
2
3
4
5
6
CC0805
C33
0.1μF
AD9734/AD9735/AD9736
AD9734/AD9735/AD9736
04862-107
NOTE:
THE AD9736 IS
SOLDERED DIRECTLY
TO THE PCB. THE
SOCKET IS NOT INSTALLED.
SILKSCREEN ERROR:
SPI AND PIN ARE REVERSED.
AD973X EVALUATION BOARD PCB LAYOUT
Figure 109. CB Layout Top Placement, AD973x Evaluation Board, Rev. F
Rev. A | Page 62 of 72
04860-108
AD9734/AD9735/AD9736
Figure 110. PCB Layout Layer 1, AD973x Evaluation Board, Rev. F
Rev. A | Page 63 of 72
04861-109
AD9734/AD9735/AD9736
Figure 111. PCB Layout Layer 2, AD973x Evaluation Board, Rev. F
Rev. A | Page 64 of 72
04862-110
AD9734/AD9735/AD9736
Figure 112. PCB Layout Layer 3, AD973x Evaluation Board, Rev. F
Rev. A | Page 65 of 72
014862-111
AD9734/AD9735/AD9736
Figure 113. PCB Layout Layer 4, AD973x Evaluation Board, Rev. F
Rev. A | Page 66 of 72
04862-112
AD9734/AD9735/AD9736
Figure 114. PCB Layout Bottom Placement, AD973x Evaluation Board, Rev. F
Rev. A | Page 67 of 72
04862-113
4. WARP AND TWIST +/– .005 INCH PER INCH.
5. DIMENTIONS: ARE FOR THE FINISHED PART
6. SOLDER MASK: LIQUID PHOTO IMAGABLE SOLDER MASK
COLOR GREEN, BOTH
SIDES USING THE PATTERN(S) PROVIDED. NO MASK
IS PERMITTED ON THE EXPOSED AREAS. SOLDER
MASK TO ETCH REGISTRATION +/– .002 INCH TOTAL
7. SCREENING: SCREEN COMPONENT OUTLINES AND
NOMENCLATURE USING OPAQUE WHITE INK ON THE
PRIMARY AND SECONDARY SIDES (AS REQUIRED).
NOMENCLATURE SHALL BE LEGIBLE. SCREEN TO ETCH
REGISTRATION +/– .005 INCH TOTAL.
8. SURFACES: PUNCHED OR MACHINED SURFACES 125 MICRO
INCHES RMS MAX.
9. BREAK ALL SHARP EDGES .015 R MAX.
10. FABRICATION VENDOR TO ADD UL VENDOR ID NUMBER
IN THIS AREA ON THE SECONDARY SIDE
11. DO NOT DRILL. FOR GOLD PLATED SOCKETED VERSION ONLY.
3. PROCESSING TOLERANCES:
A. CONDUCTIVE PATTERN FRON TO BACK REGISTRATION
+/– .002 INCH TOTAL
B. MINIMUM ANNULAR RING SURROUNDING HOLES .002 INCH.
C. FINISHED CONDUCTIVE PATTERN +/– .0005 INCH
OF APERTURE SIZE.
NOTES
1. MATERIAL: FOUR LAYER, FR4 GLASS–EPOXY LAMINATE
.062 +/- .007 THICK
1/4 OZ. COPPER CLAD – EXTERNAL LAYERS
PLATED TO 1 OUNCE
2 OZ. COPPER CLAD – INTERNAL LAYERS
2. PLATED THRU HOLES AND THE CONDUCTIVE PATTERN
ELECTROPLATED WITH .001 INCH MIN. THICK COPPER.
TERMINAL AREAS AND EXPOSED PLATED THRU HOLES TO BE
COATED WITH SOLDER AND HOT AIR LEVELED.
AD9734/AD9735/AD9736
Figure 115. PCB Fabrication Detail, AD973x Evaluation Board, Rev. F
Rev. A | Page 68 of 72
AD9734/AD9735/AD9736
OUTLINE DIMENSIONS
A1 CORNER
INDEX AREA
12.10
12.00 SQ
11.90
14
13
12
11
10
9
8
7
6
5
4
3
2
1
BALL A1
INDICATOR
10.40
BSC SQ
TOP VIEW
BOTTOM
VIEW
0.80
REF
DETAIL A
A
B
C
D
E
F
G
H
J
K
L
M
N
P
0.80 BSC
1.40 MAX
DETAIL A
1.00 MAX
0.85 MIN
0.43 MAX
0.25 MIN
0.55
0.50
0.45
BALL DIAMETER
SEATING
PLANE
0.12 MAX
COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-205-AE.
Figure 116. 160-Lead Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-160-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD9734BBC
AD9734BBCRL
AD9734BBCZ1
AD9734BBCZRL1
AD9735BBC
AD9735BBCZ1
AD9735BBCRL
AD9735BBCZRL1
AD9736BBC
AD9736BBCRL
AD9736BBCZ1
AD9736BBCZRL1
AD9734-EB
AD9735-EB
AD9736-EB
1
Z = Pb-free part.
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
160-Lead Chip Scale Package Ball Grid Array (CSP_BGA)
Evaluation Board
Evaluation Board
Evaluation Board
Rev. A | Page 69 of 72
Package Option
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
BC-160-1
AD9734/AD9735/AD9736
NOTES
Rev. A | Page 70 of 72
AD9734/AD9735/AD9736
NOTES
Rev. A | Page 71 of 72
AD9734/AD9735/AD9736
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04862-0-9/06(A)
Rev. A | Page 72 of 72