www.fairchildsemi.com KA1M0765R/KA1M0765RC Fairchild Power Switch(FPS) Features Description • • • • • • • • • The Fairchild Power Switch(FPS) product family is specially designed for an off line SMPS with minimal external components. The Fairchild Power Switch(FPS) consist of high voltage power SenseFET and current mode PWM controller IC. PWM controller features integrated fixed frequency oscillator, under voltage lock out, leading edge blanking, optimized gate turn-on/turn-off driver, thermal shutdown protection, over voltage protection, temperature compensated precision current sources for loop compensation and fault protection circuit. compared to discrete MOSFET and PWM controller or RCC solution, a Fairchild Power Switch(FPS) can reduce total component count, design size, weight and at the same time increase efficiency, productivity, and system reliability. It has a basic platform well suited for cost effective design in either a flyback converter or a forward converter. Precision fixed operating frequency (67kHz) Pulse by pulse current limiting Over load protection Over voltage protecton (Min. 23V) Internal thermal shutdown function Under voltage lockout Internal high voltage sense FET Auto restart Soft start TO-220-5L TO-3P-5L 1 1 1. DRAIN 2. GND 3. Vcc 4. FB 5. S/S Internal Block Diagram #3 VCC 32V 5V Vref Internal bias #1 DRAIN SFET Good logic #5 Soft Start OSC 5V S R − #4 FB 5µA 1mA 2.5R 1R 9V + − + 25V L.E.B 0.1V + 7.5V − Q S Thermal S/D R Q #2 GND Power on reset OVER VOLTAGE S/D Rev.1.0.2 ©2001 Fairchild Semiconductor Corporation KA1M0765R/KA1M0765RC Absolute Maximum Ratings Characteristic Symbol Value Unit VD,MAX 650 V VDGR 650 V VGS ±30 V IDM 28.0 ADC EAS 570 mJ Continuous drain current (TC=25°C) ID 7.0 ADC Continuous drain current (TC=100°C) ID 5.6 ADC VCC,MAX 30 V VFB −0.3 to VSD V PD 140 W Derating 1.11 W/°C TA −25 to +85 °C TSTG −55 to +150 °C Maximum Drain voltage (1) Drain-Gate voltage (RGS=1MΩ) Gate-source (GND) voltage Drain current pulsed (2) Single pulsed avalanche energy Maximum Supply voltage Input voltage range Total power dissipation Operating ambient temperature Storage temperature (3) Notes: 1. Tj=25°C to 150°C 2. Repetitive rating: Pulse width limited by maximum junction temperature 3. L=24mH, VDD=50V, RG=25Ω, starting Tj=25°C 2 KA1M0765R/KA1M0765RC Electrical Characteristics (SFET part) (Ta = 25°C unless otherwise specified) Characteristic Drain-source breakdown voltage Zero gate voltage drain current Static drain-source on resistance (note) Forward transconductance (note) Input capacitance Output capacitance Reverse transfer capacitance Turn on delay time Rise time Turn off delay time Fall time Symbol BVDSS IDSS RDS(ON) gfs Ciss Coss Crss td(on) tr td(off) tf Total gate charge (gate-source+gate-drain) Gate source charge Qgs Gate drain (Miller) charge Qgd Qg Test condition VGS=0V, ID=50µA VDS=Max., Rating, VGS=0V VDS=0.8Max., Rating, VGS=0V, TC=125°C VGS=10V, ID=4.0A VDS=15V, ID=4.0A VGS=0V, VDS=25V, f=1MHz VDD=0.5BVDSS, ID=7.0A (MOSFET switching time are essentially independent of operating temperature) VGS=10V, ID=7.0A, VDS=0.5BVDSS (MOSFET switching time are essentially independent of operating temperature) Min. Typ. Max. Unit 650 - - V - - 50 µA - - 200 mA 3.0 - 1.25 1600 310 120 25 55 80 1.6 - W S - 50 - - - 72 - 9.3 - - 29.3 - pF nS nC Note: Pulse test: Pulse width < 300µS, duty < 2% 1 S = ---R 3 KA1M0765R/KA1M0765RC Electrical Charcteristics (CONTROL part) (Ta = 25°C unless otherwise specified) Characteristic Symbol Test condition Min. Typ. Max. Unit After turn on 14 9 15 10 16 11 V V FOSC ∆F/∆T Dmax Ta=25°C −25°C ≤ Ta ≤ +85°C - 61 74 67 ±5 77 73 ±10 80 kHz % % IFB VSD Idelay Ta=25°C, 0V ≤Vfb ≤ 3V Ta=25°C, 5V ≤ Vfb ≤ VSD 0.7 6.9 4.0 0.9 7.5 5.0 1.1 8.1 6.0 mA V µA VFB =2V Sync & S/S=GND 4.7 0.8 5.0 1.0 5.3 1.2 V mA 4.80 - 5.00 0.3 5.20 0.6 V mV/°C 4.40 5.00 5.60 A 140 23 160 25 28 °C V UVLO SECTION Start threshold voltage Stop threshold voltage VSTART VSTOP OSCILLATOR SECTION Initial accuracy Frequency change with temperature (2) Maximum duty cycle FEEDBACK SECTION Feedback source current Shutdown Feedback voltage Shutdown delay current SOFT START SECTION Soft Start Voltage Soft Start Current VSS ISS REFERENCE SECTION Output voltage (1) Vref Ta = 25°C Vref/∆T −25°C ≤ Ta ≤ +85°C Temperature Stability (1)(2) CURRENT LIMIT (SELF-PROTECTION) SECTION Max. inductor current Peak Current Limit IOVER PROTECTION SECTION Thermal shutdown temperature (Tj) (1) Over voltage protection voltage TSD VOVP - TOTAL DEVICE SECTION Start Up current Operating supply current (control part only) VCC zener voltage ISTART VCC=14V 0.1 0.3 0.4 mA IOP Ta=25°C 6 12 18 mA VZ ICC=20mA 30 32.5 35 V Note: 1. These parameters, although guaranteed, are not 100% tested in production 2. These parameters, although guaranteed, are tested in EDS(water test) process 3.The amplitude of the sync. pulse is recommended to be between 2V and 3V for stable sync. function. 4 KA1M0765R/KA1M0765RC Typical Performance Characteristics (These characteristic graphs are normalized at Ta = 25°C) Fig.2 Feedback Source Current Fig.1 Operating Frequency 1.2 1.15 1.1 1.05 Fosc 1 0.95 0.9 0.85 0.8 -25 0 25 50 75 100 125 150 1.2 1.15 1.1 1.05 Ifb 1 IFB 0.95 0.9 0.85 0.8 -25 0 25 Temperature [°C] Figure 1. Operating Frequency Fig.3 Operating Current 1.2 1.15 1.1 1.05 lIop OP 1 0.95 0.9 0.85 0.8 -25 100 125 150 Fig.4 Max Inductor Current 1.1 1.05 IIpeak over 1 0.95 0.9 0.85 0 25 50 75 100 125 150 0.8 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 3. Operating Supply Current Figure 4. Peak Current Limit Fig.5 Start up Current Fig.6 Start Threshold Voltage 1.15 1.1 1.3 1.05 1.1 IIstart ST V th(H) 1 Vstart 0.9 0.95 0.7 0.5 -25 75 Figure 2. Feedback Source Current Temperature [°C] 1.5 50 Temperature [°C] 0.9 0 25 50 75 100 125 150 Temperature [°C] Figure 5. Start up Current 0.85 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 6. Start Threshold Voltage 5 KA1M0765R/KA1M0765RC Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25°C) Fig.7 Stop Threshold Voltage 1.15 Fig.8 Maximum Duty Cycle 1.15 1.1 1.1 1.05 1.05 Vth(L) 1 Vstop Dmax 1 0.95 0.95 0.9 0.9 0.85 -25 0 25 50 75 100 125 150 0.85 -25 0 Temperature [°C] Figure 7. Stop Threshold Voltage 50 75 100 125 150 Figure 8. Maximum Duty Cycle Fig.10 Shutdown Feedback Voltage Fig.9 Vcc Zener Voltage 1.15 1.2 1.15 1.1 1.05 Vz 1 0.95 0.9 0.85 0.8 -25 1.1 1.05 Vsd 1 0.95 0.9 0 25 50 75 100 125 150 0.85 -25 0 Temperature [°C] 50 75 100 125 150 Figure 10. Shutdown Feedback Voltage Fig.11 Shutdown Delay Current 1.2 1.15 1.1 1.05 Idelay 1 0.95 0.9 0.85 0.8 -25 25 Temperature [°C] Figure 9. VCC Zener Voltage Fig.12 Over Voltage Protection 1.15 1.1 1.05 Vovp 1 0.95 0.9 0 25 50 75 100 125 150 Temperature [°C] Figure 11. Shutdown Delay Current 6 25 Temperature [°C] 0.85 -25 0 25 50 75 100 125 150 Temperature [°C] Figure 12. Over Voltage Protection KA1M0765R/KA1M0765RC Typical Performance Characteristics (Continued) (These characteristic graphs are normalized at Ta = 25°C) Fig.13 Soft Start Voltage Fig.14 Drain Source Turn-on Resistance 1.15 2.5 1.1 2 1.05 1 1.5 0.95 ( )1 Rdson 0.9 0.5 Vss 0.85 -25 0 25 50 75 100 125 Figure13. Soft Start Voltage 150 0 -25 0 25 50 75 100 125 150 Figure 14. Static Drain-Source on Resistance 7 KA1M0765R/KA1M0765RC Package Dimensions TO-3P-5L 8 KA1M0765R/KA1M0765RC Package Dimensions (Continued) TO-3P-5L (Forming) 9 KA1M0765R/KA1M0765RC Package Dimensions (Continued) TO-220-5L 10 KA1M0765R/KA1M0765RC Package Dimensions (Continued) TO-220-5L(Forming) 11 KA1M0765R/KA1M0765RC Ordering Information Product Number KA1M0765R-TU KA1M0765R-YDTU KA1M0765RC-TU KA1M0765RC-YDTU Package TO-3P-5L TO-3P-5L(Forming) TO-220-5L TO-220-5L(Forming) Rating Fosc 650V, 7A 67kHz 650V, 7A 67kHz TU : Non Forming Type YDTU : Forming Type DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 10/17/01 0.0m 001 Stock#DSxxxxxxxx 2001 Fairchild Semiconductor Corporation