AD AD8056ARM-REEL

Low Cost, 300 MHz
Voltage Feedback Amplifiers
AD8055/AD8056
Imaging
Photodiode preamps
Video line drivers
Differential line drivers
Professional cameras
Video switchers
Special effects
A-to-D drivers
Active filters
GENERAL DESCRIPTION
The AD8055 (single) and AD8056 (dual) voltage feedback
amplifiers offer bandwidth and slew rate typically found in
current feedback amplifiers. Additionally, these amplifiers are
easy to use and available at a very low cost.
Despite their low cost, the AD8055 and AD8056 provide
excellent overall performance. For video applications, their
differential gain and phase error are 0.01% and 0.02° into a
150 Ω load and 0.02% and 0.1° while driving four video loads
(37.50 Ω).
1
8
NC
–IN
2
7
+VS
+IN
3
6
VOUT
–VS
4
5
NC
NC = NO CONNECT
1
–VS
2
+IN
3
5
+VS
4
–IN
AD8055
Figure 1. N-8 and R-8
Figure 2. RJ-5
OUT1
1
8
+VS
–IN1
2
7
OUT
+IN1
3
6
–IN2
–VS
4
5
+IN2
AD8056
01063-003
AD8055
VOUT
01063-002
NC
Figure 3. N-8, R-8, and RM-8
Their 0.1 dB flatness out to 40 MHz, wide bandwidth out to
300 MHz, along with 1400 V/μs slew rate and 20 ns settling
time, make them useful for a variety of high speed applications.
The AD8055 and AD8056 require only 5 mA typ/amplifier of
supply current and operate on a dual ±5 V or a single +12 V
power supply, while capable of delivering over 60 mA of load
current. The AD8055 is available in a small 8-lead PDIP, an 8-lead
SOIC, and a 5-lead SOT-23, while the AD8056 is available in an
8-lead MSOP. These features make the AD8055/AD8056 ideal
for portable and battery-powered applications where size and
power are critical. These amplifiers in the R-8, N-8, and RM-8
packages are available in the extended temperature range of
−40°C to +125°C.
5
4
RC
VIN
3
2
VOUT
VOUT = 100mV p-p
RL = 100Ω
50Ω
RG
RF
RL
G = +1
RF = 0Ω
RC = 100Ω
1
G = +2
RF = 402Ω
0
–1
–2
G = +10
RF = 909Ω
–3
G = +5
RF = 1000Ω
–4
–5
0.3M
1M
10M
100M
FREQUENCY (Hz)
1G
01063-004
APPLICATIONS
CONNECTION DIAGRAMS
GAIN (dB)
Low cost single (AD8055) and dual (AD8056)
Easy-to-use voltage feedback architecture
High speed
300 MHz, −3 dB bandwidth (G = +1)
1400 V/μs slew rate
20 ns settling to 0.1%
Low distortion: −72 dBc @ 10 MHz
Low noise: 6 nV/√Hz
Low dc errors: 5 mV max VOS, 1.2 μA max IB
Small packaging
AD8055 available in 5-lead SOT-23
AD8056 available in 8-lead MSOP
Excellent video specifications (RL = 150 Ω, G = +2)
Gain flatness 0.1 dB to 40 MHz
0.01% differential gain error
0.02° differential phase error
Drives 4 video loads (37.5 V) with 0.02% differential
Gain and 0.1° differential phase
Low power, ±5 V supplies 5 mA typ/amplifier power
supply current
High output drive current: over 60 mA
01063-001
FEATURES
Figure 4. Frequency Response
Rev. J
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
Powered by TCPDF (www.tcpdf.org)
IMPORTANT LINKS for the AD8055_8056*
Last content update 08/19/2013 06:20 pm
PARAMETRIC SELECTION TABLES
DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE
Find Similar Products By Operating Parameters
High Speed Amplifiers Selection Table
dBm/dBu/dBv Calculator
Analog Filter Wizard 2.0
Power Dissipation vs Die Temp
ADIsimOpAmp™
OpAmp Stability
AD8055AN SPICE Macro-Model
AD8056 SPICE Macro-Model
DOCUMENTATION
AN-649: Using the Analog Devices Active Filter Design Tool
AN-581: Biasing and Decoupling Op Amps in Single Supply
Applications
AN-402: Replacing Output Clamping Op Amps with Input Clamping
Amps
AN-417: Fast Rail-to-Rail Operational Amplifiers Ease Design
Constraints in Low Voltage High Speed Systems
MT-060: Choosing Between Voltage Feedback and Current Feedback
Op Amps
MT-059: Compensating for the Effects of Input Capacitance on VFB
and CFB Op Amps Used in Current-to-Voltage Converters
MT-058: Effects of Feedback Capacitance on VFB and CFB Op Amps
MT-056: High Speed Voltage Feedback Op Amps
MT-053: Op Amp Distortion: HD, THD, THD + N, IMD, SFDR, MTPR
MT-052: Op Amp Noise Figure: Don’t Be Mislead
MT-050: Op Amp Total Output Noise Calculations for Second-Order
System
MT-049: Op Amp Total Output Noise Calculations for Single-Pole
System
MT-048: Op Amp Noise Relationships: 1/f Noise, RMS Noise, and
Equivalent Noise Bandwidth
MT-047: Op Amp Noise
MT-033: Voltage Feedback Op Amp Gain and Bandwidth
MT-032: Ideal Voltage Feedback (VFB) Op Amp
A Stress-Free Method for Choosing High-Speed Op Amps
FOR THE AD8055
UG-127: Universal Evaluation Board for High Speed Op Amps in
SOT-23-5/SOT-23-6 Packages
UG-101: Evaluation Board User Guide
FOR THE AD8056
UG-128: Universal Evaluation Board for Dual High Speed Op Amps in
SOIC Packages
UG-129: Evaluation Board User Guide
EVALUATION KITS & SYMBOLS & FOOTPRINTS
DESIGN COLLABORATION COMMUNITY
Collaborate Online with the ADI support team and other designers
about select ADI products.
Follow us on Twitter: www.twitter.com/ADI_News
Like us on Facebook: www.facebook.com/AnalogDevicesInc
DESIGN SUPPORT
Submit your support request here:
Linear and Data Converters
Embedded Processing and DSP
Telephone our Customer Interaction Centers toll free:
Americas:
Europe:
China:
India:
Russia:
1-800-262-5643
00800-266-822-82
4006-100-006
1800-419-0108
8-800-555-45-90
Quality and Reliability
Lead(Pb)-Free Data
SAMPLE & BUY
AD8055
AD8056
View Price & Packaging
Request Evaluation Board
Request Samples
Check Inventory & Purchase
Find Local Distributors
View the Evaluation Boards and Kits page for the AD8055
View the Evaluation Boards and Kits page for the AD8056
Symbols and Footprints for the AD8055
Symbols and Footprints for the AD8056
* This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet.
Note: Dynamic changes to the content on this page (labeled 'Important Links') does not
constitute a change to the revision number of the product data sheet.
This content may be frequently modified.
AD8055/AD8056
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications..................................................................................... 12
Applications....................................................................................... 1
Four-Line Video Driver............................................................. 12
General Description ......................................................................... 1
Single-Ended-to-Differential Line Driver............................... 12
Connection Diagrams...................................................................... 1
Low Noise, Low Power Preamp................................................ 12
Revision History ............................................................................... 2
Power Dissipation Limits .......................................................... 13
Specifications..................................................................................... 3
Resistor Selection ....................................................................... 13
Absolute Maximum Ratings............................................................ 5
Driving Capacitive Loads.......................................................... 13
Maximum Power Dissipation ..................................................... 5
Outline Dimensions ....................................................................... 14
ESD Caution.................................................................................. 5
Ordering Guide .......................................................................... 16
Typical Performance Characteristics ............................................. 6
Test Circuits..................................................................................... 11
REVISION HISTORY
2/06—Rev. I to Rev. J
Changes to Format .............................................................Universal
Updated Outline Dimensions ....................................................... 15
Changes to Ordering Guide .......................................................... 16
2/04—Rev. H to Rev. I
Changes to Features.......................................................................... 1
Changes to Ordering Guide ............................................................ 3
6/03—Rev. G to Rev. H
Changes to Absolute Maximum Ratings ....................................... 3
Updated Ordering Guide................................................................. 3
Updated Outline Dimensions ....................................................... 11
2/03—Rev. F to Rev. G
Changes to Product Description .................................................... 1
Changes to Specifications ................................................................ 2
Change to Ordering Guide.............................................................. 3
Outline Dimensions Updated ....................................................... 11
10/02—Rev. E to Rev. F
Text Changes to Reflect Extended Temperature Range for
R-8, N-8 Packages..............................................................................1
Changes to Specifications.................................................................2
Changes to Absolute Maximum Ratings........................................3
Figure 2 Replaced ..............................................................................3
Changes to Ordering Guide .............................................................3
Outline Dimensions Updated....................................................... 11
7/01—Rev. D to Rev. E
TPC 24 Replaced with New Graph .................................................7
3/01—Rev. C to Rev. D
Edit to Curve in TPC 23 ...................................................................7
2/01—Rev. B to Rev. C
Edits to Text at Top of Specifications Page (65 to 5)....................2
Rev. J | Page 2 of 16
AD8055/AD8056
SPECIFICATIONS
TA = 25°C, VS = ±5 V, RF = 402 Ω, RL = 100 Ω, Gain = +2, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
Rise and Fall Time, 10% to 90%
NOISE/HARMONIC PERFORMANCE
Total Harmonic Distortion
Crosstalk, Output-to-Output (AD8056)
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
AD8055A/AD8056A
Min
Typ
Max
Conditions
G = +1, VO = 0.1 V p-p
G=+1, VO = 2 V p-p
G=+2, VO = 0.1 V p-p
G=+2, VO = 2 V p-p
VO = 100 mV p-p
G = +1, VO = 4 V step
G = +2, VO = 4 V step
G = +2, VO = 2 V step
G = +1, VO = 0.5 V step
G = +1, VO = 4 V step
G = +2, VO = 0.5 V step
G = +2, VO = 4 V step
220
125
120
125
25
1000
750
fC = 10 MHz, VO = 2 V p-p, RL = 1 kΩ
fC = 20 MHz, VO = 2 V p-p, RL = 1 kΩ
f = 5 MHz, G = +2
f = 100 kHz
f = 100 kHz
NTSC, G = +2, RL = 150 Ω
NTSC, G = +2, RL = 37.5 Ω
NTSC, G = +2, RL = 150 Ω
NTSC, G = +2, RL = 37.5 Ω
DC PERFORMANCE
Input Offset Voltage
300
150
160
150
40
1400
840
20
2
2.7
2.8
4
MHz
MHz
MHz
MHz
MHz
V/μs
V/μs
ns
ns
ns
ns
ns
−72
−57
−60
6
1
0.01
0.02
0.02
0.1
dBc
dBc
dB
nV/√Hz
pA/√Hz
%
%
Degree
Degree
3
5
10
0.4
1.2
TMIN to TMAX
Offset Drift
Input Bias Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current 1
Short-Circuit Current1
6
TMIN to TMAX
VO = ±2.5 V
TMIN to TMAX
1
66
64
VCM = ±2.5 V
RL = 150 Ω
VO = ±2.0 V
2.9
55
Rev. J | Page 3 of 16
Unit
71
mV
mV
μV/°C
μA
μA
dB
dB
10
2
3.2
82
MΩ
pF
±V
dB
3.1
60
110
±V
mA
mA
AD8055/AD8056
Parameter
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
1
AD8055A/AD8056A
Min
Typ
Max
Conditions
±4.0
AD8055
TMIN to 125°C
TMIN to 85°C
AD8056
TMIN to 125°C
TMIN to 85°C
+VS = +5 V to +6 V, −VS = −5 V
−VS = –5 V to −6 V, +VS = +5 V
AD8055ART
AD8055AR, AD8055AN, AD8056AR, AD8056AN, AD8056ARM
Output current is limited by the maximum power dissipation in the package. See Figure 5.
Rev. J | Page 4 of 16
±5.0
5.4
7.6
10
13.9
±6.0
6.5
7.3
12
13.3
66
69
−40
−40
72
86
+85
+125
Unit
V
mA
mA
mA
mA
mA
mA
dB
dB
°C
°C
AD8055/AD8056
ABSOLUTE MAXIMUM RATINGS
Table 2.
Storage Temperature Range N, R
Operating Temperature Range (A Grade)
Lead Temperature (Soldering 10 sec)
MAXIMUM POWER DISSIPATION
Ratings
13.2 V
±VS
±2.5 V
Observe Power
Derating Curves
−65°C to +150°C
−40°C to +125°C
300°C
While the AD8055/AD8056 are internally short-circuit
protected, this may not be sufficient to guarantee that the
maximum junction temperature (150°C) is not exceeded under
all conditions. To ensure proper operation, it is necessary to
observe the maximum power derating curves.
2.5
MAXIMUM POWER DISSIPATION (W)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
The maximum power that can be safely dissipated by the
AD8055/AD8056 is limited by the associated rise in junction
temperature. The maximum safe junction temperature for
plastic encapsulated devices is determined by the glass
transition temperature of the plastic, approximately 150°C.
Exceeding this limit temporarily can cause a shift in parametric
performance due to a change in the stresses exerted on the die
by the package. Exceeding a junction temperature of 175°C for
an extended period can result in device failure.
2.0
PDIP-8
SOIC-8
1.5
1.0
MSOP-8
0.5
SOT-23-5
0
–55 –45 –35 –25 –15 –5
5
15 25 35 45 55 65 75 85 95 105 115 125
AMBIENT TEMPERATURE (°C)
Figure 5. Plot of Maximum Power Dissipation vs.
Temperature for AD8055/AD8056
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. J | Page 5 of 16
01063-005
Parameter
Supply Voltage
Input Voltage (Common Mode)
Differential Input Voltage
Output Short-Circuit Duration
AD8055/AD8056
TYPICAL PERFORMANCE CHARACTERISTICS
0V
5ns
1V
Figure 6. Small Step Response, G = +1 (See Figure 34)
01063-011
20mV
01063-007
0V
5ns
Figure 9. Large Step Response, G = −1 (See Figure 35)
5
4
3
RG
01063-008
Figure 7. Large Step Response, G = +1 (See Figure 34)
RF
RL
G = +1
RF = 0Ω
RC = 100Ω
G = +2
RF = 402Ω
1
0
–1
G = +10
RF = 909Ω
–3
5ns
VOUT = 100mV p-p
RL = 100Ω
50Ω
–2
1V
VOUT
G = +5
RF = 1000Ω
–4
–5
0.3M
1M
10M
100M
FREQUENCY (Hz)
1G
01063-012
GAIN (dB)
2
0V
RC
VIN
Figure 10. Small Signal Frequency Response, G = +1, G = +2, G = +5, G = +10
5
VOUT = 2V p-p
RL = 100Ω
4
3
0V
G = +1
RF = 0Ω
1
0
G = +2
RF = 402Ω
–1
–2
G = +10
RF = 909Ω
20mV
5ns
Figure 8. Small Step Response, G = −1 (See Figure 35)
01063-010
–3
G = +5
RF = 1000Ω
–4
–5
0.3M
1M
10M
100M
FREQUENCY (Hz)
1G
01063-013
GAIN (dB)
2
Figure 11. Large Signal Frequency Response, G = +1, G = +2, G = +5, G = +10
Rev. J | Page 6 of 16
AD8055/AD8056
–40
0.5
VOUT = 100mV
G = +2
RL = 100Ω
RF = 402Ω
0.4
0.3
DISTORTION (dBc)
0.2
OUTPUT (dB)
G = +2
RL = 1kΩ
–50
0.1
0
–0.1
–0.2
–0.3
–60
SECOND
–70
THIRD
–80
1M
10M
100M
FREQUENCY (Hz)
1G
–90
01063-014
–0.5
0.3M
0
0.4
Figure 12. 0.1 dB Flatness
1.6 2.0
2.4
VOUT (V p-p)
3.2
3.6
4.0
4.5
5.0
4.5
5.0
G = +1
RL = 100Ω
RF = 0Ω
9
–80
THIRD
–90
8
7
6
5
FALL TIME
4
3
2
RISE TIME
100k
1M
FREQUENCY (Hz)
10M
100M
01063-015
1
0
0
Figure 13. Harmonic Distortion vs. Frequency
0.5
1.0
1.5
2.0 2.5 3.0
VIN (V p-p)
3.5
4.0
01063-018
SECOND
–70
–100
10k
2.8
10
VOUT = 2V p-p
G = +2
RL = 100Ω
RISE TIME AND FALL TIME (ns)
HARMONIC DISTORTION (dBc)
1.2
Figure 15. Distortion vs. VOUT @ 20 MHz
–50
–60
0.8
01063-017
–0.4
Figure 16. Rise Time and Fall Time vs. VIN
10
–70
–80
SECOND
8
7
6
5
4
FALL TIME
3
2
–90
0
100k
1M
FREQUENCY (Hz)
10M
100M
01063-016
–100
10k
RISE TIME
1
THIRD
0
0.5
1.0
1.5
2.0 2.5 3.0
VIN (V p-p)
3.5
4.0
Figure 17. Rise Time and Fall Time vs. VIN
Figure 14. Harmonic Distortion vs. Frequency
Rev. J | Page 7 of 16
01063-019
–60
G = +1
RL = 1kΩ
RF = 0Ω
9
VOUT = 2V p-p
G = +2
RL = 1kΩ
RISE TIME AND FALL TIME (ns)
HARMONIC DISTORTION (dBc)
–50
AD8055/AD8056
0.7
10
VOUT = 0V TO +2V OR
VOUT = 0V TO –2V
G = +2
RL = 100Ω
0.6
0.5
G = +2
RF = 402Ω
0
–10
0.4
–20
PSRR (dB)
0.2
0.1
0
–0.1
–PSRR
–40
–50
+PSRR
–60
–0.2
–70
–0.3
–80
–0.4
0
10
20
30
TIME (ns)
40
50
60
–90
0.1
01063-020
–0.5
–30
1
Figure 18. Settling Time
10
FREQUENCY (MHz)
100
500
01063-023
ERROR (%)
0.3
Figure 21. PSRR vs. Frequency
10
G = +2
RL = 100Ω
RF = 402Ω
VIN
G = +1
RL = 100Ω
VS = ±5V
8
VOUT
7
6
5
4
RISE TIME
3
FALL TIME
1
0
0
0.2
0.4
0.6
0.8
1.0
VIN (V p-p)
1V
1.2
1.4
1.6
01063-024
2
50ns
01063-021
RISE TIME AND FALL TIME (ns)
9
Figure 19. Rise Time and Fall Time vs. VIN
Figure 22. Overload Recovery
5.0
G = +2
RL = 1kΩ
RF = 402Ω
4.0
–20
–40
3.5
CROSSTALK (dB)
RISE TIME
3.0
2.5
2.0
FALL TIME
1.5
1.0
–50
–60
SIDE 2 DRIVEN
–70
–80
SIDE 1 DRIVEN
–90
–100
0.5
–110
0
0.2
0.4
0.6
0.8
1.0
VIN (V p-p)
1.2
1.4
1.6
–120
0.1
1
10
FREQUENCY (MHz)
100 200
Figure 20. Rise Time and Fall Time vs. VIN
Figure 23. Crosstalk (Output-to-Output) vs. Frequency
Rev. J | Page 8 of 16
01063-025
0
VIN = 0dBm
G = +2
RL = 100Ω
RF = 402Ω
–30
01063-022
RISE TIME AND FALL TIME (ns)
4.5
AD8055/AD8056
0
180
–20
50Ω
402Ω
135
58Ω
402Ω
PHASE (Degrees)
–30
CMRR (dB)
402Ω
402Ω
–10
–40
–50
–60
90
45
–70
0
–80
–45
100
500
–90
10k
100k
Figure 24. CMRR vs. Frequency
DIFFERENTIAL GAIN (%)
VIN (1V/DIV)
DIFFERENTIAL PHASE
(Degrees)
VOUT (2V/DIV)
50ns
0.04
0
50
40
DIFFERENTIAL PHASE
(Degrees)
30
20
10
0
0.1
1
10
FREQUENCY (MHz)
100
500
01063-028
OPEN-LOOP GAIN (dB)
DIFFERENTIAL GAIN (%)
RL = 100Ω
60
–10
0.01
G = +2
RF = 402Ω
–0.02
–0.04
1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH
IRE
0.04
1 BACK TERMINATED LOAD (150Ω)
0.02
0
G = +2
RF = 402Ω
–0.02
–0.04
1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH
IRE
Figure 28. Differential Gain and Differential Phase
90
70
500M
1 BACK TERMINATED LOAD (150Ω)
0.02
Figure 25. Overload Recovery
80
100M
Figure 27. Phase vs. Frequency
01063-027
G = +2
RL = 100Ω
RF = 402Ω
VS = ±5V
1M
10M
FREQUENCY (Hz)
01063-030
10
FREQUENCY (MHz)
0.04
4 VIDEO LOADS (37.5Ω)
0.02
0
G = +2
RF = 402Ω
–0.02
–0.04
1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH
IRE
0.15
4 VIDEO LOADS (37.5Ω)
0.10
0.05
0
–0.05
–0.10
–0.15
G = +2
RF = 402Ω
1ST 2ND 3RD 4TH 5TH 6TH 7TH 8TH 9TH 10TH 11TH
IRE
Figure 29. Differential Gain and Differential Phase
Figure 26. Open-Loop Gain vs. Frequency
Rev. J | Page 9 of 16
01063-031
1
01063-026
–100
0.1
01063-029
–90
AD8055/AD8056
5.0
100
VS = ±5V
4.0
RL = 1kΩ
3.5
±VOUT (V)
CURRENT NOISE (pA/ Hz)
4.5
3.0
2.5
RL = 150Ω
2.0
RL = 50Ω
1.5
10
1
1.0
–35
–15
5
25
45
65
TEMPERATURE (°C)
85
105
125
0.1
10
01063-032
0
–55
100
Figure 30. Output Swing vs. Temperature
10k
100k
FREQUENCY (Hz)
1M
10M
50M
Figure 32. Current Noise vs. Frequency
1000
45
40
G = +2
RF = 402Ω
35
30
|ZOUT| (Ω)
100
10
6nV/ Hz
25
20
15
10
5
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
50M
–5
0.01
Figure 31. Voltage Noise vs. Frequency
0.1
1
10
FREQUENCY (MHz)
100
Figure 33. Output Impedance vs. Frequency
Rev. J | Page 10 of 16
500
01063-035
0
1
10
01063-033
VOLTAGE NOISE (nV/ Hz)
1k
01063-034
0.5
AD8055/AD8056
TEST CIRCUITS
402Ω
4.7µF
0.01µF
+VS
0.001µF
VIN
100Ω
3
7
AD8055
50Ω
2
4
0.01µF
0.001µF
VOUT
HP8130A
PULSE
GENERATOR
TR/TF = 0.67ns
6
100Ω
4.7µF
0.01µF
0.001µF
–VS
VIN 402Ω
2
7
AD8055
57Ω
3
4
6
VOUT
0.001µF
–VS
Figure 35. G = −1, RL = 100 Ω
Figure 34. G = +1, RL = 100 Ω
Rev. J | Page 11 of 16
100Ω
4.7µF
0.01µF
01063-006
HP8130A
PULSE
GENERATOR
TR/TF = 1ns
4.7µF
01063-009
+VS
AD8055/AD8056
APPLICATIONS
FOUR-LINE VIDEO DRIVER
Between these points, a feedback resistor can be used to close
the loop. As in the case of a conventional op amp inverting gain
stage, an input resistor is added to vary the gain.
The AD8055 is a useful low cost circuit for driving up to four
video lines. For such an application, the amplifier is configured
for a noninverting gain of 2, as shown in Figure 36. The input
video source is terminated in 75 Ω and is applied to the high
impedance noninverting input.
Each output cable is connected to the op amp output via a 75 Ω
series back termination resistor for proper cable termination.
The terminating resistors at the other ends of the lines divide
the output signal by 2, which is compensated for by the gain of 2
of the op amp stage.
For a single load, the differential gain error of this circuit was
measured as 0.01%, with a differential phase error of 0.02°. The
two load measurements were 0.02% and 0.03°, respectively. For
four loads, the differential gain error is 0.02%, while the
differential phase increases to 0.1°.
The gain of this circuit from the input to AMP1 output is RF/RI,
while the gain to the output of AMP2 is −RF /RI. The circuit
therefore creates a balanced differential output signal from a
single-ended input. The advantage of this circuit is that the gain
can be changed by changing a single resistor, while still
maintaining the balanced differential outputs.
RF
402Ω
+5V
VIN
0.1µF
RI
402Ω
3
10µF
8
49.9Ω
AMP1
1
+VOUT
2
402Ω
75Ω
VOUT1
+5V
75Ω
402Ω
7
3
75Ω
402Ω
402Ω
VOUT2
75Ω
6
6
4
75Ω
0.1µF
–5V
10µF
49.9Ω
AMP2
VOUT3
5
75Ω
7
75Ω
0.1µF
75Ω
–VOUT
4
VOUT4
75Ω
Figure 36. Four-Line Video Driver
10µF
01063-037
AD8055
VIN
75Ω
–5V
Figure 37. Single-Ended-to-Differential Line Driver
LOW NOISE, LOW POWER PREAMP
SINGLE-ENDED-TO-DIFFERENTIAL LINE DRIVER
Creating differential signals from single-ended signals is
required for driving balanced, twisted pair cables, differential
input ADCs, and other applications that require differential
signals. This can be accomplished by using an inverting and a
noninverting amplifier stage to create the complementary
signals.
The circuit shown in Figure 37 shows how an AD8056 can be
used to make a single-ended-to-differential converter that offers
some advantages over the architecture previously mentioned.
Each op amp is configured for unity gain by the feedback
resistors from the outputs to the inverting inputs. In addition,
each output drives the opposite op amp with a gain of −1 by
means of the crossed resistors. The result of this is that the
outputs are complementary and there is high gain in the overall
configuration.
Feedback techniques similar to a conventional op amp are used
to control the gain of the circuit. From the noninverting input
of AMP1 to the output of AMP2 is an inverting gain.
The AD8055 makes a good, low cost, low noise, low power
preamp. A gain-of-10 preamp can be made with a feedback
resistor of 909 Ω and a gain resistor of 100 Ω, as shown in
Figure 38. The circuit has a −3 dB bandwidth of 20 MHz.
909Ω
+5V
100Ω
0.1µF
2
7
AD8055
3
+
10µF
VOUT
6
4
RS
0.1µF
–5V
10µF
01063-038
2
10µF
01063-036
402Ω
0.1µF
402Ω
AD8056
Figure 38. Low Noise, Low Power Preamp with G = +10 and BW = 20 MHz
With a low source resistance (< approximately 100 Ω), the
major contributors to the input-referred noise of this circuit are
the input voltage noise of the amplifier and the noise of the
100 Ω resistor. These are 6 nV/√Hz and 1.2 nV/√Hz, respectively.
These values yield a total input referred noise of 6.1 nV/√Hz.
Rev. J | Page 12 of 16
AD8055/AD8056
5
POWER DISSIPATION LIMITS
402Ω
NORMALIZED GAIN (dB)
3
The power dissipated under heavy load conditions is
approximately equal to the supply voltage minus the output
voltage, times the load current, plus the quiescent power
previously computed. The total power dissipation is then
multiplied by the thermal resistance of the package to find the
temperature rise, above ambient, of the part. The junction
temperature should be kept below 150°C.
VIN = 0dBm
2
CL
0
CL = 20pF
–1
CL = 10pF
–2
CL = 0pF
–3
–5
0.3
1
10
FREQUENCY (MHz)
In general, to minimize peaking or to ensure the stability for
larger values of capacitive loads, a small series resistor, RS, can
be added between the op amp output and the capacitor, CL. For
the setup depicted in Figure 40, the relationship between RS and
CL was empirically derived and is shown in Figure 41. RS was
chosen to produce less than 1 dB of peaking in the frequency
response. Note also that after a sharp rise, RS quickly settles to
approximately 25 Ω.
402Ω
+5V
0.1µF
AD8055
402
249
100
FET PROBE
VOUT
RS
6
CL
4
3
50Ω
−3 dB Bandwidth (MHz)
300
160
45
20
10µF
7
2
VIN = 0dBm
RG (Ω)
500
Figure 39. Capacitive Load Drive
Table 3 is a guide for resistor selection for maintaining gain
flatness vs. frequency for various values of gain.
RF (Ω)
0
402
1k
909
100
01063-039
–4
402Ω
Table 3.
CL = 30pF
100Ω
1
RESISTOR SELECTION
Gain
+1
+2
+5
+10
50Ω
0.1µF
10µF
01063-040
The AD8055 in the SOT-23-5 package can dissipate 270 mW,
while the AD8056 in the MSOP-8 package can dissipate
325 mW (at 85°C ambient) without exceeding the maximum
die temperature. In the case of the AD8056, this is greater than
1.5 V rms into 50 Ω, enough to accommodate a 4 V p-p sine
wave signal on both outputs simultaneously. However, because
each output of the AD8055 or AD8056 is capable of supplying
as much as 110 mA into a short circuit, a continuous shortcircuit condition will exceed the maximum safe junction
temperature.
402Ω
4
With a 10 V supply (total VCC − VEE), the quiescent power
dissipation of the AD8055 in the SOT-23-5 package is 65 mW,
while the quiescent power dissipation of the AD8056 in the
MSOP-8 is 120 mW. This translates into a 15.6°C rise above the
ambient for the SOT-23-5 package and a 24°C rise for the
MSOP-8 package.
–5V
Figure 40. Setup for RS vs. CL
40
35
DRIVING CAPACITIVE LOADS
30
25
RS (Ω)
When driving a capacitive load, most op amps exhibit peaking
in the frequency response just before the frequency rolls off.
Figure 39 shows the responses for an AD8056 running at a gain
of +2, with an 100 Ω load that is shunted by various values of
capacitance. It can be seen that under these conditions the part
is still stable with capacitive loads of up to 30 pF.
20
15
10
0
0
10
20
30
40
CL (pF)
Figure 41. RS vs. CL
Rev. J | Page 13 of 16
50
60
270
01063-041
5
AD8055/AD8056
OUTLINE DIMENSIONS
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
8
5
1
4
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
PIN 1
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210
(5.33)
MAX
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
COMPLIANT TO JEDEC STANDARDS MS-001-BA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 42. 8-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body (N-8)
Dimensions shown in inches and (millimeters)
5.00 (0.1968)
4.80 (0.1890)
8
4.00 (0.1574)
3.80 (0.1497) 1
5
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2440)
4 5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
0.50 (0.0196)
× 45°
0.25 (0.0099)
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 43. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
Rev. J | Page 14 of 16
AD8055/AD8056
3.20
3.00
2.80
8
3.20
3.00
2.80
5.15
4.90
4.65
5
1
4
PIN 1
0.65 BSC
0.95
0.85
0.75
1.10 MAX
0.15
0.00
0.38
0.22
COPLANARITY
0.10
0.80
0.60
0.40
8°
0°
0.23
0.08
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 44. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
2.90 BSC
5
4
2.80 BSC
1.60 BSC
1
2
3
PIN 1
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.15 MAX
0.50
0.30
0.22
0.08
SEATING
PLANE
10°
5°
0°
COMPLIANT TO JEDEC STANDARDS MO-178-AA
Figure 45. 5-Lead Small Outline Transistor Package [SOT-23]
(RJ-5)
Dimensions shown in millimeters
Rev. J | Page 15 of 16
0.60
0.45
0.30
AD8055/AD8056
ORDERING GUIDE
Model
AD8055AN
AD8055ANZ 1
AD8055AR
AD8055AR-REEL
AD8055AR-REEL7
AD8055ARZ1
AD8055ARZ-REEL1
AD8055ARZ-REEL71
AD8055ART-R2
AD8055ART-REEL
AD8055ART-REEL7
AD8055ARTZ-R21
AD8055ARTZ-REEL71
AD8056AN
AD8056ANZ1
AD8056AR
AD8056AR-REEL
AD8056AR-REEL7
AD8056ARZ1
AD8056ARZ-REEL1
AD8056ARZ-REEL71
AD8056ARM
AD8056ARM-REEL
AD8056ARM-REEL7
AD8056ARMZ1
AD8056ARMZ-REEL1
AD8056ARMZ-REEL71
1
2
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead PDIP
8-Lead PDIP
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
5-Lead SOT-23, Reel
5-Lead SOT-23, 13" Tape and Reel
5-Lead SOT-23, 7" Tape and Reel
5-Lead SOT-23, Reel
5-Lead SOT-23, 7" Tape and Reel
8-Lead PDIP
8-Lead PDIP
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
Z = Pb-free part, # denotes lead-free product may be top or bottom marked.
Prior to 0542, parts were branded H3A.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01063-0-2/06(J)
Rev. J | Page 16 of 16
Package Option
N-8
N-8
R-8
R-8
R-8
R-8
R-8
R-8
RJ-5
RJ-5
RJ-5
RJ-5
RJ-5
N-8
N-8
R-8
R-8
R-8
R-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
Branding
H3A
H3A
H3A
H3A
H07 2
H5A
H5A
H5A
H5A#
H5A#
H5A#