NEW PRODUCT NEW PRODUCT NEW PRODUCT UG10ACT THRU UG10DCT ULTRAFAST SOFT RECOVERY RECTIFIER Reverse Voltage - 200 Volts Forward Current - 10.0 Amperes FEATURES TO-220AB 0.185 (4.70) 0.415 (10.54) MAX. 0.175 (4.44) 0.370 (9.40) 0.360 (9.14) 0.154 (3.91) 0.055 (1.39) DIA. 0.148 (3.74) 0.045 (1.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) 0.350 (8.89) 0.635 (16.13) 0.330 (8.38) 0.625 (15.87) 1 PIN 2 1.148 (29.16) 3 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.160 (4.06) 0.140 (3.56) ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for free wheeling diode power factor correction applications ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Optimized to reduce switching losses ♦ High temperature soldering guaranteed: 250°C/10 seconds at terminals ♦ Glass passivated chip junction 0.560 (14.22) 0.530 (13.46) 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) 0.105 (2.67) 0.095 (2.41) MECHANICAL DATA 0.022 (0.56) 0.014 (0.35) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 2 PIN 3 CASE Case: JEDEC TO-220AB molded plastic body Terminals: Plated leads, solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs. max. Weight: 0.08 ounce, 2.24 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UG10ACT UG10BCT UG10CCT UG10DCT UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Working peak reverse voltage VRWM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward rectified current at TC=100°C I(AV) 10 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg IFSM 60 Amps Maximum instantaneous forward voltage per leg at IF=10A, IF=5A, IF=5A, TJ=25°C TJ=25°C TJ=150°C VF 1.25 1.10 0.895 Volts Maximum reverse leakage current per leg at working peak reverse voltage TJ=25°C TJ=100°C IR 10 200 µA trr 25 ns trr 25 15 ns IRM 0.7 Amps Qrr 5.5 4.5 nC RΘJC 4.5 °C/W TJ, TSTG -40 to +150 °C Maximum reverse recovery time per leg at IF=1.0A, di/dt=100A/µs, VR=30V, Irr=0.1 IRM Maximum reverse recovery time per leg at IF=0.5A, IR=1.0A, Irr=0.25A Maximum Typical Maximum reverse recovery current per leg at IF=5A, di/dt=50A/µs,VR=30V Maximum stored charge per leg IF=2A, di/dt=20A/µs, VR=30V Irr=0.1 IRM Typical thermal resistance from junction to case per leg Operating junction and storage temperature range NOTICE: Advanced product information is subject to change without notice 4/98 Maximum Typical RATINGS AND CHARACTERISTIC CURVES UG10ACT THRU UG10DCT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 15 100 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD CURRENT, AMPERES FIG. 1 -FORWARD CURRENT DERATING CURVE 10 5 0 10 1 0 25 50 75 100 125 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TC=105°C 150 1 10 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1,000 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 TJ=125°C TJ=100°C 1 TJ=25°C 0.1 TJ=125°C TJ=100°C 100 10 1 0.1 0.01 0.2 0.4 0.6 100 NUMBER OF CYCLES AT 60 HZ CASE TEMPERATURE, °C 0.8 1.0 1.2 TJ=25°C 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 1.4 FIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG 50 100 TJ=125°C f=1.0 MHz Vsig=50MVp-p @2A, 20A/µs 40 @5A, 50A/µs CAPACITANCE, pF STORED CHARGE/REVERSE RECOVERY TIME, nC/ns INSTANTANEOUS FORWARD VOLTAGE, VOLTS 30 @1A, 100A/µs 20 @5A, 50A/µs @1A, 100A/µs 10 @2A, 20A/µs 0 25 10 50 75 100 JUNCTION TEMPERATURE, °C trr Qrr 125 1 0.1 1 10 REVERSE VOLTAGE, VOLTS 100