DATA SHEET GBU6A~GBU6K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER GBU VOLTAGE - 100 Volts CURRENT - 6.0 Amperes FEATURES .310(7.90) .290(7.40) • Plastic material has Underwriters Laboratory Flammability Classification 94V-O • Ideal for printed circuit board Unit: inch ( mm ) .880(22.3) .860(21.8) .160(4.1) .140(3.5) .140(3.56) .130(3.30) .075(1.90)R .085(2.16) .065(1.65) • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension MECHANICAL DATA Case: Reliable low cost construction utilizing .100(2.54) .085(2.16) molded plastic technique Terminals: Leads solderable per MIL-STD-202, .740(18.8) .720(18.3) • Surge overload rating: 175 Amperes peak .710(18.0) .690(17.5) .080(2.03) .060(1.52) • Reliable low cost construction utilizing molded plastic technique .040(1.02) .030(0.76) .022(0.56) .018(0.46) .080(2.03) .065(1.65) Method 208 Mounting position: Any .190(4.83) .210(5.33) Mounting torque: 5 in. lb. Max. .050(1.27) .040(1.02) Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. GBU6A GBU6B GBU6D GBU6G GBU6J GBU6K UNIT Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V Maximum RMS Input Voltage 35 70 140 280 420 560 V Maximum DC Blocking Voltage 50 100 200 400 600 800 V Maximum Average Forward TC=100°C 6.0 A 127 A2sec 175 Apk Maximum Instantaneous Forward Voltage Drop per element at 3.0A 1.0 Vpk Maximum Reverse Leakage at rated TA=25° CDc Blocking Voltage per element TC=100°C 5.0 500 µA µA Typical Thermal Resistance per leg(Note 2) RθJA 8.6 °C / W Typical Thermal Resistance per leg(Note 3) RθJC 3.1 °C / W -55+150 °C Rectified Output Current at I2t Rating for fusing ( t<8.35ms) Peak Forward Surge Current single sine-wave superimposed on rated load(JEDEC method) Operating and Storage Temperature Range, TJ,TSTG NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. DATE : SEP.16.2002 PAGE . 1 INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES RATING AND CHARACTERISTIC C URVES 6.0 HEAT-SINK MOUNTING,TC (4 4 0 .15) INCH COPPER PLATE 4.0 2.0 MOUNTED ON PC BOARD. TA 0.5"(12.7mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 100 40 20 10 4.0 1.0 0.4 0.2 0 0 50 100 0.1 0.7 150 TEMPERATUREOC FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 10 O TC = 100 C 1.0 0.1 O TA= 25 C 0.01 20 40 60 80 100 120 0.8 0.9 1.0 1.1 1.2 1.3 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig . 1- DERATING C URVE FOR OUTPUT RECTIFIED CURRENT 0 O TJ= 25 C Pulse Wid th= 300 S 1% DULY Cyc le 2.0 140 PERCENT OF PEAK REVERSE VOLTAGE Fig . 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERIS ITCS PER ELEMENT 175 140 105 70 O TA= 105 C 35 0 1 2 6 10 20 40 60 100 NO. OF CYCLES AT 62Hz Fig . 3- TYPICAL REAK REVERSE CHARACTER ISTICS Fig . 4- MAXIMUM NON-REPETITEVE PEAK FORWARD SURGE CURRENT CAPACITANCE, p F 400 100 O Tj= 25 C f= 1.0MHz Vsig = 50mVp -p 50 10 1 5 10 50 100 REVERSE VOLTAGE, VOLTS Fig. 5- TYPICL J UNCTION CAPACITANCE PER ELEMENT DATE : SEP.16.2002 PAGE . 2