AD ADM1385ARS

Low Power, 3.3 V, RS-232
Line Drivers/Receivers
ADM3202/ADM3222/ADM1385
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
+3.3V INPUT
0.1µF +
10V
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
T1OUT
T2
R2
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
Figure 1.
General-purpose RS-232 data link
Portable instruments
Printers, palmtop computers, PDAs
+3.3V INPUT
0.1µF +
10V
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
T2IN
T1OUT
T2
R2
EIA/TIA-232
OUTPUTS
EIA/TIA-232
INPUTS*
R2IN
EN
C5
0.1µF
SD
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
00071-002
ADM3222
GND
Figure 2.
+3.3V INPUT
T1IN
V–
C4
0.1µF
10V
T1
T2IN
T1OUT
T2
T2OUT
R1
R1OUT
R1IN
R2
R2OUT
DD
GND
ADM1385
R2IN
C3
0.1µF
10V
C5
0.1µF
EIA/TIA-232
OUTPUTS
EIA/TIA-232
INPUTS*
SD
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
00071-003
0.1µF +
10V
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
+
CMOS
OUTPUTS
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
+
CMOS
INPUTS
0.1µF +
10V
+
The ADM3202 is available in a 16-lead PDIP, SOIC_W, and
SOIC_N, as well as a space-saving 16-lead TSSOP. The ADM3222
is available in 18-lead PDIP and SOIC_W and in 20-lead SSOP
and TSSOP. The ADM1385 is available in a 20-lead SSOP,
which is pin-compatible with the LTC1385 CG.
R1IN
R2OUT
Four external 0.1 μF charge pump capacitors are used for the
voltage doubler/inverter, permitting operation from a single
3.3 V supply.
The ADM1385 contains a driver disable mode and a complete
shutdown mode.
T2OUT
R1
R1OUT
The ADM3202/ADM3222/ADM1385 parts conform to the
EIA-232E and CCITT V.28 specifications and operate at data
rates up to 460 kbps.
C4
0.1µF
10V
V–
T1
T1IN
C3
0.1µF
6.3V
+
CMOS
OUTPUTS
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
+
CMOS
INPUTS
0.1µF +
10V
+
GENERAL DESCRIPTION
The ADM3222 contains additional enable and shutdown
circuitry. The EN input can be used to three-state the receiver
outputs. The SD input is used to power down the charge pump
and transmitter outputs, reducing the quiescent current to less
than 0.5 μA. The receivers remain enabled during shutdown
unless disabled using EN.
EIA/TIA-232
INPUTS*
R2IN
ADM3202
APPLICATIONS
The ADM3202/ADM3222/ADM1385 transceivers are high
speed, 2-channel RS-232/V.28 interface devices that operate
from a single 3.3 V power supply. Low power consumption and
a shutdown facility (ADM3222/ADM1385) make them ideal for
battery-powered portable instruments.
R1IN
R2OUT
GND
EIA/TIA-232
OUTPUTS
T2OUT
R1
R1OUT
C5
0.1µF
00071-001
T2IN
C4
0.1µF
10V
V–
T1
T1IN
C3
0.1µF
6.3V
+
CMOS
OUTPUTS
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
+
CMOS
INPUTS
0.1µF +
10V
+
460 kbps data rate
Specified at 3.3 V
Meets EIA-232E specifications
0.1 μF charge pump capacitors
Low power shutdown (ADM3222 and ADM1385)
PDIP, SOIC_N, SOIC_W, SSOP, and TSSOP options
Upgrade for MAX3222/MAX3232 and LTC1385
ESD protection to IEC 1000-4-2 (801.2)
on RS-232 pins (ADM3202 only)
±8 kV: contact discharge
±15 kV: air gap discharge
Figure 3.
Rev. E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©1998–2011 Analog Devices, Inc. All rights reserved.
ADM3202/ADM3222/ADM1385
TABLE OF CONTENTS
Features .............................................................................................. 1 Pin Configurations (N, RN, RU, and RW Packages)................5 Applications....................................................................................... 1 Pin Configurations (RS and RU Packages)................................5 General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6 Functional Block Diagrams............................................................. 1 General Description..........................................................................8 Revision History ............................................................................... 2 Circuit Description .......................................................................8 Specifications..................................................................................... 3 High Baud Rate..............................................................................9 Absolute Maximum Ratings............................................................ 4 Outline Dimensions ....................................................................... 10 ESD Caution.................................................................................. 4 Ordering Guide .......................................................................... 14 Pin Configurations and Function Descriptions ........................... 5 REVISION HISTORY
7/11—Rev. D to Rev. E
Changes to Figure 3.......................................................................... 1
Changes to Table 2............................................................................ 4
Changes to Figure 17........................................................................ 8
Updated Outline Dimensions ....................................................... 10
Changes to Ordering Guide .......................................................... 14
8/06—Rev. C to Rev. D
Changes to Table 1............................................................................ 3
Updated Outline Dimensions ....................................................... 10
Changes to Ordering Guide .......................................................... 12
9/05—Rev. B to Rev. C
Updated Outline Dimensions ....................................................... 10
Changes to Ordering Guide .......................................................... 12
12/01—Rev. A to Rev. B
Changes to Specifications Page....................................................... 2
Rev. E | Page 2 of 16
ADM3202/ADM3222/ADM1385
SPECIFICATIONS
VCC = 3.3 V ± 0.3 V, C1 to C4 = 0.1 μF. All specifications TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
DC CHARACTERISTICS
Operating Voltage Range
VCC Power Supply Current
Shutdown Supply Current
LOGIC
Input Logic Threshold Low, VINL
Input Logic Threshold High, VINH
CMOS Output Voltage Low, VOL
CMOS Output Voltage High, VOH
Logic Pull-Up Current
Output Leakage Current
RS-232 RECEIVER
EIA-232 Input Voltage Range
EIA-232 Input Threshold Low
EIA-232 Input Threshold High
EIA-232 Input Hysteresis
EIA-232 Input Resistance
RS-232 TRANSMITTER
Output Voltage Swing (RS-232)
Output Voltage Swing (RS-562)
Transmitter Output Resistance
RS-232 Output Short-Circuit Current
Output Leakage Current
TIMING CHARACTERISTICS
Maximum Data Rate
Receiver Propagation Delay
TPHL
TPLH
Transmitter Propagation Delay
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Skew
Receiver Skew
Transition Region Slew Rate
1
Min
Typ
Max
Unit
Test Conditions/Comments
3.0
3.3
1.3
8
0.01
5.5
3
12
0.5
V
mA
mA
μA
No load
RL = 3 kΩ to GND
0.8
V
V
V
V
μA
μA
TIN
TIN
IOUT = 1.6 mA
IOUT = −1 mA
TIN = GND to VCC 1
Receivers disabled
2.0
0.4
VCC − 0.6
5
−30
0.6
3
±5.0
±3.7
300
10
±10
+30
1.2
1.6
0.4
5
7
V
V
V
V
kΩ
±25
V
V
Ω
mA
μA
2.4
±5.2
±15
460
5.5
kbps
0.4
0.4
0.3
200
200
30
300
10
1
1
1.2
30
μs
μs
μs
ns
ns
ns
ns
V/μs
VCC = 3.3 V, all transmitter outputs loaded with 3 kΩ to ground
VCC = 3.0 V
VCC = 0 V, VOUT = ±2 V
SD = low, VOUT = 12 V
VCC = 3.3 V, RL = 3 kΩ to 7 kΩ, CL = 50 pF to 1000 pF, one
Tx switching
RL = 3 kΩ, CL = 1000 pF
Measured from +3 V to −3 V or −3 V to +3 V, VCC = +3.3 V;
RL = 3 kΩ, CL = 1000 pF, TA = 25°C
ADM1385: Input leakage current typically −10 μA when TIN = GND.
Rev. E | Page 3 of 16
ADM3202/ADM3222/ADM1385
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 2.
Parameter
VCC
V+
V−
Input Voltages
TIN
RIN
Output Voltages
TOUT
ROUT
Short-Circuit Duration
TOUT
Power Dissipation (Derates 6 mW/°C
above 50°C)
Thermal Impedance, θJA
N-16/N-18 (2-Layer Test Board)
RW-16/RW-18 (4-Layer Test Board)
R-16 (4-Layer Test Board)
RU-16 (4-Layer Test Board)
RU-20 (4-Layer Test Board)
RS-20 (4-Layer Test Board)
Operating Temperature Range
Industrial (A Version)
Storage Temperature Range
Lead Temperature
(Soldering, 10 sec)
Rating
−0.3 V to +6 V
(VCC − 0.3 V) to +14 V
+0.3 V to –14 V
−0.3 V to (V+, +0.3 V)
±30 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
±15 V
−0.3 V to (VCC + 0.3 V)
Continuous
450 mW
117°C/W
56°C/W
81°C/W
113°C/W
110°C/W
83°C/W
−40°C to +85°C
−65°C to +150°C
JEDEC industry
standard J-STD-020
Rev. E | Page 4 of 16
ADM3202/ADM3222/ADM1385
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
C1+
V+
1
16
2
15
C1–
3
ADM3202
C2+
4
TOP VIEW
(Not to Scale)
C2–
14
VCC
GND
T1OUT
EN
1
18
SD
C1+
2
17
VCC
V+
3
ADM3222
16
GND
C1–
4
15
T1OUT
C2+
5
TOP VIEW
(Not to Scale)
14
R1IN
C2–
6
13
R1OUT
R1IN
5
12
R1OUT
V–
6
11
T1IN
V–
7
12
T1IN
T2OUT
7
10
T2IN
T2OUT
8
11
T2IN
R2IN
8
9
R2OUT
R2IN
9
10
R2OUT
00071-004
13
00071-005
PIN CONFIGURATIONS (N, R, RU, AND RW PACKAGES)
Figure 5. N and RW Packages Pin Configuration
Figure 4. N, R, RU, and RW Packages Pin Configuration
PIN CONFIGURATIONS (RS AND RU PACKAGES)
V+ 3
ADM3222
VCC
18
GND
C1– 4
T1OUT
C2+ 5
C1–
C2+
5
C2–
6
15
R1OUT
V– 7
14
NC
T2OUT 8
13
T1IN
R2IN 9
12
T2IN
R2OUT 10
11
NC
17
16
NC = NO CONNECT
20 SD
C1+ 2
19
4
(SSOP/TSSOP)
TOP VIEW
(Not to Scale)
DD 1
SD
V+ 3
C2– 6
R1IN
19 VCC
ADM1385
(SSOP)
TOP VIEW
(Not to Scale)
18 GND
17 T1OUT
16 R1IN
15 R1OUT
V– 7
14 T1IN
T2OUT 8
13 T2IN
R2IN 9
12 R2OUT
NC 10
11 NC
NC = NO CONNECT
00071-007
C1+
20
2
00071-006
EN 1
Figure 7. RS Package Pin Configuration
Figure 6. RS and RU Packages Pin Configuration
Table 3. Pin Function Descriptions
Mnemonic
VCC
V+
V–
GND
C1+, C1–
C2+, C2–
TxIN
TxOUT
RxIN
RxOUT
EN
SD
SD
DD
NC
Description
Power Supply Input (3.3 V ± 0.3 V).
Internally Generated Positive Supply (+6 V nominal).
Internally Generated Negative Supply (−6 V nominal).
Ground Pin. Must be connected to 0 V.
External Capacitor 1 is connected between these pins. A 0.1 μF capacitor is recommended but larger capacitors up to 47 μF
can be used.
External Capacitor 2 is connected between these pins. A 0.1 μF capacitor is recommended but larger capacitors up to 47 μF
can be used.
Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels.
Transmitter (Driver) Outputs. These are RS-232 signal levels (typically ±9 V).
Receiver Inputs. These inputs accept RS-232 signal levels. An internal 5 kΩ pull-down resistor to GND is connected on each input.
Receiver Outputs. These are CMOS output logic levels.
(ADM3222 only) Receiver Enable. Active low. When low, the receiver outputs are enabled. When high, they are three-stated.
(ADM3222 only) Shutdown Control. Active low. When low, the charge pump is shut down and the transmitter outputs
are disabled.
(ADM1385 only) Shutdown Control. When low, the charge pump is shut down and all transmitters and receivers are disabled.
(ADM1385 only) Driver Disable. When low, the charge pump is turned off and the transmitters are disabled. The receivers
remain active.
No Connect.
Rev. E | Page 5 of 16
ADM3202/ADM3222/ADM1385
TYPICAL PERFORMANCE CHARACTERISTICS
8
8
TOUT (HIGH)
6
6
4
2
2
V+, V– (V)
0
–2
–2
–4
–4
V–
0
200
–6
00071-008
TOUT (LOW)
–6
–8
0
400
600
800
LOAD CAPACITANCE (pF)
1000
–8
1200
00071-011
Tx O/P VOLTAGE (V)
V+
4
0
Figure 8. Transmitter Output Voltage High/Low vs.
Load Capacitance @ 460 kbps
2
10
4
6
8
LOAD CURRENT (mA)
12
Figure 11. Charge Pump V+, V− vs. Load Current
350
8
Tx O/P HIGH
6
300
V+ (IMPEDANCE)
4
IMPEDANCE (Ω)
250
0
–2
200
V– (IMPEDANCE)
150
100
–4
Tx O/P LOW
50
00071-009
–6
–8
2.7
2.9
3.1
VCC (V)
3.3
0
2.7
3.5
00071-012
Tx O/P (V)
2
2.9
3.1
VCC (V)
3.3
3.5
Figure 12. Charge Pump Impedance vs. VCC
Figure 9. Transmitter Output Voltage vs. VCC
8
20
18
6
Tx O/P HIGH
ICC @ 460kbps
16
4
14
ICC (mA)
Tx O/P (V)
2
0
–2
12
ICC @ 230kbps
10
8
6
–4
00071-010
–8
0
2
4
6
8
LOAD CURRENT (mA)
10
00071-013
4
Tx O/P LOW
–6
2
0
12
Figure 10. Transmitter Output Voltage Low/High vs. Load Current
0
1000
2000
LOAD CAPACITANCE (pF)
Figure 13. Power Supply Current vs. Load Capacitance
Rev. E | Page 6 of 16
3000
ADM3202/ADM3222/ADM1385
1
T
T
CH 1 5.00V
CH 2
5.00V
M1.00µs
CH1
0V
00071-014
2
Figure 14. 460 kbps Data Transmission
Rev. E | Page 7 of 16
ADM3202/ADM3222/ADM1385
GENERAL DESCRIPTION
+3.3V INPUT
0.1µF +
10V
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
T2IN
+3.3V INPUT
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
0.1µF +
10V
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
CMOS
OUTPUTS
T2IN
+
+
T2
R1
R1IN
R2
R2OUT
R2IN
R1
R1IN
R2
R2OUT
EIA/TIA-232
INPUTS*
R2IN
SD
ADM1385
GND
EIA/TIA-232
OUTPUTS
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
Figure 17. ADM1385 Typical Operating Circuit
S1
VCC
S3
C1
S2
+
C3
S4
V+ = 2VCC
+
VCC
00071-018
GND
INTERNAL
OSCILLATOR
S1
C5
0.1µF
FROM
VOLTAGE
DOUBLER
C4
0.1µF
10V
T2OUT
T2OUT
S3
V+
GND
S2
C2
+
S4
C4
+
V– = –(V+)
GND
EIA/TIA-232
OUTPUTS
INTERNAL
OSCILLATOR
Figure 19. Charge Pump Voltage Inverter
EIA/TIA-232
INPUTS*
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
00071-015
ADM3202
Figure 15. ADM3202 Typical Operating Circuit
Rev. E | Page 8 of 16
00071-019
C3
0.1µF
6.3V
T1OUT
T2
C5
0.1µF
Figure 18. Charge Pump Voltage Doubler
+
T1
T1OUT
R1OUT
+3.3V INPUT
V–
C4
0.1µF
10V
T1
T1IN
DD
If desired, larger capacitors (up to 10 μF) can be used for
Capacitors C1 to C4.
C2+ +6.6V TO –6.6V
VOLTAGE
C2–
INVERTER
V–
C3
0.1µF
10V
00071-017
0.1µF +
10V
CMOS
INPUTS
Capacitors C3 and C4 are used to reduce the output ripple.
Their values are not critical and can be increased, if desired.
Capacitor C3 is shown connected between V+ and VCC. It is
also acceptable to connect this capacitor between V+ and GND.
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
00071-016
Figure 16. ADM3222 Typical Operating Circuit
The charge pump voltage converter consists of a 200 kHz
oscillator and a switching matrix. The converter generates a
±6.6 V supply from the input 3.3 V level. This is done in two
stages by using a switched capacitor technique as illustrated in
Figure 18 and Figure 19. First, the 3.3 V input supply is doubled
to 6.6 V by using Capacitor C1 as the charge storage element.
The +6.6 V level is then inverted to generate −6.6 V using C2
as the storage element. C3 is shown connected between V+ and
VCC but is equally effective if connected between V+ and GND.
GND
SD
ADM3222
GND
Charge Pump DC to DC Voltage Converter
R1OUT
EIA/TIA-232
INPUTS*
R2IN
+
EIA-232 to 5 V logic receivers
CMOS
OUTPUTS
R2
+
•
T2IN
R1IN
EIA/TIA-232
OUTPUTS
+
3.3 V logic to EIA-232 transmitters
CMOS
INPUTS
R1
C5
0.1µF
*INTERNAL 5kΩ PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
•
T1IN
T2OUT
EN
The internal circuitry consists of these main sections:
• A charge pump voltage converter
0.1µF +
10V
T2
R2OUT
CIRCUIT DESCRIPTION
0.1µF +
10V
T1OUT
R1OUT
CMOS
OUTPUTS
C4
0.1µF
10V
V–
T1
T1IN
CMOS
INPUTS
C3
0.1µF
6.3V
+
The ADM3202/ADM3222/ADM1385 are modifications,
enhancements, and improvements of the AD230 to AD241
family and derivatives. They are essentially plug-in compatible
and do not have any materially different applications.
C1+ +3.3V TO +6.6V VCC
VOLTAGE
C1–
V+
DOUBLER
+
CMOS technology is used to keep the power dissipation to an
absolute minimum, allowing maximum battery life in portable
applications.
0.1µF +
10V
+
The ADM3202/ADM3222/ADM1385 are RS-232 line drivers/
receivers. Step-up voltage converters coupled with level-shifting
transmitters and receivers allow RS-232 levels to be developed
while operating from a single 3.3 V supply.
ADM3202/ADM3222/ADM1385
Transmitter (Driver) Section
HIGH BAUD RATE
The drivers convert 3.3 V logic input levels into RS-232 output
levels. With VCC = 3.3 V and driving an RS-232 load, the output
voltage swing is typically ±6 V.
The ADM3202/ADM3222 feature high slew rates permitting
data transmission at rates well in excess of the EIA/RS-232E
specifications. RS-232 voltage levels are maintained at data rates
up to 460 kbps even under worst-case loading conditions. This
allows high speed data links between two terminals and is
suitable for the new generation ISDN modem standards that
require data rates of 230 kbps. The slew rate is internally
controlled to less than 30 V/μs to minimize EMI interference.
Receiver Section
The receivers are inverting level-shifters that accept RS-232
input levels and translate them into 3 V logic output levels. The
inputs have internal 5 kΩ, pull-down resistors to ground and are
protected against overvoltages up to ±30 V. Unconnected inputs
are pulled to 0 V by the internal 5 kΩ, pull-down resistor. This
results in a Logic 1 output level for unconnected inputs or for
inputs connected to GND.
The receivers have Schmitt-trigger inputs with a hysteresis level
of 0.4 V. This ensures error-free reception for both noisy inputs
and for inputs with slow transition times.
Rev. E | Page 9 of 16
ADM3202/ADM3222/ADM1385
OUTLINE DIMENSIONS
0.800 (20.32)
0.790 (20.07)
0.780 (19.81)
16
9
1
8
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
073106-B
COMPLIANT TO JEDEC STANDARDS MS-001-AB
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 20. 16-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-16)
Dimensions shown in inches and (millimeters)
10.00 (0.3937)
9.80 (0.3858)
4.00 (0.1575)
3.80 (0.1496)
9
16
1
8
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
6.20 (0.2441)
5.80 (0.2283)
1.75 (0.0689)
1.35 (0.0531)
SEATING
PLANE
0.50 (0.0197)
0.25 (0.0098)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
Figure 21. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
Rev. E | Page 10 of 16
060606-A
COMPLIANT TO JEDEC STANDARDS MS-012-AC
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
ADM3202/ADM3222/ADM1385
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 22. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
0.75 (0.0295)
45°
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 23. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
Rev. E | Page 11 of 16
1.27 (0.0500)
0.40 (0.0157)
03-27-2007-B
1
ADM3202/ADM3222/ADM1385
0.920 (23.37)
0.900 (22.86)
0.880 (22.35)
18
10
1
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
9
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
070706-A
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 24. 18-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-18)
Dimensions shown in inches and (millimeters)
7.50
7.20
6.90
11
20
5.60
5.30
5.00
1
8.20
7.80
7.40
10
0.65 BSC
0.38
0.22
SEATING
PLANE
8°
4°
0°
COMPLIANT TO JEDEC STANDARDS MO-150-AE
Figure 25. 20-Lead Shrink Small Outline Package [SSOP]
(RS-20)
Dimensions shown in millimeters
Rev. E | Page 12 of 16
0.95
0.75
0.55
060106-A
0.05 MIN
COPLANARITY
0.10
0.25
0.09
1.85
1.75
1.65
2.00 MAX
ADM3202/ADM3222/ADM1385
6.60
6.50
6.40
20
11
4.50
4.40
4.30
6.40 BSC
1
10
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
0.30
0.19
COPLANARITY
0.10
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AC
Figure 26. 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
11.75 (0.4626)
11.35 (0.4469)
18
10
7.60 (0.2992)
7.40 (0.2913)
9
0.75 (0.0295)
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
10.65 (0.4193)
10.00 (0.3937)
1.27
(0.0500)
BSC
0.51 (0.0201)
0.31 (0.0122)
SEATING
PLANE
45°
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 27. 18-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-18)
Dimensions shown in millimeters and (inches)
Rev. E | Page 13 of 16
1.27 (0.0500)
0.40 (0.0157)
060706-A
1
ADM3202/ADM3222/ADM1385
ORDERING GUIDE
Model 1
ADM3202AN
ADM3202ANZ
ADM3202ARN
ADM3202ARN-REEL
ADM3202ARN-REEL7
ADM3202ARNZ
ADM3202ARNZ-REEL
ADM3202ARNZ-REEL7
ADM3202ARU
ADM3202ARU-REEL
ADM3202ARU-REEL7
ADM3202ARUZ
ADM3202ARUZ-REEL
ADM3202ARUZ-REEL7
ADM3202ARW
ADM3202ARW-REEL7
ADM3202ARWZ
ADM3202ARWZ-REEL
ADM3202ARWZ-REEL7
ADM3222AN
ADM3222ANZ
ADM3222ARS
ADM3222ARS-REEL
ADM3222ARS-REEL7
ADM3222ARSZ
ADM3222ARSZ-REEL
ADM3222ARSZ-REEL7
ADM3222ARU
ADM3222ARU-REEL
ADM3222ARU-REEL7
ADM3222ARUZ
ADM3222ARUZ-REEL
ADM3222ARUZ-REEL7
ADM3222ARW
ADM3222ARW-REEL
ADM3222ARWZ
ADM3222ARWZ-REEL
ADM3222ARWZ-REEL7
ADM1385ARS
ADM1385ARSZ
ADM1385ARSZ-REEL
ADM1385ARSZ-REEL7
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Plastic Dual In-Line Package [PDIP]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Standard Small Outline Package [SOIC_N]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
16-Lead Standard Small Outline Package [SOIC_W]
18-Lead Plastic Dual In-Line Package [PDIP]
18-Lead Plastic Dual In-Line Package [PDIP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Thin Shrink Small Outline Package [TSSOP]
18-Lead Standard Small Outline Package [SOIC_W]
18-Lead Standard Small Outline Package [SOIC_W]
18-Lead Standard Small Outline Package [SOIC_W]
18-Lead Standard Small Outline Package [SOIC_W]
18-Lead Standard Small Outline Package [SOIC_W]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
20-Lead Shrink Small Outline Package [SSOP]
Z = RoHS Compliant Part.
Rev. E | Page 14 of 16
Package Option
N-16
N-16
R-16
R-16
R-16
R-16
R-16
R-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RW-16
RW-16
RW-16
RW-16
RW-16
N-18
N-18
RS-20
RS-20
RS-20
RS-20
RS-20
RS-20
RU-20
RU-20
RU-20
RU-20
RU-20
RU-20
RW-18
RW-18
RW-18
RW-18
RW-18
RS-20
RS-20
RS-20
RS-20
ADM3202/ADM3222/ADM1385
NOTES
Rev. E | Page 15 of 16
ADM3202/ADM3222/ADM1385
NOTES
©1998–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00071-0-7/11(E)
Rev. E | Page 16 of 16